Atmel Smart Energy Solution Guide Smart Energy Applications It’s all about energy management • Smart Grid • Industrial Lighting and Automation • Home Automation • Street Lighting • Solar Energy • PHEV Charging Stations The market for energy, water, and gas metering systems is rapidly changing, driven by new environmental and conservation concerns and regulations. Traditional standalone meters are now being replaced by complex networked systems that utilize a variety of communication methods. To meet the needs of this evolving smart grid, metering developers need solutions that can provide: • Leading-edge Connectivity • Best-in-class Metrology • Integration & Flexibility • Advanced Security 2 © 2015 / www.atmel.com Atmel Smart Energy Solutions Guide Atmel Smart Energy Solutions Not just a Chip, but a Platform Atmel® addresses the needs of the smart energy market with application-specific, as well as standard microcontroller, microprocessor, security, memory, wireless and power-line connectivity devices. The application-specific portfolio is defined from the ground up to offer designers best-in-class feature sets and performance in various classes of equipment used in the smart grid. Many of the devices in the Smart Energy Platform are part of the Atmel | SMART line of ARM®based microcontrollers. Home Area Network (HAN) IEEE 802.15.4, ZigBee, PRIME, G3-PLC WAN Neighborhood/Metro IEEE 802.15.4g, PRIME,G3-PLC HAN or Neighborhood IEEE 802.15.4(g), ZigBee Figure 1. Smart Grid Equipment and Governing Communications Standards Home Area Network Equipment Energy Gateway Data Concentrator Electricity Meter Gas & Water Meter M90E32/36 ü -- ü ü -- M90E26 -- -- -- ü -- ATSENSE -- -- ü ü -- PL230 ü -- -- ü -- PL250 ü -- -- ü -- RF212B ü ü -- ü ü RF233 ü ü -- ü ü RF215 -- ü ü ü -- RF215M -- ü ü ü ü SAM4C ü ü ü ü ü SAM4CM ü -- ü ü -- SAM4CP ü ü ü ü -- SAMD -- -- -- -- ü SAM4L ü -- -- ü ü SAMA5 -- ü ü -- -- Table 1. Atmel Platform Products by Equipment Type Atmel Smart Energy Solutions Guide 3 Atmel Smart Metering Platform Today’s smart meter architect demands various levels of integration depending on system architecture partitioning, project timelines, and the level of flexibility needed to address various utility and geographical requirements. The Atmel platform provides a unique multi-level architecture built around the same multi-core architecture as outlined below. Various devices integrate the building blocks of the smart meter, namely, metrology sensing (ADC), metrology DSP, application, communication, and security processing, as well as connectivity to home area and neighborhood area networks. Highest Integration and Flexibility Best-in-class Metrology Sensing Signal Processing Energy Measurement AFE 1ph/2ph/3ph Global Smart Meter Architectures M90Exx Leading-edge Connectivity Application Processor Protocol Processor PLC,RF Transceiver MCU MCU/MPU PRIME/G3 SAM4, SAMD SAM4, SAMA5 SAM9 ATPL230, ATPL250 Application & Communications Secure ASSP, Dual Cortex – M4, PRIME / G3 SAM4CP16 Analog Sensor 1ph/2ph/3ph ATSENSE Metrology & Application Secure ASSP Dual Core Cortex-M4 SAM4C4/8/16/32 Sensors & Metrology & Application Secure ASSP Dual Core Cortex-M4 1ph/3ph SAM4CMS4/8/16/32 SAM4CMP8/16/32 Sub-1GHz IEEE 802.15.4 AT86RF212B AT86RF215M 2.4GHz IEEE 802.15.4 AT86RF233 Dual-Band IEEE 802.15.4g AT86RF215 Figure 2. Atmel Smart Metering Platform 4 © 2015 / www.atmel.com Atmel Smart