LINER LTC2483IDD

LTC2483
16-Bit ∆Σ ADC with Easy Drive
Input Current Cancellation and I2C Interface
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
■
Easy Drive Technology Enables Rail-to-Rail Inputs
with Zero Differential Input Current
Directly Digitizes High Impedance Sensors with
Full Accuracy
600nV RMS Noise, Independent of VREF
GND to VCC Input/Reference Common Mode Range
2-Wire I2C Interface
Simultaneous 50Hz/60Hz Rejection
2ppm (0.25LSB) INL, No Missing Codes
1ppm Offset and 15ppm Full-Scale Error
No Latency: Digital Filter Settles in a Single Cycle
Single Supply 2.7V to 5.5V Operation
Internal Oscillator
Six Addresses Available and One Global Address for
Synchronization
Available in a Tiny (3mm × 3mm) 10-Lead
DFN Package
U
APPLICATIO S
■
■
■
■
■
■
Direct Sensor Digitizer
Weight Scales
Direct Temperature Measurement
Strain Gauge Transducers
Instrumentation
Industrial Process Control
DVMs and Meters
The LTC2483 allows a wide common mode input range
(0V to VCC) independent of the reference voltage. The
reference can be as low as 100mV or can be tied directly
to VCC. The noise level is 600nV RMS independent of VREF.
This allows direct digitization of low level signals with 16bit accuracy. The LTC2483 includes an on-chip trimmed
oscillator, eliminating the need for external crystals or
oscillators and provides 87dB rejection of 50Hz and 60Hz
line frequency noise. Absolute accuracy and low drift are
automatically maintained through continuous, transparent, offset and full-scale calibration.
, LTC and LT are registered trademarks of Linear Technology Corporation.
No Latency ∆Σ and Easy Drive are trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
Patent Pending.
U
■
The LTC®2483 combines a 16-bit plus sign No Latency ∆ΣTM
analog-to-digital converter with patented Easy DriveTM technology and I2C digital interface. The patented sampling
scheme eliminates dynamic input current errors and the
shortcomings of on-chip buffering through automatic
cancellation of differential input current. This allows large
external source impedances and input signals, with rail-torail input range to be directly digitized while maintaining
exceptional DC accuracy.
TYPICAL APPLICATIO
+FS Error vs RSOURCE at IN+ and IN–
VCC
1µF
10k
IDIFF = 0
VIN+
1µF
SENSE
REF+
SCL
SDA
LTC2483
VIN–
10k
VCC
GND
REF–
CA0/F0
CA1
2-WIRE
I2C INTERFACE
6 ADDRESSES
+FS ERROR (ppm)
■
DESCRIPTIO
80
VCC = 5V
= 5V
60 VREF
VIN+ = 3.75V
–
40 VIN = 1.25V
FO = GND
20 TA = 25°C
CIN = 1µF
0
–20
–40
–60
2483 TA01
–80
1
10
100
1k
RSOURCE (Ω)
10k
100k
2483 TA02
2483f
1
LTC2483
W W
W
AXI U
U
ABSOLUTE
RATI GS
U
U
W
PACKAGE/ORDER I FOR ATIO
(Notes 1, 2)
Supply Voltage (VCC) to GND ...................... – 0.3V to 6V
Analog Input Voltage to GND ....... – 0.3V to (VCC + 0.3V)
Reference Input Voltage to GND .. – 0.3V to (VCC + 0.3V)
Digital Input Voltage to GND ........ – 0.3V to (VCC + 0.3V)
Digital Output Voltage to GND ..... – 0.3V to (VCC + 0.3V)
Operating Temperature Range
LTC2483C ................................................... 0°C to 70°C
LTC2483I ................................................ – 40°C to 85°C
Storage Temperature Range ................ – 65°C to 125°C
TOP VIEW
REF+ 1
10 CA0/F0
VCC 2
9 CA1
REF – 3
11
8 GND
IN+ 4
7 SDA
IN– 5
6 SCL
DD PACKAGE
10-LEAD (3mm × 3mm) PLASTIC DFN
TJMAX = 125°C, θJA = 43°C/ W
EXPOSED PAD (PIN 11) IS GND
MUST BE SOLDERED TO PCB
DD PART MARKING*
LBSR
ORDER PART NUMBER
LTC2483CDD
LTC2483IDD
Order Options Tape and Reel: Add #TR
Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF
Lead Free Part Marking: http://www.linear.com/leadfree/
Consult LTC Marketing for parts specified with wider operating temperature ranges.
*The temperature grade is identified by a label on the shipping container.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
Resolution (No Missing Codes)
0.1 ≤ VREF ≤ VCC, –FS ≤ VIN ≤ +FS (Note 5)
●
MIN
Integral Nonlinearity
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V (Note 6)
2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6)
●
2
1
10
Offset Error
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC (Note 13)
●
0.5
2.5
Offset Error Drift
2.5V ≤ VREF ≤ VCC, GND ≤ IN+ = IN– ≤ VCC
Positive Full-Scale Error
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF
Positive Full-Scale Error Drift
2.5V ≤ VREF ≤ VCC, IN+ = 0.75VREF, IN– = 0.25VREF
Negative Full-Scale Error
2.5V ≤ VREF ≤ VCC, IN– = 0.75VREF, IN+ = 0.25VREF
Negative Full-Scale Error Drift
2.5V ≤ VREF ≤ VCC
Total Unadjusted Error
Output Noise
, IN–
= 0.75VREF, IN+ = 0.25VREF
TYP
MAX
16
UNITS
Bits
10
●
µV
nV/°C
25
0.1
●
ppm of VREF
ppm of VREF
ppm of VREF
ppm of
VREF/°C
25
ppm of VREF
0.1
ppm of
VREF/°C
5V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6)
5V ≤ VCC ≤ 5.5V, VREF = 5V, VIN(CM) = 2.5V (Note 6)
2.7V ≤ VCC ≤ 5.5V, VREF = 2.5V, VIN(CM) = 1.25V (Note 6)
15
15
15
ppm of VREF
ppm of VREF
ppm of VREF
5V ≤ VCC ≤ 5.5V, VREF = 5V, GND ≤ IN– = IN+ ≤ VCC (Note 12)
0.6
µVRMS
2483f
2
LTC2483
U
CO VERTER CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 4)
PARAMETER
CONDITIONS
Input Common Mode Rejection DC
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Note 5)
●
140
dB
Input Common Mode Rejection
50Hz ±2%
2.5V ≤ VREF ≤
VCC, GND ≤ IN– = IN+ ≤ VCC (Note 5)
●
140
dB
Input Common Mode Rejection
60Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Note 5)
●
140
dB
Input Normal Mode Rejection
50Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Notes 5, 7)
●
110
120
dB
Input Normal Mode Rejection
60Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Notes 5, 8)
●
110
120
dB
Input Normal Mode Rejection
50Hz/60Hz ±2%
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Notes 5, 9)
●
87
Reference Common Mode
Rejection DC
2.5V ≤ VREF ≤ VCC, GND ≤ IN– = IN+ ≤ VCC (Note 5)
●
120
Power Supply Rejection DC
VREF = 2.5V, IN– = IN+ = GND
Power Supply Rejection, 50Hz ±2%
Power Supply Rejection, 60Hz ±2%
MIN
TYP
MAX
UNITS
dB
140
dB
120
dB
VREF
= 2.5V, IN–
= IN+
= GND (Notes 7, 9)
120
dB
VREF
= 2.5V, IN–
= IN+
= GND (Notes 8, 9)
120
dB
U
U
U
U
A ALOG I PUT A D REFERE CE The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
IN+
Absolute/Common Mode IN+ Voltage
CONDITIONS
GND – 0.3V
VCC + 0.3V
V
IN–
Absolute/Common Mode IN– Voltage
GND – 0.3V
VCC + 0.3V
V
FS
Full Scale of the Differential Input (IN+
– IN–)
MIN
●
0.5VREF
TYP
MAX
UNITS
V
LSB
Least Significant Bit of the Output Code
●
FS/216
VIN
Input Differential Voltage Range (IN+ – IN–)
●
–FS
+FS
V
VREF
Reference Voltage Range (REF+
●
0.1
VCC
V
CS
(IN+)
IN+
CS (IN–)
CS (VREF)
Sampling Capacitance
11
pF
IN– Sampling Capacitance
11
pF
11
pF
VREF Sampling Capacitance
DC Leakage Current
Sleep Mode, IN+ = GND
●
–10
1
10
nA
IDC_LEAK (IN–)
IN– DC Leakage Current
Sleep Mode, IN– = GND
●
–10
1
10
nA
IDC_LEAK (VREF)
REF+, REF–
Sleep Mode, VREF = VCC
●
–100
1
100
nA
IDC_LEAK
(IN+)
– REF–)
IN+
DC Leakage Current
2483f
3
LTC2483
U
U
I2C DIGITAL I PUTS A D DIGITAL OUTPUTS
The ● denotes the specifications which apply over
the full operating temperature range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
CONDITIONS
MIN
VIH
High Level Input Voltage
●
VIL
Low Level Input Voltage
●
0.3VCC
V
VIL(CA1)
Low Level Input Voltage for Address Pin
●
0.05VCC
V
VIH(CA0/F0,CA1)
High Level Input Voltage for Address Pins
●
RINH
Resistance from CA0/F0,CA1 to VCC to Set
Chip Address Bit to 1
●
10
kΩ
RINL
Resistance from CA1 to GND to Set
Chip Address Bit to 0
●
10
kΩ
RINF
Resistance from CA0/F0, CA1 to VCC or
GND to Set Chip Address Bit to Float
●
II
Digital Input Current
VHYS
Hysteresis of Schmitt Trigger Inputs
(Note 5)
VOL
Low Level Output Voltage SDA
I = 3mA
tOF
Output Fall Time from VIHMIN to VILMAX
Bus Load CB 10pF to 400pF (Note 14) ●
tSP
Input Spike Suppression
IIN
Input Leakage
CI
Capacitance for Each I/O Pin
●
CB
Capacitance Load for Each Bus Line
CCAX
External Capacitive Load on Chip
Address Pins (CA0/F0,CA1) for Valid Float
VIH(EXT,OSC)
High Level CA0/F0 External Oscillator
2.7V ≤ VCC < 5.5V
●
VIL(EXT,OSC)
Low Level CA0/F0 External Oscillator
2.7V ≤ VCC < 5.5V
●
●
0.1VCC ≤ VIN ≤ VCC
TYP
MAX
0.7VCC
UNITS
V
0.95VCC
V
2
MΩ
–10
10
0.05VCC
µA
V
●
20+0.1CB
0.4
V
250
ns
●
50
ns
●
1
µA
●
400
pF
●
10
pF
10
pF
VCC – 0.5V
V
0.5
V
U W
POWER REQUIRE E TS
The ● denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
VCC
Supply Voltage
ICC
Supply Current
CONDITIONS
MIN
●
Conversion Mode (Note 11)
Sleep Mode (Note 11)
●
●
TYP
MAX
5.5
V
160
1
250
2
µA
µA
2.7
UNITS
2483f
4
LTC2483
UW
TI I G CHARACTERISTICS
The ● denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 3)
SYMBOL
PARAMETER
MAX
UNITS
fEOSC
External Oscillator Frequency Range
CONDITIONS
●
MIN
10
4000
kHz
tHEO
External Oscillator High Period
●
0.125
100
µs
tLEO
External Oscillator Low Period
●
0.125
tCONV_1
Conversion Time
●
●
144.1
Simultaneous 50Hz/60Hz
External Oscillator (Note 10)
TYP
µs
100
146.9
149.9
41036/fEOSC
ms
ms
WU
I2C TI I G CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Notes 3, 15)
SYMBOL
PARAMETER
fSCL
SCL Clock Frequency
CONDITIONS
●
0
tHD(SDA)
Hold Time (Repeated) START Condition
●
0.6
µs
tLOW
LOW Period of the SCL Clock Pin
●
1.3
µs
tHIGH
HIGH Period of the SCL Clock Pin
●
0.6
µs
tSU(STA)
Set-Up Time for a Repeated START Condition
●
0.6
µs
tHD(DAT)
Data Hold Time
●
0
tSU(DAT)
Data Set-Up Time
●
100
tr
Rise Time for Both SDA and SCL Signals
(Note 14)
●
20+0.1CB
300
ns
tf
Fall Time for Both SDA and SCL Signals
(Note 14)
●
20+0.1CB
300
ns
tSU(STO)
Set-Up Time for STOP Condition
●
0.6
Note 1: Absolute Maximum Ratings are those values beyond which the life
of the device may be impaired.
