PDF Data Sheet Rev. G

Low Distortion,
Differential ADC Driver
AD8138
Data Sheet
PIN CONFIGURATION
–IN 1
8
+IN
VOCM 2
7
NC
V+ 3
+OUT 4
AD8138
6
V–
5
–OUT
NC = NO CONNECT
Figure 1.
TYPICAL APPLICATION CIRCUIT
5V
5V
499Ω
VIN
499Ω
+
VOCM
499Ω
AIN
AIN
–
AVDD
DVDD
DIGITAL
OUTPUTS
ADC
AD8138
AVSS
VREF
01073-002
Easy to use, single-ended-to-differential conversion
Adjustable output common-mode voltage
Externally adjustable gain
Low harmonic distortion
−94 dBc SFDR at 5 MHz
−85 dBc SFDR at 20 MHz
−3 dB bandwidth of 320 MHz, G = +1
Fast settling to 0.01% of 16 ns
Slew rate 1150 V/µs
Fast overdrive recovery of 4 ns
Low input voltage noise of 5 nV/√Hz
1 mV typical offset voltage
Wide supply range +3 V to ±5 V
Low power 90 mW on 5 V
0.1 dB gain flatness to 40 MHz
Available in 8-Lead SOIC and MSOP packages
01073-001
FEATURES
499Ω
Figure 2.
APPLICATIONS
ADC drivers
Single-ended-to-differential converters
IF and baseband gain blocks
Differential buffers
Line drivers
GENERAL DESCRIPTION
The AD8138 is a major advancement over op amps for
differential signal processing. The AD8138 can be used as a
single-ended-to-differential amplifier or as a differential-todifferential amplifier. The AD8138 is as easy to use as an op
amp and greatly simplifies differential signal amplification and
driving. Manufactured on the proprietary ADI XFCB bipolar
process, the AD8138 has a −3 dB bandwidth of 320 MHz and
delivers a differential signal with the lowest harmonic distortion
available in a differential amplifier. The AD8138 has a unique
internal feedback feature that provides balanced output gain
and phase matching, suppressing even order harmonics. The
internal feedback circuit also minimizes any gain error that
would be associated with the mismatches in the external gain
setting resistors.
The differential output of the AD8138 helps balance the input
to differential ADCs, maximizing the performance of the ADC.
Rev. G
The AD8138 eliminates the need for a transformer with high
performance ADCs, preserving the low frequency and dc information. The common-mode level of the differential output is
adjustable by a voltage on the VOCM pin, easily level-shifting the
input signals for driving single-supply ADCs. Fast overload
recovery preserves sampling accuracy.
The AD8138 distortion performance makes it an ideal ADC
driver for communication systems, with distortion performance
good enough to drive state-of-the-art 10-bit to 16-bit converters
at high frequencies. The high bandwidth and IP3 of the
AD8138 also make it appropriate for use as a gain block in IF
and baseband signal chains. The AD8138 offset and dynamic
performance makes it well suited for a wide variety of signal
processing and data acquisition applications.
The AD8138 is available in both SOIC and MSOP packages for
operation over −40°C to +85°C temperatures.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©1999–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD8138
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1 Definition of Terms .................................................................... 16 Applications ....................................................................................... 1 Theory of Operation ...................................................................... 17 Pin Configuration ............................................................................. 1 Analyzing an Application Circuit ............................................ 17 Typical Application Circuit ............................................................. 1 Setting the Closed-Loop Gain .................................................. 17 General Description ......................................................................... 1 Estimating the Output Noise Voltage ...................................... 17 Revision History ............................................................................... 2 The Impact of Mismatches in the Feedback Networks ......... 18 Specifications..................................................................................... 3 Calculating the Input Impedance of an Application ............. 18 ±DIN to ±OUT Specifications...................................................... 3 Input Common-Mode Voltage Range in Single-Supply
Applications ................................................................................ 18 VOCM to ±OUT Specifications ..................................................... 4 ±DIN to ±OUT Specifications...................................................... 5 VOCM to ±OUT Specifications ..................................................... 6 Absolute Maximum Ratings............................................................ 7 Thermal Resistance ...................................................................... 7 ESD Caution .................................................................................. 7 Pin Configuration and Function Descriptions ............................. 8 Typical Performance Characteristics ............................................. 9 Test Circuits ..................................................................................... 15 Setting the Output Common-Mode Voltage .......................... 18 Driving a Capacitive Load......................................................... 18 Layout, Grounding, and Bypassing .............................................. 19 Balanced Transformer Driver ....................................................... 20 High Performance ADC Driving ................................................. 21 3 V Operation ................................................................................. 22 Outline Dimensions ....................................................................... 23 Ordering Guide .......................................................................... 23 Operational Description ................................................................ 16 REVISION HISTORY
3/16—Rev. F to Rev. G
Changes to Setting the Closed-Loop Gain Section .................... 17
Changes to Figure 46 ...................................................................... 21
Changes to Figure 47 ...................................................................... 22
