© Siemens AG 2016 Flow Measurement SITRANS F US Inline Flowmeter SONO 3100/FUS060 ■ Overview ■ Design The SONO 3100 in combination with FUS060 consists of a SONO 3100 sensor, SONO 3200 transducers with O-rings or flanges depending on selection - and a FUS060 transmitter. SONO 3100 is basically supplied in a 2-path solution with flanges in sizes from DN 100 to DN 600 and without flanges in sizes from DN 100 to DN 300. 1-path or 4-path special versions are available on request, depending on size (DN 25 to DN 1200). SONO 3100 is as standard available in carbon steel from DN 100 to DN 600. FUS060 is designed for remote wall mounting only. 3 ■ Technical specifications The transmitter related to this system is the SITRANS FUS060. Technical specifications to the FUS060 see page 3/247. 2-path sensor fitted with four SONO 3200 transducers Error in measurement The combination of the SONO 3100 sensor and the FUS060 transmitter is ideal for applications where process shut-down is impossible during service and where there is a need for extreme high/low temperatures and pressures. Transducers can be changed without interrupting operation. SONO 3100 can optionally be delivered as a 4-path solution for absolute best performance and accuracy. ■ Benefits • Transducers can be replaced under pressure • Measurement of all liquids less than 350 Cst, conductive or non-conductive • No pressure drop • Reliable and accurate flow measurements • Long-time stability • On request as special versions: - Special sensor material, e.g. Duplex, stainless steel - High/low temperature sensor version: +250 °C (+482 °F)/ -200 °C (-328 °F) sensors - Pressure rating 430 bar (6235 psi) - Special sensor sizes down to DN 25 - 1-path or 4-path sensor technology Error in measurement at reference conditions v > 0.5 ... 10 m/s, < 0.5 % of rate (v=flow velocity) Max flow velocity 10 m/s (32 ft/s) Nominal size DN 100 ... 600 (4" ... 24") Media temperature • Standard -10 ... +200 °C (14 ... 392 °F) • ATEX Ex d version -20 ... +200 °C (-4 … +392 °F) • ATEX Ex i version -10 ... +200 °C (14 ... +392 °F) • Specials -200 °C (-328 °F) or up to 250 °C (482 °F) Ambient temperature • Standard and Ex-i version -20 ... +180 °C (-4 ... +356 °F) Enclosure IP67 (NEMA 4X/6)/IP68 (NEMA 6P) and ATEX (see below) Process connections PN designated, EN 1092-1, type 11 (B) Pipe material carbon steel ■ Application The main application for SONO 3100 in combination with transmitter type FUS060 is to measure volume flow within: • Petrochemical industry • Power engineering • Water and waste water • Oil and liquefied gases SITRANS FUS060 holds ATEX for hazardous areas, HART and PROFIBUS PA. SONO 3100 holds ATEX Ex approval. Class designated, EN 1759-1 Pipe material carbon steel Siemens FI 01 · 2016 • DN 200 ... 600 (8" ... 24"), PN 10 • DN 100 ... 600 (4" ... 24"), PN 16 • DN 200 ... 600 (8" ... 24"), PN 25 • DN 100 ... 500 (4" ... 