Energy Solutions Guide Atmel Value Proposition The broadest portfolio targeting at metering market. • Best-in-class Metrology • Standalone Sensing Analog Front End (AFE) and SOC with integrated AFE offering • Dynamic range of up to 6000:1 • 30M units shipped since 90’s • Leading-edge Connectivity • Low power IEEE 802.15.4 wireless devices • Field proven, Low power PLC (PRIME / G3) • Integration and Flexibility • Flexible (SW or HW) metrology • Multi-standard Wireless and PLC solutions • Advanced cryptography • Broad Atmel | SMART ARM-based Portfolio • Large array of SAMD, SAM4 and SAMA5 solutions • Best-in-class tools from Atmel, IAR, Keil Newest Smart Energy Platform Core: SAM4C The dual ARM Cortex-M4 architecture allows for integration of application layer, communications layers, and metrology functions in a single device. It has options for integrated software metrology or external hardware metrology AFE as well as integrated or external power-line carrier (PLC) physical layer solution. It’s a modular approach that is sure to meet various design needs. At the core of Atmel’s smart energy platform is the Atmel | SMART SAM4C series of products. The SAM4C4/8/16/32 system-on-chip solutions for smart energy applications are built around two highperformance 32-bit ARM Cortex®-M4 RISC processors. These devices operate at a maximum speed of 120 MHz and feature up to 2Mbyte of embedded Flash, 304 Kbytes of SRAM, and on-chip cache for each core. Temp Sensor M90Exx Metrology M90Exx AFE Metrology M90Exx AFE Metrology AFE Soft Metrology Options: Embedded Metrology ADC OR ATSENSE Metrology ADC LCD Driver (50x6) PIO(74-106) SRAM 24KB/48KB SRAM 128KB/256KB USART(5) UART(2) Cortex-M4F Cortex-M4 Metrology/Other App/Comm. Flash 256K-2MB USB (2MB ver. only) RF TRX Options Integrated PLC Options: External PLC Phy Options PRIME,G3 OR External ADC EBI(16bit) PWM(4) Timers (6) AES, CPKCC, ICM (SHA), TRNG SPI(6) TWI(2) RTC (<1uA) Figure 3. SAM4C Platform Atmel Smart Energy Solutions Guide 5 TDI System Peripherals Core Voltage Reg MPU DSP NVIC TICK WDT Unique ID Cortex-M4 (Core 0) XTAL 3-20 MHz LCD Voltage Reg ROM IAP & FFPI SAM-BA Boot Crypto Lib 4/8/12 MHz RC OSC TMS TCK Serial Wire and JTAG Debug Port AHB-AP LDO TD0 Flash 256KB 512KB 1MB 2MB (C32) AHB-AP 128K 256K(C32) FPU DSP NVIC TICK 16K(C32) SRAM1 16KB Cortex-M4 (Core 1) CPKCC SRAM0 SRAM2 8KB 32K(C32) ICM (SHA) Cache Cache 2 x PLL POR RTC Time Stamp RTT Async Bridge AHB Matrix (Mx0) PMC BOD Peripheral DMA AHB to APB Bridge 0 Tamper RC OSC 32KHz Supply Contr XTAL 32KHz PDC 10-bit ADC 6ch Backup domain PDC <74 GPIO 6-ch 16-bit Timer x5 USART <106 (C32E) PDC x1 UART PDC PDC x2 TWI AHB Matrix (Mx1) PDC 50 x 6 Segment LCD 6 SPI IPC0 TRNG, AES AHB to APB Bridge 1 Optional Metrology ADC 1/3ph F/S USB (C32E) PWM x1 UART Optical TRX IPC1 C32 devices have 2M flash, full speed USB, more GPIO, more RAM Figure 4. SAM4C Block Diagram SAM4CMP16/ SAM4CMP32/ SAM4C4 SAM4C8 SAM4C16 SAM4C32C SAM4C32E SAM4CMS4 SAM4CMP8/ SAM4CMS8 SAM4CMS16 SAM4CMS32 Flash SRAM 256KB 512KB 1MB 128 + 16 + 8KB 2MB 256KB 256 + 32 + 16KB 512KB 1MB 2MB 256 + 32 + 16KB 128 + 16 + 8KB Package 100 LQFP 144 LQFP 100 LQFP GPIO 74 106 52 / 57 PWM 4 3 UART+USART 7 5/6 SPI 2 Controllers - 8 CS, + 5 USARTs in SPI Mode 1 Controller - 4 CS + 3/4 USARTs in SPI Mode ADC 10bit, 6 x Externals + 2 x Internals 10bit, 4 x Externals + 2 x Internals Metrology AFE - 7 x Channels / 4 x Channels