ETC AD8138ARM

a
FEATURES
Easy to Use Single-Ended-to-Differential Conversion
Adjustable Output Common-Mode Voltage
Externally Adjustable Gain
Low Harmonic Distortion
–94 dBc—Second, <–114 dBc—Third @ 5 MHz into
800 ⍀ Load
–87 dBc—Second, –85 dBc—Third @ 20 MHz into
800 ⍀ Load
–3 dB Bandwidth of 320 MHz, G = +1
Fast Settling to 0.01% of 16 ns
Slew Rate 1150 V/␮s
Fast Overdrive Recovery of 4 ns
Low Input Voltage Noise of 5 nV/√Hz
1 mV Typical Offset Voltage
Wide Supply Range +3 V to ⴞ5 V
Low Power 90 mW on 5 V
0.1 dB Gain Flatness to 40 MHz
Available in 8-Lead SOIC and MICRO_SOIC
APPLICATIONS
ADC Driver
Single-Ended-to-Differential Converter
IF and Baseband Gain Block
Differential Buffer
Line Driver
PRODUCT DESCRIPTION
AD8138 is a major advancement over op amps for differential
signal processing. The AD8138 can be used as a single-endedto-differential amplifier or as a differential-to-differential amplifier.
The AD8138 is as easy to use as an op amp, and greatly simplifies differential signal amplification and driving.
Manufactured on ADI’s proprietary XFCB bipolar process, the
AD8138 has a –3 dB bandwidth of 320 MHz and delivers a
differential signal with the lowest harmonic distortion available
in a differential amplifier. The AD8138 has a unique internal
feedback feature that provides output gain and phase matching
that are balanced, suppressing even order harmonics. The internal
feedback circuit also minimizes any gain error that would be associated with the mismatches in the external gain setting resistors.
The AD8138’s differential output helps balance the input-todifferential ADCs, maximizing the performance of the ADC.
The AD8138 eliminates the need for a transformer with high
Low Distortion
Differential ADC Driver
AD8138
FUNCTIONAL BLOCK DIAGRAM
1
8 +IN
VOCM 2
7 NC
–IN
V+ 3
6 V–
+OUT 4
5 –OUT
AD8138
NC = NO CONNECT
TYPICAL APPLICATION CIRCUIT
+5V
+5V
499⍀
VIN
499⍀
+
VOCM
499⍀
AIN
DVDD
DIGITAL
OUTPUTS
ADC
AD8138
AIN
–
AVDD
AVSS
VREF
499⍀
performance ADCs, preserving the low frequency and dc information. The common-mode level of the differential output is
adjustable by a voltage on the VOCM pin, easily level-shifting
the input signals for driving single supply ADCs. Fast overload
recovery preserves sampling accuracy.
The AD8138 distortion performance makes it an ideal ADC
driver for communication systems, with distortion performance
good enough to drive state-of-the-art 10- to 16-bit converters
at high frequencies. The AD8138’s high bandwidth and IP3
also make it appropriate for use as a gain block in IF and
baseband signal chains. The AD8138 offset and dynamic performance make it well suited for a wide variety of signal
processing and data acquisition applications.
The AD8138 is available in both SOIC and MICRO_SOIC
packages for operation over –40°C to +85°C temperatures.
REV. C
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2001
AD8138–SPECIFICATIONS
(@ 25ⴗC, VS = ⴞ5 V, VOCM = 0, G = +1, RL,dm = 500 ⍀, unless otherwise noted. Refer
to Figure 1 for test setup and label descriptions. All specifications refer to single-ended input and differential outputs unless otherwise noted.)
Parameter
Conditions
Min
VOUT = 0.5 V p-p, CF = 0 pF
VOUT = 0.5 V p-p, CF = 1 pF
VOUT = 0.5 V p-p, CF = 0 pF
VOUT = 2 V p-p, CF = 0 pF
VOUT = 2 V p-p, CF = 0 pF
0.01%, VOUT = 2 V p-p, CF = 1 pF
VIN = 5 V to 0 V Step, G = +2
290
AD8138
Typ
Max
Unit
ⴞDIN to ⴞOUT Specifications
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
Settling Time
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
Third Harmonic
IMD
IP3
Voltage Noise (RTI)
Input Current Noise
INPUT CHARACTERISTICS
Offset Voltage
VOUT = 2 V p-p, 5 MHz, RL,dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL,dm = 800 Ω
VOUT = 2 V p-p, 70 MHz, RL,dm = 800 Ω
VOUT = 2 V p-p, 5 MHz, RL,dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL,dm = 800 Ω
VOUT = 2 V p-p, 70 MHz, RL,dm = 800 Ω
20 MHz
20 MHz
f = 100 kHz to 40 MHz
f = 100 kHz to 40 MHz
VOS,dm = VOUT,dm/2; VDIN+ = VDIN– = VOCM = 0 V
TMIN–TMAX Variation
–2.5
Input Bias Current
Input Resistance
Input Capacitance
Input Common-Mode Voltage
CMRR
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current
Output Balance Error
TMIN–TMAX Variation
Differential
Common Mode
∆VOUT,dm/∆VIN,cm; ∆VIN,cm = ± 1 V
Maximum ∆VOUT; Single-Ended Output
∆VOUT,cm/∆VOUT,dm; ∆VOUT,dm = 1 V
320
225
30
265
1150
16
4
MHz
MHz
MHz
MHz
V/µs
ns
ns
–94
–87
–62
–114
–85
–57
–77
37
5
2
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBm
nV/√Hz
pA/√Hz
±1
±4
3.5
–0.01
6
3
1
–4.7 to +3.4
–77
+2.5
7
–70
mV
µV/°C
µA
µA/°C
MΩ
MΩ
pF
V
dB
7.75
95
–66
V p-p
mA
dB
250
330
MHz
V/µs
VOCM to ⴞOUT Specifications
DYNAMIC PERFORMANCE
–3 dB Bandwidth
Slew Rate
DC PERFORMANCE
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Bias Current
VOCM CMRR
Gain
VOS,cm = VOUT,cm; VDIN+ = VDIN– = VOCM = 0 V
[∆VOUT,dm/∆VOCM]; ∆VOCM = ± 1 V
∆VOUT,cm/∆VOCM; ∆VOCM = ± 1 V
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
± 3.8
200
–3.5
±1
0.5
–75
0.9955 1
1.0045
± 1.4
18
± 5.5
23
TMIN to TMAX Variation
∆VOUT,dm/∆VS; ∆VS = ± 1 V
OPERATING TEMPERATURE RANGE
20
40
–90
–40
+3.5
V
kΩ
mV
µA
dB
V/V
–70
V
mA
µA/°C
dB
+85
°C
NOTES
Harmonic Distortion Performance is equal or slightly worse with higher values of R L,dm. See TPCs 13 and 14 for more information.
