PIC18F2XJXX/4XJXX Family Programming Specification

PIC18F2XJXX/4XJXX FAMILY
Flash Microcontroller Programming Specification
1.0
DEVICE OVERVIEW
2.0
This document includes the programming specifications
for the following devices:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PIC18F24J10
PIC18F25J10
PIC18F44J10
PIC18F45J10
PIC18F24J11
PIC18F25J11
PIC18F26J11
PIC18F44J11
PIC18F45J11
PIC18F46J11
PIC18F26J13
PIC18F27J13
PIC18F46J13
PIC18F47J13
PIC18F24J50
PIC18F25J50
PIC18F26J50
PIC18F44J50
PIC18F45J50
PIC18F46J50
PIC18F26J53
PIC18F27J53
PIC18F46J53
PIC18F47J53
TABLE 2-1:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PIC18LF24J10
PIC18LF25J10
PIC18LF44J10
PIC18LF45J10
PIC18LF24J11
PIC18LF25J11
PIC18LF26J11
PIC18LF44J11
PIC18LF45J11
PIC18LF46J11
PIC18LF26J13
PIC18LF27J13
PIC18LF46J13
PIC18LF47J13
PIC18LF24J50
PIC18LF25J50
PIC18LF26J50
PIC18LF44J50
PIC18LF45J50
PIC18LF46J50
PIC18LF26J53
PIC18LF27J53
PIC18LF46J53
PIC18LF47J53
PROGRAMMING OVERVIEW
OF THE PIC18F2XJXX/4XJXX
FAMILY
The PIC18F2XJXX/4XJXX Family devices are
programmed using In-Circuit Serial Programming™
(ICSP™). This programming specification applies to
devices of the PIC18F2XJXX/4XJXX Family in all
package types.
2.1
Pin Diagrams
The pin diagrams for the PIC18F2XJXX/4XJXX Family
are shown in Figure 2-1 and Figure 2-2. The pins
required for programming are listed in Table 2-1 and
shown in bold lettering in the diagrams.
PIN DESCRIPTIONS (DURING PROGRAMMING): PIC18F2XJXX/4XJXX FAMILY
During Programming
Pin Name
MCLR
VDD and AVDD(1)
VSS and
AVSS(1)
VDDCORE/VCAP
Pin Name
Pin Type
Pin Description
MCLR
P
Programming Enable
VDD
P
Power Supply
VSS
P
Ground
VDDCORE
P
Regulated Power Supply for Microcontroller Core
VCAP
I
Filter Capacitor for On-chip Voltage Regulator
RB6
PGC
I
Serial Clock
RB7
PGD
I/O
Serial Data
Legend: I = Input, O = Output, P = Power
Note 1: All power supply and ground pins must be connected, including analog supplies (AVDD) and ground
(AVSS).
 2008-2015 Microchip Technology Inc.
DS30009687F-page 1
PIC18F2XJXX/4XJXX FAMILY
FIGURE 2-1:
PIC18F2XJXX/4XJXX FAMILY PIN DIAGRAMS
MCLR
RA0
RA1
RA2
RA3
VDDCORE/VCAP
RA5
VSS
OSC1
OSC2
RC0
RC1
RC2
RC3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PIC18F2XJ1X
PIC18F2XJ5X
28-Pin SPDIP, SOIC, SSOP
28
27
26
25
24
23
22
21
20
19
18
17
16
15
RB7/PGD
RB6/PGC
RB5
RB4
RB3
RB2
RB1
RB0
VDD
VSS
RC7
RC6
RC5
RC4
RA1
RA0
MCLR
RB7/PGD
RB6/PGC
RB5
RB4
28-Pin QFN
28 27 26 25 24 23 22
RA2
RA3
VDDCORE/VCAP
RA5
VSS
OSC1/CLKI
OSC2/CLKO
1
2
3
4
5
6
7
PIC18F2XJ1X
PIC18F2XJ5X
21
20
19
18
17
16
15
RB3
RB2
RB1
RB0
VDD
VSS
RC7
RC0
RC1
RC2
RC3
RC4
RC5
RC6
8 9 10 11 12 13 14
DS30009687F-page 2
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
FIGURE 2-2:
PIC18F2XJXX/4XJXX FAMILY PIN DIAGRAMS (CONTINUED)
40-Pin PDIP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
PIC18F4XJ1X
MCLR
RA0
RA1
RA2
RA3
VDDCORE/VCAP
RA5
RE0
RE1
RE2
VDD
VSS
OSC1
OSC2
RC0
RC1
RC2
RC3
RD0
RD1
44
43
42
41
40
39
38
37
36
35
34
RC6
RC5
RC4
RD3
RD2
RD1
RD0
RC3
RC2
RC1
RC0
44-Pin QFN
RB7/PGD
RB6/PGC
RB5
RB4
RB3
RB2
RB1
RB0
VDD
VSS
RD7
RD6
RD5
RD4
RC7
RC6
RC5
RC4
RD3
RD2
PIC18F4XJ1X
PIC18F4XJ5X
33
32
31
30
29
28
27
26
25
24
23
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
8
9
10
11
OSC2
OSC1
VSS
AVSS
VDD
AVDD
RE2
RE1
RE0
RA5
VDDCORE/VCAP
RB3
NC
RB4
RB5
RB6/PGC
RB7/PGD
MCLR
RA0
RA1
RA2
RA3
RC7
RD4
RD5
RD6
RD7
VSS
AVDD
VDD
RB0
RB1
RB2
44
43
42
41
40
39
38
37
36
35
34
RC6
RC5
RC4
RD3
RD2
RD1
RD0
RC3
RC2
RC1
NC
44-Pin TQFP
PIC18F4XJ1X
PIC18F4XJ5X
33
32
31
30
29
28
27
26
25
24
23
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
8
9
10
11
NC
RC0
OSC2
OSC1
VSS
VDD
RE2
RE1
RE0
RA5
VDDCORE/VCAP
NC
NC
RB4
RB5
RB6/PGC
RB7/PGD
MCLR
RA0
RA1
RA2
RA3
RC7
RD4
RD5
RD6
RD7
VSS
VDD
RB0
RB1
RB2
RB3
 2008-2015 Microchip Technology Inc.
DS30009687F-page 3
PIC18F2XJXX/4XJXX FAMILY
2.1.1
PIC18F2XJXX/4XJXX/
LF2XJXX/LF4XJXX DEVICES AND
THE ON-CHIP VOLTAGE
REGULATOR
PIC18FXXJXX devices have an internal core voltage
regulator. On these devices (“PIC18F” in the part number), the regulator is always enabled. The regulator
input is taken from the VDD pins of the microcontroller.
The output of the regulator is supplied to the VDDCORE/
VCAP pin. On these devices, this pin simultaneously
serves as both regulator output and microcontroller
core power input pin. For these devices, the VDDCORE/
VCAP pin should be tied only to a capacitor.
2.2
The PIC18F2XJXX/4XJXX Family of devices offers
program memory sizes of 16, 32, 64, and 128 Kbytes.
The memory sizes for different members of the family
are shown in Table 2-2. The overall memory maps for
all the devices are shown in Figure 2-4.
TABLE 2-2:
Device*
PIC18LFXXJXX devices do not have an internal core
voltage regulator. On the low-voltage devices (LF),
power must be externally supplied to both VDD and
VDDCORE/VCAP.
PROGRAM MEMORY SIZES
FOR PIC18F2XJXX/4XJXX
FAMILY DEVICES
Program
Memory
(Kbytes)
Location of Flash
Configuration
Words
16
3FF8h:3FFFh
32
7FF8h:7FFFh
64
FFF8h:FFFFh
128
1FFF8h:1FFFFh
PIC18F24J10
PIC18F44J10
PIC18F24J11
Whether or not the regulator is used, it is always good
design practice to have sufficient capacitance on all
supply pins. Examples are shown in Figure 2-3.
PIC18F44J11
PIC18F24J50
PIC18F44J50
The specifications for core voltage and capacitance are
listed in Section 6.0 “AC/DC Characteristics Timing
Requirements for Program/Verify Test Mode”.
FIGURE 2-3:
Memory Maps
PIC18F25J10
PIC18F45J10
PIC18F25J11
CONNECTIONS FOR THE
ON-CHIP REGULATOR
PIC18F45J11
PIC18F25J50
PIC18F2XJXX/4XJXX Devices (Regulator Enabled)
PIC18F45J50
3.3V
PIC18F26J11
PIC18F2XJXX/4XJXX
PIC18F46J11
VDD
CF
PIC18F26J13
VDDCORE/VCAP
PIC18F46J13
VSS
PIC18F26J50
PIC18F46J50
PIC18F26J53
PIC18LF2XJXX/4XJXX Devices (Regulator Disabled)
(VDD VDDCORE)
2.5V
PIC18F46J53
PIC18F27J13
PIC18LF2XJXX/4XJXX
PIC18F47J13
VDD
PIC18F27J53
VDDCORE/VCAP
VSS
(VDD VDDCORE)
2.5V 3.3V
PIC18LF2XJXX/4XJXX
VDD
PIC18F47J53
*
Includes PIC18F and PIC18LF devices.
For purposes of code protection, the program memory
for every device is treated as a single block. Therefore,
enabling code protection, thus protecting the entire
code memory and not individual segments.
VDDCORE/VCAP
VSS
DS30009687F-page 4
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
The Configuration Words for these devices are located
at addresses 300000h through 300007h. These are
implemented as three pairs of volatile memory
registers. Each register is automatically loaded from a
copy stored at the end of program memory. For this
reason, the last four words (or eight bytes) of the code
space (also called the Flash Configuration Words)
should be written with Configuration data and not
executable code. The addresses of the Flash
Configuration Words are listed in Table 2-2. Refer to
section Section 5.0 “Configuration Word” for more
information.
Locations 3FFFFEh and 3FFFFFh are reserved for the
Device ID bits. These bits, which may be used by the
programmer to identify what device type is being programmed, are described in Section 5.1 “Device ID
Word”. These Device ID bits read out normally, even
after code protection.
 2008-2015 Microchip Technology Inc.
