PDF Data Sheet Rev. H

Low Cost Low Power
Instrumentation Amplifier
AD620
FEATURES
CONNECTION DIAGRAM
Weigh scales
ECG and medical instrumentation
Transducer interface
Data acquisition systems
Industrial process controls
Battery-powered and portable equipment
–IN
2
7 +VS
+IN
3
6
–VS
4
AD620
RG
OUTPUT
5 REF
Figure 1. 8-Lead PDIP (N), CERDIP (Q), and SOIC (R) Packages
PRODUCT DESCRIPTION
The AD620 is a low cost, high accuracy instrumentation
amplifier that requires only one external resistor to set gains of
1 to 10,000. Furthermore, the AD620 features 8-lead SOIC and
DIP packaging that is smaller than discrete designs and offers
lower power (only 1.3 mA max supply current), making it a
good fit for battery-powered, portable (or remote) applications.
The AD620, with its high accuracy of 40 ppm maximum
nonlinearity, low offset voltage of 50 μV max, and offset drift of
0.6 μV/°C max, is ideal for use in precision data acquisition
systems, such as weigh scales and transducer interfaces.
Furthermore, the low noise, low input bias current, and low power
of the AD620 make it well suited for medical applications, such
as ECG and noninvasive blood pressure monitors.
The low input bias current of 1.0 nA max is made possible with
the use of Superϐeta processing in the input stage. The AD620
works well as a preamplifier due to its low input voltage noise of
9 nV/√Hz at 1 kHz, 0.28 μV p-p in the 0.1 Hz to 10 Hz band,
and 0.1 pA/√Hz input current noise. Also, the AD620 is well
suited for multiplexed applications with its settling time of 15 μs
to 0.01%, and its cost is low enough to enable designs with one
in-amp per channel.
30,000
TOTAL ERROR, PPM OF FULL SCALE
Comment
Better specs at lower price
Dual channel or differential out
Low power, wide input range
JFET input
Best gain accuracy
+2 precision op amps or differential out
Ultra low noise
8
TOP VIEW
Table 1. Next Generation Upgrades for AD620
Part
AD8221
AD8222
AD8226
AD8220
AD8228
AD8295
AD8429
1
25,000
3 OP AMP
IN-AMP
(3 OP-07s)
20,000
15,000
AD620A
10,000
RG
5,000
0
0
5
10
SUPPLY CURRENT (mA)
15
20
00775-0-002
APPLICATIONS
RG
00775-0-001
Easy to use
Gain set with one external resistor
(Gain range 1 to 10,000)
Wide power supply range (±2.3 V to ±18 V)
Higher performance than 3 op amp IA designs
Available in 8-lead DIP and SOIC packaging
Low power, 1.3 mA max supply current
Excellent dc performance (B grade)
50 μV max, input offset voltage
0.6 μV/°C max, input offset drift
1.0 nA max, input bias current
100 dB min common-mode rejection ratio (G = 10)
Low noise
9 nV/√Hz @ 1 kHz, input voltage noise
0.28 μV p-p noise (0.1 Hz to 10 Hz)
Excellent ac specifications
120 kHz bandwidth (G = 100)
15 μs settling time to 0.01%
Figure 2. Three Op Amp IA Designs vs. AD620
Rev. H
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.326.8703© 2003–2011 Analog Devices, Inc. All rights reserved.
AD620
TABLE OF CONTENTS
Specifications .....................................................................................3 RF Interference............................................................................15 Absolute Maximum Ratings ............................................................5 Common-Mode Rejection.........................................................16 ESD Caution ..................................................................................5 Grounding....................................................................................16 Typical Performance Characteristics..............................................6 Ground Returns for Input Bias Currents.................................17 Theory of Operation .......................................................................12 AD620ACHIPS Information .........................................................18 Gain Selection..............................................................................15 Outline Dimensions........................................................................19 Input and Output Offset Voltage ..............................................15 Ordering Guide ...........................................................................20 Reference Terminal .....................................................................15 Input Protection ..........................................................................15 REVISION HISTORY
7/11—Rev. G to Rev. H
Changes to Input Protection section ............................................15
Deleted Figure 3.................................................................................1
Deleted Figure 9 ..............................................................................15
Added Table 1 ....................................................................................1
Changes to RF Interference section..............................................15
Moved Figure 2 ..................................................................................1
Edit to Ground Returns for Input Bias Currents section...........17
Added ESD Input Diodes to Simplified Schematic ....................12
Added AD620CHIPS to Ordering Guide ....................................19
Changes to Input Protection Section............................................15
Added Figure 41; Renumbered Sequentially ...............................15
7/03—Data Sheet Changed from Rev. E to Rev. F
Changes to AD620ACHIPS Information Section ......................18
Edit to FEATURES............................................................................1
Updated Ordering Guide ...............................................................20
Changes to SPECIFICATIONS .......................................................2
Removed AD620CHIPS from ORDERING GUIDE ...................4
Removed METALLIZATION PHOTOGRAPH...........................4
12/04—Rev. F to Rev. G
Updated Format.................................................................. Universal
Change to Features............................................................................1
Change to Product Description.......................................................1
Changes to Specifications.................................................................3
Added Metallization Photograph....................................................4
Replaced Figure 4-Figure 6 ..............................................................6
Replaced Figure 15 ............................................................................7
Replaced Figure 33 ..........................................................................10
Replaced Figure 34 and Figure 35.................................................10
Replaced Figure 37 ..........................................................................10
Changes to Table 3 ..........................................................................13
Replaced TPCs 1–3 ...........................................................................5
Replaced TPC 12 ...............................................................................6
Replaced TPC 30 ...............................................................................9
Replaced TPCs 31 and 32...............................................................10
Replaced Figure 4 ............................................................................10
Changes to Table I...........................................................................11
Changes to Figures 6 and 7 ............................................................12
Changes to Figure 8 ........................................................................13
Edited INPUT PROTECTION section........................................13
Added new Figure 9........................................................................13
Changes to RF INTERFACE section ............................................14
Changes to Figure 41 and Figure 42 .............................................14
Edit to GROUND RETURNS FOR INPUT BIAS CURRENTS
section...............................................................................................15
Changes to Figure 43 ......................................................................15
Updated OUTLINE DIMENSIONS .............................................16
Change to Figure 44 ........................................................................17
Rev. H | Page 2 of 20
AD620
SPECIFICATIONS
Typical @ 25°C, VS = ±15 V, and RL = 2 kΩ, unless otherwise noted.
