MBRS1540T3 Surface Mount Schottky Power Rectifier SMB Power Surface Mount Package These devices employ the Schottky Barrier principle in a metal−to−silicon power rectifier. Features epitaxial construction with oxide passivation and metal overlay contact. Ideally suited for low voltage, high frequency switching power supplies; free wheeling diodes and polarity protection diodes. Features • • • • • http://onsemi.com SCHOTTKY BARRIER RECTIFIER 1.5 AMPERES, 40 VOLTS Compact Package with J−Bend Leads Ideal for Automated Handling Highly Stable Oxide Passivated Junction Guard−Ring for Over−Voltage Protection Low Forward Voltage Drop Pb−Free Package is Available SMB CASE 403A PLASTIC Mechanical Characteristics • • • • • • Case: Molded Epoxy Epoxy Meets UL 94 V−0 @ 0.125 in Weight: 95 mg (Approximately) Cathode Polarity Band Lead and Mounting Surface Temperature for Soldering Purposes: 260°C Max. for 10 Seconds Finish: All External Surfaces Corrosion Resistant and Terminal Leads are Readily Solderable MARKING DIAGRAM AYWW BGJG G MAXIMUM RATINGS Rating Symbol Value Unit Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage VRRM VRWM VR 40 V Average Rectified Forward Current (At Rated VR, TC = 100°C) IO 1.5 A Peak Repetitive Forward Current (At Rated VR, Square Wave, 100 kHz, TC = 105°C) IFRM 3.0 A Non−Repetitive Peak Surge Current (Surge Applied at Rated Load Conditions Halfwave, Single Phase, 60 Hz) IFSM Storage/Operating Case Temperature Operating Junction Temperature Voltage Rate of Change (Rated VR, TJ = 25°C) ORDERING INFORMATION 40 A Tstg, TC −55 to +150 °C TJ −55 to +125 °C dv/dt 10,000 V/ms Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. © Semiconductor Components Industries, LLC, 2005 August, 2005 − Rev. 3 BGJ = Specific Device Code A = Assembly Location Y = Year WW = Work Week G = Pb−Free Package (Note: Microdot may be in either location) 1 Device Package Shipping † MBRS1540T3 SMB 2500/Tape & Reel SMB (Pb−Free) 2500/Tape & Reel MBRS1540T3G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. Publication Order Number: MBRS1540T3/D MBRS1540T3 THERMAL CHARACTERISTICS Characteristic Symbol Value Unit °C/W Thermal Resistance, Junction−to−Lead (Note 1) Thermal Resistance, Junction−to−Ambient (Note 2) RqJL 24 RqJA 80 ELECTRICAL CHARACTERISTICS vF Maximum Instantaneous Forward Voltage (Note 3) see Figure 2 (iF = 1.5 A) (iF = 3.0 A) IR Maximum Instantaneous Reverse Current (Note 3) see Figure 4 (VR = 40 V) (VR = 20 V) 1. Mounted with minimum recommended pad size, PC Board FR4. 2. 1 inch square pad size (1 x 0.5 inch for each lead) on FR4 board. 3. Pulse Test: Pulse Width ≤ 250 ms, Duty Cycle ≤ 2.0%. http://onsemi.com 2 TJ = 25°C TJ = 125°C 0.46 0.54 0.39 0.54 TJ = 25°C TJ = 100°C 0.8 0.1 5.7 1.6 V mA 100 IF, INSTANTANEOUS FORWARD CURRENT (AMPS) i F, INSTANTANEOUS FORWARD CURRENT (AMPS) MBRS1540T3 10 TJ = 125°C 25°C 1.0 100°C −40 °C 0.1 0.1 0.3 0.5 0.7 0.9 100°C 25°C 0.1 0.3 0.1 0.5 0.9 0.7 Figure 1. Typical Forward Voltage Figure 2. Maximum Forward Voltage 100E−3 10E−3 IR , MAXIMUM REVERSE CURRENT (AMPS) IR , REVERSE CURRENT (AMPS) TJ = 125°C 1.0 VF, MAXIMUM