2.2.1
MEMORY ADDRESS POINTER
Memory in the device address space (000000h to
3FFFFFh) is addressed via the Table Pointer register,
which in turn is comprised of three registers:
• TBLPTRU at RAM address 0FF8h
• TBLPTRH at RAM address 0FF7h
• TBLPTRL at RAM address 0FF6h
TBLPTRU
TBLPTRH
TBLPTRL
Addr[21:16]
Addr[15:8]
Addr[7:0]
The 4-bit command, ‘0000’ (core instruction), is used to
load the Table Pointer prior to using many read or write
operations.
DS30009687F-page 5
PIC18F2XJXX/4XJXX FAMILY
FIGURE 2-4:
MEMORY MAPS FOR PIC18F2XJXX/4XJXX FAMILY DEVICES(1)
PIC18FX4JXX
(16 Kbytes)
Code Memory
PIC18FX5JXX
(32 Kbytes)
Code Memory
PIC18FX6JXX
(64 Kbytes)
Code Memory
Flash Conf. Words
PIC18FX7JXX
(128 Kbytes)
Code Memory
003FFFh
Flash Conf. Words
007FFFh
Flash Conf. Words
Unimplemented
Read as ‘0’
000000h
Unimplemented
Read as ‘0’
00FFFFh
Unimplemented
Read as ‘0’
Flash Conf. Words
01FFFFh
Unimplemented
Read as ‘0’
1FFFFFh
200000h
Configuration
Space
Configuration
Space
Configuration
Space
Configuration
Space
Configuration
Words
Configuration
Words
Configuration
Words
Configuration
Words
Configuration
Space
Configuration
Space
Configuration
Space
Configuration
Space
Device IDs
Device IDs
Device IDs
Device IDs
2FFFFFh
300000h
300007h(2)
3FFFFEh
3FFFFFh
Memory spaces are unimplemented or unavailable in normal execution mode and read as ‘0’.
Memory spaces are read-only (Device IDs) or cannot be directly programmed by ICSP™ (Configuration Words).
Note 1:
2:
Sizes of memory areas are not to scale. Sizes of accessible memory areas are enhanced to show detail.
Addresses 300006h and 300007h are unimplemented in PIC18F45J10 Family devices.
DS30009687F-page 6
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
2.3
Overview of the Programming
Process
2.4
Figure 2-5 shows the high-level overview of the
programming process in which a Bulk Erase is performed first, then the code memory is programmed.
Since only nonvolatile Configuration Words are within
the code memory space, the Configuration Words are
also programmed as code. Code memory (including
the Configuration Words) is then verified to ensure that
programming was successful.
FIGURE 2-5:
Entering and Exiting ICSP™
Program/Verify Mode
Entry into ICSP modes for PIC18F2XJXX/4XJXX Family
devices is somewhat different than previous PIC18
devices. As shown in Figure 2-6, entering ICSP
Program/Verify mode requires three steps:
1.
2.
3.
Voltage is briefly applied to the MCLR pin.
A 32-bit key sequence is presented on PGD.
Voltage is reapplied to MCLR and held.
The programming voltage applied to MCLR is VIH, or
essentially, VDD. There is no minimum time requirement
for holding at VIH. After VIH is removed, an interval of at
least P19 must elapse before presenting the key
sequence on PGD.
HIGH-LEVEL
PROGRAMMING FLOW
Start
The key sequence is a specific 32-bit pattern,
‘0100 1101 0100 0011 0100 1000 0101 0000’,
which is more easily remembered as 4D434850h in
hexadecimal. The device will enter Program/Verify
mode only if the sequence is valid. The Most Significant
bit of the Most Significant nibble must be shifted in first.
Enter ICSP™
Perform Bulk
Erase
Once the key sequence is complete, VIH must be
applied to MCLR and held at that level for as long as
Program/Verify mode is to be maintained. An interval of
at least time, P20 and P12, must elapse before
presenting data on PGD. Signals appearing on PGD
before P12 has elapsed may not be interpreted as valid.
Program Memory
Verify Program
On successful entry, the program memory can be
accessed and programmed in serial fashion. While in
the Program/Verify mode, all unused I/Os are placed in
the high-impedance state.
Exit ICSP™
Exiting Program/Verify mode is done by removing VIH
from MCLR, as shown in Figure 2-7. The only
requirement for exit is that an interval, P16, should
elapse between the last clock and program signals on
PGC and PGD before removing VIH.
Done
When VIH is reapplied to MCLR, the device will enter
the ordinary operational mode and begin executing the
application instructions.
FIGURE 2-6:
ENTERING PROGRAM/VERIFY MODE
P13
P20
P1
MCLR
VDD
P12
VIH
VIH
Program/Verify Entry Code = 4D434850h
0
b31
PGD
1
b30
0
b29
0
b28
1
b27
...
0
b3
0
b2
0
b1
0
b0
PGC
P19
 2008-2015 Microchip Technology Inc.
P2B
P2A
DS30009687F-page 7
PIC18F2XJXX/4XJXX FAMILY
FIGURE 2-7:
EXITING PROGRAM/
VERIFY MODE
P16
Throughout this specification, commands and data are
presented as illustrated in Table 2-4. The 4-bit command
is shown Most Significant bit (MSb) first. The command
operand or “Data Payload” is shown <MSB><LSB>.
Figure 2-8 demonstrates how to serially present a 20-bit
command/operand to the device.
P17
VIH
MCLR
2.5.2
VDD
The core instruction passes a 16-bit instruction to the
CPU core for execution. This is needed to set up
registers as appropriate for use with other commands.
VIH
PGD
CORE INSTRUCTION
PGC
TABLE 2-3:
COMMANDS FOR
PROGRAMMING
PGD = Input
4-Bit
Command
Description
2.5
Serial Program/Verify Operation
The PGC pin is used as a clock input pin and the PGD
pin is used for entering command bits and data input/
output during serial operation. Commands and data are
transmitted on the rising edge of PGC, latched on the
falling edge of PGC, and are Least Significant bit (LSb)
first.
2.5.1
FOUR-BIT COMMANDS
All instructions are 20 bits, consisting of a leading 4-bit
command followed by a 16-bit operand, which depends
on the type of command being executed. To input a
command, PGC is cycled four times. The commands
needed for programming and verification are shown in
Table 2-3.
0000
Shift out TABLAT register
0010
Table Read
1000
Table Read, Post-Increment
1001
Table Read, Post-Decrement
1010
Table Read, Pre-Increment
1011
Table Write
1100
Table Write, Post-Increment by 2
1101
Table Write, Start Programming,
Post-Increment by 2
1110
Table Write, Start Programming
1111
TABLE 2-4:
Depending on the 4-bit command, the 16-bit operand
represents 16 bits of input data or eight bits of input
data and eight bits of output data.
FIGURE 2-8:
Core Instruction
(Shift in 16-bit instruction)
SAMPLE COMMAND
SEQUENCE
4-Bit
Command
Data
Payload
1101
3C 40
Core Instruction
Table Write,
post-increment by 2
TABLE WRITE, POST-INCREMENT TIMING (1101)
P2
1
2
3
4
P2A
P2B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
1
3
4
PGC
P5A
P5
P4
P3
PGD
1
0
1
1
0
0
0
0
4-Bit Command
0
0
0
1
0
0
0
4
C
16-Bit Data Payload
1
1
1
1
0
0
n
n
n
n
3
Fetch Next 4-Bit Command
PGD = Input
DS30009687F-page 8
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
3.0
DEVICE PROGRAMMING
TABLE 3-1:
Programming includes the ability to erase or write the
memory within the device.
4-Bit
Command
The EECON1 register is used to control Write or Row
Erase operations. The WREN bit must be set to enable
writes; this must be done prior to initiating a write
sequence. It is strongly recommended that the WREN
bit only be set immediately prior to a program or erase
operation.
The FREE bit must be set in order to erase the program
space being pointed to by the Table Pointer. The erase
or write sequence is initiated by setting the WR bit.
3.1
ICSP™ Erase
3.1.1
ICSP BULK ERASE
The PIC18F2XJXX/4XJXX Family devices may be
Bulk Erased by writing 0180h to the table address,
3C0005h:3C0004h. The basic sequence is shown in
Table 3-1 and demonstrated in Figure 3-1.
Since the code-protect Configuration bit is stored in the
program code within code memory, a Bulk Erase
operation will also clear any code-protect settings for
the device.
BULK ERASE COMMAND
SEQUENCE
Data
Payload
0000
0000
0000
0000
0000
0000
1100
0000
0000
0000
0000
0000
0000
1100
0E
6E
0E
6E
0E
6E
01
0E
6E
0E
6E
0E
6E
80
0000
0000
00 00
00 00
3C
F8
00
F7
05
F6
01
3C
F8
00
F7
04
F6
80
Core Instruction
MOVLW 3Ch
MOVWF TBLPTRU
MOVLW 00h
MOVWF TBLPTRH
MOVLW 05h
MOVWF TBLPTRL
Write 01h to 3C0005h
MOVLW 3Ch
MOVWF TBLPTRU
MOVLW 00h
MOVWF TBLPTRH
MOVLW 04h
MOVWF TBLPTRL
Write 80h TO 3C0004h to
erase entire device.
NOP
Hold PGD low until erase
completes.
FIGURE 3-1:
BULK ERASE FLOW
Start
The actual Bulk Erase function is a self-timed
operation. Once the erase has started (falling edge of
the 4th PGC after the NOP command), serial execution
will cease until the erase completes (parameter P11).
During this time, PGC may continue to toggle but PGD
must be held low.
Write 0101h
to 3C0005h
Write 8080h to
3C0004h to Erase
Entire Device
Delay P11 + P10
Time
Done
FIGURE 3-2:
BULK ERASE TIMING
P10
1
2
3
4
2
1
15 16
1
2
3
4
1
2
15 16
1
2
3
4
1
2
n
n
PGC
P5A
P5
PGD
0
0
1
1
4-Bit Command
1
1
0
16-Bit
Data Payload
0
P5A
P5
0
0
0
0
4-Bit Command
0
0
0
0
16-Bit
Data Payload
P11
0
0
0
0
4-Bit Command
Erase Time
16-Bit
Data Payload
PGD = Input
 2008-2015 Microchip Technology Inc.
