Download

Datasheet
W S I F u s e Te r m i n a l s w i t h L o w
C u r re n t S t a t u s I n d i c a t i o n
Weidmuller offers versions of the WSI fuse terminals
with low current blown fuse indication (BFI).
The BFI circuit is located in parallel with the fuse so
that a current goes through the indicator only when
the fuse blows. As this current is an unwanted off-state
leakage current it is important that the level be kept to
an absolute minimum. Weidmuller’s BFI circuits draw
no more than 500µA - not enough to pose a safety
hazard or falsely energize PLC or DCS digital inputs.
Features:
• WSI 6 LD for 5x20mm fuses, just 8mm wide
• WSI 6/2 LD for 1¼" x ¼" fuses, 12mm wide
• Moulded from UL 94-V0 Wemid material
• 35mm DIN rail mounting
• Non-polarized, full wave rectified LED circuit with less
than 500µA leakage at nominal voltage as per CSA
Standard C22.2 No. 39 Fuse Holder Assemblies and
UL Standard 512 Fuseholders.
Canada
Mexico
United States
Weidmuller, Canada
10 Spy Court
Markham, Ontario L3R 5H6
Telephone: (800) 268-4080
Facsimile: (905) 475-2798
Email: [email protected]
Website: www.weidmuller.ca
Weidmuller, Mexico
Blvd. Hermanos Serdán 698
Col. San Rafael Oriente
Puebla, Puebla, Mexico
C.P. 72029
Telephone: 01 222 2686267
Facsimile: 01 222 2686219
Email: [email protected]
Website: www.weidmuller.com.mx
Weidmuller
821 Southlake Blvd.
Richmond, Virginia 23236
Telephone: (800) 849-9343
Facsimile: (804) 379-2593
Email: [email protected]
Website: www.weidmuller.com
WSI Fuse Terminals with Low Current Status Indication
WSI 6 LD and WSI 6/2 LD
WSI 6 LD
WSI 6/2
with LED indicator for
DC or AC voltage
with LED for inch fuses VAC/VDC
Note:
Voltage is disconnected by opening the disconnect lever. If the
fuse of the LED variants is defective, the downstream circuit is still
under current, since low-level current is still flowing via the LED.
W
W
Technical data
Dimensions/approvals
ar
ar
Width/length/height (mm)
with TS 35 x 7.5
Insulation stripping length/clamping screw/screwdriver blade
Rated data of terminal base (for Europe)
Rated voltage/current/cross-section
Rated impulse voltage acc. to VDE 0110/1.89 /pollution severity
Further technical data
Tightening torque range
Nm
Torque setting with DMS 2 electric screwdriver
8/60/72
12mm/M 3.5/4.0 x 0.8
12/60/79.5
12mm/M 3.5/4.0 x 0.8
500 V/6.3 A /6mm2
6 kV/3
500 V/6.3 A /6mm2
6 kV/3
0.8…1.6
3
0.8…1.6
3
mm2
mm2
mm2
mm2
mm2
Size
A
A
0.5…10
1.5…10
0.5…10
0.5…6
0.5…6
0.5…10
26
26
0.5…10
1.5…10
0.5…10
0.5…6
0.5…6
0.5…10
26
26
UL
CSA
300 V/10 A/20…8 AWG
300 V/10 A/20…8 AWG
Clampable conductors
Solid H07V-U
Stranded H07V-R
Flexible H07V-K
Flexible H07V-K and ferrule acc. to DIN 46 228/1
Flexible H07V-K and ferrules with plastic insul. collar
Max. clamping range in mm2/Gauge pin acc. to 947-1
Cont. current of cross-connect. 2-pole
Cont. current of cross-connect. multi-pole
UL/CSA rated data
Voltage/current/conductor size
Voltage/current/conductor size
A5
A5
600 V/16 A/20…8 AWG
600 V/16 A/20…8 AWG
Ordering data
Description
10-36VAC/DC, 0.5mA typ.
30-70VAC/DC, 0.5mA typ.
60-150VAC/DC, 0.5mA typ.
250VAC/110VDC, 0.5mA typ.
Partition/End plate
WAP
Thickness 1.5mm
Version
Dark beige Wemid/LED
Dark beige Wemid/LED
Dark beige Wemid/LED
Dark beige Wemid/LED
WTW
Type
WSI 6/LD 10-36VAC/DC LL
WSI 6/LD 30-70VAC/DC LL
WSI 6/LD 60-150VAC/DC LL
WSI 6/LD 250VAC/110VDC LL
Type
Qty.
50
50
50
50
Qty.
Part No.
1011300001
1012200001
1012300001
1012400001
Part No.
Type
WSI 6/2/LD 10-36VAC/DC LL
WSI 6/2/LD 30-70VAC/DC LL
WSI 6/2/LD 60-150VAC/DC LL
WSI 6/2/LD 250VAC/110VDC LL
Type
Qty.
25
25
25
25
Qty.
Part No.
1014100001
1014200001
1014300001
1014400001
Part No.
WAP
WTW 2.5-10
50
20
1050000000
1050100000
WAP
WTW 2.5-10
50
20
1050000000
1050100000
QL 2
QL 3
QL 4
QL 10
BS-M 3x5
PS 2.3
WAW 2
5 x 20mm
50
50
50
20
100
20
1
0194300000
0194400000
0194500000
0338300000
1052100000
0180400000
9004510000
50
50
50
20
100
20
1
0470700000
0470800000
0470900000
0471000000
1052100000
0180400000
9004510000
10
10
10
10
10
10
10
10
10
10
10
10
0430300000
0430400000
0430500000
0430600000
0430700000
0430800000
0430900000
0431000000
0431100000
0431200000
0431300000
0431400000
QL 2
QL 3
QL 4
QL 10
BS-M 3x5
PS 2.3
WAW 2
¼" x 1¼"
E2A
E3A
E5A
E7A
E 10 A
10
10
10
10
10
029450000
029570000
029460000
029580000
209390000
Thickness 1.5mm
Cross-connection/Test plug/Notching tool
QL 2–10
Notching tool for QL WAW 2
Fuse inserts
0.10A
0.20A
0.25A
0.50A
1.0A
1.6A
2.0A
2.5A
3.15A
4.0A
5.0A
6.3A
Mounting rails, brackets, additional marking material and accessories please see relevant Catalog Section
2
Subject to technical changes • 5/09-LIT0914