8-Channel, 12-Bit, Configurable ADC/DAC with On-Chip Reference, I2C Interface AD5593R Data Sheet FEATURES GENERAL DESCRIPTION 8-channel, configurable ADC/DAC/GPIO Configurable as any combination of 8 12-bit DAC channels 8 12-bit ADC channels 8 general-purpose I/O pins Integrated temperature sensor 16-lead TSSOP and LFCSP and 16-ball WLCSP packages I2C interface The AD5593R has eight input/output (I/O) pins, which can be independently configured as digital-to-analog converter (DAC) outputs, analog-to-digital converter (ADC) inputs, digital outputs, or digital inputs. When an I/O pin is configured as an analog output, it is driven by a 12-bit DAC. The output range of the DAC is 0 V to VREF or 0 V to 2 × VREF. When an I/O pin is configured as an analog input, it is connected to a 12-bit ADC via an analog multiplexer. The input range of the ADC is 0 V to VREF or 0 V to 2 × VREF. The I/O pins can also be configured to be general-purpose, digital input or output (GPIO) pins. The state of the GPIO pins can be set or read back by accessing the GPIO write data register and GPIO read configuration registers, respectively, via an I2C write or read operation. APPLICATIONS Control and monitoring General-purpose analog and digital I/O The AD5593R has an integrated 2.5 V, 20 ppm/°C reference that is turned off by default and an integrated temperature indicator that gives an indication of the die temperature. The temperature value is read back as part of an ADC read sequence. The AD5593R is available in 16-lead TSSOP and LFCSP, as well as a 16-ball WLCSP, and operates over a temperature range of −40°C to +105°C. Table 1. Related Products Product AD5592R AD5592R-1 Description AD5593R equivalent with SPI interface AD5593R equivalent with SPI interface and VLOGIC pin FUNCTIONAL BLOCK DIAGRAM VLOGIC VDD VREF AD5593R 2.5V REFERENCE POWER-ON RESET GPIO0 INPUT REGISTER DAC REGISTER DAC 0 INPUT REGISTER DAC REGISTER DAC 7 I/O0 SCL SDA A0 RESET I 2C INTERFACE LOGIC GPIO7 I/O7 MUX SEQUENCER 12-BIT SUCCESSIVE APPROXIMATION ADC T/H GND 12507-001 TEMPERATURE INDICATOR Figure 1. Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2014–2016 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD5593R Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Serial Interface ................................................................................ 21 Applications ....................................................................................... 1 Write Operation.......................................................................... 21 General Description ......................................................................... 1 Read Operation........................................................................... 21 Functional Block Diagram .............................................................. 1 Pointer Byte ................................................................................. 23 Revision History ............................................................................... 2 Control Registers ........................................................................ 23 Specifications..................................................................................... 3 General-Purpose Control Register .......................................... 24 Timing Characteristics ................................................................ 6 Configuring the AD5593R ........................................................ 25 Absolute Maximum Ratings............................................................ 7 DAC Write Operation................................................................ 26 Thermal Resistance ...................................................................... 7 DAC Readback............................................................................ 26 ESD Caution .................................................................................. 7 ADC Operation .......................................................................... 27 Pin Configuration and Function Descriptions ............................. 8 GPIO Operation ......................................................................... 29 Typical Performance Characteristics ........................................... 11 Power-Down/Reference Control .............................................. 30 Terminology .................................................................................... 16 Reset Function ............................................................................ 30 Theory of Operation ...................................................................... 18 Applications Information .............................................................. 31 DAC Section ................................................................................ 18 Microprocessor Interfacing ....................................................... 31 ADC Section ............................................................................... 18 AD5593R to ADSP-BF537 Interface........................................ 31 GPIO Section .............................................................................. 20 Layout Guidelines....................................................................... 31 Internal Reference ...................................................................... 20 Outline Dimensions ....................................................................... 32 Reset Function ............................................................................ 20 Ordering Guide............................................................................... 33 Temperature Indicator ............................................................... 20 REVISION HISTORY 1/16—Rev. A to Rev. B Added 16-Lead LFCSP....................................................... Universal Added VLOGIC Parameter and ILOGIC Parameter, Table 2 ............... 5 Added Figure 4 and Table 7; Renumbered Sequentially ............. 9 Added Calculating ADC Input Current Section and Figure 33 .... 20 Changes to Temperature Indicator Section................................. 21 Changes to Figure 34 ...................................................................... 22 Changes to Figure 35 and Figure 36 ............................................. 23 Changes to Figure 37 ...................................................................... 24 Change to DAC Readback Section ............................................... 27 Changes to ADC Operation Section ............................................ 28 Changes to Outline Dimensions................................................... 33 Changes to Ordering Guide .......................................................... 34 10/14—Rev. 0 to Rev. A Added 16-Ball WLCSP ...................................................... Universal Changes to Gain Error Parameter, Table 1 .....................................3 Changes to Table 5.............................................................................7 Added Figure 4 and Table 7; Renumbered Sequentially ..............9 Change to ADC Section ................................................................ 17 Changes to Reset Function Section and Temperature Indicator Section ............................................................................ 19 Changes to Reset Function Section, Table 24, and Table 25 .......... 27 Added Figure 41, Outline Dimensions ........................................ 29 Updated Outline Dimensions ....................................................... 29 Changes to Ordering Guide .......................................................... 29 8/14—Revision 0: Initial Version Rev. B | Page 2 of 33 Data Sheet AD5593R SPECIFICATIONS VDD = 2.7 V to 5.5 V, VREF = 2.5 V (internal), TA = TMIN to TMAX, unless otherwise noted. Table 2. Parameter ADC PERFORMANCE Resolution Input Range1 Integral Nonlinearity (INL) Differential Nonlinearity (DNL) Offset Error Gain Error Track Time (tTRACK)2 Conversion Time (tCONV)2 Signal to Noise Ratio (SNR)3 Min 69 67 61 69 67 60 −91 −89 −72 91 91 72 15 12 50 −95 8.2 1.6 dB dB dB dB dB dB dB dB ns ns ps dB MHz MHz 2 Spurious Free Dynamic Range (SFDR) Aperture Delay2 Aperture Jitter2 Channel-to-Channel Isolation Full Power Bandwidth 12 0 0 −1 −1 −3 VREF 2 × VREF +1 +1 +3 8 Zero Code Error Total Unadjusted Error (TUE) 0.65 ±0.03 ±0.015 Capacitive Load Stability Resistive Load Short-Circuit Current DC Crosstalk2 DC Output Impedance DC Power Supply Rejection Ratio (PSRR)2 Load Impedance at Rails5 Unit Bits V V LSB LSB mV % FSR ns μs dB dB dB dB VREF 2 × VREF +2 +1 ±5 0.3 500 Total Harmonic Distortion (THD) INL DNL Offset Error Offset Error Drift2 Gain Error Max 12 0 0 −2 −1 Signal-to-Noise + Distortion (SINAD) Ratio DAC PERFORMANCE4 Resolution Output Range Typ ±0.2 ±0.1 2 ±0.25 ±0.1 2 10 1 25 −4 +4 0.2 0.15 25 Bits V V LSB LSB mV μV/°C % FSR % FSR mV % FSR % FSR nF nF kΩ mA μV Ω mV/V Ω Rev. B | Page 3 of 33 Test Conditions/Comments fIN = 10 kHz sine wave ADC range select bit = 0 ADC range select bit = 1 VDD = 2.7 V, input range = 0 V to VREF VDD = 5.5 V, input range = 0 V to VREF VDD = 5.5 V, input range = 0 V to 2 × VREF VDD = 2.7 V, input range = 0 V to VREF VDD = 3.3 V, input range = 0 V to VREF VDD = 5.5 V, input range = 0 V to 2 × VREF VDD = 2.7 V, input range = 0 V to VREF VDD = 3.3 V, input range = 0 V to VREF VDD = 5.5 V, input range = 0 V to 2 × VREF VDD = 2.7 V, input range = 0 V to VREF VDD = 3.3 V, input range = 0 V to VREF VDD = 5.5 V, input range = 0 V to 2 × VREF VDD = 3 V VDD = 5 V fIN = 5 kHz At 3 dB At 0.1 dB DAC range select bit = 0 DAC range select bit = 1 Output range = 0 V to VREF Output range = 0 V to 2 × VREF Output range = 0 V to VREF Output range = 0 V to 2 × VREF RLOAD = ∞ RLOAD = 1 kΩ Single channel, full-scale output change DAC code = midscale, VDD = 3 V ± 10% or 5 V ± 10% AD5593R Parameter Load Regulation Data Sheet Min Power-Up Time AC SPECIFICATIONS Slew Rate Settling Time DAC Glitch Impulse DAC to DAC Crosstalk Digital Crosstalk Analog Crosstalk Digital Feedthrough Multiplying Bandwidth Output Voltage Noise Spectral Density SNR SFDR SINAD Total Harmonic Distortion REFERENCE INPUT VREF Input Voltage DC Leakage Current VREF Input Impedance REFERENCE OUTPUT VREF Output Voltage VREF Temperature Coefficient Capacitive Load Stability Output Impedance Max μV/mA 7 μs 1.25 6 2 1 0.1 1 0.1 240 200 V/μs μs nV-sec nV-sec nV-sec nV-sec nV-sec kHz nV/√Hz 81 77 74 −76 dB dB dB dB Test Conditions/Comments VDD = 5 V ± 10%, DAC code = midscale, −10 mA ≤ IOUT ≤ +10 mA VDD = 3 V ± 10%, DAC code = midscale, −10 mA ≤ IOUT ≤ +10 mA Exiting power-down mode, VDD = 5 V DAC code = full scale, output range = 0 V to 2 × VREF DAC code = midscale, output range = 0 V to 2 × VREF, measured at 10 kHz VDD +1 V μA kΩ kΩ No I/Ox pins configured as DACs DAC output range = 0 V to 2 × VREF DAC output range = 0 V to VREF 2.505 V ppm/°C μF Ω Ω μV p-p nV/√Hz μV/V μV/V RLOAD = 2 kΩ VDD = 2.7 V VDD = 5 V 0.1 Hz to 10 Hz At ambient, f = 1 kHz, CL = 10 nF At ambient, sweeping VDD from 2.7 V to 5.5 V At ambient, sweeping VDD from 2.7 V to 3.3 V 210 120 ±5 μV/mA μV/mA mA At ambient, −5 mA ≤ load current ≤ +5 mA At ambient, −5 mA ≤ load current ≤ +5 mA VDD ≥ 3 V 1.6 mA 12 24 2.495 Unit μV/mA 200 1 −1 Output Voltage Noise Density Line Regulation Load Regulation Sourcing Sinking Output Current Load Capability GPIO OUTPUT ISOURCE and ISINK Output Voltage High, VOH Low, VOL GPIO INPUT Input Voltage High, VIH Low, VIL Input Capacitance Hysteresis Input Current Typ 200 2.5 20 5 0.15 0.7 10 240 20 10 VDD − 0.2 0.4 VDD × 0.7 VDD × 0.3 20 0.2 ±1 V V V V pF V μA Rev. B | Page 4 of 33 ISOURCE = 1 mA ISOURCE = 1 mA Data Sheet Parameter LOGIC INPUTS Input Voltage High, VINH Low, VINL Input Current, IIN Input Capacitance, CIN LOGIC OUTPUT (SDA) Output High Voltage, VOH Output Low Voltage, VOL Floating-State Output Capacitance TEMPERATURE SENSOR2 Resolution Operating Range Accuracy Track Time POWER REQUIREMENTS VDD IDD Power-Down Mode Normal Mode VDD = 5 V AD5593R Min Max Unit +0.01 0.3 × VLOGIC +1 10 V V μA pF 0.7 × VLOGIC −1 VLOGIC − 0.2 0.4 10 12 −40 +105 ±3 5 20 2.7 VDD = 3 V VLOGIC ILOGIC Typ 1.8 5.5 2.7 3.5 V V pF Bits °C °C μs μs ISOURCE = 200 μA; VDD = 2.7 V to 5.5 V ISINK = 200 μA ADC buffer enabled ADC buffer disabled V Digital inputs = 0 V or VDD μA 1.6 1 2.4 mA mA mA 1.1 mA 1 0.75 0.5 0.5 1.1 1 1.1 mA mA mA mA mA mA mA 0.78 mA 0.75 0.5 0.45 0.45 mA mA mA mA V μA VDD 3.5 Test Conditions/Comments 1 I/O0 to I/O7 are DACs, internal reference, gain = 2 I/O0 to I/O7 are DACs, external reference, gain = 2 I/O0 to I/O7 are DACs and sampled by the ADC, internal reference, gain = 2 I/O0 to I/O7 are DACs and sampled by the ADC, external reference, gain = 2 I/O0 to I/O7 are ADCs, internal reference, gain = 2 I/O0 to I/O7 are ADCs, external reference, gain = 2 I/O0 to I/O7 are general-purpose outputs I/O0 to I/O7 are general-purpose inputs I/O0 to I/O7 are DACs, internal reference, gain = 1 I/O0 to I/O7 are DACs, external reference, gain = 1 I/O0 to I/O7 are DACs and sampled by the ADC, internal reference, gain = 1 I/O0 to I/O7 are DACs and sampled by the ADC, external reference, gain = 1 I/O0 to I/O7 are ADCs, internal reference, gain = 1 I/O0 to I/O7 are ADCs, external reference, gain = 1 I/O0 to I/O7 are general-purpose outputs I/O0 to I/O7 are general-purpose inputs When using the internal ADC buffer, there is a dead band of 0 V to 5 mV. Guaranteed by design and characterization; not production tested. All specifications expressed in decibels are referred to full-scale input, FSR, and tested with an input signal at 0.5 dB below full scale, unless otherwise specified. 4 DC specifications tested with the outputs unloaded, unless otherwise noted. Linearity calculated using a reduced code range of 8 to 4085. An upper dead band of 10 mV exists when VREF = VDD. 5 When drawing a load current at either rail, the output voltage headroom with respect to that rail is limited by the 25 Ω typical channel resistance of the output devices. For example, when sinking 1 mA, the minimum output voltage = 25 Ω × 1 mA = 25 mV (see Figure 26 and Figure 27). 2 3 Rev. B | Page 5 of 33 AD5593R Data Sheet TIMING CHARACTERISTICS All input signals are specified with tR = tF = 1 ns/V (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2; VDD = 2.7 V to 5.5 V, 1.8 V ≤ VLOGIC ≤ VDD; 2.5 V ≤ VREF ≤ VDD; all specifications TMIN to TMAX, unless otherwise noted. Table 3. Parameter1 t1 t2 t3 t4 t5 t62 t7 t8 t9 t10 Min 2.5 0.6 1.3 0.6 100 Typ Max Unit μs μs μs μs ns μs μs μs μs ns ns ns ns ns ns pF 0.9 0.6 0.6 1.3 300 0 t11 250 0 300 20 + 0.1CB3 CB 3 400 Conditions/Comments SCL cycle time tHIGH, SCL high time tLOW, SCL low time tHD,STA, start/repeated start condition hold time tSU,DAT, data setup time tHD,DAT, data hold time tSU,STA, setup time for repeated start tSU,STO, stop condition setup time tBUF, bus free time between a stop and a start condition tR, rise time of SCL and SDA when receiving tR, rise time of SCL and SDA when receiving (CMOS compatible) tF, fall time of SDA when transmitting tF, fall time of SDA when receiving (CMOS compatible) tF, fall time of SCL and SDA when receiving tF, fall time of SCL and SDA when transmitting Capacitive load for each bus line 1 Guaranteed by design and characterization; not production tested. A master device must provide a hold time of at least 300 ns for the SDA signal (referred to the VIH min of the SCL signal) to bridge the undefined region of the falling edge of SCL. 3 CB is the total capacitance of one bus line in pF. tR and tF are measured between 0.3 VDD and 0.7 VDD. 2 Timing Diagram SDA t9 t3 t11 t10 t4 t4 t6 t2 t5 START CONDITION t1 t7 REPEATED START CONDITION Figure 2. 2-Wire Serial Interface Timing Diagram Rev. B | Page 6 of 33 t8 STOP CONDITION 12507-002 SCL Data Sheet AD5593R ABSOLUTE MAXIMUM RATINGS TA = 25°C, unless otherwise noted. Transient currents of up to 100 mA do not cause SCR latch-up. Table 4. Parameter VDD to GND VLOGIC to GND Analog Input Voltage to GND Digital Input Voltage to GND Digital Output Voltage to GND VREF to GND Operating Temperature Range Storage Temperature Range Junction Temperature (TJ max) Lead Temperature Soldering Rating −0.3 V to +7 V −0.3 V to +7 V −0.3 V to VDD + 0.3 V −0.3 V to VLOGIC + 0.3 V −0.3 V to VLOGIC +0.3 V −0.3 V to VDD +0.3 V −40°C to +105°C −65°C to +150°C +150°C JEDEC industry-standard J-STD-020 THERMAL RESISTANCE θJA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 5. Thermal Resistance Package Type 16-Lead TSSOP 16-Lead LFCSP 16-ball WLCSP ESD CAUTION Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Rev. B | Page 7 of 33 θJA 112 137 60 Unit °C/W °C/W °C/W AD5593R Data Sheet RESET 1 16 SCL A0 2 15 SDA 14 GND 13 I/O7 12 I/O6 VDD 3 I/O0 4 I/O1 5 AD5593R TOP VIEW (Not to Scale) 6 11 I/O5 I/O3 7 10 I/O4 VREF 8 9 VLOGIC I/O2 12507-003 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 3. 16-Lead TSSOP Pin Configuration Table 6. 16-Lead TSSOP Pin Function Descriptions Pin No. 1 Mnemonic RESET 2 3 4 to 7, 10 to 13 A0 VDD I/O0 to I/O7 8 VREF 9 14 15 VLOGIC GND SDA 16 SCL Description Asynchronous Reset Pin. Tie this pin high for normal operation. When this pin is brought low, the AD5593R is reset to its default configuration. Address Input. Sets the LSB of the 7-bit slave address. Power Supply Input. The AD5593R can operate from 2.7 V to 5.5 V. Decouple the supply with a 0.1 μF capacitor to GND. Input/Output 0 Through Input/Output 7. These pins can be independently configured as DACs, ADCs, or generalpurpose digital inputs or outputs. The function of each pin is determined by programming the appropriate bits in the configuration registers. Reference Input/Output. When the internal reference is enabled, the 2.5 V reference voltage is available on the VREF pin. A 0.1 μF capacitor connected from the VREF pin to GND is recommended to achieve the specified performance from the AD5593R. When the internal reference is disabled, an external reference must be applied to this pin. The voltage range for the external reference is 1 V to VDD. Interface Power Supply. The voltage on this pin ranges from 1.8 V to 5.5 V. Ground Reference Point for All Circuitry. Serial Data Input. This pin is used in conjunction with the SCL line to clock data in to or out of the input shift register. SDA is a bidirectional, open-drain line that must be pulled to the VLOGIC supply with an external pull-up resistor. Serial Clock Line. This pin is used in conjunction with the SDA line to clock data in to or out of the 16-bit input register. Rev. B | Page 8 of 33 13 SDA 14 SCL 16 A0 AD5593R 15 RESET Data Sheet V DD 1 12 GND I/O0 2 AD5593R 11 I/O7 I/O1 3 TOP VIEW (Not to Scale) 10 I/O6 I/O4 8 VLOGIC 7 I/O3 5 VREF 6 I/O5 12507-004 9 I/O2 4 Figure 4. 