24VL024H
2K I2C™ Serial EEPROM with Half-Array Write-Protect
Device Selection Table
Description:
Part Number
VCC Range
Max. Clock
24VL024H
1.5 to 3.6V
400 kHz(1)
Note 1: 100 kHz for VCC < 1.8V
Features:
• Single-Supply with Operation down to 1.5V
• Low-Power CMOS Technology:
- 400 μA active current, maximum
- 1 μA standby current, maximum
• 2-Wire Serial Interface Bus, I2C™ Compatible
• Schmitt Trigger Inputs for Noise Suppression
• Output Slope Control to eliminate Ground Bounce
• 100 kHz and 400 kHz Compatibility
• Page Write Buffer for up to 16 Bytes
• Self-Timed Write Cycle (including Auto-Erase)
• Hardware Write Protection for Half Array
(80h-FFh)
• Cascadable up to Eight Devices
• More than 1 Million Erase/Write Cycles
• ESD Protection > 4,000V
• Data Retention > 200 Years
• Factory Programming (QTP) Available
• 8-pin PDIP, SOIC, TSSOP, TDFN and MSOP
Packages
• Temperature Range:
The Microchip Technology Inc. 24VL024H is a 2 Kbit
Serial Electrically Erasable PROM with operation
down to 1.5V. The device is organized as a single block
of 256 x 8-bit memory with a 2-wire serial interface.
Low-current design permits operation with typical
standby and active currents of only 1 μA and 400 μA,
respectively. The device has a page write capability for
up to 16 bytes of data. Functional address lines allow
the connection of up to eight 24VL024H devices on the
same bus for up to 16 Kbits of contiguous EEPROM
memory. The device is available in the standard 8-pin
PDIP, 8-pin SOIC (150 mil), TSSOP, 2x3 TDFN and
MSOP packages.
Block Diagram
A0 A1 A2
I/O
Control
Logic
WP
HV Generator
Memory
Control
Logic
EEPROM
Array
XDEC
SDA SCL
Write-Protect
Circuitry
YDEC
VCC
VSS
Sense Amp.
R/W Control
- -20°C to +85°C
• Pb-Free and RoHS compliant
Package Types
SOIC, TSSOP
PDIP, MSOP
A0
1
8
VCC
A0
1
8
VCC
A1
2
7
WP
A1
2
7
WP
A2
3
6
SCL
A2
3
6
SCL
VSS
4
5
SDA VSS
4
5
SDA
TDFN
A0 1
A1 2
A2 3
VSS 4
© 2008 Microchip Technology Inc.
8 VCC
7 WP
6 SCL
5 SDA
DS22109A-page 1
24VL024H
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings (†)
VCC .............................................................................................................................................................................6.5V
All inputs and outputs w.r.t. VSS ......................................................................................................... -0.6V to VCC +1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied ..................................................................................................-20°C to +85°C
ESD protection on all pins ......................................................................................................................................................≥ 4 kV
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 1-1:
DC CHARACTERISTICS
DC CHARACTERISTICS
Param.
No.
Sym.
Characteristic
Electrical Characteristics:
VCC = +1.5V to 3.6V TA = -20°C to +85°C
Min.
Max.
Units
Conditions
—
—
—
D1
—
A0, A1, A2, SCL, SDA
and WP pins:
—
D2
VIH
High-level input voltage
0.7 VCC
—
V
—
D3
VIL
Low-level input voltage
—
0.3 VCC
V
—
D4
VHYS
Hysteresis of Schmitt
Trigger inputs
(SDA, SCL pins)
0.05 VCC
—
V
(Note)
D5
VOL
Low-level output voltage
—
0.40
V
IOL = 3.0 mA @ VCC = 3.6V
IOL = 2.1 mA @ VCC = 2.5V
D6
ILI
Input leakage current
—
±1
μA
VIN = VSS or VCC, WP = VSS
D7
ILO
Output leakage current
—
±1
μA
VOUT = VSS or VCC
D8
CIN,
COUT
Pin capacitance
(all inputs/outputs)
—
10
pF
VCC = 3.6V (Note)
TA = 25°C, f = 1 MHz
D9
ICC Read Operating current
—
400
μA
VCC = 3.6V, SCL = 400 kHz
—
3
mA
VCC = 3.6V
D10
ICCS
—
1
μA
VCC = 3.6V, SCL = SDA = VCC
WP = VSS, A0, A1, A2 = VSS
ICC Write
Note:
Standby current
This parameter is periodically sampled and not 100% tested.
