Download

Digital Pressure Sensor
E8F2
CSM_E8F2_DS_E_4_3
Pressure Sensor with
Easy-to-Read LED Display
• Pressure status can be checked at a glance from the
digital display and bar display.
• Measurement pressure prevents incorrect outputs due
to momentary pressure changes. (*)
• Perform automatic teaching simply by teaching pressure
values for good and bad products.
• Industry’s smallest models at just 28 × 28 × 29 mm.
* Only in hysteresis mode.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Be sure to read Safety Precautions
on page 6.
Ordering Information
Sensors (Refer to Dimensions on page 7.)
Pressure range
Positive pressure
Negative pressure
0 to 100 kPa
0 to 1 MPa
0 to −101 kPa
ON/OFF output
Linear output
Open collector
(two independent outputs)
1 to 5 V
Model
NPN output
E8F2-A01C
E8F2-B10C
E8F2-AN0C
PNP output
E8F2-A01B
E8F2-B10B
E8F2-AN0B
Accessories (Order Separately) (Refer to Dimensions on page 7.)
Appearance
Name
Model
Remarks
Mounting Bracket E89-F3
Provided with the E8F2.
Panel-mounting
Bracket
Spacer provided.
E89-F4
1
E8F2
Ratings and Specifications
Sensor
Model
Item
NPN output
E8F2-A01C
E8F2-B10C
E8F2-AN0C
PNP output
E8F2-A01B
E8F2-B10B
E8F2-AN0B
Power supply voltage
12 to 24 VDC±10% with a ripple (p-p) of 10% max.
Current consumption
70 mA max. *1
Pressure type
Gauge pressure
Rated pressure range
0 to 100 kPa
0 to 1 MPa
0 to −101 kPa
Pressure setting range
0 to 100 kPa
0 to 1 MPa
0 to −101 kPa
Withstand pressure
400 kPa
1.5 MPa
400 kPa
Applicable fluid
Non-corrosive gas and non-flammable gas
Operating mode
Hysteresis mode, window mode, and automatic teaching mode
Repeat accuracy
(ON/OFF output)
±1%FS max.
Linearity (linear output)
±1%FS max.
Response time (ON/OFF output)
5 ms max.
Linear output
1 to 5 V ±5% F.S. with an output impedance of 1 kΩ and a permissible resistive load of 500 kΩ.
ON/OFF outputs
NO or NC open collector (depending on whether the output configuration is NPN or PNP)
Load current
30 mA max.
Output applied voltage
30 VDC max.
Residual voltage
NPN open collector output: 1 V max. with 30 mA load current
PNP open collector output: 2 V max. with 30 mA load current
Display *2
3.5-digit red LED
Green LED bar indicator
The orange LED is lit for two independent outputs with output transistor turned ON.
Green unit indicator
Display accuracy
±3%FS±1 digit max.
Protection circuits
Reverse polarity protection, load short-circuit protection
Ambient temperature range
Operating: 0 to 55°C
Storage: −10 to 60°C (with no icing)
Ambient humidity range
Operating/Storage: 35% to 85% (with no condensation)
Temperature influence
±3%FS max.
Voltage influence
±1.5%FS max.
Insulation resistance
100 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength
1,000 VAC at 1 min
Vibration resistance
Destruction: 10 to 500 Hz, 1.0-mm double amplitude or 150 m/s2, three times each for 11 min in the X, Y,
and Z directions
Shock resistance
Destruction: 300 m/s2 3 times each in the X, Y, and Z directions
Degree of protection
IP50 (IEC)
Pressure port
R (PT) 1/8 taper screw and M5 female screw
Connection method
Pre-wired (standard length: 2 m)
Cable
Approved by UL
Weight (packed state)
Material
Approx. 110 g
Pressure port
Case
Accessories
Aluminum die-cast
Heat-resistive ABS
Mounting Bracket, Instruction manual
*1. The current consumption is approximately 43 mA in energy-saving mode.