Segment LCD 50 x 6 33 x 6 / 38 x 6 USB FS - Host/ Device - Timer 6 Channels TWI 2 Table 2. SAM4C Metering SOC Feature Comparison 6 © 2015 / www.atmel.com Atmel Smart Energy Solutions Guide 0.5 0.4 Flexibility to support various country-specific requirements 0.3 0.2 Error Atmel’s software metrology library provides unprecedented level of performance, scalability, and flexibility which supports the integration of proprietary advanced metrology and signal processing algorithms. Atmel’s standard library enables residential, commercial, and industrial meter design up to class 0.2 accuracy, dynamic range of 3000:1, supports shunt, current transformer and Rogowski coil current sensing and is compliant with IEC 62052-11, 6205322/23, ANSI C12.1, C12.20 and MID. Active Energy % SAM4Cx Software Metrology 0.1 0 0.02 0.05 -0.1 0.1 0.2 0.5 1 2 5 10 20 50 100 A -0.2 -0.3 -0.4 -0.5 Obtained using PTC-8320 Tester, CT Ratio 2000:1, Burden Resistor 4.8Ohm 3P4W service type PF=1.0 PF=0.5L PF=0.8C Figure 5. SAM4CM Linear Curve The ATSENSE-301, ATSENSE-201 and ATSENSE-101 are AFE devices targeting metrology applications. They feature up to 7 channels of high-precision sigma-delta analog to digital converters (ADCs) with a 16ksps sample rate and a highly accurate, integrated voltage reference with 10 ppm/°C temperature stability. They also include programmable current signal amplification, a temperature sensor and a SPI (serial peripheral interface). ATSENSE Features • 0.1% accuracy over 3000:1 range • Shunt, CT and Rogowski coil support VDDA GNDA VP3 • 50ppm/°C reference,10ppm/°C (H version) VN • Works with Atmel Metrology library IP3 Σ∆ ADC PGA IN3 Σ∆ ADC Die Temperature Sensor • ATSENSE-301(H) • 32-pin TQFP package • 7 synchronous ∑−∆ ADCs, <16Ks/s • 3-V, 4-I channels with 8x PGA • ATSENSE-201(H) • 32-pin TQFP package • 4 synchronous ∑−∆ ADCs, <16Ks/s • 2-V, 2-I channels with 8x PGA • ATSENSE-101 • 20-pin SOIC package • 3 synchronous ∑−∆ ADCs, <16Ks/s • 1-V, 2-I channels with 8x PGA Atmel Smart Energy Solutions Guide Voltage Reference VTEMP Σ∆ ADC Decimator IP2 PGA IN2 Σ∆ ADC SPCK Serial Peripheral Interface Decimator NPCS MISO MOSI Control Registers VP1 Σ∆ ADC VN IP1 IN1 VREF 1K GNDREF VP2 VN VDDIN Decimator • Ultra-low-power: < 2.5mW/channel @ 3.3V • 8 MHz Serial Peripheral Interface (SPI) compatible mode 1(8-bit) for ADC data and AFE controls. 2.8V LDO Decimator PGA Σ∆ ADC Decimator Interrupt Controller Decimator OTP memory (Calibration Data) FS_CLK IP0 ADC_CLK IN0 DIFF MUX 2:1 PGA Σ∆ ADC Decimator ITOUT VDDIO Power Clock Generator On Reset GNDD MCLK VTEMP Figure 6. ATSENSE Block Diagram 7 Hardware Metrology AFE M90E26 M90E32AS M90E36A Out of the box solution for basic metering • Ideal for basic meter designs • Up to class 0.2 accuracy • Exceeds IEC, ANSI standards • Best-in-class temperature drift SAM4L Active Energy Error 0.3000 PF=1.0 • Great fit with SAM4L • picoPower® Technology • Active mode @ 90µA/MHz • Full RAM retention @1.5µA • SleepWalkingTM • 4x40 Segment LCD Controller • Hardware Crypto block PF=0.5L PF=0.8C 0.1000 Error • Best-in-class dynamic range (up to 6000:1) • Improves performance • Reduces OEM’s cost of manufacturing 0.2000 0.0000 -0.1000 -0.2000 -0.3000 0.01 0.02 0.05 0.10 0.20 0.50 1 2 5 10 20 40 50 60 80 Figure 7. M90E36A Linearity Service Type Dynamic Range Active Energy Accuracy Reactive Energy Accuracy Key Features - - - - Security SOC SAM4CMS4/8/16/32 