20"), PN 40 • DN 100 … 600 (4" … 24") Class 150 • DN 100 … 300 (4" … 12") Class 300 Without flanges (EN 10217), (weld-in version) only in carbon steel • DN 350 … 600 (14" … 24"), PN 10 • DN 100 … 600 (4" … 24"), PN 16 • DN 200 … 600 (8" … 24"), PN 25 • DN 100 … 500 (4" … 20"), PN 40 Transducer SONO 3200 O-ring or flange versions Materials Pipe Flange PN Class Transducer body Transducer terminal house 3/266 -20 ... +60 °C (-4 ... +140 °F) • Ex d version Steel EN 1.0345-P235GH EN 10025-S235JRG2, 1E1 ASTM A105,1,1 Stainless steel AISI 316 or similar Stainless steel AISI 316 or plastic PA 6.6 © Siemens AG 2016 Flow Measurement SITRANS F US Inline Flowmeter SONO 3100/FUS060 Certificates and approvals System ATEX approval for SONO 3100 together with transmitter FUS060-Ex ATEX II 2G Ex dem [ia/ib] IIC T6/T4/T3 Gb or ATEX II 2G Ex d IIC T3-T6 Gb with SONO 3200 Exd transducers (for standard FUS060 transmitter, installed outside of Ex zone) For FUS060 Ex version the transducer cable length is restricted to 3 m (9.84 ft), in order to meet requirements for electrical immunity. Conformity certificate The devices are supplied as standard with a Siemens Certificate of Conformity on CD Material certificate Material certificate according to EN 10204-3.1 is optionally available NDT examination report Extended material certificate is optionally available Pressure certificate Pressure test according EN 1024-2.3 optionally available Calibration report A standard calibration report is shipped with each flowmeter. Optionally available: Extended accredited ISO/IEC 17025 calibration certificates Approvals No custody transfer approvals The sensor SONO 3100 with transmitter FUS060 conforms to Product Family Standard EN 61326/A3 appendix A (Title: Electrical Equipment for Measurement control and laboratory use – EMC requirements). The sensors are approved according to EU directive 2014/68/EU dated 27 June 2014 regarding fluid group 1, classified in category III. Design according to EN 13480 (PED Directive). The SONO 3100 as weld-in version does not include the flanges. Thus, it can neither be tested nor approved according to PED. After the installation, all installation-related activities (welding, pressure test etc.) are the responsibility of the customer. Selection and Ordering data Article No. Order code SITRANS F US SONO 3100 sensor 2-path 7 ME 3 1 0 0 7 77 7 7 - 7 7 7 7 7 7 7 Click on the Article No. for the online configuration in the PIA Life Cycle Portal. Diameter Qn setting [m3/h] DN 100 (4") DN 100 (4") DN 100 (4") 28 100 220 1N 1P 1R DN 125 (5") DN 125 (5") DN 125 (5") 44 150 350 1S 1T 1V DN 150 (6") DN 150 (6") DN 150 (6") 64 220 500 2A 2B 2D DN 200 (8") DN 200 (8") DN 200 (8") 110 380 900 2E 2F 2H DN 250 (10") DN 250 (10") DN 250 (10") 180 600 1300 2J 2K 2M DN 300 (12") DN 300 (12") DN 300 (12") 250 850 2000 2N 2P 2R DN 350 (14") DN 350 (14") DN 350 (14") 350 1000 28001) 2S 2T 2V DN 400 (16") DN 400 (16") DN 400 (16") 450 1300 3600 3A 3B 3D DN 500 (20") DN 500 (20") DN 500 (20") 1300 2200 42001) 3J 3K 3M DN 600 (24") DN 600 (24") DN 600 (24") 1300 3200 42001) 3S 3T 3V 3 Flange norm and pressure rating (All sizes are not available in all pressure ratings) EN 1092-1 PN 10 (DN 200 ... DN 600) PN 16 (DN 100 ... DN 600) PN 25 (DN 200 ... DN 600) PN 40 (DN 100 ... DN 500) B C D E ANSI B16.5 class 150 (DN 100 ... DN 600) class 300 (DN 100 ... DN 300) H J Pipe without flanges (EN 10217) (weld-in version)2) PN 10 (DN 200 ... DN 600) PN 16 (DN 100 ... DN 600) PN 25 (DN 200 ... DN 600) PN 40 (DN 100 ... DN 500) P Q R S Siemens FI 01 · 2016 3/267 © Siemens AG 2016 Flow Measurement SITRANS F US Inline Flowmeter SONO 3100/FUS060 Selection and Ordering data Article No. Order code Selection and Ordering data SITRANS F US SONO 3100 sensor 2-path 7 ME 3 1 0 0 - Additional information 7 77 7 7 - 7 7 7 7 7 7 7 Please add „-Z" to Article No. and specify Order code(s) and plain text. Pipe and flange material Carbon steel (DN 100 ... 