Download

Small-diameter Proximity Sensor
E2E
Ultra small size, but surprisingly easy
installation!
• With the addition of M4, 5.4-dia., 6.5-dia. size, unshielded,
pre-wired connector model, and connector model, a total of
108 model variations are available.
• High-speed response frequency stably detects moving
objects: 5 kHz max.
• Four indicator lamps for easier indicator positioning.
• Special mounting brackets reduce time and efforts for
installation.
• Protective Stainless-steel Spiral Tube against wire
breakage is available (M4, M5 only).
• Models also available with standard cables that are 5 m long
or with robot (bending-resistant) cables.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Refer to Safety Precautions on page 10.
Features
Lineup of global small-diameter types (3 dia., 4 dia., 5.4 dia., 6.5 dia., M4, M5)
• A lineup of unshielded models for long distance sensing is also available. Stable long distance sensing performance enables worry-free use
even when the work flow is unsteady.
Bright operation indicators make it easy to check
operation status
• Four indicator lamps in a 360 degree layout can be easily seen.
Environment friendly, low current consumption
only 2/3 that of previous models
• All have a current consumption of 10 mA max.
Protective Stainless-steel Spiral Tube against
wire breakage is available
• Lineup of protective tubes for M4 and M5 sizes. Reduces wire
breakage due to catching and shock.
High-speed response enables sharp detection timing
• 5 kHz response frequency max.
Protection circuits prevent failures due to wiring mistakes.
• Load short-circuit protection and output reverse polarity protection
circuits are incorporated.
1
E2E
E2E (Small Diameter) Model Number Legend
E2E- A B C D - E - F G - H
No.
A
B
Classification
Case material and shape
Size
C
Shielding
D
Sensing distance
E
Connecting method
F
G
H
Output specifications
Operation mode
Cable specifications
Code
Cable length
Meaning
C
Cylindrical
S
SUS, threaded
03
Outer diameter 3 mm
04
Outer diameter 4 mm
05
Threaded: Outer diameter 5 mm, Cylindrical: Outer diameter 5.4 mm
06
Outer diameter 6.5 mm
S
Shielded Models
N
Number
Unshielded Models
R8: 0.8 mm, 01: 1 mm, 12: 1.2 mm, 02: 2 mm, 03: 3 mm, 04: 4 mm
WC
PVC Pre-wired Model
MC
M8 Connector, 3-pin
CJ
M8 Pre-wired Connector, 3-pin
B
DC 3-wire PNP open-collector output
C
DC 3-wire NPN open-collector output
1
Normally open (NO)
2
Normally closed (NC)
Blank
Standard PVC cable
R
Blank
I
I
Number M
Robot (bending-resistant) PVC cable
Connector Models
Cable length (Unit: m)
(Applicable to Pre-wired Models 2M/5M and Pre-wired Connector Models 0.3M)
Note: The purpose of this model number legend is to provide understanding of the meaning of specifications from the model number.
Models are not available for all combinations of code numbers.
2
E2E
Ordering Information
Sensors
Shielded Models [Refer to Dimensions on page 12.]
Appearance
Sensing
distance
Connecting
method
4 dia.
0.8 mm
1.2 mm
PVC
(oil-resistant)
M8 Pre-wired
Connector
Models (0.3 m)
PVC
(oil-resistant)
NO
Pre-wired Models
(2 m)
PVC
(oil-resistant)
NO
M8 Pre-wired
Connector
Models (0.3 m)
PVC
(oil-resistant)
NO
M8 Connector
Models
5.4 dia.
6.5 dia.
1 mm
2 mm
M5
0.8 mm
1.2 mm
---
NC
NC
NC
NC
NO
Pre-wired Models
(2 m)
PVC
(oil-resistant)
Pre-wired Models
(2 m)
PVC
(oil-resistant)
NO
M8 Pre-wired
Connector
Models (0.3 m)
PVC
(oil-resistant)
NO
---
NC
NC
NC
NO
PVC
(oil-resistant)
NO
M8 Pre-wired
Connector
Models (0.3 m)
PVC
(oil-resistant)
NO
Pre-wired Models
(2 m)
PVC
(oil-resistant)
NO
M8 Pre-wired
Connector
Models (0.3 m)
PVC
(oil-resistant)
NO
---
NC
NC
NC
NC
NO
NC
Model
NPN output
PNP output
Brown: +V
Black: Output
Blue: 0 V
E2E-C03SR8-WC-C1 2M *1
E2E-C03SR8-WC-B1 2M *1
E2E-C03SR8-WC-C2 2M *1
E2E-C03SR8-WC-B2 2M *1
1: +V,
3: 0 V,
4: Control output
E2E-C03SR8-CJ-C1 0.3M
E2E-C03SR8-CJ-B1 0.3M
E2E-C03SR8-CJ-C2 0.3M
E2E-C03SR8-CJ-B2 0.3M
Brown: +V
Black: Output
Blue: 0 V
1: +V,
3: 0 V,
4: Control output
E2E-C04S12-WC-C1 2M *1 *2 *3
E2E-C04S12-WC-B1 2M *1 *2 *3
E2E-C04S12-WC-C2 2M *1 *2 *3
E2E-C04S12-WC-B2 2M *1 *2 *3
E2E-C04S12-CJ-C1 0.3M
E2E-C04S12-CJ-B1 0.3M
E2E-C04S12-CJ-C2 0.3M
E2E-C04S12-CJ-B2 0.3M
E2E-C04S12-MC-C1
E2E-C04S12-MC-B1
E2E-C04S12-MC-C2
E2E-C04S12-MC-B2
Brown: +V
Black: Output
Blue: 0 V
E2E-C05S01-WC-C1 2M *1 *2 *3
E2E-C05S01-WC-B1 2M *1 *2 *3
E2E-C05S01-WC-C2 2M *1 *2
E2E-C05S01-WC-B2 2M *1 *2
Brown: +V
Black: Output
Blue: 0 V
E2E-C06S02-WC-C1 2M *1 *2 *3
E2E-C06S02-WC-B1 2M *1 *2 *3
E2E-C06S02-WC-C2 2M *1 *2 *3
E2E-C06S02-WC-B2 2M *1 *2 *3
1: +V,
3: 0 V,
4: Control output
NC
Pre-wired Models
(2 m)
M8 Connector
Models
Wire color /
pin arrangement
NC
NO
M8 Connector
Models
M4
Operation
mode
NO
Pre-wired Models
(2 m)
3 dia.