Table 2.
AD620A
Parameter
GAIN
Gain Range
Gain Error2
G=1
G = 10
G = 100
G = 1000
Nonlinearity
G = 1–1000
G = 1–100
Gain vs. Temperature
VOLTAGE OFFSET
Input Offset, VOSI
Overtemperature
Average TC
Output Offset, VOSO
Overtemperature
Average TC
Offset Referred to the
Input vs. Supply (PSR)
G=1
G = 10
G = 100
G = 1000
INPUT CURRENT
Input Bias Current
Overtemperature
Average TC
Input Offset Current
Overtemperature
Average TC
INPUT
Input Impedance
Differential
Common-Mode
Input Voltage Range3
Overtemperature
Overtemperature
Conditions Min
G = 1 + (49.4 kΩ/RG)
1
VOUT = ±10 V
VOUT = −10 V to +10 V
RL = 10 kΩ
RL = 2 kΩ
Typ
AD620B
Max
Min
10,000
1
Typ
Max
Min
10,000
1
AD620S1
Typ Max
Unit
10,000
0.03
0.15
0.15
0.40
0.10
0.30
0.30
0.70
0.01
0.10
0.10
0.35
0.02
0.15
0.15
0.50
0.03
0.15
0.15
0.40
0.10
0.30
0.30
0.70
%
%
%
%
10
10
40
95
10
10
40
95
10
10
40
95
ppm
ppm
10
−50
ppm/°C
ppm/°C
125
μV
225
μV
G=1
Gain >12
(Total RTI Error = VOSI + VOSO/G)
VS = ±5 V
30
to ± 15 V
VS = ±5 V
to ± 15 V
VS = ±5 V
0.3
to ± 15 V
VS = ±15 V
400
VS = ± 5 V
VS = ±5 V
to ± 15 V
VS = ±5 V
5.0
to ± 15 V
10
−50
10
−50
125
15
185
50
30
85
1.0
0.1
0.6
0.3
1.0
μV/°C
1000
1500
2000
200
500
750
1000
400
1000
1500
2000
μV
μV
μV
15
2.5
7.0
5.0
15
μV/°C
VS = ±2.3 V
to ±18 V
80
95
110
110
100
120
140
140
0.5
3.0
0.3
VS = ±2.3 V −VS + 1.9
to ±5 V
−VS + 2.1
VS = ± 5 V
−VS + 1.9
to ±18 V
−VS + 2.1
80
100
120
120
2.0
2.5
100
120
140
140
0.5
3.0
0.3
1.0
1.5
80
95
110
110
1.0
1.5
100
120
140
140
0.5
8.0
0.3
0.5
0.75
1.5
1.5
8.0
10||2
10||2
10||2
10||2
10||2
10||2
dB
dB
dB
dB
2
4
1.0
2.0
nA
nA
pA/°C
nA
nA
pA/°C
+VS − 1.2
−VS + 1.9
+VS − 1.2
−VS + 1.9
+VS − 1.2
GΩ_pF
GΩ_pF
V
+VS − 1.3
+VS − 1.4
−VS + 2.1
−VS + 1.9
+VS − 1.3
+VS − 1.4
−VS + 2.1
−VS + 1.9
+VS − 1.3
+VS − 1.4
V
V
+VS − 1.4
−VS + 2.1
+VS + 2.1
−VS + 2.3
+VS − 1.4
V
Rev. H | Page 3 of 20
AD620
AD620A
AD620B
Parameter
Conditions Min
Typ Max
Common-Mode Rejection
Ratio DC to 60 Hz with
1 kΩ Source Imbalance VCM = 0 V to ± 10 V
G=1
73
90
G = 10
93
110
G = 100
110
130
G = 1000
110
130
OUTPUT
Output Swing
RL = 10 kΩ
VS = ±2.3 V −VS +
+VS − 1.2
to ± 5 V
1.1
Overtemperature
−VS + 1.4
+VS − 1.3
VS = ±5 V
−VS + 1.2
+VS − 1.4
to ± 18 V
Overtemperature
−VS + 1.6
+VS – 1.5
Short Circuit Current
±18
DYNAMIC RESPONSE
Small Signal –3 dB Bandwidth
G=1
1000
G = 10
800
G = 100
120
G = 1000
12
Slew Rate
0.75
1.2
Settling Time to 0.01%
10 V Step
G = 1–100
15
G = 1000
150
NOISE
Voltage Noise, 1 kHz
Total RTI Noise = (e 2 ni ) + (e / G)2
Min
Typ
80
100
120
120
90
110
130
130
Max
Min
AD620S 1
Typ Max
73
93
110
110
90
110
130
130
Unit
dB
dB
dB
dB
−VS + 1.1
+VS − 1.2
−VS + 1.1
+VS − 1.2
V
−VS + 1.4
−VS + 1.2
+VS − 1.3
+VS − 1.4
−VS + 1.6
−VS + 1.2
+VS − 1.3
+VS − 1.4
V
V
+VS – 1.5
–VS + 2.3
+VS – 1.5
−VS + 1.6
0.75
±18
±18
V
mA
1000
800
120
12
1.2
1000
800
120
12
1.2
kHz
kHz
kHz
kHz
V/μs
15
150
μs
μs
0.75
15
150
no
Input, Voltage Noise, eni
Output, Voltage Noise, eno
RTI, 0.1 Hz to 10 Hz
G=1
G = 10
G = 100–1000
Current Noise
0.1 Hz to 10 Hz
REFERENCE INPUT
RIN
IIN
Voltage Range
Gain to Output
POWER SUPPLY
Operating Range 4
Quiescent Current
9
72
3.0
0.55
0.28
100
10