16-Lead LFCSP Pin Configuration Table 7. 16-Ball LFCSP Pin Function Descriptions Pin No. 1 2 to 5, 8 to 11 Mnemonic VDD I/O0 to I/O7 6 VREF 7 12 13 VLOGIC GND SDA 14 SCL 15 RESET 16 A0 Description Power Supply Input. The AD5593R operates from 2.7 V to 5.5 V. Decouple the supply with a 0.1 μF capacitor to GND. Input/Output 0 through Input/Output 7. These pins can be independently configured as DACs, ADCs, or generalpurpose digital inputs or outputs. The function of each pin is determined by programming the appropriate bits in the configuration registers. Reference Input/Output. When the internal reference is enabled, the 2.5 V reference voltage is available on the pin. A 0.1 μF capacitor connected from the VREF pin to GND is recommended to achieve the specified performance from the AD5593R. When the internal reference is disabled, an external reference must be applied to this pin. The voltage range for the external reference is 1 V to VDD. Interface Power Supply. The voltage ranges from 1.8 V to 5.5 V. Ground Reference Point for All Circuitry. Serial Data Input. This pin is used in conjunction with the SCL line to clock data into or out of the input shift register. SDA is a bidirectional, open-drain line that must be pulled to the VLOGIC supply with an external pull-up resistor. Serial Clock Line. This is pin used in conjunction with the SDA line to clock data into or out of the 16-bit input register. Asynchronous Reset Pin. Tie this pin high for normal operation. When this pin is brought low, the AD5593R is reset to its default configuration. Address Input. This pin sets the LSB of the 7-bit slave address. Rev. B | Page 9 of 33 AD5593R Data Sheet BALL A1 INDICATOR 1 2 3 4 SDA SCL RESET A0 GND I/O7 I/O0 VDD I/O6 I/O3 I/O2 I/O1 I/O4 VLOGIC VREF I/O5 A B D TOP VIEW (BALL SIDE DOWN) Not to Scale 12507-201 C Figure 5. 16-Ball WLCSP Pin Configuration Table 8. 16-Ball WLCSP Pin Function Descriptions Pin No. A3 Mnemonic RESET A4 B4 B3, C4, C3, C2, D1, D4, C1, B2 D3 A0 VDD I/O0 to I/O7 D2 B1 A1 VLOGIC GND SDA A2 SCL VREF Description Asynchronous Reset Pin. Tie this pin high for normal operation. When this pin is brought low, the AD5593R is reset to its default configuration. Address Input. Sets the LSB of the 7-bit slave address. Power Supply Input. The AD5593R can operate from 2.7 V to 5.5 V. Decouple the supply with a 0.1 μF capacitor to GND. Input/Output 0 through Input/Output 7. These pins can be independently configured as DACs, ADCs, or generalpurpose digital inputs or outputs. The function of each pin is determined by programming the appropriate bits in the configuration registers. Reference Input/Output. When the internal reference is enabled, the 2.5 V reference voltage is available on the pin. A 0.1 μF capacitor connected from the VREF pin to GND is recommended to achieve the specified performance from the AD5593R. When the internal reference is disabled, an external reference must be applied to this pin. The voltage range for the external reference is 1 V to VDD. Interface Power Supply. The voltage ranges from 1.8 V to 5.5 V. Ground Reference Point for All Circuitry. Serial Data Input. This pin is used in conjunction with the SCL line to clock data into or out of the input shift register. SDA is a bidirectional, open-drain line that must be pulled to the VLOGIC supply with an external pull-up resistor. Serial Clock Line. This is used in conjunction with the SDA line to clock data into or out of the 16-bit input register. Rev. B | Page 10 of 33 Data Sheet AD5593R TYPICAL PERFORMANCE CHARACTERISTICS 1.0 0.5 0.4 0.8 0.3 0.2 DNL (LSB) INL (LSB) 0.6 0.4 0.2 0.1 0 –0.1 –0.2 –0.3 0 0 1000 2000 3000 4000 ADC CODE –0.5 12507-102 –0.2 0 1000 3000 4000 Figure 9. ADC DNL; VDD = 2.7 V Figure 6. ADC INL; VDD = 5.5 V 35000 0.5 0.4 30000 NUMBER OF OCCURRENCES 0.3 0.2 DNL (LSB) 2000 ADC CODE 12507-105 –0.4 0.1 0 –0.1 –0.2 –0.3 25000 VDD = 2.7V SAMPLES = 60000 VIN = 1.5V GAIN = 1 EXTERNAL REFERENCE = 2.5V 20000 15000 10000 5000 0 1000 2000 3000 4000 ADC CODE 0 12507-103 –0.5 2529 2530 ADC CODE Figure 10. Histogram of ADC Codes; VDD = 2.7 V Figure 7. ADC DNL; VDD = 5.5 V 35000 0.5 0.4 30000 NUMBER OF OCCURRENCES 0.3 0.2 0.1 0 –0.1 –0.2 –0.3 25000 VDD = 5.5V SAMPLES = 60000 VIN = 1.5V GAIN = 1 EXTERNAL REFERENCE = 2.5V 20000 15000 10000 5000 –0.5 0 1000 2000 3000 ADC CODE 4000 0 2520 2521 2522 2523 2524 2525 ADC CODE Figure 11. Histogram of Codes; VDD = 5.5 V Figure 8. ADC INL; VDD = 2.7 V Rev. B | Page 11 of 33 2526 12507-101 –0.4 12507-104 INL (LSB) 2528 12507-100 –0.4 AD5593R Data Sheet 1 4 VDD = 3V/5V 2 –1 GLITCH (nV-sec) ADC BANDWIDTH (dB) 0 –2 –3 –4 0 –2 10k 100k 1M 10M 100M FREQUENCY (Hz) –4 12507-124 –6 1k 0 0.5 2.505 VOUT (V) 4095 0 2.500 1024 2048 3072 4095 DAC CODE 2.490 –10 12507-130 0 0 10 20 TIME (µs) Figure 13. DAC INL 12507-115 2.495 Figure 16. DAC Digital to Analog Glitch (Rising) 2.510 0.5 2.505 VOUT (V) 1.0 0 –0.5 2.500 0 1024 2048 DAC CODE 3072 4095 12507-127 2.495 Figure 14. DAC DNL 2.490 –10 0 10 TIME (µs) Figure 17. DAC Digital to Analog Glitch (Falling) Rev. B | Page 12 of 33 20 12507-116 INL (LSB) 2.510 –0.5 DNL (LSB) 3072 Figure 15. DAC Adjacent Code Glitch 1.0 –1.0 2048 DAC CODE Figure 12. ADC Bandwidth –1.0 1024 12507-126 –5 Data Sheet AD5593R 2.58 4.0 2.56 3.5 RL = 2kΩ CL = 200pF 2.54 3.0 VOUT (V) VOUT (V) 2.52 2.50 2.48 2.5 2.0 2.46 0 5 10 0 2 3 4 5 Figure 21. DAC Settling Time, Output Range = 0 V to 2 × VREF 2.58 4.0 2.56 3.5 2.54 3.0 2.52 2.5 VOUT (V) Figure 18. DAC Settling Time (100 Code Change, Rising Edge) 2.50 2.0 2.48 1.5 2.46 1.0 2.44 0.5 2.42 –10 –5 0 5 10 TIME (µs) 0nF LOAD 10nF LOAD 22nF LOAD 47nF LOAD 0 –5 0 5 10 15 TIME (µs) Figure 19. DAC Settling Time (100 Code Change, Falling Edge) Figure 22. DAC Settling Time vs. Capacitive Load 2.00 200 150 1.75 RL = 2kΩ CL = 200pF 100 VOUT (µV p-p) 1.50 1.25 1.00 50 0 –50 –100 0.75 0 1 2 3 4 TIME (µs) 5 Figure 20. DAC Settling Time, Output Range = 0 V to VREF –200 0 2 4 6 8 TIME (Seconds) Figure 23. DAC 1/f Noise with External Reference Rev. B | Page 13 of 33 10 12507-109 0.50 –150 12507-131 VOUT (V) 1 TIME (µs) 12507-120 VOUT (V) TIME (µs) 1.0 12507-121 –5 12507-119 2.42 –10 12507-132 1.5 2.44 AD5593R Data Sheet 5 200 150 4 OUTPUT VOLTAGE (V) VOUT (µV p-p) 100 50 0 –50 –100 3 FULL-SCALE 2 3/4 SCALE 1/2 SCALE 1 1/4 SCALE –150 2 4 6 8 10 TIME (Seconds) 0 –30 10 20 30 6 FULL-SCALE OUTPUT VOLTAGE (V) 5 1500 1000 3/4 SCALE 4 3 1/2 SCALE 2 1/4 SCALE 1 ZERO SCALE 500 0 10 100 1k 10k 100k FREQUENCY (Hz) 1M Figure 25. DAC Output Noise Spectral Density –1 –30 –20 –10 0 10 20 LOAD CURRENT (mA) Figure 27. DAC Output Sink and Source Capability, Output Range = 0 V to 2 × VREF Rev. B | Page 14 of 33 30 12507-134 0 12507-112 NSD (nV/√Hz) 0 Figure 26. DAC Output Sink and Source Capability, Output Range = 0 V to VREF FULL-SCALE 3/4 SCALE MID-SCALE 1/4 SCALE ZERO SCALE 2000 –10 LOAD CURRENT (mA) Figure 24. DAC 1/f Noise with Internal Reference 2500 ZERO SCALE –20 12507-133 0 12507-110 –200 Data Sheet AD5593R 20 2.5005 15 2.5003 5 VREF (V) VOUT (µV p-p) 10 0 –5 2.5001 2.4999 –10 2.4997 0 2 4 6 8 10 TIME (Seconds) Figure 28. Internal Reference 1/f Noise 1000 600 400 200 1k 10k 100k FREQUENCY (Hz) 1M 12507-113 NSD (nV/√Hz) 800 100 3.0 3.3 3.6 3.9 4.2 4.5 4.8 VDD (V) Figure 30. Reference Line Regulation 1200 0 10 2.4995 2.7 Figure 29. Reference Noise Spectral Density Rev. B | Page 15 of 33 5.1 5.4 12507-200 –20 12507-111 –15 AD5593R Data Sheet TERMINOLOGY ADC Integral Nonlinearity (INL) For the ADC, INL is the maximum deviation from a straight line passing through the endpoints of the ADC transfer function. The end points of the transfer function are zero scale, a point that is 1 LSB below the first code transition, and full scale, a point that is 1 LSB above the last code transition. ADC Total Harmonic Distortion (THD) THD is the ratio of the rms sum of harmonics to the fundamental. For the AD5593R, it is defined as ADC Differential Nonlinearity (DNL) For the ADC, DNL is the difference between the measured and the ideal 1 LSB change between any two adjacent codes in the ADC. where V1 is the rms amplitude of the fundamental and V2, V3, V4, V5, and V6 are the rms amplitudes of the second through the sixth harmonics. Offset Error Offset error is the deviation of the first code transition (00 … 000) to (00 … 001) from the ideal, that is, AGND + 1 LSB. Peak Harmonic or Spurious Noise Peak harmonic or spurious noise is defined as the ratio of the rms value of the next largest component in the ADC output spectrum (up to fS/2 and excluding dc) to the rms value of the fundamental. Normally, the value of this specification is determined by the largest harmonic in the spectrum, but for ADCs where the harmonics are buried in the noise floor, it is a noise peak. Gain Error Gain error is the deviation of the last code transition (111 … 110) to (111 … 111) from the ideal (that is, VREF − 1 LSB) after the offset error has been adjusted out. Channel-to-Channel Isolation Channel-to-channel