Cable
specifications
Brown: +V
Black: Output
Blue: 0 V
1: +V,
3: 0 V,
4: Control output
Brown: +V
Black: Output
Blue: 0 V
1: +V,
3: 0 V,
4: Control output
E2E-C06S02-CJ-C1 0.3M
E2E-C06S02-CJ-B1 0.3M
E2E-C06S02-CJ-C2 0.3M
E2E-C06S02-CJ-B2 0.3M
E2E-C06S02-MC-C1
E2E-C06S02-MC-B1
E2E-C06S02-MC-C2
E2E-C06S02-MC-B2
E2E-S04SR8-WC-C1 2M *1
E2E-S04SR8-WC-B1 2M *1
E2E-S04SR8-WC-C2 2M *1
E2E-S04SR8-WC-B2 2M *1
E2E-S04SR8-CJ-C1 0.3M
E2E-S04SR8-CJ-B1 0.3M
E2E-S04SR8-CJ-C2 0.3M
E2E-S04SR8-CJ-B2 0.3M
E2E-S05S12-WC-C1 2M *1 *2 *3
E2E-S05S12-WC-B1 2M *1 *2 *3
E2E-S05S12-WC-C2 2M *1 *2 *3
E2E-S05S12-WC-B2 2M *1 *2 *3
E2E-S05S12-CJ-C1 0.3M
E2E-S05S12-CJ-B1 0.3M
E2E-S05S12-CJ-C2 0.3M
E2E-S05S12-CJ-B2 0.3M
E2E-S05S12-MC-C1
E2E-S05S12-MC-B1
E2E-S05S12-MC-C2
E2E-S05S12-MC-B2
*1. Models with 5-m cable length are also available with "5M" suffix. (Example: E2E-C04S12-WC-C1 5M)
*2. Models with robot (bending-resistant) cable are also available with "-R" in the model number. (Example: E2E-C04S12-WC-C1-R 2M)
*3. Models with 5-m robot (bending-resistant) cable are also available with "-R" and the "5M" suffix in the model number. (Example: E2E-C04S12WC-C1-R 5M)
3
E2E
Unshielded Models [Refer to Dimensions on page 13.]
Appearance
Sensing
distance
Connecting
method
4 dia.
2 mm
3 mm
PVC
(oil-resistant)
M8 Pre-wired
Connector
Models (0.3 m)
PVC
(oil-resistant)
NO
Pre-wired Models
(2 m)
PVC
(oil-resistant)
NO
PVC
(oil-resistant)
NO
M8 Pre-wired
Connector
Models (0.3 m)
M8 Connector
Models
Pre-wired Models
(2 m)
6.5 dia.
4 mm
M8 Pre-wired
Connector
Models (0.3 m)
M8 Connector
Models
M4
M5
2 mm
3 mm
Operation
mode
NO
Pre-wired Models
(2 m)
3 dia.
Cable
specifications
---
NC
NC
NC
NC
NO
NO
PVC
(oil-resistant)
NO
NC
NC
NO
PVC
(oil-resistant)
NO
M8 Pre-wired
Connector
Models (0.3 m)
PVC
(oil-resistant)
NO
Pre-wired Models
(2 m)
PVC
(oil-resistant)
NO
M8 Pre-wired
Connector
Models (0.3 m)
PVC
(oil-resistant)
NO
M8 Connector
Models
---
NC
NC
NC
NC
NO
NC
PNP output
E2E-C03N02-WC-C1 2M *1
E2E-C03N02-WC-B1 2M *1
E2E-C03N02-WC-C2 2M *1
E2E-C03N02-WC-B2 2M *1
1: +V,
3: 0 V,
4: Control output
E2E-C03N02-CJ-C1 0.3M
E2E-C03N02-CJ-B1 0.3M
E2E-C03N02-CJ-C2 0.3M
E2E-C03N02-CJ-B2 0.3M
Brown: +V
Black: Output
Blue: 0 V
E2E-C04N03-WC-C1 2M *1 *2
E2E-C04N03-WC-B1 2M *1 *2
E2E-C04N03-WC-C2 2M *1 *2
E2E-C04N03-WC-B2 2M *1 *2
1: +V,
3: 0 V,
4: Control output
Brown: +V
Black: Output
Blue: 0 V
1: +V,
3: 0 V,
4: Control output
NC
Pre-wired Models
(2 m)
Model
NPN output
Brown: +V
Black: Output
Blue: 0 V
NC
PVC
(oil-resistant)
---
Wire color /
pin arrangement
E2E-C04N03-CJ-C1 0.3M
E2E-C04N03-CJ-B1 0.3M
E2E-C04N03-CJ-C2 0.3M
E2E-C04N03-CJ-B2 0.3M
E2E-C04N03-MC-C1
E2E-C04N03-MC-B1
E2E-C04N03-MC-C2
E2E-C04N03-MC-B2
E2E-C06N04-WC-C1 2M *1 *2
E2E-C06N04-WC-B1 2M *1 *2
E2E-C06N04-WC-C2 2M *1 *2
E2E-C06N04-WC-B2 2M *1 *2
E2E-C06N04-CJ-C1 0.3M
E2E-C06N04-CJ-B1 0.3M
E2E-C06N04-CJ-C2 0.3M
E2E-C06N04-CJ-B2 0.3M
E2E-C06N04-MC-C1
E2E-C06N04-MC-B1
E2E-C06N04-MC-C2
E2E-C06N04-MC-B2
Brown: +V
Black: Output
Blue: 0 V
E2E-S04N02-WC-C1 2M *1
E2E-S04N02-WC-B1 2M *1
E2E-S04N02-WC-C2 2M *1
E2E-S04N02-WC-B2 2M *1
1: +V,
3: 0 V,
4: Control output
E2E-S04N02-CJ-C1 0.3M
E2E-S04N02-CJ-B1 0.3M
E2E-S04N02-CJ-C2 0.3M
E2E-S04N02-CJ-B2 0.3M
Brown: +V
Black: Output
Blue: 0 V
E2E-S05N03-WC-C1 2M *1 *2
E2E-S05N03-WC-B1 2M *1 *2
E2E-S05N03-WC-C2 2M *1 *2
E2E-S05N03-WC-B2 2M *1 *2
1: +V,
3: 0 V,
4: Control output
E2E-S05N03-CJ-C1 0.3M
E2E-S05N03-CJ-B1 0.3M
E2E-S05N03-CJ-C2 0.3M
E2E-S05N03-CJ-B2 0.3M
E2E-S05N03-MC-C1
E2E-S05N03-MC-B1
E2E-S05N03-MC-C2
E2E-S05N03-MC-B2
*1. Models with 5-m cable length are also available with "5M" suffix. (Example: E2E-C04N03-WC-C1 5M)
*2. Models with robot (bending-resistant) cable are also available with "-R" in the model number. (Example: E2E-C04N03-WC-C1-R 2M)
4
E2E
Accessories (Sold separately)
Sensor I/O Connector (Socket on One Cable End)
A Sensor I/O Connector is not provided with the Sensor. It must be ordered separately as required.