1200) Calibration 1 Transducer type and approval 3 IP67 (NEMA 4X/6) PA housing, PN 40, O-ring, 50 mm, 100 °C (212 °F) (DN 100 ... 600) IP68 SS housing, PN 40, O-ring, 50 mm, 200 °C (392 °F) (DN 100 ... 600) IP68 SS housing, PN 40, O-ring, 50 mm, 180 °C (356 °F), Ex d ATEX approval (only with standard FUS060) (DN 100 ... 600) 1 IP67 (NEMA 4X/6) PA housing, PN 40, flange, 88 mm, 100 °C (212 °F) (DN 100 ... 300) IP68 SS housing, PN 40, flange, 88 mm, 200 °C (392 °F) (DN 100 ... 300) IP68 SS housing, PN 40, flange, 88 mm, 180 °C (356 °F), Ex d ATEX approval (only with standard FUS060) (DN 100 ... 300) 4 IP67 SS housing, PN 40, O-ring, 50 mm, 190 °C (374 °F), Ex i ATEX approval (only with FUS060 Ex-version) (DN 100 ... 600) IP67 SS housing, PN 40, flange, 88 mm, 190 °C (374 °F), Ex i ATEX approval (only with FUS060 Ex-version) (DN 100 ... 300) 7 Cable gland entries Cable glands M20 in transducers and in transmitter M25/20/16 x 1.5 Cable glands ½" NPT in transducers and in transmitter 2 3 5 8 2 D 0 1 2 3 4 x 60 m, max. 70 °C (158 °F) 4 x 90 m, max. 70 °C (158 °F) 4 x 120 m, max. 70 °C (158 °F) 4 5 6 4 x 3 m, high temp. max. 200 °C (392 °F), the only option for Ex i 4 x 15 m, high temp. max. 200 °C (392 °F) 7 8 Reduced Q value during calibration (Qn setting unchanged). For weld-in sensor versions according to EN 10217 (flangeless sensors 7ME3100-xxYxx-xxxx, Y = P, Q, R, S) the tube roundness shall be agreed by ordering (only if the factor of Du / Wxx > 100). 3/268 Siemens FI 01 · 2016 D20 Accredited Siemens ISO/IEC 17025 calibration for DN 200 to DN 600 with Qn as selected in diameter. Calibration certificate: 2 x 5 points in 5 %, 10 %, 25 %, 50 % and 100 % Qn (max. flow 2800 m3/h). D21 Accredited Siemens ISO/IEC 17025 calibration for DN 400 to DN 600 with Qn as selected in diameter. Calibration certificate: 2 x 5 points in 5 %, 10 %, 25 %, 50 % and 100 % Qn (max. flow 8000 m3/h). D22 F10 F11 F12 F21 Y17 Please use online Product selector to get latest updates. Product selector link: www.pia-portal.automation.siemens.com N P Q PROFIBUS PA, 1 pulse/frequency 2) Accredited Siemens ISO/IEC 17025 calibration for DN 100 to DN 200 with Qn as selected in diameter. Calibration certificate: 2 x 5 points in 5 %, 10 %, 25 %, 50 % and 100 % Qn (max. flow 630 m3/h). Stainless steel TAG plate (1 x 24 x 80 mm), wire fixed. Font size depends on text length: 8 mm for 1 ... 10 characters, 4 mm for 11 ... 20 characters (specify in plain text). 