Download Datasheet

LM2902W
Low-power quad operational amplifier
Datasheet - production data
Description
This circuit consists of four independent, highgain operational amplifiers which have frequency
compensation implemented internally and are
designed especially for automotive and industrial
control systems.
The device operates from a single power supply
over a wide range of voltages. Operation from
split power supplies is also possible and the low
power supply current drain is independent of the
magnitude of the power supply voltage.
All the pins are protected against electrostatic
discharges up to 800 V.
Features
Wide gain bandwidth: 1.3 MHz
Input common-mode voltage range includes
negative rail
Large voltage gain: 100 dB
Very low supply current per amplifier:
375 µA
Low input bias current: 20 nA
Low input offset current: 2 nA
ESD internal protection: 800 V
Wide power supply range
Single supply: 3 V to 30 V
Dual supplies: ±1.5 V to ±15 V
February 2016
DocID9922 Rev 10
This is information on a product in full production.
1/19
www.st.com
Contents
LM2902W
Contents
1
Schematic diagram.......................................................................... 3
2
Package pin connections................................................................ 4
3
4
Absolute maximum ratings and operating conditions ................. 5
Electrical characteristics ................................................................ 6
5
Electrical characteristic curves ...................................................... 8
6
Typical single-supply applications .............................................. 11
7
Macromodel ................................................................................... 13
8
Package information ..................................................................... 14
8.1
SO14 package information .............................................................. 15
8.2
TSSOP14 package information ....................................................... 16
9
Ordering information..................................................................... 17
10
Revision history ............................................................................ 18
2/19
DocID9922 Rev 10
LM2902W
1
Schematic diagram
Schematic diagram
Figure 1: Schematic diagram (1/4 LM2902W)
DocID9922 Rev 10
3/19
Package pin connections
2
LM2902W
Package pin connections
Figure 2: SO14 and TSSOP14 pin connections (top view)
4/19
DocID9922 Rev 10
LM2902W
3
Absolute maximum ratings and operating
conditions
Absolute maximum ratings and operating conditions
Table 1: Absolute maximum ratings
Symbol
Parameter
VCC
Supply voltage
Vid
Differential input voltage
Vi
32
Input voltage
Input current
Rthja
Thermal resistance junction to ambient
Thermal resistance junction to case
HBM: human body model
MM: machine model
V
+ 0.3
Infinite
(2)
Storage temperature range
ESD
+
(VCC )
-0.3 to
(1)
Tstg
Rthjc
Unit
±16 to 32
Output short-circuit to ground
Iin
Value
(3)
(3)
50
mA
-65 to 150
°C
SO14
105
TSSOP14
100
SO14
31
TSSOP14
32
(4)
°C/W
800
(5)
100
CDM: charged device model
(6)
V
1500
Notes:
(1)
+
Short-circuits from the output to VCC can cause excessive heating and potential destruction. The maximum
+
output current is approximately 20 mA, independent of the magnitude of VCC
(2)
This input current only exists when the voltage at any of the input leads is driven negative. It is due to the
collector-base junction of the input PNP transistor becoming forward biased and thereby acting as an input diode
clamp. In addition to this diode action, there is also NPN parasitic action on the IC chip. This transistor action can
cause the output voltages of the op amps to go to the VCC voltage level (or to ground for a large overdrive) for the
time during which an input is driven negative. This is not destructive and normal output is restored for input
voltages higher than -0.3 V.
(3)
Rthja/c are typical values.
(4)
Human body model: a 100 pF capacitor is charged to the specified voltage, then discharged through a 1.5 kΩ
resistor between two pins of the device. This is done for all couples of connected pin combinations while the other
pins are floating.
(5)
Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two
pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of connected
pin combinations while the other pins are floating.
(6)
Charged device model: all pins and the package are charged together to the specified voltage and then
discharged directly to the ground through only one pin. This is done for all pins.