Specifications subject to change without notice.
–2–
REV. C
AD8138
(@ 25ⴗC, V = 5 V, V = 2.5 V, G = +1, R = 500 ⍀, unless otherwise noted. Refer to Figure 1 for test
SPECIFICATIONS
setup and label descriptions. All specifications refer to single-ended input and differential outputs unless otherwise noted.)
S
Parameter
OCM
L,dm
Conditions
Min
VOUT = 0.5 V p-p, CF = 0 pF
VOUT = 0.5 V p-p, CF = 1 pF
VOUT = 0.5 V p-p, CF = 0 pF
VOUT = 2 V p-p, CF = 0 pF
VOUT = 2 V p-p, CF = 0 pF
0.01%, VOUT = 2 V p-p, CF = 1 pF
VIN = 2.5 V to 0 V Step, G = +2
280
AD8138
Typ
Max
Unit
ⴞDIN to ⴞOUT Specifications
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
Settling Time
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
Third Harmonic
IMD
IP3
Voltage Noise (RTI)
Input Current Noise
INPUT CHARACTERISTICS
Offset Voltage
VOUT = 2 V p-p, 5 MHz, RL,dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL,dm = 800 Ω
VOUT = 2 V p-p, 70 MHz, RL,dm = 800 Ω
VOUT = 2 V p-p, 5 MHz, RL,dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL,dm = 800 Ω
VOUT = 2 V p-p, 70 MHz, RL,dm = 800 Ω
20 MHz
20 MHz
f = 100 kHz to 40 MHz
f = 100 kHz to 40 MHz
VOS,dm = VOUT,dm/2; VDIN+ = VDIN– = VOCM = 2.5 V
TMIN–TMAX Variation
–2.5
Input Bias Current
Input Resistance
Input Capacitance
Input Common-Mode Voltage
CMRR
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current
Output Balance Error
TMIN–TMAX Variation
Differential
Common Mode
∆VOUT,dm/∆VIN,cm; ∆VIN,cm = 1 V
Maximum ∆VOUT; Single-Ended Output
310
225
29
265
950
16
4
MHz
MHz
MHz
MHz
V/µs
ns
ns
–90
–79
–60
–100
–82
–53
–74
35
5
2
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBm
nV/√Hz
pA/√Hz
±1
±4
3.5
–0.01
6
3
1
0.3 to 3.2
–77
+2.5
7
–70
mV
µV/°C
µA
µA/°C
MΩ
MΩ
pF
V
dB
2.9
95
–65
V p-p
mA
dB
DYNAMIC PERFORMANCE
–3 dB Bandwidth
Slew Rate
220
250
MHz
V/µs
DC PERFORMANCE
Input Voltage Range
Input Resistance
Input Offset Voltage
1.0 to 3.8
100
±1
V
kΩ
∆VOUT,cm/∆VOUT,dm; ∆VOUT,dm = 1 V
VOCM to ⴞOUT Specifications
Input Bias Current
VOCM CMRR
Gain
–5
[∆VOUT,dm/∆VOCM]; ∆VOCM = 2.5 ± 1 V
∆VOUT,cm/∆VOCM; ∆VOCM = 2.5 ± 1 V
0.5
–70
0.9968 1
1.0032
2.7
15
11
21
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
TMIN to TMAX Variation
∆VOUT,dm/∆VS; ∆VS = ± 1 V
OPERATING TEMPERATURE RANGE
20
40
–90
–40
NOTES
Harmonic Distortion Performance is equal or slightly worse with higher values of R L,dm. See Figures TPC 13 and 14 for more information.
Specifications subject to change without notice.