Note 2: All voltage values are with respect to GND.
Note 3: VCC = 2.7V to 5.5V unless otherwise specified.
VREF = REF+ – REF–, VREFCM = (REF+ + REF–)/2, FS = 0.5VREF;
VIN = IN+ – IN–, VINCM = (IN+ + IN–)/2.
Note 4: Use internal conversion clock or external conversion clock source
with fEOSC = 307.2kHz unless otherwise specified.
Note 5: Guaranteed by design, not subject to test.
Note 6: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
Note 7: 50Hz fEOSC = 256kHz ±2% (external oscillator).
MIN
TYP
MAX
UNITS
400
kHz
µs
0.9
ns
µs
Note 8: 60Hz fEOSC = 307.2kHz ±2% (external oscillator).
Note 9: Simultaneous 50Hz/60Hz (internal oscillator) or fEOSC = 280kHz
±2% (external oscillator).
Note 10: The external oscillator is connected to the CA0/F0 pin. The
external oscillator frequency, fEOSC, is expressed in kHz.
Note 11: The converter uses the internal oscillator.
Note 12: The output noise includes the contribution of the internal
calibration operations.
Note 13: Guaranteed by design and test correlation.
Note 14: CB = capacitance of one bus line in pF.
Note 15: All values refer to VIH(MIN) and VIL(MAX) levels.
2483f
5
LTC2483
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Integral Nonlinearity
(VCC = 5V, VREF = 5V)
–45°C
1
25°C
0
85°C
–1
–2
3
VCC = 5V
VREF = 2.5V
VIN(CM) = 1.25V
2
INL (ppm OF VREF)
2
INL (ppm OF VREF)
3
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
Integral Nonlinearity
(VCC = 2.7V, VREF = 2.5V)
1
–45°C, 25°C, 90°C
0
–1
2
–3
–1.25
2.5
1
–45°C, 25°C, 90°C
0
–1
–2
–2
–3
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
2
INL (ppm OF VREF)
3
Integral Nonlinearity
(VCC = 5V, VREF = 2.5V)
–0.75
–3
–1.25
1.25
–0.25
0.25
0.75
INPUT VOLTAGE (V)
–0.75
1.25
–0.25
0.25
0.75
INPUT VOLTAGE (V)
2483 G03
2483 G01
2483 G02
Total Unadjusted Error
(VCC = 5V, VREF = 5V)
8
8
85°C
4
–45°C
–4
–8
4
–45°C
0
–4
2
–12
–1.25
2.5
–0.75
–4
–12
–1.25
1.25
–0.25
0.25
0.75
INPUT VOLTAGE (V)
4
2
1.2
1.8
2483 G07
1.25
5
VCC = 5V, VREF = 5V, VIN = 0V, VIN(CM) = 2.5V
4 TA = 25°C, RMS NOISE = 0.60µV
10,000 CONSECUTIVE
READINGS
RMS = 0.59µV
12
VCC = 2.7V
AVERAGE = –0.19µV
VREF = 2.5V
10 VIN = 0V
TA = 25°C
3
8
6
4
2
1
0
–1
–2
–3
2
0
–0.25
0.25
0.75
INPUT VOLTAGE (V)
Long-Term ADC Readings
ADC READING (µV)
NUMBER OF READINGS (%)
6
–0.75
2483 G06
14
8
–45°C
0
Noise Histogram (7.5sps)
14
–3 –2.4 –1.8 –1.2 –0.6 0 0.6
OUTPUT READING (µV)
4
85°C
2483 G05
Noise Histogram (6.8sps)
10,000 CONSECUTIVE
READINGS
12
RMS = 0.60µV
VCC = 5V
AVERAGE = –0.69µV
VREF = 5V
10 VIN = 0V
TA = 25°C
25°C
–8
2483 G04
NUMBER OF READINGS (%)
8
–8
–12
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5
INPUT VOLTAGE (V)
VCC = 2.7V
VREF = 2.5V
VIN(CM) = 1.25V
25°C
25°C
0
12
VCC = 5V
VREF = 2.5V
VIN(CM) = 1.25V
85°C
TUE (ppm OF VREF)
TUE (ppm OF VREF)
12
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
Total Unadjusted Error
(VCC = 2.7V, VREF = 2.5V)
TUE (ppm OF VREF)
12
Total Unadjusted Error
(VCC = 5V, VREF = 2.5V)
–4
–5
0
–3 –2.4 –1.8 –1.2 –0.6 0 0.6
OUTPUT READING (µV)
1.2
1.8
2483 G08
0
10
30
40
20
TIME (HOURS)
50
60
2483 G09
2483f
6
LTC2483
U W
TYPICAL PERFOR A CE CHARACTERISTICS
RMS Noise
vs Input Differential Voltage
0.7
0.6
1.0
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
0.9
0.8
RMS Noise vs Temperature (TA)
0.8
0.4
–2.5 –2 –1.5 –1 –0.5 0 0.5 1 1.5 2
INPUT DIFFERENTIAL VOLTAGE (V)
0.7
0.6
–1
0
2
1
3
5
4
VCC = 5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
OFFSET ERROR (ppm OF VREF)
RMS NOISE (µV)
RMS NOISE (µV)
0.5
0.8
0.7
0.6
0.5
3.1
3.5
3.9 4.3
VCC (V)
4.7
5.1
0
1
2
3
VREF (V)
–0.1
–0.2
–1
–0.1
–0.2
75
90
2483 G16
0
1
3
2
VIN(CM) (V)
5
4
0.2
0.1
Offset Error vs VREF
0.3
REF+ = 2.5V
REF– = GND
VIN = 0V
VIN(CM) = GND
TA = 25°C
0
–0.1
VCC = 5V
REF– = GND
VIN = 0V
VIN(CM) = GND
TA = 25°C
0.2
0.1
0
–0.1
–0.2
–0.3
2.7
6
2483 G15
OFFSET ERROR (ppm OF VREF)
OFFSET ERROR (ppm OF VREF)
OFFSET ERROR (ppm OF VREF)
0.3
0
0 15 30 45 60
TEMPERATURE (°C)
0
Offset Error vs VCC
0.1
–0.3
–45 –30 –15
0.1
2483 G14
Offset Error vs Temperature
0.2
0.2
5
4
2483 G13
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
VCC = 5V
VREF = 5V
VIN = 0V
TA = 25°C
–0.3
0.4
5.5
90
Offset Error vs VIN(CM)
0.3
0.9
0.6
75
2483 G12
RMS Noise vs VREF
1.0
0.7
0 15 30 45 60
TEMPERATURE (°C)
2483 G11
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
TA = 25°C
0.4
2.7
0.4
–45 –30 –15
6
VIN(CM) (V)
0.8
0.3
0.6
0.4
2.5
RMS Noise vs VCC
0.9
0.7
0.5
2483 G10
1.0
0.8
0.5
0.5
VCC = 5V
VREF = 5V
VIN = 0V
VIN(CM) = GND
0.9
RMS NOISE (µV)
RMS NOISE (ppm OF VREF)
0.9
1.0
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
TA = 25°C
RMS NOISE (µV)
1.0
RMS Noise vs VIN(CM)
–0.2
3.1
3.5
3.9 4.3
VCC (V)
4.7
5.1
5.5
2483 G17
–0.3
0
1
2
3
VREF (V)
4
5
2483.G18
2483f
7
LTC2483
U W
TYPICAL PERFOR A CE CHARACTERISTICS
On-Chip Oscillator Frequency
vs VCC
On-Chip Oscillator Frequency
vs Temperature
310
310
304
302
VCC = 4.1V
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
300
–45 –30 –15
–40
306
304
300
75
90
–140
2.5
3.0
3.5
4.0
VCC (V)
4.5
5.0
–80
–60
–80
–100
–120
–120
0 20 40 60 80 100 120 140 160 180 200 220
FREQUENCY AT VCC (Hz)
–140
30600
30650
30700
30800
30750
FREQUENCY AT VCC (Hz)
Sleep Mode Current
vs Temperature
VCC = 5V
160
VCC = 2.7V
140
120
100
–45 –30 –15
0 15 30 45 60
TEMPERATURE (°C)
75
90
2483 G26
Conversion Current
vs Output Data Rate
2.0
500
1.8
450
SUPPLY CURRENT (µA)
1.6
1.4
VCC = 5V
1.0
0.8
0.6
180
2483 G25
2483 G24
1.2
1M
200
VCC = 4.1V DC ±0.7V
= 2.5V
V
–20 INREF
+ = GND
– = GND
IN
–40 TA = 25°C
–100
–140
10k 100k
1k
100
FREQUENCY AT VCC (Hz)
Conversion Current
vs Temperature
CONVERSION CURRENT (µA)
–60
10
2483 G23
0
VCC = 4.1V DC ±1.4V
VREF = 2.5V
IN+ = GND
IN– = GND
TA = 25°C
SLEEP MODE CURRENT (µA)
1
PSRR vs Frequency at VCC
REJECTION (dB)
REJECTION (dB)
–40
5.5
2483 G22
PSRR vs Frequency at VCC
–20
–80
–120
2483 G21
0
–60
–100
302
0 15 30 45 60
TEMPERATURE (°C)
VCC = 4.1V DC
VREF = 2.5V
IN+ = GND
IN– = GND
TA = 25°C
–20
REJECTION (dB)
FREQUENCY (kHz)
FREQUENCY (kHz)
306
0
VREF = 2.5V
VIN = 0V
VIN(CM) = GND
308
308
PSRR vs Frequency at VCC
VCC = 2.7V
VREF = VCC
IN+ = GND
IN– = GND
CA0/F0 = EXT OSC
TA = 25°C
400
350
VCC = 5V
300
VCC = 3V
250
200
0.4
150
0.2
0
–45 –30 –15
100
0 15 30 45 60
TEMPERATURE (°C)
75
90
2483 G27
0
10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2483 G28
2483f
8
LTC2483
U
U
U
PI FU CTIO S
REF+ (Pin 1), REF– (Pin 3): Differential Reference Input.