DS22109A-page 2
© 2008 Microchip Technology Inc.
24VL024H
TABLE 1-2:
AC CHARACTERISTICS
Electrical Characteristics:
VCC = +1.5V to 3.6V TA = -20°C to +85°C
AC CHARACTERISTICS
Param.
Symbol
No.
Characteristic
Min.
Max.
Units
Conditions
1
FCLK
Clock frequency
—
—
100
400
kHz
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
2
THIGH
Clock high time
4000
600
—
—
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
3
TLOW
Clock low time
4700
1300
—
—
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
4
TR
SDA and SCL rise time
(Note 1)
—
—
1000
300
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
5
TF
SDA and SCL fall time
(Note 1)
—
—
1000
300
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
6
THD:STA
Start condition hold time
4000
600
—
—
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
7
TSU:STA
Start condition setup time
4700
600
—
—
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
8
THD:DAT
Data input hold time
0
—
ns
(Note 2)
9
TSU:DAT
Data input setup time
250
100
—
—
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
10
TSU:STO
Stop condition setup time
4000
600
—
—
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
11
TSU:WP
WP setup time
4000
600
—
—
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
12
THD:WP
WP hold time
4700
600
—
—
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
13
TAA
Output valid from clock
(Note 2)
—
—
3500
900
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
14
TBUF
Bus free time: Time the bus must
be free before a new transmission can start
1300
4700
—
—
ns
1.5V ≤ VCC < 1.8V
1.8V ≤ VCC ≤ 3.6V
15
TSP
Input filter spike suppression
(SDA and SCL pins)
—
50
ns
(Note 1 and Note 3)
ms
—
16
TWC
Write cycle time (byte or page)
—
5
17
—
Endurance
1M
—
cycles 25°C, VCC = 3.6V, Block mode
(Note 4)
Note 1: Not 100% tested. CB = total capacitance of one bus line in pF.
2: As a transmitter, the device must provide an internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
3: The combined TSP and VHYS specifications are due to new Schmitt Trigger inputs, which provide improved
noise spike suppression. This eliminates the need for a TI specification for standard operation.
4: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance™ Model which can be obtained from Microchip’s web site at
www.microchip.com.
© 2008 Microchip Technology Inc.
DS22109A-page 3
24VL024H
FIGURE 1-1:
BUS TIMING DATA
5
SCL
7
SDA
In
3
4
D4
2
8
10
9
6
15
14
13
SDA
Out
WP
DS22109A-page 4
(protected)
(unprotected)
11
12
© 2008 Microchip Technology Inc.
24VL024H
2.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
PIN FUNCTION TABLE
8-pin
PDIP
8-pin
SOIC
8-pin
TSSOP
8-pin
MSOP
8-pin
TDFN
A0
1
1
1
1
1
User Configurable Chip Select
A1
2
2
2
2
2
User Configurable Chip Select
A2
3
3
3
3
3
User Configurable Chip Select
VSS
4
4
4
4
4
Ground
Name
Function
SDA
5
5
5
5
5
Serial Data
SCL
6
6
6
6
6
Serial Clock
WP
7
7
7
7
7
Write-Protect Input
VCC
8
8
8
8
8
+1.5V to 3.6V
2.1
SDA Serial Data
2.4
WP
This is a bidirectional pin used to transfer addresses
and data into and out of the device. It is an open drain
terminal. Therefore, the SDA bus requires a pull-up
resistor to VCC (typical 10 kΩ for 100 kHz, 2 kΩ for
400 kHz).
WP is the hardware write-protect pin. It must be tied to
VCC or VSS. If tied to VCC, the hardware write protection
is enabled and will protect half of the array (80h-FFh).
If the WP pin is tied to VSS the hardware write
protection is disabled.
For normal data transfer, SDA is allowed to change
only during SCL low. Changes during SCL high are
reserved for indicating the Start and Stop conditions.