1 B C 1) Included Tag name plate FUS060 output module HART, 1 pulse output, 1 relay HART Ex, 1 pulse output, 1 relay Transducer coaxial cable 4 x 3 m, max. 70 °C (158 °F), the only option for Ex i 4 x 15 m, max. 70 °C (158 °F) 4 x 30 m, high temp. max. 200 °C (392 °F) 4 x 30 m, max. 70 °C (158 °F) Production calibration DN 100 ... DN 600 (with certificate) Material certificate EN 10204-3.1 EN 10204-3.1 and 100 % NDT on weldings, DN 100 ... DN 400 EN 10204-3.1 and 100 % NDT on weldings, DN 500 ... DN 600 Pressure certificate EN 10204-2.3 6 Transmitter version of SITRANS FUS060 IP65 (NEMA 4), 120/230 V AC IP65 (NEMA 4), 24 V AC/DC IP65 (NEMA 4), 24 V AC/DC ATEX Ex version Order code © Siemens AG 2016 Flow Measurement SITRANS F US Inline Flowmeter SONO 3100/FUS060 ■ Flowmeter SONO 3100 with FUS060 operating instructions, accessories and spare parts Operating instructions Description Article No. SITRANS FUS060 • English • German A5E01204521 A5E02123845 SITRANS F US SONO 3100 • English A5E00814513 This device is shipped with a Quick Start guide and a CD containing further SITRANS F US literature. All literature is available to download for free, in a range of languages, at www.siemens.com/processinstrumentation/documentation Accessories Description Article No. Potting kit for terminal box of SONO 3200 transducer for IP68/NEMA 6P (not for Ex sensors) FDK:085L2403 Description Transducer length Article No. Extraction tool for replacement of SONO 3200 O-ring transducers under pressure and for hot-tapping (working conditions: typically water, max. 40 bar and max. 60 °C (max. 580 psi and max. 140 °F)) 50 mm (1.97") transducers FDK:085B5331 3 Cable connection boxes (For the connection of individually transducer cables with the FUS060 transducer cables) Article No. Description Junction box for coaxial cable • IP65 metal box for 4 coaxial cables FDK:085B1361 • IP65 EEx e plastic box for 4 coaxial cables, no ATEX approval FDK:085B1363 Spare parts Transducer SONO 3200 spare parts, complete units Type Material Gasket Press. rating Terminal housing Approv. Temp. range [°C (°F)] Length mm (inch) Article No. O-ring 316 SS O-ring PN 40 Plastic, PA 6.6 M20 -20 ... +100 (-4 ... +212) 50 (1.97) FDK:085B5453 O-ring 316 SS O-ring PN 40 316 SS M20 -20 ... +200 (-4 ... +392) 50 (1.97) FDK:085B5450 O-ring 316 SS O-ring PN 40 316 SS M20 Ex d1) -20 ... +200 (-4 ... +392) 50 (1.97) FDK:085B5451 O-ring 316 SS O-ring PN 40 316 SS M20 Ex i2) -10 ... +200 (14 ... 392) 50 (1.97) A5E00836448 O-ring 316 SS O-ring PN 40 Plastic, PA 6.6 ½" NPT -20 ... +100 (-4 ... +212) 50 (1.97) A5E00839472 O-ring 316 SS O-ring PN 40 316 SS ½" NPT -20 ... +200 (-4 ... +392) 50 (1.97) A5E00839431 Flange 316 SS Graphite PN 40 Plastic, PA 6.6 M20 -20 ... +100 (-4 ... +212) 88 (3.47) FDK:085B5461 Flange 316 SS Graphite PN 40 316 SS M20 -20 ... +200 (-4 ... +392) 88 (3.47) FDK:085B5462 Flange 316 SS Graphite PN 40 316 SS M20 -20 ... +200 (-4 ... +392) 88 (3.47) FDK:085B5463 Ex d1) Flange 316 SS Graphite PN 40 316 SS M20 -10 ... +200 (14 ... +392) 88 (3.47) A5E00836465 Flange 316 SS Graphite PN 40 Plastic, PA 6.6 ½" NPT -20 ... +100 (-4 ... +212) 88 (3.47) A5E00839479 Flange 316 SS Graphite PN 40 316 SS ½" NPT -20 ... +200 (-4 ... +392) 88 (3.47) A5E00839440 Flange 316 SS Copper ring PN 40 316 SS PG13.5 (cryogenic version) -200 ... +100 (-328 ... +212) 88 (3.47) FDK:085B5416 Flat 316 SS flange Flat gasket PN 40 316 SS M20 (cryogenic version) -200 ... +100 (-328 ... +212) 88 (3.47) A5E02593524 -20 ... +180 (-4 ... +356) 88 (3.47) FDK:085B5464 -20 ... +200 (-4 ... +392) 88 (3.47) FDK:085B5465 Flange 316 SS Graphite PN 160 316 SS M20 Flange 316 SS Graphite PN 160 316 SS M20 Ex i 2) Ex d1) 1) ATEX (Ex) IIC 2G Ex d IIC T3-T6 Gb 2) For systems with FUS060 ATEX IIC 2G Ex dem [ia/ib] T6/T4/T3 Siemens FI 01 · 2016 3/269 © Siemens AG 2016 Flow Measurement SITRANS F US Inline Flowmeter SONO 3100/FUS060 Terminal housing for SONO 3200 sensor 3 Type Pressure rating Material Temp. range [°C (°F)] Article No. Terminal housing (M20 cable gland) N/A PA 6.6 -20 ... +100 (-4 ... +212) FDK:085B5501 Terminal housing (M20 cable gland) N/A ASTM 316 -20 ... +200 (-4 ... +392) FDK:085B5504 Terminal housing (½" NPT cable gland) N/A PA 6.6 -20 ... +100 (-4 ... +212) A5E00839460 Terminal housing (½" NPT cable gland) N/A ASTM 316 -20 ... +200 (-4 ... +392) A5E00839427 Ex d1) terminal housing (M20 cable gland) N/A ASTM 316 -20 ... +200 (-4 ... +392) FDK:085B5505 Ex i2) terminal housing (M20 cable gland) N/A ASTM 316 -10 ... +200 (14 ... 392) A5E00835255 1) ATEX (Ex) IIC 2G EEx d IIC T3 ... T6 2) For systems with FUS060 ATEX IIC 2G Ex dem [ia/ib] T6/T4/T3 SONO 3200 spare parts, transducer body without terminal housing, including insert Type Material Gasket Pressure rating Temp. range [°C (°F)] Length Article No. mm (inch) O-ring 316 SS O-ring PN 40 -20 ... +200 (-4 ... +392) 50 (1.97) FDK:085B1405 Flange 316 SS Graphite PN 40 -20 ... +200 (-4 ... +392) 88 (3.47) FDK:085B1464 Type Temp. range [°C (°F)] Length Article No. mm (inch) Insert -20 ... +200 (-4 ... +392) 50 (1.97) FDK:085B1411 Insert -20 ... +200 (-4 ... +392) 88 (3.47) FDK:085B1459 SONO 3200 spare parts, transducer insert Transducer SONO 3200 gaskets Type Pressure rating Material Temperature range [°C (°F)] Article No. Gasket O-ring (3 pcs. for o-ring transducers) PN 40 FKM -20 … +200 (-4 ... +392) FDK:085B1089 Gasket flange PN 40/160 Graphite -20 … +200 (-4 ... +392) FDK:085B1080 Gasket and 12 mm (0.47") bolts and nuts PN 40 for flange transducers (4 pcs.) AISI 316 or equal -20 … +200 (-4 ... +392) FDK:085B1083 Gasket and 16 mm (0.63") bolts and nuts PN 160 for flange transducers (4 pcs.) Graphite, 316 SS -20 … +200 (-4 ... +392) FDK:085B1084 Gasket for cryogenics transducer with flat flange (2 pcs.) Graphite/metal composite 3/270 Siemens FI 01 · 2016 PN 40 -200 … +100 (-328 ... +212) A5E02593522 © Siemens AG 2016 Flow Measurement SITRANS F US Inline Flowmeter SONO 3100/FUS060 SONO 3200 cable glands Type/description Temperature range [°C (°F)] black PA plastic, cable -20 ... 100 (-4 ... +212) Cables for SONO 3100 with FUS060 Appr. Article No. A5E02246304 Ø 5 ... 13 mm (1 pc.) Description Length m (ft) Article No. Coaxial cable for FUS060, (75 , max. 70 ºC (158 ºF), black PVC) (2 pcs.) 3 (9.84) A5E00875101 15 (49.21) A5E00861432 30 (98.43) A5E01278662 60 (196.85) A5E01278682 90 (295.28) A5E01278687 ½" NPT -20 ... 100 gray PA (-4 ... +212) plastic, cable Ø 5 ... 9 mm (1 pc.) A5E02246309 ½" NPT -40 ... 100 crome(-40 ... +212) plated brass, cable Ø 5 ... 9 mm (1 pc.) A5E02246258 M20 stain- -25 ... 200 Ex i less steel, (-13 ... +392) cable Ø 4 ... 6 mm (1 pc.) A5E02246194 M20 Stain- -60 ... 180 Ex d less steel, (-76 ... +356) cable Ø 5 ... 