The voltage on these pins can have any value between GND
and VCC as long as the reference positive input, REF+, is
more positive than the reference negative input, REF –, by
at least 0.1V.
SDA (Pin 7): Serial Data Output Line of the I2C Interface.
In the transmitter mode (Read), the conversion result is
output through the SDA pin. It is an open-drain N-channel
driver and therefore an external pull-up resistor or current
source to VCC is needed.
VCC (Pin 2): Positive Supply Voltage. Bypass to GND
(Pin 8) with a 1µF tantalum capacitor in parallel with 0.1µF
ceramic capacitor as close to the part as possible.
GND (Pin 8): Ground. Connect this pin to a ground plane
through a low impedance connection.
IN+ (Pin 4), IN– (Pin 5): Differential Analog Input. The
voltage on these pins can have any value between
GND – 0.3V and VCC + 0.3V. Within these limits the
converter bipolar input range (VIN = IN+ – IN–) extends
from –0.5 • VREF to 0.5 • VREF. Outside this input range
the converter produces unique overrange and underrange
output codes.
SCL (Pin 6): Serial Clock Pin of the I2C Interface. The
LTC2483 can only act as a slave and the SCL pin only
accepts external serial clock. Data is shifted out the SDA
pin on the falling edges of the SCL clock.
CA1 (Pin 9): Chip Address Control Pin. The CA1 pin is
configured as a three state (LOW, HIGH, or Floating)
address control bit for the device I2C address.
CA0/F0 (Pin 10): Chip Address Control Pin/External Clock
Input Pin. When no transition is detected on the CA0/F0
pin, it is a two state (HIGH or Floating) address control bit
for the device I2C address. When the pin is driven by an
external clock signal with a frequency fEOSC of at least
10kHz, the converter uses this signal as its system clock
and the fundamental digital filter rejection null is located at
a frequency fEOSC/5120 and sets the Chip Address CA0
internally to a HIGH.
2483f
9
LTC2483
W
FU CTIO AL BLOCK DIAGRA
U
U
2
1
4
5
VCC
REF+
IN+
IN
SCL
REF+
IN+
I 2C
SERIAL
INTERFACE
3RD ORDER
∆Σ ADC
–
IN –
REF –
SDA
CA1
CA0/F0
6
7
9
10
AUTOCALIBRATION
AND CONTROL
REF–
3
GND
8
INTERNAL
OSCILLATOR
2483 FB
2483f
10
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
CONVERTER OPERATION
Converter Operation Cycle
The LTC2483 is a low power, ∆Σ analog-to-digital converter with an I2C interface. After power on reset, its
operation is made up of three states. The converter
operating cycle begins with the conversion, followed by
the low power sleep state and ends with the data output
(see Figure 1).
LTC2483 is addressed for a read operation, the device
begins outputting the conversion result under control of
the serial clock (SCL). There is no latency in the conversion result. The data output is 24 bits long and contains a
16-bit plus sign conversion result. This result is shifted
out on the SDA pin under the control of the SCL. Data is
updated on the falling edges of SCL allowing the user to
reliably latch data on the rising edge of SCL. A new
conversion is initiated at the conclusion of a data read
operation (read out all 24 bits).
POWER ON RESET
I2C INTERFACE
CONVERSION
SLEEP
NO
ACKNOWLEDGE
YES
DATA OUTPUT
NO
STOP
OR READ
24-BITS
YES
2483 F01
Figure 1. LTC2483 State Transition Diagram
Initially, the LTC2483 performs a conversion. Once the
conversion is complete, the device enters the sleep state.
While in this sleep state, power consumption is reduced
by two orders of magnitude. The part remains in the sleep
state as long as it is not addressed for a read operation.
The conversion result is held indefinitely in a static shift
register while the converter is in the sleep state.
The LTC2483 communicates through an I2C interface.
The I2C interface is a 2-wire open-drain interface supporting multiple devices and masters on a single bus. The
connected devices can only pull the bus wires LOW and
they never drive the bus HIGH. The bus wires are externally connected to a positive supply voltage via a currentsource or pull-up resistor. When the bus is free, both
lines are HIGH. Data on the I2C-bus can be transferred at
rates of up to 100kbit/s in the Standard-mode and up to
400kbit/s in the Fast-mode.
Each device on the I2C bus is recognized by a unique
address stored in that device and can operate as either a
transmitter or receiver, depending on the function of the
device. In addition to transmitters and receivers, devices
can also be considered as masters or slaves when performing data transfers. A master is the device which
initiates a data transfer on the bus and generates the clock
signals to permit that transfer. At the same time any device
addressed is considered a slave.
The LTC2483 can only be addressed as a slave. Once
addressed, it can transmit the last conversion result.
Therefore the serial clock line SCL is an input only and the
data line SDA is bidirectional (data out/address in). The
device supports the Standard-mode and the Fast-mode
for data transfer speeds up to 400kbit/s. Figure 2 shows
the definition of timing for Fast/Standard-mode devices
on the I2C-bus.
The device will not acknowledge an external request
during the conversion state. After a conversion is finished,
the device is ready to accept a read request. Once the
2483f
11
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
The START and STOP Conditions
Data Transferring
A START condition is generated by transitioning SDA from
HIGH to LOW while SCL is HIGH. The bus is considered to
be busy after the START condition. When the data transfer
is finished, a STOP condition is generated by transitioning
SDA from LOW to HIGH while SCL is HIGH. The bus is free
again a certain time after the STOP condition. START and
STOP conditions are always generated by the master.
After the START condition, the I2C bus is busy and data
transfer is set between a master and a slave. Data is
transferred over I2C in groups of nine bits (one byte)
followed by an acknowledge bit, therefore each group
takes nine SCL cycles. The transmitter releases the SDA
line during the acknowledge clock pulse and the receiver
issues an Acknowledge (ACK) by pulling SDA LOW or
leaves SDA HIGH to indicate a Not Acknowledge (NAK)
condition. Change of data state can only happen while SCL
is LOW.
When the bus is in use, it stays busy if a repeated START
(Sr) is generated instead of a STOP condition. The
repeated START (Sr) conditions are functionally identical
to the START (S).
SDA
tf
tLOW
tSU;DAT
tr
tr
tHD;STA
tSP
tr
tBUF
SCL
S
tHD;STA
tHD;DAT
tHIGH
tSU;STA
Sr
tSU;STO
P
S
2483 F02
Figure 2. Definition of Timing for F/S-Mode Devices on the I2C-Bus
2483f
12
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
LTC2483 Data Format
After a START condition, the master sends a 7-bit address
followed by a R/W bit. The bit R/W is 1 for a Read request
and 0 for a Write request. If the 7-bit address agrees with
an LTC2483’s address, that device is selected. When the
device is in the conversion state, it does not accept the
request and issues a Not-Acknowledge (NAK) by leaving
SDA HIGH. A write operation will also generate an NAK
signal. If the conversion is complete, it issues an acknowledge (ACK) by pulling SDA LOW.
The output register contains the last conversion result.
After each conversion is completed, the device automatically enters the sleep state where the supply current is
reduced to 1µA. When the LTC2483 is addressed for a
Read operation, it acknowledges (by pulling SDA LOW)
and acts as a transmitter. The master and receiver can read
up to three bytes from the LTC2483. After a complete Read
operation (3 bytes), the output register is emptied, a new
conversion is initiated, and a following Read request in the
same output phase will be NAKed. The LTC2483 output
data stream is 24 bits long, shifted out on the falling edges
of SCL. The first bit is the conversion result sign bit (SIG),
see Tables 1 and 2. This bit is HIGH if VIN ≥ 0. It is LOW if
VIN <0. The second bit is the most significant bit (MSB) of
the result. The first two bits (SIG and MSB) can be used to
indicate over range conditions. If both bits are HIGH, the
differential input voltage is above +FS and the following 16
bits are set to LOW to indicate an overrange condition. If
both bits are LOW, the input voltage is below –FS and the
following 16 bits are set to HIGH to indicate an underrange
condition. The function of these two bits is summarized in
Table 1. The next 16 bits contain the conversion results in
binary two’s complement format. The remaining six bits
are LOW.
Table 1. LTC2483 Status Bits
INPUT RANGE
BIT 23
SIG
BIT 22
MSB
VIN ≥ 0.5 • VREF
1
1
0V ≤ VIN < 0.5 • VREF
1
0
–0.5 • VREF ≤ VIN < 0V
0
1
VIN < – 0.5 • VREF
0
0
As long as the voltage on the IN+ and IN– pins is maintained within the – 0.3V to (VCC + 0.3V) absolute maximum
operating range, a conversion result is generated for any
differential input voltage VIN from –FS = –0.5 • VREF to +FS
= 0.5 • VREF. For differential input voltages greater than
+FS, the conversion result is clamped to the value corresponding to the +FS + 1LSB. For differential input voltages
below –FS, the conversion result is clamped to the value
corresponding to –FS – 1LSB.