1/06—Rev. E to Rev. F
Changes to Features.......................................................................... 1
Added Thermal Resistance Section and Maximum Power
Dissipation Section ........................................................................... 7
Changes to Balanced Transformer Driver Section..................... 20
Changes to Ordering Guide .......................................................... 23
3/03—Rev. D to Rev. E
Changes to Specifications ................................................................ 2
Changes to Ordering Guide ............................................................ 4
Changes to TPC 16 ........................................................................... 6
Changes to Table I ............................................................................ 9
Added New Paragraph after Table I ............................................. 10
Updated Outline Dimensions ....................................................... 14
7/02—Rev. C to Rev. D
Addition of TPC 35 and TPC 36 .....................................................8
6/01—Rev. B to Rev. C
Edits to Specifications ......................................................................2
Edits to Ordering Guide ...................................................................4
12/00—Rev. A to Rev. B
9/99—Rev. 0 to Rev. A
3/99—Rev. 0: Initial Version
Rev. G | Page 2 of 24
Data Sheet
AD8138
SPECIFICATIONS
±DIN TO ±OUT SPECIFICATIONS
At 25°C, VS = ±5 V, VOCM = 0, G = +1, RL, dm = 500 Ω, unless otherwise noted. Refer to Figure 39 for test setup and label descriptions. All
specifications refer to single-ended input and differential outputs, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
Settling Time
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE 1
Second Harmonic
Third Harmonic
IMD
IP3
Voltage Noise (RTI)
Input Current Noise
INPUT CHARACTERISTICS
Offset Voltage
Conditions
Min
Typ
VOUT = 0.5 V p-p, CF = 0 pF
VOUT = 0.5 V p-p, CF = 1 pF
VOUT = 0.5 V p-p, CF = 0 pF
VOUT = 2 V p-p, CF = 0 pF
VOUT = 2 V p-p, CF = 0 pF
0.01%, VOUT = 2 V p-p, CF = 1 pF
VIN = 5 V to 0 V step, G = +2
290
320
225
30
265
1150
16
4
MHz
MHz
MHz
MHz
V/µs
ns
ns
−94
−87
−62
−114
−85
−57
−77
37
5
2
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBm
nV/√Hz
pA/√Hz
VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 70 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 70 MHz, RL, dm = 800 Ω
20 MHz
20 MHz
f = 100 kHz to 40 MHz
f = 100 kHz to 40 MHz
VOS, dm = VOUT, dm/2; VDIN+ = VDIN− = VOCM = 0 V
TMIN to TMAX variation
Input Bias Current
Input Resistance
Input Capacitance
Input Common-Mode Voltage
CMRR
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current
Output Balance Error
1
TMIN to TMAX variation
Differential
Common mode
∆VOUT, dm/∆VIN, cm; ∆VIN, cm = ±1 V
Maximum ∆VOUT; single-ended output
∆VOUT, cm/∆VOUT, dm; ∆VOUT, dm = 1 V
−2.5
±1
±4
3.5
−0.01
6
3
1
−4.7 to +3.4
−77
7.75
95
−66
Harmonic distortion performance is equal or slightly worse with higher values of RL, dm. See Figure 17 and Figure 18 for more information.
Rev. G | Page 3 of 24
Max
+2.5
7
−70
Unit
mV
µV/°C
µA
µA/°C
MΩ
MΩ
pF
V
dB
V p-p
mA
dB
AD8138
Data Sheet
VOCM TO ±OUT SPECIFICATIONS
At 25°C, VS = ±5 V, VOCM = 0, G = +1, RL, dm = 500 Ω, unless otherwise noted. Refer to Figure 39 for test setup and label descriptions. All
specifications refer to single-ended input and differential outputs, unless otherwise noted.
Table 2.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Slew Rate
INPUT VOLTAGE NOISE (RTI)
DC PERFORMANCE
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Bias Current
VOCM CMRR
Gain
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
OPERATING TEMPERATURE RANGE
Conditions
Min
f = 0.1 MHz to 100 MHz
VOS, cm = VOUT, cm; VDIN+ = VDIN– = VOCM = 0 V
–3.5
∆VOUT, dm/∆VOCM; ∆VOCM = ±1 V
∆VOUT, cm/∆VOCM; ∆VOCM = ±1 V
0.9955
±1.4
18
TMIN to TMAX variation
∆VOUT, dm/∆VS; ∆VS = ±1 V
−40
Rev. G | Page 4 of 24
Typ
Max
Unit
250
330
17
MHz
V/µs
nV/√Hz
±3.8
200
±1
0.5
−75
1
V
kΩ
mV
µA
dB
V/V
20
40
−90
+3.5
1.0045
±5.5
23
−70
+85
V
mA
µA/°C
dB
°C
Data Sheet
AD8138
±DIN TO ±OUT SPECIFICATIONS
At 25°C, VS = 5 V, VOCM = 2.5 V, G = +1, RL, dm = 500 Ω, unless otherwise noted. Refer to Figure 39 for test setup and label descriptions. All
specifications refer to single-ended input and differential output, unless otherwise noted.
Table 3.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
Settling Time
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE 1
Second Harmonic
Third Harmonic
IMD
IP3
Voltage Noise (RTI)
Input Current Noise
INPUT CHARACTERISTICS
Offset Voltage
Conditions
Min
Typ
VOUT = 0.5 V p-p, CF = 0 pF
VOUT = 0.5 V p-p, CF = 1 pF
VOUT = 0.5 V p-p, CF = 0 pF
VOUT = 2 V p-p, CF = 0 pF
VOUT = 2 V p-p, CF = 0 pF
0.01%, VOUT = 2 V p-p, CF = 1 pF
VIN = 2.5 V to 0 V step, G = +2
280
310
225
29
265
950
16
4
MHz
MHz
MHz
MHz
V/µs
ns
ns
−90
−79
−60
−100
−82
−53
−74
35
5
2
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBm
nV/√Hz
pA/√Hz
VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 70 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 70 MHz, RL, dm = 800 Ω
20 MHz
20 MHz
f = 100 kHz to 40 MHz
f = 100 kHz to 40 MHz
VOS, dm = VOUT, dm/2; VDIN+ = VDIN– = VOCM = 0 V
TMIN to TMAX variation
Input Bias Current
Input Resistance
Input Capacitance
Input Common-Mode Voltage
CMRR
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current
Output Balance Error
1
TMIN to TMAX variation
Differential
Common mode
∆VOUT, dm/∆VIN, cm; ∆VIN, cm = 1 V
Maximum ∆VOUT; single-ended output
∆VOUT, cm/∆VOUT, dm; ∆VOUT, dm = 1 V
−2.5
±1
±4
3.5
−0.01
6
3
1
−0.3 to +3.2
−77
2.9
95
−65
Harmonic distortion performance is equal or slightly worse with higher values of RL, dm. See Figure 17 and Figure 18 for more information.
Rev. G | Page 5 of 24
Max
+2.5
7
−70
Unit
mV
µV/°C
µA
µA/°C
MΩ
MΩ
pF
V
dB
V p-p
mA
dB
AD8138
Data Sheet
VOCM TO ±OUT SPECIFICATIONS
At 25°C, VS = 5 V, VOCM = 2.5 V, G = +1, RL, dm = 500 Ω, unless otherwise noted. Refer to Figure 39 for test setup and label descriptions. All
specifications refer to single-ended input and differential output, unless otherwise noted.
Table 4.