*2. Display Example of Digital Indicator
Model
E8F2-A01C
E8F2-B10C
E8F2-AN0C
Setting unit
kPa
Applied pressure
Digital display
100
1
0
0
0
1000
1
0
0
0
−101
−1
0
1
0
Note: The period ( ) in the display indicates the decimal point.
Its position will not change unless the setting unit is changed.
2
E8F2
Engineering Data (Reference Value)
Temperature vs. Linear Output Current Temperature vs. Operating Pressure Fluctuation
Fluctuation
E8F2-A01@
+10
Operating pressure fluctuation (%FS)
Linear output fluctuation (%FS)
E8F2-A01@
+5
Rated pressure
Pressure 0
0
−5
−10
−25
0
25
50 55
+10
+5
0
−5
−10
−25
75
0
25
Temperature (˚C)
Linearity
E8F2-A01@
E8F2-A01@
Linear Deviation (%FS)
Linear output voltage (V)
Pressure vs. Linear Output
6
5
4
3
50 55
75
Temperature (˚C)
+1
+0.5
0
2
−0.5
1
0
20
40
60
80
100
Pressure (kPa)
−1
0
25
50
75
100
Pressure (kPa)
3
E8F2
I/O Circuit Diagrams
NPN Output
Operating
mode
Timing chart
Model
Hysteresis mode
Pressure
Pressure
ON point
OFF point
OFF point
ON point
NO
OFF point −10% FS
max.
ON point −10% FS
max.
T
Output
OUT
indicator
(orange)
E8F2-A01C
E8F2-B10C
E8F2-AN0C
ON
T
Output
OFF
ON
OFF
Pressure
+12 to 24 V
OFF point
OFF point
ON point
T
ON
Pressure
Sensor
main
circuit
Gray
(linear)
OFF point −10% FS
max.
ON point −10% FS
max.
30 mA
max.
Load
Black
(ON/OFF1)
White (ON/OFF2)
1 to 5 V
Load
Blue
0V
T
Output
OFF
30 mA
max.
Load
Pressure
ON point
Output
Brown
OFF
OUT
ON
indicator
(orange) OFF
ON
NC
Output circuit
Window mode
ON
OFF
OUT
indicator ON
(orange) OFF
OUT
indicator ON
(orange) OFF
PNP Output
Operating
mode
Timing chart
Model
Hysteresis mode
Pressure
Pressure
ON point
OFF point
OFF point
ON point
NO
Output
E8F2-A01B
E8F2-B10B
E8F2-AN0B
ON
Output
OFF
ON
ON
ON point
OFF point
OFF point
ON point
ON
OUT
indicator ON
(orange) OFF
Black (ON/OFF1)
White (ON/OFF2)
Gray 1 to 5 V
30 mA
max.
(Linear)
Load
OFF point −10% FS
max.
ON point −10% FS
max.
Blue
Load
Load
30 mA
max.
0V
T
T
OFF
Pressure
sensor
main
circuit
Pressure
Pressure
Output
+12 to 24 V
Brown
OFF
OUT
ON
indicator
(orange) OFF
OFF
NC
OFF point −10% FS
max.
ON point −10% FS
max.
T
T
OUT
indicator
(orange)
Output circuit
Window mode
Output
ON
OFF
OUT
indicator ON
(orange) OFF
4
E8F2
Nomenclature
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Display Panel
Operation Keys
(1) Bar Indicator (Green)
Indicates the degree of measured pressure in relation to the set
pressure.
(2) Numeric and Menu Display (Red)
Indicates measurement values and setting menu items.
(3) Unit indicator (Green)
Indicates the unit used for detection. The unit indicated on the
indicator is the one currently set.
(4) OUT1 Indicator (Orange)
Lit when OUT1 is turned ON.
(5) OUT2 Indicator (Orange)
Lit when OUT2 is turned ON.
(6)
Up Key, (7)
Down Key
• Used to select or change the set items, set contents, and set values
in setting mode.
• Press either key to check the ON and OFF points in measurement
mode. The values are reset by pressing both keys simultaneously.
• Use together with the SET Key for setting the Sensor to a special
setting mode or energy-saving mode.
(8)
SET Key
• Used for entering the set contents and set values in setting mode.