2.5
2.2
SCL Serial Clock
The SCL input is used to synchronize the data transfer
to and from the device.
2.3
Noise Protection
The 24VL024H employs a VCC threshold detector circuit that disables the internal erase/write logic if the
VCC is below 1.2 volts at nominal conditions.
The SCL and SDA inputs have Schmitt Trigger and
filter circuits that suppress noise spikes to assure
proper device operation, even on a noisy bus.
A0, A1, A2
The A0, A1 and A2 inputs are used by the 24VL024H
for multiple device operations. The levels on these
inputs are compared with the corresponding bits in the
slave address. The chip is selected if the compare is
true.
Up to eight 24VL024H devices may be connected to
the same bus by using different Chip Select bit
combinations. These inputs must be connected to
either VCC or VSS.
In most applications the chip address inputs, A0, A1
and A2, are hard-wired to logic ‘0’ or logic ‘1’. For
applications in which these pins are controlled by a
microcontroller or other programmable device, the chip
address pins must be driven to logic ‘0’ or logic ‘1’
before normal device operation can proceed.
© 2008 Microchip Technology Inc.
DS22109A-page 5
24VL024H
3.0
FUNCTIONAL DESCRIPTION
The 24VL024H supports a bidirectional, 2-wire bus and
data transmission protocol. A device that sends data
onto the bus is defined as a transmitter, and a device
receiving data as a receiver. The bus has to be controlled by a master device that generates the Serial
Clock (SCL), controls the bus access and generates
the Start and Stop conditions, while the 24VL024H
works as slave. Both master and slave can operate as
a transmitter or receiver, but the master device
determines which mode is activated.
DS22109A-page 6
© 2008 Microchip Technology Inc.
24VL024H
4.0
BUS CHARACTERISTICS
The data on the line must be changed during the low
period of the clock signal. There is one bit of data per
clock pulse.
The following bus protocol has been defined:
• Data transfer may be initiated only when the bus
is not busy.
• During data transfer, the data line must remain
stable whenever the clock line is high. Changes in
the data line while the clock line is high will be
interpreted as a Start or Stop condition.
Accordingly, the following bus conditions have been
defined (Figure 4-1).
Each data transfer is initiated with a Start condition and
terminated with a Stop condition. The number of the
data bytes transferred between the Start and Stop
conditions is determined by the master device and is,
theoretically, unlimited, though only the last sixteen will
be stored when doing a write operation. When an
overwrite does occur, it will replace data in a first-in
first-out fashion.
4.1
4.5
Bus Not Busy (A)
Each receiving device, when addressed, is required to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse which is associated with this Acknowledge bit.
Both data and clock lines remain high.
4.2
Start Data Transfer (B)
A high-to-low transition of the SDA line while the clock
(SCL) is high determines a Start condition. All
commands must be preceded by a Start condition.
4.3
Note:
A low-to-high transition of the SDA line while the clock
(SCL) is high determines a Stop condition. All
operations must be ended with a Stop condition.
Data Valid (D)
The state of the data line represents valid data when,
after a Start condition, the data line is stable for the
duration of the high period of the clock signal.
FIGURE 4-1:
SCL
(A)
The 24VL024H does not generate any
Acknowledge
bits
if
an
internal
programming cycle is in progress.
The device that acknowledges has to pull down the
SDA line during the Acknowledge clock pulse in such a
way that the SDA line is stable low during the high
period of the acknowledge-related clock pulse. Of
course, setup and hold times must be taken into
account. A master must signal an end of data to the
slave by not generating an Acknowledge bit on the last
byte that has been clocked out of the slave. In this case,
the slave must leave the data line high to enable the
master to generate the Stop condition (Figure 4-2).
Stop Data Transfer (C)
4.4
Acknowledge
DATA TRANSFER SEQUENCE ON THE SERIAL BUS CHARACTERISTICS
(B)
(C)
(D)
(C)
(A)
SDA
Start
Condition
FIGURE 4-2:
Address or
Acknowledge
Valid
Stop
Condition
Data
Allowed
to Change
ACKNOWLEDGE TIMING
Acknowledge
Bit
SCL
SDA
1
2
3
4
5
6
7
Data from transmitter
The transmitter must release the SDA line at this point
allowing the receiver to pull the SDA line low to acknowledge the previous eight bits of data.