DS30009687F-page 9
PIC18F2XJXX/4XJXX FAMILY
3.1.2
ICSP™ ROW ERASE
Family device. The timing diagram that details the Row
Erase command and parameter P10 is shown in
Figure 3-3.
It is possible to erase one row (1024 bytes of data),
provided the block is not code-protected or erase/writeprotected. Rows are located at static boundaries
beginning at program memory address 000000h,
extending to the internal program memory limit. Refer
to Section 2.2 “Memory Maps”).
Note 1: If the last row of program memory is
erased, bit 3 of CONFIG1H must also be
programmed as ‘0’.
The Row Erase duration is internally timed. After the
WR bit in EECON1 is set, a NOP instruction is issued,
where the 4th PGC is held high for the duration of the
Row Erase time, P10.
2: The TBLPTR register can point at any
byte within the row intended for erase.
3: If code protection has been enabled,
ICSP Bulk Erase (all program memory
erased) operations can be used to
disable code protection. ICSP Row Erase
operations cannot be used to disable
code protection.
The code sequence to Row Erase a PIC18F2XJXX/
4XJXX Family device is shown in Table 3-2. The
flowchart shown in Figure 3-4 depicts the logic
necessary to completely erase a PIC18F2XJXX/4XJXX
TABLE 3-2:
ERASE CODE MEMORY CODE SEQUENCE
4-Bit
Command
Data Payload
Core Instruction
Step 1: Enable memory writes.
0000
84 A6
BSF
EECON1, WREN
CLRF
CLRF
CLRF
TBLPTRU
TBLPTRH
TBLPTRL
Step 2: Point to first row in code memory.
0000
0000
0000
6A F8
6A F7
6A F6
Step 3: Enable erase and erase single row.
0000
0000
0000
88 A6
82 A6
00 00
BSF
EECON1, FREE
BSF
EECON1, WR
NOP – hold PGC high for time P10.
Step 4: Repeat Step 3, with Address Pointer incremented by 1024, until all rows are erased.
FIGURE 3-3:
SET WR AND START ROW ERASE TIMING
P5
1
2
3
4
1
3
2
4
5
6
15
16
1
2
3
4
PGC
2
3
P10
P5A
P5
PGD
1
0
0
0
0
4-Bit Command
0
1
1
0
0
1
0
1
16-Bit Data Payload
0
0
0
0
0
4-Bit Command
Row-Erase Time
0
0
16-Bit
Data Payload
PGD = Input
DS30009687F-page 10
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
FIGURE 3-4:
SINGLE ROW ERASE CODE MEMORY FLOW
Start
Addr = 0
Configure
Device for
Row Erase
Start Erase Sequence
and Hold PGC High
for Time P10
Addr = Addr + 1024
No
All
Rows
Done?
Yes
Done
 2008-2015 Microchip Technology Inc.
DS30009687F-page 11
PIC18F2XJXX/4XJXX FAMILY
3.2
Code Memory Programming
Programming code memory is accomplished by first
loading data into the write buffer and then initiating a
programming sequence. The write buffer for all devices
in the PIC18F2XJXX/4XJXX Family is 64 bytes. It can
be mapped to any 64-byte block beginning at 000000h.
The actual memory write sequence takes the contents
of this buffer and programs the 64-byte block of code
memory indicated by the Table Pointer.
Write buffer locations are not cleared following a write
operation; the buffer retains its data after the write is
complete. This means that the buffer must be written
with 64 bytes on each operation. If there are locations
in the code memory that are to remain empty, the
corresponding locations in the buffer must be filled with
FFFFh. This avoids rewriting old data from the previous
cycle.
TABLE 3-3:
The programming duration is internally timed. After a
Start Programming command is issued (4-bit command, ‘1111’), a NOP is issued, where the 4th PGC is
held high for the duration of the programming time, P9.
The code sequence to program a PIC18F2XJXX/
4XJXX Family device is shown in Table 3-3. The
flowchart shown in Figure 3-5 depicts the logic
necessary to completely write a PIC18F2XJXX/4XJXX
Family device. The timing diagram that details the Start
Programming command and parameter P9 is shown in
Figure 3-6.
Note 1: The TBLPTR register must point to the
same region when initiating the
programming sequence as it did when
the write buffers were loaded.
WRITE CODE MEMORY CODE SEQUENCE
4-Bit
Command
Data Payload
Core Instruction
Step 1: Enable writes.
0000
84 A6
BSF
EECON1, WREN
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
<Addr[21:16]>
TBLPTRU
<Addr[15:8]>
TBLPTRH
<Addr[7:0]>
TBLPTRL
Step 2: Load write buffer.
0000
0000
0000
0000
0000
0000
0E
6E
0E
6E
0E
6E
<Addr[21:16]>
F8
<Addr[15:8]>
F7
<Addr[7:0]>
F6
Step 3: Repeat for all but the last two bytes. Any unused locations should be filled with FFFFh.
1101
<MSB><LSB>
Write 2 bytes and post-increment address by 2.
Step 4: Load write buffer for last two bytes.
1111
0000
<MSB><LSB>
00 00
Write 2 bytes and start programming.
NOP - hold PGC high for time P9.
To continue writing data, repeat Steps 2 through 4, where the Address Pointer is incremented by 2 at each iteration of the loop.
DS30009687F-page 12
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
FIGURE 3-5:
PROGRAM CODE MEMORY FLOW
Start
LoopCount = 0
Configure
Device for
Writes
Load 2 Bytes
to Write
Buffer at <Addr>
All
Bytes
Written?
No
LoopCount =
LoopCount + 1
Yes
Start Write Sequence
and Hold PGC
High Until Done
and Wait P9
All
Locations
Done?
No
Yes
Done
FIGURE 3-6:
TABLE WRITE AND START PROGRAMMING INSTRUCTION TIMING (1111)
P5
1
2
3
4
1
3
2
4
5
6
15
16
1
2
3
4
PGC
2
3
P9
P5A
P5
PGD
1
1
1
1
1
n
n
4-Bit Command
n
n
n
n
n
n
16-Bit Data Payload
0
0
0
0
4-Bit Command
0
Programming Time
0
0
16-Bit
Data Payload
PGD = Input
 2008-2015 Microchip Technology Inc.
DS30009687F-page 13
PIC18F2XJXX/4XJXX FAMILY
3.2.1
MODIFYING CODE MEMORY
The WREN bit must be set if the WR bit in EECON1 is
used to initiate a write sequence.
The previous programming example assumed that the
device had been Bulk Erased prior to programming. It
may be the case, however, that the user wishes to
modify only a section of an already programmed device.
3.2.2
As described in Section 4.2 “Verify Code Memory
and Configuration Word”, the appropriate number of
bytes required for the erase buffer must be read out of
code memory and buffered. Modifications can be made
on this buffer. Then, the block of code memory that was
read out must be erased and rewritten with the modified
data. The code sequence is shown in Table 3-4.
Since the Flash Configuration Words are stored in
program memory, they are programmed as if they were
program data. Refer to Section 3.2 “Code Memory
Programming” and Section 3.2.1 “Modifying Code
Memory” for methods and examples on programming
or modifying program memory. See also Section 5.0
“Configuration Word” for additional information on
the Configuration Words.
TABLE 3-4:
CONFIGURATION WORD
PROGRAMMING
MODIFYING CODE MEMORY
4-Bit
Command
Data Payload
Core Instruction
Step 1: Set the Table Pointer for the block to be erased.
0000
0000
0000
0000
0000
0000
0E
6E
0E
6E
0E
6E
<Addr[21:16]>
F8
<Addr[8:15]>
F7
<Addr[7:0]>
F6
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
<Addr[21:16]>
TBLPTRU
<Addr[8:15]>
TBLPTRH
<Addr[7:0]>
TBLPTRL
Step 2: Read and modify code memory (see Section 4.1 “Read Code Memory”).
Step 3: Enable memory writes and set up an erase.
0000
0000
84 A6
88 A6
BSF
BSF
EECON1, WREN
EECON1, FREE
Step 4: Initiate erase.
0000
0000
82 A6
00 00
BSF
EECON1, WR
NOP - hold PGC high for time P10.
Step 5: Load write buffer. The correct bytes will be selected based on the Table Pointer.
0000
0000
0000
0000
0000
0000
1101
.
.
.
1111
0000
0E <Addr[21:16]>
6E F8
0E <Addr[8:15]>
6E F7
0E <Addr[7:0]>
6E F6
<MSB><LSB>
.
.
.
<MSB><LSB>
00 00
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
Write 2
<Addr[21:16]>
TBLPTRU
<Addr[8:15]>
TBLPTRH
<Addr[7:0]>
TBLPTRL
bytes and post-increment address by 2.
Repeat write operation 30 more times to fill the write buffer
Write 2 bytes and start programming.
NOP - hold PGC high for time P9.
Step 6: Repeat Step 5 for a total of 16 times (if rewriting the entire 1024 bytes of the erase page size).
Step 7: To continue modifying data, repeat Steps 1 through 5, where the Address Pointer is incremented by 1024 bytes at each
iteration of the loop.
Step 8: Disable writes.
0000
94 A6
DS30009687F-page 14
BCF
EECON1, WREN
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
3.3
Endurance and Retention
To maintain the endurance specification of the Flash
program memory cells, each byte should never be
programmed more than once between erase operations.
Before attempting to modify the contents of a specific
byte of Flash memory a second time, an erase operation
(either a Bulk Erase or a Row Erase which includes that
byte) should be performed.
 2008-2015 Microchip Technology Inc.
DS30009687F-page 15
PIC18F2XJXX/4XJXX FAMILY
4.0
READING THE DEVICE
4.1
Read Code Memory
delay of P6 must be introduced after the falling edge of
the 8th PGC of the operand to allow PGD to transition
from an input to an output. During this time, PGC must
be held low (see Figure 4-1). This operation also
increments the Table Pointer by one, pointing to the
next byte in code memory for the next read.
Code memory is accessed one byte at a time via the
4-bit command, ‘1001’ (table read, post-increment).
The contents of memory pointed to by the Table Pointer
(TBLPTRU:TBLPTRH:TBLPTRL) are serially output on
PGD.
This technique will work to read any memory in the
000000h to 3FFFFFh address space, so it also applies
to reading the Configuration registers.
