Surge Protection Australia & New Zealand Core Assortment 2012-2013 For instrumentation, control and automation circuits www.weidmuller.com.au Surge protection for instrumentation, control and automation circuits VARITECTOR SPC VARITECTOR SSC Pluggable surge protection With a width of 6 mm in a compact terminal format For error detection and error messages as well as for monitoring instrumentation, control and automation circuits, Weidmüller developed the VARITECTOR SPC, its new families of surge protection devices. The VARITECTOR SPC, the pluggable surge protection, is characterised by highest protective functions with compact dimensions. With the VARITECTOR SPC R modules, error detection and error messages are realized by internal monitoring. Up to ten surge protection modules can be combined to transmit a message to the evaluation unit VARITECTOR SPC Control Unit. The advantage of all VARITECTOR SPC modules is that they are designed to be removed or exchanged during running operation - without interrupting the measuring circuit. The V-TEST unit is used for testing the function of the VARITECTOR SPC. It ensures that maintenance intervals can easily be adhered to, which is required by IEC 62305. For four binary signals or two analogue signals in just 17.8 mm of space are needed. The screw-free PE arrestor connection reliably enables the discharge of impulse currents up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) via a grounded mounting rail. 2 The VARITECTOR SSC family of surge protection devices for I&C circuits was developed with compact terminal-like dimensions (only 6.2 mm wide). The VARITECTOR SSC family comprises over 100 devices, thus being able to offer a fitting solution for any kind of surge protection. This protection comprises current loops and binary signals for 5 V, 12 V, 24 V, 48 V and 60 V. The terminals are equipped with complete integrated surge protection units or individual components such as varistors. Using a slotted-head Torx screw with a locking torque of 0.8 to 1.0 Nm, conductors ranging from 0.5 to 6 mm2 are connected providing proection against vibration . The safe discharge of surges up to 20 kA (8/20 μs) is realized by a snap-on connection to the mounting rail. A direct contact with the PE arrestor is established and excellent discharge properties are guaranteed for years. EMC Set For precise identification, all VARITECTOR products are equipped with large-scale marking capabilities: Connections for equipment or individual devices are labelled and the various voltage levels are marked by a colour code. Due to this, components can be quickly identified in a switching cabinet, thus simplifying both service and commissioning. All VARITECTOR SPC and SSC products were tested in accordance with the latest standards (IEC 61643-21): In classes D1, C1 and C2, they fulfil the safe short-circuit mode when units fail to overload of required. The EMC set offers additional convenience for connections with shielded cables. The EMC set consists of the EMC connector, i.e. the shield connector, and cable ties with shield cover EMC tie. The conductor shield can easily be connected to the clamping yoke connections of the VARITECTOR SPC modules. Contents For instrumentation, control and automation circuits 10 10 18 20 24 24 28 30 34 34 36 38 38 39 39 39 Analogue / Current Loop Protection VARITECTOR SPC VARITECTOR SSC 4AN VARITECTOR SSC 6AN Binary Digital Signal Protection VARITECTOR SPC VARITECTOR SSC 4AN VARITECTOR SSC 6AN Other Communication Types VARITECTOR SPC VARITECTOR SSC 6AN Accessories VSPC CONTROL UNIT 24 V DC VSPC V-TEST MARKING SOLUTIONS EMC SET 3 VARITECTOR SPC On 17.8 mm - four binary or two analogue signals with error messages and remote signaling Convenient and Safe Misconnection of the modules is prevented by