86BC Low Cost 316L Stainless Steel 16mm Diameter Package 0 - 100mV Output Gage and Absolute Wide Compensated Temperature Range DESCRIPTION The 86BC is a 16mm small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless steel housing. The 86BC is designed with o-ring mounting for easy integration into industrial applications. The 86BC is a low cost unit designed without a header for applications where compatibility with corrosive media is required. The sensing package utilizes silicon oil to transfer pressure from the 316L stainless steel diaphragm to the sensing element. A ceramic substrate is attached to the package that contains laser-trimmed resistors for temperature compensation and offset correction. An additional laser trimmed resistor is included which can be used to adjust an external differential amplifier and provide span interchangeability to within ±1%. Please refer to the 86 uncompensated and constant voltage datasheets for more information on different features of the 86. FEATURES APPLICATIONS O-Ring Mount -40ºC to +105ºC Operating Temperature 1.0% Interchangeable Span (provided by gain set resistor) Solid State Reliability ±0.3% Pressure Non Linearity Medical Instruments Process Control Fresh & Waste Water Measurements Partial Vacuum Gas Measurement Pressure Transmitters Tank Level Systems (RV & Industrial) STANDARD RANGES Range (psi) Gage Range (Bar) Absolute 0 to 015 0 to 001 0 to 030 0 to 002 0 to 050 0 to 004 0 to 100 0 to 007 0 to 012 0 to 018 0 to 028 0 to 300 86BC www.meas-spec.com 1/4 April 2015 86BC PERFORMANCE SPECIFICATIONS Supply Current: 1.5mA Ambient Temperature: 25°C (unless otherwise specified) PARAMETERS MIN TYP MAX UNITS NOTES Span 75 100 150 mV 1, 2 -1 0 Zero Pressure Output, Offset +1 mV 2 Pressure Non-Linearity -0.3 0.3 %Span 3 Pressure Hysteresis -0.2 0.2 %Span Repeatability ±0.02 3.5 %Span kΩ Input Resistance 2.0 Output Resistance 3.0 25.0 kΩ Temperature Error – Span -1.0 1.0 %Span 4 Temperature Error – Zero -1.0 1.0 %Span 4 Thermal Hysteresis – Span -0.25 ±0.05 0.25 %Span 4 Thermal Hysteresis – Offset -0.25 ±0.05 0.25 %Span 4 Long Term Stability – Span ±0.10 Long Term Stability – Offset ±0.10 Supply Current 0.5 1.5 5.8 %Span/Year %Span/Year mA 5 Output Load Resistance 5 MΩ 6 Insulation Resistance (50Vdc) 50 MΩ 7 Output Noise (10Hz to 1kHz) 1.0 Response Time (10% to 90%) 0.1 2.0 uV p-p ms Pressure Overload 2X Rated 8 Pressure Burst 3X Rated 9 Compensated Temperature -20 +85 °C 10 Operating Temperature -40 +105 ºC 10 Storage Temperature -50 +105 ºC 10 Media – Pressure Port Liquids and Gases compatible with 316/316L Stainless Steel Notes 1. For amplified output circuits, 3.012V ±1% interchangeability with gain set resistor. See application schematic. 2. Measured at vacuum for absolute (A), ambient for gage (G). 3. Best fit straight line. 4. Over the compensated temperature range with respect to 25°C. 5. Guarantees output/input ratiometricity. 6. Load resistance to reduce measurement errors due to output loading. 7. Between case and sensing element. 8. 2X or 500psi, whichever is less. The maximum pressure that can be applied without changing the transducer’s performance or accuracy. 9. 3X or 600psi, whichever is less. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer. 10. Maximum temperature range for product with standard cable and connector is -20°C to +105°C. Additional Notes 11. Direct mechanical contact with diaphragm is prohibited. Diaphragm surface must remain free of defects (scratches, punctures, dents, fingerprints, etc.) for device to operate properly. Caution is advised when handling parts with exposed diaphragms. Use protective cap whenever devices are not in use. 12. Standard gage units are not recommended for vacuum applications. 86BC www.meas-spec.com 2/4 April 2015 86BC DIMENSIONS 86BC www.meas-spec.com 3/4 April 2015 86BC APPLICATION SCHEMATIC ORDERING INFORMATION 86BC - 100PG - C Model - Pressure Type and Range - Electrical 86BC - - P = Solder Pads R = Ribbon Cable C = Cable w/ Connector 015PG 030PG 050PG 100PG 300PG 001BA 002BA 004BA 007BA 012BA 018BA 028BA NORTH AMERICA EUROPE Measurement Specialties 45738 Northport Loop West Fremont, CA 94538 Tel: 1-800-767-1888 Fax: 1-510-498-1578 Sales: [email protected] Measurement Specialties (Europe), Ltd. 26 Rue des Dames 78340 Les Clayes-sous-Bois, France Tel: +33 (0) 130 79 33 00 Fax: +33 (0) 134 81 03 59 Sales: [email protected] ASIA Measurement Specialties (China), Ltd. No. 26 Langshan Road Shenzhen High-Tech Park (North) Nanshan District, Shenzhen 518057 China Tel: +86 755 3330 5088 Fax: +86 755 3330 5099 Sales: [email protected] The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assum ed for inaccuracies. Furthermore, this information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. Measurement Specialties, Inc. reserves the right to make changes without further notice to any product herein. Measurement Specialties, Inc. makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor does Measurement Specialties, Inc. assume any liability arising out of the application or use of any product or circuit and specif ically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application by customer’s technical experts. Measurement Specialties, Inc. does not convey any license under its patent rights nor the rights of others. 86BC www.meas-spec.com 4/4 April 2015