The 4-bit command is shifted in LSb first. The read is
executed during the next eight clocks, then shifted out
on PGD during the last eight clocks, LSb to MSb. A
TABLE 4-1:
READ CODE MEMORY SEQUENCE
4-Bit
Command
Data Payload
Core Instruction
Step 1: Set Table Pointer.
0000
0000
0000
0000
0000
0000
0E
6E
0E
6E
0E
6E
<Addr[21:16]>
F8
<Addr[15:8]>
F7
<Addr[7:0]>
F6
MOVLW
MOVWF
MOVLW
MOVWF
MOVLW
MOVWF
Addr[21:16]
TBLPTRU
<Addr[15:8]>
TBLPTRH
<Addr[7:0]>
TBLPTRL
Step 2: Read memory and then shift out on PGD, LSb to MSb.
1001
00 00
FIGURE 4-1:
1
TBLRD *+
TABLE READ, POST-INCREMENT INSTRUCTION TIMING (1001)
2
3
4
1
2
3
4
5
6
7
9
8
10
11
12
13
14
15
1
16
2
3
4
PGC
P5
P5A
P6
P14
PGD
1
0
0
LSb 1
1
2
3
4
5
Shift Data Out
PGD = Input
DS30009687F-page 16
PGD = Output
6
MSb
n
n
n
n
Fetch Next 4-Bit Command
PGD = Input
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
4.2
Verify Code Memory and
Configuration Word
4.3
The verify step involves reading back the code memory
space and comparing it against the copy held in the
programmer’s buffer. Because the Flash Configuration
Words are stored at the end of program memory, it is
verified with the rest of the code at this time.
The verify process is shown in the flowchart in
Figure 4-2. Memory reads occur a single byte at a time,
so two bytes must be read to compare against the word
in the programmer’s buffer. Refer to Section 4.1
“Read Code Memory” for implementation details of
reading code memory.
Note 1: Because the Flash Configuration Word
contains the device code protection bit,
code memory should be verified
immediately after writing if code protection
is enabled. This is because the device will
not be readable or verifiable if a device
Reset occurs after the Flash Configuration
Words (and the CP0 bit) have been
cleared.
FIGURE 4-2:
VERIFY CODE
MEMORY FLOW
Blank Check
The term Blank Check means to verify that the device
has no programmed memory cells. All memories, code
memory and Configuration bits, must be verified. The
Device ID registers (3FFFFEh:3FFFFFh) should be
ignored.
A “blank” or “erased” memory cell will read as a ‘1’, so
Blank Checking a device merely means to verify that all
bytes read as FFh. The overall process flow is shown
in Figure 4-3.
Blank Checking is merely code verification with FFh
expect data. For implementation details, refer to
Section 4.2 “Verify Code Memory and Configuration
Word”.
FIGURE 4-3:
BLANK CHECK FLOW
Start
Blank Check Device
Is
Device
Blank?
Yes
Continue
No
Start
Abort
Set TBLPTR = 0
Read Low Byte
with Post-Increment
Read High Byte
with Post-Increment
Does
Word = Expect
Data?
No
Failure,
Report
Error
Yes
No
All
Code Memory
Verified?
Yes
Done
 2008-2015 Microchip Technology Inc.
DS30009687F-page 17
PIC18F2XJXX/4XJXX FAMILY
5.0
CONFIGURATION WORD
TABLE 5-1:
The Configuration Words of the PIC18F2XJXX/4XJXX
Family devices are implemented as volatile memory
registers. All of the Configuration registers (CONFIG1L,
CONFIG1H, CONFIG2L, CONFIG2H, CONFIG3L,
CONFIG3H, CONFIG4L, and CONFIG4H) are
automatically loaded following each device Reset.
Configuration
Register
The data for these registers is taken from the four Flash
Configuration Words located at the end of program
memory. Configuration data is stored in order, starting
with CONFIG1L in the lowest Flash address and
ending with CONFIG4H in the highest. The mapping to
specific Configuration Words is shown in Table 5-1.
Users should always reserve these locations for
Configuration Word data and write their application
code accordingly.
Flash
Configuration
Byte(1)
Configuration
Register
Address
CONFIG1L
XFF8h
300000h
CONFIG1H
XFF9h
300001h
CONFIG2L
XFFAh
300002h
CONFIG2H
XFFBh
300003h
CONFIG3L
XFFCh
300004h
CONFIG3H
XFFDh
300005h
CONFIG4L(2)
XFFEh
300006h
(2)
XFFFh
300007h
CONFIG4H
The upper four bits of each Flash Configuration Word
should always be stored in program memory as ‘1111’.
This is done so these program memory addresses will
always be ‘1111 xxxx xxxx xxxx’ and interpreted
as a NOP instruction if they were ever to be executed.
Because the corresponding bits in the Configuration
registers are unimplemented, they will not change the
device’s configuration.
MAPPING OF THE FLASH
CONFIGURATION WORDS TO
THE CONFIGURATION
REGISTERS
Note 1:
2:
See Table 2-2 for the complete addresses
within code space for specific devices and
memory sizes.
Unimplemented in PIC18F45J10 family
devices.
The Configuration and Device ID registers are
summarized in Table 5-2. A listing of the individual
Configuration bits and their options is provided in
Table 5-3.
TABLE 5-2:
PIC18F45J10 FAMILY DEVICES: CONFIGURATION BITS AND DEVICE IDs
File Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Default/
Unprogrammed
Value
300000h
CONFIG1L
DEBUG
XINST
STVREN
—
—
—
—
WDTEN
111- ---1
300001h
CONFIG1H
—(1)
—(1)
—(1)
—(1)
—(2)
CP0
—
—
---- 01--
300002h
CONFIG2L
IESO
FCMEN
—
—
—
FOSC2
FOSC1
FOSC0
300003h
CONFIG2H
—(1)
—(1)
—(1)
—(1)
WDTPS3
300005h
CONFIG3H
—(1)
—(1)
—(1)
—(1)
—
—
—
CCP2MX
---- ---1
DEV2
DEV1
DEV0
REV4
REV3
REV2
REV1
REV0
See Table
DEV10
DEV9
DEV8
DEV7
DEV6
DEV5
DEV4
DEV3
See Table
3FFFFEh DEVID1(3)
(3)
3FFFFFh DEVID2
Legend:
Note 1:
2:
3:
WDTPS2 WDTPS1 WDTPS0
11-- -111
---- 1111
- = unimplemented. Shaded cells are unimplemented, read as ‘0’.
The value of these bits in program memory should always be ‘1’. This ensures that the location is executed as a NOP if
it is accidentally executed.
This bit should always be maintained at ‘0’.
DEVID registers are read-only and cannot be programmed by the user.
DS30009687F-page 18
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
TABLE 5-3:
Bit Name
PIC18F45J10 FAMILY DEVICES: BIT DESCRIPTIONS
Configuration
Words
Description
DEBUG
CONFIG1L
Background Debugger Enable bit
1 = Background debugger disabled, RB6 and RB7 configured as general
purpose I/O pins
0 = Background debugger enabled, RB6 and RB7 are dedicated to in-circuit debug
XINST
CONFIG1L
Extended Instruction Set Enable bit
1 = Instruction set extension and Indexed Addressing mode enabled
0 = Instruction set extension and Indexed Addressing mode disabled
(Legacy mode)
STVREN
CONFIG1L
Stack Overflow/Underflow Reset Enable bit
1 = Reset on stack overflow/underflow enabled
0 = Reset on stack overflow/underflow disabled
WDTEN
CONFIG1L
Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled (control is placed on SWDTEN bit)
CP0
CONFIG1H
Code Protection bit
1 = Program memory is not code-protected
0 = Program memory is code-protected
IESO
CONFIG2L
Internal/External Oscillator Switchover bit
1 = Oscillator Switchover mode enabled
0 = Oscillator Switchover mode disabled
FCMEN
CONFIG2L
Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor enabled
0 = Fail-Safe Clock Monitor disabled
FOSC2
CONFIG2L
Default Oscillator Select bit
1 = Clock designated by FOSC<1:0> is enabled as system clock when
OSCCON<1:0> = 00
0 = INTRC is enabled as system clock when OSCCON<1:0> = 00
FOSC<1:0>
CONFIG2L
Primary Oscillator Select bits
11 = EC oscillator, PLL enabled and under software control, CLKO function on OSC2
10 = EC oscillator, CLKO function on OSC2
01 = HS oscillator, PLL enabled and under software control
00 = HS oscillator
WDTPS<3:0>
CONFIG2H
Watchdog Timer Postscale Select bits
1111 = 1:32,768
1110 = 1:16,384
1101 = 1:8,192
1100 = 1:4,096
1011 = 1:2,048
1010 = 1:1,024
1001 = 1:512
1000 = 1:256
0111 = 1:128
0110 = 1:64
0101 = 1:32
0100 = 1:16
0011 = 1:8
0010 = 1:4
0001 = 1:2
0000 = 1:1
CCP2MX
CONFIG3H
CCP2 MUX bit
1 = CCP2 is multiplexed with RC1
0 = CCP2 is multiplexed with RB3
 2008-2015 Microchip Technology Inc.
DS30009687F-page 19
PIC18F2XJXX/4XJXX FAMILY
TABLE 5-4:
PIC18F46J11 AND PIC18F46J50 FAMILY DEVICES: CONFIGURATION BITS AND
DEVICE IDs
File Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
300000h CONFIG1L
DEBUG
XINST
STVREN
—
300001h CONFIG1H
—(2)
—(2)
—(2)
—(2)
300002h CONFIG2L
IESO
FCMEN
—
LPT1OSC
T1DIG
FOSC2
300003h CONFIG2H
—(2)
—(2)
—(2)
—(2)
WDTPS3
WDTPS2
Bit 1
PLLDIV2(3) PLLDIV1(3) PLLDIV0(3)
—(4)
CP0
Default/
Unprogrammed
Value(1)
WDTEN
111- 1111
CPDIV0(3)
---- 0111
FOSC1
FOSC0
11-1 1111
WDTPS1
WDTPS0
---- 1111
RTCOSC
DSWDTOSC
1111 1111
CPDIV1(3)
300004h CONFIG3L DSWDTPS3 DSWDTPS2 DSWDTPS1 DSWDTPS0 DSWDTEN DSBOREN
Bit 0
300005h CONFIG3H
—(2)
—(2)
—(2)
—(2)
MSSPMSK
—
—
IOL1WAY
---- 1--1
300006h CONFIG4L
WPCFG
WPEND
WPFP5(5)
WPFP4(6)
WPFP3
WPFP2
WPFP1
WPFP0
1111 1111
300007h CONFIG4H
—(2)
—(2)
—(2)
—(2)
—
—
—
WPDIS
---- ---1
3FFFFEh DEVID1
DEV2
DEV1
DEV0
REV4
REV3
REV2
REV1
REV0
xxxx xxxx
3FFFFFh DEVID2
DEV10
DEV9
DEV8
DEV7
DEV6
DEV5
DEV4
DEV3
0100 00xx
Legend:
Note 1:
2:
3:
4:
5:
6:
x = unknown, u = unchanged, - = unimplemented. Shaded cells are unimplemented, read as ‘0’.