a coding element Large Variety A solution for every type of surge protection: current loops and binary signals as well as integrated components and combinations of current loops and voltage supply e.g. 24 V. Quick Identification Colour-coded marking: simple identification of the different voltage levels in the switching cabinet. ≤ 12 V = green 24 V = binary signal, blue 24 V = analogue signal, yellow 48 V = red 60 V = violet Tester The pluggable arrestor VSPC can be tested with the V-TEST test instrument to comply with maintenance intervals in accordance with IEC 62305. Also suitable for energy surge protection units PU I and PU II. Monitoring Function Status display and message function: the protective function can be evaluated externally. Standard-Conformant Usable in accordance with installations standard IEC 62305: safely discharges high impulse currents up to 20 kA (8/20 µs) and 2,5 kA (10/350 µ) to PE. Tested for classes D1, C2 and C1 to IEC 61643-21. 4 VARITECTOR SSC Large variety: the solution for all cases of surge protection equipment Quick Identification Large-scale marking options: marking of connections for equipment or individual devices and colour-coded markings of the various voltage levels for quick identification in the switching cabinet. Large Variety More than 100 varieties: current loops and binary signals for 5 V, 12 V, 24 V, 48 V and 60 V and integrated components such as varistors. EMC Set Comprises shield connector and cable ties with shield cover. Using the EMC set, the conductor shield can easily be connected to the clamping yoke connections of the VSSC or VSPC modules. Convenient Comprises a clamping range from 0.5 mm≈ to 6 mm≈ with a slotted-head Torx screw and a locking torque of 0.8 to 1.0 Nm. Easy and Safe Easy installation and high safety through direct PE connection when snapped onto the mounting rail; high discharge current of up to 20 kA. Space-Saving Only 6.2 mm of line-up clamping width for binary or analogue signals. 5 PROTECTION OF ANALOGUE SIGNALS Protection of analogue signals and current loops (CL) In practice, the most common signals are analogue signals, also called current-loop signals. In most cases, analogue signals are needed to verify limit values (e.g., maximum or minimum temperature). Mostly, these signals are used for long distances. Analogue Signals 11 12 9 10 7 8 Grounded Surge Protection 6 5 3 4 1 2 TS unprotected protected 3 The standard forms are: 4 – 20 mA 0 – 20 mA 0–10 V 4 In practice, for example two-wire, threewire and four-wire measurements without common reference potential are carried out. The more wires there are, the more precise the measurements get with the means of protection thus becoming more important as well. Analogue Signals 11 12 9 10 7 8 Floating-Ground Surge Protection 6 5 3 4 1 2 unprotected Practical examples include: - Level measurements - Signals of voltage transmitters - PT 100 measurements - Temperature measurements protected TS 2 n ≤ 10 VSPC CONTROL UNIT 2 VSPC VSPC VSPC VSPC VSPC VSPC VSPC VSPC VSPC VSPC 2 X2 X2 X X2 X X2 X X2 X X2 X X2 X X2 X X2 X X2 X X2 2 X Error detection and error messages for two current loops or four binary signals with V-Control unit, a diagnosis or messaging module. 6 X +- PROTECTION OF BINARY SIGNALS Protection of binary signals (SL – symmetrical loop) Binary Signals 11 12 9 10 7 8 Floating-Ground 5 6 3 4 1 Surge Protection 2 unprotected protected TS Binary signals refer to bivalent (binary) states of processes. They can be described as 1/0 or as on/off. These defined states are also called logical values. The standard forms are: 0 ... 10 V 5 V ... 