Parameter
DYNAMIC PERFORMANCE
−3 dB Bandwidth
Slew Rate
INPUT VOLTAGE NOISE (RTI)
DC PERFORMANCE
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Bias Current
VOCM CMRR
Gain
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
OPERATING TEMPERATURE RANGE
Conditions
Min
f = 0.1 MHz to 100 MHz
VOS, cm = VOUT, cm; VDIN+ = VDIN– = VOCM = 0 V
−5
∆VOUT, dm/∆VOCM; ∆VOCM = 2.5 V ±1 V
∆VOUT, cm/∆VOCM; ∆VOCM = 2.5 V ±1 V
0.9968
2.7
15
TMIN to TMAX variation
∆VOUT, dm/∆VS; ∆VS = ± 1 V
−40
Rev. G | Page 6 of 24
Typ
Max
Unit
220
250
17
MHz
V/µs
nV/√Hz
1.0 to 3.8
100
±1
0.5
−70
1
V
kΩ
mV
µA
dB
V/V
20
40
−90
+5
1.0032
11
21
−70
+85
V
mA
µA/°C
dB
°C
Data Sheet
AD8138
ABSOLUTE MAXIMUM RATINGS
Table 5.
Ratings
±5.5 V
±VS
550 mW
−40°C to +85°C
−65°C to +150°C
300°C
150°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, θJA is
specified for the device soldered in a circuit board in still air.
Airflow reduces θJA. In addition, more metal directly in contact
with the package leads from metal traces through holes, ground,
and power planes reduces the θJA.
Figure 3 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the 8-lead SOIC
(121°C/W) and 8-lead MSOP (θJA = 145°C/W) packages on a
JEDEC standard 4-layer board. θJA values are approximations.
1.75
Table 6.
Package Type
8-Lead SOIC/4-Layer
8-Lead MSOP/4-Layer
θJA
121
145
Unit
°C/W
°C/W
Maximum Power Dissipation
The maximum safe power dissipation in the AD8138 packages
is limited by the associated rise in junction temperature (TJ) on
the die. At approximately 150°C, which is the glass transition
temperature, the plastic changes its properties. Even temporarily
exceeding this temperature limit can change the stresses that the
package exerts on the die, permanently shifting the parametric
performance of the AD8138. Exceeding a junction temperature
of 150°C for an extended period can result in changes in the
silicon devices, potentially causing failure.
1.50
1.25
1.00
SOIC
0.75
MSOP
0.50
0.25
0
–40 –30 –20 –10
0
10
20
30
40
50
60
70
80
90 100 110 120
AMBIENT TEMPERATURE (°C)
Figure 3. Maximum Power Dissipation vs. Temperature
ESD CAUTION
Rev. G | Page 7 of 24
01073-049
MAXIMUM POWER DISSIPATION (W)
Parameter
Supply Voltage
VOCM
Internal Power Dissipation
Operating Temperature Range
Storage Temperature Range
Lead Temperature (Soldering 10 sec)
Junction Temperature
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive for all outputs. The quiescent
power is the voltage between the supply pins (VS) times the
quiescent current (IS). The load current consists of the differential
and common-mode currents flowing to the load, as well as
currents flowing through the external feedback networks and
internal common-mode feedback loop. The internal resistor tap
used in the common-mode feedback loop places a negligible
differential load on the output. RMS voltages and currents
should be considered when dealing with ac signals.
AD8138
Data Sheet
–IN 1
8
+IN
VOCM 2
7
NC
V+ 3
6
V–
5
–OUT
+OUT 4
AD8138
NC = NO CONNECT
01073-004
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 4. Pin Configuration
Table 7. Pin Function Descriptions
Pin No.
1
2
Mnemonic
−IN
VOCM
3
4
5
6
7
8
V+
+OUT
−OUT
V−
NC
+IN
Description
Negative Input Summing Node.
Voltage applied to this pin sets the common-mode output voltage with a ratio of 1:1. For example,
1 V dc on VOCM sets the dc bias level on +OUT and −OUT to 1 V.
Positive Supply Voltage.
Positive Output. Note that the voltage at −DIN is inverted at +OUT (see Figure 42).
Negative Output. Note that the voltage at +DIN is inverted at −OUT (see Figure 42).
Negative Supply Voltage.
No Connect.
Positive Input Summing Node.
Rev. G | Page 8 of 24
Data Sheet
AD8138
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise noted, Gain = 1, RG = RF = RL, dm = 499 V, TA = 25°C; refer to Figure 39 for test setup.