8 mm (1 pc.) A5E02246311 120 (393.7) A5E01278698 High temp. coaxial 3 (9.84) cable for FUS060; 15 (49.21) with 0.3 m brown PTFE high temp. 30 (98.43) transducer part, max. 200 °C (392 °F) and black PVC for remaining transmitter part with SMB plug, max. 70 ºC (158 ºF); (impedance 75 ) (2 pcs.) A5E00875105 SITRANS F US special coaxial cable sets for low temperature cryogenic systems, with SMB-plug for transmitter SITRANS FUS060, PTFE material, temp. -200 ... +200 °C (-328 ... .+392 °F), impedance 75 (2 pcs.) 10 (32.84) A5E02085593 15 (49.21) A5E03262088 30 (98.43) A5E02085644 3 A5E00861435 A5E01196952 40 (131.23) A5E02085649 ■ Schematics 1 Xi 4 Path 1 Sensor 1 4 1A 1A 2B 1B 2A 1 2B 4 Path 2 1A 1B 2A 2B Sensor 1 2A 4 Electrical connection of SITRANS FUS060 and SONO 3100 Siemens FI 01 · 2016 3/271 © Siemens AG 2016 Flow Measurement SITRANS F US Inline Flowmeter SONO 3100/FUS060 ■ Dimensional drawings of sensor SONO 3100 H B D10 ... D300 Du L10 ... L300 L 3 θ A** Sensor SONO 3100 with EN norm PN 10 DN PN 16 PN 25 PN 40 DU L1) 4) B 5) H W102) D10 L101) W162) D16 L161) W252) D25 L251) W402) D40 L401) [mm] [mm] [mm] [mm] [°] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] 100 114.3 860 305 453) 42.8 - - - 3.6 220 960 - - - 3.6 235 990 125 139.7 862 325 453) 64.5 - - - 4.0 250 970 - - - 4.0 270 990 150 168.3 862 350 453) 78.1 - - - 4.5 285 970 - - - 4.5 300 1010 200 219.1 668 430 453) 102.1 6.3 340 790 6.3 340 790 6.3 360 820 6.3 375 840 250 273.0 714 480 453) 127.6 6.3 395 850 6.3 405 850 7.1 425 890 7.1 450 920 300 323.9 607 525 453) 151.8 7.1 445 740 7.1 460 760 8.0 485 790 8.0 515 830 350 355.6 639 550 453) 166.4 8.0 505 770 8.0 520 800 8.0 555 840 8.8 580 880 400 406.4 703 600 453) 191.3 8.0 565 850 8.0 580 875 8.8 620 925 11.1 660 975 500 508.0 797 690 453) 241.1 7.1 670 950 8.0 715 980 10.0 730 1050 14.2 755 1080 600 610.0 912 705 60 7.1 780 1075 8.8 840 1105 11.0 845 1165 - - - 294.8 1) Length tolerance (mm): DN 100 +2/-3, DN 125 ... 200 +3/-4, DN 250 ... 400 +4/-5, DN 500 ...600 +5/-6 2) Wall thickness for pressure rates PN 6 ... 40. For weld-in sensor versions according EN10217 (flangeless sensors 7ME3100-xxYxx-xxxx, Y=P, Q, R, S ) the tube roundness shall be agreed by ordering (only if the factor of Du/Wxx > 100). 3) For all sensors with flange transducers path angle are 60º 4) L is the length of sensor versions without flanges (weld-in version) For weld-in sensor versions according to EN 10217 (flangeless sensors 7ME3100-xxYxx-xxxx, Y = P, Q, R, S) the tube roundness shall be agreed by ordering (only if the factor of Du/Wxx > 100). 5) B dimension value is an approximate information and may differ a little by flange pressure rate. A**) Space required for replacement of transducer min. 230 mm (9.1 inch). For replacement with special tool (extraction tool) see more information on page 3/269. SONO 3100, 2-path Nominal diam. Flange type - Weight [kg (lb)] DN PN 10 PN 16 PN 25 PN 40 100 (4") - 32 (70.5) - 35 (77.2) 125 (5") - 38 (83.8) - 44 (97.0) 150 (6") - 45 (99.2) - 52 (114.6) 200 (8") 59 (130.0) 58 (127.9) 70 (154.3) 79 (174.2) 250 (10") 73 (161.0) 75 (163.3) 96 (211.6) 117 (257.9) 300 (12") 83 (183.0) 92 (202.8) 114 (251.3) 151 (332.9) 350 (14") 98 (216.0) 113 (249.1) 145 (332.9) 191 (421.1) 400 (16") 119 (262.4) 141 (310.9) 191 (421.1) 275 (606.3) 500 (20") 153 (337.3) 207 (456.4) 284 (626.0) 379 (836.0) 600 (24") 193 (425.5) 276 (608.5) 363 (800.3) - Weight of system incl. process flanges and standard O-ring transducers. For sensors with flange transducer please add approx. 