REV. C
+5
VOS,cm = VOUT,cm; VDIN+ = VDIN– = VOCM = 2.5 V
–3–
mV
µA
dB
V/V
–70
V
mA
µA/°C
dB
+85
°C
AD8138
ABSOLUTE MAXIMUM RATINGS 1
PIN FUNCTION DESCRIPTIONS
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 5.5 V
VOCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± VS
Internal Power Dissipation . . . . . . . . . . . . . . . . . . . . 550 mW
θJA2 (SOIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155°C/W
Operating Temperature Range . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering 10 sec) . . . . . . . . . . . . . 300°C
Pin No. Name
1
2
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above listed in the operational section of this
specification is not implied. Exposure to Absolute Maximum Ratings for any
extended periods may affect device reliability.
2
Thermal resistance measured on SEMI standard 4-layer board.
3
4
5
6
7
8
RF = 499⍀
Function
–IN
VOCM
Negative Input Summing Node
Voltage applied to this pin sets the commonmode output voltage with a ratio of 1:1. For
example, 1 V dc on VOCM will set the dc bias
level on +OUT and –OUT to 1 V.
V+
Positive Supply Voltage
+OUT Positive Output. Note: the voltage at –DIN is
inverted at +OUT.
–OUT Negative Output. Note: the voltage at +DIN
is inverted at –OUT.
V–
Negative Supply Voltage
NC
No Connect
+IN
Positive Input Summing Node
RG = 499⍀
49.9⍀
RG = 499⍀
24.9⍀
AD8138
RL,dm = 499⍀
PIN CONFIGURATION
RF = 499⍀
1
8 +IN
VOCM 2
7 NC
–IN
Figure 1. Basic Test Circuit
V+ 3
6 V–
+OUT 4
5 –OUT
AD8138
NC = NO CONNECT
ORDERING GUIDE
Model
AD8138AR
AD8138AR-REEL1
AD8138AR-REEL72
AD8138ARM
AD8138ARM-REEL3
AD8138ARM-REEL72
AD8138-EVAL
Temperature
Range
Package
Descriptions
Package
Options
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
8-Lead SOIC
8-Lead SOIC
8-Lead SOIC
8-Lead MICRO_SOIC
8-Lead SOIC
8-Lead SOIC
Evaluation Board
SO-8
13" Tape and Reel
7" Tape and Reel
RM-8
13" Tape and Reel
7" Tape and Reel
SOIC
Branding
Information
HBA
HBA
HBA
NOTES
1
13" Reels of 2500 each.
2
7" Reels of 1000 each.
3
13" Reels of 3000 each.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD8138 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. C
Typical Performance Characteristics–AD8138
Unless otherwise noted, GAIN = 1, RG = RF = RL,dm = 499 ⍀, TA = 25ⴗC; Refer to Figure 1 for test setup.
6
6
0.5
VS = ⴞ5V
VIN = 0.2V p-p
VIN = 0.2V p-p
CF = 0pF
3
3
0.3
CF = 0pF
0
VS = ⴞ5V
–3
GAIN – dB
CF = 0pF
GAIN – dB
VS = +5V
GAIN – dB
VS = ⴞ5V
VIN = 0.2V p-p
0
CF = 1pF
–3
0.1
–0.1
CF = 1pF
–6
–6
–9
–0.3
–9
10
100
FREQUENCY – MHz
1
1000
TPC 1. Small Signal Frequency
Response
–0.5
1
10
100
FREQUENCY – MHz
30
VIN = 2V p-p
VS = ⴞ5V
3
G = 10, RF = 4.99k⍀
3
VS = +5V
20
VS = ⴞ5V
–3
GAIN – dB
GAIN – dB
CF = 0pF
0
0
CF = 1pF
–3
VS = ⴞ5V
CF = 0pF
VOUT,dm = 0.2V p-p
RG = 499⍀
G = 5, RF = 2.49k⍀
10
G = 2, RF = 1k⍀
G = 1, RF = 499⍀
0
–6
100
TPC 3. 0.1 dB Flatness vs.
Frequency
6
VIN = 2V p-p
CF = 0pF
–6
–9
–9
10
100
FREQUENCY – MHz
1000
TPC 4. Large Signal Frequency
Response
DISTORTION – dBc
HD2(VS = ⴞ5V)
–90
–100
HD3(VS = +5V)
–110
–120
0
10
20
30
40
50
60
FUNDAMENTAL FREQUENCY – MHz
TPC 7. Harmonic Distortion vs.
Frequency
REV. C
TPC 6. Small Signal Frequency
Response for Various Gains
–30
70
–40
HD3(VS = +5V)
–60
–70
HD2(VS = +5V)
–80
HD2(VS = ⴞ5V)
–90
–100
HD3(VS = ⴞ5V)
–110
1000
10
100
FREQUENCY – MHz
1
VOUT,dm = 4V p-p
RL = 800⍀
–50
HD2(VS = +5V)
–80
1000
–40
VOUT,dm = 2V p-p
RL = 800⍀
–70
10
100
FREQUENCY – MHz
TPC 5. Large Signal Frequency
Response
–50
–60
–10
1
DISTORTION – dBc
1
DISTORTION – dBc
10
FREQUENCY – MHz
1
TPC 2. Small Signal Frequency
Response
6
GAIN – dB
1000
HD3(VS = ⴞ5V)
0
10
20
30
40
50
60
FUNDAMENTAL FREQUENCY – MHz
TPC 8. Harmonic Distortion vs.