isolation is a measure of the level of crosstalk between channels. It is measured by applying a fullscale 5 kHz sine wave signal to all nonselected ADC input channels and determining how much that signal is attenuated in the selected channel. This specification is the worst case across all ADC channels for the AD5593R. ADC Power Supply Rejection Ratio (PSRR) For the ADC, variations in power supply affect the full-scale transition, but not the converter linearity. Power supply rejection is the maximum change in the full-scale transition point due to a change in power supply voltage from the nominal value. Track-and-Hold Acquisition Time The track-and-hold amplifier goes into track mode when the ADC sequence register has been written to. The track and hold amplifier goes into hold mode when the conversion starts (see Figure 37). Track-and-hold acquisition time is the minimum time required for the track-and-hold amplifier to remain in track mode for its output to reach and settle to within ±1 LSB of the applied input signal, given a step change to the input signal. Signal-to-(Noise + Distortion) Ratio (SINAD) SINAD is the measured ratio of signal to (noise + distortion) at the output of the analog-to-digital converter. The signal is the rms amplitude of the fundamental. Noise is the sum of all nonfundamental signals up to half the sampling frequency (fS/2), excluding dc. The ratio is dependent on the number of quantization levels in the digitization process; the more levels, the smaller the quantization noise. The theoretical SINAD for an ideal N-bit converter with a sine wave input is given by Signal-to-(Noise + Distortion) (dB) = 6.02N + 1.76 Thus, for a 12-bit converter, this is 74 dB. THD dB 20 log V 2 V3 V4 V5 V6 2 2 2 2 2 V1 DAC Relative Accuracy or Integral Nonlinearity (INL) For the DAC, relative accuracy or integral nonlinearity is a measurement of the maximum deviation, in LSBs, from a straight line passing through the endpoints of the DAC transfer function. A typical INL vs. code plot is shown in Figure 13. DAC Differential Nonlinearity (DNL) For the DAC, differential nonlinearity is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of ±1 LSB maximum ensures monotonicity. This DAC is guaranteed monotonic by design. A typical DNL vs. code plot can be seen in Figure 14. Zero Code Error Zero code error is a measurement of the output error when zero code (0x000) is loaded to the DAC register. Ideally, the output is 0 V. The zero code error is always positive in the AD5593R because the output of the DAC cannot go below 0 V due to a combination of the offset errors in the DAC and the output amplifier. Zero code error is expressed in mV. Gain Error Gain error is a measure of the span error of the DAC. It is the deviation in slope of the DAC transfer characteristic from the ideal expressed as % of FSR. Offset Error Offset error is a measure of the difference between VOUT (actual) and VOUT (ideal) expressed in mV in the linear region of the transfer function. Offset error can be negative or positive. Offset Error Drift Offset error drift is a measurement of the change in offset error with a change in temperature. It is expressed in μV/°C. Rev. B | Page 16 of 33 Data Sheet AD5593R DAC DC Power Supply Rejection Ratio (PSRR) For the DAC, PSRR indicates how the output of the DAC is affected by changes in the supply voltage. PSRR is the ratio of the change in VOUT to a change in VDD for full-scale output of the DAC. It is measured in mV/V. VREF is held at 2 V, and VDD is varied by ±10%. Output Voltage Settling Time Output voltage settling time is the amount of time it takes for the output of a DAC to settle to a specified level for a ¼ to ¾ full-scale input change and is measured from the rising edge of SDA that generates the stop condition. Digital-to-Analog Glitch Impulse Digital-to-analog glitch impulse is the impulse injected into the analog output when the input code in the DAC register changes state. It is normally specified as the area of the glitch in nV-sec, and is measured when the digital input code is changed by 1 LSB at the major carry transition (0x7FF to 0x800) (see Figure 16 and Figure 17). Digital Feedthrough Digital feedthrough is a measure of the impulse injected into the analog output of the DAC from the digital inputs of the DAC, but is measured when the DAC output is not updated. It is specified in nV-sec, and measured with a full-scale code change on the data bus, that is, from all 0s to all 1s and vice versa. Analog Crosstalk Analog crosstalk is the glitch impulse transferred to the output of one DAC due to a change in the output of another DAC. It is first measured by loading one of the input registers with a fullscale code change (all 0s to all 1s and vice versa). Then it is measured by executing a software LDAC and monitoring the output of the DAC whose digital code was not changed. The area of the glitch is expressed in nV-sec. DAC-to-DAC Crosstalk DAC-to-DAC crosstalk is the glitch impulse transferred to the output of one DAC due to a digital code change and subsequent analog output change of another DAC. It is measured by loading the attack channel with a full-scale code change (all 0s to all 1s and vice versa), using the write to and update commands while monitoring the output of the victim channel that is at midscale. The energy of the glitch is expressed in nV-sec. Multiplying Bandwidth The amplifiers within the DAC have a finite bandwidth. The multiplying bandwidth is a measure of this finite bandwidth. A sine wave on the reference (with full-scale code loaded to the DAC) appears on the output. The multiplying bandwidth is the frequency at which the output amplitude falls to 3 dB below the input. Reference Feedthrough Reference feedthrough is the ratio of the amplitude of the signal at the DAC output to the reference input when the DAC output is not being updated. It is expressed in dB. DAC Total Harmonic Distortion (THD) For the DAC, THD is the difference between an ideal sine wave and its attenuated version using the DAC. The sine wave is used as the reference for the DAC, and the THD is a measurement of the harmonics present on the DAC output. It is measured in dB. Noise Spectral Density (NSD) NSD is a measurement of the internally generated random noise. Random noise is characterized as a spectral density (nV/√Hz). It is measured by loading the DAC to midscale and measuring noise at the output. It is measured in nV/√Hz. A plot of noise spectral density is shown in Figure 25. Voltage Reference Temperature Coefficient (TC) Voltage reference TC is a measure of the change in the reference output voltage with a change in temperature. The voltage reference TC is calculated using the box method, which defines the TC as the maximum change in the reference output over a given temperature range expressed in ppm/°C, as follows: DC Crosstalk DC crosstalk is the dc change in the output level of one DAC in response to a change in the output of another DAC. It is measured with a full-scale output change on one DAC (or soft power-down and power-up) while monitoring another DAC kept at midscale. It is expressed in μV. DC crosstalk due to load current change is a measure of the impact that a change in load current on one DAC has to another DAC kept at midscale. It is expressed in μV/mA. Digital Crosstalk Digital crosstalk is the glitch impulse transferred to the output of one DAC at midscale in response to a full-scale code change (all 0s to all 1s and vice versa) in the input register of another DAC. It is measured in standalone mode and is expressed in nV-sec. VREF(MAX) VREF(MIN) 10 6 TC VREF(NOM) Temp Range where: VREF(MAX) is the maximum reference output measured over the total temperature range. VREF(MIN) is the minimum reference output measured over the total temperature range. VREF(NOM) is the nominal reference output voltage, 2.5 V. Temp Range is the specified temperature range of −40°C to +105°C. Rev. B | Page 17 of 33 AD5593R Data Sheet THEORY OF OPERATION The AD5593R is an 8-channel, configurable analog and digital I/O port. The AD5593R has eight pins that can be independently configured as a 12-bit DAC output channel, a 12-bit ADC input channel, a digital input pin, or a digital output pin. R R The function of each pin is determined by programming the ADC, DAC, or GPIO configuration registers as appropriate. R DAC SECTION TO OUTPUT AMPLIFIER The AD5593R contains eight 12-bit DACs. Each DAC consists of a string of resistors followed by an output buffer amplifier. Figure 31 shows a block diagram of the DAC architecture. R VREF REF (+) OUTPUT AMPLIFIER GND 12507-012 REF (–) R I/Ox 12507-011 DAC REGISTER RESISTOR STRING Figure 32. Resistor String DAC Output Buffer Figure 31. DAC Channel Architecture Block Diagram The DAC channels share a single DAC range bit (see Bit D4 in Table 13) that sets the output range to 0 V to VREF or 0 V to 2 × VREF. Because the range bit is shared by all channels, it is not possible to set different output ranges on a per channel basis. The input coding to the DAC is straight binary. Therefore, the ideal output voltage is given by D VOUT G VREF N 2 where: G = 1 for an output range of 0 V to VREF or G = 2 for an output range of 0 V to 2 × VREF. VREF