[Refer to Dimensions on page 16.]
Cable
specifications
Size
Robot (bendingresistant) cable
M8
Number of cable
wires (conductors)
3
Straight
Cable length L (m)
Right-angle
Model
2
XS3F-M321-302-R
XS3F-M322-302-R
5
XS3F-M321-305-R
XS3F-M322-305-R
Mounting Brackets
A Mounting Bracket is not provided with the Sensor. It must be ordered separately as required.
[Refer to Dimensions on page 15.]
Applicable
Sensors
Model
Quantity
E2E-C03@
Y92E-SC03
1
Mounting block for 3 dia., M3-20 Hexagon socket head cap screws:
2pieces, M3 × P0.5 Hexagon nuts: 2pieces, Washers: 2pieces
E2E-C04@
Y92E-SC04
1
Mounting block for 4 dia., M3-20 Hexagon socket head cap screws:
2pieces, M3 × P0.5 Hexagon nuts: 2pieces, Washers: 2pieces
E2E-C05@
Y92E-SC05
1
Mounting block for 5.4 dia., M3-20 Hexagon socket head cap screws:
2 pieces, M3 × P0.5 Hexagon nuts: 2 pieces, Washers: 2 pieces
E2E-C06@
Y92E-SC06
1
Mounting block for 6.5 dia., M3-20 Hexagon socket head cap screws:
2pieces, M3 × P0.5 Hexagon nuts: 2pieces, Washers: 2pieces
E2E-S04@
Y92E-SS04
1
L-shaped Mounting Bracket for M4 screws
E2E-S05@
Y92E-SS05
1
L-shaped Mounting Bracket for M5 screws
Appearance
Remarks
Nut Set
A Nut Set is included with the Sensor. Order a Nut Set when required, e.g., if you lose the nuts.
Applicable Sensors
Model
Applicable sensor outer
diameter
E2E-S04@
Y92E-NWS04
M4
E2E-S05@
Y92E-NWS05
M5
Set contents
Clamping nuts: 2 pieces, toothed washer: 1 piece
Protective Stainless-steel Spiral Tube against Wire Breakage
A Spiral Tube is not provided with the Sensor. It must be ordered separately as required.
[Refer to Dimensions on page 16.]
Applicable Sensors
E2E-S04@
E2E-S05@
Model
Y92E-STS04-05
Y92E-STS04-10
Y92E-STS05-05
Y92E-STS05-10
Applicable sensor outer
diameter
M4
M5
Length
0.5 m
1m
0.5 m
1m
5
E2E
Ratings and Specifications
Size
Type
3 dia.
4 dia.
5.4 dia.
6.5 dia.
M4
M5
Shielded Unshielded Shielded Unshielded Shielded Shielded Unshielded Shielded Unshielded Shielded Unshielded
E2EE2EE2EE2EE2EE2EE2EE2EE2EE2EE2EItem
Model
C03SR8@ C03N02@ C04S12@ C04N03@ C05S01@ C06S02@ C06N04@ S04SR8@ S04N02@ S05S12@ S05N03@
2 mm
4 mm
0.8 mm
2 mm
1.2 mm
3 mm
Sensing distance
0.8 mm
2 mm
1.2 mm
3 mm
1mm
±10%
±10%
±10%
±10%
±10%
±10%
±10%
(at 23°C)
±10%
±10%
±10%
±10%
Setting distance *1
0 to 0.56
0 to 1.4
0 to 0.84
0 to 2.1
0 to 0.7
0 to 1.4
0 to 2.8
0 to 0.56
0 to 1.4
0 to 0.84
0 to 2.1
(Sensing distance × 0.7) mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
Differential travel
15% max. of sensing distance
Detectable object
Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 7.)
Standard sensing
Iron, 3 × 3
Iron, 6 × 6
Iron, 4 × 4
Iron, 9 × 9
Iron, 5.4 × 5.4 Iron, 6.5 × 6.5 Iron, 12 × 12 Iron, 3 × 3
Iron, 6 × 6
Iron, 4 × 4
Iron, 9 × 9
object
× 1 mm
× 1 mm
× 1 mm
× 1 mm
× 1 mm
× 1 mm
× 1 mm
× 1 mm
× 1 mm
× 1 mm
× 1 mm
Response frequency *2 5 kHz
3.5 kHz
4 kHz
2 kHz
4 kHz
3 kHz
3 kHz
5 kHz
3.5 kHz
4 kHz
2 kHz
Power supply voltage *3 10 to 30 VDC (including 10% ripple (p-p))
Current consumption 10 mA max.
200 mA max.
50 mA max.
100 mA max.
100 mA max.
Control Load current 50 mA max.
(60 to 70°C: 100 mA)
output
Residual
*4
2 V max. *5
voltage
Indicators
Operation indicator: Yellow (complies with European standard EN60947-5-2) Lights during output.