Values reflect the unprogrammed state as received from the factory and following Power-on Resets. In all other Reset states, the
configuration bytes maintain their previously programmed states.
The value of these bits in program memory should always be ‘1’. This ensures that the location is executed as a NOP if it is
accidentally executed.
These bits are not implemented in PIC18F46J11 family devices.
This bit should always be maintained at ‘0’.
This bit is not available on 32K and 16K memory devices (X4J11, X4J50, X5J11, and X5J50 devices) and should always be
maintained at ‘0’ on those devices.
This bit is not available on 16K memory devices (X4J11 and X4J50 devices) and should always be maintained at ‘0’ on those
devices.
TABLE 5-5:
PIC18F46J11 AND PIC18F46J50 FAMILY DEVICES: BIT DESCRIPTIONS
Bit Name
Configuration
Words
Description
DEBUG
CONFIG1L
Background Debugger Enable bit
1 = Background debugger disabled, RB6 and RB7 configured as general purpose
I/O pins
0 = Background debugger enabled, RB6 and RB7 are dedicated to in-circuit debug
XINST
CONFIG1L
Enhanced Instruction Set Enable bit
1 = Instruction set extension and Indexed Addressing mode enabled
0 = Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
STVREN
CONFIG1L
Stack Overflow/Underflow Reset Enable bit
1 = Reset on stack overflow/underflow enabled
0 = Reset on stack overflow/underflow disabled
PLLDIV<2:0>(3)
CONFIG1L
PLL Input Divider bits
Divider must be selected to provide a 4 MHz input into the 96 MHz PLL.
111 = No divide – oscillator used directly (4 MHz input)
110 = Oscillator divided by 2 (8 MHz input)
101 = Oscillator divided by 3 (12 MHz input)
100 = Oscillator divided by 4 (16 MHz input)
011 = Oscillator divided by 5 (20 MHz input)
010 = Oscillator divided by 6 (24 MHz input)
001 = Oscillator divided by 10 (40 MHz input)
000 = Oscillator divided by 12 (48 MHz input)
WDTEN
CONFIG1L
Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled (control is placed on SWDTEN bit)
Note 1:
2:
3:
4:
The Configuration bits can only be programmed indirectly by programming the Flash Configuration Word.
The Configuration bits are reset to ‘1’ only on VDD Reset; it is reloaded with the programmed value at any device Reset.
These bits are not implemented in PIC18F46J11 family devices.
Once this bit is cleared, all the Configuration registers which reside in the last page are also protected. To disable code
protection, perform an ICSP™ Bulk Erase operation.
DS30009687F-page 20
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
TABLE 5-5:
Bit Name
PIC18F46J11 AND PIC18F46J50 FAMILY DEVICES: BIT DESCRIPTIONS (CONTINUED)
Configuration
Words
Description
CP0(4)
CONFIG1H
Code Protection bit
1 = Program memory is not code-protected
0 = Program memory is code-protected
CPDIV<1:0>(3)
CONFIG1H
CPU System Clock Selection bits
11 = No CPU system clock divide
10 = CPU system clock divided by 2
01 = CPU system clock divided by 3
00 = CPU system clock divided by 6
IESO
CONFIG2L(1,2)
Two-Speed Start-up (Internal/External Oscillator Switchover) Control bit
1 = Oscillator Switchover mode enabled
0 = Oscillator Switchover mode disabled
FCMEN
CONFIG2L(1,2)
Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor enabled
0 = Fail-Safe Clock Monitor disabled
LPT1OSC
CONFIG2L(1,2)
Low-Power Timer1 Oscillator Enable bit
1 = Timer1 oscillator configured for low-power operation
0 = Timer1 oscillator configured for higher-power operation
T1DIG
CONFIG2L(1,2)
Secondary Clock Source T1OSCEN Enforcement bit(1)
1 = Secondary oscillator clock source may be selected (OSCCON <1:0> = 01)
regardless of T1OSCEN state
0 = Secondary oscillator clock source may not be selected unless T1CON <3> = 1
FOSC<2:0>
CONFIG2L(1,2)
Oscillator Selection bits
111 =EC+PLL (S/W controlled by PLLEN bit), CLKO on RA6
110 =EC oscillator (PLL always disabled) with CLKO on RA6
101 =HS+PLL (S/W controlled by PLLEN bit)
100 =HS oscillator (PLL always disabled)
011 =INTOSCPLLO, internal oscillator with PLL (S/W controlled by PLLEN bit), CLKO on
RA6, port function on RA7
010 =INTOSCPLL, internal oscillator with PLL (S/W controlled by PLLEN bit), port
function on RA6 and RA7
001 =INTOSCO, internal oscillator, INTOSC or INTRC (PLL always disabled), CLKO on
RA6, port function on RA7
000 =INTOSC, internal oscillator INTOSC or INTRC (PLL always disabled), port function
on RA6 and RA7
WDTPS<3:0>
CONFIG2H(1,2)
Watchdog Timer Postscale Select bits
1111 = 1:32,768
1110 = 1:16,384
1101 = 1:8,192
1100 = 1:4,096
1011 = 1:2,048
1010 = 1:1,024
1001 = 1:512
1000 = 1:256
0111 = 1:128
0110 = 1:64
0101 = 1:32
0100 = 1:16
0011 = 1:8
0010 = 1:4
0001 = 1:2
0000 = 1:1
Note 1:
2:
3:
4:
The Configuration bits can only be programmed indirectly by programming the Flash Configuration Word.
The Configuration bits are reset to ‘1’ only on VDD Reset; it is reloaded with the programmed value at any device Reset.
These bits are not implemented in PIC18F46J11 family devices.
Once this bit is cleared, all the Configuration registers which reside in the last page are also protected. To disable code
protection, perform an ICSP™ Bulk Erase operation.
 2008-2015 Microchip Technology Inc.
DS30009687F-page 21
PIC18F2XJXX/4XJXX FAMILY
TABLE 5-5:
PIC18F46J11 AND PIC18F46J50 FAMILY DEVICES: BIT DESCRIPTIONS (CONTINUED)
Bit Name
Configuration
Words
Description
DSWTPS<3:0>
CONFIG3L
Deep Sleep Watchdog Timer Postscale Select bits
The DSWDT prescaler is 32; this creates an approximate base time unit of 1 ms.
1111 = 1:2,147,483,648 (25.7 days)
1110 = 1:536,870,912 (6.4 days)
1101 = 1:134,217,728 (38.5 hours)
1100 = 1:33,554,432 (9.6 hours)
1011 = 1:8,388,608 (2.4 hours)
1010 = 1:2,097,152 (36 minutes)
1001 = 1:524,288 (9 minutes)
1000 = 1:131,072 (135 seconds)
0111 = 1:32,768 (34 seconds)
0110 = 1:8,192 (8.5 seconds)
0101 = 1:2,048 (2.1 seconds)
0100 = 1:512 (528 ms)
0011 = 1:128 (132 ms)
0010 = 1:32 (33 ms)
0001 = 1:8 (8.3 ms)
0000 = 1:2 (2.1 ms)
DSWDTEN
CONFIG3L
Deep Sleep Watchdog Timer Enable bit
1 = DSWDT enabled
0 = DSWDT disabled
DSBOREN
CONFIG3L
Deep Sleep BOR Enable bit
1 = BOR enabled in Deep Sleep
0 = BOR disabled in Deep Sleep (does not affect operation in non Deep Sleep modes)
RTCOSC
CONFIG3L
RTCC Reference Clock Select bit
1 = RTCC uses T1OSC/T1CKI as reference clock
0 = RTCC uses INTRC as reference clock
DSWDTOSC
CONFIG3L
DSWDT Reference Clock Select bit
1 = DSWDT uses INTRC as reference clock
0 = DSWDT uses T1OSC/T1CKI as reference clock
MSSPMSK(1,2)
CONFIG3H
MSSP 7-Bit Address Masking Mode Enable bit
1 = 7-Bit Address Masking mode enable
0 = 5-Bit Address Masking mode enable
IOL1WAY
CONFIG3H
IOLOCK Bit One-Way Set Enable bit
1 = The IOLOCK bit (PPSCON<0>) can be set once, provided the unlock sequence has
been completed. Once set, the Peripheral Pin Select registers cannot be written to a
second time.
0 = The IOLOCK bit (PPSCON<0>) can be set and cleared as needed, provided the
unlock sequence has been completed.
WPCFG(4)
CONFIG4L
Write/Erase Protect Configuration Words Page bit (valid when WPDIS = 0)
1 = Configuration Words page is not erase/write-protected unless WPEND and
WPFP<5:0> settings include the Configuration Words page
0 = Configuration Words page is erase/write-protected, regardless of WPEND and
WPFP<5:0> settings
WPEND
CONFIG4L
Write/Erase Protect Region Select bit (valid when WPDIS = 0)
1 = Flash pages, WPFP<5:0> to Configuration Words page, are write/erase-protected
0 = Flash pages, 0 to WPFP<5:0> are write/erase-protected
Note 1:
2:
3:
4:
The Configuration bits can only be programmed indirectly by programming the Flash Configuration Word.
The Configuration bits are reset to ‘1’ only on VDD Reset; it is reloaded with the programmed value at any device Reset.