60 V 24 V 2 Binary Signals 11 12 9 10 7 8 5 6 4 3 2 1 unprotected Grounded Surge Protection TS protected 1 Up to ten VSPC surge protection modules can be incorporated into one monitoring circuit. Using the V-Control unit, also line breaks or interruptions in the circuit can be signaled. For binary signals, there are two kinds of surge protection components available - those with a common reference potential and those without. Two-wire connections are usually made with a common reference potential. These signals are for example signals from binary sensors, actuators or indicators. Practical examples include: - Limit switches - Push buttons - Position sensors - Photoelectric detectors - Contactors - Solenoid valves - Signal lamps The surge protection for floatingground (FG) models of binary signals is used in all applications, in which potential shifts may occur. These are mainly signals received in the field and transported over long distances. With this model, a gas discharge tube is introduced in series between the PE and the surge protection. This gas discharge tube inhibits coupling via PE. The surge protection for grounded models of binary signals is used mainly in those fields, in which all signals are laid directly to one star point or to one potential. 7 SIMPLE AND PRECISE ISOLATION The integrated disconnect lever guarantees that the measurement / control circuit can be quickly & precisely switched off to test the signal path TESTING EASE All connections are easily tested utilising the integrated test socket (Torx®/slot headed scew) and test plug. IEC COMPLIANT All VARITECTOR products comply with the latest IEC 61643-21:2008 requirement and with categories D1, C1, C2 and C3 according to IEC 61643-22. SURGE PROTECTION FOR CONTROL & INSTRUMENTATION Including disconnect/measurement function Weidmüllers New VSSC range of surge diverters provide surge protection for control & instrumentation circuits coupled with a market leading range of features (test points, disconnection, indication and identification). The entire VSSC range has been designd and tested to meet the current IEC standards and provide up to 20KA protection. Weidmüllers VSSC range will enable you to protect your installation without sacrificing space, design & serviceability. www.weidmuller.com.au Selection Guide VARITECTOR SPC - Choice of device depending on the interface Interface Pluggable arrestor 0(4) … 20 mA 0(4) … 20 mA 0 … 10 V 0 … 10 V ASI VSPC 2CL 24Vdc 0,5A VSPC 1CL 24Vdc 0,5A VSPC 2CL 24Vdc 0,5A VSPC 1CL 24Vdc 0,5A PU III R 48Vdc PU III R 24Vdc VSPC 2CL 12Vdc 0,5A VSPC 1CL 24Vdc 0,5A VSPC GDT 2ch 90V20kA Order No. Arrestor 8924470000 8924480000 8924470000 8924480000 8860350000 8860360000 8924440000 8924480000 8924570000 VSPC 1CL 48Vac 0,5A VSPC 1CL 24Vac 0,5A 8924520000 8924500000 Page 11 Page 11 VSPC 2CL HF 12Vdc VSPC R485 2ch VSPC 2SL 5Vdc 0,5A VSPC 1CL 12Vdc 0,5A VSPC 2CL HF 12Vdc VSPC 2CL HF 5Vdc VSPC 2CL HF 12Vdc VSPC 2CL HF 12Vdc 8924460000 8924670000 8924210000 8924450000 8924460000 8924430000 8924460000 8924460000 Page 15 Page 35 Page 25 Page 11 Page 15 Page 15 Page 15 Page 15 VSPC 3/4WIRE 24VDC PU III R 24Vdc VSPC 2CL HF 12Vdc VSPC 2CL HF 12Vdc VSPC 2CL HF 5Vdc VSPC 2CL HF 12Vdc 8924550000 8860360000 8924460000 8924460000 8924430000 8924460000 Cat 4.4 Cat 4.4 Page 15 Page 15 Page 15 Page 15 VSPC 2CL HF 12Vdc VSPC R485 2ch VSPC 2CL HF 12Vdc VSPC 2CL HF 12Vdc VSPC 1CL 12Vdc 0,5A VSPC 2CL HF 5Vdc VSPC 2CL HF 5Vdc VSPC R485 2ch VSPC 2CL 24Vdc 0,5A VSPC GDT 2ch 90V20kA VSPC 2CL HF 5Vdc VSPC 2CL HF 12Vdc VSPC 2CL HF 12Vdc 8924460000 8924670000 8924460000 8924460000 8924450000 8924430000 8924430000 8924670000 8924470000 8924570000 8924430000 8924460000 8924460000 Page 15 Page 35 Page 15 Page 15 Page 11 Page 15 Page 15 Page 35 Page 13 Cat 4.4 Page 15 Page 15 Page 15 Genius I/O Bus Hart Cathodic corrosion prevention LON (Works) M-Bus (Remote readout of counter) MODBUS(-PLUS) MPI-Bus N2 Bus Procontic CS31 Procontic T200 Profibus DP (FMS) Process-Bus, Panel-Bus