6
6
VIN = 2V p-p
CF = 0pF
VIN = 0.2V p-p
CF = 0pF
3
3
VS = +5V
0
GAIN (dB)
VS = ±5V
–3
–6
0
VS = ±5V
–3
1
10
100
FREQUENCY (MHz)
1000
–9
01073-005
–9
1
Figure 5. Small Signal Frequency Response
10
100
FREQUENCY (MHz)
Figure 8. Large Signal Frequency Response
6
6
VS = ±5V
VIN = 0.2V p-p
VIN = 2V p-p
VS = ±5V
3
3
CF = 0pF
CF = 0pF
0
GAIN (dB)
GAIN (dB)
1000
01073-008
–6
CF = 1pF
–3
0
CF = 1pF
–3
–6
–6
100
10
FREQUENCY (MHz)
1
1000
–9
01073-006
–9
1
Figure 6. Small Signal Frequency Response
10
100
FREQUENCY (MHz)
1000
01073-009
GAIN (dB)
VS = +5V
Figure 9. Large Signal Frequency Response
0.5
30
VS = ±5V
VIN = 0.2V p-p
0.3
CF = 0pF
G = 10, RF = 4.99kΩ
20
VS = ±5V
CF = 0pF
VOUT, dm = 0.2V p-p
RG = 499Ω
GAIN (dB)
–0.1
10
G = 2, RF = 1kΩ
CF = 1pF
G = 1, RF = 499Ω
0
–0.5
1
10
FREQUENCY (MHz)
100
Figure 7. 0.1 dB Flatness vs. Frequency
–10
1
100
10
FREQUENCY (MHz)
1000
Figure 10. Small Signal Frequency Response for Various Gains
Rev. G | Page 9 of 24
01073-010
–0.3
01073-007
GAIN (dB)
G = 5, RF = 2.49kΩ
0.1
AD8138
Data Sheet
–50
–60
VOUT, dm = 2V p-p
RL = 800Ω
VS = ±5V
RL = 800Ω
–60
HD3 (F = 20MHz)
–70
HD2 (F = 20MHz)
DISTORTION (dBc)
DISTORTION (dBc)
–70
HD2 (VS = +5V)
–80
HD2 (VS = ±5V)
–90
–80
–90
HD2 (F = 5MHz)
–100
–100
HD3 (VS = +5V)
HD3 (F = 5MHz)
–110
–110
10
30
40
50
20
FUNDAMENTAL FREQUENCY (MHz)
60
70
–120
01073-011
0
0
Figure 11. Harmonic Distortion vs. Frequency
1
2
3
4
5
DIFFERENTIAL OUTPUT VOLTAGE (V p-p)
Figure 14. Harmonic Distortion vs. Differential Output Voltage
–60
–40
VOUT, dm = 4V p-p
RL = 800Ω
VS = 5V
RL = 800Ω
–50
–70
HD2 (F = 20MHz)
DISTORTION (dBc)
HD3 (VS = +5V)
–60
DISTORTION (dBc)
6
01073-014
HD3 (VS = ±5V)
–120
–70
HD2 (VS = +5V)
–80
HD2 (VS = ±5V)
–80
HD3 (F = 20MHz)
–90
HD2 (F = 5MHz)
–100
–90
HD3 (F = 5MHz)
–110
HD3 (VS = ±5V)
0
10
20
30
40
50
FUNDAMENTAL FREQUENCY (MHz)
60
70
–120
01073-012
–110
0
1
2
3
DIFFERENTIAL OUTPUT VOLTAGE (V p-p)
Figure 15. Harmonic Distortion vs. Differential Output Voltage
Figure 12. Harmonic Distortion vs. Frequency
–60
–30
VS = 3V
RL = 800Ω
VOUT, dm = 2V p-p
RL = 800Ω
FO = 20MHz
–70
DISTORTION (dBc)
–50
HD2 (VS = +5V)
–60
HD3 (VS = +5V)
–70
–80
HD3 (VS = ±5V)
–90
HD2 (VS = ±5V)
–80
–90
HD2 (F = 5MHz)
–4
–3
–2
0
1
VOCM DC OUTPUT (V)
–1
2
3
4
01073-013
–100
–100
HD3 (F = 20MHz)
HD2 (F = 20MHz)
–110
0.25
HD3 (F = 5MHz)
0.50
1.00
1.25
0.75
1.50
DIFFERENTIAL OUTPUT VOLTAGE (V p-p)
1.75
Figure 16. Harmonic Distortion vs. Differential Output Voltage
Figure 13. Harmonic Distortion vs. VOCM
Rev. G | Page 10 of 24
01073-016
–40
DISTORTION (dBc)
4
01073-015
–100
Data Sheet
AD8138
–60
45
RL = 800Ω
VS = 5V
VOUT, dm = 2V p-p
–70
INTERCEPT (dBm)
DISTORTION (dBc)
40
HD2 (F = 20MHz)
–80
HD3 (F = 20MHz)
–90
HD2 (F = 5MHz)
VS = ±5V
35
VS = +5V
30
–100
600
1000
RLOAD (Ω)
1400
25
01073-017
–110
200
1800
0
Figure 17. Harmonic Distortion vs. RLOAD
20
40
FREQUENCY (MHz)
60
Figure 20. Third-Order Intercept vs. Frequency
–60
VS = ±5V
VS = ±5V
VOUT, dm = 2V p-p
–70
VOUT, dm
HD3 (F = 20MHz)
VOUT–
–90
VOUT+
HD2 (F = 5MHz)
–100
V+DIN
HD3 (F = 5MHz)
–110
600
1000
RLOAD (Ω)
1400
5ns
01073-018
1V
–120
200
01073-021
DISTORTION (dBc)
HD2 (F = 20MHz)
–80
80
1800
Figure 18. Harmonic Distortion vs. RLOAD
Figure 21. Large Signal Transient Response
10
FC = 50MHz
VS = ±5V
CF = 0pF
VOUT, dm = 0.2V p-p
VS = ±5V
–10
CF = 1pF
–50
–90
40mV
–110
49.5
49.7
49.9
50.1
FREQUENCY (MHz)
50.3
50.5
5ns
Figure 19. Intermodulation Distortion
Figure 22. Small Signal Transient Response
Rev. G | Page 11 of 24
01073-022
–70
01073-019
POUT (dBm)
–30
01073-020
HD3 (F = 5MHz)
AD8138
Data Sheet
VOUT, dm = 2V p-p
CF = 0pF
VS = ±5V
VOUT, dm
VS = +5V
VS = ±5V
F = 20MHz
V+DIN = 8V p-p
G = 3 (RF = 1500)
5ns
4V
Figure 26. Output Overdrive
Figure 23. Large Signal Transient Response
VOUT, dm = 2V p-p
VS = ±5V
CF = 0pF
30ns
01073-026
400mV
01073-023
V+DIN
VS = ±5V
CF = 0pF
CL = 10pF
CL = 5pF
CF = 1pF
5ns
Figure 24. Large Signal Transient Response
400mV
2.5ns
01073-028
400mV
01073-024
CL = 20pF
Figure 27. Large Signal Transient Response for Various Cap Loads (See Figure 40)
–20
VS = ±5V
∆VOUT, dm/∆VIN, cm
VS = ±5V
CF = 1pF
200µV
–30
VOUT, dm
CMRR (dB)
–40
–50
–60
4ns
01073-025
1V
–80
1
10
100
FREQUENCY (MHz)
Figure 28. CMRR vs. Frequency
Figure 25. Settling Time
Rev. G | Page 12 of 24
1k
01073-029
–70
V+DIN
Data Sheet
AD8138
–20
5.0
–40
VS = ±5V
–50
–60
VS = +5V
–70
100
10
FREQUENCY (MHz)
1
1k
Figure 29. Output Balance Error vs. Frequency (See Figure 41)
2.5
VS = ±5V
VS = +5V
0
VS = +3V
–2.5
–5.0
–40
01073-031
BALANCE ERROR (dB)
–30
–20
0
20
40
TEMPERATURE (°C)
60
80
100
01073-034
DIFFERENTIAL OUTPUT OFFSET (mV)
VIN = 2V p-p
Figure 32. Output Referred Differential Offset Voltage vs. Temperature
–10
5
ΔVOUT, dm/ΔVS
–20
4
–PSRR
(VS = ±5V)
BIAS CURRENT (µA)
PSRR (dB)
–30
–40
–50
–60
+PSRR
(VS = +5V, 0V AND ±5V)
–70
VS = ±5V, +5V
3
VS = +3V
2
1
10
100
FREQUENCY (MHz)
1k
1
–40
01073-032
–90