Table 2. LTC2483 Output Data Format
DIFFERENTIAL INPUT VOLTAGE
VIN *
VIN* ≥ FS**
FS** – 1LSB
0.5 • FS**
0.5 • FS** – 1LSB
0
–1LSB
– 0.5 • FS**
– 0.5 • FS** – 1LSB
– FS**
VIN* < –FS**
BIT 23
SIG
1
1
1
1
1
0
0
0
0
0
BIT 22
MSB
1
0
0
0
0
1
1
1
1
0
BIT 21
BIT 20
BIT 19
…
BIT 6
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
…
…
…
…
…
…
…
…
…
…
0
1
0
1
0
1
0
1
0
1
*The differential input voltage VIN = IN+ – IN–. **The full-scale voltage FS = 0.5 • VREF.
2483f
13
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
Initiating a New Conversion
Easy Drive Input Current Cancellation
When the LTC2483 finishes a conversion, it automatically
enters the sleep state. Once in the sleep state, the device
is ready for a Read operation. After the device acknowledges a Read request, the device exits the sleep state and
enters the data output state. The data output state concludes and the LTC2483 starts a new conversion once a
STOP condition is issued by the master or all 24-bits of
data are read out of the device.
The LTC2483 combines a high precision delta-sigma ADC
with an automatic differential input current cancellation
front end. A proprietary front-end passive sampling
network transparently removes the differential input current. This enables external RC networks and high impedance sensors to directly interface to the LTC2483 without
external amplifiers. The remaining common mode input
current is eliminated by either balancing the differential
input impedances or setting the common mode input
equal to the common mode reference (see Automatic
Input Current Cancellation section). This unique architecture does not require on-chip buffers enabling input
signals to swing all the way to ground and up to VCC.
Furthermore, the cancellation does not interfere with the
transparent offset and full-scale auto-calibration and the
absolute accuracy (full scale + offset + linearity) is maintained even with external RC networks.
During the data read cycle, a stop command may be issued
by the master controller in order to start a new conversion
and abort the data transfer. This stop command must be
issued during the 9th clock cycle of a byte read when the
bus is free (the ACK/NAK cycle).
LTC2483 Address
The LTC2483 has two address pins, enabling one in 6
possible addresses, as shown in Table 3.
Conversion Clock
Table 3. LTC2483 Address Assignment
CA1
CA0/F0 *
Address
LOW
HIGH
001 01 00
LOW
Floating
001 01 01
Floating
HIGH
001 01 11
Floating
Floating
010 01 00
HIGH
HIGH
010 01 10
HIGH
Floating
010 01 11
* CA0/F0 is treated as HIGH when driven by a valid external clock.
Data Read
The data read operation sequence is shown in Figure 5.
When the conversion is finished, the device may be
addressed for a read operation. At the end of a read
operation, a new conversion begins. At the conclusion
of the conversion cycle, the next result may be read
using the method described above. If the conversion
cycle is not concluded and a valid address selects the
device, the LTC2483 generates a NAK signal indicating
the conversion cycle is in progress.
A major advantage the delta-sigma converter offers over
conventional type converters is an on-chip digital filter
(commonly implemented as a SINC or Comb filter). For high
resolution, low frequency applications, this filter is typically
designed to reject line frequencies of 50Hz and 60Hz plus
their harmonics. The filter rejection performance is directly
related to the accuracy of the converter system clock. The
LTC2483 incorporates a highly accurate on-chip oscillator.
This eliminates the need for external frequency setting components such as crystals or oscillators.
2483f
14
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
automatically detects the presence of an external clock
signal at the CA0/F0 pin and turns off the internal oscillator. The chip address for CA0 is internally set HIGH. The
frequency fEOSC of the external signal must be at least
10kHz to be detected. The external clock signal duty cycle
is not significant as long as the minimum and maximum
specifications for the high and low periods tHEO and tLEO
are observed.
Frequency Rejection Selection (CA0/F0)
The LTC2483 internal oscillator provides better than 87dB
normal mode rejection at line frequencies of 50Hz and
60Hz and all of their harmonics (up to the 255th) from
48Hz to 62.4Hz.
When a fundamental rejection frequency different from
50Hz/60Hz is required or when the converter must be
synchronized with an outside source, the LTC2483 can
operate with an external conversion clock. The converter
1 … 7
8
9
7-BIT
ADDRESS
R
1
2 …
SGN
MSB
ACK BY
LTC2483
START BY
MASTER
While operating with an external conversion clock of a
frequency fEOSC, the LTC2483 provides better than 110dB
9
1
2
D15
3
4
5
6
7
8
9
LSB
ACK BY
MASTER
NAK BY
MASTER
SLEEP
DATA OUTPUT
2483 F03
Figure 3. Timing Diagram for Reading from the LTC2483
S
R/W
7-BIT ADDRESS
ACK
SLEEP
DATA
Sr
DATA TRANSFERRING
P
DATA INPUT/OUTPUT
CONVERSION
2483 F04
Figure 4. The LTC2483 Conversion Sequence
S
7-BIT ADDRESS
R ACK
READ
P
S
7-BIT ADDRESS
R ACK
READ
P
CONVERSION
CONVERSION
SLEEP
DATA OUTPUT
SLEEP
DATA OUTPUT
CONVERSION
2483 F05
Figure 5. Consecutive Reading at the Same Configuration
2483f
15
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
normal mode rejection in a frequency range of fEOSC/5120
±4% and its harmonics. The normal mode rejection as a
function of the input frequency deviation from fEOSC/5120
is shown in Figure 6.
–80
NORMAL MODE REJECTION (dB)
–85
–90
Ease of Use
The LTC2483 data output has no latency, filter settling
delay or redundant data associated with the conversion
cycle. There is a one-to-one correspondence between the
conversion and the output data. Therefore, multiplexing
multiple analog voltages is easy.
The LTC2483 performs offset and full-scale calibrations
every conversion cycle. This calibration is transparent to the
user and has no effect on the cyclic operation described
above. The advantage of continuous calibration is extreme
stability of offset and full-scale readings with respect to
time, supply voltage change and temperature drift.
–95
–100
–105
–110
–115
–120
–125
–130
–135
–140
–12
–8
–4
0
4
8
12
DIFFERENTIAL INPUT SIGNAL FREQUENCY
DEVIATION FROM NOTCH FREQUENCY fEOSC/5120(%)
2483 F06
Figure 6. LTC2483 Normal Mode Rejection When
Using an External Oscillator
Power-Up Sequence
The LTC2483 automatically enters an internal reset state
when the power supply voltage VCC drops below approximately 2V. This feature guarantees the integrity of the conversion result.
Whenever an external clock is not present at the CA0/F0
pin, the converter automatically activates its internal oscillator and enters the Internal Conversion Clock mode.
CA0/F0 may be tied HIGH or left floating in order to set the
chip address. The LTC2483 operation will not be disturbed if the change of conversion clock source occurs
during the sleep state or during the data output state while
the converter uses an external serial clock. If the change
occurs during the conversion state, the result of the
conversion in progress may be outside specifications but
the following conversions will not be affected.
When the VCC voltage rises above this critical threshold,
the converter creates an internal power-on-reset (POR)
signal with a duration of approximately 4ms. The POR
signal clears all internal registers. Following the POR
signal, the LTC2483 starts a normal conversion cycle and
follows the succession of states described in Figure 1. The
first conversion result following POR is accurate within the
specifications of the device if the power supply voltage is
restored within the operating range (2.7V to 5.5V) before
the end of the POR time interval.
Table 4 summarizes the duration of the conversion state of
each state and the achievable output data rate as a function
of fEOSC.
Reference Voltage Range
The LTC2483 external reference voltage range is 0.1V to
VCC. The converter output noise is determined by the
Table 4. LTC2483 State Duration
STATE
CONVERSION
OPERATING MODE
DURATION
Internal Oscillator
50Hz/60Hz Rejection
147ms, Output Data Rate ≤ 6.8 Readings/s
External Oscillator
CA0/F0 = External Oscillator with Frequency
fEOSC Hz (fEOSC/5120 Rejection)
41036/fEOSCs, Output Data Rate ≤ fEOSC/41036 Readings/s
2483f
16
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
Input signals applied to IN+ and IN– pins may extend by
300mV below ground and above VCC. In order to limit any
fault current, resistors of up to 5k may be added in series
with the IN+ and IN– pins without affecting the performance of the devices. The effect of the series resistance on
the converter accuracy can be evaluated from the curves
presented in the Input Current/Reference Current sections. In addition, series resistors will introduce a temperature dependent offset error due to the input leakage
current. A 1nA input leakage current will develop a 1ppm
offset error on a 5k resistor if VREF = 5V. This error has a
very strong temperature dependency.
thermal noise of the front-end circuits, and as such, its
value in nanovolts is nearly constant with reference voltage. Since the transition noise (600nV) is much less than
the quantization noise (VREF/217), a decrease in the reference voltage will increase the converter resolution. A
reduced reference voltage will also improve the converter
performance when operated with an external conversion
clock (external FO signal) at substantially higher output
data rates (see the Output Data Rate section).
The reference input is differential. The differential reference input range (VREF = REF+ – REF–) is 100mV to VCC and
the common mode reference input range is 0V to VCC.
Input Voltage Range
Driving the Input and Reference
The analog input is truly differential with an absolute/
common mode range for the IN+ and IN– input pins
extending from GND – 0.3V to VCC + 0.3V. Outside
these limits, the ESD protection devices begin to turn on
and the errors due to input leakage current increase rapidly.
Within these limits, the LTC2483 converts the bipolar
differential input signal, VIN = IN+ – IN–, from – FS to +FS
where FS = 0.5 • VREF. Beyond this range, the converter
indicates the overrange or the underrange condition using
distinct output codes. Since the differential input current
cancellation does not rely on an on-chip buffer, current
cancellation and DC performance is maintained rail-to-rail.
The input and reference pins of the LTC2483 converter are
directly connected to a network of sampling capacitors.
Depending upon the relation between the differential input
voltage and the differential reference voltage, these capacitors are switching between these four pins transferring
small amounts of charge in the process. A simplified equivalent circuit is shown in Figure 7.