PT100 P-Bus PSM-EG-RS422… PSM-EG-RS485… RACKBUS RS 422A, V.11, X.27, RS 423A RS 449 RS 485 RS-232-C/V.24 SDLC SecuriLan-LON-Bus SINEC L1 SINEC L2 DP Profibus DP TTY, 0(4) - 20 mA U-BUS V.35 X.21/X.24 X.25/X.31 Reference No. Page 13 Page 11 Page 13 Page 11 Cat 4.4 Cat 4.4 Page 13 Page 11 Cat 4.4 Pluggable arrestor with operation message (R) VSPC 2CL 24Vdc 0,5A R VSPC 1CL 12Vdc 0,5A R VSPC 2CL 24Vdc 0,5A R VSPC 1CL 12Vdc 0,5A R PU III R 48Vdc PU III R 24Vdc VSPC 2CL 12Vdc 0,5A R VSPC 1CL 24Vac 0,5A R Order No. Arrestor 8951480000 8951540000 8951480000 8951540000 8860350000 8860360000 8951470000 8951560000 VSPC 1CL 24Vdc 0,5A R 8951550000 Page 11 Page 11 VSPC 2CL HF 12Vdc R 8951690000 Page 15 VSPC 2SL 5Vdc 0,5A R VSPC 1CL 12Vdc 0,5A R VSPC 2CL HF 12Vdc R VSPC 2CL HF 5Vdc R VSPC 2CL HF 12Vdc R VSPC 2CL HF 12Vdc R 8951610000 8951540000 8951690000 8951680000 8951690000 8951690000 Page 25 Page 11 Page 15 Page 15 Page 15 Page 15 PU III R 24Vdc VSPC 2CL HF 12Vdc R VSPC 2CL HF 12Vdc R VSPC 2CL HF 5Vdc R VSPC 2CL HF 12Vdc R 8860360000 8951690000 8951690000 8951680000 8951690000 Cat 4.4 Page 15 Page 15 Page 15 Page 15 VSPC 2CL HF 12Vdc R VSPC R485 2ch R VSPC 2CL HF 12Vdc R VSPC 2CL HF 12Vdc R VSPC 1CL 12Vdc 0,5A R VSPC 2CL HF 5Vdc R VSPC 2CL HF 5Vdc R VSPC R485 2ch R VSPC 2CL 24Vdc 0,5A R 8951690000 8951670000 8951690000 8951690000 8951540000 8951680000 8951680000 8951670000 8951480000 Page 15 Page 35 Page 15 Page 15 Page 11 Page 15 Page 15 Page 35 Page 13 VSPC 2CL HF 5Vdc R VSPC 2CL HF 12Vdc R VSPC 2CL HF 12Vdc R 8951680000 8951690000 8951690000 Page 15 Page 15 Page 15 Reference No. Page 13 Page 11 Page 13 Page 11 Cat 4.4 Cat 4.4 Page 13 Page 11 Cat 4.4 This tables contains recommendations for the choice of device. Our technical consultants will be glad to assist you with your individual requirements. VARITECTOR VSSC - Choice of device depending on the interface Interface VSSC4 0(4) … 20 mA 0 … 10 V Genius I/O Bus Hart LON (Works) M-Bus (Remote readout of counter) MODBUS(-PLUS) Procontic CS31 RS 485 SecuriLan-LON-Bus Profibus DP VSSC4 CL 24Vuc 0.5A VSSC4 CL 24Vuc 0.5A VSSC4 CL 12Vdc 0.5A VSSC4 CL 24Vuc 0.5A VSSC4 CL 48Vuc 0.5A VSSC4 CL 24Vuc 0.5A Order No. Arrestor 1063730000 1063730000 1063720000 1063730000 1063740000 1063730000 VSSC4 CL 12Vdc 0.5A VSSC4 CL 12Vdc 0.5A - 1063720000 1063720000 - Reference No. VSSC6 Page 19 Page 19 Page 19 Page 19 Page 19 Page 19 VSSC 6CL 24Vuc 0.5A VSSC 6CL 24Vuc 0.5A VSSC 6CL 12Vdc 0.5A VSSC 6CL 24Vuc 0.5A VSSC 6CL 48Vuc 0.5A VSSC 6CL 24 Vuc 0.5A Order No. Arrestor 1064170000 1064170000 1064150000 1064170000 1064190000 1064170000 Page 19 Page 19 - VSSC 6RS485 VSSC 6CL 12 Vdc 0.5A VSSC 6RS485 VSSC 6CL 12 Vdc 0.5A VSSC 6RS485 1064980000 1064150000 1064980000 1064150000 1064980000 Reference No. Page 21 Page 21 Page 21 Page 21 Page 21 Page 21 Page 36 Page 21 Page 36 Page 21 Page 36 This tables contains recommendations for the choice of device. Our technical consultants will be glad to assist you with your individual requirements. Colour Coding Voltage level ≤ 12 V 24 V Binary 24 V Analogue Colour Green Blue Yellow Voltage level 48 V ≥ 60 V Special function Colour Red Violet White 9 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SPC VSPC 1CL - Protection for one analogue signal Imax 10kA • Optional monitoring function with status indicator and alert function • Pluggable arrester (plug-in/disconnect interruption-free and impedance neutral) • Testable with V-TEST instrument • Version with non-earthed PE connection for avoiding potential differences • Usable in accordance with installations standard IEC 62305 • Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE • IEC EX/ATEX versions available Technical data GND 11 12 7 8 9 10 GND 3 4 TS 5 6 1 2 unprotected protected Complete module, direct earthing 11 GND 