• Used for setting the Sensor to basic setting mode or pressure
setting mode.
SET
5
E8F2
Safety Precautions
Refer to Warranty and Limitations of Liability.
WARNING
This product is not designed or rated for ensuring
safety of persons either directly or indirectly.
Do not use it for such purposes.
Precautions for Correct Use
Do not use this product in atmospheres or environments that exceed
product ratings.
● Installation
Do not use the Sensor in an environment subject to corrosive or
combustible gas.
● Wiring
If no linear output is used, cut the gray lead wire short and apply
insulating tape to the lead wire so that it will not come into contact with
any other terminal.
● Adjustments
• Filter the gas with an appropriate air filter so that the applied gas will
be free of moisture or oil.
• Be sure to use the Sensor under the rated pressure.
• When setting the set pressure of the ON or OFF point of the output
transistor by pressing the mode selection key, use a manometer if
precise pressure settings are required. The Sensor has a display
error of ±3% FS±1 digit at room temperature. Refer to Display
accuracy in Ratings and Specifications.
• Turning ON the power
The Sensor is ready to operate 0.5 s after it is turned ON. When the
load and Sensor are connected to separate power supplies, be
sure to turn ON the Sensor first.
● Others
Make sure the Sensor does not get wet.
● Mounting
• Do not apply a tensile strength in excess of 50 N to the cables or
connectors.
• The pressure port (made of aluminum die-cast) is fixed with tapered
R(PT) 1/8 male screws and M5 female screws. When using tapered
screws, use tapered Rc(PT) 1/8 female screws.
• Wrap the tapered R(PT) 1/8 male screws with sealing tape to
prevent any leakage. Tighten the male screws to a torque of 10 N·m
max.
• Tighten M5 female screws to a torque of 2 N·m max.
• Tighten each male screw by using a 12-mm wrench to hold its
hexagonal head, not its body.
E8F2
Hexagonal head
• When attaching the Mounting Bracket to the Sensor, make sure
that each M3 screw is tightened to a torque of 0.5 N·m max.
6
E8F2
Dimensions
(Unit: mm)
Sensors
E8F2
Display panel
28
1.5
2
27
(29)
25.5
(17)
9
8
Pressure port
Two, M3 depth 6
R(PT) 1/8
M5 depth 8
28
20
27
13.5
5
20.5
6
20
4-dia. vinyl-insulated round cable with 5 conductors
(Conductor cross-section: 0.15 mm2, Insulator diameter: 0.9 mm),
Standard length: 2 m
Mounting Hole Dimensions
With Mounting Bracket
Attached
Two, M3
20.5
29
27
15
20
5.4
20
42
28.5
15
Accessories (Order Separately)
Mounting Bracket
E89-F3
20.5
15±0.4
9
Two, 3.5 dia.
27
20
14.5
Four, R1
13.5
20
45˚
26.9
4.5
90˚±0. 5
Note: Provided with
the E8F2.
Two, 3.5 dia.
R7.25
R1.6 max.
1.6
Four, R2.5
7
E8F2
Panel-mounting Bracket
E89-F4
Panel Cutout Dimensions
20.65
12.15
Spacer Mounted
Spacer Not Mounted
36+0.5
0
33+0.5
0
36+0.5
0
+0.5
0
33
Panel*
4
Panel*
25
17
41.3
40
Note: Spacer provided.
40
20
11.5
Spacer
* Applicable panel thickness: 1.2 to 4 mm
Note: The spacer can be removed from the Panel-mounting Bracket.
The panel cutout dimensions can be adjusted as shown above by
attaching or detaching the spacer.
8
Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron
disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER
ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the
Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at
Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount
equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,
repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products
were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate
modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or
electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,
recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above
warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitation on Liability; Etc.
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.
Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself
is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,
system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product
with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence
thereof.
Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate
it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our
practice to change part numbers when published ratings or features are changed, or when significant construction changes are
made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers
may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at
any time to confirm actual specifications of purchased Product.
Errors and Omissions.
Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
2015.8
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2015 All Right Reserved.