f = 1 kHz
20
50
VIN+, VREF = 0
−VS + 1.6
1 ± 0.0001
±2.3
VS = ±2.3 V
to ±18 V
Overtemperature
TEMPERATURE RANGE
For Specified Performance
13
100
60
+VS − 1.6
0.9
±18
1.3
1.1
1.6
−40 to +85
9
72
13
100
9
72
13
100
nV/√Hz
nV/√Hz
3.0
0.55
0.28
100
10
6.0
0.8
0.4
3.0
0.55
0.28
100
10
6.0
0.8
0.4
μV p-p
μV p-p
μV p-p
fA/√Hz
pA p-p
20
50
−VS + 1.6
1 ± 0.0001
±2.3
−40 to +85
1
See Analog Devices military data sheet for 883B tested specifications.
Does not include effects of external resistor RG.
3
One input grounded. G = 1.
4
This is defined as the same supply range that is used to specify PSR.
2
Rev. H | Page 4 of 20
60
+VS − 1.6
0.9
±18
1.3
1.1
1.6
20
50
60
+VS − 1.6
kΩ
μA
V
0.9
±18
1.3
V
mA
1.1
1.6
mA
−VS + 1.6
1 ± 0.0001
±2.3
−55 to +125
°C
AD620
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
Supply Voltage
Internal Power Dissipation 1
Input Voltage (Common-Mode)
Differential Input Voltage
Output Short-Circuit Duration
Storage Temperature Range (Q)
Storage Temperature Range (N, R)
Operating Temperature Range
AD620 (A, B)
AD620 (S)
Lead Temperature Range
(Soldering 10 seconds)
1
Rating
±18 V
650 mW
±VS
25 V
Indefinite
−65°C to +150°C
−65°C to +125°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other condition s above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
−40°C to +85°C
−55°C to +125°C
ESD CAUTION
300°C
Specification is for device in free air:
8-Lead Plastic Package: θJA = 95°C
8-Lead CERDIP Package: θJA = 110°C
8-Lead SOIC Package: θJA = 155°C
Rev. H | Page 5 of 20
AD620
TYPICAL PERFORMANCE CHARACTERISTICS
(@ 25°C, VS = ±15 V, RL = 2 kΩ, unless otherwise noted.)
2.0
50
SAMPLE SIZE = 360
1.5
INPUT BIAS CURRENT (nA)
PERCENTAGE OF UNITS
40
30
20
10
1.0
+IB
–I B
0.5
0
–0.5
–1.0
–40
0
40
80
INPUT OFFSET VOLTAGE (μV)
–2.0
–75
–25
25
75
TEMPERATURE (°C)
125
175
00775-0-008
–80
00775-0-005
0
5
00775-0-009
–1.5
Figure 6. Input Bias Current vs. Temperature
Figure 3. Typical Distribution of Input Offset Voltage
2.0
50
CHANGE IN OFFSET VOLTAGE (μV)
SAMPLE SIZE = 850
PERCENTAGE OF UNITS
40
30
20
0
–1200
–600
0
600
1200
INPUT BIAS CURRENT (pA)
00775-0-006
10
1.5
1.0
0.5
0
0
1
2
3
WARM-UP TIME (Minutes)
4
Figure 7. Change in Input Offset Voltage vs. Warm-Up Time
Figure 4. Typical Distribution of Input Bias Current
1000
50
SAMPLE SIZE = 850
GAIN = 1
VOLTAGE NOISE (nV/ Hz)
30
20
10
100
GAIN = 10
10
GAIN = 100, 1,000
0
–400
–200
0
200
400
INPUT OFFSET CURRENT (pA)
1
1
Figure 5. Typical Distribution of Input Offset Current
10
100
1k
FREQUENCY (Hz)
10k
100k
00775-0-010
GAIN = 1000
BW LIMIT
00775-0-007
PERCENTAGE OF UNITS
40
Figure 8. Voltage Noise Spectral Density vs. Frequency (G = 1−1000)
Rev. H | Page 6 of 20
AD620
10
1
10
100
FREQUENCY (Hz)
1000
00775-0-014
100
00775-0-011
CURRENT NOISE (fA/ Hz)
1000
Figure 12. 0.1 Hz to 10 Hz Current Noise, 5 pA/Div
Figure 9. Current Noise Spectral Density vs. Frequency
TOTAL DRIFT FROM 25°C TO 85°C, RTI (μV)
10,000
FET INPUT
IN-AMP
1000
AD620A
100
10
1k
10k
100k
1M
SOURCE RESISTANCE (Ω)
10M
00775-0-015
TIME (1 SEC/DIV)
00775-0-012
RTI NOISE (2.0μV/DIV)
100,000
Figure 13. Total Drift vs. Source Resistance