12 7 8 9 10 GND OK FAULT 3 X2 X1 4 TS 5 6 1 for all VSPC 1CL Dielectric strength with FG against PE Volume resistivity per path Overstressed fault mode Requirement category acc. to IEC 61643-21 Surge strength C1 Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp. (10/350 μs) wire-wire / wire-PE / GND-PE Type of connection Storage temperature Ambient temperature (operational) Rel. humidity Degree of protection > 500 V 2.2 Ω Mode 2 C1; C2; C3; D1 < 1 kA / 8/20 µs 5 kA / 8/20 µs 100 A / 10/1000 µs 1 kA 10/350 µs 2.5 kA / 2.5 kA / 2.5 kA 10 kA / 10 kA / 10 kA 2.5 kA / 2.5 kA / 2.5 kA Pluggable in VSPC BASE -40 °C…+80 °C -40 °C…+70 °C 5 %…96 % RH IP20 2 unprotected protected Complete module, direct earthing, with remote alert 11 GND 12 7 8 9 10 GND 3 4 TS 5 6 1 2 unprotected protected Complete module, indirect earthing 11 12 7 GND 8 9 10 GND OK FAULT 3 X2 X1 4 TS 5 6 1 2 unprotected protected Complete module, indirect earthing, with remote alert Dimensions of complete module (arrester + base element) Length x Width x Height mm Note Without telecomm. contact With telecomm. contact (R) 90 x 17.8 x 69 98 x 17.8 x 69 This is a graphical representation only. Base elements / base to arresters Ordering data for base Type Base element, direct earthing Base element, indirect earthing via spark gap (FG, floating ground) Base element, direct earthing with remote alert Base element, indirect earthing with remote alert EX Base element, indirect earthing via spark gap (FG, floating ground) Note: The basis elements are to be ordered separately VSPC Control unit must be used with remote alert models PG 38. 10 Qty. 1 1 1 1 1 Order No. 8924730000 8924290000 8951730000 8951740000 8951810000 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SPC VSPC 1CL – arrester / plug-in elements Ordering data Rated voltage (DC) Max. continuous voltage, Uc (DC) Alternating-current strength Rated current Surge strength Signaling contact Optical function indicator (VSPC R) Transmission test (-3dB) Impulse reset tested Residual voltage Up wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/μs, typ. input 8/20 μs, typ. Protection level on output side unsym., input 1 kV/μs, typ. input 8/20 μs, typ. Ordering data Without signaling contact/function indicatorType Order No. With signaling contact/function indicator Type Order No. EX Version Type Order No. Note Ordering data Rated voltage (DC) Max. continuous voltage, Uc (DC) Alternating-current strength Rated current Surge strength Signaling contact Optical function indicator (VSPC R) Transmission test (-3dB) Impulse reset tested Residual voltage Up wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/μs, typ. input 8/20 μs, typ. Protection level on output side unsym., input 1 kV/μs, typ. input 8/20 μs, typ. Ordering data Without signaling contact/function indicatorType Order No. With signaling contact/function indicator Type Order No. Note VSPC 1CL 12 V DC VSPC 1CL 24 V DC 12 V DC 15 V DC 24 V DC 28 V DC 450 mA / 350 mA (EX Version) 450 mA / 350 mA (EX Version) UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 730 KHz 20 ms acc. to IEC61643-21 < 650 V 25 V / 450 V / 650 V UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 730 KHz 30 ms acc. to IEC61643-21 < 650 V 45 V / 450 V / 650 V < 25 V < 25 V < 45 V < 45 V < 450 V < 650 V < 450 V < 650 V VSPC 1CL 12VDC 0.5A 8924450000 VSPC 1CL 12VDC 0.5A R 8951540000 VSPC 1CL 12VDC EX 8953590000 VSPC 1CL 24VDC 0.5A 8924480000 VSPC 1CL 24VDC 0.5A R 8951550000 VSPC 1CL 24VDC EX 8953600000 VSPC 1CL 24 V AC VSPC 1CL 48 V AC 24 V AC / 34 V DC 28 V AC / 39 V DC 48 V AC / 68 V DC 60 V AC / 85 V DC 450 mA 350 mA UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 730 KHz 30 ms acc. to IEC61643-21 < 650 V 60 V / 450 V / 650 V no green = OK; red = arrester faulty, replace 730 KHz 100 ms