Table 2: Operating conditions
Symbol
VCC
Parameter
Value
Supply voltage
Unit
3 to 30
Vicm
Common mode input voltage range
Toper
Operating free-air temperature range
(VCC )
Tmin ≤ Tamb ≤ Tmax
DocID9922 Rev 10
+
to (VCC ) - 1.5
(VCC )
to
+
(VCC )
-40 to 125
V
-2
°C
5/19
Electrical characteristics
4
LM2902W
Electrical characteristics
Table 3: VCC+ = 5 V, VCC- = ground, VO = 1.4 V, Tamb = 25 °C (unless otherwise stated)
Symbol
Parameter
Test conditions
Min.
LM2902W
Vi o
Input offset voltage
(1)
ΔVio/ΔT
Input offset voltage
drift
Iio
Input offset current
DIio
Input offset current
drift
Iib
Input bias current
(2)
Typ.
Max.
2
7
LM2902AW
2
Tmin ≤ Tamb ≤ Tmax, LM2902W
9
Tmin ≤ Tamb ≤ Tmax, LM2902AW
4
Tamb = 25 °C
7
30
2
30
Tmin ≤ Tamb ≤ Tmax
40
Tamb = 25 °C
10
200
20
150
Tmin ≤ Tamb ≤ Tmax
300
Unit
mV
µV/°C
nA
pA/°C
nA
+
Avd
SVR
Large signal
voltage gain
Supply voltage
rejection ratio
VCC = 15 V, RL = 2 kΩ, Vο = 1.4 V to 11.4 V,
Tamb = 25 °C
50
V/mV
+
VCC = 15 V, RL = 2 kΩ, Vο = 1.4 V to 11.4 V,
Tmin ≤ Tamb ≤ Tmax
25
RS ≤ 10 kΩ, Tamb = 25 °C
65
RS ≤ 10 kΩ, Tmin ≤ Tamb ≤ Tmax
65
+
Tamb = 25 °C, VCC = 5 V
ICC
Supply current
(all op amps, no
load)
Tamb = 25 °C,
+
VCC
Io
Isink
Common-mode
rejection ratio
Output short-circuit
current
Output sink current
High-level output
voltage
= 30 V
1.5
3
+
0.9
1.2
+
1.5
3
Tmin ≤ Tamb ≤ Tmax, VCC = 5 V
RS ≤ 10 kΩ, Tamb = 25 °C
70
RS ≤ 10 kΩ, Tmin ≤ Tamb ≤ Tmax
60
+
Vid = 1 V, VCC = 15 V, Vo = 2 V
SR
Slew rate
40
= 15 V, Vo = 2 V
10
20
Vid = -1 V,
+
VCC
= 15 V, Vo = 0.2 V
12
50
+
26
27
VCC = 30 V, RL = 2 kΩ, Tmin = Tamb = Tmax
+
26
+
VCC
= 30 V, RL = 10 kΩ, Tamb = 25 °C
27
+
VCC
= 30 V, RL = 10 kΩ, Tmin = Tamb = Tmax
27
+
Low level output
voltage
20
Vid = -1 V,
VCC = 5 V, RL = 2 kΩ, Tamb = 25 °C
VOL
80
+
VCC
+
VCC
dB
1.2
VCC = 30 V, RL = 2 kΩ, Tamb = 25 °C
VOH
110
0.7
Tmin ≤ Tamb ≤ Tmax, VCC = 30 V
CMR
100
= 5 V, RL = 2 kΩ, Tmin = Tamb = Tmax
mA
dB
70
mA
µA
28
V
3.5
3
RL = 10 kΩ, Tamb = 25 °C
5
RL = 10 kΩ, Tmin = Tamb = Tmax
20
20
mV
+
6/19
VCC = 15 V, Vin = 0.5 to 3 V, RL = 2 kΩ,
CL = 100 pF, unity gain
DocID9922 Rev 10
0.24
0.4
V/µs
LM2902W
Symbol
SR
Electrical characteristics
Parameter
Test conditions
+
VCC
= 15 V, Vin = 0.5 to 3 V, RL = 2 kΩ,
CL = 100 pF, unity gain, Tmin ≤ Tamb ≤ Tmax
Slew rate
Typ.