is the voltage on the VREF pin. D is the decimal equivalent of the binary code (0 to 4095) that is loaded to the DAC register. N = 12. Resistor String The simplified segmented resistor string DAC structure is shown in Figure 32. The code loaded to the DAC register determines the switch on the string that is connected to the output buffer. Because each resistance in the string has the same value, R, the string DAC is guaranteed monotonic. The output buffer is designed as an input/output rail-to-rail buffer. The output buffer can drive 2 nF capacitance with a 1 kΩ resistor in parallel. The slew rate is 1.25 V/μs with a ¼ to ¾ scale settling time of 6 μs. By default, the DAC outputs update directly after data has been written to the input register. The LDAC register delays the updates until additional channels have been written to if required. See the LDAC Mode Operation section for more information. ADC SECTION The ADC section is a fast, 12-bit, single-supply ADC with a conversion time of 2 μs. The ADC is preceded by a multiplexer that switches selected I/O pins to the ADC. A sequencer is included to switch the multiplexer to the next selected channel automatically. Channels are selected for conversion by writing to the ADC sequence register. When the write to the ADC sequence register has completed, the first channel in the conversion sequence is put into track mode. Each channel can track the input signal for a minimum of 500 ns. The conversion is initiated on the rising edge of the clock for the acknowledge (ACK) that occurs after the slave address (see Figure 37). Each conversion takes 2 μs. The ADC has a range bit (ADC range select in the general-purpose control register, see Bit D5 in Table 13) that sets the input range as 0 V to VREF or 0 V to 2 × VREF. All input channels share the same range. The output coding of the ADC is straight binary. It is possible to set each I/Ox pin as both a DAC and an ADC. In this case, the primary function is that of the DAC. If the pin is selected for inclusion in an ADC conversion sequence, the voltage on the pin is converted and made available via the serial interface. This allows the DAC voltage to be monitored. Rev. B | Page 18 of 33 Data Sheet AD5593R Calculating ADC Input Current Calculate the input current for buffered mode as follows: The current flowing into the I/Ox pins configured as ADC inputs varies with sampling rate (fS), the voltage difference between successive channels (VDIFF), and whether buffered or unbuffered mode is used. Figure 33 shows a simplified version of the ADC input structure. When a new channel is selected for conversion, 5.8 pF must be charged to or discharged from the voltage that on the previously selected channel. The time required for the charge or discharge depends on the voltage difference between the two channels. This dependence affects the input impedance of the multiplexer and, therefore, the input current flowing into the I/Ox pins. fS × C × VDIFF + 1 nA where: fS is the ADC sample rate in Hz. C is the sampling capacitance in farads. VDIFF is the voltage change between successive channels. Calculate the input current for buffered mode as follows: fS × C × VDIFF where 1 nA is the dc leakage current associated with unbuffered mode. The input current for the ADC in buffered mode, where I/O0 = 0.5 V, I/O1 = 2 V, and fS = 10 kHz, is as follows: In buffered mode, Switch S1 is open and Switch S2 is closed. In buffered mode, the U1 buffer directly drives the 23.1 pF capacitor and the charging time of the capacitors is negligible. In unbuffered mode, Switch S1 is closed and Switch S2 is closed. In unbuffered mode, the 23.1 pF capacitor must be charged from the I/Ox pins; this charging contributes to the input current. For applications where the ADC input current is too high, an external input buffer may be required. The choice of buffer is a function of the particular application. (10,000 × 5.8 × 10−12 × 1.5) + 1 nA = 88 nA Under the same conditions, the ADC input current in unbuffered mode is as follows: (10,000 × 28.9 × 10−12 × 1.5) = 433.5 nA S1 I/O7 S2 5.8pF U1 300Ω S3 CONTROL LOGIC 23.1pF S4 COMPARATOR Figure 33. ADC Input Structure Rev. B | Page 19 of 33 12507-033 MUX I/O0 AD5593R Data Sheet GPIO SECTION Each of the eight I/Ox pins can be configured as a generalpurpose digital input or output pin by programming the GPIO control register. When an I/Ox pin is configured as an output, the pin can be set high or low by programming the GPIO write data register. Logic levels for general-purpose outputs are relative to VDD and GND. When an I/Ox pin is configured as an input, its status can be determined by reading the GPIO read configuration register. When an I/Ox pin is set as an output, it is possible to read its status by also setting it as an input pin. When reading the status of the I/Ox pins set as inputs the status of an I/Ox pin set as both and input and output pin is also returned. INTERNAL REFERENCE The AD5593R contains an on-chip 2.5 V reference. The reference is powered down by default and is enabled by setting Bit D9 in the power-down/reference control register to 1. When the on-chip reference is powered up, the reference voltage appears on the VREF pin and may be used as a reference source for other components. When the internal reference is used, it is recommended to decouple VREF to GND using a 100 nF capacitor. It is recommended that the internal reference be buffered before using it elsewhere in the system. When the reference is powered down, an external reference must be connected to VREF. Suitable external reference sources for the AD5593R include the AD780, AD1582, ADR431, REF193, and ADR391. RESET FUNCTION The AD5593R has an asynchronous RESET pin. For normal operation, RESET is tied high. A falling edge on RESET resets all registers to their default values and reconfigures the I/O pins to their default values (85 kΩ pull-down resistor to GND). The reset function takes 250 μs maximum; do not write new data to the AD5593R during this time. The AD5593R has a software reset that performs the same function as the RESET pin. The reset function is activated by writing 0x0F to the pointer byte and 0x0D and 0xAC to the most significant and least significant bytes, respectively. TEMPERATURE INDICATOR The AD5593R contains an integrated temperature indicator that can be read to provide an estimation of the die temperature. This can be used in fault detection where a sudden rise in die temperature may indicate a fault condition, such as a shorted output. Temperature readback is enabled by setting Bit D8 in the ADC sequence register. The temperature result is then added to the ADC sequence. The temperature result has an address of 0b1000 and care must be taken that this result is not confused with the readback from DAC0. The temperature conversion takes 5 μs with the ADC buffer enabled and 20 μs when the buffer is disabled. Calculate the temperature using the following formulae: For ADC gain = 1, Temperature (°C) = 25 + ADC Code 820 2.654 For ADC gain = 2, Temperature (°C) = 25 + ADC Code 410 2.654 The range of codes returned by the ADC when reading from the temperature indicator is approximately 645 to 1035, corresponding to a temperature between −40°C to +105°C. The accuracy of the temperature indicator is typically 3°C when averaged over five samples. Rev. B | Page 20 of 33 Data Sheet AD5593R SERIAL INTERFACE The AD5593R has a 2-wire, I2C-compatible serial interface (refer to The I2C -Bus Specification, Version 2.1, January 2000). The AD5593R is connected to an I2C bus as a slave device under the control of a master device. See Figure 2 for a timing diagram of a typical write sequence. The AD5593R supports standard mode (100 kHz) and fast mode (400 kHz). Support is not provided for 10-bit addressing and general call addressing. The AD5593R has a 7-bit slave address; its six MSBs are set to 001000. The LSB is set by the state of the A0 address pin, which determines the state of the A0 bit. The facility to change the logic level of the A0 pin before a read or write operation allows the user to incorporate multiple AD5593R devices on one bus. WRITE OPERATION When writing to the AD5593R, the user must begin with a start command followed by an address byte R/W = 0), after which the AD5593R acknowledges that it is prepared to receive data by pulling SDA low. The AD5593R requires three bytes of data. The first byte is the pointer byte. This byte contains information defining the type of operation that is required of the AD5593R, such as configuring the I/O pins and writing to a DAC. The pointer byte is followed by the most significant byte and the least significant byte, as shown in Figure 34. After these data bytes are acknowledged by the AD5593R, a stop condition follows. READ OPERATION The 2-wire serial bus protocol operates as follows: the master initiates data transfer by establishing a start condition when a high-to-low transition on the SDA line occurs while SCL is high. The following byte is the address byte, which consists of the 7-bit slave address. The slave address corresponding to the transmitted address responds by pulling SDA low during the ninth clock pulse (this is termed the acknowledge bit). At