Product specification Doc.-No.: For internal use only Revision: R2 OT DMX 3x1 RGB DIM Page: 1/2 1. General information 1.1 Product identification 1.2 Nominal range voltage of LED module 1.3 Type (independent converter, built-in converter with or without case etc.) 1.4 Protection class 1.5 Single ended / double ended 1.6 Weight 1.7 Max. Power losses OT DMX 3x1 RGB DIM 0---24 VDC Luminaire integration / case with terminals II Double ended 240 g. 1.5W 2. Supply input requirements 2.1 Nominal voltage range 2.2 Voltage range max. 2.3 Current max. 2.4 Incorrect connection 10,5 – 24 VDC (SELV or SELV equiv.) 8.5– 25 VDC (<30V without destruction) 3 A (1A per channel) No destruction of the device; 3. Control input requirements 3.1 Protocol specification 3.2 Electrical specification 3.3 Galvanic separation 3.4 Incorrect connection (polarity change) 3.5 Maximum voltage range without destruction 3.6 Channel assignment 3.7 Internal line termination USITT DMX-512A, DMX512 (DIN 56930-2) ANSI/TIA/EIA-485-A-1998 No, SELV required (acc. to EIA-485) No destruction of the device -7 – +12VDC Binary code, 10 bit dipswitch None 3.8 DMX Address 1-512 4. Output ( LED module ) requirements 4.1 Dimming mode 4.2 Working frequency 4.3 Audible noise: operating 4.4 Dimming range 4.5 Dimming curve 4.6 Maximum rated output current 4.7 Rated output power 4.8 Open circuit proof 4.9 Overload protection 4.10 Automatic restart after overload 4.11 Short circuit protection 4.12 Automatic restart after short circuit 4.13 Max. cable length between unit and module PWM ≥ 500 Hz < 20 dBA 0 - 100 % per channel EN 60929:2004 E.4.3.7 3*1A, 3*(0–10W)@10,5VDC 3*(0–24W)@24VDC Yes Yes Yes Yes Yes 10m 5. Temperatures and life expectation 5.1 Min. ambient temperature 5.2 Max. ambient temperature, ta 5.3 tc value 5.4 Overtemperature protection 5.5 Automatic restart after overtemperature 5.6 Lifetime, tc not exceeded, max. 10% failure -20 °C 50 °C 60 °C Yes Yes 30.000 hours EC LMS D EC LMS M LS-APR : Product specification Doc.-No.: For internal use only Revision: R2 OT DMX 3x1 RGB DIM 6. Installation, wiring and case 6.1 Dimensions 6.2 Terminals 6.3 Connector assignment Page: 2/2 80 mm x 40 mm x 22 mm Push-In wire input(Signal):D+,Dpower input: anode, Gnd 3 x common anode, R, G, B 1 0.75 mm2 to 1 mm2 White 0.75 mm2 to 1 mm2 4 (Red, Green, Blue, common anode) 0.75 mm2 to 1 mm2 Plastic No No 75mm. Class II OSRAM standard None 6.4 Number of supply input terminal pair 6.5 Supply input wire cross section 6.6 Colour 6.7 Control input wire cross section 6.8 Number of output (LED module) terminals 6.9 Output (LED module) wire cross section 6.10 Material of the case 6.11 Strain relief 6.12 Terminals covers 6.13 Mounting hole distance 6.14 Built in luminaires of class I/II 6.15 Labelling 6.16 Bar code identification 7. Standards 7.1 General and safety requirements 7.3 Immunity 7.4 MM / F / FF compliance 7.5 Approvals IEC 61347, IEC 60598 UL 508 recognized EN 55015, CISPR 15 FCC 47 part 15 – consumer equipment IEC 61547 MM, F CE 8. Packaging 8.1 Immunity against vibration and shock 8.2 Labelling of package 8.3 Bar code identification of package OSRAM standard OSRAM standard OSRAM standard 7.2 RFI Drawing: EC LMS D EC LMS M LS-APR :