Figure 10. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1)
160
140
RTI NOISE (0.1μV/DIV)
120
CMR (dB)
100
G = 1000
G = 100
G = 10
G=1
80
60
40
Figure 11. 0.1 Hz to 10 Hz RTI Voltage Noise (G = 1000)
0
0.1
1
10
100
1k
FREQUENCY (Hz)
10k
100k
1M
00775-0-016
00775-0-013
TIME (1 SEC/DIV)
20
Figure 14. Typical CMR vs. Frequency, RTI, Zero to 1 kΩ Source Imbalance
Rev. H | Page 7 of 20
AD620
180
35
160
30
G = 100
80
G = 10
60
G=1
10
1
100
1k
FREQUENCY (Hz)
10k
100k
10
1M
0
G = 1000
1k
10k
100k
FREQUENCY (Hz)
Figure 15. Positive PSR vs. Frequency, RTI (G = 1−1000)
160
–0.5
INPUT VOLTAGE LIMIT (V)
(REFERRED TO SUPPLY VOLTAGES)
+VS –0.0
140
PSR (dB)
120
G = 1000
80
G = 100
60
G = 10
G=1
1
10
100
1k
FREQUENCY (Hz)
10k
100k
1M
00775-0-018
40
20
0.1
–1.5
+1.5
+1.0
+0.5
0
5
10
15
SUPPLY VOLTAGE ± Volts
20
20
Figure 19. Input Voltage Range vs. Supply Voltage, G = 1
1000
OUTPUT VOLTAGE SWING (V)
(REFERRED TO SUPPLY VOLTAGES)
+VS –0.0
100
10
1
1k
10k
100k
FREQUENCY (Hz)
1M
10M
00775-0-019
GAIN (V/V)
–1.0
–VS +0.0
Figure 16. Negative PSR vs. Frequency, RTI (G = 1−1000)
0.1
100
1M
Figure 18. Large Signal Frequency Response
180
100
G = 100
00775-0-021
20
0.1
15
5
00775-0-017
40
G=1
20
00775-0-022
PSR (dB)
100
25
00775-0-020
G = 1000
120
BW LIMIT
140
OUTPUT VOLTAGE (V p-p)
G = 10, 100, 1000
–0.5
RL = 10kΩ
–1.0
RL = 2kΩ
–1.5
+1.5
RL = 2kΩ
+1.0
RL = 10kΩ
+0.5
–VS +0.0
0
5
10
15
SUPPLY VOLTAGE ± Volts
Figure 20. Output Voltage Swing vs. Supply Voltage, G = 10
Figure 17. Gain vs. Frequency
Rev. H | Page 8 of 20
AD620
.... .... .... .... .... .... .... .... .... ....
VS = ±15V
G = 10
20
10
0
100
1k
LOAD RESISTANCE (Ω)
10k
Figure 21. Output Voltage Swing vs. Load Resistance
00775-0-023
0
00775-0-026
.... .... .... .... .... .... .... .... .... ....
Figure 24. Large Signal Response and Settling Time, G = 10 (0.5 mV = 0.01%)
.... .... .... .... .... .... .... .... .... ....
.... .... .... .... .... .... .... .... .... ....
.... .... .... .... .... .... .... .... .... ....
00775-0-027
00775-0-024
.... .... .... .... .... .... .... .... .... ....
Figure 22. Large Signal Pulse Response and Settling Time
G = 1 (0.5 mV = 0.01%)
Figure 25. Small Signal Response, G = 10, RL = 2 kΩ, CL = 100 pF
.... .... .... .... .... .... .... .... .... ....
.... .... .... .... .... .... .... .... .... ....
.... .... .... .... .... .... .... .... .... ....
.... .... .... .... .... .... .... .... .... ....
Figure 23. Small Signal Response, G = 1, RL = 2 kΩ, CL = 100 pF
00775-0-030
00775-0-025
OUTPUT VOLTAGE SWING (V p-p)
30
Figure 26. Large Signal Response and Settling Time, G = 100 (0.5 mV = 0.01%)
Rev. H | Page 9 of 20
AD620
20
.... .... .... .... .... .... .... .... ........
SETTLING TIME (μs)
15
TO 0.01%
TO 0.1%
10
0
5
10
OUTPUT STEP SIZE (V)
20
00775-0-032
00775-0-029
0
1000
00775-0-033
5
.... .... .... .... .... .... .... .... ........
15
Figure 30. Settling Time vs. Step Size (G = 1)
Figure 27. Small Signal Pulse Response, G = 100, RL = 2 kΩ, CL = 100 pF
1000
SETTLING TIME (μs)
.... .... .... .... .... .... .... .... .... ....
100
10
00775-0-030
.... .... .... .... .... .... .... .... .... ....