this stage, all other devices on the bus remain idle while the selected device waits for data to be written to or read from its shift register. When reading data back from the AD5593R, the user begins with a start command followed by an address byte (R/W = 0), after which the DAC acknowledges that it is prepared to transmit data by pulling SDA low. The pointer byte is then written to select what is to be read back. A repeat start or a new I2C transmission can then follow to read two bytes of data from the AD5593R. Both bytes are acknowledged by the master, as shown in Figure 35. It is also possible to perform consecutive readbacks without having to provide interim start and stop conditions or slave addresses. This method can be used to read blocks of conversions from the ADC, as shown in Figure 37. Data is transmitted over the serial bus in sequences of nine clock pulses (eight data bits followed by an acknowledge bit). The transitions on the SDA line must occur during the low period of SCL and remain stable during the high period of SCL. When all data bits have been read or written, a stop condition is established. In write mode, the master pulls the SDA line high during the 10th clock pulse to establish a stop condition. In read mode, the master issues a no acknowledge for the ninth clock pulse (that is, the SDA line remains high). The master brings the SDA line low before the 10th clock pulse and then high during the 10th clock pulse to establish a stop condition. 1 9 1 9 SCL 0 SDA 0 START BY MASTER 1 0 0 0 A0 D7 R/W D6 D5 ACK. BY AD5593R FRAME 1 SLAVE ADDRESS 1 9 D4 D3 D2 D1 D0 ACK. BY AD5593R FRAME 2 POINTER BYTE 1 9 SCL (CONTINUED) DB15 DB14 DB13 DB12 DB11 DB10 DB9 FRAME 3 MOST SIGNIFICANT DATA BYTE DB8 DB7 DB6 ACK. BY AD5593R Figure 34. 4-Byte I2C Write Rev. B | Page 21 of 33 DB5 DB4 DB3 DB2 FRAME 4 LEAST SIGNIFICANT DATA BYTE DB1 DB0 ACK. BY AD5593R STOP BY MASTER 12507-013 SDA (CONTINUED) AD5593R Data Sheet 1 9 1 9 SCL 0 SDA 0 1 0 START BY MASTER 0 0 A0 W D7 D6 D5 ACK. BY AD5593R FRAME 1 SLAVE ADDRESS 1 D4 D3 D2 D1 D0 ACK. BY AD5593R FRAME 2 POINTER BYTE 9 1 STOP BY MASTER 9 SCL (CONTINUED) SDA (CONTINUED) 0 0 1 0 0 0 A0 START BY MASTER R D15 D14 D13 ACK. BY AD5593R D11 D10 D9 D8 ACK. BY MASTER FRAME 2 MOST SIGNIFICANT DATA BYTE FRAME 1 SLAVE ADDRESS 1 D12 9 SCL (CONTINUED) D7 D6 D5 D4 D3 D2 D1 D0 NACK. BY MASTER FRAME 3 LEAST SIGNIFICANT DATA BYTE STOP BY MASTER 12507-014 SDA (CONTINUED) Figure 35. Read One 16-Bit Word 1 9 1 9 SCL 0 SDA 0 1 0 0 0 A0 D7 W START BY MASTER D6 D5 D4 D3 D2 D1 D0 ACK. BY AD5593R ACK. BY AD5593R FRAME 1 SLAVE ADDRESS FRAME 2 POINTER BYTE 1 9 1 9 SCL (CONTINUED) SDA (CONTINUED) 0 0 1 0 0 0 A0 R REPEAT START BY MASTER D15 ACK. BY AD5593R FRAME 1 SLAVE ADDRESS 1 D14 D13 D12 D11 D10 FRAME 2 MOST SIGNIFICANT DATA BYTE D9 D8 ACK. BY MASTER 9 SCL (CONTINUED) D7 D6 D5 D4 D3 D2 FRAME 3 LEAST SIGNIFICANT DATA BYTE D1 D0 NACK. BY MASTER STOP BY MASTER Figure 36. Read One 16-Bit Word, Maintain Control of the Bus Rev. B | Page 22 of 33 12507-015 SDA (CONTINUED) Data Sheet AD5593R 1 9 1 9 SCL 0 SDA 0 1 0 0 0 A0 W START BY MASTER D7 D6 D5 D4 D3 D2 D1 D0 ACK. BY AD5593R ACK. BY AD5593R FRAME 1 SLAVE ADDRESS FRAME 2 POINTER BYTE START OF ADC CONVERSION1 1 9 1 9 SCL (CONTINUED) SDA (CONTINUED) 0 0 1 0 0 0 A0 R D15 D14 D13 ACK. BY AD5593R REPEAT START BY MASTER 9 D11 D10 D9 D8 ACK. BY MASTER FRAME 2 MOST SIGNIFICANT DATA BYTE FRAME 1 SLAVE ADDRESS 1 D12 1 9 SCL (CONTINUED) SDA (CONTINUED) D7 D6 D5 D4 D3 D2 D1 D15 D0 D14 ACK. BY MASTER FRAME 3 LEAST SIGNIFICANT DATA BYTE 1 D13 D12 D11 D10 FRAME 4 MOST SIGNIFICANT DATA BYTE D9 D8 ACK. BY MASTER 9 SCL (CONTINUED) D7 D6 D5 D4 D3 D2 D1 D0 ACK. BY MASTER FRAME 5 LEAST SIGNIFICANT DATA BYTE 1ONLY STOP BY MASTER 12507-016 SDA (CONTINUED) APPLICABLE IF AN ADC SEQUENCE HAS BEEN SELECTED. Figure 37. I2C Block Read POINTER BYTE CONTROL REGISTERS The pointer byte contains eight bits. Bits[D7:D4] are mode bits that select the operation to be executed. The data contained in Bits[D3:D0] depend on the operation required. Table 9 shows the configuration of the pointer byte. When Bits[D7:D4] are 0b0000, the mode dependent bits (Bits[D3:D0]) select a control register to write data to. The data written to a control register is contained in the MSB and LSB as shown in Figure 34. The mode dependent data bits also select which DAC is updated during a DAC write operation and which register is selected for readback. Table 11 shows the control register map for the AD5593R. The control registers configure the I/O pins and set various operating parameters in the AD5593R, such as enabling the reference, selecting the LDAC mode function, or selecting power-down modes. The control registers are written to using the 4-byte I2C write sequence shown in Figure 34. To write to a control register, the mode bits (Bits[D7:D4]) of the pointer byte are zeros. The mode dependent data bits (Bits[D3:D0]) of the pointer byte select which control register is to be accessed. The data to be written to the control register is contained in the most significant and least significant data bytes. These contain a total of 16 bits and are shown as D15 to D0 in Table 12 and Table 13. The contents of the control registers can be read back using the read sequence shown in Figure 35 or Figure 36. Table 9. Pointer Byte Configuration D7 D6 D5 Mode bits D4 D3 D2 D1 D0 Mode dependent data bits Table 10. Mode Bits D7 0 0 0 0 0 0 D6 0 0 1 1 1 1 D5 0 0 0 0 1 1 D4 0 1 0 1 0 1 Description Configuration mode DAC write ADC readback DAC readback GPIO readback Register readback Rev. B | Page 23 of 33 AD5593R Data Sheet GENERAL-PURPOSE CONTROL REGISTER The general-purpose control register enables or disables certain functions associated with the DAC, ADC, and I/O pin configuration (see Table 13). The register sets the output range of the DAC and input range of the ADC, which sets their transfer functions, enables/disables the ADC buffer, and enables the precharge function (see the ADC Section for more details). The register is also used to lock the I/O pin configuration to prevent accidental change. When Bit D7 is set to 1, writes to the configuration registers are ignored. Table 11. Control Registers Pointer Byte [D7:D0] 00000000 00000010 00000011 00000100 00000101 00000110 00000111 00001000 00001001 00001010 00001011 00001100 00001101 00001110 00001111 Register Name NOP ADC sequence register General-purpose control register ADC pin configuration DAC pin configuration Pull-down configuration LDAC mode GPIO write configuration GPIO write data GPIO read configuration Power-down/reference control Open-drain configuration Three-state pins Reserved Software reset Description No operation Selects ADCs for conversion DAC and ADC control register Selects which pins are ADC inputs Selects which pins are DAC outputs Selects which pins have an 85 kΩ pull-down resistor to GND Selects the operation of the load DAC Selects which pins are general-purpose outputs Writes data to general-purpose outputs Selects which pins are general-purpose inputs Powers down the DACs and enables/disables the reference Selects open-drain or push-pull for general-purpose outputs Selects which pins are three-stated Default Value 0x0000 0x0000 0x0000 0x0000 0x0000 0x00FF 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Resets the AD5593R 0x0000 Table 12. General-Purpose Control Register MSB D15 D14 D13 D12 Reserved D11 D10 D9 ADC buffer precharge D8 ADC buffer enable D7 Lock configuration D6 Write all DACs D5 ADC range select D4 DAC range select D3 D2 D1 Reserved LSB D0 Table 13. General-Purpose Control Register Descriptions Bits D15 to D10 D9 D8 D7 D6 D5 D4 D3 to D0 Description Reserved. Set these bits to 0. ADC buffer precharge. 0: the ADC buffer is not used to precharge the ADC. If the ADC buffer is enabled, it is always powered up (default). 1: the ADC buffer is used to precharge the ADC. If the ADC buffer is enabled, it is powered up while the conversion takes place and then powered down until the next conversion takes place. ADC buffer enable. 0: the ADC buffer is disabled (default). 1: the ADC buffer is enabled. Lock configuration. 0: the contents of the I/O pin configuration registers can be changed (default). 1: the contents of the I/O pin configuration registers cannot be changed. Write all DACs. 0: for future DAC writes, the DAC address bits determine which DAC is written to (default). 1: for future DAC writes, the DAC address bits are ignored and all channels configured as DACs are updated with the same data. ADC range select. 0: the ADC range is 0 to VREF (default). 1: the ADC range is 0 to 2 × VREF. DAC range select. 0: the DAC range is 0 to VREF (default). 