1 phase 3000:1 0.1% 0.2% SAM4CMP8/16/32 3 phase 3000:1 0.1% 0.2% ATSENSE101 1 phase 3000:1 1% 1% ATSENSE201 2 phase 3000:1 0.2% 0.2% ATSENSE301 3 phase 3000:1 0.2% 0.2% M90E26 1 phase 5000:1 0.1% 0.2% AFE, active, reactive energy, instantaneous and anti-tamper M90E32AS 3 phase 6000:1 0.1% 0.2% AFE, active, reactive energy, instantaneous, fundamental & harmonics measurement, piece-wise compensation, event detection 0.2% AFE, active, reactive energy, instantaneous, fundamental & harmonics measurement, Discrete Fourier Transform (DFT) Function, raw data capture SAMC4/8/16/32 M90E36A 3 phase 100 Current (A) 6000:1 0.1% High End Metrology SOC Software Metrology ADC Table 3. Atmel Metrology Solutions 8 © 2015 / www.atmel.com Atmel Smart Energy Solutions Guide PLC Connectivity Products Atmel offers PLC solutions designed specifically for narrowband communications using the low-voltage electric grid. Drawing on our deep expertise in PLC modem technology and extensive collaboration with utilities and metering OEMs, we’ve created solutions offering an unprecedented level of integration and performance. Our solutions support various standards such as PRIME (PoweRline Intelligent Metering Evolution) and G3-PLC. Thanks to the communications software provided by our solution, the management of PLC networks turns into a transparent process. Users can focus on top-level applications and access the Atmel PLC software stack via user-friendly application programming interfaces (APIs). • Best-in-class sensitivity and high-temperature stability • Improved AFE providing outstanding efficiency • Price-competitive, high-performance solutions • Free software stacks for PLC Flexible Architecture Atmel PLC solutions are offered in single chip (SOC) and two-chip (PHY modem + MCU) configuration, respectively. Both configurations are available for PRIME and G3 solutions. Atmel PRIME devices comply with state-of-the-art specification and include enhanced PRIME features such as additional robust modes and frequency band extension up to 500 KHz. Atmel G3 devices support all modulation schemes and modes (coherent, differential) defined in the G3-PLC specification. Single Chip ASSP Two Chip MCU + PHY COSEM Application Process IEC 62056-6-1/6-2 COSEM Application Layer IEC 62056-5-3 SSCS WRAPPER IEC-62056-47 IEC-61334-4-32 MCU UDP IPv6 SAM4CPx MAC Layer PRIME (ITU-T G.9904) DATA LINK Layer G3 PHY Layer PRIME PHY Layer G3 (ITU-T G.9904) Line Driver (ITU-T G.9903) ATPL2x PHY (ITU-T G.9903) DC/DC Supply DC/DC Supply Line Driver AC/DC Supply Coupling PHY MEDIA Coupling MV AC/DC Supply LV Figure 8. Atmel PLC Solutions. Flexible Architecture Atmel Smart Energy Solutions Guide 9 A built in class-D amplifier architecture is up to 30% more efficient than competing solutions with only a handful of external discrete components, reducing power waste due to heat dissipation and increasing long-term reliability due to better thermal behavior. An extensive array of system I/O, LCD, memory, RTC, DMA and cryptographic resources available in the Atmel | SMART SAM4CP series allow integration of application, communication and metrology software (using external Atmel metrology devices) to achieve highly reliable, flexible and cost effective smart meter designs. Standard Frequency Band Core CPU Clock Flash SRAM Package PL230A PRIME CEN / ARIB / FCC -- -- -- -- LQFP 80 PL250A G3 CEN / ARIB / FCC -- -- -- -- LQFP 80 