1
1
10
100
GAIN
Figure 28. Large Signal Response and Settling Time,
G = 1000 (0.5 mV = 0.01% )
Figure 31. Settling Time to 0.01% vs. Gain, for a 10 V Step
.... .... .... .... .... .... .... .... .... ....
.... .... .... .... .... .... .... .... ........
.... .... .... .... .... .... .... .... .... ....
00775-0-031
00775-0-034
.... .... .... .... .... .... .... .... ........
Figure 29. Small Signal Pulse Response, G = 1000, RL = 2 kΩ, CL = 100 pF
Rev. H | Page 10 of 20
Figure 32. Gain Nonlinearity, G = 1, RL = 10 kΩ (10 μV = 1 ppm)
AD620
10kΩ *
INPUT
10V p-p
.... .... .... .... .... .... .... .... ........
1kΩ
10T
10kΩ
100k Ω
VOUT
+VS
1kΩ
2
100 Ω
7
1
G = 1000
G=1
AD620
G = 100 G = 10
.... .... .... .... .... .... .... .... ........
49.9Ω
499 Ω
5.49k Ω
00775-0-035
8
3
5
4
–VS
*ALL RESISTORS 1% TOLERANCE
Figure 33. Gain Nonlinearity, G = 100, RL = 10 kΩ
(100 μV = 10 ppm)
Figure 35. Settling Time Test Circuit
.... .... .... .... .... .... .... .... ........
00775-0-036
.... .... .... .... .... .... .... .... ........
Figure 34. Gain Nonlinearity, G = 1000, RL = 10 kΩ
(1 mV = 100 ppm)
Rev. H | Page 11 of 20
6
00775-0-037
11kΩ
AD620
THEORY OF OPERATION
The input transistors Q1 and Q2 provide a single differentialpair bipolar input for high precision (Figure 36), yet offer 10×
lower input bias current thanks to Superϐeta processing.
Feedback through the Q1-A1-R1 loop and the Q2-A2-R2 loop
maintains constant collector current of the input devices Q1
and Q2, thereby impressing the input voltage across the external
gain setting resistor RG. This creates a differential gain from the
inputs to the A1/A2 outputs given by G = (R1 + R2)/RG + 1. The
unity-gain subtractor, A3, removes any common-mode signal,
yielding a single-ended output referred to the REF pin potential.
+VS
VB
20µA
I2
20µA
A1
A2
10kΩ
C2
C1
10kΩ
OUTPUT
A3
10kΩ
+VS
R3
400Ω
REF
+VS
R1
– IN
10kΩ
R2
Q1
Q2
RG
GAIN
SENSE
R4
400Ω
+IN
GAIN
SENSE
–VS
00775-0-038
I1
Figure 36. Simplified Schematic of AD620
The AD620 is a monolithic instrumentation amplifier based on
a modification of the classic three op amp approach. Absolute
value trimming allows the user to program gain accurately
(to 0.15% at G = 100) with only one resistor. Monolithic
construction and laser wafer trimming allow the tight matching
and tracking of circuit components, thus ensuring the high level
of performance inherent in this circuit.
The value of RG also determines the transconductance of the
preamp stage. As RG is reduced for larger gains, the
transconductance increases asymptotically to that of the input
transistors. This has three important advantages: (a) Open-loop
gain is boosted for increasing programmed gain, thus reducing
gain related errors. (b) The gain-bandwidth product
(determined by C1 and C2 and the preamp transconductance)
increases with programmed gain, thus optimizing frequency
response. (c) The input voltage noise is reduced to a value of
9 nV/√Hz, determined mainly by the collector current and base
resistance of the input devices.
The internal gain resistors, R1 and R2, are trimmed to an
absolute value of 24.7 kΩ, allowing the gain to be programmed
accurately with a single external resistor.
The gain equation is then
G=
49.4 kΩ
RG =
RG
+1
49.4 kΩ
G−1
Make vs. Buy: a Typical Bridge Application Error Budget
The AD620 offers improved performance over “homebrew”
three op amp IA designs, along with smaller size, fewer
components, and 10× lower supply current. In the typical
application, shown in Figure 37, a gain of 100 is required to
amplify a bridge output of 20 mV full-scale over the industrial
temperature range of −40°C to +85°C. Table 4 shows how to
calculate the effect various error sources have on circuit
accuracy.
Rev. H | Page 12 of 20
AD620
Note that for the homebrew circuit, the OP07 specifications for
input voltage offset and noise have been multiplied by √2. This
is because a three op amp type in-amp has two op amps at its
inputs, both contributing to the overall input error.
Regardless of the system in which it is being used, the AD620
provides greater accuracy at low power and price. In simple
systems, absolute accuracy and drift errors are by far the most
significant contributors to error. In more complex systems
with an intelligent processor, an autogain/autozero cycle
removes all absolute accuracy and drift errors, leaving only the
resolution errors of gain, nonlinearity, and noise, thus allowing
full 14-bit accuracy.