These bits are not implemented in PIC18F46J11 family devices.
Once this bit is cleared, all the Configuration registers which reside in the last page are also protected. To disable code
protection, perform an ICSP™ Bulk Erase operation.
DS30009687F-page 22
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
TABLE 5-5:
Bit Name
PIC18F46J11 AND PIC18F46J50 FAMILY DEVICES: BIT DESCRIPTIONS (CONTINUED)
Configuration
Words
Description
WPFP<5:0>
CONFIG4L
Write/Erase Protect Page Start/End Location bits
Used with WPEND bit to define which pages in Flash will be write/erase-protected.
WPDIS
CONFIG4H
Write Protect Disable bit
1 = WPFP<5:0>, WPEND and WPCFG bits ignored; all Flash memory may be erased or
written
0 = WPFP<5:0>, WPEND and WPCFG bits enabled; write/erase-protect active for the
selected region(s)
DEV<2:0>
DEVID1
Device ID bits
Used with the DEV<10:3> bits in the Device ID Register 2 to identify the part number.
REV<4:0>
DEVID1
Revision ID bits
Indicate the device revision.
DEV<10:3>
DEVID2
Device ID bits
Used with the DEV<2:0> bits in the Device ID Register 1 to identify the part number.
Note 1:
2:
3:
4:
The Configuration bits can only be programmed indirectly by programming the Flash Configuration Word.
The Configuration bits are reset to ‘1’ only on VDD Reset; it is reloaded with the programmed value at any device Reset.
These bits are not implemented in PIC18F46J11 family devices.
Once this bit is cleared, all the Configuration registers which reside in the last page are also protected. To disable code
protection, perform an ICSP™ Bulk Erase operation.
TABLE 5-6:
PIC18F47J13 AND PIC18F47J53 FAMILY DEVICES: CONFIGURATION BITS AND
DEVICE IDs
File Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Default/
Unprogrammed
Value(1)
300000h CONFIG1L
DEBUG
XINST
STVREN
CFGPLLEN
PLLDIV2
PLLDIV1
PLLDIV0
WDTEN
111- 1111
300001h CONFIG1H
—(2)
—(2)
—(2)
—(2)
—(4)
CP0
CPDIV1(3)
CPDIV0(3)
---- 0111
300002h CONFIG2L
IESO
FCMEN
CLKOEC
300003h CONFIG2H
—(2)
—(2)
—(2)
SOSCSEL1 SOSCSEL0
—(2)
WDTPS3
FOSC2
FOSC1
FOSC0
1111 1111
WDTPS2
WDTPS1
WDTPS0
---- 1111
RTCOSC
DSWDTOSC
1111 1111
ADCSEL
IOL1WAY
---- 1111
300004h CONFIG3L DSWDTPS3 DSWDTPS2 DSWDTPS1 DSWDTPS0 DSWDTEN DSBOREN
300005h CONFIG3H
—(2)
—(2)
—(2)
—(2)
300006h CONFIG4L
WPCFG
WPFP6
WPFP5
300007h CONFIG4H
—(2)
—(2)
—(2)
3FFFFEh DEVID1
DEV2
DEV1
3FFFFFh DEVID2
DEV10
DEV9
Legend:
Note 1:
2:
3:
4:
MSSPMSK
PLLSEL
WPFP4
WPFP3
WPFP2
WPFP1
WPFP0
1111 1111
—(2)
LS48MHZ(3)
—
WPEND
WPDIS
---- 1-11
DEV0
REV4
REV3
REV2
REV1
REV0
xxxx xxxx
DEV8
DEV7
DEV6
DEV5
DEV4
DEV3
0101 10xx
x = unknown, u = unchanged, - = unimplemented. Shaded cells are unimplemented, read as ‘0’.
Values reflect the unprogrammed state as received from the factory and following Power-on Resets. In all other Reset states, the
configuration bytes maintain their previously programmed states.
The value of these bits in program memory should always be ‘1’. This ensures that the location is executed as a NOP if it is
accidentally executed.
These bits are not implemented in PIC18F47J13 family devices.
This bit should always be maintained at ‘0’.
 2008-2015 Microchip Technology Inc.
DS30009687F-page 23
PIC18F2XJXX/4XJXX FAMILY
TABLE 5-7:
PIC18F47J13 AND PIC18F47J53 FAMILY DEVICES: BIT DESCRIPTIONS
Bit Name
Configuration
Words
Description
DEBUG
CONFIG1L
Background Debugger Enable bit
1 = Background debugger disabled, RB6 and RB7 configured as general purpose
I/O pins
0 = Background debugger enabled, RB6 and RB7 are dedicated to in-circuit debug
XINST
CONFIG1L
Enhanced Instruction Set Enable bit
1 = Instruction set extension and Indexed Addressing mode enabled
0 = Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
STVREN
CONFIG1L
Stack Overflow/Underflow Reset Enable bit
1 = Reset on stack overflow/underflow enabled
0 = Reset on stack overflow/underflow disabled
CFGPLLEN
CONFIG1L
Enable PLL on Start-up bit
1 = PLL enabled on start-up. Not recommended for low-voltage designs.
0 = PLL disabled on start-up. Firmware may later enable PLL through OSCTUNE<6>.
PLLDIV<2:0>
CONFIG1L
96 MHz PLL Input Divider bits
Divider must be selected to provide a 4 MHz input into the 96 MHz PLL.
111 =No divide – oscillator used directly (4 MHz input)
110 =Oscillator divided by 2 (8 MHz input)
101 =Oscillator divided by 3 (12 MHz input)
100 =Oscillator divided by 4 (16 MHz input)
011 =Oscillator divided by 5 (20 MHz input)
010 =Oscillator divided by 6 (24 MHz input)
001 =Oscillator divided by 10 (40 MHz input)
000 =Oscillator divided by 12 (48 MHz input)
WDTEN
CONFIG1L
Watchdog Timer Enable bit
1 = WDT enabled
0 = WDT disabled (control is placed on the SWDTEN bit)
CP0(4)
CONFIG1H
Code Protection bit
1 = Program memory is not code-protected
0 = Program memory is code-protected
CPDIV<1:0>(3)
CONFIG1H
CPU System Clock Selection bits
11 = No CPU system clock divide
10 = CPU system clock divided by 2
01 = CPU system clock divided by 3
00 = CPU system clock divided by 6
IESO
CONFIG2L(1,2)
Two-Speed Start-up (Internal/External Oscillator Switchover) Control bit
1 = Oscillator Switchover mode enabled
0 = Oscillator Switchover mode disabled
FCMEN
CONFIG2L(1,2)
Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor enabled
0 = Fail-Safe Clock Monitor disabled
CLKOEC
CONFIG2L
EC Mode Clock Output Enable bit
1 = CLKO output signal active on the RA6 pin (EC mode only)
0 = CLKO output disabled
SOSCSEL<1:0>
CONFIG2L
Secondary Oscillator Circuit Selection bits
11 = High-power SOSC circuit selected
10 = Digital Input mode (SCLKI)
01 = Low-power SOSC circuit selected
00 = Reserved
Note 1:
2:
3:
4:
5:
The Configuration bits can only be programmed indirectly by programming the Flash Configuration Word.
The Configuration bits are reset to ‘1’ only on VDD Reset; it is reloaded with the programmed value at any device Reset.
These bits are not implemented in PIC18F47J13 family devices.
Once this bit is cleared, all the Configuration registers which reside in the last page are also protected. To disable code
protection, perform an ICSP™ Bulk Erase operation.
Not implemented on PIC18F47J53 family devices.
DS30009687F-page 24
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
TABLE 5-7:
Bit Name
PIC18F47J13 AND PIC18F47J53 FAMILY DEVICES: BIT DESCRIPTIONS (CONTINUED)
Configuration
Words
Description
FOSC<2:0>
CONFIG2L(1,2)
Oscillator Selection bits
111 =EC+PLL (S/W controlled by PLLEN bit), CLKO on RA6
110 =EC oscillator (PLL always disabled) with CLKO on RA6
101 =HS+PLL (S/W controlled by PLLEN bit)
100 =HS oscillator (PLL always disabled)
011 =INTOSCPLLO, internal oscillator with PLL (S/W controlled by PLLEN bit), CLKO on
RA6, port function on RA7
010 =INTOSCPLL, internal oscillator with PLL (S/W controlled by PLLEN bit), port
function on RA6 and RA7
001 =INTOSCO, internal oscillator, INTOSC or INTRC (PLL always disabled), CLKO on
RA6, port function on RA7
000 =INTOSC, internal oscillator INTOSC or INTRC (PLL always disabled), port function
on RA6 and RA7
WDTPS<3:0>
CONFIG2H(1,2)
Watchdog Timer Postscale Select bits
1111 = 1:32,768
1110 = 1:16,384
1101 = 1:8,192
1100 = 1:4,096
1011 = 1:2,048
1010 = 1:1,024
1001 = 1:512
1000 = 1:256
0111 = 1:128
0110 = 1:64
0101 = 1:32
0100 = 1:16
0011 = 1:8
0010 = 1:4
0001 = 1:2
0000 = 1:1
DSWTPS<3:0>
CONFIG3L
Deep Sleep Watchdog Timer Postscale Select bits
The DSWDT prescaler is 32; this creates an approximate base time unit of 1 ms.
1111 = 1:2,147,483,648 (25.7 days)
1110 = 1:536,870,912 (6.4 days)
1101 = 1:134,217,728 (38.5 hours)
1100 = 1:33,554,432 (9.6 hours)
1011 = 1:8,388,608 (2.4 hours)
1010 = 1:2,097,152 (36 minutes)
1001 = 1:524,288 (9 minutes)
1000 = 1:131,072 (135 seconds)
0111 = 1:32,768 (34 seconds)
0110 = 1:8,192 (8.5 seconds)
0101 = 1:2,048 (2.1 seconds)
0100 = 1:512 (528 ms)
0011 = 1:128 (132 ms)
0010 = 1:32 (33 ms)
0001 = 1:8 (8.3 ms)
0000 = 1:2 (2.1 ms)
DSWDTEN
CONFIG3L
Deep Sleep Watchdog Timer Enable bit
1 = DSWDT enabled
0 = DSWDT disabled
DSBOREN
CONFIG3L
Deep Sleep BOR Enable bit
1 = BOR enabled in Deep Sleep
0 = BOR disabled in Deep Sleep (does not affect operation in non Deep Sleep modes)
Note 1:
2:
3:
4:
5:
The Configuration bits can only be programmed indirectly by programming the Flash Configuration Word.