SAM4CP16B PRIME CEN / ARIB / FCC 120 MHz @core 1 MB 128 +16 + 8 KB LQFP 176 SAM4CP16C G3 CEN / ARIB / FCC Dual Cortex-M4 Dual Cortex-M4 120 MHz @core 1 MB 128 +16 + 8 KB LQFP 176 Table 4. PLC Product Features TDI System Peripherals Core Voltage Reg TMS TCK Serial Wire and JTAG Debug Port AHB-AP LDO TDO AHB-AP SRAM2 8KB MPU DSP FPU DSP NVIC TICK NVIC TICK WDT LCD Voltage Reg Unique ID Cortex-M4 (Core 0) XTAL 3-20 MHz Flash 4/8/12 MHz RC OSC CPKCC 1MB ROM IAP & FFPI SAM-BA Boot Crypto Lib SRAM1 16KB Cortex-M4 (Core 1) SRAM0 128KB ICM (SHA) Cache Cache 2 x PLL POR RTC Time Stamp RTT Tamper RC OSC 32kHz Supply Contr XTAL 32kHz Backup domain Async Bridge AHB Matrix (Mx0) PMC BOD Peripheral DMA AHB to APB Bridge 0 PDC 10-bit ADC 6ch PDC 6-ch 16-bit Timer Up to 67 I/Os x5 USART PDC x1 UART PDC x2 TWI PDC 46 x 5 Segment LCD AHB Matrix (Mx1) TRNG, AES IPC0 PLC Modem (PRIME or G3) AHB to APB Bridge 1 PDC x1 SPI PWM x1 UART Optical TRX IPC1 Figure 9. SAM4CP Series Block Diagram 10 © 2015 / www.atmel.com Atmel Smart Energy Solutions Guide Atmel PLC Software Stacks DLMS / Application Layer USER APPLICATION UDP Layer Convergence Layer Service Specific Convergence Sublayer (SSCS) IPv4 IPv6 IEC-432 NULL IPv6 Layer Management Plane New SSCS Adaptation Layer Common Part Convergence Sublayer (CPCS) MAC Layer MAC Layer MLME-SAP MAC Layer Mgmt. Entity(MLME) PHY Layer PLME-SAP PHY Layer Mgmt. Entity(PLME) TxResult Figure 10. Atmel PRIME Software Stack PHY API Rx PHY Layer Figure 11. Atmel G3 Software Stack Atmel provides PRIME and G3 software stacks that turn the management of PLC networks into a transparent process. Users can focus on top-level applications and access the Atmel PLC software stacks via user-friendly application programming interfaces (APIs). Atmel Smart Energy Solutions Guide 11 Wireless Connectivity Products Key Products Efficient smart energy wireless applications require both high-performance and power efficiency. Atmel transceivers deliver the leading RF link budget with the industry’s lowest power consumption. The AT86RF212B is a low-power, low-voltage RF transceiver for the regional 700/800/900 MHz frequency bands available in Japan, China, Europe and North America. This transceiver offers an extremely good 120 dB link budget (-110 dBm receiver sensitivity / +10 dBm transmit power) designed for low-cost IEEE 802.15.4, ZigBee® and high data rate ISM applications. Additionally, Atmel offers the most feature-rich IEEE 802.15.4-compliant transceiver family available. Our transceivers support regional sub-1 GHz bands, as well as the global 2.4 GHz band. This enables you to develop wireless applications for customers worldwide, including emerging markets like China. The Atmel AT86RF233 transceiver is designed to operate in the 2.4 GHz ISM band, available worldwide. This transceiver offers link budgets up to 105 dB (-101 dBm receiver sensitivity/+4 dBm transmit power). For a complete overview of features, key parameters, and targeted application areas, please see the data sheet. Enhanced Performance Powerful hardware features like antenna diversity or external power amplifier support let you further boost transceiver performance to maximize network reliability and RF range of your system. Atmel transceivers support not only IEEE 802.15.4-compliant applications, but provide on-air data rates up to 2 Mbit/s for general purpose ISM (industrial scientific medical) applications. Pin