IREF+
VCC
RSW (TYP)
10k
ILEAK
+
( )
VREF
I IN+
ILEAK
I REF +
ILEAK
VIN+
RSW (TYP)
10k
CEQ
12pF
(TYP)
ILEAK
VCC
( )
= I IN –
AVG
=
AVG
=
VIN(CM) − VREF(CM)
0.5 • REQ
(
)
2
VIN 2
1.5 • VREF − VINCM + VREFCM
0.5 • VREF • DT 1.5VREF + VREF(CM) – VIN(CM)
VIN
–
−
−
≅
0.5 • REQ
0.5 • REQ
VREF • REQ
REQ
VREF • REQ
where:
⎛ REF + + REF – ⎞
+
–
VREFCM = ⎜
⎟ , VREF = REF − REF
2
⎠
⎝
VIN = IN+ − IN−
⎛ IN+ + IN− ⎞
VINCM = ⎜
⎟
2
⎠
⎝
RSW (TYP)
10k
ILEAK
VIN–
ILEAK
IREF–
AVG
( )
VCC
IIN+
IIN–
For a simple approximation, the source impedance RS
driving an analog input pin (IN+, IN–, REF+ or REF–) can be
considered to form, together with RSW and CEQ (see
Figure 7), a first order passive network with a time constant
τ = (RS + RSW) • CEQ. The converter is able to sample the
REQ = 2.98MΩ INTERNAL OSCILLATOR
(
VCC
)
REQ = 0.833 • 1012 / f EOSC EXTERNAL OSCILLATOR
ILEAK
VREF–
RSW (TYP)
10k
2483 F07
DT IS THE DENSITY OF A DIGITAL TRANSITION AT THE MODULATOR OUTPUT
WHERE REF– IS INTERNALLY TIED TO GND
ILEAK
SWITCHING FREQUENCY
fSW = 123kHz INTERNAL OSCILLATOR
fSW = 0.4 • fEOSC EXTERNAL OSCILLATOR
Figure 7. LTC2483 Equivalent Analog Input Circuit
2483f
17
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
Automatic Differential Input Current Cancellation
In applications where the sensor output impedance is low
(up to 10kΩ with no external bypass capacitor or up to
500Ω with 0.001µF bypass), complete settling of the input
occurs. In this case, no errors are introduced and direct
digitization of the sensor is possible.
For many applications, the sensor output impedance combined with external bypass capacitors produces RC time
constants much greater than the 580ns required for 1ppm
accuracy. For example, a 10kΩ bridge driving a 0.1µF
bypass capacitor has a time constant an order of magnitude greater than the required maximum. Historically,
settling issues were solved using buffers. These buffers
led to increased noise, reduced DC performance (Offset/
Drift), limited input/output swing (cannot digitize signals
near ground or VCC), added system cost and increased
power. The LTC2483 uses a proprietary switching algorithm that forces the average differential input current to
zero independent of external settling errors. This allows
accurate direct digitization of high impedance sensors
without the need of buffers (see Figures 8 to 10). Additional errors resulting from mismatched leakage currents
must also be taken into account.
The switching algorithm forces the average input current
on the positive input (IIN+) to be equal to the average input
current on the negative input (IIN–). Over the complete
conversion cycle, the average differential input current
(IIN+ – IIN–) is zero. While the differential input current is
VINCM + 0.5VIN
IN +
CPAR
≅ 20pF
CEXT
LTC2483
RSOURCE
VINCM – 0.5VIN
IN –
CPAR
≅ 20pF
CEXT
2483 F08
Figure 8. An RC Network at IN+ and IN–
80
+FS ERROR (ppm)
When using the internal oscillator, the LTC2483’s frontend switched-capacitor network is clocked at 123kHz
corresponding to an 8.1µs sampling period. Thus, for
settling errors of less than 1ppm, the driving source
impedance should be chosen such that τ ≤ 8.1µs/14 =
580ns. When an external oscillator of frequency fEOSC is
used, the sampling period is 2.5/fEOSC and, for a settling
error of less than 1ppm, τ ≤ 0.178/fEOSC.
RSOURCE
VCC = 5V
= 5V
60 VREF
VIN+ = 3.75V
– = 1.25V
V
IN
40
TA = 25°C
20
CEXT = 0pF
CEXT = 100pF
0
CEXT = 1nF, 0.1µF, 1µF
–20
–40
–60
–80
1
10
100
1k
RSOURCE (Ω)
10k
100k
2483 F09
Figure 9. +FS Error vs RSOURCE at IN+ and IN–
80
–FS ERROR (ppm)
input signal with better than 1ppm accuracy if the sampling
period is at least 14 times greater than the input circuit time
constant τ. The sampling process on the four input analog
pins is quasi-independent so each time constant should be
considered by itself and, under worst-case circumstances,
the errors may add.
VCC = 5V
= 5V
60 VREF
VIN+ = 1.25V
–
40 VIN = 3.75V
TA = 25°C
20
CEXT = 1nF, 0.1µF, 1µF
0
CEXT = 100pF
–20
CEXT = 0pF
–40
–60
–80
1
10
100
1k
RSOURCE (Ω)
10k
100k
2483 F10
Figure 10. –FS Error vs RSOURCE at IN+ and IN–
2483f
18
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
zero, the common mode input current (IIN++ IIN–)/2 is
proportional to the difference between the common mode
input voltage (VINCM) and the common mode reference
voltage (VREFCM).
In applications where the input common mode voltage is
equal to the reference common mode voltage, as in the
case of a balance bridge type application, both the differential and common mode input current are zero. The
accuracy of the converter is unaffected by settling errors.
Mismatches in source impedances between IN+ and IN–
also do not affect the accuracy.
In applications where the input common mode voltage is
constant but different from the reference common mode
voltage, the differential input current remains zero while
the common mode input current is proportional to the
difference between VINCM and VREFCM. For a reference
common mode of 2.5V and an input common mode of
1.5V, the common mode input current is approximately
0.74µA. This common mode input current has no effect on
the accuracy if the external source impedances tied to IN+
and IN– are matched. Mismatches in these source impedances lead to a fixed offset error but do not affect the
linearity or full-scale reading. A 1% mismatch in 1kΩ
source resistances leads to a 15ppm shift (74µV) in offset
voltage.
In applications where the common mode input voltage
varies as a function of input signal level (single-ended
input, RTDs, half bridges, current sensors, etc.), the
common mode input current varies proportionally with
input voltage. For the case of balanced input impedances,
the common mode input current effects are rejected by the
large CMRR of the LTC2483 leading to little degradation in
accuracy. Mismatches in source impedances lead to gain
errors proportional to the difference between the common
mode input voltage and the common mode reference
voltage. 1% mismatches in 1kΩ source resistances lead
to worst-case gain errors on the order of 15ppm or 1LSB
(for 1V differences in reference and input common mode
voltage). Table 5 summarizes the effects of mismatched
source impedance and differences in reference/input common mode voltages.
Table 5. Suggested Input Configuration for LTC2483
BALANCED INPUT
RESISTANCES
UNBALANCED INPUT
RESISTANCES
Constant
VIN(CM) – VREF(CM)
CEXT > 1nF at Both
IN+ and IN–. Can Take
Large Source Resistance
with Negligible Error
CEXT > 1nF at Both IN+
and IN–. Can Take Large
Source Resistance.
Unbalanced Resistance
Results in an Offset
Which Can be Calibrated
Varying
VIN(CM) – VREF(CM)
CEXT > 1nF at Both IN+
and IN–. Can Take Large
Source Resistance with
Negligible Error
Minimize IN+ and IN–
Capacitors and Avoid
Large Source Impedance
(< 5k Recommended)
The magnitude of the dynamic input current depends upon
the size of the very stable internal sampling capacitors and
upon the accuracy of the converter sampling clock. The
accuracy of the internal clock over the entire temperature
and power supply range is typically better than 0.5%. Such
a specification can also be easily achieved by an external
clock. When relatively stable resistors (50ppm/°C) are
used for the external source impedance seen by IN+ and
IN–, the expected drift of the dynamic current and offset
will be insignificant (about 1% of their respective values
over the entire temperature and voltage range). Even for
the most stringent applications, a one-time calibration
operation may be sufficient.
In addition to the input sampling charge, the input ESD
protection diodes have a temperature dependent leakage
current. This current, nominally 1nA (±10nA max), results
in a small offset shift. A 1k source resistance will create a
1µV typical and 10µV maximum offset voltage.
Reference Current
In a similar fashion, the LTC2483 samples the differential
reference pins REF+ and REF– transferring small amount
of charge to and from the external driving circuits thus
producing a dynamic reference current. This current does
not change the converter offset, but it may degrade the
gain and INL performance. The effect of this current can be
analyzed in two distinct situations.
For relatively small values of the external reference capacitors (CREF < 1nF), the voltage on the sampling capacitor
settles almost completely and relatively large values for the
source impedance result in only small errors. Such values
for CREF will deteriorate the converter offset and gain
2483f
19
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
performance without significant benefits of reference filtering and the user is advised to avoid them.
Larger values of reference capacitors (CREF > 1nF) may be
required as reference filters in certain configurations. Such
capacitors will average the reference sampling charge and
the external source resistance will see a quasi constant
reference differential impedance.
In the following discussion, it is assumed the input and
reference common mode are the same. For the internal
oscillator, the related difference resistance is 1.1MΩ and
10
90
VCC = 5V
VREF = 5V
VIN+ = 3.75V
VIN– = 1.25V
TA = 25°C
70
60
0
50
CREF = 0.01µF
CREF = 0.001µF
CREF = 100pF
CREF = 0pF
40
30
20
10
0
–10
0
10
CREF = 0.01µF
CREF = 0.001µF
CREF = 100pF
CREF = 0pF
–10
–FS ERROR (ppm)
80
+FS ERROR (ppm)
the resulting full-scale error is 0.46ppm for each ohm of
source resistance driving the REF+ and REF– pins. When
CA0/F0 is driven by an external oscillator with a frequency
fEOSC (external conversion clock operation), the typical
differential reference resistance is 0.30 • 1012/fEOSC Ω and
each ohm of source resistance driving the REF+ or REF– pins
will result in 1.67 • 10–6 • fEOSCppm gain error. The typical
+FS and –FS errors for various combinations of source
resistance seen by the REF+ or REF– pins and external
capacitance connected to that pin are shown in Figures
11-14.
1k
100
RSOURCE (Ω)
10k
100k
–20
–30
–40
–50
–60 VCC = 5V
VREF = 5V
–70 V + = 1.25V
IN
–
–80 VIN = 3.75V
TA = 25°C
–90
10
0
1k
100
RSOURCE (Ω)
10k
100k
2483 F12
2483 F11
Figure 11. +FS Error vs RSOURCE at REF+ or REF– (Small CREF)
400
+FS ERROR (ppm)
0
VCC = 5V
VREF = 5V
VIN+ = 3.75V
VIN– = 1.25V
TA = 25°C
CREF = 1µF, 10µF
–100
CREF = 0.1µF
300
200
CREF = 0.01µF
100
0
–FS ERROR (ppm)
500
Figure 12. –FS Error vs RSOURCE at REF+ or REF– (Small CREF)
CREF = 0.01µF
–200
CREF = 1µF, 10µF
–300
–400
0
200
600
400
RSOURCE (Ω)
800
1000
–500
CREF = 0.1µF
VCC = 5V
VREF = 5V
VIN+ = 1.25V
VIN– = 3.75V
TA = 25°C
0
200
600
400
RSOURCE (Ω)
2483 F13
Figure 13. +FS Error vs RSOURCE
at REF+
or REF–
(Large CREF)
800
1000
2483 F14
Figure 14. –FS Error vs RSOURCE
at REF+ or REF– (Large C
REF)
2483f
20
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
In addition to this gain error, the converter INL performance is degraded by the reference source impedance.
