MMA8452Q, 3-Axis, 12-bit/8-bit Digital Accelerometer - Data Sheet

Document Number: MMA8452Q
Rev. 10, 04/2016
NXP Semiconductors
Data sheet: Technical data
MMA8452Q, 3-axis, 12-bit/8-bit
digital accelerometer
MMA8452Q
The MMA8452Q is a smart, low-power, three-axis, capacitive, micromachined
accelerometer with 12 bits of resolution. This accelerometer is packed with
embedded functions with flexible user programmable options, configurable to two
interrupt pins. Embedded interrupt functions allow for overall power savings
relieving the host processor from continuously polling data.
Top and bottom view
The MMA8452Q has user selectable full scales of ±2 g/±4 g/±8 g with high-pass
filtered data as well as non-filtered data available real-time. The device can be
configured to generate inertial wakeup interrupt signals from any combination of
the configurable embedded functions allowing the MMA8452Q to monitor events
and remain in a low-power mode during periods of inactivity. The MMA8452Q is
available in a 16-pin QFN, 3 mm x 3 mm x 1 mm package.
Features
NC
NC
VDD
Top view
16
15
14
VDDIO
1
13
NC
BYP
2
12
GND
DNC
3
11
INT1
SCL
4
10
GND
GND
5
9
INT2
7
8
NC
6
SA0
•
•
•
•
•
16-pin QFN
3 mm x 3 mm x 1 mm
1.95 V to 3.6 V supply voltage
1.6 V to 3.6 V interface voltage
±2 g/±4 g/±8 g dynamically selectable full-scale
Output data rates (ODR) from 1.56 Hz to 800 Hz
99 μg/√Hz noise
12-bit and 8-bit digital output
I2C digital output interface
Two programmable interrupt pins for six interrupt sources
Three embedded channels of motion detection
— Freefall or motion detection: one channel
— Pulse detection: one channel
— Transient detection: one channel
Orientation (portrait/landscape) detection with set hysteresis
Automatic ODR change for auto-wake and return to sleep
High-pass filter data available real-time
Self-test
Current consumption: 6 μA to 165 μA
SDA
•
•
•
•
•
•
•
•
•
Typical applications
Pin connections
•
E-compass applications
•
Static orientation detection (portrait/landscape, up/down, left/right, back/front
position identification)
•
Notebook, e-reader, and laptop tumble and freefall detection
•
Real-time orientation detection (virtual reality and gaming 3D user position feedback)
•
Real-time activity analysis (pedometer step counting, freefall drop detection for HDD, dead-reckoning GPS backup)
•
Motion detection for portable product power saving (auto-sleep and auto-wake for cell phone, PDA, GPS, gaming)
•
Shock and vibration monitoring (mechatronic compensation, shipping and warranty usage logging)
•
User interface (menu scrolling by orientation change, pulse detection for button replacement)
Ordering information
Part number
Temperature range
Package description
MMA8452QT
–40°C to +85°C
QFN-16
Tray
MMA8452QR1
–40°C to +85°C
QFN-16
Tape and Reel
© 2016 NXP B.V.
Shipping
Contents
1
2
3
4
5
6
7
8
9
Block Diagram and Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Mechanical and Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Mechanical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 I2C interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2 Zero-g offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.3 Self-test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
System Modes (SYSMOD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1 Device calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2 8-bit or 12-bit data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3 Low-power modes vs. high-resolution modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.4 Auto-wake/sleep mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.5 Freefall and motion detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.6 Transient detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.7 Pulse detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.8 Orientation detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.9 Interrupt register configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.10 Serial I2C interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Register Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.1 Data registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.2 Portrait/landscape embedded function registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.3 Motion and freefall embedded function registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.4 Transient (HPF) acceleration detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.5 Single, double and directional pulse-detection registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.6 Auto-wake/sleep detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
6.7 Control registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
6.8 User offset correction registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Printed Circuit Board Layout and Device Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
7.1 Printed circuit board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
7.2 Overview of soldering considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
7.3 Halogen content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Package Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
8.1 Tape and reel information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
8.2 Package description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Related documentation
The MMA8452Q device features and operations are described in a variety of reference manuals, user guides, and application
notes. To find the most-current versions of these documents:
1.
Go to the NXP homepage at:
http://www.nxp.com/
2.
3.
In the ALL search box at the top of the page, enter the device number MMA8452Q.
Click the Documents link.
MMA8452Q
2
Sensors
NXP Semiconductors
1
Block Diagram and Pin Description
Internal
OSC
X-axis
Transducer
VDD
VDDIO
INT2
Embedded
DSP
Functions
12-bit
ADC
C to V
Converter
Y-axis
Transducer
VSS
INT1
Clock
GEN
I2 C
SDA
SCL
Z-axis
Transducer
Transient
Detection
(i.e., fast-motion,
transient)
Freefall
and Motion
Detection
Orientation with
Set Hysteresis
and Z-lockout
Shake Detection
through
Motion
Threshold
Single, Double
and Directional
Tap Detection
Auto-wake/auto-sleep configurable with debounce counter and multiple motion interrupts for control
MODE Options
Low Power
Low Noise + Low Power
High Resolution
Normal
Active mode
Active mode
wake
sleep
Auto-wake/sleep
MODE Options
Low Power
Low Noise + Low Power
High Resolution
Normal
Figure 1. Block diagram
Z
Earth Gravity
X
1
Y
(TOP VIEW)
DIRECTION OF THE
DETECTABLE ACCELERATIONS
13
1
9
5
(BOTTOM VIEW)
Figure 2. Direction of the detectable accelerations
MMA8452Q
Sensors
NXP Semiconductors
3
Figure 3 shows the device configuration in the six different orientation modes. These orientations are defined as the following:
PU = portrait up, LR = landscape right, PD = portrait down, LL = landscape left, back and front side views. There are several
registers to configure the orientation detection and are described in detail in the register setting section.
Top View
PU
Pin 1
Earth Gravity
Side View
LL
LR
Xout @ 0 g
Yout @ –1 g
Zout @ 0 g
BACK
Xout @ 0 g
Yout @ 0 g
Zout @ –1 g
PD
Xout @ –1 g
Yout @ 0 g
Zout @ 0 g
Xout @ 1 g
Yout @ 0 g
Zout @ 0 g
FRONT
Xout @ 0 g
Yout @ 0 g
Zout @ 1 g
Xout @ 0 g
Yout @ 1 g
Zout @ 0 g
Figure 3. Landscape/portrait orientation
1.6V - 3.6V
VDDIO
1.95V - 3.6V
VDD
4.7μF
0.1μF
DNC
NC
4
SCL
5
GND
VDD
3
NC
BYP
MMA8452Q
NC
4.7kΩ
0.1μF
2
14
SA0
4.7kΩ
VDDIO
VDDIO
15
SDA
VDDIO
1
NC
16
6
7
8
NC
13
GND
12
INT1
11
GND
10
INT2
9
INT1
SCL
INT2
SA0
SDA
Figure 4. Application diagram
MMA8452Q
4
Sensors
NXP Semiconductors
Table 1. Pin descriptions
Pin #
Pin name
Description
1
VDDIO
2
BYP
Bypass capacitor (0.1 μF)
3
DNC
Do not connect to anything, leave pin isolated and floating.
4
SCL
I2C serial clock, open drain
5
GND
Connect to ground
6
SDA
I2C serial data
7
SA0
I2C least significant bit of the device I2C address, I2C 7-bit address = 0x1C (SA0 = 0), 0x1D (SA0 = 1).
8
NC
Internally not connected
9
INT2
Inertial interrupt 2, output pin
10
GND
Connect to ground
11
INT1
Inertial interrupt 1, output pin
12
GND
Connect to ground
13
NC
14
VDD
15
NC
Internally not connected
16
NC
Internally not connected (can be GND or VDD)
Internal power supply (1.62 V to 3.6 V)
Internally not connected
Power supply (1.95 V to 3.6 V)
The device power is supplied through VDD line. Power supply decoupling capacitors (100 nF ceramic plus 4.7 µF bulk, or a single
4.7 µF ceramic) should be placed as near as possible to the pins 1 and 14 of the device.
The control signals SCL, SDA, and SA0 are not tolerant of voltages more than VDDIO + 0.3 V. If VDDIO is removed, the control
signals SCL, SDA, and SA0 will clamp any logic signals with their internal ESD protection diodes.
The functions, the threshold and the timing of the two interrupt pins (INT1 and INT2) are user programmable through the I2C
interface. The SDA and SCL I2C connections are open drain and therefore require a pullup resistor as shown in the application
diagram in Figure 4.
MMA8452Q
Sensors
NXP Semiconductors
5
2
Mechanical and Electrical Specifications
2.1
Mechanical characteristics
Table 2. Mechanical characteristics @ VDD = 2.5 V, VDDIO = 1.8 V, T = 25 °C unless otherwise noted.
Parameter
Test conditions
Symbol
Min
Typ
Max
—
±2
—
—
±4
—
FS[1:0] set to 10
8 g mode
—
±8
—
FS[1:0] set to 00
2 g mode
—
1024
—
—
512
—
—
256
—
—
±2.64
—
FS[1:0] set to 00
2 g mode
Measurement range(1)
Sensitivity
FS[1:0] set to 01
4 g mode
FS[1:0] set to 01
4 g mode
FS
So
FS[1:0] set to 10
8 g mode
Sensitivity accuracy(2)
—
Soa
FS[1:0] set to 00
2 g mode
Sensitivity change vs. temperature
FS[1:0] set to 01
4 g mode
—
TCSo
FS[1:0] set to 10
8 g mode
—
Unit
g
counts/g
%
—
±0.008
—
—
%/°C
—
Zero-g level offset accuracy(3)
FS[1:0] 2 g, 4 g, 8 g
TyOff
—
±17
—
mg
Zero-g level offset accuracy post-board mount(4)
FS[1:0] 2 g, 4 g, 8 g
TyOffPBM
—
±20
—
mg
Zero-g level change vs. temperature
–40 °C to 85 °C
TCOff
—
±0.15
—
mg/°C
Self-test output change(5)
X
Y
Z
FS[1:0] set to 0
4 g mode
Vst
—
—
—
+44
+61
+392
—
—
—
ODR accuracy
2-MHz clock
—
—
—
±2
—
Output data bandwidth
—
BW
ODR/3
—
ODR/2
Hz
Output noise
Normal mode ODR = 400 Hz
Noise
—
126
—
µg/√Hz
Output noise low-noise mode(1)
Normal mode ODR = 400 Hz
Noise
—
99
—
µg/√Hz
—
Top
–40
—
+85
°C
Operating temperature range
LSB
%
1. Dynamic range is limited to 4 g when the low-noise bit in register 0x2A, bit 2 is set.
2. Sensitivity remains in spec as stated, but changing oversampling mode to low power causes 3% sensitivity shift. This behavior is also seen
when changing from 800 Hz to any other data rate in the normal, low noise + low power or high resolution mode.
3. Before board mount.
4. Post-board mount offset specifications are based on an 8-layer PCB, relative to 25°C.
5. Self-test is one direction only.
MMA8452Q
6
Sensors
NXP Semiconductors
2.2
Electrical characteristics
Table 3. Electrical characteristics @ VDD = 2.5 V, VDDIO = 1.8 V, T = 25 °C unless otherwise noted.
Parameter
Supply voltage
Interface supply voltage
Test conditions
Symbol
Min
Typ
Max
Unit
—
VDD(1)
1.95
2.5
3.6
V
—
VDDIO(1)
1.62
1.8
3.6
V
ODR = 1.56 Hz
—
6
—
ODR = 6.25 Hz
—
6
—
ODR = 12.5 Hz
—
6
—
—
14
—
—
24
—
ODR = 200 Hz
—
44
—
ODR = 400 Hz
—
85
—
ODR = 800 Hz
—
165
—
ODR = 1.56 Hz
—
24
—
ODR = 6.25 Hz
—
24
—
ODR = 12.5 Hz
—
24
—
—
24
—
—
44
—
ODR = 50 Hz
Low-power mode
ODR = 100 Hz
IddLP
ODR = 50 Hz
Normal mode
ODR = 100 Hz
Idd
ODR = 200 Hz
—
85
—
ODR = 400 Hz
—
165
—
ODR = 800 Hz
—
165
—
μA
μA
Current during boot sequence, 0.5 mSec max
duration using recommended bypass cap
VDD = 2.5 V
Idd Boot
—
—
1
mA
Value of capacitor on BYP pin
–40 °C 85 °C
Cap
75
100
470
nF
VDD = 2.5 V, VDDIO = 1.8 V,
standby mode
IddStby
—
1.8
5
μA
VIH
0.7*VDDIO
—
—
VIL
—
—
0.3*VDDIO
Standby mode current @ 25 °C
Digital high-level input voltage
SCL, SDA, SA0
—
Digital low-level input voltage
SCL, SDA, SA0
—
V
High-level output voltage
INT1, INT2
IO = 500 μA
VOH
0.9*VDDIO
—
—
Low-level output voltage
INT1, INT2
IO = 500 μA
VOL
—
—
0.1*VDDIO
Low-level output voltage
SDA
IO = 500 μA
VOLS
—
Power on ramp time
Boot time
Turn-on time(2)
Turn-on time
Operating temperature range
—
—
V
V
0.1*VDDIO
V
V
0.001
—
1000
ms
350
500
µs
Time from VDDIO on and
VDD > VDD min until I2C is ready
for operation, Cbyp = 100 nF
Tbt
—
Time to obtain valid data from
standby mode to active mode.
Ton1
—
2/ODR + 1 ms
s
Time to obtain valid data from valid
voltage applied.
Ton2
—
2/ODR + 2 ms
—
—
Top
–40
—
+85
°C
1. There is no requirement for power supply sequencing. The VDDIO input voltage can be higher than the VDD input voltage.
2. Note the first sample is typically not very precise. Depending on ODR/MODS setting, a minimum of three samples is recommended for full
precision.
MMA8452Q
Sensors
NXP Semiconductors
7
2.3
I2C interface characteristics
Table 4. I2C slave timing values(1)
I2C fast-mode
Parameter
Unit
Symbol
Min
Max
SCL clock frequency
fSCL
0
400
kHz
Bus-free time between stop and start condition
tBUF
1.3
—
μs
(Repeated) start hold time
tHD;STA
0.6
—
μs
Repeated start setup time
tSU;STA
0.6
—
μs
Stop condition setup time
tSU;STO
0.6
—
μs
μs
SDA data hold time
tHD;DAT
0.05
0.9(2)
SDA setup time
tSU;DAT
100
—
ns
SCL clock low time
tLOW
1.3
—
μs
SCL clock high time
tHIGH
0.6
SDA and SCL rise time
SDA and SCL fall time
tr
tf
—
μs
20 + 0.1 Cb
(3)
300
ns
20 + 0.1 Cb
(3)
300
ns
SDA valid time (4)
tVD;DAT
—
0.9(2)
μs
SDA valid acknowledge time (5)
tVD;ACK
—
0.9(2)
μs
Pulse width of spikes on SDA and SCL that must be suppressed by
internal input filter
tSP
0
50
ns
Capacitive load for each bus line
Cb
—
400
pF
1.All values referred to VIH(min) (0.3 VDD) and VIL(max) (0.7 VDD) levels.