acc. to IEC61643-21 < 650 V 85 V / 450 V / 650 V < 60 V < 60 V < 85 V < 85 V < 450 V < 650 V < 450 V < 650 V VSPC 1CL 24VAC 0.5A 8924500000 VSPC 1CL 24VAC 0.5A R 8951560000 VSPC 1CL 48VAC 0.5A 8924520000 11 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SPC VSPC 2CL - Protection for two analogue signals Imax 10kA • Optional monitoring function with status indicator and alert function • Pluggable arrester (plug-in / disconnect interruption-free and impedance neutral) • Testable with V-TEST instrument • Space-saving design for two analog signals with signaling contact, without additional space requirements • Version with non-earthed PE connection for avoiding potential differences • Usable in accordance with installations standard IEC 62305 • Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE • IEC EX/ATEX versions available Technical data GND 11 12 7 8 9 3 10 GND 4 TS 5 6 1 2 unprotected protected Complete module, direct earthing 11 12 7 GND 8 9 10 GND OK FAULT 3 X2 X1 4 TS 5 6 1 for all VSPC 2CL Dielectric strength with FG against PE Volume resistivity per path Overstressed fault mode Requirement category acc. to IEC 61643-21 Surge strength C1 Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp. (10/350 μs) wire-wire / wire-PE / GND-PE Degree of protection Type of connection Storage temperature Ambient temperature (operational) Rel. humidity Degree of protection > 500 V 2.2 Ω Mode 2 C1; C2; C3; D1 < 1 kA / 8/20 µs 5 kA / 8/20 µs 100 A / 10/1000 µs 1 kA 10/350 µs 2.5 kA / 2.5 kA / 2.5 kA 10 kA / 2 x 10 kA / 10kA 2.5 kA / 2.5 kA / 2.5 kA IP20 Pluggable in VSPC BASE -40 °C…+80 °C -40 °C…+70 °C 5 %…96 % RH IP20 2 unprotected protected Complete module, direct earthing, with remote alert 11 GND 12 7 8 9 10 GND 3 4 TS 5 6 1 2 unprotected protected Complete module, indirect earthing 11 GND 12 7 8 9 10 GND OK FAULT 3 4 TS 5 6 1 unprotected X2 X1 2 protected Complete module, indirect earthing, with remote alert Dimensions of complete module (arrester + base element) Length x Width x Height mm Note Without telecomm. contact With telecomm. contact (R) 90 x 17.8 x 69 98 x 17.8 x 69 This is a graphical representation only. Base elements / base to arresters Ordering data for base Type Base element, direct earthing Base element, indirect earthing via spark gap (FG, floating ground) Base element, direct earthing with remote alert Base element, indirect earthing with remote alert EX Base element, indirect earthing via spark gap (FG, floating ground) Note: The basis elements are to be ordered separately VSPC Control unit must be used with remote alert models PG 38. 12 Qty. 1 1 1 1 1 Order No. 8924710000 8924270000 8951710000 8951720000 8951820000 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SPC VSPC 2CL – arrester / plug-in elements Ordering data Rated voltage (DC) Max. continuous voltage, Uc (DC) Alternating-current strength Rated current Surge strength Signaling contact Optical function indicator (VSPC R) Transmission test (-3dB) Impulse reset tested Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/μs, typ. input 8/20 μs, typ. Protection level on output side unsym., input 1 kV/μs, typ. input 8/20 μs, typ. Ordering data Without signaling contact/function indicatorType Order No. With signaling contact/function indicator Type Order No. EX Version Type Order No. Note Ordering data Rated voltage (DC) Max. continuous voltage, Uc (DC) Alternating-current strength Rated current Surge strength Signaling contact Optical function indicator (VSPC R) Transmission test (-3dB) Impulse reset tested Residual voltage Up wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/μs, typ. input 8/20 μs, typ. Protection level on output side unsym., input 1 kV/μs, typ. input 8/20 μs, typ. Ordering data Without signaling contact/function indicatorType Order No. With