B1/B2: PNP open collector, C1/C2: NPN open collector
Operation mode
B1/C1 models: NO, B2/C2 models: NC
Protection circuits
Output reverse polarity protection, Power source circuit reverse polarity protection, Surge suppressor, Load short-circuit protection
Ambient
Operation and storage: −25 to 70°C (with no icing or condensation)
temperature range
Ambient
Operation and storage: 35% to 95% (with no condensation)
humidity range
Temperature
±15% max. of sensing distance at 23°C within temperature range of −25 to 70°C
influence
Voltage influence
±2.5% max. of sensing distance at rated voltage in the rated voltage ±15% range
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength
500 VAC, 50/60 Hz for 1 minute between current-carrying parts and case
Vibration resistance
Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance
Destruction: 500 m/s2 10 times each in X, Y, and Z directions
Degree of protection
IEC 60529 IP67, in-house standards: oil-resistant *6
Pre-wired
Yes
Yes
Yes
Yes
Yes
Yes
Models
ConM8 Pre-wired
necting Connector
Yes
Yes
No
Yes
Yes
Yes
method Models
M8 Connector
No
Yes
No
Yes
No
Yes
Models
Pre-wired
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
Models
25 g
30 g
35 g
35 g
35 g
55 g
55 g
30 g
30 g
35 g
40 g
Weight M8 Pre-wired
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
(packed Connector
--20 g
20 g
15 g
20 g
20 g
25 g
20 g
20 g
20 g
20 g
state)
Models
Approx.
Approx.
Approx.
Approx.
Approx.
Approx.
M8 Connector
----------15 g
15 g
10 g
15 g
10 g
10 g
Models
NickelCase
SUS303 (EN 1.4305) *7
plated
SUS303 (EN 1.4305) *7
brass
Sensing
Heat-resistant ABS
Materi- surface
als
Clamping
No
SUS430 (EN 1.4016) *7
nuts *8
Toothed
No
SUS303 (EN 1.4305) *7
washer *8
Cable
Polyvinyl chloride (PVC)
Instruction
Yes
manual
AccesModel label
Yes
sories
Mounting
Sold separately
brackets
*1. Using within the set distance enables high-speed responsiveness and a more stable repeat accuracy.
*2. The response frequency is an average value.
*3. When used at a power of 12 V, the Sensor is less susceptible to the effects of internal self heat generation and therefore a more stable repeat accuracy can be
obtained.
*4. When the control output is 20 mA or less, the Sensor is less susceptible to the effects of internal self heat generation and therefore a more stable repeat accuracy can be
obtained.
*5. 3 dia., M4: load current 50 mA, cable length 2 m
Oil resistance test
4 dia., 5.4 dia., M5: load current 100 mA, cable length 2 m
After the test time elapses, the characteristics
Test oil: Water insoluble oil
6.5 dia.: load current 200 mA, cord length 2 m
below are checked for problems.
Velocite No. 3
*6. Oil resistance in-house standard: Performance with respect
(1) Visual appearance (no damage that
(manufactured by
to water insoluble oil.
affects product characteristics)
Exxon Mobil)
(Test at right)
(2) Operation check (ON/OFF)
50°C × 250 hours
*7. Material name in EN standards.
(3) Insulation resistance (50 MΩ min. at
Depth 10 cm
*8. Clamping nuts: 2 pieces, toothed washer: 1 piece
500 VDC)
(4) Dielectric strength (500 VAC, 1 min.)
Sensor
(5) Water resistance (IP67)
6
E2E
Engineering Data (Reference Value)
Sensing Area
Unshielded Models
E2E-C/S@N@
Distance X (mm)
Distance X (mm)
Shielded Models
E2E-C/S@S@
2.5
E2E-C06S02@
2
E2E-C06N04@
4
3.5
3
E2E-C04S12@
E2E-S05S12@
1.5
4.5
2.5
E2E-C04N03@
E2E-S05N03@
2
1
E2E-C05S01@
Y
Y
E2E-C03SR8@
E2E-S04SR8@
X
0.5
E2E-C03N02@
E2E-S04N02@
1.5
1
X
0.5
0
-8
-6
-4
-2
0
2
0
-10
4
6
8
Distance Y (mm)
-5
0
5
10
Distance Y (mm)
Note: The workpiece is a standard sensing
object.
For details, refer to Ratings and
Specifications on page 6.
Influence of Sensing Object Size and Material
E2E-C04S12@/E2E-S05S12@
Iron
0.8
0.7
0.6
Stainless steel
(SUS304)
Brass
0.5
Iron
1.2
@d
X
1.0
t = 1 mm
0.8
@d
0.2
X
X
t = 1 mm
1.2
Iron
Stainless steel
(SUS304)
Brass
0.6
Aluminum
Copper
0.4
Brass
Aluminum
0.2
0.1
@d
1.4
0.8
Stainless steel
(SUS304)
0.4
t = 1 mm
1.6
1.0
0.6
Copper
0.3
0
1.4
Aluminum
0.4
E2E-C05S01@
1.6
Distance X (mm)
0.9
Distance X (mm)
Distance X (mm)
Shielded Models
E2E-C03SR8@/E2E-S04SR8@
0.2
Copper
5
10
15
20
25
30
0
35
5
10
Side length of sensing object: d (mm)
15
20
25
30
0
35
5
10
Side length of sensing object: d (mm)
15
20
25
30
35
Side length of sensing object: d (mm)
Distance X (mm)
E2E-C06S02@
2.5
Iron
2
@d
X
t = 1 mm
1.5
1
Stainless steel
(SUS304)
Brass
0.5
Aluminum
Copper
0
5
10
15
20
25
30
35
Side length of sensing object: d (mm)
Iron
2
Stainless steel
(SUS304)
1.5
E2E-C06N04@
3.5
Iron
3
Stainless steel
(SUS304)
2.5
1.5
1
@d
X
X
t = 1 mm
Iron
4
Stainless steel
(SUS304)
Aluminum
Copper
Copper
0.5
@d
Brass
Brass
Aluminum
5
3
2
1
Distance X (mm)