1: the DAC range is 0 to 2 × VREF. Reserved; set these bits to 0. Rev. B | Page 24 of 33 Data Sheet AD5593R The exceptions to this rule are that an I/Ox pin can be set as both a DAC and ADC or as a digital input and output. When an I/Ox pin is configured as a DAC and ADC, the primary function is as a DAC and the ADC can be used to measure the voltage being provided by the DAC. This feature can be used to monitor the output voltage to detect short circuits or overload conditions. Figure 38 shows an example of how to configure I/O1 and I/O7 as DACs. When a pin is configured as both a general-purpose input and output, the primary function is as an output pin. This configuration allows the status of the output pin to be determined by reading the GPIO read configuration register. CONFIGURING THE AD5593R The AD5593R I/O pins are configured by writing to a series of pin configuration registers. The control registers are accessed when Bits[D7:D4] are 0b0000. Bits[D3:D0] determine which register is accessed as shown in Table 11. On power-up, the I/O pins are configured as 85 kΩ resistors connected to GND. The I/O channels of the AD5593R can be configured to operate as DAC outputs, ADC inputs, digital outputs, digital inputs, three-state, or connected to GND with 85 kΩ pull-down resistors. When configured as digital outputs, the pins have the additional option of being configured as push/pull or open-drain. The general-purpose control register contains a lock configuration bit. When the lock configuration bit is set to 1, any writes to the pin configuration registers are ignored, thus preventing the function of the I/O pins from being changed. The I/O channels are configured by writing to the appropriate configuration registers, as shown in Table 11. To assign a particular function for an I/O channel, write to the appropriate register and set the corresponding bit to 1. For example, setting Bit D0 in the DAC configuration register configures I/O0 as a DAC. In the event that the bit for an I/O channel is set in multiple configuration registers, the I/O channel adopts the function dictated by the last write operation. The I/O pins can be reconfigured any time when the AD5593R is in an idle state, that is, no ADC conversions are taking place and no registers are being read back. The lock configuration bit must also be set to 0. Table 14. I/O Pin Configuration Registers1 D7 I/O7 D5 I/O5 D4 I/O4 D3 I/O3 D2 I/O2 D1 I/O1 D0 I/O0 Setting an I/O pin configuration bit to 1 after writing to a control register enables that function on the selected I/O pin. MOST SIGNIFICANT DATA BYTE POINTER BYTE S SLAVE ADDRESS + W A 0b00000101 A 0b00000000 LEAST SIGNIFICANT DATA BYTE A 0b10000010 A P S = START CONDITION P = STOP CONDITION A = ACKNOWLEDGE Figure 38. Configuring I/O1 and I/O7 as DACs Rev. B | Page 25 of 33 12507-017 1 D6 I/O6 AD5593R Data Sheet DAC WRITE OPERATION DAC READBACK Data is written to a DAC when the mode bits (Bits[D7:D4]) of the pointer byte are 0b0001 (see Table 10). Bits[D2:D0] determine which DAC is addressed. Data to be written to the DAC is contained in the MSB and LSB, as shown in Table 17. Data is written to the selected DAC input register. Data written to the input register can be automatically copied to the DAC register, if required. Data is transferred to the DAC register based on the setting of the LDAC mode register (see Table 15). The input register of each DAC can be read back via the I2C interface. This can be useful to confirm that the data was received correctly before writing to the LDAC register or simply checking what value was last loaded to a DAC. Data can be read back from a DAC only when no ADC conversion sequence is taking place. A DAC input register can be read back using the sequence shown in Figure 35 or Figure 36. The mode bits, Bits[D3:D0], of the pointer register, 0b0101, select which DAC input register is to be read back. When the DAC register is read back, the MSB of the most significant data byte is a 1 to indicate that the result is a DAC register. The next three bits (Bits[D14:D12]) contain the DAC register address (see Table 17) and Bits[D11:D0] contain the DAC register value. Figure 39 shows an example of reading the input register of DAC2. LDAC Mode Operation The transfer of data from an input register to a DAC register is controlled by Bit D1 and Bit D0 of the readback and LDAC mode register (pointer byte = 0b00000111). When the LDAC mode bits (Bit D1 and Bit D0) are set to 00, new data is automatically transferred from the input register to the DAC register and the analog output updates. When the LDAC mode bits are set to 01, data remains in the input register. This allows writes to input registers without affecting the analog outputs. After loading the input registers with the desired values and setting the LDAC mode bits to 10, the values in the input registers transfer to the DAC registers and the analog outputs update simultaneously. The LDAC mode bits then revert to 01. Table 16. DAC Pointer Byte Address DAC Address DAC0 DAC1 DAC2 DAC3 DAC4 DAC5 DAC6 DAC7 Table 15. LDAC Mode Register D1 0 D0 0 0 1 1 0 1 1 LDAC Mode Data written to an input register is immediately copied to a DAC register and the DAC output updates (default). Data written to an input register is not copied to a DAC register. The DAC output is not updated. Data in the input registers is copied to the corresponding DAC registers. When the data has been transferred, the DAC outputs are updated simultaneously. Reserved. D7 D6 D5 D4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 D3 0 0 0 0 0 0 0 0 D2 0 0 0 0 1 1 1 1 D1 0 0 1 1 0 0 1 1 D0 0 1 0 1 0 1 0 1 Table 17. DAC Data Register D14 D13 D12 DAC address D11 D10 D9 D8 D7 D6 D5 12-bit DAC data D4 D3 D2 D1 POINTER BYTE S SLAVE ADDRESS + W A 0b01010010 DACADDRESS AND 4 MSBs 0b1010XXX A RS SLAVE ADDRESS + R DAC LSBs A 0bXXXXXXX A P Figure 39. DAC Input Register Readback Rev. B | Page 26 of 33 S = START CONDITION P = STOP CONDITION A = ACKNOWLEDGE RS = REPEAT START A 12507-018 MSB D15 1 LSB D0 Data Sheet AD5593R sequence. If the REP bit is clear, the ADC clocks out the last result on subsequent I2C reads. When ADC data is clocked out by the serial interface, D15 = 0 to indicate that the result is ADC data. D14 to D12 contain a 3-bit address to indicate which ADC the data is coming from, and D11 to D0 contain the 12-bit ADC result (see Table 20). ADC OPERATION The ADC channels of the AD5593R operate as a traditional multichannel ADC, where each serial transfer selects the next channel for conversion. The user must write to the ADC sequence register (see Table 19) to select the input channels to be included in the conversion sequence before initiating any conversions. This is done using the I2C write sequence shown in Figure 34. When writing to the ADC sequence register, select which channels are to be converted in sequence. The user can also set the REP bit to have the ADC repeat conversions in the sequence. Figure 40 shows how to configure the AD5593R to perform ADC conversions. In Step 1, I/O7 and I/O0 are configured as ADCs. Step 2 writes to the ADC configuration register, sets the REP bit, and selects ADC7 and ADC0 for inclusion in the conversion sequence. Step 3 selects the ADCs for reading and Step 4 begins reading the ADC results. The conversions are repeated until a stop condition is given by the controller. When the sequence register has been written to, the ADC begins to track the first channel in the sequence. ADC data can be read from the AD5593R using any of the three read operations shown in Figure 35, Figure 36, and Figure 37, with the I2C block read (Figure 37) being the most efficient. The ADC sequence can be changed by writing the new sequence to the ADC sequence register when conversions are not taking place. When a new sequence is written, any channels remaining to be converted from the earlier sequence are ignored and the ADC starts converting the first channel of the new sequence. If more than one channel is selected in the ADC sequence register, the ADC converts all selected channels sequentially in ascending order. Conversion is started by the rising edge of SCL at the acknowledge (ACK) preceding the MSB (see Figure 37). To stop the ADC conversion sequence, clear the REP, TEMP, and ADC7 to ADC0 bits in the ADC sequence register to 0. If the REP bit is set after all of the selected channels in the sequence register have been converted, the ADC repeats the Table 18. ADC Sequence Register MSB D15 D14 D13 D12 Reserved D11 D10 D9 REP D8 TEMP D7 ADC7 D6 ADC6 D5 ADC5 D4 ADC4 D3 ADC3 D2 ADC2 D1 ADC1 LSB D0 ADC0 Table 19. ADC Sequence Register Descriptions Bits D15 to D10 D9 D8 D7 to D0 Description Reserved; set this bit to 0 REP: ADC sequence repeat 0 = sequence repetition disabled (default) 1 = sequence repetition enabled TEMP: include temperature indicator in ADC sequence 0 = disable temperature indicator readback (default) 1 = enable temperature indicator readback Setting these bits to 1 includes the appropriate ADC in the conversion sequence; by default no channels are included Table 20. ADC Data Register MSB D15 0 D14 D13 D12 ADC address D11 D10 D9 D8 D7 Rev. B | Page 27 of 33 D6 D5 12-bit ADC data D4 D3 D2 D1 LSB D0 AD5593R Data Sheet LEAST SIGNIFICANT DATA BYTE S SLAVE ADDRESS + W A 0b00000100 A 0b00000000 A 0b10000001 A P STEP2 S SLAVE ADDRESS + W A 0b00000010 A 0b00000010 A 0b10000001 A P STEP3 S SLAVE ADDRESS + W A 0b01000000 A P STEP4 S SLAVE ADDRESS + R A ADC7 RESULT (MSB) A ADC7 RESULT (LSB) A ADC0 RESULT (MSB) A ADC0 RESULT (LSB) A ADC7 RESULT (MSB) A ADC0 RESULT (MSB) A ADC0 RESULT (LSB) A P Figure 40. Configuring the ADC for Conversion Rev. B | Page 28 of 33 ADC7 RESULT (LSB) S = START CONDITION P = STOP CONDITION A = ACKNOWLEDGE A 12507-019 MOST SIGNIFICANT DATA BYTE POINTER BYTE