© 2008 Microchip Technology Inc.
8
9
1
2
3
Data from transmitter
The receiver must release the SDA line at
this point so the transmitter can continue
sending data.
DS22109A-page 7
24VL024H
5.0
DEVICE ADDRESSING
A control byte is the first byte received following the
Start condition from the master device (Figure 5-1).
The control byte consists of a four-bit control code; for
the 24VL024H this is set as ‘1010’ binary for read and
write operations. The next three bits of the control byte
are the Chip Select bits (A2, A1, A0). The Chip Select
bits allow the use of up to eight 24VL024H devices on
the same bus and are used to select which device is
accessed. The Chip Select bits in the control byte must
correspond to the logic levels on the corresponding A2,
A1 and A0 pins for the device to respond. These bits
are in effect the three Most Significant bits of the word
address.
The last bit of the control byte defines the operation to
be performed. When set to a ‘1’, a read operation is
selected. When set to a ‘0’, a write operation is
selected. Following the Start condition, the 24VL024H
monitors the SDA bus, checking the control byte being
transmitted. Upon receiving a ‘1010’ code and appropriate Chip Select bits, the slave device outputs an
Acknowledge signal on the SDA line. Depending on the
state of the R/W bit, the 24VL024H will select a read or
write operation.
DS22109A-page 8
FIGURE 5-1:
CONTROL BYTE FORMAT
Read/Write Bit
Chip Select
Bits
Control Code
S
1
0
1
0
A2
A1
A0 R/W ACK
Slave Address
Start Bit
5.1
Acknowledge Bit
Contiguous Addressing Across
Multiple Devices
The Chip Select bits (A2, A1, A0) can be used to
expand the contiguous address space for up to 16K bits
by adding up to eight 24VL024H devices on the same
bus. In this case, software can use A0 of the control
byte as address bit A9, A1 as address bit A10, and A2
as address bit A11. It is not possible to sequentially
read across device boundaries.
© 2008 Microchip Technology Inc.
24VL024H
6.0
WRITE OPERATIONS
6.1
Byte Write
The higher order four bits of the word address remain
constant. If the master should transmit more than 16
bytes prior to generating the Stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the Stop condition is received, an
internal write cycle will begin (Figure 6-2). If an attempt
is made to write to the protected portion of the array
when the hardware write protection has been enabled,
the device will acknowledge the command, but no data
will be written. The write cycle time must be observed
even if write protection is enabled.
Following the Start signal from the master, the device
code (4 bits), the Chip Select bits (3 bits) and the R/W
bit (which is a logic low) are placed onto the bus by the
master transmitter. The device will acknowledge this
control byte during the ninth clock pulse. The next byte
transmitted by the master is the word address and will
be written into the Address Pointer of the 24VL024H.
After receiving another Acknowledge signal from the
24VL024H, the master device will transmit the data
word to be written into the addressed memory location.
The 24VL024H acknowledges again and the master
generates a Stop condition. This initiates the internal
write
cycle
and
the
24VL024H
will
not
generate Acknowledge signals during this time
(Figure 6-1). If an attempt is made to write to the
protected portion of the array when the hardware write
protection has been enabled, the device will
acknowledge the command, but no data will be written.
The write cycle time must be observed even if write
protection is enabled.
6.2
Note:
Page Write
The write-control byte, word address and the first data
byte are transmitted to the 24VL024H in the same way
as in a byte write. But instead of generating a Stop
condition, the master transmits up to 15 additional data
bytes to the 24VL024H that are temporarily stored in
the on-chip page buffer and will be written into the
memory once the master has transmitted a Stop
condition. Upon receipt of each word, the four lower
order Address Pointer bits are internally incremented
by one.
FIGURE 6-1:
6.3
Page write operations are limited to writing
bytes within a single physical page,
regardless of the number of bytes
actually being written. Physical page
boundaries start at addresses that are
integer multiples of the page buffer size (or
‘page size’) and end at addresses that are
integer multiples of [page size – 1]. If a
Page Write command attempts to write
across a physical page boundary, the
result is that the data wraps around to the
beginning of the current page (overwriting
data previously stored there), instead of
being written to the next page, as might be
expected. It is therefore necessary that the
application software prevent page write
operations that would attempt to cross a
page boundary.