compatibility ensures an easy transition between devices or frequency bands. AT86RF215 is a dual-band sub-1 GHz/2.4 GHz transceiver compliant to IEEE 802.15.4-2011, IEEE 802.15.4g-2012 and ETSI TS 102 887-1. The device offers very high flexibility by supporting a variety of data rates with three modulation schemes: multi-rate and multi-regional frequency shift keying (MR-FSK), orthogonal frequency division multiplexing (MR-OFDM), as well as offset quadrature phase-shift keying (MR-OQPSK). This includes the physical layer which is used for ZigBee PRO and IP. With an output power of 14 dBm and receiver sensitivities down to -123 dBm, link budgets up to 137 dB can be achieved. To help you speed up system development and prototyping, Atmel offers a variety of free software suites, various hardware evaluation boards, and development kits and modules. VDD CB2 CX1 CX2 XTAL 31 30 29 28 27 26 25 AVSS AVSS AVDD EVDD AVSS XTAL1 XTAL2 2 DIG4 5 RFN AT86RF233 DVSS 21 MISO 29 DVSS DVSS 18 DEVDD 7 DVSS DVDD SCLK 19 DVDD 6 AVSS DVSS C2 AT86RF212B SLP_TR B1 MOSI 22 4 RFP DIG2 F1 3 AVSS DIG1 C1 RF IRQ 24 /SEL 23 9 10 11 12 13 14 15 16 8 /RST CLKM 17 C3 VDD CB3 CB4 AVR / ARM Controller R1 Digital Interface 1 DIG3 32 AVSS CB1 Figure 12. Wireless Tranceiver Application Diagram 12 © 2015 / www.atmel.com Atmel Smart Energy Solutions Guide 2.4 GHz Radio Baseband Core RX RX Frame Buffer MR-FSK RF MR-OFDM TX TX Frame Buffer MR-O-QPSK AT86RF215 Sub-1 GHz Radio RX Digital Control and Data SPI LVDS Interface I/Q Data Baseband Core RX Frame Buffer MR-FSK MR-OFDM RF TX TX Frame Buffer MR-O-QPSK Figure 13. RF215 Block Diagram Device AT86RF212B Transceiver AT86RF233 Transceiver AT86RF215 Transceiver and I/Q radio Band [MHz] 769 ... 935 2322 ... 2527 389 …510 779 …1020 RX Sens. [dBm] Max.TX Power [dBm] 20, 40, 100, 250 -110 10 proprietary: 200, 400, 500, 1000 @ 20 kbit/s 250 -101 Modulation Data Rate [kbit/s] BPSK, O-QPSK O-QPSK proprietary: 500, 1000, 2000 @ 250 kbit/s MR-FSK, MR-OFDM, MR-O-QPSK, O-QPSK 6.25 … 800 -123 proprietary up to 2400 @ 6.25 kbit/s MR-FSK, MR-OFDM, MR-O-QPSK, O-QPSK 6.25 … 800 -123 proprietary up to 2400 @ 6.25 kbit/s Current: SLEEP, TRX_OFF, RX_ON, BUSY_TX 0.2 µA 0.4 mA 9.2 mA Pack. Compliance QFN32 IEEE 802.15.4-2006, IEEE 802.15.4-2011 QFN32 IEEE 802.15.4-2006, IEEE 802.15.4-2011 QFN48 IEEE 802.15.4-2006, IEEE 802.15.4-2011, IEEE 802.15.4g-2012, ETSI TS 102 887-1 QFN48 IEEE 802.15.4-2011, IEEE 802.15.4g-2012, ETSI TS 102 887-1 17.0 mA @ 5 dBm 4 0.02/0.2 µA 0.3 mA 6.0/11.8 mA 13.8 mA @ 4 dBm 14 30 nA 3.0 mA 28 mA 65 mA @ 14 dBm 2400 …2483 AT86RF215M Transceiver and I/Q radio 389 …510 779 …102 14 30 nA 3.0 mA 28 mA 65 mA @ 14 dBm Table 5. Wireless Transceiver Products Atmel Smart Energy Solutions Guide 13 Smart Energy Portfolio Product ATSAM4C4C ATSAM4C8C Metering MCU ATSAM4C16C ATSAM4C32CA ATSAM4C32EA ATSAM4CMS4C ATSAM4CMS8C 1 Phase ATSAM4CMS16C Metrology SoC ATSAM4CMS32C ATSAM4CMP8C 3 Phase ATSAM4CMP16C ATSAM4CMP32C 14 Ordering Code Package Features Flash MRL ATSAM4C4CB-AU 100LQFP Green, IND TEMP, CRYPTO 256 KB B ATSAM4C4CB-AUR 100LQFP Green, IND TEMP, CRYPTO 256 KB B ATSAM4C8CA-AU 100LQFP Green, IND TEMP, CRYPTO 512 KB A ATSAM4C8CA-AUR 100LQFP Green, IND TEMP, CRYPTO 512 KB A ATSAM4C8CB-AU 100LQFP Green, IND TEMP, CRYPTO 512 KB B ATSAM4C8CB-AUR 100LQFP Green, IND TEMP, CRYPTO 512 KB B ATSAM4C16CA-AU 100LQFP Green, IND TEMP, CRYPTO 1 MB A ATSAM4C16CA-AUR 100LQFP