Frequency
–5–
70
VOUT,dm = 2V p-p
RL = 800⍀
FO = 20MHz
–50
HD2(VS = +5)
–60
HD3(VS = +5)
–70
–80
HD3(VS = ⴞ5)
–90
HD2(VS = ⴞ5)
–100
–4
–3
–2
–1
0
1
2
VOCM DC OUTPUT – Volts
3
TPC 9. Harmonic Distortion vs.
VOCM
4
AD8138
–70
–60
–60
VS = ⴞ5V
RL = 800⍀
HD3(F = 20MHz)
–70
HD2(F = 20MHz)
–80
–90
HD2(F = 5MHz)
–100
–80
HD3(F = 20MHz)
–90
HD2(F = 5MHz)
–100
HD3(F = 5MHz)
HD3(F = 5MHz)
–110
–80
–90
HD2(F = 5MHz)
–100
HD3(F = 5MHz)
–110
0
1
2
3
4
–120
6
5
DIFFERENTIAL OUTPUT VOLTAGE – V p-p
TPC 10. Harmonic Distortion vs.
Differential Output Voltage
1
0
2
3
4
–110
0.25
DIFFERENTIAL OUTPUT VOLTAGE – V p-p
TPC 11. Harmonic Distortion vs.
Differential Output Voltage
–60
–60
VS = +5V
VOUT,dm = 2V p-p
0.50
0.75
1.00
1.25
1.50
1.75
DIFFERENTIAL OUTPUT VOLTAGE – V p-p
TPC 12. Harmonic Distortion vs.
Differential Output Voltage
10
VS = ⴞ5V
VOUT,dm = 2V p-p
–70
–70
FC = 50MHz
VS = ⴞ5V
–10
HD2(F = 20MHz)
DISTORTION – dBc
HD2(F = 20MHz)
DISTORTION – dBc
HD2(F = 20MHz)
–80
HD3(F = 20MHz)
–90
HD2(F = 5MHz)
HD3(F = 20MHz)
–80
–90
HD2(F = 5MHz)
–100
POUT – dBm
–120
HD3(F = 20MHz)
–70
HD2(F = 20MHz)
DISTORTION – dBc
DISTORTION – dBc
VS = +3V
RL = 800⍀
VS = +5V
RL = 800⍀
DISTORTION – dBc
–60
–30
–50
–70
HD3(F = 5MHz)
–100
–110
HD3(F = 5MHz)
–110
200
600
1000
1400
–90
–120
200
1800
600
RLOAD – ⍀
1000
1400
RLOAD – ⍀
1800
TPC 14. Harmonic Distortion vs.
RLOAD
TPC 13. Harmonic Distortion vs.
RLOAD
–110
49.5
49.7
49.9
50.1
50.3
FREQUENCY – MHz
TPC 15. Intermodulation
Distortion
VS = ⴞ5V
45
RL = 800⍀
50.5
CF = 0pF
VOUT,dm = 0.2V p-p
VS = ⴞ5V
VOUT,dm
INTERCEPT – dBm
40
CF = 1pF
VOUT–
VS = +5V
35
VOUT+
VS = ⴞ5V
V+DIN
30
1V
25
0
20
40
60
5ns
40mV
5ns
80
FREQUENCY – MHz
TPC 16. Third Order Intercept vs.
Frequency
TPC 17. Large Signal Transient
Response
–6–
TPC 18. Small Signal Transient
Response
REV. C
AD8138
VS = ⴞ5V
CF = 0pF
VOUT,dm = 2V p-p
CF = 0pF
VS = ⴞ5V
CF = 1pF
200␮V
VOUT,dm = 2V p-p
VS = ⴞ5V
VOUT,dm
VS = +5V
CF = 1pF
V+DIN
400mV
400mV
5ns
5ns
1V
TPC 20. Large Signal Transient
Response
TPC 19. Large Signal Transient
Response
4ns
TPC 21. Settling Time
VS = ⴞ5V
CF = 0pF
CL = 10pF
CL = 5pF
VOUT,dm
499⍀
VS = ⴞ5V
F = 20MHz
V+DIN = 8V p-p
G = 3(RF = 1500)
499⍀
49.9⍀
499⍀
24.9⍀
CL = 20pF
24.9⍀
AD8138
24.9⍀
CL
453⍀
499⍀
V+DIN
4V
400mV
30ns
TPC 23. Test Circuit for Cap Load
Drive
TPC 22. Output Overdrive
TPC 24. Large Signal Transient
Response for Various Cap Loads
–20
–20
VS = ⴞ5V
⌬VOUT,dm/⌬VIN,cm
–30
2.5ns
VIN = 2V p-p
CMRR – dB
–40
499⍀
49.9⍀
499⍀
–50
24.9⍀
–60
249⍀
AD8138
249⍀
499⍀
BALANCE ERROR – dB
–30
499⍀
–40
VS = ⴞ5V
–50
–60
–70
VS = +5V
–80
–70
1
10
100
FREQUENCY – MHz
TPC 25. CMRR vs. Frequency
REV. C
1k
1
TPC 26. Test Circuit for Output
Balance
–7–
10
100
FREQUENCY – MHz
1k
TPC 27. Output Balance Error vs.