E2E-C04N03@/E2E-S05N03@
2.5
Distance X (mm)
Distance X (mm)
Unshielded Models
E2E-C03N02@/E2E-S04N02@
Brass
@d
t = 1 mm
2
X
t = 1 mm
Aluminum
1
Copper
0.5
0
5
10
15
20
25
30
35
Side length of sensing object: d (mm)
0
5
10
15
20
25
30
35
Side length of sensing object: d (mm)
0
5
10
15
20
25
30
35
Side length of sensing object: d (mm)
7
E2E
Distance - Horizontal Repeat Accuracy
E2E-C04S12@/E2E-S05S12@
12 VDC
0.7
24 VDC
0.6
E2E-C05S01@
1.2
12 VDC
24 VDC
1
0.8
0.5
0.4
1.2
Distance X (mm)
0.8
Distance X (mm)
Distance X (mm)
Shielded Models
E2E-C03SR8@/E2E-S04SR8@
1
24 VDC
0.8
0.6
@3 × 1 mm
0.3
X
0.6
@4 × 1 mm
ON point
repeat
accuracy
12 VDC
X
0.4
@5.4 × 1 mm
ON point
repeat
accuracy
X
0.4
ON point
repeat
accuracy
0.2
0.2
0.1
0
0.05
0.1
0.15
0.2
0
0.2
0.05
0.1
0.15
0.2
0
0.05
0.1
Repeat accuracy (mm)
Repeat accuracy (mm)
0.15
0.2
Repeat accuracy (mm)
Distance X (mm)
E2E-C06S02@
2
1.8
12 VDC
24 VDC
1.6
1.4
1.2
1
@6.5 × 1 mm
0.8
X
0.6
ON point
repeat
accuracy
0.4
0.2
0
0.05
0.1
0.15
0.2
Repeat accuracy (mm)
2
1.8
12 VDC
24 VDC
1.6
1.4
E2E-C06N04@
Distance X (mm)
E2E-C04N03@/E2E-S05N03@
Distance X (mm)
Distance X (mm)
Unshielded Models
E2E-C03N02@/E2E-S04N02@
3
12 VDC
24 VDC
2.5
4
12 VDC
24 VDC
3.5
3
2
2.5
1.2
1
1.5
@6 × 1 mm
0.8
X
0.6
2
@9 × 1 mm
ON point
repeat
accuracy
X
1
@12 × 1 mm
ON point
repeat
accuracy
1.5
X
ON point
repeat
accuracy
1
0.4
0.5
0.5
0.2
0
0.1
0.2
0.3
0.4
0.5
0
0.1
Repeat accuracy (mm)
0.2
0.3
0.4
0.5
0
0.1
Repeat accuracy (mm)
0.2
0.3
0.4
Sensing distance vs. repeat accuracy graphs
By using within the sensor installation distance, the repeat accuracy stabilizes.
This data is reference data based on a standard sensing object, and is not a guarantee of performance.
The repeat accuracy varies depending on the effects of temperature, the material and surface condition of the sensing object, and other conditions.
Minimum measurement gap
Model
E2E-C03S/S04S
0.3
0.6
E2E-C04S/S05S
0.4
E2E-C04N/S05N
0.9
E2E-C05S
0.3
E2E-C06S
0.6
E2E-C06N
1.2
Note: Measured at constant temperature of 23ºC using an iron sensing object of size
at least as large as standard sensing object (see right).
8
Size of test piece
Minimum gap (mm)
E2E-C03N/S04N
gap
30 mm
15 mm
30 mm
0.5
Repeat accuracy (mm)
Material: Iron
E2E
I/O Circuit Diagrams
Operation
mode
Output
specifications
Model
Timing chart
Non-sensing area
Output circuit
Sensing area
Proximity
Sensor
Sensing
object
Brown
100
(%)
E2E-@@@@
-@@-C1
NO
Rated
sensing
distance
Load
ON Operation
indicator
OFF (yellow)
ON Control
NPN opencollector
output
Proximity
Sensor
main
circuit
Blue
Non-sensing area
Sensing area
4
10 to 30 VDC
3
Proximity
Sensor
Sensing
object
Connector pin arrangement
100
(%)
NC
Black
OFF output
E2E-@@@@
-@@-C2
1
0
4
0
1
Rated
sensing
distance
3
M8
ON Operation
indicator
OFF (yellow)
ON Control
OFF output
Non-sensing area
Sensing area
Proximity
Sensor
Sensing
object
Brown
100
(%)
E2E-@@@@
-@@-B1
NO
Rated
sensing
distance
ON Operation
indicator
OFF (yellow)
ON Control
PNP opencollector
output
Sensing area
Black
10 to 30 VDC
Load
Blue
3
Connector pin arrangement
100
(%)
E2E-@@@@
-@@-B2
4
Proximity
Sensor
Sensing
object
NC
Proximity
Sensor
main
circuit
OFF output
Non-sensing area
1
0
4
0
1
Rated
sensing
distance
ON Operation
indicator
OFF (yellow)
3
M8
ON Control
OFF output
Connection to I/O Connector (Connector Models, Pre-wired Connector Models)
Sensor I/O Connector
NPN
1
1
Brown
4
4
Black
3
3
Blue
02: 2 m
05: 5 m
I/O connector cable,
connector arrangement diagram
XS3F-M32@-3@@-R
PNP
1
1
Brown
4
4
Black
3
3
Blue
1: Straight
2: Right-angle
4
3
1
9
E2E
Safety Precautions
Refer to Warranty and Limitations of Liability.
WARNING
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
CAUTION
• Do not short the load. Explosion or burning may
result.
• Do not supply power to the Sensor with no load,
otherwise Sensor may be damaged.
Precautions for Correct Use
Do not use this product under ambient conditions that exceed the
ratings.
● Design
Influence of Surrounding Metal
When mounting the Sensor within a metal panel, ensure that the
clearances given in the following table are maintained. Failure to
maintain these distances may cause deterioration in the performance
of the Sensor.
〈Shielded Models〉
〈Unshielded Models〉
l
l
n
m
d dia.
D
m
n
m
d dia.
C
D
m
l
l
(Unit: mm)
Size
3 dia.
4 dia.
5.4 dia.
6.5 dia.
M4
M5
L
0
0
0
0
0
0
m
3
5
3
6
3
5
d
3
4
5.4
6.5
4
D
0
0
0
0
n
8
10
8
12
c
0
0
0
2
Item
(Unit: mm)
Size
3 dia.
4 dia.
6.5 dia.
M4
M5
L
6
6
12
6
6
m
6
9
8
6
9
5
d
9
12
24
9
12
0
0
D
6
6
12
6
6
8
10
n
16
20
24
16
20
0
0
Item
If mounted in a surrounding non-magnetic metal such as aluminum or copper, the sensing distance may shorten by about 40 to 50%.