Write Protection
The WP pin must be tied to VCC or VSS. If tied to VCC,
half of the array will be write-protected (80h-FFh). If the
WP pin is tied to VSS, write operations to all address
locations are allowed.
BYTE WRITE
Bus Activity
Master
S
T
A
R
T
SDA Line
S
Control
Byte
Word
Address
S
T
O
P
Data
P
A
C
K
Bus Activity
FIGURE 6-2:
A
C
K
A
C
K
PAGE WRITE
Bus Activity
Master
S
T
A
R
T
SDA Line
S
Control
Byte
Bus Activity
© 2008 Microchip Technology Inc.
Word
Address (n)
Data (n)
S
T
O
P
Data (n + 15)
Data (n +1)
P
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
DS22109A-page 9
24VL024H
7.0
ACKNOWLEDGE POLLING
Since the device will not acknowledge during a write
cycle, this can be used to determine when the cycle is
complete (this feature can be used to maximize bus
throughput). Once the Stop condition for a Write
command has been issued from the master, the device
initiates the internally-timed write cycle and ACK polling
can be initiated immediately. This involves the master
sending a Start condition followed by the control byte
for a Write command (R/W = 0). If the device is still
busy with the write cycle, no ACK will be returned. If no
ACK is returned, the Start bit and control byte must be
re-sent. If the cycle is complete, the device will return
the ACK and the master can then proceed with the next
Read or Write command. See Figure 7-1 for a flow
diagram of this operation.
FIGURE 7-1:
ACKNOWLEDGE POLLING
FLOW
Send
Write Command
Send Stop
Condition to
Initiate Write Cycle
Send Start
Send Control Byte
with R/W = 0
Did Device
Acknowledge
(ACK = 0)?
No
Yes
Next
Operation
DS22109A-page 10
© 2008 Microchip Technology Inc.
24VL024H
8.0
READ OPERATIONS
Read operations are initiated in the same way as write
operations, with the exception that the R/W bit of the
slave address is set to ‘1’. There are three basic types
of read operations: current address read, random read
and sequential read.
8.1
Current Address Read
The 24VL024H contains an address counter that maintains the address of the last word accessed, internally
incremented by one. Therefore, if the previous read
access was to address n, the next current address read
operation would access data from address n + 1. Upon
receipt of the slave address with the R/W bit set to ‘1’,
the 24VL024H issues an acknowledge and transmits
the 8-bit data word. The master will not acknowledge
the transfer, but does generate a Stop condition and the
24VL024H discontinues transmission (Figure 8-1).
8.2
Random Read
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, the word address must first
be set. This is done by sending the word address to the
24VL024H as part of a write operation.
FIGURE 8-1:
Once the word address is sent, the master generates a
Start condition following the acknowledge. This
terminates the write operation, but not before the
internal Address Pointer is set. The master then issues
the control byte again but with the R/W bit set to a ‘1’.
The 24VL024H will then issue an acknowledge and
transmits the eight-bit data word. The master will not
acknowledge the transfer, but does generate a Stop
condition and the 24VL024H discontinues transmission
(Figure 8-2). After this command, the internal address
counter will point to the address location following the
one that was just read.
8.3
Sequential Read
Sequential reads are initiated in the same way as a
random read except that after the 24VL024H transmits
the first data byte, the master issues an acknowledge
as opposed to a Stop condition in a random read. This
directs the 24VL024H to transmit the next sequentially
addressed 8-bit word (Figure 8-3).
To provide sequential reads, the 24VL024H contains
an internal Address Pointer which is incremented by
one at the completion of each operation. This Address
Pointer allows the entire memory contents to be serially
read during one operation. The internal Address
Pointer will automatically roll over from address FFh to
address 00h.
CURRENT ADDRESS READ
Bus Activity
Master
S
T
A
R
T
SDA Line
S
Bus Activity
© 2008 Microchip Technology Inc.