Frequency
AD8138
5.0
100
⌬VOUT,dm/⌬VS
DIFFERENTIAL OUTPUT OFFSET – mV
–10
SINGLE-ENDED OUTPUT
–20
–40
–50
–60
+PSRR
(VS = +5V, 0V AND ⴞ5V)
–70
10
VS = +5
1
VS = ⴞ5V
–80
0.1
–90
1
10
100
FREQUENCY – MHz
1k
1
VS = ⴞ5V
VS = +5V
0
VS = +3V
–2.5
–5.0
–40
–20
40
0
20
60
TEMPERATURE – ⴗC
80
100
TPC 30. Output Referred Differential
Offset Voltage vs. Temperature
6
30
5
VS = +5V
SUPPLY CURRENT – mA
BIAS CURRENT – ␮A
100
TPC 29. Output Impedance vs.
Frequency
TPC 28. PSRR vs. Frequency
4
VS = ⴞ5V, +5V
3
VS = +3V
2
1
–40
10
FREQUENCY – MHz
2.5
VS = ⴞ5V
20
VS = +5V
15
40
0
20
60
TEMPERATURE – ⴗC
80
TPC 31. Input Bias Current vs.
Temperature
100
0
–3
VS = +3V
–6
10
–20
VS = ⴞ5V
3
25
GAIN – dB
PSRR – dB
IMPEDANCE – ⍀
–PSRR
(VS = ⴞ5V)
–30
5
–40
–9
–20
40
0
20
60
TEMPERATURE – ⴗC
80
100
TPC 32. Supply Current vs.
Temperature
1
10
100
FREQUENCY – MHz
1k
TPC 33. VOCM Frequency Response
VS = ⴞ5V
VOCM = –1V TO +1V
VOUT,cm
400mV
5ns
TPC 34. VOCM Transient Response
–8–
REV. C
AD8138
OPERATIONAL DESCRIPTION
Definition of Terms
CF
RF
+DIN
RG
+IN
AD8138
VOCM
–DIN
–OUT
RG
–IN
RL,dm
VOUT,dm
+OUT
RF
CF
Figure 2. Circuit Definitions
Differential voltage refers to the difference between two node
voltages. For example, the output differential voltage (or
equivalently output differential-mode voltage) is defined as:
VOUT,dm = (V+OUT – V–OUT)
V+OUT and V–OUT refer to the voltages at the +OUT and –OUT
terminals with respect to a common reference.
Common-mode voltage refers to the average of two node voltages. The output common-mode voltage is defined as:
VOUT,cm = (V+OUT + V–OUT)/2
Balance is a measure of how well differential signals are matched in
amplitude and exactly 180 degrees apart in phase. Balance is most
easily determined by placing a well-matched resistor divider
between the differential voltage nodes and comparing the magnitude of the signal at the divider’s midpoint with the magnitude
of the differential signal. (See TPC 26.) By this definition, output
balance is the magnitude of the output common-mode voltage
divided by the magnitude of the output differential-mode voltage:
Output Balance Error =
Analyzing an Application Circuit
The AD8138 uses high open-loop gain and negative feedback to
force its differential and common-mode output voltages in such
a way as to minimize the differential and common-mode error
voltages. The differential error voltage is defined as the voltage
between the differential inputs labeled +IN and –IN in Figure 2.
For most purposes, this voltage can be assumed to be zero.
Similarly, the difference between the actual output commonmode voltage and the voltage applied to VOCM can also be assumed
to be zero. Starting from these two assumptions, any application
circuit can be analyzed.
Setting the Closed Loop Gain
Neglecting the capacitors CF, the differential mode gain of the
circuit in Figure 2 can be determined to be described by the
following equation:
VOUT , cm
VOUT , dm
VIN , dm
VOUT , dm
THEORY OF OPERATION
The AD8138 differs from conventional op amps in that it has
two outputs whose voltages move in opposite directions. Like an
op amp, it relies on high open loop gain and negative feedback
to force these outputs to the desired voltages. The AD8138
behaves much like a standard voltage feedback op amp and makes
it easy to perform single-ended-to-differential conversion,
common-mode level-shifting, and amplification of differential
signals. Also like an op amp, the AD8138 has high input impedance and low output impedance.
Previous differential drivers, both discrete and integrated
designs, have been based on using two independent amplifiers,
and two independent feedback loops, one to control each of the
outputs. When these circuits are driven from a single-ended
source, the resulting outputs are typically not well balanced.
Achieving a balanced output has typically required exceptional
matching of the amplifiers and feedback networks.
DC common-mode level-shifting has also been difficult with
previous differential drivers. Level-shifting has required the use
of a third amplifier and feedback loop to control the output
common-mode level. Sometimes the third amplifier has also
been used to attempt to correct an inherently unbalanced
REV. C
circuit. Excellent performance over a wide frequency range has
proven difficult with this approach.
The AD8138 uses two feedback loops to separately control the
differential and common-mode output voltages. The differential
feedback, set with external resistors, controls only the differential output voltage. The common-mode feedback controls only
the common-mode output voltage. This architecture makes it
easy to arbitrarily set the output common-mode level. It is forced,
by internal common-mode feedback, to be equal to the voltage
applied to the VOCM input, without affecting the differential
output voltage.
The AD8138 architecture results in outputs that are very highly
balanced over a wide frequency range without requiring tightly
matched external components. The common-mode feedback
loop forces the signal component of the output common-mode
voltage to be zeroed. The result is nearly perfectly balanced
differential outputs, of identical amplitude and exactly 180
degrees apart in phase.