signaling contact/function indicator Type Order No. Note VSPC 2CL 12 V DC VSPC 2CL 24 V DC 12 V DC 15 V DC 24 V DC 28 V DC 450 mA 450 mA / 250 mA (EX Version) UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 2.4 MHz 20 ms acc. to IEC61643-21 < 800 V 25 V / 450 V / 800 V UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 2.2 MHz 30 ms acc. to IEC61643-21 < 800 V 45 V / 450 V / 800 V < 25 V < 25 V < 45 V < 45 V < 450 V < 800 V < 450 V < 800 V VSPC 2CL 12VDC 0.5A 8924440000 VSPC 2CL 12VDC 0.5A R 8951470000 VSPC 2CL 24VDC 0.5A 8924470000 VSPC 2CL 24VDC 0.5A R 8951480000 VSPC 2CL 24VDC EX 8953720000 VSPC 2CL 24 V AC VSPC 2CL 48 V AC 24 V AC / 34 V DC 28 V AC / 39 V DC 48 V AC / 68 V DC 60 V AC / 85 V DC 450 mA 350 mA UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 3 MHz 450 ms acc. to IEC61643-21 < 650 V 60 V / 450 V / 800 V no < 60 V < 60 V green = OK; red = arrester faulty, replace 3 MHz 500 ms acc. to IEC61643-21 < 650 V 85 V / 450 V / 650 V 500 ms < 85 V < 85 V < 450 V < 800 V < 450 V < 650 V VSPC 2CL 24VAC 0.5A 8924490000 VSPC 2CL 24VAC 0.5A R 1093400000 VSPC 2CL 48VAC 0.5A 8951490000 13 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SPC VSPC 2CL HF – for high transmission rates without signal delays Imax 10kA • Optional monitoring function with status indicator and alert function • Pluggable arrester (plug-in / disconnect interruption-freeand impedance neutral) • Testable with V-TEST instrument • Space-saving design with optional signaling contact, without additional space requirements • High transmission rates with low attenuation values • Usable in accordance with installations standard IEC 62305 • Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE Technical data GND 11 12 7 8 9 3 10 GND 4 TS 5 6 1 2 unprotected protected Complete module, direct earthing 11 12 7 GND 8 9 10 GND OK FAULT 3 X2 X1 4 TS 5 6 1 2 unprotected for all VSPC 2CL HF Dielectric strength with FG against PE Rated current Volume resistivity per path Overstressed fault mode Requirement category acc. to IEC 61643-21 Surge strength C1 Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp. (10/350 μs) wire-wire / wire-PE / GND-PE Degree of protection Type of connection Storage temperature Ambient temperature (operational) Rel. humidity Degree of protection > 500 V 450 mA 2.2 Ω Mode 2 C1; C2; C3; D1 < 1 kA / 8/20 µs 5 kA / 8/20 µs 100 A / 10/1000 µs 1 kA 10/350 µs 2.5 kA / 2.5 kA / 2.5 kA 10 kA / 2 x 10 kA / 10kA 2.5 kA / 2.5 kA / 2.5 kA IP20 Pluggable in VSPC BASE -40 °C…+80 °C -40 °C…+70 °C 5 %…96 % RH IP20 protected Complete module, direct earthing, with remote alert 11 GND 12 7 8 9 10 GND 3 4 TS 5 6 1 2 unprotected protected Complete module, indirect earthing 11 12 7 GND 8 9 10 GND OK FAULT 3 X2 X1 4 TS 5 6 1 2 unprotected protected Complete module, indirect earthing, with remote alert Dimensions of complete module (arrester + base element) Length x Width x Height mm Note Without telecomm. contact With telecomm. contact (R) 90 x 17.8 x 69 98 x 17.8 x 69 This is a graphical representation only. Base elements / base to arresters Ordering data for base Type Base element, direct earthing Base element, indirect earthing via spark gap (FG, floating ground) Base element, direct earthing with remote alert Base element, indirect earthing with remote alert Note: The basis elements are to be ordered separately VSPC Control unit must be used with remote alert models PG 38. 