Control
Byte
S
T
O
P
Data
P
A
C
K
N
O
A
C
K
DS22109A-page 11
24VL024H
FIGURE 8-2:
Bus Activity
Master
SDA Line
RANDOM READ
S
T
A
R
T
Control
Byte
S
Bus Activity
Master
Control
Byte
S
T
O
P
Data (n)
P
S
A
C
K
A
C
K
Bus Activity
FIGURE 8-3:
S
T
A
R
T
Word
Address (n)
N
O
A
C
K
A
C
K
SEQUENTIAL READ
Control
Byte
Data (n)
Data (n + 1)
Data (n + 2)
S
T
O
P
Data (n + X)
P
SDA Line
Bus Activity
DS22109A-page 12
A
C
K
A
C
K
A
C
K
A
C
K
N
O
A
C
K
© 2008 Microchip Technology Inc.
24VL024H
9.0
PACKAGING INFORMATION
9.1
Package Marking Information
8-Lead PDIP (300 mil)
Example:
24VL024H
P e3112F
0821
XXXXXXXX
T/XXXNNN
YYWW
8-Lead SOIC (3.90 mm)
XXXXXXXT
XXXXYYWW
NNN
8-Lead TSSOP
Example:
24VL24H
SN e3 0821
12F
Example:
XXXX
V24H
TYWW
821
NNN
12F
8-Lead MSOP
XXXXXT
YWWNNN
8-Lead 2x3 TDFN
XXX
YWW
NN
© 2008 Microchip Technology Inc.
Example:
4V24H
82112F
Example:
AF3
821
12
DS22109A-page 13
24VL024H
Legend: XX...X
T
Y
YY
WW
NNN
e3
Note:
Part number or part number code
Temperature (I, E)
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code (2 characters for small packages)
Pb-free JEDEC designator for Matte Tin (Sn)
Note:
For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note:
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
Please visit www.microchip.com/Pbfree for the latest information on Pb-free conversion.
*Standard OTP marking consists of Microchip part number, year code, week code, and traceability code.
DS22109A-page 14
© 2008 Microchip Technology Inc.
24VL024H
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
N
NOTE 1
E1
1
3
2
D
E
A2
A
L
A1
c
e
eB
b1
b
6&!
'!
9'&!
7"')
%!
7,8.
7
7
7:
;
<
&
&
&
=
=
##44!!
-
1!&
&
=
=
"#&
"#>#&
.
-
-
##4>#&
.
<
: 9&
-<
-?
&
&
9
-
9#4!!
<
)
?
)
<
1
=
=
69#>#&
9
*9#>#&
: *+
1,
-
!"#$%&"' ()"&'"!&)
&#*&&&#
+%&,&!&
- '!
!#.#
&"#'
#%!
&"!
!
#%!
&"!
!!
&$#/!#
'!
#&
.0
1,21!'!
&$& "!
**&
"&&
!
* ,<1
© 2008 Microchip Technology Inc.
DS22109A-page 15
24VL024H
!
""#$%& !'
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
D
e
N
E
E1
NOTE 1
1
2
3
α
h
b
h
A2
A
c
φ
L
A1
L1
6&!
'!
9'&!
7"')
%!
β
99..
7
7
7:
;
<
&
: 8&
=
1,
=
##44!!
=
=
&#
%%+
=
: >#&
.
##4>#&
.
-1,
: 9&
1,
?1,
,'%@
&
A
=
3
&9&
9
=
3
&&
9
.3
3
&
I
B
=
<B
9#4!!
=
9#>#&
)
-
=
#%&
D
B
=
B
#%&1
&&
'
E
B
=
B
!"#$%&"' ()"&'"!&)
&#*&&&#
+%&,&!&
- '!
!#.#
&"#'
#%!
&"!
!
#%!
&"!
!!
&$#''!#
'!
#&
.0
1,2 1!'!
&$& "!
**&
"&&
!
.32 %'!
("!"*&
"&&
(%
%
'&
"
!!
* ,1
DS22109A-page 16
© 2008 Microchip Technology Inc.
24VL024H
!
""#$%& !'
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
© 2008 Microchip Technology Inc.
DS22109A-page 17
24VL024H
() )"* !
(+%+(
!
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
D
N
E
E1
NOTE 1
1
2
b
e
c
A
φ
A2
A1
L
L1
6&!
'!
9'&!
7"')
%!