2.This device does not stretch the low period (tLOW) of the SCL signal.
3.Cb = total capacitance of one bus line in pF.
4.tVD;DAT = time for data signal from SCL low to SDA output (high or low, depending on which one is worse).
5.tVD;ACK = time for acknowledgement signal from SCL low to SDA output (high or low, depending on which one is worse).
MMA8452Q
8
Sensors
NXP Semiconductors
VIL = 0.3VDD
VIH = 0.7VDD
Figure 5. I2C slave timing diagram
2.4
Absolute maximum ratings
Stresses above those listed as absolute maximum ratings may cause permanent damage to the device. Exposure to maximum
rating conditions for extended periods may affect device reliability.
Table 5. Maximum ratings
Rating
Symbol
Value
Unit
Maximum acceleration (all axes, 100 μs)
gmax
5,000
g
Supply voltage
VDD
–0.3 to + 3.6
V
Vin
–0.3 to VDDIO + 0.3
V
Drop test
Ddrop
1.8
m
Operating temperature range
TOP
–40 to +85
°C
Storage temperature range
TSTG
–40 to +125
°C
Symbol
Value
Unit
Human body model
HBM
±2000
V
Machine model
MM
±200
V
CDM
±500
V
—
±100
mA
Input voltage on any control pin (SA0, SCL, SDA)
Table 6. ESD and latchup protection characteristics
Rating
Charge device model
Latchup current at T = 85°C
This device is sensitive to mechanical shock. Improper handling can cause permanent damage of the part or
cause the part to otherwise fail.
This device is sensitive to ESD, improper handling can cause permanent damage to the part.
MMA8452Q
Sensors
NXP Semiconductors
9
3
Terminology
3.1
Sensitivity
The sensitivity is represented in counts/g. In 2 g mode the sensitivity is 1024 counts/g. In 4 g mode the sensitivity is
512 counts/g and in 8 g mode the sensitivity is 256 counts/g.
3.2
Zero-g offset
Zero-g offset (TyOff) describes the deviation of an actual output signal from the ideal output signal if the sensor is stationary. A
sensor stationary on a horizontal surface will measure 0 g in X-axis and 0 g in Y-axis whereas the Z-axis will measure 1 g. The
output is ideally in the middle of the dynamic range of the sensor (content of OUT registers 0x00, data expressed as 2's
complement number). A deviation from ideal value in this case is called zero-g offset. Offset is to some extent a result of stress
on the MEMS sensor and therefore the offset can slightly change after mounting the sensor onto a printed circuit board or
exposing it to extensive mechanical stress.
3.3
Self-test
Self-test checks the transducer functionality without external mechanical stimulus. When self-test is activated, an electrostatic
actuation force is applied to the sensor, simulating a small acceleration. In this case, the sensor outputs will exhibit a change in
their DC levels which are related to the selected full scale through the device sensitivity. When self-test is activated, the device
output level is given by the algebraic sum of the signals produced by the acceleration acting on the sensor and by the electrostatic
test-force.
MMA8452Q
10
Sensors
NXP Semiconductors
4
System Modes (SYSMOD)
OFF
SYSMOD = 10
CTRL_REG1
Active bit = 0
VDD > 1.8 V
Standby
SYSMOD = 00
OFF
VDD < 1.8 V
Active
Auto-sleep/wake
Condition
CTRL_REG1
Active bit = 1
CTRL_REG1
Active bit = 0
Wake
SYSMOD = 01
Figure 6. MMA8452Q mode transition diagram
Table 7. Mode of operation description
I2C bus state
Mode
OFF
Powered down
VDD
< 1.8 V
VDDIO Can be > VDD
Function description
• The device is powered off.
• All analog and digital blocks are shutdown.
• I2C bus inhibited.
Standby
I2C communication is possible
> 1.8 V
• Only digital blocks are enabled.
analog subsystem is disabled.
• Internal clocks disabled.
• Registers accessible for read/write.
• Device is configured in standby mode.
Active
(wake/sleep)
I2C communication is possible
> 1.8 V
• All blocks are enabled (digital, analog).
All register contents are preserved when transitioning from active to standby mode. Some registers are reset when transitioning
from standby to active. These are all noted in the device memory map register table. The sleep and wake modes are active
modes. For more information on how to use the sleep and wake modes and how to transition between these modes, please refer
to the functionality section of this document.
MMA8452Q
Sensors
NXP Semiconductors
11
5
Functionality
The MMA8452Q is a low-power, digital output 3-axis linear accelerometer with a I2C interface and embedded logic used to detect
events and notify an external microprocessor over interrupt lines. The functionality includes the following:
• 8-bit or 12-bit data which includes high-pass filtered data
• Four different oversampling options for compromising between resolution and current consumption based on application
requirements
• Additional low-noise mode that functions independently of the oversampling modes for higher resolution
• Low-power and auto-wake/sleep modes for conservation of current consumption
• Single-/double-pulse with directional information one channel
• Motion detection with directional information or freefall one channel
• Transient detection based on a high-pass filter and settable threshold for detecting the change in acceleration above a
threshold with directional information one channel
• Portrait/landscape detection with trip points fixed at 30° and 60° for smooth transitions between orientations.
All functionality is available in 2 g, 4 g or 8 g dynamic ranges. There are many configuration settings for enabling all the different
functions. Separate application notes have been provided to help configure the device for each embedded functionality.
Table 8. Features of the MMA845xQ devices
Feature list
MMA8451Q
MMA8452Q
MMA8453Q
14
12
10
Digital sensitivity (counts/g)
4096
1024
256
Data-ready interrupt
Yes
Yes
Yes
Single-pulse interrupt
Yes
Yes
Yes
Double-pulse interrupt
Yes
Yes
Yes
Directional-pulse interrupt
Yes
Yes
Yes
Auto-wake
Yes
Yes
Yes
Auto-sleep
Yes
Yes
Yes
Freefall interrupt
Yes
Yes
Yes
32-level FIFO
Yes
No
No
High-pass filter
Yes
Yes
Yes
Low-pass filter
Yes
Yes
Yes
Orientation detection portrait/landscape = 30°, landscape to portrait = 60°,
and fixed 45° threshold
Yes
Yes
Yes
Programmable orientation detection
Yes
No
No
Motion interrupt with direction
Yes
Yes
Yes
Transient detection with high-pass filter
Yes
Yes
Yes
Low-power mode
Yes
Yes
Yes
Digital resolution (bits)
MMA8452Q
12
Sensors
NXP Semiconductors
5.1
Device calibration
The device interface is factory calibrated for sensitivity and zero-g offset for each axis. The trim values are stored in non-volatile
memory (NVM). On power-up, the trim parameters are read from NVM and applied to the circuitry. In normal use, further
calibration in the end application is not necessary. However, the MMA8452Q allows the user to adjust the zero-g offset for each
axis after power-up, changing the default offset values. The user offset adjustments are stored in six volatile registers. For more
information on device calibration, refer to application note, AN4069.
5.2
8-bit or 12-bit data
The measured acceleration data is stored in the OUT_X_MSB, OUT_X_LSB, OUT_Y_MSB, OUT_Y_LSB, OUT_Z_MSB, and
OUT_Z_LSB registers as 2’s complement 12-bit numbers. The most significant 8-bits of each axis are stored in OUT_X (Y,
Z)_MSB, so applications needing only 8-bit results can use these three registers and ignore OUT_X,Y, Z_LSB. To do this, the
F_READ bit in CTRL_REG1 must be set. When the F_READ bit is cleared, the fast-read mode is disabled.
When the full-scale is set to 2 g, the measurement range is –2 g to +1.999 g, and each count corresponds to 1 g/1024
(1 mg) at 12-bits resolution. When the full-scale is set to 8 g, the measurement range is –8 g to +7.996 g, and each count
corresponds to 1 g/256 (3.9 mg) at 12-bits resolution. The resolution is reduced by a factor of 16 if only the 8-bit results are used.
For more information on the data manipulation between data formats and modes, refer to NXP application note AN4076. There
is a device driver available that can be used with the Sensor Toolbox demo board (LFSTBEB8451, 2, 3Q).
5.3
Low-power modes vs. high-resolution modes
The MMA8452Q can be optimized for lower power modes or for higher resolution of the output data. High resolution is achieved
by setting the LNOISE bit in register 0x2A. This improves the resolution but be aware that the dynamic range is limited to 4 g
when this bit is set. This will affect all internal functions and reduce noise. Another method for improving the resolution of the data
is by oversampling. One of the oversampling schemes of the data can activated when MODS = 10 in register 0x2B which will
improve the resolution of the output data only. The highest resolution is achieved at 1.56 Hz.
There is a trade-off between low power and high resolution. Low power can be achieved when the oversampling rate is reduced.
The lowest power is achieved when MODS = 11 or when the sample rate is set to 1.56 Hz. For more information on how to
configure the MMA8452Q in low-power mode or high-resolution mode and to realize the benefits, refer to NXP application note
AN4075.
5.4
Auto-wake/sleep mode
The MMA8452Q can be configured to transition between sample rates (with their respective current consumption) based on four
of the interrupt functions of the device. The advantage of using the auto-wake/sleep is that the system can automatically transition
to a higher sample rate (higher current consumption) when needed but spends the majority of the time in the sleep mode (lower
current) when the device does not require higher sampling rates. Auto-wake refers to the device being triggered by one of the
interrupt functions to transition to a higher sample rate. This may also interrupt the processor to transition from a sleep mode to a
higher power mode.
Sleep mode occurs after the accelerometer has not detected an interrupt for longer than the user definable time-out period. The
device will transition to the specified lower sample rate. It may also alert the processor to go into a lower power mode to save on
current during this period of inactivity.
The interrupts that can wake the device from sleep are the following: pulse detection, orientation detection, motion/freefall, and
transient detection. Refer to AN4074, for more detailed information for configuring the auto-wake/sleep.
5.5
Freefall and motion detection
MMA8452Q has flexible interrupt architecture for detecting either a freefall or a motion. Freefall can be enabled where the set
threshold must be less than the configured threshold, or motion can be enabled where the set threshold must be greater than
the threshold. The motion configuration has the option of enabling or disabling a high-pass filter to eliminate tilt data (static offset).
The freefall does not use the high-pass filter. For details on the freefall and motion detection with specific application examples
and recommended configuration settings, refer to NXP application note AN4070.
5.5.1
Freefall detection
The detection of freefall involves the monitoring of the X, Y, and Z axes for the condition where the acceleration magnitude is
below a user specified threshold for a user definable amount of time. Normally, the usable threshold ranges are between
±100 mg and ±500 mg.
MMA8452Q
Sensors
NXP Semiconductors
13
5.5.2
Motion detection
Motion is often used to simply alert the main processor that the device is currently in use. When the acceleration exceeds a set
threshold the motion interrupt is asserted. A motion can be a fast moving shake or a slow moving tilt. This will depend on the
threshold and timing values configured for the event. The motion detection function can analyze static acceleration changes or
faster jolts. For example, to detect that an object is spinning, all three axes would be enabled with a threshold detection of > 2 g.
This condition would need to occur for a minimum of 100 ms to ensure that the event wasn't just noise. The timing value is set
by a configurable debounce counter. The debounce counter acts like a filter to determine whether the condition exists for
configurable set of time (i.e., 100 ms or longer). There is also directional data available in the source register to detect the
direction of the motion. This is useful for applications such as directional shake or flick, which assists with the algorithm for various
gesture detections.
5.6
Transient detection
The MMA8452Q has a built-in high-pass filter. Acceleration data goes through the high-pass filter, eliminating the offset (DC) and
low frequencies. The high-pass filter cutoff frequency can be set by the user to four different frequencies which are dependent
on the output data rate (ODR). A higher cutoff frequency ensures the DC data or slower moving data will be filtered out, allowing
only the higher frequencies to pass. The embedded transient detection function uses the high-pass filtered data allowing the user
to set the threshold and debounce counter. The transient detection feature can be used in the same manner as the motion
detection by bypassing the high-pass filter. There is an option in the configuration register to do this. This adds more flexibility to
cover various customer use cases.
Many applications use the accelerometer’s static acceleration readings (i.e., tilt) which measure the change in acceleration due
to gravity only. These functions benefit from acceleration data being filtered with a low-pass filter where high-frequency data is
considered noise. However, there are many functions where the accelerometer must analyze dynamic acceleration. Functions
such as tap, flick, shake and step counting are based on the analysis of the change in the acceleration. It is simpler to interpret
these functions dependent on dynamic acceleration data when the static component has been removed. The transient detection
function can be routed to either interrupt pin through bit 5 in CTRL_REG5 register (0x2E). registers 0x1D to 0x20 are the
dedicated transient detection configuration registers. The source register contains directional data to determine the direction of the
acceleration, either positive or negative. For details on the benefits of the embedded transient detection function along with specific
application examples and recommended configuration settings, please refer to NXP application note AN4071.
5.7
Pulse detection
The MMA8452Q has embedded single/double and directional pulse detection. This function has various customizing timers for
setting the pulse time width and the latency time between pulses. There are programmable thresholds for all three axes. The
pulse detection can be configured to run through the high-pass filter and also through a low-pass filter, which provides more
customizing and tunable pulse-detection schemes. The status register provides updates on the axes where the event was
detected and the direction of the tap. For more information on how to configure the device for pulse detection, please refer to
NXP application note AN4072.
5.8
Orientation detection
The MMA8452Q has an orientation detection algorithm with the ability to detect all six orientations. The transition from portrait to
landscape is fixed with a 45° threshold angle and a ±14° hysteresis angle. This allows the for a smooth transition from portrait to
landscape at approximately 30° and then from landscape to portrait at approximately 60°.
The angle at which the device no longer detects the orientation change is referred to as the Z-lockout angle. The device operates
down to 29° from the flat position. All angles are accurate to ±2°.
For further information on the orientation detection function refer to NXP application note AN4068.
Figure 8 shows the definitions of the trip angles going from landscape to portrait (A) and then also from portrait to landscape (B).
MMA8452Q
14
Sensors
NXP Semiconductors
Top View
PU
Pin 1
Side View
Earth Gravity
BACK
LL
LR
Xout @ 0 g
Yout @ –1 g
Zout @ 0 g
Xout @ 0 g
Yout @ 0 g
Zout @ –1 g
FRONT
PD
Xout @ –1 g
Yout @ 0 g
Zout @ 0 g
Xout @ 1 g
Yout @ 0 g
Zout @ 0 g
Xout @ 0 g
Yout @ 0 g
Zout @ 1 g
Xout @ 0 g
Yout @ 1 g
Zout @ 0 g
Figure 7. Landscape/portrait orientation
Portrait
90°
Portrait
90°
Landscape to portrait
Trip angle = 60°
Portrait to landscape
Trip angle = 30°
0° Landscape
0° Landscape
(A)
(B)
Figure 8. Illustration of landscape to portrait transition (A) and portrait to landscape transition (B)
Figure 9 illustrates the Z-angle lockout region. When lifting the device upright from the flat position it will be active for orientation
detection as low as 29° from flat.