Green, IND TEMP, CRYPTO 1 MB A ATSAM4C16CB-AU 100LQFP Green, IND TEMP, CRYPTO 1 MB B ATSAM4C16CB-AUR 100LQFP Green, IND TEMP, CRYPTO 1 MB B ATSAM4C32CA-AU 100LQFP Green, IND TEMP, CRYPTO 2 MB A ATSAM4C32CA-AUR 100LQFP Green, IND TEMP, CRYPTO 2 MB A ATSAM4C32EA-AU 144LQFP Green, IND TEMP, CRYPTO 2 MB A ATSAM4C32EA-AUR 144LQFP Green, IND TEMP, CRYPTO 2 MB A ATSAM4CMS4CB-AU 100LQFP Green, IND TEMP, CRYPTO 256 KB ATSAM4CMS4CB-AUR 100LQFP Green, IND TEMP, CRYPTO 256 KB ATSAM4CMS8CA-AU 100LQFP Green, IND TEMP, CRYPTO 512 KB A ATSAM4CMS8CA-AUR 100LQFP Green, IND TEMP, CRYPTO 512 KB A ATSAM4CMS8CB-AU 100LQFP Green, IND TEMP, CRYPTO 512 KB B ATSAM4CMS8CB-AUR 100LQFP Green, IND TEMP, CRYPTO 512 KB B ATSAM4CMS16CA-AU 100LQFP Green, IND TEMP, CRYPTO 1 MB A ATSAM4CMS16CA-AUR 100LQFP Green, IND TEMP, CRYPTO 1 MB A ATSAM4CMS16CB-AU 100LQFP Green, IND TEMP, CRYPTO 1 MB B ATSAM4CMS16CB-AUR 100LQFP Green, IND TEMP, CRYPTO 1 MB B ATSAM4CMS32CA-AU 100LQFP Green, IND TEMP, CRYPTO 2 MB A ATSAM4CMS32CA-AUR 100LQFP Green, IND TEMP, CRYPTO 2 MB A ATSAM4CMP8CA-AU 100LQFP Green, IND TEMP, CRYPTO 512 KB A ATSAM4CMP8CA-AUR 100LQFP Green, IND TEMP, CRYPTO 512 KB A ATSAM4CMP8CB-AU 100LQFP Green, IND TEMP, CRYPTO 512 KB B ATSAM4CMP8CB-AUR 100LQFP Green, IND TEMP, CRYPTO 512 KB B ATSAM4CMP16CA-AU 100LQFP Green, IND TEMP, CRYPTO 1 MB A ATSAM4CMP16CA-AUR 100LQFP Green, IND TEMP, CRYPTO 1 MB A ATSAM4CMP16CB-AU 100LQFP Green, IND TEMP, CRYPTO 1 MB B ATSAM4CMP16CB-AUR 100LQFP Green, IND TEMP, CRYPTO 1 MB B ATSAM4CMP32CA-AU 100LQFP Green, IND TEMP, CRYPTO 2 MB A ATSAM4CMP32CA-AUR 100LQFP Green, IND TEMP, CRYPTO 2 MB A © 2015 / www.atmel.com Atmel Smart Energy Solutions Guide Carrier Part Numbers Kit Contents Pictures IDE RTOS STACKS/LIBRARIES ATMEL Studio & ASF IAR KEIL FreeRTOS ATMEL Metrology & Crypto Libraries ATMEL Studio & ASF IAR KEIL FreeRTOS ATMEL Metrology & Crypto Libraries Tray Tape & Reel Tray Tape & Reel Tray ATSAM4C-EK Tape & Reel Tray Tape & Reel Tools Tray Tape & Reel Tray Tape & Reel ATSAM4C32-EK Tray Tape & Reel Tray Tape & Reel Tray Tape & Reel Tray Tape & Reel ATSAM4CMS-DB Tray Tape & Reel Tray Tape & Reel Tray Tape & Reel Tools Tray Tape & Reel Tray Tape & Reel Tray Tape & Reel ATSAM4CMP-DB Tray Tape & Reel Tray Tape & Reel Atmel Smart Energy Solutions Guide 15 Smart Energy Portfolio (Continued) Product PRIME Modem PRIME SoC Ordering Code Package Features Flash MRL ATPL230A-AKU-Y 80LQPF Green, IND TEMP -- A ATPL230A-AKU-R 80LQPF Green, IND TEMP -- A ATSAM4CP16B-AHU-Y 176LQFP Green, IND TEMP 1 MB A ATPL250A-AKU-Y 80LQPF Green, IND TEMP -- -- ATPL250A-AKU-R 80LQPF Green, IND TEMP -- -- ATSAM4CP16C-AHU-Y 176LQFP Green, IND TEMP 1 MB -- AT86RF212B-ZU 32QFN 700/800/900 MHz Transceiver, 85˚C -- -- AT86RF212B-ZUR 32QFN 700/800/900 MHz Transceiver, 85˚C -- -- AT86RF233-ZF 32QFN 2.4 GHz Transceiver, 125˚C -- -- AT86RF233-ZFR 32QFN 2.4 GHz Transceiver, 125˚C -- -- AT86RF233-ZU 32QFN 2.4 GHz Transceiver, 85˚C -- -- AT86RF233-ZUR 32QFN 2.4 GHz Transceiver, 85˚C -- -- AT86RF215-ZU 48QFN Dual-Band Transceiver, 85°C -- -- AT86RF215-ZUR 48QFN Dual-Band Transceiver, 85°C -- -- AT86RF215M-ZU 48QFN Sub-1 GHz Transceiver, 85°C -- -- AT86RF215M-ZUR 48QFN Sub-1 GHz Transceiver, 85°C -- -- AT86RF215IQ-ZU 48QFN Dual-Band I/Q Radio, 85°C -- -- AT86RF215IQ-ZUR 48QFN Dual-Band I/Q Radio, 85°C -- -- ATPL230A ATSAM4CP16B PLC G3 Modem G3 SoC Sub-1 GHz Transceiver (IEEE 802.15.4-2011) 2.4 GHz Transceiver (IEEE 