=
RF S
RG S
This assumes the input resistors, RGS and feedback resistors,
RFS on each side are equal.
Estimating the Output Noise Voltage
Similar to the case of a conventional op amp, the differential
output errors (noise and offset voltages) can be estimated by
multiplying the input referred terms, at +IN and –IN, by the
circuit noise gain. The noise gain is defined as:
R 
GN = 1 +  F 
 RG 
To compute the total output referred noise for the circuit of
Figure 2, consideration must also be given to the contribution of
the resistors RF and RG. Refer to Table I for estimated output
noise voltage densities at various closed-loop gains.
Table I
Gain
RG RF
(⍀) (⍀)
Bandwidth Output Noise
–3 dB
8138 Only
Output Noise
8138 + RG, RF
1
2
5
10
499
499
499
499
320 MHz
180 MHz
70 MHz
30 MHz
11.5 nV/√Hz
16.6 nV/√Hz
31.6 nV/√Hz
56.6 nV/√Hz
–9–
499
1.0 k
2.49 k
4.99 k
10 nV/√Hz
15 nV/√Hz
30 nV/√Hz
55 nV/√Hz
AD8138
The Impact of Mismatches in the Feedback Networks
Setting the Output Common-Mode Voltage
As mentioned previously, even if the external feedback networks
(RF/RG) are mismatched, the internal common-mode feedback
loop will still force the outputs to remain balanced. The amplitudes of the signals at each output will remain equal and 180
degrees out of phase. The input-to-output differential-mode
gain will vary proportionately to the feedback mismatch, but the
output balance will be unaffected.
The AD8138’s VOCM pin is internally biased at a voltage
approximately equal to the midsupply point (average value of
the voltages on V+ and V–). Relying on this internal bias will
result in an output common-mode voltage that is within about
100 mV of the expected value.
Ratio matching errors in the external resistors will result in a
degradation of the circuit’s ability to reject input common-mode
signals, much the same as for a four-resistor difference amplifier
made from a conventional op amp.
Also, if the dc levels of the input and output common-mode
voltages are different, matching errors will result in a small
differential-mode output offset voltage. For G = 1 case, with a
ground referenced input signal and the output common-mode
level set for 2.5 V, an output offset of as much as 25 mV (1% of
the difference in common-mode levels) can result if 1% tolerance resistors are used. Resistors of 1% tolerance will result in a
worst case input CMRR of about 40 dB, worst-case differential mode output offset of 25 mV due to 2.5 V level-shift, and
no significant degradation in output balance error.
Calculating an Application Circuit’s Input Impedance
The effective input impedance of a circuit such as that in Figure
2, at +DIN and –DIN, will depend on whether the amplifier is
being driven by a single-ended or differential signal source. For
balanced differential input signals, the input impedance (RIN,dm)
between the inputs (+DIN and –DIN) is simply:
RIN,dm = 2 × RG
In the case of a single-ended input signal (for example if –DIN is
grounded and the input signal is applied to +DIN), the input
impedance becomes:
RIN , dm


RG
= 
RF
1 −

2 × RG + RF

(
)
In cases where more accurate control of the output common-mode
level is required, it is recommended that an external source,
or resistor divider (made up of 10 kΩ resistors), be used. The
output common-mode offset specified on pages 2 and 3 assume
the VOCM input is driven by a low impedance voltage source.
Driving a Capacitive Load
A purely capacitive load can react with the pin and bondwire
inductance of the AD8138 resulting in high frequency ringing in
the pulse response. One way to minimize this effect is to place a
small capacitor across each of the feedback resistors. The added
capacitance should be small to avoid destabilizing the amplifier.
An alternative technique is to place a small resistor in series with
the amplifier’s outputs as shown in TPC 23.
LAYOUT, GROUNDING AND BYPASSING
As a high speed part, the AD8138 is sensitive to the PCB
environment in which it has to operate. Realizing its superior
specifications requires attention to various details of good high
speed PCB design.
The first requirement is for a good solid ground plane that covers as much of the board area around the AD8138 as possible.
The only exception to this is that the two input pins (Pins 1 and
8) should be kept a few mm from the ground plane, and ground
should be removed from inner layers and the opposite side of
the board under the input pins. This will minimize the stray
capacitance on these nodes and help preserve the gain flatness
versus frequency.
The power supply pins should be bypassed as close as possible
to the device to the nearby ground plane. Good high frequency
ceramic chip capacitors should be used. This bypassing should
be done with a capacitance value of 0.01 µF to 0.1 µF for
each supply. Further away, low frequency bypassing should
be provided with 10 µF tantalum capacitors from each supply
to ground.







The circuit’s input impedance is effectively higher than it would
be for a conventional op amp connected as an inverter because a
fraction of the differential output voltage appears at the inputs
as a common-mode signal, partially bootstrapping the voltage
across the input resistor RG.
Input Common-Mode Voltage Range in Single Supply
Applications
The AD8138 is optimized for level-shifting “ground” referenced
input signals. For a single-ended input this would imply, for
example, that the voltage at –DIN in Figure 1 would be zero
volts when the amplifier’s negative power supply voltage (at V–)
was also set to zero volts.