The Configuration bits are reset to ‘1’ only on VDD Reset; it is reloaded with the programmed value at any device Reset.
These bits are not implemented in PIC18F47J13 family devices.
Once this bit is cleared, all the Configuration registers which reside in the last page are also protected. To disable code
protection, perform an ICSP™ Bulk Erase operation.
Not implemented on PIC18F47J53 family devices.
 2008-2015 Microchip Technology Inc.
DS30009687F-page 25
PIC18F2XJXX/4XJXX FAMILY
TABLE 5-7:
PIC18F47J13 AND PIC18F47J53 FAMILY DEVICES: BIT DESCRIPTIONS (CONTINUED)
Bit Name
Configuration
Words
Description
RTCOSC
CONFIG3L
RTCC Reference Clock Select bit
1 = RTCC uses T1OSC/T1CKI as reference clock
0 = RTCC uses INTRC as reference clock
DSWDTOSC
CONFIG3L
DSWDT Reference Clock Select bit
1 = DSWDT uses INTRC as reference clock
0 = DSWDT uses T1OSC/T1CKI as reference clock
MSSPMSK(1,2)
CONFIG3H
MSSP 7-Bit Address Masking Mode Enable bit
1 = 7-Bit Address Masking mode enable
0 = 5-Bit Address Masking mode enable
PLLSEL(5)
CONFIG3H
PLL Selection bit
1 = 4x PLL selected
0 = 96 MHz PLL selected
ADCSEL
CONFIG3H
ADC Mode Selection bit
1 = 10-Bit ADC mode selected
0 = 12-Bit ADC mode selected
IOL1WAY
CONFIG3H
IOLOCK Bit One-Way Set Enable bit
1 = The IOLOCK bit (PPSCON<0>) can be set once, provided the unlock sequence has
been completed. Once set, the Peripheral Pin Select registers cannot be written to a
second time.
0 = The IOLOCK bit (PPSCON<0>) can be set and cleared as needed, provided the
unlock sequence has been completed
WPCFG
CONFIG4L
Write/Erase Protect Configuration Words Page bit (valid when WPDIS = 0)
1 = Configuration Words page is not erase/write-protected unless WPEND and
WPFP<6:0> settings include the Configuration Words page
0 = Configuration Words page is erase/write-protected, regardless of WPEND and
WPFP<6:0>
WPFP<6:0>
CONFIG4L
Write/Erase Protect Page Start/End Location bits
Used with WPEND bit to define which pages in Flash will be write/erase-protected.
WPEND
CONFIG4H
Write/Erase Protect Region Select bit (valid when WPDIS = 0)
1 = Flash pages, WPFP<6:0> to Configuration Words page, are write/erase-protected
0 = Flash pages, 0 to WPFP<6:0> are write/erase-protected
WPDIS
CONFIG4H
Write Protect Disable bit
1 = WPFP<6:0>, WPEND and WPCFG bits ignored; all Flash memory may be erased or
written
0 = WPFP<6:0>, WPEND and WPCFG bits enabled; write/erase-protect active for the
selected region(s)
LS48MHZ(3)
CONFIG4H
System Clock Selection bit
1 = System clock is expected at 48 MHz, FS/LS USB CLKEN’s divide-by is set to 8
0 = System clock is expected at 24 MHz, FS/LS USB CLKEN’s divide-by is set to 4
DEV<2:0>
DEVID1
Device ID bits
Used with the DEV<10:3> bits in the Device ID Register 2 to identify the part number.
REV<4:0>
DEVID1
Revision ID bits
Indicate the device revision.
DEV<10:3>
DEVID2
Device ID bits
Used with the DEV<2:0> bits in the Device ID Register 1 to identify the part number.
Note 1:
2:
3:
4:
5:
The Configuration bits can only be programmed indirectly by programming the Flash Configuration Word.
The Configuration bits are reset to ‘1’ only on VDD Reset; it is reloaded with the programmed value at any device Reset.
These bits are not implemented in PIC18F47J13 family devices.
Once this bit is cleared, all the Configuration registers which reside in the last page are also protected. To disable code
protection, perform an ICSP™ Bulk Erase operation.
Not implemented on PIC18F47J53 family devices.
DS30009687F-page 26
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
5.1
TABLE 5-8: DEVICE ID VALUE (CONTINUED)
Device ID Word
The Device ID Word for the PIC18F2XJXX/4XJXX
Family devices is located at 3FFFFEh:3FFFFFh.
These read-only bits may be used by the programmer
to identify what device type is being programmed and
read out normally, even after code protection has been
enabled. The process for reading the Device IDs is
shown in Figure 5-1. A complete list of Device ID
values for the PIC18F2XJXX/4XJXX Family is
presented in Table 5-8.
FIGURE 5-1:
READ DEVICE ID WORD FLOW
Start
Set TBLPTR = 3FFFFE
Read Low Byte
with Post-Increment
Read High Byte
with Post-Increment
Done
TABLE 5-8: DEVICE ID VALUE
Device ID Value
Device
Device ID Value
Device
DEVID2
DEVID1
PIC18F46J50
4Ch
101x xxxx
PIC18LF2450
4Ch
110x xxxx
PIC18LF25J50
4Ch
111x xxxx
PIC18LF26J50
4Dh
000x xxxx
PIC18LF44J50
4Dh
001x xxxx
PIC18LF45J50
4Dh
010x xxxx
PIC18LF46J50
4Dh
011x xxxx
PIC18LF24J11
4Eh
010x xxxx
PIC18LF25J11
4Eh
011x xxxx
PIC18LF26J11
4Eh
100x xxxx
PIC18LF44J11
4Eh
101x xxxx
PIC18LF45J11
4Eh
110x xxxx
PIC18LF46J11
4Eh
111x xxxx
PIC18F26J13
59h
001x xxxx
PIC18F27J13
59h
011x xxxx
PIC18F46J13
59h
101x xxxx
PIC18F47J13
59h
111x xxxx
PIC18LF26J13
5Bh
001x xxxx
PIC18LF27J13
5Bh
011x xxxx
PIC18LF46J13
5Bh
101x xxxx
PIC18LF47J13
5Bh
111x xxxx
PIC18F26J53
58h
001x xxxx
PIC18F27J53
58h
011x xxxx
DEVID2
DEVID1
PIC18F46J53
58h
101x xxxx
PIC18F24J10
1Dh
000x xxxx
PIC18F47J53
58h
111x xxxx
PIC18F25J10
1Ch
000x xxxx
PIC18LF26J53
5Ah
001x xxxx
PIC18F44J10
1Dh
001x xxxx
PIC18LF27J53
5Ah
011x xxxx
PIC18F45J10
1Ch
001x xxxx
PIC18LF46J53
5Ah
101x xxxx
PIC18LF24J10
1Dh
010x xxxx
PIC18LF47J53
5Ah
111x xxxx
PIC18LF25J10
1Ch
010x xxxx
PIC18LF44J10
1Dh
011x xxxx
5.2
PIC18LF45J10
1Ch
011x xxxx
PIC18F25J11
4Dh
101x xxxx
PIC18F24J11
4Dh
100x xxxx
PIC18F26J11
4Dh
110x xxxx
The checksum is calculated by summing the contents of
all code memory locations and the device Configuration
Words, appropriately masked. The Least Significant
16 bits of this sum are the checksum.
PIC18F45J11
4Eh
000x xxxx
PIC18F44J11
4Dh
111x xxxx
PIC18F46J11
4Eh
001x xxxx
PIC18F24J50
4Ch
000x xxxx
PIC18F25J50
4Ch
001x xxxx
PIC18F26J50
4Ch
010x xxxx
PIC18F44J50
4Ch
011x xxxx
PIC18F45J50
4Ch
100x xxxx
 2008-2015 Microchip Technology Inc.
Checksum Computation
The checksum calculation differs depending on
whether or not code protection is enabled. Since the
code memory locations read out differently depending
on the code-protect setting, the table describes how to
manipulate the actual code memory values to simulate
the values that would be read from a protected device.
When calculating a checksum by reading a device, the
entire code memory can simply be read and summed.
The Configuration Words can always be read.
DS30009687F-page 27
PIC18F2XJXX/4XJXX FAMILY
Table 5-9 describes how to calculate the checksum for
each device.
