TE Analog Devices Welcomes Hittite Microwave Corporation O B SO LE NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com TE O B SO LE THIS PAGE INTENTIONALLY LEFT BLANK HMC548LP3 / 548LP3E v03.1011 Features The HMC548LP3 / HMC548LP3E is ideal for: Single Supply: Vcc = +3 to +5V • Automotive Telematics Low Noise Figure: 1.3 dB • GPS Antenna Modules / Boosters High Output IP3: +21 dBm • Location Based Portables No External Matching Required • Satellite Navigation External Filter Access TE Typical Applications 3x3 mm Leadless SMT Package Functional Diagram General Description LE The HMC548LP3 & HMC548LP3E are comprised of two internally matched SiGe HBT MMIC low noise amplifier stages housed in 3x3 mm leadless SMT packages. The unique topology of the HMC548LP3 & HMC548LP3E provides interstage access allowing the designer to place a bandpass filter between the two amplifier stages. This filtering approach enables the receiver to reject nearby blocking signals such as those emitted from cellular and 3G hand-helds, without incurring the noise figure degradation associated with a high rejection pre-filter. When combined with the appropriate interstage bandpass filter, this LNA can be used as a receiver pre-amplifier in various applications from 1.2 to 3 GHz. Evaluation boards are available with or without a GPS L1 (1575 MHz) band pass filter. B SO Amplifiers - Low Noise - SMT SiGe HBT MMIC LOW NOISE AMPLIFIER, 1.2 - 3.0 GHz O Electrical Specifications, TA = +25°C* Parameter Min. Typ. Max. Frequency Range Vcc Gain Gain Variation Over Temperature Noise Figure Min. Typ. Max. 1575 MHz +3 20 23 Units 23 +5 V 26 dB 0.04 0.05 0.04 0.05 1.6 1.9 1.3 1.6 dB/°C dB Input Return Loss 8 8 Output Return Loss 14 16 dB Output 1 dB Compression (P1dB) 8 11 dBm Saturated Output Power (Psat) dB 10.5 12 dBm Output Third Order Intercept (IP3) 13 21 dBm Supply Current (Icc) 10 15 21 30 mA * All measurements include external 1.57 - 1.6 GHz (GPS L1) band pass filter connected between pin 4 & pin 9. 1 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC548LP3 / 548LP3E v03.1011 SiGe HBT MMIC LOW NOISE AMPLIFIER, 1.2 - 3.0 GHz Gain & Return Loss [1] Gain vs. Temperature [1] 25 28 15 10 GAIN (dB) S21 S11 S22 5 0 -10 -20 -25 1.55 1.56 1.57 1.58 12 1.56 1.59 FREQUENCY (GHz) +25C +85C -40C 1.565 1.57 1.575 1.58 1.585 1.59 -10 -15 -20 -25 1.56 1.59 O Reverse Isolation vs. Temperature [1] 1.565 1.58 1.585 1.59 1.585 1.59 5 +25 C +85 C -40 C 4 NOISE FIGURE (dB) -30 1.575 Noise Figure vs. Temperature [1] -10 -20 1.57 FREQUENCY (GHz) 0 REVERSE ISOLATION (dB) 1.585 +25C +85C -40C -5 FREQUENCY (GHz) +25C +85C -40C -40 -50 3 2 1 -60 -70 1.56 1.58 Output Return Loss vs. Temperature [1] B SO RETURN LOSS (dB) -10 1.56 1.575 0 -2 -8 1.57 LE 0 1.565 FREQUENCY (GHz) Input Return Loss vs. Temperature [1] -6 +25C +85C -40C 20 16 -15 -4 24 TE -5 RETURN LOSS (dB) RESPONSE (dB) 20 Amplifiers - Low Noise - SMT 32 30 1.565 1.57 1.575 1.58 FREQUENCY (GHz) 1.585 1.59 0 1.56 1.565 1.57 1.575 1.58 FREQUENCY (GHz) [1] Measurement includes external 1.57 - 1.6 GHz (GPS L1) band pass filter connected between pin 4 and pin 9. Vcc = +5V. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 2 HMC548LP3 / 548LP3E v03.1011 SiGe HBT MMIC LOW NOISE AMPLIFIER, 1.2 - 3.0 GHz 12 12 PSAT (dBm) 16 0 1.56 +25 C +85 C -40 C 1.565 1.57 1.575 1.58 1.585 0 1.56 1.59 1.58 1.585 1.59 Broadband Gain & Return Loss [2] 20 B SO 20 10 1.56 1.575 LE 22 12 1.57 40 24 14 1.565 FREQUENCY (GHz) Output IP3 vs. Temperature [1] 16 +25 C +85 C -40 C 4 FREQUENCY (GHz) 18 8 TE 8 RESPONSE (dB) P1dB (dBm) Psat vs. Temperature [1] 16 4 IP3 (dBm) Amplifiers - Low Noise - SMT P1dB vs. Temperature [1] -20 +25 C +85 C -40 C 1.565 1.57 1.575 1.58 1.585 0 -40 0.5 1.59 S21 S11 S22 1 1.5 2.5 3 3.5 4 Input Return Loss vs. Temperature [2] O Gain vs. Temperature [2] 2 FREQUENCY (GHz) FREQUENCY (GHz) 35 0 RETURN LOSS (dB) 30 GAIN (dB) 25 20 15 +25 C +85 C -40 C 10 -5 -10 -15 +25 C +85 C -40 C 5 0 0.5 1 1.5 2 2.5 FREQUENCY (GHz) 3 3.5 4 -20 0.5 1 1.5 2 2.5 3 3.5 4 FREQUENCY (GHz) [1] Measurement includes external 1.57 - 1.6 GHz (GPS L1) band pass filter connected between pin 4 and pin 9. Vcc = +5V. [2] Measurement includes external 50 Ohm line between pin 4 and pin 9. Vcc = +5V. 3 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC548LP3 / 548LP3E v03.1011 SiGe HBT MMIC LOW NOISE AMPLIFIER, 1.2 - 3.0 GHz Output Return Loss vs. Temperature [2] Reverse Isolation vs. Temperature [2] REVERSE ISOLATION (dB) -10 -20 +25 C +85 C -40 C -30 -10 +25 C +85 C -40 C -20 -30 -40 TE RETURN LOSS (dB) 0 -50 -60 -40 0.5 1 1.5 2 2.5 3 3.5 -70 0.5 4 1.5 2 2.5 3 3.5 4 3 3.5 4 3.5 4 LE Noise Figure vs. Temperature [2] P1dB vs. Temperature [2] 5 20 +25 C +85 C -40 C 2 1 0 1 1.5 2 2.5 3 3.5 P1dB (dBm) 3 15 B SO 4 NOISE FIGURE (dB) 1 FREQUENCY (GHz) FREQUENCY (GHz) 10 +25 C +85 C -40 C 5 0 0.5 4 1 1.5 FREQUENCY (GHz) 2.5 FREQUENCY (GHz) Output IP3 vs. Temperature [2] O Psat vs. Temperature [2] 2 Amplifiers - Low Noise - SMT 10 0 20 30 25 20 IP3 (dBm) PSAT (dBm) 15 10 0 0.5 1 1.5 2 2.5 3 +25 C +85 C -40 C 10 +25 C +85 C -40 C 5 15 5 3.5 4 FREQUENCY (GHz) 0 0.5 1 1.5 2 2.5 3 FREQUENCY (GHz) [2] Measurement includes external 50 Ohm line between pin 4 and pin 9. Vcc = +5V. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 4 HMC548LP3 / 548LP3E v03.1011 SiGe HBT MMIC LOW NOISE AMPLIFIER, 1.2 - 3.0 GHz Small Signal Parameters Input Stage [3] Small Signal Parameters Output Stage [3] 20 10 10 RESPONSE (dB) 0 -5 -10 -15 -25 S21 S11 S22 S12 -30 -35 -40 0.5 1 1.5 2 2.5 3 3.5 -40 0.5 4 1 1.5 2 2.5 3 3.5 4 3.5 4 LE 4 11 P1dB Input Stage P1dB Output Stage B SO -5 0.5 -20 Noise Figure Individual Stages [3] 15 -1 -10 FREQUENCY (GHz) P1dB Individual Stages [3] 3 0 -30 FREQUENCY (GHz) 7 S21 S11 S22 S12 TE -20 1 1.5 2 2.5 3.5 4 Input Stage Output Stage 3 2 1 0 0.5 1 1.5 2 2.5 3 FREQUENCY (GHz) O FREQUENCY (GHz) 3 NOISE FIGURE (dB) RESPONSE (dB) 5 P1dB (dBm) Amplifiers - Low Noise - SMT 15 [3] Vcc = +5V. 5 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC548LP3 / 548LP3E v03.1011 SiGe HBT MMIC LOW NOISE AMPLIFIER, 1.2 - 3.0 GHz Gain & Return Loss [4] Gain vs. Temperature [4] 25 26 15 5 GAIN (dB) S21 S11 S22 10 0 -10 -20 -25 1.55 1.56 1.57 1.58 10 1.56 1.59 FREQUENCY (GHz) 1.58 1.585 1.59 1.565 1.57 1.575 1.58 1.585 -10 -15 -20 1.56 1.59 O Reverse Isolation vs. Temperature [4] 1.565 1.575 1.58 1.585 1.59 1.585 1.59 Noise Figure vs. Temperature [4] 5 -10 +25C +85C -40C 4 NOISE FIGURE (dB) -30 1.57 FREQUENCY (GHz) 0 -20 +25C +85C -40C -5 FREQUENCY (GHz) REVERSE ISOLATION (dB) 1.575 Output Return Loss vs. Temperature [4] B SO RETURN LOSS (dB) +25C +85C -40C -4 +25C +85C -40C -40 -50 3 2 1 -60 -70 1.56 1.57 0 -2 -12 1.56 1.565 LE 0 -10 +25C +85C -40C FREQUENCY (GHz) Input Return Loss vs. Temperature [4] -8 18 14 -15 -6 22 TE -5 RETURN LOSS (dB) RESPONSE (dB) 20 Amplifiers - Low Noise - SMT 30 30 1.565 1.57 1.575 1.58 FREQUENCY (GHz) 1.585 1.59 0 1.56 1.565 1.57 1.575 1.58 FREQUENCY (GHz) [4] Measurement includes external 1.57 - 1.6 GHz (GPS L1) band pass filter connected between pin 4 and pin 9. Vcc = +3V. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 6 HMC548LP3 / 548LP3E v03.1011 SiGe HBT MMIC LOW NOISE AMPLIFIER, 1.2 - 3.0 GHz Psat vs. Temperature [4] 15 15 10 10 Psat (dBm) P1dB (dBm) 5 +25C +85C -40C 0 1.56 1.565 1.57 1.575 1.58 1.585 +25C +85C -40C TE 5 0 1.56 1.59 1.565 1.57 1.575 1.58 1.585 1.59 FREQUENCY (GHz) LE FREQUENCY (GHz) Output IP3 vs. Temperature [4] 20 IP3 (dBm) 15 B SO Amplifiers - Low Noise - SMT P1dB vs. Temperature [4] 10 5 0 1.56 1.565 1.57 1.575 +25C +85C -40C 1.58 1.585 1.59 FREQUENCY (GHz) O Absolute Maximum Ratings Typical Supply Current vs. Vcc +7.0 Vdc Vcc (Vdc) Icc (mA) RF Input Power (RFIN) -5 dBm 3.0 10 Junction Temperature 150 °C 4.5 17 5.0 21 5.5 24 Drain Bias Voltage (Vcc) Continuous Pdiss (T = 85 °C) (derate 14 mW/°C above 85 °C) 0.942 W Thermal Resistance (junction to ground paddle) 69 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1B ������������������������������ ���������������������������� [4] Measurement includes external 1.57 - 1.6 GHz (GPS L1) band pass filter connected between pin 4 and pin 9. Vcc = +3V. 7 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC548LP3 / 548LP3E v03.1011 SiGe HBT MMIC LOW NOISE AMPLIFIER, 1.2 - 3.0 GHz 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] LE 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC548LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] B SO HMC548LP3 Package Marking [3] 548 XXXX 548 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX Amplifiers - Low Noise - SMT NOTES: TE Outline Drawing Pin Descriptions Function Description 1 RFIN1 This pin is DC coupled and matched to 50 Ohms from 1.2 to 2.0 GHz. An off chip blocking capacitor is required. O Pin Number 2, 3, 5 - 8,10, 11, 13, 14, 16 GND These pins and package ground paddle must be connected to RF/DC ground. 4 RFOUT1 This pin is AC coupled and matched to 50 Ohms from 1.2 - 2 GHz. 9 RFIN2 This pin is DC coupled and matched to 50 Ohms from 1.2 to 2.0 GHz. An off chip blocking capacitor is required. 12 RFOUT2 This pin is AC coupled and matched to 50 Ohms from 1.2 - 2 GHz. 15 Vcc Power supply voltage for the amplifier. External bypass capacitors of 1,000pF and 18,000 pF are required. Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 8 HMC548LP3 / 548LP3E v03.1011 SiGe HBT MMIC LOW NOISE AMPLIFIER, 1.2 - 3.0 GHz Value C1, C2 150 pF C3 1,000 pF C4 18,000 pF TE Component B SO LE 1575 MHz Evaluation PCB O Amplifiers - Low Noise - SMT Application Circuit List of Material for Evaluation PCB 114254 [1] Item Description J1, J2 PCB Mount SMA Connector J3, J4 DC Pin C1, C2 150 pF Capacitor, 0402 Pkg. C3 1000 pF Capacitor, 0402 Pkg. C4 18,000 pF Capacitor, 0402 Pkg. U1 HMC548LP3 / HMC548LP3E Amplifier U2 Filter, Amotech AMOBP1575P02-A1 2.5 dB loss @ 1575 MHz PCB [2] 110980 Evaluation PCB The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed ground paddle should be connected directly to the ground plane similar to that shown above. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 9 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC548LP3 / 548LP3E v03.1011 SiGe HBT MMIC LOW NOISE AMPLIFIER, 1.2 - 3.0 GHz Amplifiers - Low Noise - SMT B SO LE TE Wideband (No Filter) Evaluation PCB O List of Material for Evaluation PCB 113979 [1] Item Description J1, J2 PCB Mount SMA Connector J3, J4 DC Pin C1, C2 150 pF Capacitor, 0402 Pkg. C3 1000 pF Capacitor, 0402 Pkg. C4 18,000 pF Capacitor, 0402 Pkg. U1 HMC548LP3 / HMC548LP3E Amplifier PCB [2] 113977 Evaluation PCB The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed ground paddle should be connected directly to the ground plane similar to that shown above. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10