10V
R = 350Ω
00775-0-039
PRECISION BRIDGE TRANSDUCER
AD620A MONOLITHIC
INSTRUMENTATION
AMPLIFIER, G = 100
SUPPLY CURRENT = 1.3mA MAX
100Ω **
OP07D
10kΩ **
OP07D
00775-0-040
R = 350Ω
10kΩ *
10kΩ **
REFERENCE
R = 350Ω
10kΩ *
OP07D
AD620A
10kΩ *
10kΩ*
"HOMEBREW" IN-AMP, G = 100
*0.02% RESISTOR MATCH, 3ppm/°C TRACKING
**DISCRETE 1% RESISTOR, 100ppm/ °C TRACKING
SUPPLY CURRENT = 15mA MAX
Figure 37. Make vs. Buy
Table 4. Make vs. Buy Error Budget
Error Source
ABSOLUTE ACCURACY at TA = 25°C
Input Offset Voltage, μV
Output Offset Voltage, μV
Input Offset Current, nA
CMR, dB
DRIFT TO 85°C
Gain Drift, ppm/°C
Input Offset Voltage Drift, μV/°C
Output Offset Voltage Drift, μV/°C
RESOLUTION
Gain Nonlinearity, ppm of Full Scale
Typ 0.1 Hz to 10 Hz Voltage Noise, μV p-p
Error, ppm of Full Scale
AD620
Homebrew
AD620 Circuit Calculation
“Homebrew” Circuit Calculation
125 μV/20 mV
1000 μV/100 mV/20 mV
2 nA ×350 Ω/20 mV
110 dB(3.16 ppm) ×5 V/20 mV
(150 μV × √2)/20 mV
((150 μV × 2)/100)/20 mV
(6 nA ×350 Ω)/20 mV
(0.02% Match × 5 V)/20 mV/100
6,250
500
18
791
10,607
150
53
500
Total Absolute Error
7,559
11,310
100 ppm/°C Track × 60°C
(2.5 μV/°C × √2 × 60°C)/20 mV
(2.5 μV/°C × 2 × 60°C)/100 mV/20 mV
3,600
3,000
450
6,000
10,607
150
Total Drift Error
7,050
16,757
40
14
54
14,663
40
27
67
28,134
(50 ppm + 10 ppm) ×60°C
1 μV/°C × 60°C/20 mV
15 μV/°C × 60°C/100 mV/20 mV
40 ppm
0.28 μV p-p/20 mV
40 ppm
(0.38 μV p-p × √2)/20 mV
Total Resolution Error
Grand Total Error
G = 100, VS = ±15 V.
(All errors are min/max and referred to input.)
Rev. H | Page 13 of 20
00775-0-041
R = 350Ω
RG
499Ω
AD620
5V
3kΩ
3kΩ
3kΩ
3kΩ
20kΩ
7
3
REF
8
AD620B
G = 100
499Ω
6
5
1
IN
10kΩ
ADC
4
2
20kΩ
1.7mA
AD705
AGND
0.6mA
MAX
0.10mA
00775-0-042
1.3mA
MAX
DIGITAL
DATA
OUTPUT
Figure 38. A Pressure Monitor Circuit that Operates on a 5 V Single Supply
Pressure Measurement
Medical ECG
Although useful in many bridge applications, such as weigh
scales, the AD620 is especially suitable for higher resistance
pressure sensors powered at lower voltages where small size and
low power become more significant.
The low current noise of the AD620 allows its use in ECG
monitors (Figure 39) where high source resistances of 1 MΩ or
higher are not uncommon. The AD620’s low power, low supply
voltage requirements, and space-saving 8-lead mini-DIP and
SOIC package offerings make it an excellent choice for batterypowered data recorders.
Figure 38 shows a 3 kΩ pressure transducer bridge powered
from 5 V. In such a circuit, the bridge consumes only 1.7 mA.
Adding the AD620 and a buffered voltage divider allows the
signal to be conditioned for only 3.8 mA of total supply current.
Small size and low cost make the AD620 especially attractive for
voltage output pressure transducers. Since it delivers low noise
and drift, it also serves applications such as diagnostic
noninvasive blood pressure measurement.
R1
10kΩ
R4
1MΩ
The value of capacitor C1 is chosen to maintain stability of
the right leg drive loop. Proper safeguards, such as isolation,
must be added to this circuit to protect the patient from
possible harm.
+3V
PATIENT/CIRCUIT
PROTECTION/ISOLATION
C1
Furthermore, the low bias currents and low current noise,
coupled with the low voltage noise of the AD620, improve the
dynamic range for better performance.
R3
24.9kΩ
R2
24.9kΩ
RG
8.25kΩ
AD620A
G=7
0.03Hz
HIGHPASS
FILTER
G = 143
OUTPUT
1V/mV
OUTPUT
AMPLIFIER
–3V
Figure 39. A Medical ECG Monitor Circuit
Rev. H | Page 14 of 20
00775-0-043
AD705J
AD620
Precision V-I Converter
INPUT AND OUTPUT OFFSET VOLTAGE
The AD620, along with another op amp and two resistors,
makes a precision current source (Figure 40). The op amp
buffers the reference terminal to maintain good CMR. The
output voltage, VX, of the AD620 appears across R1, which
converts it to a current. This current, less only the input bias
current of the op amp, then flows out to the load.
The low errors of the AD620 are attributed to two sources,
input and output errors. The output error is divided by G when
referred to the input. In practice, the input errors dominate at
high gains, and the output errors dominate at low gains. The
total VOS for a given gain is calculated as
Total Error RTI = input error + (output error/G)
+VS
Total Error RTO = (input error × G) + output error
7
3
8
1
VIN–
6
The reference terminal potential defines the zero output voltage
and is especially useful when the load does not share a precise
ground with the rest of the system. It provides a direct means of
injecting a precise offset to the output, with an allowable range
of 2 V within the supply voltages. Parasitic resistance should be
kept to a minimum for optimum CMR.