Upright
90°
NORMAL
DETECTION
REGION
Z-LOCK = 29°
LOCKOUT
REGION
0° Flat
Figure 9. Illustration of Z-tilt angle lockout transition
MMA8452Q
Sensors
NXP Semiconductors
15
5.9
Interrupt register configurations
There are six configurable interrupts in the MMA8452Q: data-ready, motion/freefall, pulse, orientation, transient, and auto-sleep
events. These six interrupt sources can be routed to one of two interrupt pins. The interrupt source must be enabled and
configured. If the event flag is asserted because the event condition is detected, the corresponding interrupt pin, INT1 or INT2,
will assert.
Data Ready
INT1
Motion/Freefall
Pulse
INTERRUPT
CONTROLLER
Orientation
INT2
Transient
Auto-sleep
6
INT ENABLE
6
INT CFG
Figure 10. System interrupt generation block diagram
5.10
Serial I2C interface
Acceleration data may be accessed through an I2C interface thus making the device particularly suitable for direct interfacing with
a microcontroller. The MMA8452Q features an interrupt signal which indicates when a new set of measured acceleration data is
available thus simplifying data synchronization in the digital system that uses the device. The MMA8452Q may also be configured
to generate other interrupt signals accordingly to the programmable embedded functions of the device for motion, freefall,
transient, orientation, and pulse.
The registers embedded inside the MMA8452Q are accessed through the I2C serial interface (Table 9). To enable the I2C
interface, VDDIO line must be tied high (i.e., to the interface supply voltage). If VDD is not present and VDDIO is present, the
MMA8452Q is in off mode and communications on the I2C interface are ignored. The I2C interface may be used for
communications between other I2C devices and the MMA8452Q does not affect the I2C bus.
Table 9. Serial interface pin description
Pin name
Pin description
SCL
I2C serial clock
SDA
I2C serial data
SA0
I2C least significant bit of the device address
There are two signals associated with the I2C bus; the serial clock line (SCL) and the serial data line (SDA). The latter is a
bidirectional line used for sending and receiving the data to/from the interface. External pullup resistors connected to VDDIO are
expected for SDA and SCL. When the bus is free both the lines are high. The I2C interface is compliant with fast mode (400 kHz),
and normal mode (100 kHz) I2C standards (Table 5).
MMA8452Q
16
Sensors
NXP Semiconductors
5.10.1
I2C operation
The transaction on the bus is started through a start condition (start) signal. Start condition is defined as a high to low transition on
the data line while the SCL line is held high. After start has been transmitted by the master, the bus is considered busy. The next
byte of data transmitted after start contains the slave address in the first seven bits, and the eighth bit tells whether the master is
receiving data from the slave or transmitting data to the slave. When an address is sent, each device in the system compares the
first seven bits after a start condition with its address. If they match, the device considers itself addressed by the master. The 9th
clock pulse, following the slave address byte (and each subsequent byte) is the acknowledge (ACK). The transmitter must
release the SDA line during the ACK period. The receiver must then pull the data line low so that it remains stable low during the
high period of the acknowledge clock period.
A low to high transition on the SDA line while the SCL line is high is defined as a stop condition (stop). A data transfer is always
terminated by a stop. A master may also issue a repeated start during a data transfer. The MMA8452Q expects repeated starts
to be used to randomly read from specific registers.
The MMA8452Q's standard slave address is a choice between the two sequential addresses 0011100 and 0011101. The selection
is made by the high- and low-logic level of the SA0 (pin 7) input respectively. The slave addresses are factory programmed and
alternate addresses are available at customer request. The format is shown in Table 10.
Single-byte read
The MMA8452Q has an internal ADC that can sample, convert and return sensor data on request. The transmission of an
8-bit command begins on the falling edge of SCL. After the eight clock cycles are used to send the command, note that the data
returned is sent with the MSB first once the data is received. Figure 11 shows the timing diagram for the accelerometer 8-bit I2C
read operation. The master (or MCU) transmits a start condition (ST) to the MMA8452Q, slave address ($1D), with the R/W bit
set to ‘0’ for a write, and the MMA8452Q sends an acknowledgement. Then the master (or MCU) transmits the address of the
register to read and the MMA8452Q sends an acknowledgement. The master (or MCU) transmits a repeated start condition (SR)
and then addresses the MMA8452Q ($1D) with the R/W bit set to ‘1’ for a read from the previously selected register. The Slave
then acknowledges and transmits the data from the requested register. The master does not acknowledge (NAK) the transmitted
data, but transmits a stop condition to end the data transfer.
Multiple-byte read
When performing a multi-byte read or burst read, the MMA8452Q automatically increments the received register address
commands after a read command is received. Therefore, after following the steps of a single-byte read, multiple bytes of data
can be read from sequential registers after each MMA8452Q acknowledgment (AK) is received until a no acknowledge (NAK)
occurs from the master followed by a stop condition (SP) signaling an end of transmission.
Single-byte write
To start a write command, the master transmits a start condition (ST) to the MMA8452Q, slave address ($1D) with the R/W bit set
to ‘0’ for a write, the MMA8452Q sends an acknowledgement. Then the master (MCU) transmits the address of the register to
write to, and the MMA8452Q sends an acknowledgement. Then the master (or MCU) transmits the 8-bit data to write to the
designated register and the MMA8452Q sends an acknowledgement that it has received the data. Since this transmission is
complete, the master transmits a stop condition (SP) to the data transfer. The data sent to the MMA8452Q is now stored in the
appropriate register.
Multiple-byte write
The MMA8452Q automatically increments the received register address commands after a write command is received.
Therefore, after following the steps of a single-byte write, multiple bytes of data can be written to sequential registers after each
MMA8452Q acknowledgment (ACK) is received.
Table 10. I2C device address sequence
Command
[7:2]
Device address
[1]
SA0
[7:1]
Device address
R/W
[7:0]
8-bit final value
Read
001110
0
0x1C
1
0x39
Write
001110
0
0x1C
0
0x38
Read
001110
1
0x1D
1
0x3B
Write
001110
1
0x1D
0
0x3A
MMA8452Q
Sensors
NXP Semiconductors
17
I2C data sequence diagrams
< Single-byte read >
Master
ST
Device Address[6:0]
W
Register Address[7:0]
AK
Slave
SR
Device Address[6:0]
R
AK
NAK SP
AK
Data[7:0]
< Multiple-byte read >
Master
ST
Device Address[6:0]
W
Register Address[7:0]
AK
Slave
AK
Master
Data[7:0]
R
AK
AK
Data[7:0]
Slave
SR Device Address[6:0]
AK
AK
NAK
Data[7:0]
SP
Data[7:0]
< Single-byte write >
ST
Master
Device Address[6:0]
W
Register Address[7:0]
AK
Slave
Data[7:0]
AK
SP
AK
< Multiple-byte write >
Master
ST
Device Address[6:0]
Slave
W
Register Address[7:0]
AK
Data[7:0]
AK
Data[7:0]
AK
SP
AK
Legend
ST: Start condition
SP: Stop condition
NAK: No acknowledge
SR: Repeated start condition
AK: Acknowledge
R: Read = 1
W: Write = 0
Figure 11. I2C data sequence diagrams
MMA8452Q
18
Sensors
NXP Semiconductors
6
Register Descriptions
Table 11. Register address map
Name
Type
Register
address
Auto-increment address
F_READ = 0
Default
Hex
value
00000000
0x00
F_READ = 1
Comment
STATUS(1)(2)
R
0x00
OUT_X_MSB(1)(2)
R
0x01
0x02
0x03
Output
—
[7:0] are 8 MSBs of 12-bit sample.
OUT_X_LSB(1)(2)
R
0x02
0x03
0x00
Output
—
[7:4] are 4 LSBs of 12-bit sample.
OUT_Y_MSB(1)(2)
R
0x03
0x04
0x05
Output
—
[7:0] are 8 MSBs of 12-bit sample.
OUT_Y_LSB(1)(2)
R
0x04
0x05
0x00
Output
—
[7:4] are 4 LSBs of 12-bit sample.
OUT_Z_MSB(1)(2)
R
0x05
0x06
0x00
Output
—
[7:0] are 8 MSBs of 12-bit sample.
OUT_Z_LSB(1)(2)
R
0x06
0x00
Output
—
[7:4] are 4 LSBs of 12-bit sample.
Reserved
R
0x07
—
—
—
Reserved. Read return 0x00.
Reserved
R
0x08
—
—
—
Reserved. Read return 0x00.
SYSMOD
R
0x0B
0x0C
00000000
0x00
Current System mode
INT_SOURCE(1)(2)
R
0x0C
0x0D
00000000
0x00
Interrupt status
WHO_AM_I
R
0x0D
0x0E
00101010
0x2A
Device ID (0x2A)
R/W
0x0E
0x0F
00000000
0x00
HPF data out and dynamic range settings
XYZ_DATA_CFG
(3)(4)
HP_FILTER_CUTOFF
(3)(4)
PL_STATUS(1)(2)
PL_CFG
(3)(4)
(3)(4)
0x01
Real time status
R/W
0x0F
0x10
00000000
0x00
Cutoff frequency is set to 16 Hz @ 800 Hz
R
0x10
0x11
00000000
0x00
Landscape/portrait orientation status
R/W
0x11
0x12
10000000
0x80
Landscape/portrait configuration.
R
0x12
0x13
00000000
0x00
Landscape/portrait debounce counter
(3)(4)
R
0x13
0x14
01000100
0x44
Back/front, Z-lock trip threshold
P_L_THS_REG(3)(4)
PL_COUNT
PL_BF_ZCOMP
R
0x14
0x15
10000100
0x84
Portrait to landscape trip angle is 29°
(3)(4)
R/W
0x15
0x16
00000000
0x00
Freefall/motion functional block configuration
(1)(2)
R
0x16
0x17
00000000
0x00
Freefall/motion event source register
FF_MT_CFG
FF_MT_SRC
(3)(4)
R/W
0x17
0x18
00000000
0x00
Freefall/motion threshold register
FF_MT_COUNT(3)(4)
R/W
0x18
0x19
00000000
0x00
Freefall/motion debounce counter
Reserved
R
0x19 0x1C
—
—
—
TRANSIENT_CFG
R/W
0x1D
0x1E
00000000
0x00
Transient functional block configuration
TRANSIENT_SRC(1)(2)
R
0x1E
0x1F
00000000
0x00
Transient event status register
TRANSIENT_THS(3)(4)
R/W
0x1F
0x20
00000000
0x00
Transient event threshold
TRANSIENT_COUNT(3)(4)
R/W
0x20
0x21
00000000
0x00
Transient debounce counter
PULSE_CFG(3)(4)
R/W
0x21
0x22
00000000
0x00
ELE, Double_XYZ or Single_XYZ
PULSE_SRC(1)(2)
R
0x22
0x23
00000000
0x00
EA, Double_XYZ or Single_XYZ
PULSE_THSX(3)(4)
R/W
0x23
0x24
00000000
0x00
X pulse threshold
PULSE_THSY(3)(4)
R/W
0x24
0x25
00000000
0x00
Y pulse threshold
PULSE_THSZ(3)(4)
R/W
0x25
0x26
00000000
0x00
Z pulse threshold
PULSE_TMLT(3)(4)
R/W
0x26
0x27
00000000
0x00
Time limit for pulse
PULSE_LTCY(3)(4)
R/W
0x27
0x28
00000000
0x00
Latency time for 2nd pulse
PULSE_WIND(3)(4)
R/W
0x28
0x29
00000000
0x00
Window time for 2nd pulse
ASLP_COUNT(3)(4)
R/W
0x29
0x2A
00000000
0x00
Counter setting for auto-sleep
CTRL_REG1(3)(4)
R/W
0x2A
0x2B
00000000
0x00
Data rate, active mode
CTRL_REG2(3)(4)
R/W
0x2B
0x2C
00000000
0x00
Sleep enable, OS modes, RST, ST
CTRL_REG3(3)(4)
R/W
0x2C
0x2D
00000000
0x00
Wake from sleep, IPOL, PP_OD
FF_MT_THS
Reserved. Read return 0x00.
MMA8452Q
Sensors
NXP Semiconductors
19
Table 11. Register address map (continued)
Name
Type
F_READ = 0
Default
Hex
value
F_READ = 1
Comment
CTRL_REG4(3)(4)
R/W
0x2D
0x2E
00000000
0x00
Interrupt enable register
CTRL_REG5(3)(4)
R/W
0x2E
0x2F
00000000
0x00
Interrupt pin (INT1/INT2) map
OFF_X(3)(4)
R/W
0x2F
0x30
00000000
0x00
X-axis offset adjust
OFF_Y(3)(4)
R/W
0x30
0x31
00000000
0x00
Y-axis offset adjust
OFF_Z(3)(4)
R/W
0x31
0x0D
00000000
0x00
Z-axis offset adjust
0x40 – 7F
—
—
—
Reserved (do not modify)
1.
2.
3.
4.
Auto-increment address
Register
address
Reserved. Read return 0x00.
Register contents are reset when transition from standby to active mode occurs.
This register data is only valid in active mode.
Register contents are preserved when transition from active to standby mode occurs.
Modification of this register’s contents can only occur when device is standby mode except CTRL_REG1 active bit and CTRL_REG2 RST bit.
Note: Auto-increment addresses which are not a simple increment are highlighted in bold. The auto-increment addressing is only enabled when
device registers are read using I2C burst-read mode. Therefore the internal storage of the auto-increment address is cleared whenever a
stop condition is detected.
6.1
Data registers
The following are the data registers for the MMA8452Q. For more information on data manipulation of the MMA8452Q, refer to
application note, AN4076.
0x00: STATUS data status register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ZYXOW
ZOW
YOW
XOW
ZYXDR
ZDR
YDR
XDR
Table 12. STATUS description
Field
ZYXOW
Description
X, Y, Z-axis data overwrite. Default value: 0
0: No data overwrite has occurred
1: Previous X, Y, or Z data was overwritten by new X, Y, or Z data before it was read
ZOW
Z-axis data overwrite. Default value: 0
0: No data overwrite has occurred
1: Previous Z-axis data was overwritten by new Z-axis data before it was read
YOW
Y-axis data overwrite. Default value: 0
0: No data overwrite has occurred
1: Previous Y-axis data was overwritten by new Y-axis data before it was read
XOW
X-axis data overwrite. Default value: 0
0: No data overwrite has occurred
1: Previous X-axis data was overwritten by new X-axis data before it was read
ZYXDR
X, Y, Z-axis new data ready. Default value: 0
0: No new set of data ready
1: A new set of data is ready
ZDR
Z-axis new data available. Default value: 0
0: No new Z-axis data is ready
1: A new Z-axis data is ready
YDR
Y-axis new data available. Default value: 0
0: No new Y-axis data ready
1: A new Y-axis data is ready
XDR
X-axis new data available. Default value: 0
0: No new X-axis data ready
1: A new X-axis data is ready
MMA8452Q
20
Sensors
NXP Semiconductors
ZYXOW is set whenever a new acceleration data is produced before completing the retrieval of the previous set. This event
occurs when the content of at least one acceleration data register (i.e., OUT_X, OUT_Y, OUT_Z) has been overwritten. ZYXOW
is cleared when the high-bytes of the acceleration data (OUT_X_MSB, OUT_Y_MSB, OUT_Z_MSB) of all the active channels are
read.
ZOW is set whenever a new acceleration sample related to the Z-axis is generated before the retrieval of the previous sample.
When this occurs the previous sample is overwritten. ZOW is cleared anytime OUT_Z_MSB register is read.