Figure 30. PSRR vs. Frequency
–20
0
20
40
60
TEMPERATURE (°C)
80
100
01073-035
–80
Figure 33. Input Bias Current vs. Temperature
100
30
SINGLE-ENDED OUTPUT
SUPPLY CURRENT (mA)
10
VS = +5V
1
10
FREQUENCY (MHz)
VS = +5V
15
VS = +3V
100
5
–40
–20
0
60
20
40
TEMPERATURE (°C)
80
Figure 34. Supply Current vs. Temperature
Figure 31. Output Impedance vs. Frequency
Rev. G | Page 13 of 24
100
01073-036
0.1
1
VS = ±5V
20
10
VS = ±5V
01073-033
IMPEDANCE (Ω)
25
AD8138
Data Sheet
100
6
VS = +5V
–3
–9
1
10
100
FREQUENCY (MHz)
1k
10
1.1pA/ Hz
1
01073-037
–6
10
Figure 35. VOCM Frequency Response
100
1k
10k
FREQUENCY (Hz)
100k
1M
Figure 37. Current Noise (RTI)
1000
VOUT, cm
400mV
5ns
100
10
5.7nV/ Hz
1
10
Figure 36. VOCM Transient Response
100
1k
10k
FREQUENCY (Hz)
Figure 38. Voltage Noise (RTI)
Rev. G | Page 14 of 24
100k
1M
01073-040
INPUT VOLTAGE NOISE (nV/ Hz)
VS = ±5V
VOCM = –1V TO +1V
01073-038
GAIN (dB)
0
01073-039
INPUT CURRENT NOISE (pA/ Hz)
VS = ±5V
3
Data Sheet
AD8138
TEST CIRCUITS
499Ω
RG = 499Ω
49.9Ω
RG = 499Ω
499Ω
49.9Ω
499Ω
RL, dm = 499Ω
AD8138
24.9Ω
01073-003
24.9Ω
RF = 499Ω
499Ω
24.9Ω
24.9Ω
AD8138
24.9Ω
CL
453Ω
499Ω
01073-027
499Ω
AD8138
249Ω
499Ω
Figure 41. Test Circuit for Output Balance
Figure 39. Basic Test Circuit
49.9Ω
499Ω
249Ω
Figure 40. Test Circuit for Cap Load Drive
Rev. G | Page 15 of 24
01073-030
RF = 499Ω
AD8138
Data Sheet
OPERATIONAL DESCRIPTION
DEFINITION OF TERMS
Common-mode voltage refers to the average of two node
voltages. The output common-mode voltage is defined as
CF
VOUT, cm = (V+OUT + V−OUT)/2
RF
RG
–OUT
+IN
VOCM
AD8138
–DIN
RG
RL, dm
VOUT, dm
+OUT
–IN
RF
CF
01073-041
+DIN
Figure 42. Circuit Definitions
Differential voltage refers to the difference between two node
voltages. For example, the output differential voltage (or
equivalently output differential-mode voltage) is defined as
Balance is a measure of how well differential signals are
matched in amplitude and exactly 180° apart in phase. Balance
is most easily determined by placing a well-matched resistor
divider between the differential voltage nodes and comparing
the magnitude of the signal at the midpoint of the divider with
the magnitude of the differential signal (see Figure 41). By this
definition, output balance is the magnitude of the output
common-mode voltage divided by the magnitude of the output
differential mode voltage:
VOUT, dm = (V+OUT − V−OUT)
where V+OUT and V−OUT refer to the voltages at the +OUT and
−OUT terminals with respect to a common reference.
Rev. G | Page 16 of 24
Output Balance Error =
VOUT , cm
VOUT , dm
Data Sheet
AD8138
THEORY OF OPERATION
The AD8138 differs from conventional op amps in that it has
two outputs whose voltages move in opposite directions. Like
an op amp, it relies on high open-loop gain and negative
feedback to force these outputs to the desired voltages. The
AD8138 behaves much like a standard voltage feedback op
amp and makes it easy to perform single-ended-to-differential
conversion, common-mode level-shifting, and amplification of
differential signals. Also like an op amp, the AD8138 has high
input impedance and low output impedance.
Previous differential drivers, both discrete and integrated
designs, have been based on using two independent amplifiers
and two independent feedback loops, one to control each of the
outputs. When these circuits are driven from a single-ended
source, the resulting outputs are typically not well balanced.
Achieving a balanced output has typically required exceptional
matching of the amplifiers and feedback networks.
DC common-mode level-shifting has also been difficult with
previous differential drivers. Level-shifting has required the use
of a third amplifier and feedback loop to control the output
common-mode level. Sometimes the third amplifier has also
been used to attempt to correct an inherently unbalanced
circuit. Excellent performance over a wide frequency range
has proven difficult with this approach.
The AD8138 uses two feedback loops to separately control the
differential and common-mode output voltages. The differential
feedback, set with external resistors, controls only the differential
output voltage. The common-mode feedback controls only the
common-mode output voltage. This architecture makes it easy
to arbitrarily set the output common-mode level. It is forced, by
internal common-mode feedback, to be equal to the voltage
applied to the VOCM input, without affecting the differential
output voltage.
ANALYZING AN APPLICATION CIRCUIT
The AD8138 uses high open-loop gain and negative feedback to
force its differential and common-mode output voltages in such
a way as to minimize the differential and common-mode error
voltages. The differential error voltage is defined as the voltage
between the differential inputs labeled +IN and −IN in Figure 42.
For most purposes, this voltage can be assumed to be zero.