R1
5
2
4
IL
–VS
I L=
REFERENCE TERMINAL
+ VX –
AD620
RG
Vx
R1
=
AD705
[(V IN+) – (V IN– )] G
R1
LOAD
00775-0-044
VIN+
Figure 40. Precision Voltage-to-Current Converter (Operates on 1.8 mA, ±3 V)
GAIN SELECTION
The AD620 gain is resistor-programmed by RG, or more
precisely, by whatever impedance appears between Pins 1 and 8.
The AD620 is designed to offer accurate gains using 0.1% to 1%
resistors. Table 5 shows required values of RG for various gains.
Note that for G = 1, the RG pins are unconnected (RG = ∞). For
any arbitrary gain, RG can be calculated by using the formula:
RG =
49.4 kΩ
G −1
INPUT PROTECTION
The AD620 safely withstands an input current of ±60 mA for
several hours at room temperature. This is true for all gains and
power on and off, which is useful if the signal source and
amplifier are powered separately. For longer time periods, the
input current should not exceed 6 mA.
For input voltages beyond the supplies, a protection resistor
should be placed in series with each input to limit the current to
6 mA. These can be the same resistors as those used in the RFI
filter. High values of resistance can impact the noise and AC
CMRR performance of the system. Low leakage diodes (such as
the BAV199) can be placed at the inputs to reduce the required
protection resistance.
+SUPPLY
To minimize gain error, avoid high parasitic resistance in series
with RG; to minimize gain drift, RG should have a low TC—less
than 10 ppm/°C—for the best performance.
R
+IN
Table 5. Required Values of Gain Resistors
Calculated
Gain
1.990
4.984
9.998
19.93
50.40
100.0
199.4
495.0
991.0
0.1% Std Table
Value of RG(Ω )
49.3 k
12.4 k
5.49 k
2.61 k
1.01 k
499
249
98.8
49.3
Calculated
Gain
2.002
4.984
9.998
19.93
49.91
100.0
199.4
501.0
1,003.0
VOUT
AD620
R
REF
–IN
–SUPPLY
00775-0-052
1% Std Table
Value of RG(Ω)
49.9 k
12.4 k
5.49 k
2.61 k
1.00 k
499
249
100
49.9
Figure 41. Diode Protection for Voltages Beyond Supply
RF INTERFERENCE
All instrumentation amplifiers rectify small out of band signals.
The disturbance may appear as a small dc voltage offset. High
frequency signals can be filtered with a low pass R-C network
placed at the input of the instrumentation amplifier. Figure 42
demonstrates such a configuration. The filter limits the input
Rev. H | Page 15 of 20
AD620
signal according to the following relationship:
+VS
– INPUT
FilterFreq DIFF =
FilterFreq CM =
1
2πR(2C D + C C )
100Ω
1
2πRC C
AD648
RG
100Ω
AD620
VOUT
–VS
REFERENCE
00775-0-046
where CD ≥10CC.
+ INPUT
CD affects the difference signal. CC affects the common-mode
signal. Any mismatch in R × CC degrades the AD620 CMRR. To
avoid inadvertently reducing CMRR-bandwidth performance,
make sure that CC is at least one magnitude smaller than CD.
The effect of mismatched CCs is reduced with a larger CD:CC
ratio.
–VS
Figure 43. Differential Shield Driver
+VS
– INPUT
+15V
R
CC
CD
CC
+IN
–IN
RG
2
AD620
VOUT
REFERENCE
+
+ INPUT
AD620
499Ω
RG
2
AD548
–
00775-0-047
R
100Ω
10μ F
0.1μ F
VOUT
–VS
REF
Figure 44. Common-Mode Shield Driver
Since the AD620 output voltage is developed with respect to the
potential on the reference terminal, it can solve many
grounding problems by simply tying the REF pin to the
appropriate “local ground.”
Figure 42. Circuit to Attenuate RF Interference
COMMON-MODE REJECTION
Instrumentation amplifiers, such as the AD620, offer high
CMR, which is a measure of the change in output voltage when
both inputs are changed by equal amounts. These specifications
are usually given for a full-range input voltage change and a
specified source imbalance.
For optimal CMR, the reference terminal should be tied to a
low impedance point, and differences in capacitance and
resistance should be kept to a minimum between the two
inputs. In many applications, shielded cables are used to
minimize noise; for best CMR over frequency, the shield
should be properly driven. Figure 43 and Figure 44 show active
data guards that are configured to improve ac common-mode
rejections by “bootstrapping” the capacitances of input cable
shields, thus minimizing the capacitance mismatch between the
inputs.
To isolate low level analog signals from a noisy digital
environment, many data-acquisition components have separate
analog and digital ground pins (Figure 45). It would be
convenient to use a single ground line; however, current
through ground wires and PC runs of the circuit card can cause
hundreds of millivolts of error. Therefore, separate ground
returns should be provided to minimize the current flow from
the sensitive points to the system ground. These ground returns
must be tied together at some point, usually best at the ADC
package shown in Figure 45.
ANALOG P.S.
+15V C –15V
0.1μ F
0.1μ F
DIGITAL P.S.