If used in a recessed installation, take into consideration the effects of the material on the sensing distance.
Mutual Interference
A
When installing Sensors face-to-face or side-by-side, ensure that the minimum distances given in the following table are maintained.
B
A
Mutual Interference
Size
Item
(Unit: mm)
3 dia.
4 dia.
5.4 dia.
M4
M5
Shielded
Unshielded
Shielded
Unshielded
Shielded
Shielded
Unshielded
Shielded
Unshielded
Shielded
Unshielded
A
20
80
20
80
20
20
80
20
80
20
80
B*
15
60
15
60
15
15
60
15
60
15
60
* Values when the connector size is not taken into consideration.
10
6.5 dia.
E2E
● Mounting
● High-speed responsiveness
Tightening Force
To obtain a better high-speed response, it is recommended that you
use the sensor at about 50% of the possible sensing distance.
A high-speed response may not be obtained with some sensing
object surfaces, materials, and shapes, or when the sensing distance
is greater than the set distance.
For the effects of materials, refer to Engineering Data on page 7.
〈Mounting threaded models (E2E-S@)〉
Do not tighten the nut with excessive force.
A washer must be used with the nut.
Tr
● Protective Stainless-steel Spiral Tube
The spiral tube is in a fixed state and is intended to provide protection
against wire breakage due to shock from tools or other objects.
Note: 1. Only use the provided nut and toothed washer.
Risk of changes in the sensing distance and damage if a different
material is used. If you lose the nut or washer, purchase an optional nut
set.
2. The following strengths assume washers are being used.
Size
Item
M4
Shielded
Tr
M5
Unshielded
Shielded
Unshielded
0.8 N·m
1 N·m
If you require repeated bending tolerance, use a sensor with a robot
(bending-resistant) cable or use a Connector Model together with a
connector cable that is specified for bending tolerance. (Example:
XS3F-M321-@@@-R)
Refer to Sensor I/O Connector on page 5.
● Block type mounting accessories
Note: Only use the provided nut.
〈Mounting unthreaded cylindrical models (E2E-C@)〉
Dimpled end of set screw (M3)
(Screw not provided)
L
● Repeated cable bending tolerance
Due to differences in dimensional tolerances, these cannot be used
with older small diameter proximity sensors. (E2E-CR6@, E2ECR8@, E2E-C1@)
● Bending radius for mounting
If the cable is bent from its base, the resin on the surface of the cable
may peel off, however, this will not affect the protective structure or
sensing performance.
Avoid bending the cable at less than 10 mm from the base.
When bending the cable, refer to the table below.
Size
3 dia.
4 dia.
5.4
dia.
6.5 dia.
Item
Shielded
Unshielded
Shielded
Unshielded
Shielded
Shielded Unshielded
L*
9 to 21
mm
15 to 27
mm
8 to 21
mm
14 to 27
mm
8 to 21
mm
12 to 26 mm
Cable diameter
Bending radius*
3 dia., M4
7 mm
4 dia., 5.4 dia., M5
9 mm
6.5 dia.
12 mm
10 mm
Sensor
R
* Excluding the operation indicator area.
* For a robot (bending-resistant) cable,
multiply the bending radius in the
above table by 1.7.
When using a set screw, tighten it to the torque indicated in the table above.
● Total Cable Length
● Oil resistance
If you extend the cable length, use a conductor cross section of 0.14
mm2 or greater and do not exceed a total length of 200 m for standard
cables or robot (bending-resistant) cables. It is assumed that an
independent metal conduit will be used.
Torque
0.2 N·m max.
0.4 N·m max.
In accordance with our oil resistance standard, we test oil resistance
based on water insoluble oil (complies with test oil based on JIS
C0920, Appendix 1).
When water soluble cutting oil is used, durability varies due to the
dilution ratio and other factors.
Please test oil resistance using the actual oil that will be used.
11
E2E
(Unit: mm)
Dimensions
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
Sensors
Pre-wired Models
(Shielded)
Mounting Hole Dimensions
Dimension
3 dia.
4 dia.
5.4 dia.
6.5 dia.
M4
M5
F (mm)
3.3 +0.5
0
4.2 +0.5
0
5.7 +0.5
0
7 +0.5
0
4.5 +0.5
0
5.5 +0.5
0
F
E2E-C04S12-WC-@@
E2E-C03SR8-WC-@@
2.4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.09 mm2,
Insulator diameter: 0.7 mm), Standard length: 2 m
27.1
0
3-0.1
dia.
18
E2E-C06S02-WC-@@
E2E-C05S01-WC-@@
25.1
*
Operation indicators (yellow) 4 × 90°
25.1
27.1
18
15.1
2.4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.09 mm2,
Insulator diameter: 0.7 mm), Standard length: 2 m
5
1
*
* Threaded section to secure
the Protective Stainless-steel
Spiral Tube (optional).
Mounting with clamping nuts
and a toothed washer is not
Operation indicators (yellow) 4 × 90°
M4 × P0.5
possible here.
Two clamping nuts Toothed washer
3
*
* 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section:
0.14 mm2, Insulator diameter: 0.85 mm), Standard length: 2 m
Model with robot (bending-resistant) cable: 4-dia. vinyl-insulated round cable
with 3 conductors (Conductor cross section: 0.3 mm2,
Insulator diameter: 1.2 mm), Standard length: 2 m
E2E-S05S12-WC-@@
E2E-S04SR8-WC-@@
0.6
24.1
Operation indicators (yellow) 4 × 90°
* 2.9-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section:
0.14 mm2, Insulator diameter: 0.8 mm), Standard length: 2 m
Model with robot (bending-resistant) cable: 2.9-dia. vinyl-insulated round cable
with 3 conductors (Conductor cross section: 0.15 mm2,
Insulator diameter: 1.05 mm), Standard length: 2 m
7
36
0
6.5-0.1
dia.
18.5
8.5 dia.
18.5
*
Operation indicators (yellow) 4 × 90°
* 2.9-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section:
0.14 mm2, Insulator diameter: 0.8 mm), Standard length: 2 m
Model with robot (bending-resistant) cable: 2.9-dia. vinyl-insulated round cable
with 3 conductors (Conductor cross section: 0.15 mm2,
Insulator diameter: 1.05 mm), Standard length: 2 m
Operation indicators (yellow) 4 × 90°
0
5.4-0.1
dia.