YOW is set whenever a new acceleration sample related to the Y-axis is generated before the retrieval of the previous sample.
When this occurs the previous sample is overwritten. YOW is cleared anytime OUT_Y_MSB register is read.
XOW is set whenever a new acceleration sample related to the X-axis is generated before the retrieval of the previous sample.
When this occurs the previous sample is overwritten. XOW is cleared anytime OUT_X_MSB register is read.
ZYXDR signals that a new sample for any of the enabled channels is available. ZYXDR is cleared when the high-bytes of the
acceleration data (OUT_X_MSB, OUT_Y_MSB, OUT_Z_MSB) of all the enabled channels are read.
ZDR is set whenever a new acceleration sample related to the Z-axis is generated. ZDR is cleared anytime OUT_Z_MSB register
is read.
YDR is set whenever a new acceleration sample related to the Y-axis is generated. YDR is cleared anytime OUT_Y_MSB register
is read.
XDR is set whenever a new acceleration sample related to the X-axis is generated. XDR is cleared anytime OUT_X_MSB register
is read.
Data registers: 0x01: OUT_X_MSB, 0x02: OUT_X_LSB, 0x03: OUT_Y_MSB, 0x04: OUT_Y_LSB, 0x05: OUT_Z_MSB, 0x06:
OUT_Z_LSB
These registers contain the X-axis, Y-axis, and Z-axis 12-bit output sample data expressed as 2's complement numbers. The
sample data output registers store the current sample data.
0x01: OUT_X_MSB: X_MSB register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
XD11
XD10
XD9
XD8
XD7
XD6
XD5
XD4
0x02: OUT_X_LSB: X_LSB register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
XD3
XD2
XD1
XD0
0
0
0
0
0x03: OUT_Y_MSB: Y_MSB register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
YD11
YD10
YD9
YD8
YD7
YD6
YD5
YD4
0x04: OUT_Y_LSB: Y_LSB register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
YD3
YD2
XD1
XD0
0
0
0
0
0x05: OUT_Z_MSB: Z_MSB register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ZD11
ZD10
ZD9
ZD8
ZD7
ZD6
ZD5
ZD4
0x06: OUT_Z_LSB: Z_LSB register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ZD3
ZD2
ZD1
ZD0
0
0
0
0
OUT_X_MSB, OUT_X_LSB, OUT_Y_MSB, OUT_Y_LSB, OUT_Z_MSB, and OUT_Z_LSB are stored in the auto-incrementing
address range of 0x01 to 0x06 to reduce reading the status followed by 12-bit axis data to seven bytes. If the F_READ bit is set
(0x2A bit 1), auto-increment will skip over LSB registers. This will shorten the data acquisition from seven bytes to four bytes.
The LSB registers can only be read immediately following the read access of the corresponding MSB register. A random read
access to the LSB registers is not possible. Reading the MSB register and then the LSB register in sequence ensures that both
bytes (LSB and MSB) belong to the same data sample, even if a new data sample arrives between reading the MSB and the LSB
byte.
MMA8452Q
Sensors
NXP Semiconductors
21
0x0B: SYSMOD system mode register
The system mode register indicates the current device operating mode. Applications using the auto-sleep/wake mechanism
should use this register to synchronize the application with the device operating mode transitions.
0x0B: SYSMOD: system mode register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
0
SYSMOD1
SYSMOD0
Table 13. SYSMOD description
Field
SYSMOD[1:0]
Description
System mode. Default value: 00.
00: Standby mode
01: Wake mode
10: Sleep mode
0x0C: INT_SOURCE system interrupt status register
In the interrupt source register the status of the various embedded features can be determined. The bits that are set (logic ‘1’)
indicate which function has asserted an interrupt and conversely the bits that are cleared (logic ‘0’) indicate which function has
not asserted or has deasserted an interrupt. The bits are set by a low to high transition and are cleared by reading the
appropriate interrupt source register. The SRC_DRDY bit is cleared by reading the X, Y and Z data. It is not cleared by simply
reading the status register (0x00).
0x0C: INT_SOURCE: system interrupt status register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
SRC_ASLP
0
SRC_TRANS
SRC_LNDPRT
SRC_PULSE
SRC_FF_MT
0
SRC_DRDY
Table 14. INT_SOURCE description
Field
Description
SRC_ASLP
Auto-sleep/wake interrupt status bit. Default value: 0.
Logic ‘1’ indicates that an interrupt event that can cause a wake to sleep or sleep to wake system mode transition has
occurred.
Logic ‘0’ indicates that no wake to sleep or sleep to wake system mode transition interrupt event has occurred.
wake to sleep transition occurs when no interrupt occurs for a time period that exceeds the user specified limit
(ASLP_COUNT). This causes the system to transition to a user specified low ODR setting.
sleep to wake transition occurs when the user specified interrupt event has woken the system; thus causing the system
to transition to a user specified high ODR setting.
Reading the SYSMOD register clears the SRC_ASLP bit.
SRC_TRANS
Transient interrupt status bit. Default value: 0.
Logic ‘1’ indicates that an acceleration transient value greater than user specified threshold has occurred. Logic ‘0’
indicates that no transient event has occurred.
This bit is asserted whenever EA bit in the TRANS_SRC is asserted and the interrupt has been enabled. This bit is
cleared by reading the TRANS_SRC register.
SRC_LNDPRT
Landscape/portrait orientation interrupt status bit. Default value: 0.
Logic ‘1’ indicates that an interrupt was generated due to a change in the device orientation status. Logic ‘0’ indicates
that no change in orientation status was detected.
This bit is asserted whenever NEWLP bit in the PL_STATUS is asserted and the interrupt has been enabled.
This bit is cleared by reading the PL_STATUS register.
SRC_PULSE
Pulse interrupt status bit. Default value: 0.
Logic ‘1’ indicates that an interrupt was generated due to single and/or double pulse event. Logic ‘0’ indicates that no
pulse event was detected.
This bit is asserted whenever EA bit in the PULSE_SRC is asserted and the interrupt has been enabled.
This bit is cleared by reading the PULSE_SRC register.
MMA8452Q
22
Sensors
NXP Semiconductors
Table 14. INT_SOURCE description (continued)
Field
Description
SRC_FF_MT
Freefall/motion interrupt status bit. Default value: 0.
Logic ‘1’ indicates that the freefall/motion function interrupt is active. Logic ‘0’ indicates that no freefall or motion event
was detected.
This bit is asserted whenever EA bit in the FF_MT_SRC register is asserted and the FF_MT interrupt has been enabled.
This bit is cleared by reading the FF_MT_SRC register.
SRC_DRDY
Data-ready interrupt bit status. Default value: 0.
Logic ‘1’ indicates that the X, Y, Z data-ready interrupt is active indicating the presence of new data and/or data overrun.
Otherwise if it is a logic ‘0’ the X, Y, Z interrupt is not active.
This bit is asserted when the ZYXOW and/or ZYXDR is set and the interrupt has been enabled.
This bit is cleared by reading the X, Y, and Z data.
0x0D: WHO_AM_I device ID register
The device identification register identifies the part. The default value is 0x2A. This value is factory programmed. Consult the
factory for custom alternate values.
0x0D: WHO_AM_I device ID register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
1
0
1
0
1
0
0x0E: XYZ_DATA_CFG register
The XYZ_DATA_CFG register sets the dynamic range and sets the high-pass filter for the output data. When the HPF_OUT bit
is set. The data registers 0x01 to 0x06 will contain high-pass filtered data when this bit is set.
0x0E: XYZ_DATA_CFG (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
HPF_OUT
0
0
FS1
FS0
Table 15. XYZ data configuration descriptions
Field
HPF_OUT
FS[1:0]
Description
Enable high-pass output data 1 = output data high-pass filtered. Default value: 0
Output buffer data format full scale. Default value: 00 (2 g).
The default full-scale value range is 2 g and the high-pass filter is disabled.
Table 16. Full-scale range
FS1
FS0
Full-scale range
0
0
2
0
1
4
1
0
8
1
1
Reserved
MMA8452Q
Sensors
NXP Semiconductors
23
0x0F: HP_FILTER_CUTOFF high-pass filter register
This register sets the high-pass filter cutoff frequency for removal of the offset and slower changing acceleration data. The output
of this filter is indicated by the data registers (0x01-0x06) when bit 4 (HPF_OUT) of register 0x0E is set. The filter cutoff options
change based on the data rate selected as shown in Table 18. For details of implementation on the high-pass filter, refer to NXP
application note AN4071.
0x0F: HP_FILTER_CUTOFF: high-pass filter register (read/write)
Bit 7
Bit 6
0
0
Bit 5
Bit 4
Pulse_HPF_BYP Pulse_LPF_EN
Bit 3
Bit 2
Bit 1
Bit 0
0
0
SEL1
SEL0
Table 17. High-pass filter cutoff register descriptions
Field
Description
Pulse_HPF_BYP
Pulse_LPF_EN
SEL[1:0]
Bypass high-pass filter for pulse processing function.
0: HPF enabled for pulse processing, 1: HPF bypassed for pulse processing
Default value: 0.
Enable low-pass filter for pulse processing function.
0: LPF disabled for pulse processing, 1: LPF enabled for pulse processing
Default value: 0.
HPF cutoff frequency selection.
Default value: 00 (see Table 18).
Table 18. High-pass filter cutoff options
SEL1
SEL0
800 Hz
400 Hz
200 Hz
100 Hz
50 Hz
12.5 Hz
6.25 Hz
1.56 Hz
Oversampling mode = normal
0
0
16 Hz
16 Hz
8 Hz
4 Hz
2 Hz
2 Hz
2 Hz
2 Hz
0
1
8 Hz
8 Hz
4 Hz
2 Hz
1 Hz
1 Hz
1 Hz
1 Hz
1
0
4 Hz
4 Hz
2 Hz
1 Hz
0.5 Hz
0.5 Hz
0.5 Hz
0.5 Hz
1
1
2 Hz
2 Hz
1 Hz
0.5 Hz
0.25 Hz
0.25 Hz
0.25 Hz
0.25 Hz
Oversampling mode = low noise low power
0
0
16 Hz
16 Hz
8 Hz
4 Hz
2 Hz
0.5 Hz
0.5 Hz
0.5 Hz
0
1
8 Hz
8 Hz
4 Hz
2 Hz
1 Hz
0.25 Hz
0.25 Hz
0.25 Hz
1
0
4 Hz
4 Hz
2 Hz
1 Hz
0.5 Hz
0.125 Hz
0.125 Hz
0.125 Hz
1
1
2 Hz
2 Hz
1 Hz
0.5 Hz
0.25 Hz
0.063 Hz
0.063 Hz
0.063 Hz
Oversampling mode = high resolution
0
0
16 Hz
16 Hz
16 Hz
16 Hz
16 Hz
16 Hz
16 Hz
16 Hz
0
1
8 Hz
8 Hz
8 Hz
8 Hz
8 Hz
8 Hz
8 Hz
8 Hz
1
0
4 Hz
4 Hz
4 Hz
4 Hz
4 Hz
4 Hz
4 Hz
4 Hz
1
1
2 Hz
2 Hz
2 Hz
2 Hz
2 Hz
2 Hz
2 Hz
2 Hz
Oversampling mode = low power
0
0
16 Hz
8 Hz
4 Hz
2 Hz
1 Hz
0.25 Hz
0.25 Hz
0.25 Hz
0
1
8 Hz
4 Hz
2 Hz
1 Hz
0.5 Hz
0.125 Hz
0.125 Hz
0.125 Hz
1
0
4 Hz
2 Hz
1 Hz
0.5 Hz
0.25 Hz
0.063 Hz
0.063 Hz
0.063 Hz
1
1
2 Hz
1 Hz
0.5 Hz
0.25 Hz
0.125 Hz
0.031 Hz
0.031 Hz
0.031 Hz
MMA8452Q
24
Sensors
NXP Semiconductors
6.2
Portrait/landscape embedded function registers
For more details on the meaning of the different user-configurable settings and for example code refer to NXP application note
AN4068.
0x10: PL_STATUS portrait/landscape status register
This status register can be read to get updated information on any change in orientation by reading bit 7, or on the specifics of
the orientation by reading the other bits. For further understanding of portrait up, portrait down, landscape left, landscape right,
back and front orientations please refer to Figure 3. The interrupt is cleared when reading the PL_STATUS register.
0x10: PL_STATUS register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
NEWLP
LO
0
0
0
LAPO[1]
LAPO[0]
BAFRO
Table 19. PL_STATUS register description
Field
NEWLP
Description
Landscape/portrait status change flag. Default value: 0.
0: No change, 1: BAFRO and/or LAPO and/or Z-tilt lockout value has changed
LO
Z-tilt angle lockout. Default value: 0.
0: Lockout condition has not been detected.
1: Z-tilt lockout trip angle has been exceeded. Lockout has been detected.
LAPO[1:0](1)
Landscape/portrait orientation. Default value: 00
00: Portrait up: Equipment standing vertically in the normal orientation
01: Portrait down: Equipment standing vertically in the inverted orientation
10: Landscape right: Equipment is in landscape mode to the right
11: Landscape left: Equipment is in landscape mode to the left.
BAFRO
Back or front orientation. Default value: 0
0: Front: Equipment is in the front facing orientation.
1: Back: Equipment is in the back facing orientation.
1. The default power up state is BAFRO = 0, LAPO = 0, and LO = 0.
NEWLP is set to 1 after the first orientation detection after a standby to active transition, and whenever a change in LO, BAFRO,
or LAPO occurs. NEWLP bit is cleared anytime PL_STATUS register is read. The orientation mechanism state change is limited
to a maximum 1.25 g. LAPO BAFRO and LO continue to change when NEWLP is set. The current position is locked if the
absolute value of the acceleration experienced on any of the three axes is greater than 1.25 g.
0x11: Portrait/landscape configuration register
This register enables the portrait/landscape function and sets the behavior of the debounce counter.
0x11: PL_CFG register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DBCNTM
PL_EN
0
0
0
0
0
0
Table 20. PL_CFG description
Field
DBCNTM
PL_EN
Description
Debounce counter mode selection. Default value: 1
0: Decrements debounce whenever condition of interest is no longer valid.
1: Clears counter whenever condition of interest is no longer valid.
Portrait/landscape detection enable. Default value: 0
0: Portrait/landscape detection is disabled.
1: Portrait/landscape detection is enabled.
MMA8452Q
Sensors
NXP Semiconductors
25
0x12: Portrait/landscape debounce counter
This register sets the debounce count for the orientation state transition. The minimum debounce latency is determined by the
data rate set by the product of the selected system ODR and PL_COUNT registers. Any transition from wake to sleep or vice
versa resets the internal landscape/portrait debounce counter. Note: The debounce counter weighting (time step) changes based
on the ODR and the oversampling mode. Table 22 explains the time step value for all sample rates and all oversampling modes.
0x12: PL_COUNT register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DBNCE[7]
DBNCE[6]
DBNCE[5]
DBNCE[4]
DBNCE[3]
DBNCE[2]
DBNCE[1]
DBNCE[0]
Table 21. PL_COUNT description
Field
DBCNE[7:0]
Description
Debounce count value. Default value: 0000_0000.