The signal routing should be short and direct in order to avoid
parasitic effects. Wherever there are complementary signals, a
symmetrical layout should be provided to the extent possible to
maximize the balance performance. When running differential
signals over a long distance, the traces on PCB should be close
together or any differential wiring should be twisted together
to minimize the area of the loop that is formed. This will
reduce the radiated energy and make the circuit less susceptible to interference.
–10–
REV. C
AD8138
BALANCED TRANSFORMER DRIVER
SIGNAL WILL BE COUPLED
ON THIS SIDE VIA CSTRAY
Transformers are among the oldest devices that have been used
to perform a single-ended-to-differential conversion (and vice
versa). Transformers also can perform the additional functions
of galvanic isolation, step-up or step-down of voltages and
impedance transformation. For these reasons, transformers will
always find uses in certain applications.
CSTRAY
VUNBAL
52.3⍀ PRIMARY
CSTRAY
However, when driving a transformer single-endedly and then
looking at its output, there is a fundamental imbalance due to
the parasitics inherent in the transformer. The primary (or
driven) side of the transformer has one side at dc potential
(usually ground), while the other side is driven. This can
cause problems in systems that require good balance of the
transformer’s differential output signals.
NO SIGNAL IS COUPLED
ON THIS SIDE
Figure 3. Transformer Single-Ended-to-Differential Converter Is Inherently Imbalanced
499⍀
If the interwinding capacitance (CSTRAY) is assumed to be uniformly distributed, a signal from the driving source will couple
to the secondary output terminal that is closest to the primary’s
driven side. On the other hand, no signal will be coupled to the
opposite terminal of the secondary, because its nearest primary
terminal is not driven. (See Figure 3.) The exact amount of this
imbalance will depend on the particular parasitics of the transformer, but will mostly be a problem at higher frequencies.
CSTRAY
49.9⍀
499⍀
+IN
OUT–
VUNBAL
AD8138
499⍀
500⍀
0.005%
VDIFF
500⍀
0.005%
OUT+
–IN
49.9⍀
CSTRAY
499⍀
The balance of a differential circuit can be measured by connecting
an equal-valued resistive voltage divider across the differential
outputs and then measuring the center point of the circuit with
respect ground. Since the two differential outputs are supposed
to be of equal amplitude, but 180 degrees opposite phase, there
should be no signal present for perfectly balanced outputs.
Figure 4. AD8138 Forms a Balanced Transformer Driver
0
OUTPUT BALANCE ERROR – dB
The circuit in Figure 3 shows a Minicircuits T1-6T transformer connected with its primary driven single-endedly and the
secondary connected with a precision voltage divider across its
terminals. The voltage divider is made up of two 500 Ω, 0.005%
precision resistors. The voltage VUNBAL, which is also equal to
the ac common-mode voltage, is a measure of how closely the
outputs are balanced.
The plots in Figure 5 show a comparison between the case
where the transformer is driven single-endedly by a signal generator and driven differentially using an AD8138. The top signal
trace of Figure 5 shows the balance of the single-ended configuration, while the bottom shows the differentially driven balance
response. The 100 MHz balance is 35 dB better when using
the AD8138.
–20
–40
VUNBAL, FOR TRANSFORMER
WITH SINGLE-ENDED DRIVE
–60
–80
VUNBAL, DIFFERENTIAL DRIVE
–100
0.3
The well-balanced outputs of the AD8138 will provide a drive
signal to each of the transformer’s primary inputs that are of
equal amplitude and 180 degrees out of phase. Thus, depending
on how the polarity of the secondary is connected, the signals
that conduct across the interwinding capacitance will either both
assist the transformer’s secondary signal equally, or both buck
the secondary signals. In either case, the parasitic effect will be
symmetrical and provide a well-balanced transformer output.
(See Figure 5.)
REV. C
500⍀
0.005%
500⍀ SECONDARY VDIFF
0.005%
1
10
FREQUENCY – MHz
100
500
Figure 5. Output Balance Error for Circuits of Figures 3
and 4
–11–
AD8138
HIGH-PERFORMANCE ADC DRIVING
The circuit in Figure 6 shows a simplified front-end connection
for an AD8138 driving an AD9224, a 12-bit, 40 MSPS A/D
converter. The A/D works best when driven differentially, which
minimizes its distortion as described in its data sheet. The
AD8138 eliminates the need for a transformer to drive the ADC
and performs single-ended-to-differential conversion, common-mode level-shifting and buffering of the driving signal.
The positive and negative outputs of the AD8138 are connected
to the respective differential inputs of the AD9224 via a pair of
49.9 Ω resistors to minimize the effects of the switched-capacitor
front-end of the AD9224. For best distortion performance it is
run from supplies of ± 5 V.
The AD8138 is configured with unity gain for a single-ended
input-to-differential output. The additional 23 Ω, 523 Ω total, at
the input to –IN is to balance the parallel impedance of the 50 Ω
source and its 50 Ω termination that drives the noninverting input.
The signal generator has a ground-referenced, bipolar output,
i.e., it drives symmetrically above and below ground. Connecting
VOCM to the CML pin of the AD9224 sets the output commonmode of the AD8138 at 2.5 V, which is the midsupply level for
the AD9224. This voltage is bypassed by a 0.1 µF capacitor.
The full-scale analog input range of the AD9224 is set to 4 V p-p,
by shorting the SENSE terminal to AVSS. This has been determined to be the scaling to provide minimum harmonic distortion.
