FULL SIZE D.I.L. M package VOLTAGE CONTROLLED CRYSTAL OSCILLATORS HCMOS 5V Phase-Locked Oscillator M2010, M2011 M2015, M2016 Description Commercial: 0º to 70ºC 10 MHz to 44.736 MHz FEATURES • Cost-effective PLL solution which includes a VCXO, filter and phase detector in a single component • Simplicity of design – requires only dividers to complete the loop • Output frequency may be chosen at convenient frequency to create edges for desired timing waveforms • Start up time less than 10 ms • Guaranteed start-up with ramping DC Supply • Inputs are TTL/HCMOS compatible APPLICATIONS • Regenerating and cleaning up noisy signals • Low-jitter frequency multiplication SPECIAL APPLICATION NOTE Both the reference frequency and the output frequency, or submultiple, are input to the device. The two similar frequencies are compared, and an error signal is obtained which is applied to the VCXO. The VCXO frequency is then corrected and “locked” to the average value of the reference frequency. These PLL sub-systems incorporate all the components required for phase locked loop functionality except the external frequency divider. The phase locked loop unit includes VCXO, phase comparator, and control voltage filter. It will lock the locally generated VCXO output to an incoming reference signal of the same or digitally-related frequency. An external divider between VCXO output and phase-detector input establishes the output/reference frequency ratio. Offered in a 5V DIL (M) package, the PLL modules are built around a VCXO with customer’s choice of reference and output frequencies. The output frequency, usually chosen at a convenient frequency higher than the reference frequency, may then be used to generate desired timing waveforms. CONNECTIONS Pin Pin Pin Pin Pin Pin Pin M2010 & M2015 Not used Frequency Input #1 Frequency Input #2 Ground Output Frequency +5V +5V 1. 2. 5. 7. 8. 9. 14. M2011 & M2016 Not used Frequency Input #1 Frequency Input #2 Ground and case Output Frequency +5V +5V DOT DENOTES PIN 1 .20 MAX .20 MIN. All other pins are not present .018 – .001 100 TYP (NON ACCUMULATIVE) Pin 1 2 FET PROBE +5V 350 MHz SCOPE MA Power Supply 1 IMF 2 5 PHASE LOCK LOOP 7 GND REFERENCE FREQUENCY Y-OUTPUT 10 TTL LOAD DIVIDERS (Optional) 14 7 9 8 .300 – .005 .500 – .005 150 .300 – .005 44 MAX 14 .800 – .005 COUNTER 8 5 “M-1” Package DIVIDERS (Optional) TEST CIRCUIT ELECTRONICS 10 Commerce Dr • New Rochelle NY 10801 International Sales: +1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:[email protected] 1 of 2 VOLTAGE CONTROLLED CRYSTAL OSCILLATORS HCMOS 5V Phase-Locked Oscillator FULL SIZE D.I.L. M package M2010, M2011 M2015, M2016 Commercial: 0° to 70°C 10 MHz to 44.736 MHz ENVIRONMENTAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS Frequency Range 10 MHz to 44.736 MHz Frequency Stability Includes calibration at 25°C, operating temperature, change of input voltage, change of load, shock and vibration. Input Voltage MIN TYP MAX UNITS 4.5 5.0 5.50 volts 42 50 mA 0.4 0.5 volts volts 2.5 4 ns 0º to 70°C -55º to +125°C Temperature Cycle – Not to exceed ±5 ppm change when exposed to 2 hours maximum at each temperature from 0 to 120°C, with 25°C reference Shock – 1000 Gs, 0.35 ms, 1/2 sine wave, 3 shocks in each plane Vibration – 10-2000 Hz of .06" d.a. or 20 Gs, whichever is less Humidity – Resistant to 85° R.H. at 85°C Input Current (max. @ 5.5 VDC) Output Levels “0” Level, sinking 16 mA “1” Level, sourcing 8 mA Temperature Operating Storage VDD-.4 Rise and Fall Times from 0.8 to 2.4V, 10 TTL MECHANICAL SPECIFICATIONS Gross Leak – Each unit checked in 125°C fluorocarbon Fine Leak – Mass spectrometer leak rate less than 2 X 10-8 atmos, cc/sec of helium Pins – Kovar, 7 microinch gold over nickel Bend Test – Will withstand two bends of 90° from reference Symmetry 10 TTL, @ 1.4V 45/55 40/60 Header – Steel, 7 microinch gold over nickel percent Case – Stainless steel, type 304 Aging First year After first year 3 1 Input Requirements for Pins 2 and 5 Input Frequency, square wave Sinking at 0.4V Sourcing at 2.4V Marking – Permanent black epoxy ink or laser marked ppm ppm/yr 0.6 100 1.6 400 Resistance to Solvents – MIL STD 202, Method 215 mA mA Reference Frequency Stability Requirements M2010, M2011 ±125 ppm M2015, M2016 ±150 ppm HOW TO ORDER M 2 0 1 0- X X X . Y Y Y M is full size DIL 2010 is model type Reference frequency code* Output Leave blank for frequency straight leads code* Add G for gullwing *Consult factory for frequency codes. SS# Rev. M2010 B ELECTRONICS Unless customer-specific terms and conditions are signed by an officer of MF Electronics, the sale of this and all MF Electronics products are subject to terms and conditions set forth at www.mfelectronics.com/terms 10 Commerce Dr • New Rochelle NY 10801 International Sales: +1.914-712-2200 • USA Sales: +1.800.331.1236 • Fax: 914.712.2290 • www.mfelectronics.com • email:[email protected] 2 of 2