Table 22. PL_COUNT relationship with the ODR
Max time range (s)
Time step (ms)
ODR (Hz)
Normal
LPLN
HighRes
LP
Normal
LPLN
HighRes
LP
800
0.319
0.319
0.319
0.319
1.25
1.25
1.25
1.25
400
0.638
0.638
0.638
0.638
2.5
2.5
2.5
2.5
200
1.28
1.28
0.638
1.28
5
5
2.5
5
100
2.55
2.55
0.638
2.55
10
10
2.5
10
50
5.1
5.1
0.638
5.1
20
20
2.5
20
12.5
5.1
20.4
0.638
20.4
20
80
2.5
80
6.25
5.1
20.4
0.638
40.8
20
80
2.5
160
1.56
5.1
20.4
0.638
40.8
20
80
2.5
160
0x13: PL_BF_ZCOMP back/front and Z compensation register
The Z-lock angle compensation is set to 29°. The back to front trip angle is set to ±75°.
0x13: PL_BF_ZCOMP register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
BKFR[1]
BKFR[0]
0
0
0
ZLOCK[2]
ZLOCK[1]
ZLOCK[0]
Table 23. PL_BF_ZCOMP description
Field
BKFR[1:0]
ZLOCK[2:0]
Description
Back front trip angle fixed threshold = 01 which is ≥ ±75°.
Z-lock angle fixed threshold = 100 which is 29°.
Note: All angles are accurate to ±2°.
0x14: PL_THS_REG portrait/landscape threshold and hysteresis register
This register represents the portrait to landscape trip threshold.
0x14: PL_THS_REG register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
PL_THS[4]
PL_THS[3]
PL_THS[2]
PL_THS[1]
PL_THS[0]
HYS[2]
HYS[1]
HYS[0]
MMA8452Q
26
Sensors
NXP Semiconductors
Table 24. PL_THS_REG description
Field
Description
Portrait/landscape fixed threshold angle = 1_0000 (45°).
PL_THS[7:3]
This is a fixed angle added to the threshold angle for a smoother transition from portrait to landscape and landscape to portrait.
This angle is fixed at ±14°, which is 100.
HYS[2:0]
Table 25. Trip angles with hysteresis for 45° angle
6.3
Hysteresis
register value
Hysteresis
± angle range
Landscape to portrait
trip angle
Portrait to landscape
trip angle
4
±14
59°
31°
Motion and freefall embedded function registers
The freefall/motion function can be configured in either freefall or motion detection mode via the OAE configuration bit (0x15
bit 6). The freefall/motion detection block can be disabled by setting all three bits ZEFE, YEFE, and XEFE to zero.
Depending on the register bits ELE (0x15 bit 7) and OAE (0x15 bit 6), each of the freefall and motion detection block can operate
in four different modes:
Mode 1: Freefall detection with ELE = 0, OAE = 0
In this mode, the EA bit (0x16 bit 7) indicates a freefall event after the debounce counter is complete. The ZEFE, YEFE, and
XEFE control bits determine which axes are considered for the freefall detection. Once the EA bit is set, and DBCNTM = 0, the
EA bit can get cleared only after the delay specified by FF_MT_COUNT. This is because the counter is in decrement mode. If
DBCNTM = 1, the EA bit is cleared as soon as the freefall condition disappears, and will not be set again before the delay
specified by FF_MT_COUNT has passed. Reading the FF_MT_SRC register does not clear the EA bit. The event flags (0x16)
ZHE, ZHP, YHE, YHP, XHE, and XHP reflect the motion detection status (i.e. high-g event) without any debouncing, provided
that the corresponding bits ZEFE, YEFE, and/or XEFE are set.
Mode 2: Freefall detection with ELE = 1, OAE = 0
In this mode, the EA event bit indicates a freefall event after the debounce counter. Once the debounce counter reaches the time
value for the set threshold, the EA bit is set, and remains set until the FF_MT_SRC register is read. When the FF_MT_SRC
register is read, the EA bit and the debounce counter are cleared and a new event can only be generated after the delay specified
by FF_MT_CNT. The ZEFE, YEFE, and XEFE control bits determine which axes are considered for the freefall detection. While
EA = 0, the event flags ZHE, ZHP, YHE, YHP, XHE, and XHP reflect the motion detection status (i.e., high-g event) without any
debouncing, provided that the corresponding bits ZEFE, YEFE, and/or XEFE are set. The event flags ZHE, ZHP, YHE, YHP, XHE,
and XHP are latched when the EA event bit is set. The event flags ZHE, ZHP, YHE, YHP, XHE, and XHP will start changing only
after the FF_MT_SRC register has been read.
Mode 3: Motion detection with ELE = 0, OAE = 1
In this mode, the EA bit indicates a motion event after the debounce counter time is reached. The ZEFE, YEFE, and XEFE control
bits determine which axes are taken into consideration for motion detection. Once the EA bit is set, and DBCNTM = 0, the EA bit
can get cleared only after the delay specified by FF_MT_COUNT. If DBCNTM = 1, the EA bit is cleared as soon as the motion
high-g condition disappears. The event flags ZHE, ZHP, YHE, YHP, XHE, and XHP reflect the motion detection status (i.e., highg event) without any debouncing, provided that the corresponding bits ZEFE, YEFE, and/or XEFE are set. Reading the
FF_MT_SRC does not clear any flags, nor is the debounce counter reset.
Mode 4: Motion detection with ELE = 1, OAE = 1
In this mode, the EA bit indicates a motion event after debouncing. The ZEFE, YEFE, and XEFE control bits determine which
axes are taken into consideration for motion detection. Once the debounce counter reaches the threshold, the EA bit is set, and
remains set until the FF_MT_SRC register is read. When the FF_MT_SRC register is read, all register bits are cleared and the
debounce counter are cleared and a new event can only be generated after the delay specified by FF_MT_CNT. While the bit
EA is zero, the event flags ZHE, ZHP, YHE, YHP, XHE, and XHP reflect the motion detection status (i.e., high-g event) without
any debouncing, provided that the corresponding bits ZEFE, YEFE, and/or XEFE are set. When the EA bit is set, these bits keep
their current value until the FF_MT_SRC register is read.
MMA8452Q
Sensors
NXP Semiconductors
27
0x15: FF_MT_CFG freefall/motion configuration register
This is the freefall/motion configuration register for setting up the conditions of the freefall or motion function.
0x15: FF_MT_CFG register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ELE
OAE
ZEFE
YEFE
XEFE
0
0
0
Table 26. FF_MT_CFG description
Field
Description
ELE
Event latch enable: Event flags are latched into FF_MT_SRC register. Reading of the FF_MT_SRC register clears the event
flag EA and all FF_MT_SRC bits. Default value: 0.
0: Event flag latch disabled; 1: Event flag latch enabled
OAE
Motion detect/freefall detect flag selection. Default value: 0. (freefall flag)
0: Freefall flag (logical AND combination)
1: Motion flag (logical OR combination)
ZEFE
Event flag enable on Z. Default value: 0.
0: Event detection disabled; 1: Raise event flag on measured acceleration value beyond preset threshold
YEFE
Event flag enable on Y event. Default value: 0.
0: Event detection disabled; 1: Raise event flag on measured acceleration value beyond preset threshold
XEFE
Event flag enable on X event. Default value: 0.
0: Event detection disabled; 1: Raise event flag on measured acceleration value beyond preset threshold
OAE bit allows the selection between motion (logical OR combination) and freefall (logical AND combination) detection.
ELE denotes whether the enabled event flag will to be latched in the FF_MT_SRC register or the event flag status in the
FF_MT_SRC will indicate the real-time status of the event. If ELE bit is set to a logic ‘1’, then the event flags are frozen when the
EA bit gets set, and are cleared by reading the FF_MT_SRC source register.
ZHFE, YEFE, XEFE enable the detection of a motion or freefall event when the measured acceleration data on X, Y, Z channel
is beyond the threshold set in FF_MT_THS register. If the ELE bit is set to logic ‘1’ in the FF_MT_CFG register new event flags
are blocked from updating the FF_MT_SRC register.
FF_MT_THS is the threshold register used to detect freefall motion events. The unsigned 7-bit FF_MT_THS threshold register
holds the threshold for the freefall detection where the magnitude of the X and Y and Z acceleration values is lower or equal than
the threshold value. Conversely, the FF_MT_THS also holds the threshold for the motion detection where the magnitude of the
X or Y or Z acceleration value is higher than the threshold value.
+8 g
X, Y, Z High-g Region
High-g + Threshold (Motion)
Positive
Acceleration
Low-g Threshold (Freefall)
X, Y, Z Low-g Region
High-g - Threshold (Motion)
X, Y, Z High-g Region
Negative
Acceleration
–8 g
Figure 12. FF_MT_CFG high- and low-g level
0x16: FF_MT_SRC freefall/motion source register
0x16: FF_MT_SRC freefall and motion source register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
EA
0
ZHE
ZHP
YHE
YHP
XHE
XHP
MMA8452Q
28
Sensors
NXP Semiconductors
Table 27. Freefall/motion source description
Field
EA
Description
Event active flag. Default value: 0.
0: No event flag has been asserted; 1: One or more event flag has been asserted.
See the description of the OAE bit to determine the effect of the 3-axis event flags on the EA bit.
ZHE
Z-motion flag. Default value: 0.
0: No Z-motion event detected, 1: Z motion has been detected
This bit reads always zero if the ZEFE control bit is set to zero
ZHP
Z-motion polarity flag. Default value: 0.
0: Z event was positive g, 1: Z event was negative g
This bit read always zero if the ZEFE control bit is set to zero
YHE
Y-motion flag. Default value: 0.
0: No Y-motion event detected, 1: Y motion has been detected
This bit read always zero if the YEFE control bit is set to zero
YHP
Y-motion polarity flag. Default value: 0
0: Y event detected was positive g, 1: Y event was negative g
This bit reads always zero if the YEFE control bit is set to zero
XHE
X-motion flag. Default value: 0
0: No X-motion event detected, 1: X motion has been detected
This bit reads always zero if the XEFE control bit is set to zero
XHP
X-motion polarity flag. Default value: 0
0: X event was positive g, 1: X event was negative g
This bit reads always zero if the XEFE control bit is set to zero
This register keeps track of the acceleration event which is triggering (or has triggered, in case of ELE bit in FF_MT_CFG register
being set to 1) the event flag. In particular EA is set to a logic ‘1’ when the logical combination of acceleration events flags
specified in FF_MT_CFG register is true. This bit is used in combination with the values in INT_EN_FF_MT and
INT_CFG_FF_MT register bits to generate the freefall/motion interrupts.
An X,Y, or Z motion is true when the acceleration value of the X or Y or Z channel is higher than the preset threshold value defined
in the FF_MT_THS register.
Conversely an X, Y, and Z low event is true when the acceleration value of the X and Y and Z channel is lower than or equal to
the preset threshold value defined in the FF_MT_THS register.
0x17: FF_MT_THS freefall and motion threshold register
0x17: FF_MT_THS register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DBCNTM
THS6
THS5
THS4
THS3
THS2
THS1
THS0
Table 28. FF_MT_THS description
Field
Description
DBCNTM
Debounce counter mode selection. Default value: 0.
0: Increments or decrements debounce, 1: Increments or clears counter.
THS[6:0]
Freefall/motion threshold: Default value: 000_0000.
The threshold resolution is 0.063 g/LSB and the threshold register has a range of 0 to 127 counts. The maximum range is to 8 g.
Note that even when the full scale value is set to 2 g or 4 g the motion detects up to 8 g. If the low-noise bit is set in register 0x2A
then the maximum threshold will be limited to 4 g regardless of the full-scale range.
DBCNTM bit configures the way in which the debounce counter is reset when the inertial event of interest is momentarily not true.
When DBCNTM bit is a logic ‘1’, the debounce counter is cleared to 0 whenever the inertial event of interest is no longer true as
shown in Figure 13, (b). While the DBCNTM bit is set to logic ‘0’ the debounce counter is decremented by 1 whenever the inertial
event of interest is no longer true (Figure 13, (c)) until the debounce counter reaches 0 or the inertial event of interest becomes
active.
Decrementing the debounce counter acts as a median enabling the system to filter out irregular spurious events which might
impede the detection of inertial events.
MMA8452Q
Sensors
NXP Semiconductors
29
0x18: FF_MT_COUNT debounce register
This register sets the number of debounce sample counts for the event trigger.
0x18: FF_MT_COUNT register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
D7
D6
D5
D4
D3
D2
D1
D0
Table 29. FF_MT_COUNT description
Field
Description
Count value. Default value: 0000_0000
D[7:0]
This register sets the minimum number of debounce sample counts of continuously matching the detection condition user
selected for the freefall, motion event.
When the internal debounce counter reaches the FF_MT_COUNT value a freefall/motion event flag is set. The debounce counter
will never increase beyond the FF_MT_COUNT value. Time step used for the debounce sample count depends on the ODR
chosen and the oversampling mode as shown in Table 30.
Table 30. FF_MT_COUNT relationship with the ODR
Max time range (s)
Time step (ms)
ODR (Hz)
Normal
LPLN
HighRes
LP
Normal
LPLN
HighRes
LP
800
0.319
0.319
0.319
0.319
1.25
1.25
1.25
1.25
400
0.638
0.638
0.638
0.638
2.5
2.5
2.5
2.5
200
1.28
1.28
0.638
1.28
5
5
2.5
5
100
2.55
2.55
0.638
2.55
10
10
2.5
10
50
5.1
5.1
0.638
5.1
20
20
2.5
20
12.5
5.1
20.4
0.638
20.4
20
80
2.5
80
6.25
5.1
20.4
0.638
40.8
20
80
2.5
160
1.56
5.1
20.4
0.638
40.8
20
80
2.5
160
MMA8452Q
30
Sensors
NXP Semiconductors
High-g Event on
all 3-axis
(Motion Detect)
Count Threshold
(a)
FF
Counter
Value
FFEA
High-g Event on
all 3-axis
(Motion Detect)
DBCNTM = 1
Count Threshold
Debounce
Counter
Value
(b)
EA
High-g Event on
all 3-axis
(Motion Detect)
DBCNTM = 0
Count Threshold
Debounce
Counter
Value
(c)
EA
Figure 13. DBCNTM bit function
MMA8452Q
Sensors
NXP Semiconductors
31
6.4
Transient (HPF) acceleration detection
For more information on the uses of the transient function please review NXP application note AN4071. This function is similar
to the motion detection except that high-pass filtered data is compared. There is an option to disable the high-pass filter through
the function. In this case the behavior is the same as the motion detection. This allows for the device to have two motion detection
functions.
0x1D: Transient_CFG register
The transient detection mechanism can be configured to raise an interrupt when the magnitude of the high-pass filtered
acceleration threshold is exceeded. The TRANSIENT_CFG register is used to enable the transient interrupt generation
mechanism for the three axes (X, Y, Z) of acceleration. There is also an option to bypass the high-pass filter. When the high-pass
filter is bypassed, the function behaves similar to the motion detection.
0x1D: TRANSIENT_CFG register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
ELE
ZTEFE
YTEFE
XTEFE
HPF_BYP
Table 31. TRANSIENT_CFG description
Field
Description
ELE
Transient event flags are latched into the TRANSIENT_SRC register. Reading of the TRANSIENT_SRC register clears the event
flag. Default value: 0.
