Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC-ABH241 v03.0412 Linear & Power Amplifiers - CHIP GaAs HEMT MMIC MEDIUM POWER Amplifier, 50 - 66 GHz Typical Applications Features This HMC-ABH241 is ideal for: Output IP3: +25 dBm • Short Haul / High Capacity Links P1dB: +17 dBm • Wireless LAN Bridges Gain: 24 dB • Military & Space Supply Voltage: +5V 50 Ohm Matched Input/Output Die Size: 3.2 x 1.42 x 0.1 mm Functional Diagram General Description The HMC-ABH241 is a four stage GaAs HEMT MMIC Medium Power Amplifier which operates between 50 and 66 GHz. The HMC-ABH241 provides 24 dB of gain, and an output power of +17 dBm at 1dB compression from a +5V supply voltage. All bond pads and the die backside are Ti/Au metallized and the amplifier device is fully passivated for reliable operation. The HMC-ABH241 GaAs HEMT MMIC Medium Power Amplifier is compatible with conventional die attach methods, as well as thermocompression and thermosonic wire bonding, making it ideal for MCM and hybrid microcircuit applications. All data shown herein is measured with the chip in a 50 Ohm environment and contacted with RF probes. Electrical Specifications, TA = +25° C, Vdd1= Vdd2= Vdd3= 5V, Idd1 + Idd2 + Idd3= 220mA [2] Parameter Min. Frequency Range Typ. Max. Units 50 - 66 GHz 24 dB Input Return Loss 15 dB Output Return Loss 15 dB Output Power for 1 dB Compression (P1dB) 17 dBm Output Third Order Intercept (IP3) 25 dBm Saturated Output Power (Psat) 19 dBm 220 mA Gain 19 Supply Current (Idd1 + Idd2 + Idd3) [1] Unless otherwise indicated, all measurements are from probed die [2] Adjust Vgg1 = Vgg2 = Vgg3 between -1V to +0.3V (typ -0.3V) to achieve Idd total = 220mA 1 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC-ABH241 v03.0412 GaAs HEMT MMIC MEDIUM POWER Amplifier, 50 - 66 GHz Fixtured Output Power vs. Frequency Linear Gain vs. Frequency 25 20 POUT (dBm) GAIN (dB) 20 15 10 15 P1dB P3dB 10 5 5 0 0 48 50 52 54 56 58 60 62 64 66 50 68 52 54 56 Input Return Loss vs. Frequency 60 62 64 66 68 Output Return Loss vs. Frequency 0 0 -5 -5 RETURN LOSS (dB) RETURN LOSS (dB) 58 FREQUENCY (GHz) FREQUENCY (GHz) -10 -15 -20 -25 -30 -10 -15 -20 -25 -30 -35 -35 48 50 52 54 56 58 60 FREQUENCY (GHz) 62 64 66 68 50 52 54 56 58 60 62 64 66 68 70 Linear & Power Amplifiers - CHIP 25 30 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 2 HMC-ABH241 v03.0412 GaAs HEMT MMIC MEDIUM POWER Amplifier, 50 - 66 GHz Linear & Power Amplifiers - CHIP Absolute Maximum Ratings Normal 5.0 V Supply to GND +5.5 Vdc Gate Bias Voltage -1 to +0.3 Vdc RF Input Power (Vdd = +5.0 V) 2 dBm Storage Temperature -65 °C to + 150°C Max Peak Reflow Temperature +180 °C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Reliability Information Junction Temperature to maintain 1 Million Hour MTTF +180 °C Normal Junction Temperature (T = +85 °C) +140.6 °C Thermal Resistance (Junction to Die Bottom) +50.6 °C/W Operating Temperature -55 °C to + 85°C Outline Drawing NOTES: Die Packaging Information [1] Standard Alternate GP-2 (Gel Pack) [2] [1] Refer to the “Packaging Information” section for die packaging dimensions. [2] For alternate packaging information contact Hittite Microwave Corporation. 3 1. ALL DIMENSIONS ARE IN INCHES [MM]. 2. TYPICAL BOND PAD IS .004” SQUARE. 3. BACKSIDE METALLIZATION: GOLD. 4. BACKSIDE METAL IS GROUND. 5. BOND PAD METALLIZATION: GOLD. 6. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS. 7. OVERALL DIE SIZE ±.002” 8. DIE THICKNESS = 0.004” For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC-ABH241 v03.0412 GaAs HEMT MMIC MEDIUM POWER Amplifier, 50 - 66 GHz Pad Descriptions Function Description 1 RFIN This pad is AC coupled and matched to 50 Ohms. 2, 4, 6, 10, 12, 14 Vgg1, Vgg2 Vgg3 Gate control for amplifier. Please follow “MMIC Amplifier Biasing Procedure” application note. See assembly for required external components. 3, 5, 7, 9, 11, 13 Vdd1, Vdd2, Vdd3 Power Supply Voltage for the amplifier. See assembly for required external components. 8 RFOUT This pad is AC coupled and matched to 50 Ohms. Die Bottom GND Die bottom must be connected to RF/DC ground. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] Linear & Power Amplifiers - CHIP Pad Number 4 HMC-ABH241 v03.0412 GaAs HEMT MMIC MEDIUM POWER Amplifier, 50 - 66 GHz Linear & Power Amplifiers - CHIP Assembly Diagram Note 1: Bypass caps should be 100 pF (approximately) ceramic (single-layer) placed no farther than 30 mils from the amplifier. Note 2: Best performance obtained from use of <10 mil (long) by 3 by 0.5 mil ribbons on input and output. 5 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC-ABH241 v03.0412 GaAs HEMT MMIC MEDIUM POWER Amplifier, 50 - 66 GHz Mounting & Bonding Techniques for Millimeterwave GaAs MMICs 50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film substrates are recommended for bringing RF to and from the chip (Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then attached to the ground plane (Figure 2). 0.102mm (0.004”) Thick GaAs MMIC Ribbon Bond 0.076mm (0.003”) RF Ground Plane Microstrip substrates should be placed as close to the die as possible in order to minimize bond wire length. Typical die-to-substrate spacing is 0.076mm to 0.152 mm (3 to 6 mils). Handling Precautions Follow these precautions to avoid permanent damage. Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment. Once the sealed ESD protective bag has been opened, all die should be stored in a dry nitrogen environment. Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean the chip using liquid cleaning systems. Static Sensitivity: strikes. 0.127mm (0.005”) Thick Alumina Thin Film Substrate Figure 1. 0.102mm (0.004”) Thick GaAs MMIC Ribbon Bond 0.076mm (0.003”) RF Ground Plane Follow ESD precautions to protect against ESD Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize inductive pickup. 0.150mm (0.005”) Thick Moly Tab 0.254mm (0.010” Thick Alumina Thin Film Substrate Figure 2. General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the chip may have fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers. Linear & Power Amplifiers - CHIP The die should be attached directly to the ground plane eutectically or with conductive epoxy (see HMC general Handling, Mounting, Bonding Note). Mounting The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The mounting surface should be clean and flat. Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for attachment. Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule. Wire Bonding RF bonds made with 0.003” x 0.0005” ribbon are recommended. These bonds should be thermosonically bonded with a force of 40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended. Ball bonds should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made with a nominal stage temperature of 150 °C. A minimum amount of ultrasonic energy should be applied to achieve reliable bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm). For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 6