The INL is caused by the input dependent terms
–VIN2/(VREF • REQ) – (0.5 • VREF • DT)/REQ in the reference
pin current as expressed in Figure 7. When using internal
oscillator, every 100Ω of reference source resistance
translates into about 0.61ppm additional INL error. When
CA0/F0 is driven by an external oscillator with a frequency
fEOSC, every 100Ω of source resistance driving REF+ or
REF– translates into about 2.18 • 10–6 • fEOSCppm additional INL error. Figure 15 shows the typical INL error due
to the source resistance driving the REF+ or REF– pins
when large CREF values are used. The user is advised to
minimize the source impedance driving the REF+ and
REF– pins.
In applications where the reference and input common
mode voltages are different, extra errors are introduced.
For every 1V of the reference and input common mode
voltage difference (VREFCM – VINCM) and a 5V reference,
each Ohm of reference source resistance introduces an
extra (VREFCM – VINCM)/(VREF • REQ) full-scale gain error,
which is 0.067ppm when using internal oscillator. If an
external clock is used, the corresponding extra gain error
is 0.24 • 10–6 • fEOSCppm.
The magnitude of the dynamic reference current depends
upon the size of the very stable internal sampling capacitors and upon the accuracy of the converter sampling
clock. The accuracy of the internal clock over the entire
temperature and power supply range is typically better
than 0.5%. Such a specification can also be easily achieved
by an external clock. When relatively stable resistors
(50ppm/°C) are used for the external source impedance
seen by REF+ and REF–, the expected drift of the dynamic
current gain error will be insignificant (about 1% of its
value over the entire temperature and voltage range). Even
for the most stringent applications a one-time calibration
operation may be sufficient.
In addition to the reference sampling charge, the reference
pins ESD protection diodes have a temperature dependent
leakage current. This leakage current, nominally 1nA
(±10nA max), results in a small gain error. A 100Ω source
resistance will create a 0.05µV typical and 0.5µV maximum full-scale error.
INL (ppm OF VREF)
10
VCC = 5V
8 VREF = 5V
VIN(CM) = 2.5V
6 T = 25°C
A
4 CREF = 10µF
R = 1k
2
R = 500Ω
0
R = 100Ω
–2
–4
–6
–8
–10
– 0.5
– 0.3
0.1
– 0.1
VIN/VREF (V)
0.3
0.5
2483 F15
Figure 15. INL vs DIFFERENTIAL Input Voltage and
Reference Source Resistance for CREF > 1µF
2483f
21
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
Output Data Rate
When using its internal oscillator, the LTC2483 produces
up to 6.82sps with simultaneous 50Hz/60Hz rejection. The
actual output data rate will depend upon the length of the
sleep and data output phases which are controlled by the
user and which can be made insignificantly short. When
operated with an external conversion clock (CA0/F0 connected to an external oscillator), the LTC2483 output data
rate can be increased as desired. The duration of the
conversion phase is 41036/fEOSC. If fEOSC = 307.2kHz, the
converter notch is set at 60Hz.
An increase in fEOSC over the nominal 307.2kHz will
translate into a proportional increase in the maximum
3500
VIN(CM) = VREF(CM)
VCC = VREF = 5V
VIN = 0V
CA0/F0 = EXT CLOCK
40
First, a change in fEOSC will result in a proportional change
in the internal notch position and in a reduction of the
converter differential mode rejection at the power line
frequency. In many applications, the subsequent performance degradation can be substantially reduced by relying
upon the LTC2483’s exceptional common mode rejection
and by carefully eliminating common mode to differential
mode conversion sources in the input circuit. The user
should avoid single-ended input filters and should maintain a very high degree of matching and symmetry in the
circuits driving the IN+ and IN– pins.
3000
+FS ERROR (ppm OF VREF)
OFFSET ERROR (ppm OF VREF)
50
output data rate. The increase in output rate is nevertheless accompanied by three potential effects, which must
be carefully considered.
30
TA = 85°C
20
10
2500
TA = 85°C
2000
1500
TA = 25°C
1000
0
500
TA = 25°C
–10
0
VIN(CM) = VREF(CM)
VCC = VREF = 5V
CA0/F0 = EXT CLOCK
0
10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2483 F16
Figure 17. +FS Error vs Output Data Rate and Temperature
0
24
–500
22
–1000
20
TA = 25°C
TA = 85°C
RESOLUTION (BITS)
–FS ERROR (ppm OF VREF)
Figure 16. Offset Error vs Output Data Rate and Temperature
2483 F17
TA = 25°C
–1500
TA = 85°C
–2000
–2500
–3000
–3500
VIN(CM) = VREF(CM)
VCC = VREF = 5V
CA0/F0 = EXT CLOCK
18
16
14
12
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2483 F18
Figure 18. –FS Error vs Output Data Rate and Temperature
VIN(CM) = VREF(CM)
VCC = VREF = 5V
VIN = 0V
CA0/F0 = EXT CLOCK
RES = LOG 2 (VREF/NOISERMS)
10
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2483 F19
Figure 19. Resolution (NoiseRMS ≤ 1LSB)
vs Output Data Rate and Temperature
2483f
22
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
Second, the increase in clock frequency will increase
proportionally the amount of sampling charge transferred through the input and the reference pins. If large
external input and/or reference capacitors (CIN, CREF) are
used, the previous section provides formulae for evaluating the effect of the source resistance upon the converter
performance for any value of fEOSC. If small external input
and/or reference capacitors (CIN, CREF) are used, the
effect of the external source resistance upon the LTC2483
typical performance can be inferred from Figures 9, 10,
11 and 12 in which the horizontal axis is scaled by
307200/fEOSC.
Third, an increase in the frequency of the external oscillator
above 1MHz (a more than 3+ increase in the output data
rate) will start to decrease the effectiveness of the internal
autocalibration circuits. This will result in a progressive
degradation in the converter accuracy and linearity.
Typical measured performance curves for output data
rates up to 100 readings per second are shown in Figures 16 to 23. In order to obtain the highest possible level
of accuracy from this converter at output data rates above
20 readings per second, the user is advised to maximize
the power supply voltage used and to limit the maximum
ambient operating temperature. In certain circumstances,
a reduction of the differential reference voltage may
be beneficial.
20
RESOLUTION (BITS)
20
18
TA = 85°C
TA = 25°C
16
14
VIN(CM) = VREF(CM)
12 VCC = VREF = 5V
CA0/F0 = EXT CLOCK
RES = LOG 2 (VREF/INLMAX)
10
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
OFFSET ERROR (ppm OF VREF)
22
VIN(CM) = VREF(CM)
VIN = 0V
15 CA0/F0 = EXT CLOCK
TA = 25°C
10
VCC = VREF = 5V
5
0
–5
VCC = 5V, VREF = 2.5V
–10
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2483 F20
2483 F21
Figure 20. Resolution (INLMAX ≤ 1LSB)
vs Output Data Rate and Temperature
Figure 21. Offset Error vs Output
Data Rate and Reference Voltage
22
24
VCC = VREF = 5V
20
20
VCC = 5V, VREF = 2.5V
18
16
14 VIN(CM) = VREF(CM)
VIN = 0V
CA0/F0 = EXT CLOCK
12 T = 25°C
A
RES = LOG 2 (VREF/NOISERMS)
10
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2483 F22
Figure 22. Resolution (NoiseRMS ≤ 1LSB)
vs Output Data Rate and Reference Voltage
RESOLUTION (BITS)
RESOLUTION (BITS)
22
18
VCC = VREF = 5V
16
VCC = 5V, VREF = 2.5V
14
VIN(CM) = VREF(CM)
VIN = 0V
12 CA0/F0 = EXT CLOCK
TA = 25°C
RES = LOG 2 (VREF/INLMAX)
10
0 10 20 30 40 50 60 70 80 90 100
OUTPUT DATA RATE (READINGS/SEC)
2483 F23
Figure 23. Resolution (INLMAX ≤ 1LSB)
vs Output Data Rate and Reference Voltage
2483f
23
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
Input Bandwidth
The combined effect of the internal SINC4 digital filter and
of the analog and digital autocalibration circuits determines the LTC2483 input bandwidth. When the internal
oscillator is used, the 3dB input bandwidth is 3.3Hz. If an
external conversion clock generator of frequency fEOSC is
connected to the CA0/F0 pin, the 3dB input bandwidth is
11.8 • 10–6 • fEOSC.
Due to the complex filtering and calibration algorithms
utilized, the converter input bandwidth is not modeled
very accurately by a first order filter with the pole located
at the 3dB frequency. When the internal oscillator is
used, the shape of the LTC2483 input bandwidth is
shown in Figure 24. When an external oscillator of frequency fEOSC is used, the shape of the LTC2483 input
bandwidth can be derived from Figure 24, in which the
horizontal axis is scaled by f EOSC/279.2kHz.
The conversion noise (600nVRMS typical for VREF = 5V) can
be modeled by a white noise source connected to a noise
free converter. The noise spectral density is 47nV√Hz for
an infinite bandwidth source and 64nV√Hz for a single
0.5MHz pole source. From these numbers, it is clear that
particular attention must be given to the design of external
amplification circuits. Such circuits face the simultaneous
requirements of very low bandwidth (just a few Hz) in order
to reduce the output referred noise and relatively high
bandwidth (at least 500kHz) necessary to drive the input
switched-capacitor network. A possible solution is a high
gain, low bandwidth amplifier stage followed by a high
bandwidth unity-gain buffer.