0: Event flag latch disabled; 1: Event flag latch enabled
ZTEFE
Event flag enable on Z-transient acceleration greater than transient threshold event. Default value: 0.
0: Event detection disabled; 1: Raise event flag on measured acceleration delta value greater than transient threshold.
YTEFE
Event flag enable on Y-transient acceleration greater than transient threshold event. Default value: 0.
0: Event detection disabled; 1: Raise event flag on measured acceleration delta value greater than transient threshold.
XTEFE
Event flag enable on X-transient acceleration greater than transient threshold event. Default value: 0.
0: Event detection disabled; 1: Raise event flag on measured acceleration delta value greater than transient threshold.
HPF_BYP
Bypass high-pass filter. Default value: 0.
0: Data to transient acceleration detection block is through HPF; 1: Data to transient acceleration detection block is NOT through
HPF (similar to motion detection function)
0x1E: TRANSIENT_SRC register
The transient source register provides the status of the enabled axes and the polarity (directional) information. When this register
is read it clears the interrupt for the transient detection. When new events arrive while EA = 1, additional *TRANSE bits may get
set, and the corresponding *_Trans_Pol flag become updated. However, no *TRANSE bit may get cleared before the
TRANSIENT_SRC register is read.
0x1E: TRANSIENT_SRC register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
EA
ZTRANSE
Z_Trans_Pol
YTRANSE
Y_Trans_Pol
XTRANSE
X_Trans_Pol
Table 32. TRANSIENT_SRC description
Field
EA
ZTRANSE
Z_Trans_Pol
YTRANSE
Y_Trans_Pol
Description
Event active flag. Default value: 0.
0: No event flag has been asserted; 1: One or more event flag has been asserted.
Z-transient event. Default value: 0.
0: No interrupt, 1: Z-transient acceleration greater than the value of TRANSIENT_THS event has occurred
Polarity of Z-transient event that triggered interrupt. Default value: 0.
0: Z event was positive g, 1: Z event was negative I
Y-transient event. Default value: 0.
0: no interrupt, 1: Y-transient acceleration greater than the value of TRANSIENT_THS event has occurred
Polarity of Y-transient event that triggered interrupt. Default value: 0.
0: Y event was positive g, 1: Y event was negative g
MMA8452Q
32
Sensors
NXP Semiconductors
Table 32. TRANSIENT_SRC description (continued)
Field
XTRANSE
X_Trans_Pol
Description
X-transient event. Default value: 0.
0: No interrupt, 1: X-transient acceleration greater than the value of TRANSIENT_THS event has occurred
Polarity of X-transient event that triggered interrupt. Default value: 0.
0: X event was positive g, 1: X event was negative g
When the EA bit gets set while ELE = 1, all other status bits get frozen at their current state. By reading the TRANSIENT_SRC
register, all bits get cleared.
0x1F: TRANSIENT_THS register
The transient threshold register sets the threshold limit for the detection of the transient acceleration. The value in the
TRANSIENT_THS register corresponds to a g value which is compared against the values of high-pass filtered data. If the highpass filtered acceleration value exceeds the threshold limit, an event flag is raised and the interrupt is generated if enabled.
0x1F: TRANSIENT_THS register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DBCNTM
THS6
THS5
THS4
THS3
THS2
THS1
THS0
Table 33. TRANSIENT_THS description
Field
Description
DBCNTM
Debounce counter mode selection. Default value: 0. 0: increments or decrements debounce; 1: increments or clears counter.
THS[6:0]
Transient threshold: Default value: 000_0000.
The threshold THS[6:0] is a 7-bit unsigned number, 0.063 g/LSB. The maximum threshold is 8 g. Even if the part is set to full
scale at 2 g or 4 g this function will still operate up to 8 g. If the low-noise bit is set in register 0x2A, the maximum threshold to be
reached is 4 g.
Note: If configuring the transient detection threshold for less than 1 g, the high-pass filter will need some settling time. The settling
time will vary depending on selected ODR, high-pass frequency cutoff and threshold. For more information, please refer to NXP
application note AN4071.
0x20: TRANSIENT_COUNT
The TRANSIENT_COUNT sets the minimum number of debounce counts continuously matching the condition where the
unsigned value of high-pass filtered data is greater than the user specified value of TRANSIENT_THS.
0x20: TRANSIENT_COUNT register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
D7
D6
D5
D4
D3
D2
D1
D0
Table 34. TRANSIENT_COUNT description
Field
D[7:0]
Description
Count value. Default value: 0000_0000.
The time step for the transient detection debounce counter is set by the value of the system ODR and the oversampling mode.
Table 35. TRANSIENT_COUNT relationship with the ODR
Max time range (s)
Time step (ms)
ODR (Hz)
Normal
LPLN
HighRes
LP
Normal
LPLN
HighRes
LP
800
0.319
0.319
0.319
0.319
1.25
1.25
1.25
1.25
400
0.638
0.638
0.638
0.638
2.5
2.5
2.5
2.5
200
1.28
1.28
0.638
1.28
5
5
2.5
5
100
2.55
2.55
0.638
2.55
10
10
2.5
10
50
5.1
5.1
0.638
5.1
20
20
2.5
20
MMA8452Q
Sensors
NXP Semiconductors
33
Table 35. TRANSIENT_COUNT relationship with the ODR (continued)
Max time range (s)
Time step (ms)
ODR (Hz)
Normal
LPLN
HighRes
LP
Normal
LPLN
HighRes
LP
12.5
5.1
20.4
0.638
20.4
20
80
2.5
80
6.25
5.1
20.4
0.638
40.8
20
80
2.5
160
1.56
5.1
20.4
0.638
40.8
20
80
2.5
160
6.5
Single, double and directional pulse-detection registers
For more details of how to configure the pulse detection and sample code, please refer to NXP application note AN4072. The
pulse-detection registers are referred to as pulse.
0x21: PULSE_CFG pulse configuration register
This register configures the event flag for the pulse detection for enabling/disabling the detection of a single and double pulse on
each of the axes.
0x21: PULSE_CFG Register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DPA
ELE
ZDPEFE
ZSPEFE
YDPEFE
YSPEFE
XDPEFE
XSPEFE
Table 36. PULSE_CFG description
Field
Description
DPA
Double-pulse abort. Default value: 0.
0: Double-pulse detection is not aborted if the start of a pulse is detected during the time period specified by the PULSE_LTCY register.
1: Setting the DPA bit momentarily suspends the double pulse detection if the start of a pulse is detected during the time period
specified by the PULSE_LTCY register and the pulse ends before the end of the time period specified by the PULSE_LTCY register.
ELE
Pulse event flags are latched into the PULSE_SRC register. Reading of the PULSE_SRC register clears the event flag.
Default value: 0.
0: Event flag latch disabled; 1: Event flag latch enabled
ZDPEFE
Event flag enable on double pulse event on Z-axis. Default value: 0.
0: Event detection disabled; 1: Event detection enabled
ZSPEFE
Event flag enable on single pulse event on Z-axis. Default value: 0.
0: Event detection disabled; 1: Event detection enabled
YDPEFE
Event flag enable on double pulse event on Y-axis. Default value: 0.
0: Event detection disabled; 1: Event detection enabled
YSPEFE
Event flag enable on single pulse event on Y-axis. Default value: 0.
0: Event detection disabled; 1: Event detection enabled
XDPEFE
Event flag enable on double pulse event on X-axis. Default value: 0.
0: Event detection disabled; 1: Event detection enabled
XSPEFE
Event flag enable on single pulse event on X-axis. Default value: 0.
0: Event detection disabled; 1: Event detection enabled
0x22: PULSE_SRC pulse source register
This register indicates a double or single pulse event has occurred and also which direction. The corresponding axis and event
must be enabled in register 0x21 for the event to be seen in the source register.
0x22: PULSE_SRC register (read only)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
EA
AxZ
AxY
AxX
DPE
PolZ
PolY
PolX
MMA8452Q
34
Sensors
NXP Semiconductors
Table 37. PULSE_SRC description
Field
Description
EA
Event active flag. Default value: 0.
(0: No interrupt has been generated; 1: One or more interrupt events have been generated)
AxZ
Z-axis event. Default value: 0.
(0: No interrupt; 1: Z-axis event has occurred)
AxY
Y-axis event. Default value: 0.
(0: No interrupt; 1: Y-axis event has occurred)
AxX
X-axis event. Default value: 0.
(0: No interrupt; 1: X-axis event has occurred)
DPE
Double pulse on first event. Default value: 0.
(0: Single-pulse event triggered interrupt; 1: Double pulse event triggered interrupt)
PolZ
Pulse polarity of Z-axis event. Default value: 0.
(0: Pulse event that triggered interrupt was positive; 1: Pulse event that triggered interrupt was negative)
PolY
Pulse polarity of Y-axis event. Default value: 0.
(0: Pulse event that triggered interrupt was positive; 1: Pulse event that triggered interrupt was negative)
PolX
Pulse polarity of X-axis event. Default value: 0.
(0: Pulse event that triggered interrupt was positive; 1: Pulse event that triggered interrupt was negative)
When the EA bit gets set while ELE = 1, all status bits (AxZ, AxY, AxZ, DPE, and PolX, PolY, PolZ) are frozen. Reading the
PULSE_SRC register clears all bits. Reading the source register will clear the interrupt.
0x23 - 0x25: PULSE_THSX, Y, Z pulse threshold for X, Y and Z registers
The pulse threshold can be set separately for the X, Y and Z axes. The PULSE_THSX, PULSE_THSY and PULSE_THSZ
registers define the threshold which is used by the system to start the pulse detection procedure.
0x23: PULSE_THSX register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
THSX6
THSX5
THSX4
THSX3
THSX2
THSX1
THSX0
Table 38. PULSE_THSX description
Field
Description
Pulse threshold on X-axis. Default value: 000_0000.
THSX[6:0]
0x24: PULSE_THSY register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
THSY6
THSY5
THSY4
THSY3
THSY2
THSY1
THSY0
Table 39. PULSE_THSY description
Field
Description
Pulse threshold on Y-axis. Default value: 000_0000.
THSY[6:0]
0x25: PULSE_THSZ register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
THSZ6
THSZ5
THSZ4
THSZ3
THSZ2
THSZ1
THSZ0
Table 40. PULSE_THSZ description
Field
THSZ[6:0]
Description
Pulse threshold on Z-axis. Default value: 000_0000.
MMA8452Q
Sensors
NXP Semiconductors
35
The threshold values range from 1 to 127 with steps of 0.063 g/LSB at a fixed 8 g acceleration range, thus the minimum resolution
is always fixed at 0.063 g/LSB. If the low-noise bit in register 0x2A is set then the maximum threshold will be 4 g. The
PULSE_THSX, PULSE_THSY and PULSE_THSZ registers define the threshold which is used by the system to start the pulse
detection procedure. The threshold value is expressed over 7-bits as an unsigned number.
0x26: PULSE_TMLT pulse time window 1 register
0x26: PULSE_TMLT register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TMLT7
TMLT6
TMLT5
TMLT4
TMLT3
TMLT2
TMLT1
TMLT0
Table 41. PULSE_TMLT description
Field
TMLT[7:0]
Description
Pulse time limit. Default value: 0000_0000.
The bits TMLT7 through TMLT0 define the maximum time interval that can elapse between the start of the acceleration on the
selected axis exceeding the specified threshold and the end when the acceleration on the selected axis must go below the
specified threshold to be considered a valid pulse.
The minimum time step for the pulse time limit is defined in Table 42 and Table 43. Maximum time for a given ODR and
oversampling mode is the time step pulse multiplied by 255. The time steps available are dependent on the oversampling mode
and whether the pulse low-pass filter option is enabled or not. The pulse low-pass filter is set in register 0x0F.
Table 42. Time Step for pulse time limit (register 0x0F) Pulse_LPF_EN = 1
Max time range (s)
Time step (ms)
ODR (Hz)
Normal
LPLN
HighRes
LP
Normal
LPLN
HighRes
LP
800
0.319
0.319
0.319
0.319
1.25
1.25
1.25
1.25
400
0.638
0.638
0.638
0.638
2.5
2.5
2.5
2.5
200
1.28
1.28
0.638
1.28
5
5
2.5
5
100
2.55
2.55
0.638
2.55
10
10
2.5
10
50
5.1
5.1
0.638
5.1
20
20
2.5
20
12.5
5.1
20.4
0.638
20.4
20
80
2.5
80
6.25
5.1
20.4
0.638
40.8
20
80
2.5
160
1.56
5.1
20.4
0.638
40.8
20
80
2.5
160
Table 43. Time step for pulse time limit (register 0x0F) Pulse_LPF_EN = 0
Max time range (s)
Time step (ms)
ODR (Hz)
Normal
LPLN
HighRes
LP
Normal
LPLN
HighRes
LP
800
0.159
0.159
0.159
0.159
0.625
0.625
0.625
0.625
400
0.159
0.159
0.159
0.319
0.625
0.625
0.625
1.25
200
0.319
0.319
0.159
0.638
1.25
1.25
0.625
2.5
100
0.638
0.638
0.159
1.28
2.5
2.5
0.625
5
50
1.28
1.28
0.159
2.55
5
5
0.625
10
12.5
1.28
5.1
0.159
10.2
5
20
0.625
40
6.25
1.28
5.1
0.159
10.2
5
20
0.625
40
1.56
1.28
5.1
0.159
10.2
5
20
0.625
40
MMA8452Q
36
Sensors
NXP Semiconductors
0x27: PULSE_LTCY pulse latency timer register
0x27: PULSE_LTCY register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
LTCY7
LTCY6
LTCY5
LTCY4
LTCY3
LTCY2
LTCY1
LTCY0
Table 44. PULSE_LTCY description
Field
LTCY[7:0]
Description
Latency time limit. Default value: 0000_0000
The bits LTCY7 through LTCY0 define the time interval that starts after the first pulse detection. During this time interval, all pulses
are ignored. Note: This timer must be set for single pulse and for double pulse.
The minimum time step for the pulse latency is defined in Table 45 and Table 46. The maximum time is the time step at the ODR
and oversampling mode multiplied by 255. The timing also changes when the pulse LPF is enabled or disabled.
Table 45. Time step for pulse latency @ ODR and power mode (register 0x0F) Pulse_LPF_EN = 1
Max time range (s)
Time step (ms)
ODR (Hz)
Normal
LPLN
HighRes
LP
Normal
LPLN
HighRes
LP
800
0.638
0.638
0.638
0.638
2.5
2.5
2.5
2.5
400
1.276
1.276
1.276
1.276
5
5
5
5
200
2.56
2.56
1.276
2.56
10
10
5
10
100
5.1
5.1
1.276
5.1
20
20
5
20
50
10.2
10.2
1.276
10.2
40
40
5
40
12.5
10.2
40.8
1.276
40.8
40
160
5
160
6.25
10.2
40.8
1.276
81.6
40
160
5
320
1.56
10.2
40.8
1.276
81.6
40
160
5
320
Table 46. Time step for pulse latency @ ODR and power mode (register 0x0F) Pulse_LPF_EN = 0
Max time range (s)
Time step (ms)
ODR (Hz)
Normal
LPLN
HighRes
LP
Normal
LPLN
HighRes
LP
800
0.318
0.318
0.318
0.318
1.25
1.25
1.25
1.25
400
0.318
0.318
0.318
0.638
1.25
1.25
1.25
2.5
200
0.638
0.638
0.318
1.276
2.5
2.5
1.25
5
100
1.276
1.276
0.318
2.56
5
5
1.25
10
50
2.56
2.56
0.318
5.1
10
10
1.25
20
12.5
2.56
10.2
0.318
20.4
10
40
1.25
80
6.25
2.56
10.2
0.318
20.4
10
40
1.25
80
1.56
2.56
10.2
0.318
20.4
10
40
1.25
80
MMA8452Q
Sensors
NXP Semiconductors
37
0x28: PULSE_WIND register (read/write)
0x28: PULSE_WIND second pulse time window register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
WIND7
WIND6
WIND5
WIND4
WIND3
WIND2
WIND1
WIND0
Table 47. PULSE_WIND description
Field
WIND[7:0]
Description
Second pulse time window. Default value: 0000_0000.