Similarly, the difference between the actual output commonmode voltage and the voltage applied to VOCM can also be
assumed to be zero. Starting from these two assumptions, any
application circuit can be analyzed.
SETTING THE CLOSED-LOOP GAIN
Neglecting the capacitors CF, the differential-mode gain of the
circuit in Figure 42 can be determined to be described by
VOUT , dm
VIN , dm
=
S
RF
S
RG
This assumes the input resistors, RGS, and feedback resistors, RFS,
on each side are equal.
ESTIMATING THE OUTPUT NOISE VOLTAGE
Similar to the case of a conventional op amp, the differential
output errors (noise and offset voltages) can be estimated by
multiplying the input referred terms, at +IN and −IN, by the
circuit noise gain. The noise gain is defined as
R
GN = 1 +  F
 RG




To compute the total output referred noise for the circuit of
Figure 42, consideration must also be given to the contribution
of the Resistors RF and RG. Refer to Table 8 for the estimated
output noise voltage densities at various closed-loop gains.
The AD8138 architecture results in outputs that are very highly
balanced over a wide frequency range without requiring tightly
matched external components. The common-mode feedback
loop forces the signal component of the output common-mode
voltage to be zeroed. The result is nearly perfectly balanced
differential outputs of identical amplitude and exactly 180°apart
in phase.
Table 8.
Gain
1
2
5
10
RG (Ω)
499
499
499
499
RF (Ω)
499
1.0 k
2.49 k
4.99 k
Bandwidth −3 dB
320 MHz
180 MHz
70 MHz
30 MHz
Output Noise AD8138 Only
10 nV/√Hz
15 nV/√Hz
30 nV/√Hz
55 nV/√Hz
Rev. G | Page 17 of 24
Output Noise AD8138 + RG, RF
11.6 nV/√Hz
18.2 nV/√Hz
37.9 nV/√Hz
70.8 nV/√Hz
AD8138
Data Sheet
When using the AD8138 in gain configurations where RF/RG of
one feedback network is unequal to RF/RG of the other network,
there is a differential output noise due to input-referred voltage
in the VOCM circuitry. The output noise is defined in terms of
the following feedback terms (refer to Figure 42):
β1 =
RG
RF + RG
CALCULATING THE INPUT IMPEDANCE OF AN
APPLICATION
The effective input impedance of a circuit such as the one in
Figure 42, at +DIN and –DIN, depends on whether the amplifier is
being driven by a single-ended or differential signal source. For
balanced differential input signals, the input impedance (RIN, dm)
between the inputs (+DIN and −DIN) is simply
RIN, dm =2 × RG
for −OUT to +IN loop, and
β2 =
In the case of a single-ended input signal (for example if −DIN is
grounded and the input signal is applied to +DIN), the input
impedance becomes
RG
RF + RG
for +OUT to −IN loop. With these defined,
VnOUT , dm
 β − β2 
= 2VnIN ,VOCM  1

 β1 + β2 
RIN , dm
where VnOUT, dm is the output differential noise, and VnIN ,VCOM is
the input-referred voltage noise in VOCM.
THE IMPACT OF MISMATCHES IN THE FEEDBACK
NETWORKS
As previously mentioned, even if the external feedback
networks (RF/RG) are mismatched, the internal common-mode
feedback loop still forces the outputs to remain balanced. The
amplitudes of the signals at each output remains equal and 180°
out of phase. The input-to-output differential-mode gain varies
proportionately to the feedback mismatch, but the output
balance is unaffected.
Ratio matching errors in the external resistors result in a
degradation of the ability of the circuit to reject input commonmode signals, much the same as for a four-resistor difference
amplifier made from a conventional op amp.
In addition, if the dc levels of the input and output commonmode voltages are different, matching errors result in a small
differential-mode output offset voltage. For the G = 1 case, with
a ground referenced input signal and the output common-mode
level set for 2.5 V, an output offset of as much as 25 mV (1% of
the difference in common-mode levels) can result if 1% tolerance
resistors are used. Resistors of 1% tolerance result in a worstcase input CMRR of about 40 dB, worst-case differential mode
output offset of 25 mV due to 2.5 V level-shift, and no significant
degradation in output balance error.




RG


=
RF
1−


2 × (RG + RF ) 

The input impedance of the circuit is effectively higher than it
would be for a conventional op amp connected as an inverter
because a fraction of the differential output voltage appears at
the inputs as a common-mode signal, partially bootstrapping
the voltage across the input resistor RG.
INPUT COMMON-MODE VOLTAGE RANGE IN
SINGLE-SUPPLY APPLICATIONS
The AD8138 is optimized for level-shifting, ground-referenced
input signals. For a single-ended input, this would imply, for
example, that the voltage at −DIN in Figure 42 would be 0 V
when the negative power supply voltage of the amplifier (at V−)
is also set to 0 V.
SETTING THE OUTPUT COMMON-MODE VOLTAGE
The VOCM pin of the AD8138 is internally biased at a voltage
approximately equal to the midsupply point (average value of
the voltages on V+ and V−). Relying on this internal bias results
in an output common-mode voltage that is within about
100 mV of the expected value.
In cases where more accurate control of the output commonmode level is required, it is recommended that an external
source, or resistor divider (made up of 10 kΩ resistors), be used.
The output common-mode offset listed in the Specifications
section assumes the VOCM input is driven by a low impedance
voltage source.
DRIVING A CAPACITIVE LOAD
A purely capacitive load can react with the pin and bondwire
inductance of the AD8138, resulting in high frequency ringing
in the pulse response. One way to minimize this effect is to
place a small capacitor across each of the feedback resistors. The
added capacitance should be small to avoid destabilizing the
amplifier. An alternative technique is to place a small resistor in
series with the outputs of the amplifier, as shown in Figure 40.
Rev. G | Page 18 of 24
Data Sheet
AD8138
LAYOUT, GROUNDING, AND BYPASSING
As a high speed device, the AD8138 is sensitive to the PCB
environment in which it has to operate. Realizing its superior
specifications requires attention to various details of good high
speed PCB design.