0.14
Max.
Unit
V/µs
+
GBP
Gain bandwidth
product
VCC = 30 V, Vin = 10 mV, RL = 2 kΩ,
CL = 100 pF
THD
Total harmonic
distortion
f = 1 kHz, AV = 20 dB, RL = 2 kΩ, Vo = 2 Vpp,
+
CL = 100 pF, VCC = 30 V
en
Equivalent input
noise voltage
Channel
(3)
separation
VO1/VO2
Min.
1.3
MHz
0.015
%
f = 1 kHz, RS = 100 Ω, VCC = 30 V
40
nV/√Hz
1 kHz ≤ f ≤ 20 kHz
120
dB
+
Notes:
(1)
+
+
VO = 1.4 V, RS = 0 Ω, 5 V < VCC < 30 V, 0 V < Vic < (VCC ) - 1.5 V.
(2)
The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output, so
there is no change in the load on the input lines.
(3)
Due to the proximity of external components, ensure that stray capacitance does not cause coupling between these external
parts. Typically, this can be detected as this type of capacitance increases at higher frequencies.
DocID9922 Rev 10
7/19
Electrical characteristic curves
5
8/19
LM2902W
Electrical characteristic curves
Figure 3: Input bias current vs. Tamb
Figure 4: Input voltage range
Figure 5: Current limiting
Figure 6: Supply current
Figure 7: Gain bandwidth product
Figure 8: Voltage follower pulse response (VCC = 15 V)
DocID9922 Rev 10
LM2902W
Electrical characteristic curves
Figure 9: Common-mode rejection ratio
Figure 10: Output characteristics (sink)
Figure 11: Open-loop frequency response
Figure 12: Voltage follower pulse response
(VCC = 30 V)
Figure 13: Large signal frequency response
Figure 14: Output characteristics (source)
DocID9922 Rev 10
9/19
Electrical characteristic curves
LM2902W
Figure 15: Input current
Figure 16: Voltage gain
Figure 17: Power supply and common-mode
rejection ratio
Figure 18: Large signal voltage gain
10/19
DocID9922 Rev 10
LM2902W
6
Typical single-supply applications
Typical single-supply applications
Figure 19: AC coupled inverting amplifier
Figure 20: AC coupled non-inverting amplifier
Figure 21: Non-inverting DC gain
Figure 22: DC summing amplifier
Figure 23: Active bandpass filter
Figure 24: High input Z adjustable gain DC
instrumentation amplifier
DocID9922 Rev 10
11/19
Typical single-supply applications
LM2902W
Figure 25: High input Z, DC differential amplifier
Figure 26: Low drift peak detector
Figure 27: Using symmetrical amplifiers to reduce input current (general concept)
12/19
DocID9922 Rev 10
LM2902W
7
Macromodel
Macromodel
An accurate macromodel of the LM2902W is available on STMicroelectronics’ web site at
www.st.com. This model is a trade-off between accuracy and complexity (that is, time
simulation) of the LM2902W operational amplifiers. It emulates the nominal performances
of a typical device within the specified operating conditions mentioned in the datasheet. It
also helps to validate a design approach and to select the right operational amplifier, but it
does not replace on-board measurements.
DocID9922 Rev 10
13/19
Package information
8
LM2902W
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
®
®
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
®
ECOPACK is an ST trademark.
14/19
DocID9922 Rev 10
LM2902W
8.1
Package information
SO14 package information
Figure 28: SO14 package outline
Table 4: SO14 mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
Inches
Max.
Min.
Typ.
Max.