C +5V
1μ F 1μ F
1μ F
+
AD620
AD585
S/H
AD574A
ADC
Figure 45. Basic Grounding Practice
Rev. H | Page 16 of 20
DIGITAL
DATA
OUTPUT
00775-0-048
–15V
00775-0-045
GROUNDING
10μ F
0.1μ F
AD620
+VS
GROUND RETURNS FOR INPUT BIAS CURRENTS
– INPUT
Input bias currents are those currents necessary to bias the
input transistors of an amplifier. There must be a direct return
path for these currents. Therefore, when amplifying “floating”
input sources, such as transformers or ac-coupled sources, there
must be a dc path from each input to ground, as shown in
Figure 46, Figure 47, and Figure 48. Refer to A Designer’s Guide
to Instrumentation Amplifiers (free from Analog Devices) for
more information regarding in-amp applications.
AD620
RG
VOUT
LOAD
REFERENCE
+ INPUT
TO POWER
SUPPLY
GROUND
+VS
– INPUT
00775-0-050
–VS
Figure 47. Ground Returns for Bias Currents with Thermocouple Inputs
RG
AD620
VOUT
+VS
– INPUT
LOAD
+ INPUT
REFERENCE
–VS
VOUT
LOAD
REFERENCE
+ INPUT
Figure 46. Ground Returns for Bias Currents with Transformer-Coupled Inputs
100k Ω
100kΩ
–VS
TO POWER
SUPPLY
GROUND
Figure 48. Ground Returns for Bias Currents with AC-Coupled Inputs
Rev. H | Page 17 of 20
00775-0-051
TO POWER
SUPPLY
GROUND
AD620
00775-0-049
RG
AD620
AD620ACHIPS INFORMATION
Die size: 1803 μm × 3175 μm
Die thickness: 483 μm
Bond Pad Metal: 1% Copper Doped Aluminum
To minimize gain errors introduced by the bond wires, use Kelvin connections between the chip and the gain resistor, RG, by connecting
Pad 1A and Pad 1B in parallel to one end of RG and Pad 8A and Pad 8B in parallel to the other end of RG. For unity gain applications
where RG is not required, Pad 1A and Pad 1B must be bonded together as well as the Pad 8A and Pad 8B.
1A
8A
LOGO
1B
2
8B
7
6
4
5
00775-0-053
3
Figure 49. Bond Pad Diagram
Table 6. Bond Pad Information
Pad No.
1A
1B
2
3
4
5
6
7
8A
8B
1
Mnemonic
RG
RG
−IN
+IN
−VS
REF
OUTPUT
+VS
RG
RG
Pad Coordinates 1
Y (μm)
+1424
+628
+453
−294
−1419
−1429
−1254
+139
+1423
+372
X (μm)
−623
−789
−790
−790
−788
+570
+693
+693
+505
+693
The pad coordinates indicate the center of each pad, referenced to the center of the die. The die orientation is indicated by the logo, as shown in Figure 49.
Rev. H | Page 18 of 20
AD620
OUTLINE DIMENSIONS
0.400 (10.16)
0.365 (9.27)
0.355 (9.02)
5
1
4
5.00 (0.1968)
4.80 (0.1890)
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.060 (1.52)
MAX
0.210 (5.33)
MAX
0.015
(0.38)
MIN
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
4.00 (0.1574)
3.80 (0.1497)
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.015 (0.38)
GAUGE
PLANE
0.430 (10.92)
MAX
0.005 (0.13)
MIN
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
8
070606-A
0.055 (1.40)
MAX
5
0.310 (7.87)
0.220 (5.59)
1
4
0.100 (2.54) BSC
0.320 (8.13)
0.290 (7.37)
0.405 (10.29) MAX
0.060 (1.52)
0.015 (0.38)
0.200 (5.08)
MAX
0.150 (3.81)
MIN
0.200 (5.08)
0.125 (3.18)
0.023 (0.58)
0.014 (0.36)
0.070 (1.78)
0.030 (0.76)
SEATING
PLANE
15°
0°
4
6.20 (0.2441)
5.80 (0.2284)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0196)
0.25 (0.0099)
0.015 (0.38)
0.008 (0.20)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 51. 8-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-8)
Dimensions shown in inches and (millimeters)
Rev. H | Page 19 of 20
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 50. 8-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body (N-8).
Dimensions shown in inches and (millimeters)
0.005 (0.13)
MIN
5
1.27 (0.0500)
BSC
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
8
1
Figure 52. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body (R-8)
Dimensions shown in millimeters and (inches)
012407-A
8
AD620
ORDERING GUIDE
Model1
AD620AN
AD620ANZ
AD620BN
AD620BNZ
AD620AR
AD620ARZ
AD620AR-REEL
AD620ARZ-REEL
AD620AR-REEL7
AD620ARZ-REEL7
AD620BR
AD620BRZ
AD620BR-REEL
AD620BRZ-RL
AD620BR-REEL7
AD620BRZ-R7
AD620ACHIPS
AD620SQ/883B
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−55°C to +125°C
Package Description
8-Lead PDIP
8-Lead PDIP
8-Lead PDIP
8-Lead PDIP
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 13" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
8-Lead SOIC_N, 7" Tape and Reel
Die Form
8-Lead CERDIP
Z = RoHS Compliant Part.
© 2003–2011 Analog Devices, Inc. All rights reserved. Trademarks
and registered trademarks are the property of their respective owners.
C00775–0–7/11(H)
Rev. H | Page 20 of 20
Package Option
N-8
N-8
N-8
N-8
R-8
R-8
R-8
R-8
R-8
R-8
R-8
R-8
R-8
R-8
R-8
R-8
Q-8