When external amplifiers are driving the LTC2483, the
ADC input referred system noise calculation can be
simplified by Figure 25. The noise of an amplifier driving
the LTC2483 input pin can be modeled as a band limited
white noise source. Its bandwidth can be approximated
by the bandwidth of a single pole lowpass filter with a
corner frequency fi. The amplifier noise spectral density
is ni. From Figure 25, using fi as the x-axis selector, we
can find on the y-axis the noise equivalent bandwidth
freqi of the input driving amplifier. This bandwidth includes the band limiting effects of the ADC internal
calibration and filtering. The noise of the driving amplifier referred to the converter input and including all these
effects can be calculated as N = ni • √freqi. The total
system noise (referred to the LTC2483 input) can now be
obtained by summing as square root of sum of squares
the three ADC input referred noise sources: the LTC2483
internal noise, the noise of the IN+ driving amplifier and
the noise of the IN– driving amplifier.
If the CA0/F0 pin is driven by an external oscillator of
frequency fEOSC, Figure 25 can still be used for noise
calculation if the x-axis is scaled by fEOSC/307200. For
large values of the ratio fEOSC/307200, the Figure 25 plot
accuracy begins to decrease, but at the same time the
LTC2483 noise floor rises and the noise contribution of the
driving amplifiers lose significance.
Normal Mode Rejection and Antialiasing
One of the advantages delta-sigma ADCs offer over conventional ADCs is on-chip digital filtering. Combined with
a large oversampling ratio, the LTC2483 significantly
simplifies antialiasing filter requirements. Additionally,
the input current cancellation feature of the LTC2483
allows external lowpass filtering without degrading the DC
performance of the device.
The SINC4 digital filter provides greater than 120dB normal mode rejection at all frequencies except DC and
integer multiples of the modulator sampling frequency
(fS). The LTC2483’s autocalibration circuits further simplify the antialiasing requirements by additional normal
mode signal filtering both in the analog and digital domain.
Independent of the operating mode, fS = 256 • fN = 2048
• fOUTMAX where fN is the notch frequency and fOUTMAX is
the maximum output data rate. In the internal oscillator
mode, fS = 13960Hz. In the external oscillator mode, fS =
fEOSC/20. The performance of the normal mode rejection
is shown in Figures 26 and 27.
The regions of low rejection occurring at integer multiples
of fS have a very narrow bandwidth. Magnified details of
the normal mode rejection curves are shown in Figure 28
(rejection near DC) and Figure 29 (rejection at fS = 256fN)
where fN represents the notch frequency. These curves
have been derived for the external oscillator mode but they
can be used in all operating modes by appropriately
selecting the fN value.
2483f
24
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
100
–1
60Hz fEOSC = 307.2kHz
–2
50Hz fEOSC = 256kHz
–3
–4
INTERNAL
OSCILLATOR
–5
–6
INPUT REFERRED NOISE
EQUIVALENT BANDWIDTH (Hz)
INPUT SIGNAL ATTENUATION (dB)
0
10
1
0.1
0.1
1
3
4
0
5
2
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
2483 F24
Figure 25. Input Refered Noise Equivalent Bandwidth
of an Input Connected White Noise Source
0
0
–10
–10
INPUT NORMAL MODE REJECTION (dB)
INPUT NORMAL MODE REJECTION (dB)
Figure 24. Input Signal Using the Internal Oscillator
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
0 fS 2fS 3fS 4fS 5fS 6fS 7fS 8fS 9fS 10fS11fS12fS
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
2483 F26
INPUT NORMAL MODE REJECTION (dB)
0
fN = fEOSC/5120
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
0
fN
2fN 3fN 4fN 5fN 6fN 7fN
INPUT SIGNAL FREQUENCY (Hz)
8fN
2483 F28
Figure 28. Input Normal Mode Rejection at DC
0 fS 2fS 3fS 4fS 5fS 6fS 7fS 8fS 9fS 10fS
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
2483 F27
Figure 27. Input Normal Mode Rejection at DC
(Internal Oscillator)
0
INPUT NORMAL MODE REJECTION (dB)
Figure 26. Input Normal Mode Rejection,
External Oscillator (fEOSC = 256kHz)
50Hz Rejection
1
10 100 1k 10k 100k 1M
INPUT NOISE SOURCE SINGLE POLE
EQUIVALENT BANDWIDTH (Hz) 2483 F25
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
250fN 252fN 254fN 256fN 258fN 260fN 262fN
INPUT SIGNAL FREQUENCY (Hz)
2483 F29
Figure 29. Input Normal Mode Rejection at fs = 256fN
2483f
25
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
The user can expect to achieve this level of performance
using the internal oscillator as it is demonstrated by
Figures 30, 31 and 32. Typical measured values of the
normal mode rejection of the LTC2483 operating with an
external oscillator and a 60Hz notch setting are shown in
Figure 30 superimposed over the theoretical calculated
curve. Similarly, the measured normal rejection of the
LTC2483 for 50Hz rejection (fEOSC = 256kHz) and 50Hz/
60Hz rejection (internal oscillator) are shown in Figures 31
and 32.
As a result of these remarkable normal mode specifications, minimal (if any) antialias filtering is required in front
of the LTC2483. If passive RC components are placed in
front of the LTC2483, the input dynamic current should be
considered (see Input Current section). In this case, the
differential input current cancellation feature of the LTC2483
allows external RC networks without significant degradation in DC performance.
Traditional high order delta-sigma modulators, while providing very good linearity and resolution, suffer from
potential instabilities at large input signal levels. The proprietary architecture used for the LTC2483 third order modu-
lator resolves this problem and guarantees a predictable
stable behavior at input signal levels of up to 150% of full
scale. In many industrial applications, it is not uncommon
to have to measure microvolt level signals superimposed
on volt level perturbations and the LTC2483 is eminently
suited for such tasks. When the perturbation is differential,
the specification of interest is the normal mode rejection
for large input signal levels. With a reference voltage
VREF = 5V, the LTC2483 has a full-scale differential input
range of 5V peak-to-peak. Figures 33 and 34 show measurement results for the LTC2483 normal mode rejection
ratio with a 7.5V peak-to-peak (150% of full scale) input
signal superimposed over the more traditional normal
mode rejection ratio results obtained with a 5V peak-topeak (full scale) input signal. In Figure 33, the LTC2483
uses the external oscillator with the notch set at 60Hz and
in Figure 34 it uses the external oscillator with the notch set
at 50Hz. It is clear that the LTC2483 rejection performance
is maintained with no compromises in this extreme situation. When operating with large input signal levels, the user
must observe that such signals do not violate the device
absolute maximum ratings.
2483f
26
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
MEASURED DATA
CALCULATED DATA
–20
–40
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
– 60
–80
–100
–120
0
15
30
45
60
75
0
NORMAL MODE REJECTION (dB)
NORMAL MODE REJECTION (dB)
0
–20
–40
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
– 60
–80
–100
–120
90 105 120 135 150 165 180 195 210 225 240
INPUT FREQUENCY (Hz)
MEASURED DATA
CALCULATED DATA
0
12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200
INPUT FREQUENCY (Hz)
2483 F30
2483 F31
Figure 30. Input Normal Mode Rejection vs Input Frequency
with Input Perturbation of 100% Full Scale
(60Hz Notch fEOSC = 307.2kHz)
MEASURED DATA
CALCULATED DATA
–20
–40
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
VIN(P-P) = 5V
TA = 25°C
– 60
–80
–100
–120
0
20
40
60
80
100
120
140
INPUT FREQUENCY (Hz)
160
180
200
220
0
NORMAL MODE REJECTION (dB)
NORMAL MODE REJECTION (dB)
0
Figure 31. Input Normal Mode Rejection vs Input Frequency
with Input Perturbation of 100% Full Scale
(50Hz Notch fEOSC = 256kHz)
VIN(P-P) = 5V
VIN(P-P) = 7.5V
(150% OF FULL SCALE)
–20
VCC = 5V
VREF = 5V
VINCM = 2.5V
TA = 25°C
–40
– 60
–80
–100
–120
0
15
30
45
60
75
90 105 120 135 150 165 180 195 210 225 240
INPUT FREQUENCY (Hz)
2483 F33
2483 F32
Figure 32. Input Normal Mode Rejection vs Input Frequency
with Input Perturbation of 100% Full Scale (Internal Oscillator)
Figure 33. Measured Input Normal Mode Rejection vs
Input Frequency with Input Perturbation of 150% Full
Scale (60Hz Notch fEOSC = 307.2kHz)
NORMAL MODE REJECTION (dB)
0
VIN(P-P) = 5V
VIN(P-P) = 7.5V
(150% OF FULL SCALE)
–20
VCC = 5V
VREF = 5V
VIN(CM) = 2.5V
TA = 25°C
–40
– 60
–80
–100
–120
0
12.5 25 37.5 50 62.5 75 87.5 100 112.5 125 137.5 150 162.5 175 187.5 200
INPUT FREQUENCY (Hz)
2483 F34
Figure 34. Measured Input Normal Mode Rejection vs
Input Frequency with Input Perturbation of 150% Full
Scale (50Hz Notch fEOSC = 256kHz)
2483f
27
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
/*
LTC248X.h
Processor setup and
Lots of useful defines for configuring the LTC2481, LTC2483, and LTC2485.
*/
#include <16F73.h>
// Device
#use delay(clock=6000000)
// 6MHz clock
//#fuses NOWDT,HS, PUT, NOPROTECT, NOBROWNOUT
// Configuration fuses
#rom 0x2007={0x3F3A} // Equivalent and more reliable fuse config.
#use I2C(master, sda=PIN_C5, scl=PIN_C3, SLOW)// Set up i2c port
#include “PCM73A.h”
// Various defines
#include “lcd.c”
// LCD driver functions
#define READ
0x01
#define WRITE
0x00
#define LTC248XADDR 0b01001000
// bitwise OR with address for read or write
// The one and only LTC248X in this circuit,
// with both address lines floating.
// Useful defines for the LTC2481 and LTC2485 - OR them together to make the
// 8 bit config word.
// These do NOT apply to the LTC2483.
// Select gain - 1 to 256 (also depends on speed setting)
// Does NOT apply to LTC2485.
#define GAIN1 0b00000000
// G = 1
(SPD = 0), G = 1
#define GAIN2 0b00100000
// G = 4
(SPD = 0), G = 2
#define GAIN3 0b01000000
// G = 8
(SPD = 0), G = 4
#define GAIN4 0b01100000
// G = 16 (SPD = 0), G = 8
#define GAIN5 0b10000000
// G = 32 (SPD = 0), G = 16
#define GAIN6 0b10100000
// G = 64 (SPD = 0), G = 32
#define GAIN7 0b11000000
// G = 128 (SPD = 0), G = 64
#define GAIN8 0b11100000
// G = 256 (SPD = 0), G = 128
(SPD
(SPD
(SPD
(SPD
(SPD
(SPD
(SPD
(SPD
=
=
=
=
=
=
=
=
1)
1)
1)
1)
1)
1)
1)
1)
// Select ADC source - differential input or PTAT circuit
#define VIN
0b00000000
#define PTAT
0b00001000
// Select rejection frequency - 50, 55, or 60Hz
#define R50
0b00000010
#define R55
0b00000000
#define R60
0b00000100
// Select speed mode
#define SLOW
0b00000000 // slow output rate with autozero
#define FAST
0b00000001 // fast output rate with no autozero
2483f
28
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
/*
LTC2483.c
Basic voltmeter test program for LTC2483
Reads LTC2483, converts result to volts,
and prints voltage to a 2 line by 16 character LCD display.