10 kg (22.05 lb). For SS terminal housings instead of the standard PA housing add approx. 5 kg (11.03 lb). 3/272 Siemens FI 01 · 2016 © Siemens AG 2016 Flow Measurement SITRANS F US Inline Flowmeter SONO 3100/FUS060 H B D10 ... D300 Du L10 ... L300 L θ 3 A** Sensor SONO 3100 with ANSI norm Class 150 Class 300 Size (DN) DU L1) 4) B 5) H W1502) D150 L1501) W3002) D300 L3001) inch (mm) [inch] [inch] [inch] [°] [inch] [inch] [inch] [inch] [inch] [inch] [inch] 4 (100) 33.86 12.01 453) 1.69 0.14 9.00 39.86 0.25 10.00 40.62 4.50 5 (125) 5.50 33.94 12.80 453) 2.54 0.15 10.00 40.94 0.27 11.00 41.70 6 (150) 6.63 33.94 13.78 453) 3.07 0.16 11.00 40.94 0.30 12.50 41.70 8 (200) 8.63 26.30 16.93 453) 4.02 0.16 13.50 34.30 0.29 15.00 35.06 10 (250) 10.75 28.11 18.90 453) 5.02 0.18 16.00 36.11 0.34 17.50 37.35 12 (300) 12.75 23.90 20.67 453) 5.98 0.20 19.00 32.90 0.39 20.50 34.14 14 (350) 14.00 25.16 21.65 453) 6.55 0.21 21.00 35.16 - - - 16 (400) 16.00 27.68 23.62 453) 7.53 0.22 23.50 33.74 - - - 9.49 0.26 27.50 42.76 - - - 11.61 0.30 32.00 47.91 - - - 20 (500) 20.00 31.38 27.17 453) 24 (600) 24.00 35.91 27.76 60 1) Length tolerance (mm): 4" +0.08"/-0.12" (+2/-3mm), 5" ... 8" +0.12"/ -0.16" (+3/-4mm), 10" to 16" +0.16"/-0.20" (+4/-5mm), 20" ... 24" +0.20"/ -0.24" (+5/-6mm) 2) Minimum wall thickness for pressure rates Class 150 or Class 300. For weld-in sensor versions according to EN 10217 (flangeless sensors 7ME3100-xxYxx-xxxx, Y = P, Q, R, S) the tube roundness shall be agreed by ordering (only if the factor of Du/Wxx > 100). 3) For all sensors with flange transducers path angle are 60º 4) L is the length of sensor versions without flanges (weld-in version) For weld-in sensor versions according to EN 10217 (flangeless sensors 7ME3100-xxYxx-xxxx, Y = P, Q, R, S) the tube roundness shall be agreed by ordering (only if the factor of Du/Wxx > 100). 5) B dimension value is an approximate information and may differ a little by flange pressure rate. A**) Space required for replacement of transducer min. 230 mm (9.1 inch). For replacement with special tool (extraction tool) see more information in „Sensor SONO 3100 accessories and spare parts" on page 3/269. Siemens FI 01 · 2016 3/273 © Siemens AG 2016 Flow Measurement SITRANS F US Inline Flowmeter SONO 3100/FUS060 Approximate weights for SONO 3100 sensor with ANSI B16.5 flanges 3 Nominal diameter Weight [kg (lb)]1) DN DN CL150 [inch] [mm] [kg] [lb] [kg] [lb] 4 100 32 70.5 35 77.2 5 125 38 83.8 44 97.0 6 150 45 99.2 52 114.6 8 200 58 127.9 79 174.2 10 250 75 165.3 117 257.9 12 300 92 202.8 151 332.9 14 350 113 249.1 - - 16 400 141 310.9 - - 20 500 207 456.4 - - 600 276 608.5 - - 24 1) CL300 Weight of system incl. process flanges and standard O-ring transducers. For sensors with flange transducer please add approx. 10 kg (22.05 lb). For SS terminal housings instead of the standard PA housing add approx. 5 kg (11.03 lb). 3/274 Siemens FI 01 · 2016