25.1
0
dia.
4-0.1
* 2.9-dia. vinyl-insulated round cable with 3
conductors (Conductor cross section: 0.14 mm2,
Insulator diameter: 0.8 mm), Standard length: 2 m
10 dia.
4
Model with robot (bending-resistant) cable: 2.9-dia.
0.6
vinyl-insulated round cable with 3 conductors
8
1
(Conductor cross section: 0.15 mm2,
3
*
Insulator diameter: 1.05 mm), Standard length: 2 m
*
* Threaded section to secure
the Protective Stainless-steel
M5 × P0.5
Operation indicators (yellow) 4 × 90° Spiral Tube (optional).
Mounting with clamping nuts
Two clamping nuts Toothed washer
and a toothed washer is not
possible here.
18.5
15.1
M8 Pre-wired Connector Models (0.3 m) (Shielded)
E2E-C03SR8-CJ-@@
E2E-C04S12-CJ-@@
2.4-dia. vinyl-insulated round cable,
Standard length: 300 mm
27.1
0
dia.
3-0.1
18
Operation indicators (yellow) 4 × 90°
2.9-dia. vinyl-insulated round cable,
Standard length: 300 mm
25.1
0
dia.
4-0.1
18.5
Operation indicators (yellow) 4 × 90°
M8 × P1
M8 × P1
E2E-S04SR8-CJ-@@
E2E-C06S02-CJ-@@
27.1
18
4-dia. vinyl-insulated round cable,
Standard length: 300 mm
36
0
dia.
6.5-0.1
24.1
8.5 dia.
15.1
0.6
7
3
Operation indicators (yellow) 4 × 90°
M8 × P1
M4 × P0.5
Two clamping nuts
E2E-S05S12-CJ-@@
25.1
18.5
10 dia.
15.1
4
0.6
8
3
M5 × P0.5
Two clamping nuts
12
*
2.9-dia. vinyl-insulated round cable,
1 Standard length: 300 mm
M8 × P1
Operation indicators (yellow) 4 × 90°
Toothed washer * Mounting with clamping nuts and a toothed
washer is not possible on this threaded section.
5
1
*
2.4-dia. vinyl-insulated round cable,
Standard length: 300 mm
M8 × P1
Operation indicators (yellow) 4 × 90°
Toothed washer
* Mounting with clamping nuts and a toothed
washer is not possible on this threaded section.
E2E
M8 Connector Models (Shielded)
E2E-C04S12-MC-@@
E2E-C06S02-MC-@@
40.1
0
dia.
4-0.1
43.5
4
24.2
18.5
0
6.5-0.1
dia.
28.5
24.1
6.75 dia.
Operation indicators (yellow) 4 × 90°
M8 × P1
Operation indicators (yellow) 4 × 90°
4
6.75 dia.
M8 × P1
E2E-S05S12-MC-@@
40.1
24.2
18.5
15.1
10 dia.
0.6
4
8
3
M5 × P0.5
6.75 dia. M8 × P1
Operation indicators (yellow) 4 × 90°
Two clamping nuts
Toothed washer
Pre-wired Models (Unshielded)
Mounting Hole Dimensions
Dimension
3 dia.
4 dia.
6.5 dia.
M4
M5
F (mm)
3.3 +0.5
0
4.2 +0.5
0
7 +0.5
0
4.5 +0.5
0
5.5 +0.5
0
F
E2E-C04N03-WC-@@
E2E-C03N02-WC-@@
33
0
3-0.1
dia.
6
2.4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.09 mm2,
Insulator diameter: 0.7 mm), Standard length: 2 m
23.9
31
0
dia.
4-0.1
*
Operation indicators (yellow) 4 × 90°
* 2.9-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section:
0.14 mm2, Insulator diameter: 0.8 mm), Standard length: 2 m
Model with robot (bending-resistant) cable: 2.9-dia. vinyl-insulated round cable
with 3 conductors (Conductor cross section: 0.15 mm2,
Insulator diameter: 1.05 mm), Standard length: 2 m
Operation indicators (yellow) 4 × 90°
E2E-S04N02-WC-@@
E2E-C06N04-WC-@@
35.9
0
6.5-0.1
dia. 6
24.4
6
33
24.2
8.5 dia.
7
Operation indicators (yellow) 4 × 90°
*
* 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section:
0.14 mm2, Insulator diameter: 0.85 mm), Standard length: 2 m
Model with robot (bending-resistant) cable: 4-dia. vinyl-insulated round cable
with 3 conductors (Conductor cross section: 0.3 mm2,
Insulator diameter: 1.2 mm), Standard length: 2 m
2.4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.09 mm2,
Insulator diameter: 0.7 mm), Standard length: 2 m
5
6.5
* Threaded section to secure
1
3
the Protective Stainless-steel
0
*
3-0.1 dia. 6
Spiral Tube (optional).
Mounting with clamping nuts
and a toothed washer is not
M4 × P0.5
Operation indicators (yellow) 4 × 90° possible here.
Two clamping nuts Toothed washer
23.9
21
E2E-S05N03-WC-@@
31
10 dia.
8
0
4-0.1 dia.
6.5
6
24.4
21
3
4
1
*2
*1
Operation indicators (yellow) 4 × 90°
Two clamping nuts Toothed washer
*1 2.9-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.14 mm2,
Insulator diameter: 0.8 mm), Standard length: 2 m
Model with robot (bending-resistant) cable: 2.9-dia. vinyl-insulated round cable with 3
conductors (Conductor cross section: 0.15 mm2,
Insulator diameter: 1.05 mm), Standard length: 2 m
*2 Threaded section to secure the Protective Stainless-steel Spiral Tube (optional).
Mounting with clamping nuts and a toothed washer is not possible here.
M5 × P0.5
13
E2E
M8 Pre-wired Connector Models (0.3 mm) (Unshielded)
E2E-C03N02-CJ-@@
E2E-C04N03-CJ-@@
2.4-dia. vinyl-insulated round cable,
Standard length: 300 mm
33
0
3-0.1
dia.