Mark Thoren
Linear Technonlgy Corporation
June 23, 2005
Written for CCS PCM compiler, Version 3.182
*/
#include “LTC248X.h”
/*** read_LTC2483() ************************************************************
This is the funciton that actually does all the work of talking to the LTC2483.
Arguments:
addr - device address
Returns:
zero if conversion is in progress,
32 bit signed integer with lower 8 bits clear, 24 bit LTC2483
output word in the upper 24 bits. Data is left-justified for
compatibility with the 24 bit LTC2485.
the i2c_xxxx() functions do the following:
void i2c_start(void): generate an i2c start or repeat start condition
void i2c_stop(void): generate an i2c stop condition
char i2c_read(boolean): return 8 bit i2c data while generating an ack or nack
boolean i2c_write(): send 8 bit i2c data and return ack or nack from slave device
These functions are very compiler specific, and can use either a hardware i2c
port or software emulation of an i2c port. This example uses software emulation.
A good starting point when porting to other processors is to write your own
i2c functions. Note that each processor has its own way of configuring
the i2c port, and different compilers may or may not have built-in functions
for the i2c port.
When in doubt, you can always write a “bit bang” function for troubleshooting
purposes.
The “fourbytes” structure allows byte access to the 32 bit return value:
struct fourbytes // Define structure of four consecutive bytes
{
// To allow byte access to a 32 bit int or float.
int8 te0;
//
int8 te1;
// The make32() function in this compiler will
int8 te2;
// also work, but a union of 4 bytes and a 32 bit int
int8 te3;
// is probably more portable.
};
*******************************************************************************/
signed int32 read_LTC2483(char addr)
{
struct fourbytes // Define structure of four consecutive bytes
{
// To allow byte access to a 32 bit int or float.
int8 te0;
//
int8 te1;
// The make32() function in this compiler will
int8 te2;
// also work, but a union of 4 bytes and a 32 bit int
int8 te3;
// is probably more portable.
};
2483f
29
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
union
{
signed int32 bits32;
struct fourbytes by;
} adc_code;
//
//
//
//
//
adc_code.bits32
adc_code.by.te0
adc_code.by.te1
adc_code.by.te2
adc_code.by.te3
all 32 bits
byte 0
byte 1
byte 2
byte 3
// Start communication with LTC2483:
i2c_start();
if(i2c_write(addr | READ))// If no acknowledge, return zero
{
i2c_stop();
return 0;
}
adc_code.by.te3 = i2c_read();
adc_code.by.te2 = i2c_read();
adc_code.by.te1 = i2c_read();
adc_code.by.te0 = 0;
i2c_stop();
return adc_code.bits32;
} // End of read_LTC2483()
/*** initialize() **************************************************************
Basic hardware initialization of controller and LCD, send Hello message to LCD
*******************************************************************************/
void initialize(void)
{
// General initialization stuff.
setup_adc_ports(NO_ANALOGS);
setup_adc(ADC_OFF);
setup_counters(RTCC_INTERNAL,RTCC_DIV_1);
setup_timer_1(T1_DISABLED);
setup_timer_2(T2_DISABLED,0,1);
// This is the important part - configuring the SPI port
setup_spi(SPI_MASTER|SPI_L_TO_H|SPI_CLK_DIV_16|SPI_SS_DISABLED); // fast SPI clock
CKP = 0; // Set up clock edges - clock idles low, data changes on
CKE = 1; // falling edges, valid on rising edges.
lcd_init();
delay_ms(6);
printf(lcd_putc, “Hello!”);
delay_ms(500);
} // End of initialize()
// Initialize LCD
// Obligatory hello message
// for half a second
/*** main() ********************************************************************
Main program initializes microcontroller registers, then reads the LTC2483
repeatedly
*******************************************************************************/
void main()
{
signed int32 x;
// Integer result from LTC2481
float voltage;
// Variable for floating point math
int16 timeout;
initialize();
// Hardware initialization
while(1)
{
delay_ms(1);
// Pace the main loop to something more than 1 ms
// This is a basic error detection scheme. The LTC2483 will never take more than
// 149.9ms to complete a conversion in the 55Hz
// rejection mode.
2483f
30
LTC2483
U
W
U U
APPLICATIO S I FOR ATIO
// If read_LTC2483() does not return non-zero within this time period, something
// is wrong, such as an incorrect i2c address or bus conflict.
if((x = read_LTC2483(LTC248XADDR)) != 0)
{
// No timeout, everything is okay
timeout = 0;
// reset timer
x ^= 0x80000000;
// Invert MSB, result is 2’s complement
voltage = (float) x;
// convert to float
voltage = voltage * 5.0 / 2147483648.0;// Multiply by Vref, divide by 2^31
lcd_putc(‘\f’);
// Clear screen
lcd_gotoxy(1,1);
// Goto home position
printf(lcd_putc, “V %01.4f”, voltage); // Display voltage
}
else
{
++timeout;
}
if(timeout > 200)
{
timeout = 200;
// Prevent rollover
lcd_gotoxy(1,1);
printf(lcd_putc, “ERROR - TIMEOUT”);
delay_ms(500);
}
} // End of main loop
} // End of main()
U
PACKAGE DESCRIPTIO
DD Package
10-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1698)
R = 0.115
TYP
6
0.38 ± 0.10
10
0.675 ±0.05
3.50 ±0.05
1.65 ±0.05
2.15 ±0.05 (2 SIDES)
3.00 ±0.10
(4 SIDES)
PACKAGE
OUTLINE
1.65 ± 0.10
(2 SIDES)
PIN 1
TOP MARK
(SEE NOTE 6)
(DD10) DFN 1103
5
0.25 ± 0.05
0.200 REF
0.50
BSC
2.38 ±0.05
(2 SIDES)
1
0.75 ±0.05
0.00 – 0.05
0.25 ± 0.05
0.50 BSC
2.38 ±0.10
(2 SIDES)
BOTTOM VIEW—EXPOSED PAD
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2).
CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION
ASSIGNMENT
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SID
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
2483f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
31
LTC2483
U
TYPICAL APPLICATIO
5V
PIC16F73
C8
1µF
C7
0.1µF
ISOTHERMAL
R2
2k
4
TYPE K
THERMOCOUPLE
JACK
(OMEGA MPJ-K-F)
1.7k
1.7k
5
IN+
3 2
REF VCC
SCL
LTC2483
SDA
6
7
IN–
10
CA1 GND REF– CAO/FO
9
8
3
5V
D7
D6
2 × 16 CHARACTER
D5
LCD DISPLAY
D4
(OPTREX DMC162488
EN
OR SIMILAR)
RW
CONTRAST
GND D0 D1 D2 D3 RS
VCC
5V
1
3
R6
5k
2
5V
18
17
16
15
14
13
12
11
28
27
26
25
24
23
22
21
7
6
5
4
3
2
RC7
RC6
RC5
RC4
RC3
RC2
RC1
RC0
RB7
RB6
RB5
RB4
RB3
RB2
RB1
RB0
RA5
RA4
RA3
RA2
RA1
RA0
VDD
OSC1
OSC2
MCLR
VSS
VSS
20
5V
C6
0.1µF
9
Y1
6MHz
10
R1
1 10k
D1
BAT54
5V
9
19
2483 F35
R3
10k
CALIBRATE
2
1
DOWN
R4
10k
R5
10k
UP
Figure 35. Voltage Measurement Circuit
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1236A-5
Precision Bandgap Reference, 5V
0.05% Max Initial Accuracy, 5ppm/°C Drift
LT1460
Micropower Series Reference
0.075% Max Initial Accuracy, 10ppm/°C Max Drift
LT1790
Micropower SOT-23 Low Dropout Reference Family
0.05% Max Initial Accuracy, 10ppm/°C Max Drift
LTC2400
24-Bit, No Latency ∆Σ ADC in SO-8
0.3ppm Noise, 4ppm INL, 10ppm Total Unadjusted Error, 200µA
LTC2410
24-Bit, No Latency ∆Σ ADC with Differential Inputs
LTC2411/LTC2411-1 24-Bit, No Latency ∆Σ ADCs with Differential Inputs in MSOP
0.8µVRMS Noise, 2ppm INL
1.45µVRMS Noise, 4ppm INL,
Simultaneous 50Hz/60Hz Rejection (LTC2411-1)
LTC2413
24-Bit, No Latency ∆Σ ADC with Differential Inputs
Simultaneous 50Hz/60Hz Rejection, 800nVRMS Noise
LTC2415/
LTC2415-1
24-Bit, No Latency ∆Σ ADCs with 15Hz Output Rate
Pin Compatible with the LTC2410
LTC2414/LTC2418
8-/16-Channel 24-Bit, No Latency ∆Σ ADCs
0.2ppm Noise, 2ppm INL, 3ppm Total Unadjusted Errors 200µA
LTC2440
High Speed, Low Noise 24-Bit ∆Σ ADC
3.5kHz Output Rate, 200nV Noise, 24.6 ENOBs
LTC2480
16-Bit ∆Σ ADC with Easy Drive Inputs, 600nV Noise,
Programmable Gain, and Temperature Sensor
Pin Compatible with LTC2482/LTC2484
LTC2481
16-Bit ∆Σ ADC with Easy Drive Inputs, 600nV Noise,
I2C Interface, Programmable Gain, and Temperature Sensor
Pin Compatible with LTC2483/LTC2485
LTC2482
16-Bit ∆Σ ADC with Easy Drive Inputs
Pin Compatible with LTC2480/LTC2484
LTC2484
24-Bit ∆Σ ADC with Easy Drive Inputs
Pin Compatible with LTC2480/LTC2482
LTC2485
24-Bit ∆Σ ADC with Easy Drive Inputs, I2C Interface and
Temperature Sensor
Pin Compatible with LTC2481/LTC2483
2483f
32
Linear Technology Corporation
LT/LWI/TP 0805 500 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507 ● www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2005