INSTANTANEOUS FORWARD VOLTAGE (VOLTS) TJ = 125°C 1.0E−3 100°C 100E−6 10E−3 TJ = 125°C 1.0E−3 100°C 100E−6 10E−6 25°C 10 0 20 30 40 1.0E−6 0 10 20 30 40 VR, REVERSE VOLTAGE (VOLTS) VR, REVERSE VOLTAGE (VOLTS) Figure 3. Typical Reverse Current Figure 4. Maximum Reverse Current 2.5 FREQ = 20 kHz dc 2.0 SQUARE WAVE 1.5 Ipk/Io = p Ipk/Io = 5.0 1.0 Ipk/Io = 10 Ipk/Io = 20 0.5 0 25 25°C 10E−6 PFO , AVERAGE POWER DISSIPATION (WATTS) IO , AVERAGE FORWARD CURRENT (AMPS) 10 vF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 100E−3 1.0E−6 100 45 65 85 105 125 1.2 dc 1.0 SQUARE WAVE Ipk/Io = p 0.8 Ipk/Io = 5.0 0.6 Ipk/Io = 10 0.4 Ipk/Io = 20 0.2 0 0 0.5 1.0 1.5 2.0 TL, LEAD TEMPERATURE (°C) IO, AVERAGE FORWARD CURRENT (AMPS) Figure 5. Current Derating Figure 6. Forward Power Dissipation http://onsemi.com 3 2.5 MBRS1540T3 TJ , DERATED OPERATING TEMPERATURE (° C) 1000 C, CAPACITANCE (pF) TJ = 25°C 100 10 R T, TRANSIENT THERMAL RESISTANCE (NORMALIZED) 0 5.0 10 15 20 25 30 35 40 125 Rtja = 24°C/W 115 43°C/W 105 63°C/W 95 80°C/W 85 93°C/W 75 65 0 5.0 10 15 20 25 30 35 40 VR, REVERSE VOLTAGE (VOLTS) VR, DC REVERSE VOLTAGE (VOLTS) Figure 7. Capacitance Figure 8. Typical Operating Temperature Derating* * Reverse power dissipation and the possibility of thermal runaway must be considered when operating this device under any reverse voltage conditions. Calculations of TJ therefore must include forward and reverse power effects. The allowable operating TJ may be calculated from the equation: TJ = TJmax − r(t)(Pf + Pr) where r(t) = thermal impedance under given conditions, Pf = forward power dissipation, and Pr = reverse power dissipation This graph displays the derated allowable TJ due to reverse bias under DC conditions only and is calculated as TJ = TJmax − r(t)Pr, where r(t) = Rthja. For other power applications further calculations must be performed. 1.0E+00 50% 1.0E−01 20% 10% 5.0% 1.0E−02 2.0% 1.0% 1.0E−03 Rtjl(t) = Rtjl*r(t) 1.0E−04 0.00001 0.0001 0.001 0.01 0.1 1.0 10 100 1000 10 100 1000 R T, TRANSIENT THERMAL RESISTANCE (NORMALIZED) t, TIME (s) 1.0E+00 1.0E−01 Figure 9. Thermal Response — Junction to Case 50% 20% 10% 5.0% 1.0E−02 2.0% 1.0E−03 1.0% Rtjl(t) = Rtjl*r(t) 1.0E−04 0.00001 0.0001 0.001 0.01 0.1 1.0 t, TIME (s) Figure 10. Thermal Response — Junction to Ambient http://onsemi.com 4 MBRS1540T3 PACKAGE DIMENSIONS SMB PLASTIC PACKAGE CASE 403A−03 ISSUE E NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. D DIMENSION SHALL BE MEASURED WITHIN DIMENSION P. HE E b DIM A A1 b c D E HE L L1 D MIN 1.90 0.05 1.96 0.15 3.30 4.06 5.21 0.76 MILLIMETERS NOM MAX 2.13 2.41 0.10 0.15 2.03 2.11 0.23 0.30 3.56 3.81 4.32 4.57 5.44 5.59 1.02 1.27 0.51 REF MIN 0.075 0.002 0.077 0.006 0.130 0.160 0.205 0.030 INCHES NOM 0.084 0.004 0.080 0.009 0.140 0.170 0.214 0.040 0.020 REF MAX 0.095 0.006 0.083 0.012 0.150 0.180 0.220 0.050 A L L1 A1 c SOLDERING FOOTPRINT* 2.261 0.089 2.743 0.108 2.159 0.085 SCALE 8:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Phone: 81−3−5773−3850 Email: [email protected] http://onsemi.com 5 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. MBRS1540T3/D