The bits WIND7 through WIND0 define the maximum interval of time that can elapse after the end of the latency interval in which
the start of the second pulse event must be detected provided the device has been configured for double pulse detection. The
detected second pulse width must be shorter than the time limit constraints specified by the PULSE_TMLT register, but the end
of the double pulse need not finish within the time specified by the PULSE_WIND register.
The minimum time step for the pulse window is defined in Table 48 and Table 49. The maximum time is the time step at the ODR,
oversampling mode and LPF filter option multiplied by 255.
Table 48. Time step for PULSE detection window @ ODR and power mode (register 0x0F) Pulse_LPF_EN = 1
Max time range (s)
Time step (ms)
ODR (Hz)
Normal
LPLN
HighRes
LP
Normal
LPLN
HighRes
LP
800
0.638
0.638
0.638
0.638
2.5
2.5
2.5
2.5
400
1.276
1.276
1.276
1.276
5
5
5
5
200
2.56
2.56
1.276
2.56
10
10
5
10
100
5.1
5.1
1.276
5.1
20
20
5
20
50
10.2
10.2
1.276
10.2
40
40
5
40
12.5
10.2
40.8
1.276
40.8
40
160
5
160
6.25
10.2
40.8
1.276
81.6
40
160
5
320
1.56
10.2
40.8
1.276
81.6
40
160
5
320
Table 49. Time step for PULSE detection window @ ODR and power mode (register 0x0F) Pulse_LPF_EN = 0
Max time range (s)
Time step (ms)
ODR (Hz)
Normal
LPLN
HighRes
LP
Normal
LPLN
HighRes
LP
800
0.318
0.318
0.318
0.318
1.25
1.25
1.25
1.25
400
0.318
0.318
0.318
0.638
1.25
1.25
1.25
2.5
200
0.638
0.638
0.318
1.276
2.5
2.5
1.25
5
100
1.276
1.276
0.318
2.56
5
5
1.25
10
50
2.56
2.56
0.318
5.1
10
10
1.25
20
12.5
2.56
10.2
0.318
20.4
10
40
1.25
80
6.25
2.56
10.2
0.318
20.4
10
40
1.25
80
1.56
2.56
10.2
0.318
20.4
10
40
1.25
80
MMA8452Q
38
Sensors
NXP Semiconductors
6.6
Auto-wake/sleep detection
The ASLP_COUNT register sets the minimum time period of inactivity required to change current ODR value from the value
specified in the DR[2:0] register to ASLP_RATE register value, provided the SLPE bit is set to a logic ‘1’ in the CTRL_REG2
register. See Table 52 for functional blocks that may be monitored for inactivity in order to trigger the return to sleep event.
0x29: ASLP_COUNT Register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
D7
D6
D5
D4
D3
D2
D1
D0
Table 50. ASLP_COUNT description
Field
D[7:0]
Description
Duration value. Default value: 0000_0000.
D7-D0 defines the minimum duration time to change current ODR value from DR to ASLP_RATE. Time step and maximum value
depend on the ODR chosen as shown in Table 51.
Table 51. ASLP_COUNT r with ODR
Output data rate (ODR)
Duration
ODR time step
ASLP_COUNT step
800 Hz
0 to 81 s
1.25 ms
320 ms
400 Hz
0 to 81 s
2.5 ms
320 ms
200 Hz
0 to 81 s
5 ms
320 ms
100 Hz
0 to 81 s
10 ms
320 ms
50 Hz
0 to 81 s
20 ms
320 ms
12.5 Hz
0 to 81 s
80 ms
320 ms
6.25 Hz
0 to 81 s
160 ms
320 ms
1.56 Hz
0 to 162 s
640 ms
640 ms
Table 52. Sleep/wake mode gates and triggers
Interrupt source
Event restarts timer and
delays return to sleep
Event will wake from sleep
SRC_TRANS
Yes
Yes
SRC_LNDPRT
Yes
Yes
SRC_PULSE
Yes
Yes
SRC_FF_MT
Yes
Yes
SRC_ASLP
No*
No*
SRC_DRDY
No
No
In order to wake the device, the desired function or functions must be enabled in CTRL_REG4 and set to wake to sleep in
CTRL_REG3. All enabled functions will still function in sleep mode at the sleep ODR. Only the functions that have been selected
for wake from sleep will wake the device.
MMA8452Q has four functions that can be used to keep the sensor from falling asleep; transient, orientation, pulse, and motion/
FF. One or more of these functions can be enabled. In order to wake the device, four functions are provided; transient, orientation,
pulse, and the motion/freefall. The auto-wake/sleep interrupt does not affect the wake/sleep, nor does the data-ready interrupt.
See register 0x2C for the wake from sleep bits.
If the auto-sleep bit is disabled, then the device can only toggle between standby and wake mode. If auto-sleep interrupt is
enabled, transitioning from active mode to auto-sleep mode and vice versa generates an interrupt.
MMA8452Q
Sensors
NXP Semiconductors
39
6.7
Control registers
Note: Except for standby mode selection, the device must be in standby mode to change any of the fields within CTRL_REG1
(0X2A).
0x2A: CTRL_REG1 system control 1 register
0x2A: CTRL_REG1 register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ASLP_RATE1
ASLP_RATE0
DR2
DR1
DR0
LNOISE
F_READ
ACTIVE
Table 53. CTRL_REG1 description
Field
Description
ASLP_RATE[1:0]
Configures the auto-wake sample frequency when the device is in sleep mode. Default value: 00.
See Table 54 for more information.
DR[2:0]
Data rate selection. Default value: 000.
See Table 55 for more information.
LNOISE
Reduced noise reduced maximum range mode. Default value: 0.
(0: Normal mode; 1: Reduced noise mode)
F_READ
Fast-read mode: Data format limited to single byte. Default value: 0.
(0: Normal mode 1: Fast-read mode)
ACTIVE
Full-scale selection. Default value: 00.
(0: Standby mode; 1: Active mode)
Table 54. Sleep mode rate description
ASLP_RATE1
ASLP_RATE0
Frequency (Hz)
0
0
50
0
1
12.5
1
0
6.25
1
1
1.56
It is important to note that when the device is auto-sleep mode, the system ODR and the data rate for all the system functional
blocks are overridden by the data rate set by the ASLP_RATE field.
DR[2:0] bits select the output data rate (ODR) for acceleration samples. The default value is 000 for a data rate of 800 Hz.
Table 55. System output data rate selection
DR2
DR1
DR0
ODR
Period
0
0
0
800 Hz
1.25 ms
0
0
1
400 Hz
2.5 ms
0
1
0
200 Hz
5 ms
0
1
1
100 Hz
10 ms
1
0
0
50 Hz
20 ms
1
0
1
12.5 Hz
80 ms
1
1
0
6.25 Hz
160 ms
1
1
1
1.56 Hz
640 ms
MMA8452Q
40
Sensors
NXP Semiconductors
ACTIVE bit selects between standby mode and active mode. The default value is 0 for standby mode.
Table 56. Full-scale selection
Active
Mode
0
Standby
1
Active
LNOISE bit selects between normal full dynamic range mode and a high sensitivity, low noise mode. In low noise mode, the
maximum signal that can be measured is ±4 g. Note: Any thresholds set above 4 g will not be reached.
F_READ bit selects between normal and fast-read mode. When selected, the auto-increment counter will skip over the LSB data
bytes.
0x2B: CTRL_REG2 system control 2 register
0x2B: CTRL_REG2 register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
ST
RST
0
SMODS1
SMODS0
SLPE
MODS1
MODS0
Table 57. CTRL_REG2 description
Field
ST
RST
SMODS[1:0]
SLPE
MODS[1:0]
Description
Self-test enable. Default value: 0.
0: Self-test disabled; 1: Self-test enabled
Software reset. Default value: 0.
0: Device reset disabled; 1: Device reset enabled.
Sleep mode power scheme selection. Default value: 00.
See Table 58 and Table 59
Auto-sleep enable. Default value: 0.
0: Auto-sleep is not enabled;
1: Auto-sleep is enabled.
Active mode power scheme selection. Default value: 00.
See Table 58 and Table 59
ST bit activates the self-test function. When ST is set, X, Y, and Z outputs will shift. RST bit is used to activate the software reset.
The reset mechanism can be enabled in standby and active mode.
When the reset bit is enabled, all registers are rest and are loaded with default values. Writing ‘1’ to the RST bit immediately
resets the device, no matter whether it is in active/wake, active/sleep, or standby mode.
The I2C communication system is reset to avoid accidental corrupted data access.
At the end of the boot process the RST bit is deasserted to 0. Reading this bit will return a value of zero.
The (S)MODS[1:0] bits select which oversampling mode is to be used shown in Table 58. The oversampling modes are available
in both wake mode MOD[1:0] and also in the sleep mode SMOD[1:0].
Table 58. MODS oversampling modes
(S)MODS1
(S)MODS0
Power mode
0
0
Normal
0
1
Low Noise Low Power
1
0
High Resolution
1
1
Low Power
MMA8452Q
Sensors
NXP Semiconductors
41
Table 59. MODS oversampling modes current consumption and averaging values at each ODR
Mode
Normal (00)
Low Noise Low Power (01)
High Resolution (10)
Low Power (11)
ODR
Current μA
OS Ratio
Current μA
OS Ratio
Current μA
OS Ratio
Current μA
OS Ratio
1.56 Hz
24
128
8
32
165
1024
6
16
6.25 Hz
24
32
8
8
165
256
6
4
12.5 Hz
24
16
8
4
165
128
6
2
50 Hz
24
4
24
4
165
32
14
2
100 Hz
44
4
44
4
165
16
24
2
200 Hz
85
4
85
4
165
8
44
2
400 Hz
165
4
165
4
165
4
85
2
800 Hz
165
2
165
2
165
2
165
2
0x2C: CTRL_REG3 interrupt control register
0x2C: CTRL_REG3 register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
WAKE_TRANS
WAKE_LNDPRT
WAKE_PULSE
WAKE_FF_MT
0
IPOL
PP_OD
Table 60. CTRL_REG3 description
Field
Description
WAKE_TRANS
WAKE_LNDPRT
0: Transient function is bypassed in sleep mode. Default value: 0.
1: Transient function interrupt can wake up system
0: Orientation function is bypassed in sleep mode. Default value: 0.
1: Orientation function interrupt can wake up system
WAKE_PULSE
0: Pulse function is bypassed in sleep mode. Default value: 0.
1: Pulse function interrupt can wake up system
WAKE_FF_MT
0: Freefall/motion function is bypassed in sleep mode. Default value: 0.
1: Freefall/motion function interrupt can wake up
Interrupt polarity active high, or active low. Default value: 0.
0: Active low; 1: Active high
IPOL
Push-pull/open drain selection on interrupt pad. Default value: 0.
0: Push-pull; 1: Open drain
PP_OD
IPOL bit selects the polarity of the interrupt signal. When IPOL is ‘0’ (default value) any interrupt event will signaled with a
logical 0.
PP_OD bit configures the interrupt pin to push-pull or in open drain mode. The default value is 0 which corresponds to push-Pull
mode. The open drain configuration can be used for connecting multiple interrupt signals on the same interrupt line.
0x2D: CTRL_REG4 register (read/write)
0x2D: CTRL_REG4 register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INT_EN_ASLP
0
INT_EN_TRANS
INT_EN_LNDPRT
INT_EN_PULSE
INT_EN_FF_MT
0
INT_EN_DRDY
Table 61. Interrupt enable register description
Field
INT_EN_ASLP
INT_EN_TRANS
Description
Interrupt enable. Default value: 0.
0: Auto-sleep/wake interrupt disabled; 1: Auto-sleep/wake interrupt enabled.
Interrupt enable. Default value: 0.
0: Transient interrupt disabled; 1: Transient interrupt enabled.
MMA8452Q
42
Sensors
NXP Semiconductors
Table 61. Interrupt enable register description (continued)
Field
Description
INT_EN_LNDPRT
Interrupt enable. Default value: 0.
0: Orientation (landscape/portrait) interrupt disabled.
1: Orientation (landscape/portrait) interrupt enabled.
INT_EN_PULSE
Interrupt enable. Default value: 0.
0: Pulse detection interrupt disabled; 1: Pulse detection interrupt enabled
INT_EN_FF_MT
Interrupt enable. Default value: 0.
0: Freefall/motion interrupt disabled; 1: Freefall/motion interrupt enabled
INT_EN_DRDY
Interrupt enable. Default value: 0.
0: Data-ready interrupt disabled; 1: Data-ready interrupt enabled
The corresponding functional block interrupt enable bit allows the functional block to route its event detection flags to the system’s
interrupt controller. The interrupt controller routes the enabled functional block interrupt to the INT1 or INT2 pin.
0x2E: CTRL_REG5 register (read/write)
0x2E: CTRL_REG5 interrupt configuration register
Bit 7
Bit 6
INT_CFG_ASLP
0
Bit 5
Bit 4
Bit 3
Bit 2
INT_CFG_TRANS INT_CFG_LNDPRT INT_CFG_PULSE INT_CFG_FF_MT
Bit 1
Bit 0
0
INT_CFG_DRDY
Table 62. Interrupt configuration register description
Field
Description
INT_CFG_ASLP
INT1/INT2 configuration. Default value: 0.
0: Interrupt is routed to INT2 pin; 1: Interrupt is routed to INT1 pin
INT_CFG_TRANS
INT1/INT2 configuration. Default value: 0.
0: Interrupt is routed to INT2 pin; 1: Interrupt is routed to INT1 pin
INT_CFG_LNDPRT
INT1/INT2 configuration. Default value: 0.
0: Interrupt is routed to INT2 pin; 1: Interrupt is routed to INT1 pin
INT_CFG_PULSE
INT1/INT2 configuration. Default value: 0.
0: Interrupt is routed to INT2 pin; 1: Interrupt is routed to INT1 pin
INT_CFG_FF_MT
INT1/INT2 configuration. Default value: 0.
0: Interrupt is routed to INT2 pin; 1: Interrupt is routed to INT1 pin
INT_CFG_DRDY
INT1/INT2 configuration. Default value: 0.
0: Interrupt is routed to INT2 pin; 1: Interrupt is routed to INT1 pin
The system’s interrupt controller shown in Figure 10 uses the corresponding bit field in the CTRL_REG5 register to determine the
routing table for the INT1 and INT2 interrupt pins. If the bit value is logic ‘0’, the functional block’s interrupt is routed to INT2, and
if the bit value is logic ‘1’, then the interrupt is routed to INT1. One or more functions can assert an interrupt pin; therefore a host
application responding to an interrupt should read the INT_SOURCE (0x0C) register to determine the appropriate sources of the
interrupt.