The first requirement is for a good solid ground plane that
covers as much of the board area around the AD8138 as
possible. The only exception to this is that the two input pins
(Pin 1 and Pin 8) should be kept a few millimeters from the
ground plane, and ground should be removed from inner layers
and the opposite side of the board under the input pins. This
minimizes the stray capacitance on these nodes and helps
preserve the gain flatness vs. frequency.
The power supply pins should be bypassed as close as possible
to the device to the nearby ground plane. Good high frequency
ceramic chip capacitors should be used. This bypassing should
be done with a capacitance value of 0.01 µF to 0.1 µF for each
supply. Further away, low frequency bypassing should be provided
with 10 µF tantalum capacitors from each supply to ground.
The signal routing should be short and direct to avoid parasitic
effects. Wherever there are complementary signals, a symmetrical
layout should be provided to the extent possible to maximize
the balance performance. When running differential signals
over a long distance, the traces on the PCB should be close
together or any differential wiring should be twisted together to
minimize the area of the loop that is formed. This reduces the
radiated energy and makes the circuit less susceptible to
interference.
Rev. G | Page 19 of 24
AD8138
Data Sheet
BALANCED TRANSFORMER DRIVER
CSTRAY
VUNBAL
52.3Ω PRIMARY
CSTRAY
NO SIGNAL IS COUPLED
ON THIS SIDE
Figure 43. Transformer Single-Ended-to-Differential Converter Is Inherently
Imbalanced
499Ω
CSTRAY
49.9Ω
499Ω
The balance of a differential circuit can be measured by
connecting an equal-valued resistive voltage divider across the
differential outputs and then measuring the center point of the
circuit with respect to ground. Since the two differential outputs
are supposed to be of equal amplitude, but 180° opposite phase,
there should be no signal present for perfectly balanced outputs.
Figure 45 compares the transformer being driven singleendedly by a signal generator and being driven differentially
using an AD8138. The top signal trace of Figure 45 shows the
balance of the single-ended configuration, while the bottom
shows the differentially driven balance response. The 100 MHz
balance is 35 dB better when using the AD8138.
+IN
OUT–
VUNBAL
AD8138
OUT+
–IN
49.9Ω
500Ω
0.005%
VDIFF
500Ω
0.005%
499Ω
CSTRAY
499Ω
Figure 44. AD8138 Forms a Balanced Transformer Driver
0
OUTPUT BALANCE ERROR (dB)
The circuit in Figure 43 shows a Mini-Circuits® T1-6T
transformer connected with its primary driven single-endedly
and the secondary connected with a precision voltage divider
across its terminals. The voltage divider is made up of two
500 Ω, 0.005% precision resistors. The voltage VUNBAL, which is
also equal to the ac common-mode voltage, is a measure of how
closely the outputs are balanced.
500Ω
0.005%
SECONDARY V DIFF
500Ω
0.005%
01073-042
If the interwinding capacitance (CSTRAY) is assumed to be
uniformly distributed, a signal from the driving source couples
to the secondary output terminal that is closest to the driven
side of the primary. On the other hand, no signal is coupled to
the opposite terminal of the secondary because its nearest
primary terminal is not driven (see Figure 43). The exact
amount of this imbalance depends on the particular parasitics
of the trans-former, but is mostly a problem at higher
frequencies.
SIGNAL IS COUPLED
ON THIS SIDE VIA CSTRAY
01073-043
However, when driving the transformer in a single-ended
manner, there is an imbalance at the output due to the parasitics
inherent in the transformer. The primary (or driven) side of the
transformer has one side at dc potential (usually ground), while
the other side is driven. This can cause problems in systems that
require good balance of the differential output signals of the
transformer.
The well-balanced outputs of the AD8138 provide a drive signal
to each of the primary inputs of the transformer that are of
equal amplitude and 180° out of phase. Therefore, depending
on how the polarity of the secondary is connected, the signals
that conduct across the interwinding capacitance either both
assist the secondary signal of the transformer equally, or both
buck the secondary signals. In either case, the parasitic effect is
symmetrical and provides a well-balanced transformer output
(see Figure 45).
–20
–40
VUNBAL , FOR TRANSFORMER
WITH SINGLE-ENDED DRIVE
–60
–80
VUNBAL , DIFFERENTIAL DRIVE
–100
0.3
1
10
FREQUENCY (MHz)
100
500
01073-044
Transformers are among the oldest devices used to perform a
single-ended-to-differential conversion (and vice versa). Transformers can also perform the additional functions of galvanic
isolation, step-up or step-down of voltages, and impedance
transformation. For these reasons, transformers always find
uses in certain applications.
Figure 45. Output Balance Error for Circuits of Figure 43 and Figure 44
Rev. G | Page 20 of 24
Data Sheet
AD8138
HIGH PERFORMANCE ADC DRIVING
The signal generator has a ground-referenced, bipolar output,
that is, it drives symmetrically above and below ground.
Connecting VOCM to the CML pin of the AD9224 sets the output
common-mode of the AD8138 at 2.5 V, which is the midsupply
level for the AD9224. This voltage is bypassed by a 0.1 µF
capacitor.
The circuit in Figure 46 shows a simplified front-end
connection for an AD8138 driving an AD9224, a 12-bit,
40 MSPS ADC. The ADC works best when driven differentially,
which minimizes its distortion. The AD8138 eliminates the
need for a transformer to drive the ADC and performs singleended-to-differential conversion, common-mode level-shifting,
and buffering of the driving signal.
The full-scale analog input range of the AD9224 is set to
4 V p-p, by shorting the SENSE terminal to AVSS. This has
been determined to be the scaling to provide minimum
harmonic distortion.
The positive and negative outputs of the AD8138 are connected
to the respective differential inputs of the AD9224 via a pair of
49.9 Ω resistors to minimize the effects of the switched-capacitor
front end of the AD9224. For best distortion performance, it
runs from supplies of ±5 V.
For the AD8138 to swing at 4 V p-p, each output swings 2 V p-p
while providing signals that are 180° out of phase. With a
common-mode voltage at the output of 2.5 V, each AD8138
output swings between 1.5 V and 3.5 V.
The AD8138 is configured with unity gain for a single-ended,
input-to-differential output. The additional 23 Ω, 523 Ω total, at
the input to −IN is to balance the parallel impedance of the
50 Ω source and its 50 Ω termination that drives the
noninverting input.