99..
7
7
7:
;
<
&
: 8&
=
?1,
=
##44!!
<
&#
%%
=
: >#&
.
##4>#&
.
-
?1,
##49&
-
-
3
&9&
9
?
3
&&
9
.3
3
&
I
B
=
<B
9#4!!
=
9#>#&
)
=
-
!"#$%&"' ()"&'"!&)
&#*&&&#
'!
!#.#
&"#'
#%!
&"!
!
#%!
&"!
!!
&$#''!#
- '!
#&
.0
1,2 1!'!
&$& "!
**&
"&&
!
.32 %'!
("!"*&
"&&
(%
%
'&
"
!!
* ,<?1
DS22109A-page 18
© 2008 Microchip Technology Inc.
24VL024H
," !
*-, , !
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
D
N
E
E1
NOTE 1
1
2
e
b
A2
A
c
φ
L
L1
A1
6&!
'!
9'&!
7"')
%!
99..
7
7
7:
;
<
&
: 8&
=
?1,
=
##44!!
<
&#
%%
=
: >#&
.
##4>#&
.
-1,
: 9&
-1,
3
&9&
9
3
&&
9
1,
?
<
.3
3
&
B
=
<B
9#4!!
<
=
-
9#>#&
)
=
!"#$%&"' ()"&'"!&)
&#*&&&#
'!
!#.#
&"#'
#%!
&"!
!
#%!
&"!
!!
&$#''!#
- '!
#&
.0
1,2 1!'!
&$& "!
**&
"&&
!
.32 %'!
("!"*&
"&&
(%
%
'&
"
!!
* ,1
© 2008 Microchip Technology Inc.
DS22109A-page 19
24VL024H
.
$*-,/00%12(.
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
DS22109A-page 20
© 2008 Microchip Technology Inc.
24VL024H
.
$*-,/00%12(.
3
&'
!&"&4#*!(!!&
4%&
&#&
&&255***'
'54
© 2008 Microchip Technology Inc.
DS22109A-page 21
24VL024H
REVISION HISTORY
Revision A (10/2008)
Original release.
DS22109A-page 22
© 2008 Microchip Technology Inc.
24VL024H
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
•
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Development Systems Information Line
Customers
should
contact
their
distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the web site
at: http://support.microchip.com
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com, click on Customer Change
Notification and follow the registration instructions.
© 2008 Microchip Technology Inc.
DS22109A-page 23
24AA024H/24LC024H
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
To:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Device: 24VL024H
Y
N
Literature Number: DS22109A
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS22109A-page 24
© 2008 Microchip Technology Inc.
24VL024H
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
X
Temperature
Range
Device:
Package
24VL024H = 1.5V, 2 Kbit Addressable Serial EEPROM
24VL024HT = 1.5V, 2 Kbit Addressable Serial EEPROM
(Tape and Reel)
Temperature Range:
Package:
Note
/XX
P
SN
ST
MS
MNY(1)
1:
=
-20°C to +85°C
=
=
=
=
=
Plastic DIP, (300 mil Body), 8-lead
Plastic SOIC, (3.90 mm Body)
TSSOP, (4.4 mm Body), 8-lead
MSOP, (Plastic Micro Small Outline), 8-lead
TDFN, (2x3x0.75 mm Body), 8-lead
Examples:
a)
b)
c)
d)
24VL024H/P: 1.5V, PDIP Package.
24VL024H/SN: 1.5V, SOIC Package.
24VL024HT/ST: 1.5V, TSSOP Package,
Tape and Reel
24VL024HT/MNY: 1.5V, TDFN Package,
Tape and Reel
“Y” indicates a Nickel Palladium Gold (NiPdAu) finish.
© 2008 Microchip Technology Inc.
DS22109A-page 25
24VL024H
NOTES:
DS22109A-page 26
© 2008 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, rfPIC, SmartShunt and UNI/O are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
FilterLab, Linear Active Thermistor, MXDEV, MXLAB,
SEEVAL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, In-Circuit Serial
Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM,
PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo,
PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total
Endurance, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2008, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2008 Microchip Technology Inc.
DS22109A-page 27
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
01/02/08
DS22109A-page 28
© 2008 Microchip Technology Inc.