6.8
User offset correction registers
For more information on how to calibrate the 0 g offset, refer to application note AN4069. The 2’s complement offset correction
registers values are used to realign the zero-g position of the X, Y, and Z-axis after device board mount. The resolution of the
offset registers is 2 mg per LSB. The 2’s complement 8-bit value would result in an offset compensation range ±256 mg.
0x2F: OFF_X offset correction X register
0x2F: OFF_X register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
D7
D6
D5
D4
D3
D2
D1
D0
MMA8452Q
Sensors
NXP Semiconductors
43
Table 63. OFF_X description
Field
Description
X-axis offset value. Default value: 0000_0000.
D[7:0]
0x30: OFF_Y offset correction Y register
0x30: OFF_Y register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
D7
D6
D5
D4
D3
D2
D1
D0
Table 64. OFF_Y description
Field
Description
Y-axis offset value. Default value: 0000_0000.
D[7:0]
0x31: OFF_Z offset correction Z register
0x31: OFF_Z register (read/write)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
D7
D6
D5
D4
D3
D2
D1
D0
Table 65. OFF_Z description
Field
Description
Z-axis offset value. Default value: 0000_0000.
D[7:0]
Table 66. MMA8452Q register map
Reg
Name
Definition
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
00
STATUS
Data Status R
ZYXOW
ZOW
YOW
XOW
ZYXDR
ZDR
YDR
XDR
01
OUT_X_MSB
12-bit X data R
XD11
XD10
XD9
XD8
XD7
XD6
XD5
XD4
02
OUT_X_LSB
12-bit X data R
XD3
XD2
XD1
XD0
0
0
0
0
03
OUT_Y_MSB
12-bit Y data R
YD11
YD10
YD9
YD8
YD7
YD6
YD5
YD4
04
OUT_Y_LSB
12-bit Y data R
YD3
YD2
YD1
YD0
0
0
0
0
05
OUT_Z_MSB
12-bit Z data R
ZD11
ZD10
ZD9
ZD8
ZD7
ZD6
ZD5
ZD4
06
OUT_Z_LSB
12-bit Z data R
ZD3
ZD2
ZD1
ZD0
0
0
0
0
0B
SYSMOD
System mode R
0
0
0
0
0
0
SYSMOD1
SYSMOD0
0C
INT_SOURCE
Interrupt Status R
SRC_ASLP
0
SRC_TRANS
SRC_LNDPRT
SRC_PULSE
SRC_FF_MT
0
SRC_DRDY
0D
WHO_AM_I
ID Register R
0
0
1
0
1
0
1
0
0E
XYZ_DATA_CFG
Data Config R/W
0
0
0
HPF_OUT
0
0
FS1
FS0
0F
HP_FILTER_CUTOFF
HP Filter Setting R/W
0
0
Pulse_HPF_BYP
Pulse_LPF_EN
0
0
SEL1
SEL0
10
PL_STATUS
PL Status R
NEWLP
LO
0
0
0
LAPO[1]
LAPO[0]
BAFRO
11
PL_CFG
PL Configuration R/W
DBCNTM
PL_EN
0
0
0
0
0
0
12
PL_COUNT
PL DEBOUNCE R/W
DBNCE[7]
DBNCE[6]
DBNCE[5]
DBNCE[4]
DBNCE[3]
DBNCE[2]
DBNCE[1]
DBNCE[0]
13
PL_BF_ZCOMP
PL Back/Front Z Comp
R
BKFR[1]
BKFR[0]
0
0
0
ZLOCK[2]
ZLOCK[1]
ZLOCK[0]
14
PL_THS_REG
PL THRESHOLD R
PL_THS[4]
PL_THS[3]
PL_THS[2]
PL_THS[1]
PL_THS[0]
HYS[2]
HYS[1]
HYS[0]
15
FF_MT_CFG
Freefall/Motion Config
R/W
ELE
OAE
ZEFE
YEFE
XEFE
0
0
0
16
FF_MT_SRC
Freefall/Motion Source
R
EA
0
ZHE
ZHP
YHE
YHP
XHE
XHP
17
FF_MT_THS
Freefall/Motion threshold
R/W
DBCNTM
THS6
THS5
THS4
THS3
THS2
THS1
THS0
MMA8452Q
44
Sensors
NXP Semiconductors
Table 66. MMA8452Q register map (continued)
Reg
Name
Definition
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
18
FF_MT_COUNT
Freefall/Motion
Debounce R/W
D7
D6
D5
D4
D3
D2
D1
D0
1D
TRANSIENT_CFG
Transient Config R/W
0
0
0
ELE
ZTEFE
YTEFE
XTEFE
HPF_BYP
1E
TRANSIENT_SRC
Transient Source R
0
EA
ZTRANSE
Z_Trans_Pol
YTRANSE
Y_Trans_Pol
XTRANSE
X_Trans_Pol
1F
TRANSIENT_THS
Transient threshold R/W
DBCNTM
THS6
THS5
THS4
THS3
THS2
THS1
THS0
20
TRANSIENT_COUNT
Transient Debounce
R/W
D7
D6
D5
D4
D3
D2
D1
D0
21
PULSE_CFG
Pulse Config R/W
DPA
ELE
ZDPEFE
ZSPEFE
YDPEFE
YSPEFE
XDPEFE
XSPEFE
22
PULSE_SRC
Pulse Source R
EA
AxZ
AxY
AxX
DPE
Pol_Z
Pol_Y
Pol_X
23
PULSE_THSX
Pulse X Threshold R/W
0
THSX6
THSX5
THSX4
THSX3
THSX2
THSX1
THSX0
24
PULSE_THSY
Pulse Y Threshold R/W
0
THSY6
THSY5
THSY4
THSY3
THSY2
THSY1
THSY0
25
PULSE_THSZ
Pulse Z Threshold R/W
0
THSZ6
THSZ5
THSZ4
THSZ3
THSZ2
THSZ1
THSZ0
26
PULSE_TMLT
Pulse First Timer R/W
TMLT7
TMLT6
TMLT5
TMLT4
TMLT3
TMLT2
TMLT1
TMLT0
27
PULSE_LTCY
Pulse Latency R/W
LTCY7
LTCY6
LTCY5
LTCY4
LTCY3
LTCY2
LTCY1
LTCY0
28
PULSE_WIND
Pulse 2nd Window
R/W
WIND7
WIND6
WIND5
WIND4
WIND3
WIND2
WIND1
WIND0
29
ASLP_COUNT
Auto-sleep Counter
R/W
D7
D6
D5
D4
D3
D2
D1
D0
2A
CTRL_REG1
Control Reg1 R/W
ASLP_RATE1
ASLP_RATE0
DR2
DR1
DR0
LNOISE
F_READ
ACTIVE
2B
CTRL_REG2
Control Reg2 R/W
ST
RST
0
SMODS1
SMODS0
SLPE
MODS1
MODS0
2C
CTRL_REG3
Control Reg3
(wake Interrupts from
sleep) R/W
0
WAKE_TRANS
WAKE_LNDPRT
WAKE_PULSE
WAKE_FF_MT
0
IPOL
PP_OD
2D
CTRL_REG4
Control Reg4
(Interrupt Enable Map)
R/W
INT_EN_ASLP
0
INT_EN_TRANS
INT_EN_LNDPRT
INT_EN_PULSE
INT_EN_FF_MT
0
INT_EN_DRDY
2E
CTRL_REG5
Control Reg5
(Interrupt Configuration)
R/W
INT_CFG_ASLP
0
INT_CFG_TRANS
INT_CFG_LNDPR
T
INT_CFG_PULSE
INT_CFG_FF_MT
0
INT_CFG_DRDY
2F
OFF_X
X 8-bit offset R/W
D7
D6
D5
D4
D3
D2
D1
D0
30
OFF_Y
Y 8-bit offset R/W
D7
D6
D5
D4
D3
D2
D1
D0
31
OFF_Z
Z 8-bit offset R/W
D7
D6
D5
D4
D3
D2
D1
D0
Table 67. Accelerometer output data
12-bit data
Range ±2 g (1 mg)
Range ±4 g (2 mg)
Range ±8 g (3.9 mg)
0111 1111 1111
1.999 g
+3.998 g
+7.996 g
0111 1111 1110
1.998 g
+3.996 g
+7.992 g
…
…
…
…
0000 0000 0001
0.001 g
+0.002 g
+0.004 g
0000 0000 0000
0.0000 g
0.0000 g
0.0000 g
1111 1111 1111
–0.001 g
–0.002 g
–0.004 g
…
…
…
…
1000 0000 0001
–1.999 g
–3.998 g
–7.996 g
1000 0000 0000
–2.0000 g
–4.0000 g
–8.0000 g
8-bit data
Range ±2 g (15.6 mg)
Range ±4 g (31.25 mg)
Range ±8 g (62.5 mg)
0111 1111
1.9844 g
+3.9688 g
+7.9375 g
0111 1110
1.9688 g
+3.9375 g
+7.8750 g
…
…
…
…
MMA8452Q
Sensors
NXP Semiconductors
45
Table 67. Accelerometer output data (continued)
0000 0001
+0.0156 g
+0.0313 g
+0.0625 g
0000 0000
0.000 g
0.0000 g
0.0000 g
1111 1111
–0.0156 g
–0.0313 g
–0.0625 g
…
…
…
…
1000 0001
–1.9844 g
–3.9688 g
–7.9375 g
1000 0000
–2.0000 g
–4.0000 g
–8.0000 g
MMA8452Q
46
Sensors
NXP Semiconductors
7
Printed Circuit Board Layout and Device Mounting
Printed Circuit Board (PCB) layout and device mounting are critical portions of the total design. The footprint for the surface mount
packages must be the correct size as a base for a proper solder connection between the PCB and the package. This, along with
the recommended soldering materials and techniques, will optimize assembly and minimize the stress on the package after board
mounting.
7.1
Printed circuit board layout
The following recommendations are a guide to an effective PCB layout. See Figure 14 for footprint dimensions.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Do not solder down exposed ad (EP) under the package to minimize board mounting stress impact to product
performance.
The solder mask should not cover any of the PCB landing pads, as shown in Figure 14.
No additional via nor metal pattern underneath package on the top of the PCB layer.
Do not place any components or vias within 2 mm of the package land area. This may cause additional package stress
if it is too close to the package land area.
Signal traces connected to pads should be as symmetric as possible. Put dummy traces on NC pads, to have same
length of exposed trace for all pads.
Use a standard pick and place process and equipment. Do not use a hand soldering process.
Customers are advised to be cautious about the proximity of screw down holes to the sensor, and the location of any
press fit to the assembled PCB when in an enclosure. It is important that the assembled PCB remain flat after
assembly to keep electronic operation of the device optimal.
The PCB should be rated for the multiple lead-free reflow condition with max 260 °C temperature.
NXP using halide-free molding compound (green) and lead-free terminations. These terminations are compatible with
tin-lead (Sn-Pb) as well as tin-silver-copper (Sn-Ag-Cu) solder paste soldering processes. Reflow profiles applicable to
those processes can be used successfully for soldering the devices.
MMA8452Q
Sensors
NXP Semiconductors
47
;
;
;
;
;
;
;
;
3DFNDJHIRRWSULQW
Package outline
3DFNDJH
3&%ODQGSDG
;
Package outline
;
3DFNDJHIRRWSULQW
;
;
;
;
;
3DFNDJHIRRWSULQW
Package outline
;
;
;
6ROGHUVWHQFLORSHQLQJ
6ROGHUPDVNRSHQLQJ
Figure 14. Footprint
7.2
Overview of soldering considerations
Information provided here is based on experiments executed on QFN devices. These experiments cannot represent exact
conditions present at a customer site. Therefore, information herein should be used for guidance only. Process and design
optimizations are recommended to develop an application-specific solution. With the proper PCB footprint and solder stencil
designs, the package will self-align during the solder reflow process.
• Stencil thickness is 100 or 125 μm.
• The PCB should be rated for the multiple lead-free reflow condition with a maximum 260 °C temperature.
• Use a standard pick-and-place process and equipment. Do not use a hand soldering process.
• Do not use a screw-down or stacking to mount the PCB into an enclosure. These methods could bend the PCB, which
would put stress on the package.
7.3
Halogen content
This package is designed to be halogen free, exceeding most industry and customer standards. Halogen free means that no
homogeneous material within the assembled package will contain chlorine (Cl) in excess of 700 ppm or 0.07% weight/weight or
bromine (Br) in excess of 900 ppm or 0.09% weight/weight.
MMA8452Q
48
Sensors
NXP Semiconductors
8
Package Information
The MMA8452Q device is housed in a 16-lead QFN package, case number 98ASA00063D.
8.1
Tape and reel information
MMA8452Q
Sensors
NXP Semiconductors
49
8.2
Package description
98ASA00063D, 16-pin QFN,
3 mm x 3 mm x 1.0 mm
MMA8452Q
50
Sensors
NXP Semiconductors
98ASA00063D, 16-pin QFN,
3 mm x 3 mm x 1.0 mm
MMA8452Q
Sensors
NXP Semiconductors
51
98ASA00063D, 16-pin QFN,
3 mm x 3 mm x 1.0 mm
MMA8452Q
52
Sensors
NXP Semiconductors
9
Revision History
Table 68. Revision history
Revision
number
Revision
date
Description of changes
10
04/2016
• The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP
Semiconductors.
• Legal texts have been adapted to the new company name where appropriate.
• Corrected Figure 6 title was MMA8451Q Mode Transition to MMA8452Q mode transition.
• Table 8: Updated header to include Q suffix on device numbers.
• Section 8.1: Deleted part marking information.
• Package outline updated to corporate format only, no technical changes.
9.2
06/2015
—
9.1
11/2014
—
9
07/2014
—
8.1
10/2013
—
8
07/2013
—
7
03/2013
—
6
02/2013
—
5
07/2012
—
MMA8452Q
Sensors
NXP Semiconductors
53
How to Reach Us:
Information in this document is provided solely to enable system and software implementers to use NXP products.
Home Page:
NXP.com
There are no expressed or implied copyright licenses granted hereunder to design or fabricate any integrated circuits
Web Support:
http://www.nxp.com/support
products herein.
based on the information in this document. NXP reserves the right to make changes without further notice to any
NXP makes no warranty, representation, or guarantee regarding the suitability of its products for any particular
purpose, nor does NXP assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation, consequential or incidental damages. "Typical"
parameters that may be provided in NXP data sheets and/or specifications can and do vary in different applications,
and actual performance may vary over time. All operating parameters, including "typicals," must be validated for each
customer application by the customer's technical experts. NXP does not convey any license under its patent rights nor
the rights of others. NXP sells products pursuant to standard terms and conditions of sale, which can be found at the
following address:
http://www.nxp.com/terms-of-use.html.
NXP, the NXP logo, Freescale, the Freescale logo, and the Energy Efficient Solutions logo are trademarks of NXP B.V.
All other product or service names are the property of their respective owners. All rights reserved.
© 2016 NXP B.V.
Document Number: MMA8452Q
Rev. 10
04/2016