A ground-referenced 4 V p-p, 5 MHz signal at DIN+ was used to
test the circuit in Figure 46. When the combined-device circuit
was run with a sampling rate of 20 MSPS, the spurious-free
dynamic range (SFDR) was measured at −85 dBc.
+5V
+5V
499Ω
3
499Ω
49.9Ω
2
523Ω
+
5
49.9Ω
24 VINB
0.1µF
15 26
28
AVDD
DRVDD
VOCM
AD8138
4
1
49.9Ω
23 VINA
6
0.1µF
DIGITAL
OUTPUTS
AD9224
AVSS
16 25
SENSE CML
17
22
DRVSS
27
499Ω
01073-045
50Ω
SOURCE
8
0.1µF
–5V
Figure 46. AD8138 Driving an AD9224, a 12-Bit, 40 MSPS ADC
Rev. G | Page 21 of 24
AD8138
Data Sheet
3 V OPERATION
The circuit in Figure 47 shows a simplified front-end
connection for an AD8138 driving an AD9203, a 10-bit,
40 MSPS ADC that is specified to work on a single 3 V supply.
The ADC works best when driven differentially to make the
best use of the signal swing available within the 3 V supply.
The appropriate outputs of the AD8138 are connected to the
appropriate differential inputs of the AD9203 via a low-pass filter.
The circuit was tested with a −0.5 dBFS signal at various
frequencies. Figure 48 shows a plot of the total harmonic
distortion (THD) vs. frequency at signal amplitudes of 1 V and
2 V differential drive levels.
–40
–45
–50
The AD8138 is configured for unity gain for a single-ended
input to differential output. The additional 23 Ω at the input to
−IN is to balance the impedance of the 50 Ω source and its 50 Ω
termination that drives the noninverting input.
THD (dBc)
–55
AD8138–2V
–60
–65
The signal generator has ground-referenced, bipolar output,
that is, it can drive symmetrically above and below ground.
Even though the AD8138 has ground as its negative supply, it
can still function as a level-shifter with such an input signal.
AD8138–1V
–70
–80
0
The output common mode is raised up to midsupply by the
voltage divider that biases VOCM. In this way, the AD8138
provides dc coupling and level-shifting of a bipolar signal,
without inverting the input signal.
AD8138
523Ω
4
1
0.1µF
6
49.9Ω
20pF
49.9Ω
20pF
28
25
AVDD
AINP
AINN
26
61
59
2
DRVDD
AD9203
AVSS
DRVSS
27
1
DIGITAL
OUTPUTS
57
AD8138–1V
55
AD8138–2V
53
51
499Ω
01073-046
10kΩ
Figure 47. AD8138 Driving an AD9203, a 10-Bit, 40 MSPS Analog-to-Digital
Converter
49
47
45
0
5
10
15
FREQUENCY (MHz)
20
Figure 49. AD9203 SINAD at −0.5 dBFS AD8138
Rev. G | Page 22 of 24
25
01073-048
2
5
0.1µF
SINAD (dBc)
3
+
63
0.1µF
499Ω
8
25
Figure 49 shows the signal-to-noise-and-distortion (SINAD)
under the same conditions as above. For the smaller signal
swing, the AD8138 performance is quite good, but its
performance degrades when trying to swing too close to the
supply rails.
3V
10kΩ
499Ω
20
65
3V
49.9Ω
10
15
FREQUENCY (MHz)
Figure 48. AD9203 THD at −0.5 dBFS AD8138
The low-pass filter between the AD8138 and the AD9203
provides filtering that helps to improve the signal-to-noise ratio
(SNR). Lower noise can be realized by lowering the pole
frequency, but the bandwidth of the circuit is lowered.
0.1µF
5
01073-047
–75
Data Sheet
AD8138
OUTLINE DIMENSIONS
3.20
3.00
2.80
5.00 (0.1968)
4.80 (0.1890)
8
5
4.00 (0.1574)
3.80 (0.1497) 1
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
6.20 (0.2440)
5.80 (0.2284)
8
3.20
3.00
2.80
1.75 (0.0688)
1.35 (0.0532)
1
0.50 (0.0196)
× 45°
0.25 (0.0099)
5
5.15
4.90
4.65
4
PIN 1
0.65 BSC
0.51 (0.0201)
COPLANARITY
SEATING 0.31 (0.0122)
0.10
PLANE
0.95
0.85
0.75
8°
0.25 (0.0098) 0° 1.27 (0.0500)
0.40 (0.0157)
0.17 (0.0067)
1.10 MAX
0.15
0.00
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
0.38
0.22
COPLANARITY
0.10
0.23
0.08
8°
0°
0.80
0.60
0.40
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 51. 8-Lead Mini Small Outline Package [MSOP]
(RM-8)
Dimensions shown in millimeters
Figure 50. 8-Lead Standard Small Outline Package [SOIC]
(R-8)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model 1
AD8138AR
AD8138AR-REEL
AD8138AR-REEL7
AD8138ARZ
AD8138ARZ-RL
AD8138ARZ-R7
AD8138ARM
AD8138ARM-REEL
AD8138ARM-REEL7
AD8138ARMZ
AD8138ARMZ-REEL
AD8138ARMZ-REEL7
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
8-Lead SOIC
8-Lead SOIC, 13" Tape and Reel
8-Lead SOIC, 7" Tape and Reel
8-Lead SOIC
8-Lead SOIC, 13" Tape and Reel
8-Lead SOIC, 7" Tape and Reel
8-Lead MSOP
8-Lead MSOP, 13" Tape and Reel
8-Lead MSOP, 7" Tape and Reel
8-Lead MSOP
8-Lead MSOP, 13" Tape and Reel
8-Lead MSOP, 7" Tape and Reel
Z = RoHS Compliant Part. # denotes RoHS compliant part may be top or bottom marked.
Rev. G | Page 23 of 24
Package Option
R-8
R-8
R-8
R-8
R-8
R-8
RM-8
RM-8
RM-8
RM-8
RM-8
RM-8
Branding
HBA
HBA
HBA
HBA#
HBA#
HBA#
AD8138
Data Sheet
NOTES
©1999–2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D01073-0-3/16(G)
Rev. G | Page 24 of 24