STEP1 Data Sheet AD5593R GPIO OPERATION Table 23. GPIO Write Data Register Descriptions Each of the I/Ox pins of the AD5593R can be configured to operate as a general-purpose, digital input or output pin. The function of the pins is determined by writing to the appropriate bit in the GPIO read configuration and GPIO write configuration registers using the 4-byte I2C write shown in Figure 34. Bits D15 to D8 D7 to D0 Setting Pins as Outputs Setting Pins as Inputs To set a pin as a general-purpose output, set the appropriate bit in the GPIO write configuration register to 1. For example, setting Bit D0 to 1 enables I/O0 as a general-purpose output. To set an I/Ox pin as a general-purpose input, set the appropriate bit in the GPIO read configuration register to 1. For example, setting Bit D0 to 1 enables I/O0 as a general-purpose input. To read the state of general-purpose inputs, set the pointer byte to 0b01100000 (see Table 10 ) using any of the read operations shown in Figure 35, Figure 36, and Figure 37. The status of any I/O pin set as a general-purpose input appears in the appropriate bit location in the least significant data byte. The outputs can be independently configured as push/pull or open-drain outputs. When in push/pull configuration, the output is driven to VDD or GND as determined by the data in the GPIO write data register. When in open-drain configuration, the output is driven to GND when a data bit in the GPIO write data register sets the pin low. When the pin is set high, the output is not driven and must be pulled high by an external resistor. This allows multiple output pins to be tied together. If all the pins are normally high, it allows one pin to pull down the others. This is commonly used where multiple pins are used to trigger an alarm or interrupt pin. The state of the output pin is controlled by setting or clearing the bits in the GPIO write data register (pointer byte = 0b00001001). A data bit is ignored if it is written to a location that is not configured as an output. Three-State Pins The I/Ox pins can be set to three-state by writing to the threestate configuration register (pointer byte = 0b00001101) as shown in Table 24. Table 24. Three-State Configuration Register Descriptions Bits D15 to D8 D7 to D0 Table 21. GPIO Write Configuration Register Descriptions Bits D15 to D8 D7 to D0 Description Reserved; set these bits to 0 Select pins as GPIO outputs D[7:0] = 1: I/O[7:0] is a general-purpose output pin D[7:0] = 0: I/O[7:0] function is determined by the pin configuration registers (default) Description Reserved; set these bits to 0 Sets the state of a GPIO output D[7:0] = 1: I/O[7:0] is a Logic 1 D[7:0] = 0: I/O[7:0] is a Logic 0 (default) Description Reserved; set these bits to 0 Set pins as three-state outputs D[7:0] = 1: I/O[7:0] is a three-state output pin D[7:0] = 0: I/O[7:0] function is determined by the pin configuration registers (default) 85 kΩ Pull-Down Pins The I/Ox pins can be connected to GND via a pull-down resistor (85 kΩ) by setting the appropriate bits in the pull-down configuration register (pointer byte = 00000110) as shown in Table 25. Table 22. GPIO Open-Drain Control Register Descriptions Bits D15 to D8 D7 to D0 Description Reserved; set these bits to 0 Sets output pins as open-drain D[7:0] = 1: I/O[7:0] is an open-drain output pin D[7:0] = 0: I/O[7:0] is a push/pull output pin (default) Table 25. Pull-Down Configuration Register Descriptions Bits D15 to D8 D7 to D0 Rev. B | Page 29 of 33 Description Reserved; set these bits to 0 Set pins as weak pull-down outputs D[7:0] = 1: I/O[7:0 is connected to GND via an 85 kΩ pull-down resistor D[7:0] = 0: I/O[7:0] function is determined by the pin configuration registers (default) AD5593R Data Sheet POWER-DOWN/REFERENCE CONTROL RESET FUNCTION The AD5593R has a power-down/reference control register (pointer byte = 0b00001011) that reduces the power consumption when certain functions are not needed. The power-down register allows any channels set as DACs to be placed in a power-down state individually. When in power-down, the DAC outputs are three-stated. When a DAC channel is returned into normal mode, the DAC output returns to its previous value. The internal reference and its buffer are powered down by default and are enabled by setting the EN_REF bit in the power-down register. The internal reference voltage then appears at the VREF pin. The AD5593R can be reset to its default conditions by writing 0x0DAC to the reset register (pointer byte = 0b00001111). This resets all registers to their default values and reconfigures the I/Ox pins to their default values (85 kΩ pull-down to GND). The reset function is triggered on the SCL falling edge of the eighth bit of the least significant byte (DB0 of Frame 4 in Figure 34), and the AD5593R does not generate an ACK signal for this byte of data. The reset function takes 100 μs maximum and new data must not be written to the AD5593R during this time. The AD5593R has a RESET pin that performs the same function. For normal operation, RESET is tied high. A falling edge on RESET triggers the reset function. There is no dedicated power-down function for the ADC, but the ADC is automatically powered down if none of the I/Ox pins are selected as ADCs. The ADC powers up if a read of the temperature indicator is initiated. The PD_ALL bit powers down all the DACs, the reference, its buffer, and the ADC. The PD_ALL bit also overrides the settings of Bit D9 to Bit D0. Table 26 shows the power-down register. Table 26. Power-Down Register MSB D15 0 D14 0 D13 0 D12 0 D11 0 D10 PD_ALL D9 EN_REF D8 0 D7 PD7 D6 PD6 D5 PD5 D4 PD4 D3 PD3 D2 PD2 D1 PD1 Table 27. LDAC Mode Register Descriptions Bits D15 to D11 D10 Bit Name Reserved PD_ALL D9 EN_REF D7 to D0 PD7 to PD0 Description Reserved; set these bits to 0 0 = the power-down states of the reference and DACs are determined by D9 and D7 to D0 (default). 1 = the reference, the DACs, and the ADC are powered down. 0 = the reference and its buffer are powered down (default). Set this bit if an external reference is used. 1 = the reference and its buffer are powered up. The reference is available on the VREF pin. 0 = the channel is in normal operating mode (default). 1 = the channel is powered down if it is configured as a DAC. Rev. B | Page 30 of 33 LSB D0 PD0 Data Sheet AD5593R APPLICATIONS INFORMATION MICROPROCESSOR INTERFACING LAYOUT GUIDELINES Microprocessor interfacing to the AD5593R is via a serial bus using a standard I2C protocol. The communications channel requires a 2-wire interface consisting of a clock signal and a data signal. In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to ensure the rated performance. The printed circuit board (PCB) on which the AD5593R is mounted must be designed so that the AD5593R lies on the analog plane. AD5593R TO ADSP-BF537 INTERFACE The I2C interface of the AD5593R is designed to be easily connected to industry-standard DSPs and microcontrollers. Figure 41 shows the AD5593R connected to the Analog Devices Blackfin® DSP. The Blackfin has an integrated I2C port that can be connected directly to the I2C pins of the AD5593R. AD5593R SCL SDA SCL SDA PF8 RESET 12507-164 ADSP-BF537 The AD5593R must have ample supply bypassing of 10 μF in parallel with 0.1 μF on each supply, located as close to the package as possible, ideally right up against the device. The 10 μF capacitors are the tantalum bead type. The 0.1 μF capacitor must have low effective series resistance (ESR) and low effective series inductance (ESI) such as the common ceramic types, which provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. Figure 41. ADSP-BF537 Interface Rev. B | Page 31 of 33 AD5593R Data Sheet OUTLINE DIMENSIONS 5.10 5.00 4.90 16 9 4.50 4.40 4.30 6.40 BSC 1 8 PIN 1 1.20 MAX 0.15 0.05 0.65 BSC 0.30 0.19 0.20 0.09 SEATING PLANE COPLANARITY 0.10 0.75 0.60 0.45 8° 0° COMPLIANT TO JEDEC STANDARDS MO-153-AB Figure 42. 16-Lead Thin Shrink Small Outline Package [TSSOP] (RU-16) Dimensions shown in millimeters 0.30 0.25 0.20 0.50 BSC 16 13 12 1 4 9 TOP VIEW 0.80 0.75 0.70 PKG-004132 SEATING PLANE 0.50 0.40 0.30 8 5 BOTTOM VIEW 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.152 REF COMPLIANT TO JEDEC STANDARDS MO-220-WEED. Figure 43. 16-Lead Lead Frame Chip Scale Package [LFCSP] 3 mm × 3 mm Body and 0.75 mm Package Height (CP-16-32) Dimensions shown in millimeters Rev. B | Page 32 of 33 09-03-2013-A PIN 1 INDICATOR 3.10 3.00 SQ 2.90 Data Sheet AD5593R 2.000 1.960 SQ 1.920 3 4 2 1 A BALL A1 IDENTIFIER B 1.50 REF C TOP VIEW 0.50 BSC (BALL SIDE DOWN) BOTTOM VIEW (BALL SIDE UP) SIDE VIEW COPLANARITY 0.05 0.340 0.320 0.300 SEATING PLANE 0.270 0.240 0.210 10-17-2012-B 0.640 0.595 0.540 D Figure 44. 16-Ball Wafer Level Chip Scale Package [WLCSP] (CB-16-3) Dimensions shown in millimeters ORDERING GUIDE Model1 AD5593RBRUZ AD5593RBCPZ-RL7 AD5593RBCBZ-RL7 1 Temperature Range −40°C to +105°C −40°C to +105°C −40°C to +105°C Package Description 16-Lead TSSOP 16-Lead LFCSP 16-Ball WLCSP Package Option RU-16 CP-16-32 CB-16-3 Z = RoHS Compliant Part. I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors). ©2014–2016 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D12507-0-1/16(B) Rev. B | Page 33 of 33 Branding DM6