A
1.35
1.75
0.05
0.068
A1
0.10
0.25
0.004
0.009
A2
1.10
1.65
0.04
0.06
B
0.33
0.51
0.01
0.02
C
0.19
0.25
0.007
0.009
D
8.55
8.75
0.33
0.34
E
3.80
4.0
0.15
0.15
e
1.27
0.05
H
5.80
6.20
0.22
0.24
h
0.25
0.50
0.009
0.02
L
0.40
1.27
0.015
0.05
k
ddd
8° (max)
0.10
DocID9922 Rev 10
0.004
15/19
Package information
8.2
LM2902W
TSSOP14 package information
Figure 29: TSSOP14 package outline
aaa
Table 5: TSSOP14 mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.20
A1
0.05
A2
0.80
b
Max.
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.90
5.00
5.10
0.193
0.197
0.201
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.176
e
L
k
aaa
1.00
0.65
0.45
L1
16/19
Inches
0.60
0.0256
0.75
0.018
1.00
0°
0.024
0.030
0.039
8°
0.10
DocID9922 Rev 10
0°
8°
0.004
LM2902W
9
Ordering information
Ordering information
Table 6: Order codes
Order code
Temperature range
Package
LM2902WDT
LM2902WYDT
(1)
LM2902AWYDT
(1)
LM2902WYPT
(1)
LM2902AWYPT
(1)
Marking
SO14
2902W
SO14
(automotive grade level)
2902WY
-40 °C to 125 °C
LM2902WPT
Packing
TSSOP14
TSSOP14
(automotive grade level)
Tape and
reel
2902AWY
2902W
2902WY
2902AWY
Notes:
(1)
Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening
according to AEC Q001 & Q 002 or equivalent.
DocID9922 Rev 10
17/19
Revision history
10
LM2902W
Revision history
Table 7: Document revision history
Date
Revision
01-Sep-2003
1
Initial release.
01-Nov-2005
2
Table data reformatted for easier use in Electrical characteristics on
page 4.
Minor grammatical and formatting changes throughout.
01-Jan-2006
3
LM2902WYPT PPAP reference inserted in order codes table, see
Section 7 on page 16.
01-May-2006
4
Minimum value of slew rate at 25°C and on full temperature range
added in Table 3 on page 5.
20-Jul-2007
5
Corrected document title to “quad operational amplifier”.
Corrected ESD value for HBM to 800V.
Corrected thermal resistance junction to ambient values in Table 1:
Absolute maximum ratings.
Updated electrical characteristics curves.
Added Section 5: Macromodel.
Added automotive grade order codes in Section 7 on page 16.
15-Jan-2008
6
Corrected footnotes for automotive grade order codes.
17-Oct-2008
7
Added enhanced Vio version: LM2902AW.
Corrected VOH min parameter at Vcc=5V in Table 3 on page 5.
8
Modified Chapter 5: Macromodel.
Deleted LM2902WYD and LM2902AWYD order codes from Table 7
and modified status of LM2902WYPT and LM2902AWYPT order
codes.
9
Table 3: DVio replaced with ΔVio/ΔT
Table 7: Removed the order codes LM2902WN and LM2902WD;
replaced the order codes LM2902WDT and LM2902AWDT with
LM2902WYDT and LM2902AWYDT respectively.
16-Feb-2012
22-Jul-2013
19-Feb-2016
10
Changes
Updated layout
Removed DIP14 package and all information pertaining to it
Removed “D, plastic micropackage” and “P, thin shrink small outline
package” respectively from the SO14 and TSSOP14 silhouettes.
Section 8.1: "SO14 package information": replaced SO14 package
outline and mechanical data
Section 8.2: "TSSOP14 package information": updated E1 max mm
value, L1 value, and added "aaa" information.
Table 6: "Order codes": added order code LM2902WDT
18/19
DocID9922 Rev 10
LM2902W
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST
products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the
design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2016 STMicroelectronics – All rights reserved
DocID9922 Rev 10
19/19