TABLE 5-9:
Device
CHECKSUM COMPUTATION
Code
Protection
Checksum
Off
SUM[000000:003FF7] + ([003FF8] & E1h) + ([003FF9] & 04h) + ([003FFA] & C7h) +
([003FFB] & 0Fh) + ([003FFD] & 01h)
PIC18F24J10
PIC18F44J10
0000h
SUM[000000:003FF7] + ([003FF8] & E1h) + ([003FF9] & FCh) + ([003FFA] & DFh) +
Off
([003FFB] & FFh) + ([003FFC] & FFh) + ([003FFD] & F9h) + ([003FFE] & FFh) +
PIC18F24J11
([003FFF] & F1h)
PIC18F44J11
On
0000h
SUM[000000:003FF7] + ([003FF8] & EFh) + ([003FF9] & FFh) + ([003FFA] & DFh) +
Off
([003FFB] & FFh) + ([003FFC] & FFh) + ([003FFD] & F9h) + ([003FFE] & FFh) +
PIC18F24J50
([003FFF] & F1h)
PIC18F44J50
On
0000h
SUM[000000:007FF7] + ([007FF8] & E1h) + ([007FF9] & 04h) + ([007FFA] & C7h) +
Off
PIC18F25J10
([007FFB] & 0Fh) + ([007FFD] & 01h)
PIC18F45J10
On
0000h
SUM[000000:007FF7] + ([007FF8] & E1h) + ([007FF9] & FCh) + ([007FFA] & DFh) +
Off
([007FFB] & FFh) + ([007FFC] & FFh) + ([007FFD] & F9h) + ([007FFE] & FFh) +
PIC18F25J11
([007FFF] & F1h)
PIC18F45J11
On
0000h
SUM[000000:007FF7] + ([007FF8] & EFh) + ([007FF9] & FFh) + ([007FFA] & DFh) +
Off
([007FFB] & FFh) + ([007FFC] & FFh) + ([007FFD] & F9h) + ([007FFE] & FFh) +
PIC18F25J50
([007FFF] & F1h)
PIC18F45J50
On
0000h
SUM[000000:00FFF7] + ([00FFF8] & E1h) + ([00FFF9] & FCh) + ([00FFFA] & DFh) +
Off
([00FFFB] & FFh) + ([00FFFC] & FFh) + ([00FFFD] & F9h) + ([00FFFE] & FFh) +
PIC18F26J11
([00FFFF] & F1h)
PIC18F46J11
On
0000h
SUM[000000:00FFF7] + ([00FFF8] & EFh) + ([00FFF9] & FFh) + ([00FFFA] & DFh) +
Off
([00FFFB] & FFh) + ([00FFFC] & FFh) + ([00FFFD] & F9h) + ([00FFFE] & FFh) +
PIC18F26J50
([00FFFF] & F1h)
PIC18F46J50
On
0000h
SUM[000000:00FFF7] + ([00FFF8] & FFh) + ([00FFF9] & FCh) +([00FFFA] & FFh) +
Off
([00FFFB] & FFh) + ([00FFFC] & FFh) + ([00FFFD] & FFh) + ([00FFFE] & BFh) +
PIC18F26J13
([00FFFF] & F3h)
PIC18F46J13
On
0000h
SUM[000000:00FFF7] + ([00FFF8] & FFh) + ([00FFF9] & FFh) +([00FFFA] & FFh) +
Off
([00FFFB] & FFh) + ([00FFFC] & FFh) + ([00FFFD] & FBh) + ([00FFFE] & BFh) +
PIC18F26J53
([00FFFF] & FBh)
PIC18F46J53
On
0000h
SUM[000000:01FFF7] + ([01FFF8] & FFh) + ([01FFF9] & FCh) + ([01FFFA] & FFh) +
Off
([01FFFB] & FFh) + ([01FFFC] & FFh) + ([01FFFD] & FFh) + ([01FFFE] & FFh) +
PIC18F27J13
([01FFFF] & F3h)
PIC18F47J13
On
0000h
SUM[000000:01FFF7] + ([01FFF8] & FFh) + ([01FFF9] & FFh) + ([01FFFA] & FFh) +
Off
([01FFFB] & FFh) + ([01FFFC] & FFh) + ([01FFFD] & FBh) + ([01FFFE] & FFh) +
PIC18F27J53
([01FFFF] & FBh)
PIC18F47J53
On
0000h
Legend: [a] = Value at address a; SUM[a:b] = Sum of locations a to b inclusive; + = Addition; & = Bitwise AND.
All addresses are hexadecimal.
DS30009687F-page 28
On
 2008-2015 Microchip Technology Inc.
PIC18F2XJXX/4XJXX FAMILY
6.0
AC/DC CHARACTERISTICS TIMING REQUIREMENTS
FOR PROGRAM/VERIFY TEST MODE
Standard Operating Conditions
Operating Temperature: 25C is recommended
Param
Symbol
No.
Characteristic
VDDCORE External Supply Voltage for Microcontroller
Core During Programming Operations
(PIC18LF devices)
D111
VDD
Supply Voltage During
Programming
Min.
Max.
Units
2.25
2.75
V
(Note 1)
Normal programming
(Note 2)
PIC18LFXXJXX VDDCORE
3.60
V
PIC18FXXJ10
2.70
3.60
V
PIC18FXXJ50
PIC18FXXJ11
PIC18FXXJ53
PIC18FXXJ13
2.35
3.60
V
Conditions
D112
IPP
Programming Current on MCLR
—
5
A
D113
IDDP
Supply Current During Programming
—
10
mA
D031
VIL
Input Low Voltage
VSS
0.2 VDD
V
D041
VIH
Input High Voltage
0.8 VDD
VDD
V
D080
VOL
Output Low Voltage
—
0.4
V
D090
VOH
Output High Voltage
2.4
—
V
IOH = -2.0 mA @ 3.3V
D012
CIO
Capacitive Loading on I/O pin (PGD)
—
50
pF
To meet AC specifications
CF
Filter Capacitor Value on
VCAP
PIC18LFXXJXX
0.1
—
F
(Note 1)
PIC18FXXJ10
4.7
18
F
PIC18FXXJ13
PIC18FXXJ11
PIC18FXXJ5X
5.4
18
F
Note 1:
2:
IOL = 3.4 mA @ 3.3V
External power must be supplied to the VDDCORE/VCAP pin if the on-chip voltage regulator is disabled. See
Section 2.1.1 “PIC18F2XJXX/4XJXX/ LF2XJXX/LF4XJXX Devices and the On-Chip Voltage Regulator” for
more information.
VDD must also be supplied to the AVDD pins during programming. AVDD and AVSS should always be within ±0.3V
of VDD and VSS, respectively.
 2008-2015 Microchip Technology Inc.
DS30009687F-page 29
PIC18F2XJXX/4XJXX FAMILY
6.0
AC/DC CHARACTERISTICS TIMING REQUIREMENTS
FOR PROGRAM/VERIFY TEST MODE (CONTINUED)
Standard Operating Conditions
Operating Temperature: 25C is recommended
Param
Symbol
No.
Characteristic
Min.
Max.
Units
—
1.0
s
Conditions
P1
TR
MCLR Rise Time to Enter Program/Verify
mode
P2
TPGC
Serial Clock (PGC) Period
100
—
ns
P2A
TPGCL
Serial Clock (PGC) Low Time
50
—
ns
P2B
TPGCH
Serial Clock (PGC) High Time
50
—
ns
P3
TSET1
Input Data Setup Time to Serial Clock 
20
—
ns
P4
THLD1
Input Data Hold Time from PGC
20
—
ns
P5
TDLY1
Delay Between 4-Bit Command and
Command Operand
50
—
ns
P5A
TDLY1A
Delay Between 4-Bit Command Operand and
Next 4-Bit Command
50
—
ns
P6
TDLY2
Delay Between Last PGC  of Command
Byte to First PGC  of Read of Data Word
20
—
ns
P9
TDLY5
Delay to allow Block Programming to occur
3.4
—
ms
PIC18F2XJ10/PIC18F4XJ10
1.2
—
ms
PIC18F2XJ11/PIC18F4XJ11/
PIC18F2XJ13/PIC18F4XJ13/
PIC18F2XJ5X/PIC18F4XJ5X
49
—
ms
PIC18F2XJ10/PIC18F4XJ10/
PIC18F2XJ13/PIC18F4XJ13/
PIC18F2XJ53/PIC18F4XJ53
54
—
ms
PIC18F2XJ11/PIC18F4XJ11/
PIC18F2XJ50/PIC18F4XJ50
475
—
ms
PIC18F2XJ10/PIC18F4XJ10/
PIC18F2XJ13/PIC18F4XJ13/
PIC18F2XJ53/PIC18F4XJ53
524
—
ms
PIC18F2XJ11/PIC18F4XJ11/
PIC18F2XJ50/PIC18F4XJ50
P10
P11
TDLY6
TDLY7
Delay to allow Row Erase to occur
Delay to allow Bulk Erase to occur
P12
THLD2
Input Data Hold Time from MCLR 
400
—
s
P13
TSET2
VDD Setup Time to MCLR 
100
—
ns
P14
TVALID
Data Out Valid from PGC 
25
—
ns
P16
TDLY8
Delay between Last PGC  and MCLR 
20
—
ns
P17
THLD3
MCLR to VDD 
3
—
s
P19
TKEY1
Delay from First MCLR to First PGC for
Key Sequence on PGD
4
—
ms
P20
TKEY2
Delay from Last PGC for Key Sequence on
PGD to Second MCLR 
50
—
ns
Note 1:
2:
External power must be supplied to the VDDCORE/VCAP pin if the on-chip voltage regulator is disabled. See
Section 2.1.1 “PIC18F2XJXX/4XJXX/ LF2XJXX/LF4XJXX Devices and the On-Chip Voltage Regulator” for
more information.
VDD must also be supplied to the AVDD pins during programming. AVDD and AVSS should always be within ±0.3V
of VDD and VSS, respectively.
DS30009687F-page 30
 2008-2015 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, flexPWR, JukeBlox, KEELOQ, KEELOQ logo, Kleer,
LANCheck, MediaLB, MOST, MOST logo, MPLAB,
OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC,
SST, SST Logo, SuperFlash and UNI/O are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
The Embedded Control Solutions Company and mTouch are
registered trademarks of Microchip Technology Incorporated
in the U.S.A.
Analog-for-the-Digital Age, BodyCom, chipKIT, chipKIT logo,
CodeGuard, dsPICDEM, dsPICDEM.net, ECAN, In-Circuit
Serial Programming, ICSP, Inter-Chip Connectivity, KleerNet,
KleerNet logo, MiWi, motorBench, MPASM, MPF, MPLAB
Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, RightTouch logo, REAL ICE, SQI, Serial Quad I/O,
Total Endurance, TSHARC, USBCheck, VariSense,
ViewSpan, WiperLock, Wireless DNA, and ZENA are
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip
Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2008-2015, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
ISBN: 978-1-63277-874-1
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
 2008-2015 Microchip Technology Inc.
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
DS30009687F-page 31
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Germany - Dusseldorf
Tel: 49-2129-3766400
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Hong Kong
Tel: 852-2943-5100
Fax: 852-2401-3431
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
Austin, TX
Tel: 512-257-3370
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Canada - Toronto
Tel: 905-673-0699
Fax: 905-673-6509
China - Dongguan
Tel: 86-769-8702-9880
China - Hangzhou
Tel: 86-571-8792-8115
Fax: 86-571-8792-8116
Germany - Karlsruhe
Tel: 49-721-625370
India - Pune
Tel: 91-20-3019-1500
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
Italy - Venice
Tel: 39-049-7625286
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-213-7828
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Poland - Warsaw
Tel: 48-22-3325737
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
07/14/15
DS30009687F-page 32
 2008-2015 Microchip Technology Inc.