802.15.4-2006) RF ATSAM4CP16C AT86RF212B AT86RF233 Dual-Band Transceiver (IEEE 802.15.4g-2012) AT86RF215 Sub-1 GHz Transceiver (IEEE 802.15.4g-2012) AT86RF215M Dual-Band I/Q Radio 16 ATPL250A AT86RF215IQ © 2015 / www.atmel.com Atmel Smart Energy Solutions Guide Carrier Part Numbers Tray ATPL230A-EK (2 Modem Boards + 4 Couplings) Tape & Reel ATSAM4CP16B-EK (2 Boards + 4 Couplings) Tray Tools Tray ATPL250A-EK (2 Modem Boards + 4 Couplings) Tape & Reel ATSAM4CP16C-EK (2 Boards + 4 Couplings) Tray Kit Contents Pictures 2x 2x 2x 2x 2x 2x 2x 2x IDE RTOS STACKS/LIBRARIES ATMEL Studio & ASF IAR FreeRTOS PRIME ATMEL Studio & ASF IAR FreeRTOS PRIME ATMEL Studio & ASF IAR FreeRTOS G3 ATMEL Studio & ASF IAR FreeRTOS G3 2x 2x 2x 2x Tray ATSAM4L-XPRO + ATZB212B-XPRO Tape & Reel Tray ATSAM4L-XPRO/ ATSAM4S-XPRO + ATREB233-XPRO or ATZB-A-233-XPRO (Amplified) Tape & Reel Tray Tape & Reel Tray Tape & Reel Tray Tools ATMEL Studio ASF Wireless Performance Analyzer Exegin Technologies: FreeRTOS eCOS (SAM9) IEEE 802.15.4 MAC, ZigBee Pro/SEP1.x, ZigBee IP/SEP2.0, 6LoWPAN n/a n/a ATSAM4L-XPRO/ ATSAM4S-XPRO + ATREB215-XPRO Tape & Reel Tray ATREB215-XPRO n/a Tape & Reel Atmel Smart Energy Solutions Guide 17 Smart Energy Portfolio (Continued) Product 1 Phase 2 Phase ATSENSE100 ATSENSE200 SAM4C AFE Companion Chip 3 Phase 1 Phase ATSENSE300 Ordering Code Package Features Flash MRL ATSENSE101A-SU 20SOIC GREEN, IND TEMP -- A ATSENSE101A-SUR 20SOIC GREEN, IND TEMP -- A ATSENSE201A-AU 32LQFP GREEN, IND TEMP -- A ATSENSE201A-AUR 32LQFP GREEN, IND TEMP -- A ATSENSE201HA-AU 32LQFP GREEN, IND TEMP -- A ATSENSE201HA-AUR 32LQFP GREEN, IND TEMP -- A ATSENSE301A-AU 32LQFP GREEN, IND TEMP -- A ATSENSE301A-AUR 32LQFP GREEN, IND TEMP -- A ATSENSE301HA-AU 32LQFP GREEN, IND TEMP -- A ATSENSE301HA-AUR 32LQFP GREEN, IND TEMP -- A ATM90E26-YU-B 28-SSOP IND TEMP, 1.8V/3V -- -- ATM90E26-YU-R 28-SSOP IND TEMP, 1.8V/3V -- -- ATM90E32AS-AU-R 48-TQFP IND TEMP, 1.8V/3V -- -- ATM90E32AS-AU-Y 48-TQFP IND TEMP, 1.8V/3V -- -- ATM90E36A-AU-R 48-TQFP IND TEMP, 1.8V/3V -- -- ATM90E36A-AU-Y 48-TQFP IND TEMP, 1.8V/3V -- -- ATM90E26 ATM90E32 Stand Alone AFE (90E series) 3 Phase ATM90E36 18 © 2015 / www.atmel.com Atmel Smart Energy Solutions Guide Carrier Part Numbers Kit Contents Pictures IDE RTOS STACKS/LIBRARIES Tube Tape & Reel Tube Tape & Reel Tube Tape & Reel Tools Use Metrology SoC Tools Tube Tape & Reel Tube Tape & Reel Tube ATM90E2X-DB All SAM4C Software tools + Metrology Libraries ATM90E32AS-DB All SAM4C Software tools + Metrology Libraries ATM90E32AS-RD Atmel Cortex-M4 based SAM4LC4C microcontroller and ATM90E32A Atmel Poly-Phase Energy Metering AFE chipset Tape & Reel Tape & Reel Tray Tools Tape & Reel ATM90E36A-DB All SAM4C Software tools + Metrology Libraries Tray ATM90E36A-RD Atmel Cortex-M4 based SAM4LC4C microcontroller and ATM90E36A Atmel Poly-Phase Energy Metering AFE chipset Atmel Smart Energy Solutions Guide 19 Atmel Corporation 1600 Technology Drive, San Jose, CA 95110 USA T: (+1)(408) 441.0311 F: (+1)(408) 436.4200 | www.atmel.com © 2015 Atmel Corporation. / Rev.: Atmel-45055I-Smart-Energy-Solution-Guide_E_US_102015 Atmel,® Atmel logo and combinations thereof, Enabling Unlimited Possibilities,® and others are registered trademarks or trademarks of Atmel Corporation in U. S. and other countries. Other terms and product names may be trademarks of others. Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.