23.9
6
Operation indicators (yellow) 4 × 90°
2.9-dia. vinyl-insulated round cable,
Standard length: 300 mm
31
0
4-0.1
dia.
24.4
6
Operation indicators (yellow) 4 × 90°
M8 × P1
33
35.9
4-dia. vinyl-insulated round cable,
Standard length: 300 mm
24.2
6
0
dia.
6.5-0.1
M8 × P1
E2E-S04N02-CJ-@@
E2E-C06N04-CJ-@@
8.5 dia.
6.5
7
0
3-0.1 dia.
Operation indicators (yellow) 4 × 90°
M8 × P1
23.9
21
6
M4 × P0.5
Two clamping nuts
5
2.4-dia. vinyl-insulated round cable,
Standard length: 300 mm
1
3
M8 × P1
*
Operation indicators (yellow) 4 × 90°
Toothed washer * Mounting with clamping nuts and a
toothed washer is not possible on
this threaded section.
E2E-S05N03-CJ-@@
31
10 dia.
6.5
8
24.4
4
21
1
2.9-dia. vinyl-insulated round cable,
Standard length: 300 mm
3
6
0
4-0.1 dia.
*
M5 × P0.5
Operation indicators (yellow) 4 × 90°
M8 × P1
Toothed washer
* Mounting with clamping nuts and a
toothed washer is not possible on
this threaded section.
Two clamping nuts
M8 Connector Models (Unshielded)
E2E-C04N03-MC-@@
E2E-C06N04-MC-@@
43.4
46
4
0
-0.1
dia.
30.1
24.4
6
4
0
6.5 -0.1
dia.
28.4
24.2
4
6
6.75 dia.
Operation indicators (yellow) 4 × 90°
M8 × P1
E2E-S05N03-MC-@@
46
10 dia.
6.5
8
0
4 -0.1 dia.
4
3
6
M5 × P0.5
Two clamping nuts
14
30.1
24.4
21
M8 × P1
Operation indicators (yellow) 4 × 90°
Toothed washer
6.75 dia.
Operation indicators (yellow) 4 × 90°
M8 × P1
E2E
Accessories (Sold Separately)
Mounting Brackets
Y92E-SC04 (4-dia. block)
Y92E-SC03 (3-dia. block)
14.5
14.5
Material: Iron
25
5.5 dia.
3 dia.
1.5
Two hexagon
socket head
cap screws
M3×20
9
Material: Iron
1.5
Two hexagon
socket head
cap screws
M3×20
25
5.5 dia.
4 dia.
0.5
9.5
0.5
23
23
2.4
8 dia.
Two washers
Two hexagon
nuts M3×P0.5
8 dia.
12
5.5
12
5.5
Y92E-SC05 (5.4-dia. block)
Y92E-SC06 (6.5-dia. block)
14.5
Material: Iron
Two washers
Two hexagon
nuts M3×P0.5
2.4
14.5
Two hexagon
socket head
cap screws
M3×20
25
5.4 dia. 5.5 dia.
1.5
Material: Iron
0.5
10.2
Two hexagon
socket head
cap screws
M3×20
25
1.5
5.5 dia.
6.5 dia.
10.8
0.5
23
23
2.4
8 dia.
Two washers
Two hexagon
nuts M3×P0.5
Two washers
Two hexagon
nuts M3×P0.5
2.4
8 dia.
12
5.5
12
5.5
Y92E-SS05 (for M5 screw)
Y92E-SS04 (for M4 screw)
17
17
2-R1
A
2
A
5.1 +0.1
0 dia.
2
4 +0.1
dia.
0
Half punch
Half punch
20
14 ± 0.1
20
14±0.1
(R2)
1
Material: Iron
Material: Iron
5
1
5
A
R 0.3 max.
10
3.5
dia.
A
R 0.3 max.
2.5 ± 0.05 dia.
Cross sectional diagram A-A
± 0.1
R2
10 ± 0.1
2.5 ± 0.05 dia.
Cross sectional diagram A-A
3.5
dia.
22
8 ± 0.1
22
8 ± 0.1
2-R1
15
E2E
Protective Stainless-steel Spiral Tubes against Wire Breakage
Y92E-STS04-@
Y92E-STS05-@
L
L
8 dia.
A
4 dia.
A
8 dia.
A
A
7 dia.
7 dia.
Brass/nickel plating
Stainless steel (SUS304)
Brass/nickel plating
Brass/nickel plating
M4 × P0.5
Stainless steel (SUS304)
Brass/nickel plating
M5 × P0.5
5.6 dia.
5.6 dia.
12
12
2
16
2
16
12
12
L = 0.5 m (Y92E-STS05-05), 1 m (Y92E-STS05-10)
L = 0.5 m (Y92E-STS04-05), 1 m (Y92E-STS04-10)
Sensor I/O Connectors
XS3F-M32@-3@@-R
Straight
Soft PBT (UL94V-0)
L
4
3
1
50
4 dia.
9 dia.
M8×P1
Brass/nickel plating
21.5
31.4
5
30
L = 2 m (XS3F-M321-302-R),
5 m (XS3F-M321-305-R)
Right-angle
L
23.1
50
4 dia.
20.5
Soft PBT (UL94V-0)
30
5
9 dia.
Brass/nickel plating
1
4
3
16
4 dia.
M8×P1
L = 2 m (XS3F-M322-302-R),
5 m (XS3F-M322-305-R)
MEMO
17
MEMO
18
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have
any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing
by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE
PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL
SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products
or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election,
to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the
non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price
of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other
claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored,
installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or
unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in
writing, are not to be construed as an amendment or addition to the above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is
not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system,
or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with
respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it
to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice
to change part numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be
assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to
confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
OMRON Corporation
Industrial Automation Company
Authorized Distributor:
Tokyo, JAPAN
Contact: www.ia.omron.com
Regional Headquarters
OMRON EUROPE B.V.
Sensor Business Unit
Carl-Benz-Str. 4, D-71154 Nufringen, Germany
Tel: (49) 7032-811-0/Fax: (49) 7032-811-199
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
© OMRON Corporation 2013-2014 All Rights Reserved.
In the interest of product improvement,
specifications are subject to change without notice.
Printed in Japan
CSM_9_2_1015
Cat. No. D115-E1-03
0714 (0513)