For the AD8138 to swing a 4 V p-p, each output swings 2 V p-p,
while providing signals that are 180 degrees out of phase. With
a common-mode voltage at the output of 2.5 V, this means
that each AD8138 output will swing between 1.5 V and 3.5 V.
A ground-referenced 4 V p-p, 5 MHz signal at DIN+ was used
to test the circuit in Figure 6. When the combined-device
circuit was run with a sampling rate of 20 MHz MSPS, the
SFDR (spurious free dynamic range) was measured at –85 dBc.
+5V
+5V
0.1pF
499⍀
499⍀
50⍀
SOURCE
49.9⍀
+
VINB
0.1pF
AVDD DRVDD
VOCM
49.9⍀
523⍀
AD8138
DIGITAL
OUTPUTS
AD9224
49.9⍀
VINA AVSS
SENSE CML
DRVSS
0.1pF
499⍀
–5V
Figure 6. AD8138 Driving an AD9224, a 12-Bit, 40 MSPS A/D Converter
–12–
REV. C
AD8138
The circuit was tested with a –0.5 dBFS signal at various
frequencies. Figure 8 shows a plot of the total harmonic distortion (THD) vs. frequency at signal amplitudes of 1 V and 2 V
differential drive levels.
3 V OPERATION
The circuit in Figure 7 shows a simplified front end connection
for an AD8138 driving an AD9203, a 10-bit, 40 MSPS A/D
converter that is specified to work on a single 3 V supply. The
A/D works best when driven differentially to make the best use
of the signal swing available within the 3 V supply. The appropriate outputs of the AD8138 are connected to the appropriate
differential inputs of the AD9203 via a low-pass filter.
–40
–45
The AD8138 is configured for unity gain for a single-ended
input to differential output. The additional 23 Ω at the input to
–IN is to balance the impedance of the 50 Ω source and its 50 Ω
termination that drives the noninverting input.
THD – dBc
–50
The signal generator has ground-referenced, bipolar output,
i.e., it can drive symmetrically above and below ground. Even
though the AD8138 has ground as its negative supply, it can
still function as a level-shifter with such an input signal.
AD8138-2V
–60
–65
AD8138-1V
–70
–75
The output common-mode is raised up to midsupply by the
voltage divider that biases VOCM. In this way, the AD8138 provides dc-coupling and level-shifting of a bipolar signal, without
inverting the input signal.
–80
0
5
10
15
FREQUENCY – MHz
20
25
Figure 8. AD9203 THD @ –0.5 dBFS AD8138
The low-pass filter between the AD8138 and the AD9203
provides filtering that helps to improve the signal-to-noise
ratio. Lower noise can be realized by lowering the pole frequency, but the bandwidth of the circuit will be lowered.
+3V
–55
Figure 9 shows the signal to noise plus distortion (SINAD)
under the same conditions as above. For the smaller signal swing,
the AD8138 performance is quite good, but its performance
degrades when trying to swing too close to the supply rails.
+3V
0.1␮F
499⍀
65
0.1␮F
0.1␮F
63
10k⍀
61
49.9⍀
49.9⍀
+
AD8138
523⍀
20pF
49.9⍀
AVDD
AINN
DRVDD
AD9203
AINP
DIGITAL
OUTPUTS
AVSS DRVSS
20pF
0.1␮F
499⍀
59
SINAD – dBc
499⍀
57
AD8138-1V
55
AD8138-2V
53
10k⍀
51
49
Figure 7. AD8138 Driving an AD9203, a 10-Bit, 40 MSPS
A/D Converter
47
45
0
5
10
15
FREQUENCY – MHz
20
25
Figure 9. AD9203 SINAD @ –0.5 dBFS AD8138
REV. C
–13–
AD8138
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead SOIC
(SO-8)
0.1968 (5.00)
0.1890 (4.80)
0.1574 (4.00)
0.1497 (3.80)
8
5
1
4
PIN 1
0.0098 (0.25)
0.0040 (0.10)
0.2440 (6.20)
0.2284 (5.80)
0.0688 (1.75)
0.0532 (1.35)
0.0196 (0.50)
x 45°
0.0099 (0.25)
0.0500 0.0192 (0.49)
SEATING (1.27)
0.0098 (0.25)
PLANE BSC 0.0138 (0.35) 0.0075 (0.19)
8°
0° 0.0500 (1.27)
0.0160 (0.41)
8-Lead MICRO_SOIC
(RM-8)
0.122 (3.10)
0.114 (2.90)
8
5
0.199 (5.05)
0.187 (4.75)
0.122 (3.10)
0.114 (2.90)
1
4
PIN 1
0.0256 (0.65) BSC
0.120 (3.05)
0.112 (2.84)
0.006 (0.15)
0.002 (0.05)
0.018 (0.46)
SEATING 0.008 (0.20)
PLANE
0.120 (3.05)
0.112 (2.84)
0.043 (1.09)
0.037 (0.94)
0.011 (0.28)
0.003 (0.08)
33ⴗ
27ⴗ
0.028 (0.71)
0.016 (0.41)
AD8138–Revision History
Location
Page
Data Sheet changed from REV. B to REV. C.
Edits to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
–14–
REV. C
–15–
–16–
PRINTED IN U.S.A.
C01073–0–6/01(C)