14 Qty. 1 1 1 1 Order No. 8924710000 8924270000 8951710000 8951720000 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SPC VSPC 2CL HF – arrester / plug-in elements Ordering data Rated voltage (DC) Max. continuous voltage, Uc (DC) Alternating-current strength Surge strength Signaling contact Optical function indicator (VSPC R) Transmission test (-3dB) Impulse reset tested Residual voltage Up wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/μs, typ. input 8/20 μs, typ. Protection level on output side unsym., input 1 kV/μs, typ. input 8/20 μs, typ. Ordering data Without signaling contact/function indicatorType Order No. With signaling contact/function indicator Type Order No. Note VSPC 2CL HF 5 V DC VSPC 2CL HF 12 V DC VSPC 2CL HF 24 V DC 5 V DC 6.4 V DC 12 V DC 15 V DC 24 V DC 28 V DC UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 1.5 MHz 20 ms acc. to IEC61643-21 < 800 V 12 V / 450 V / 800 V UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 1.5 MHz 20 ms acc. to IEC61643-21 < 800 V 25 V / 450 V / 800 V UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 1.5 MHz 40 ms acc. to IEC61643-21 < 800 V 45 V / 450 V / 800 V < 12 V < 12 V < 25 V < 25 V < 45 V < 45 V < 450 V < 800 V < 450 V < 800 V < 450 V < 800 V VSPC 2CL HF 5VDC 8924430000 VSPC 2CL HF 5VDC R 8951680000 VSPC 2CL HF 12VDC 8924460000 VSPC 2CL HF 12VDC R 8951690000 VSPC 2CL HF 24VDC 8924510000 VSPC 2CLHF 24VDC R 8951700000 15 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SPC VSPC 1CL PW – combinations of current loop signal and power circuit Imax 10kA • Optional monitoring function with status indicator • Pluggable arrester (plug-in / disconnect interruption-free and impedance neutral) • Usable in accordance with installations standard IEC 62305 • Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE • Suitable for 4 wire analogue • IEC EX/ATEX versions available Technical data GND 11 12 7 8 9 10 GND 3 4 TS 5 6 U FAULT U 24 V~ 1 2 protected unprotected Complete module, direct earthing 11 GND 12 7 8 9 10 GND 3 4 TS 5 6 U FAULT U 24 V~ 1 unprotected Complete module, indirect earthing This is a graphical representation only. Base elements / base to arresters 2 protected for all VSPC 1CL PW C&I protection data Rated voltage (DC) Max. continuous voltage, Uc (DC) Dielectric strength with FG against PE Rated current Volume resistivity per path Overstressed fault mode Requirement category acc. to IEC 61643-21 Optical function indicator Rated voltage (AC/DC) Surge strength C1 Surge strength C2 Surge strength C3 Surge strength D1 Transmission test (-3dB) Impulse reset tested Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp. (10/350 μs) wire-wire / wire-PE / GND-PE Residual voltage Up Residual voltage Up wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/μs, typ. Protection level on output side sym., input 8/20 μs, typ. Protection level on output side unsym., input 1 kV/μs, typ. Protection level on output side unsym., input 8/20 μs, typ. Protection of the device Rated voltage (DC) Max. continuous voltage, Uc (DC) Combined pulse Residual voltage Up Rated current General data Type of connection Storage temperature Requirement category acc. to IEC 61643-1 Ambient temperature (operational) Rel. humidity Degree of protection Dimensions of complete module (arrester + base element) Length x Width x Height mm Note 24 V AC / 34 V DC 27 V AC / 38 V DC > 500 V / >350 mA (EX Version) 450 mA 2.2 Ω Mode 2 C1; C2; C3; D1 green = OK; red = arrester faulty, replace 24 V AC / 33 V DC < 1 kA / 8/20 µs 5 kA / 8/20 µs 100 A / 10/1000 µs 2.5 kA 10/350 µs 730 KHz 10 ms acc. to IEC61643-21, IEC61643-1 2.5 kA / 2.5 kA / 2.5 kA 10 kA / 10 kA / 10 kA 2.5 kA / 2.5 kA / 2.5 kA 800 V 60 V / 450 V / 800 V < 60 V < 60 V < 450 V < 800 V 24 V AC / 34 V DC 27 V AC / 38 V DC 6 kV 900 V 10 A Pluggable in VSPC BASE -40 °C…+80 °C Class III -40 °C…+70 °C 5 %…96 % RH IP20 Without telecomm. contact With telecomm. contact (R) 90 x 17.8 x 69 98 x 17.8 x 69 Ordering data for base Type Base element, direct earthing Base element, indirect earthing via spark gap (FG, floating ground) EX Base element, indirect earthing via spark gap (FG, floating ground) Note: The basis elements are to be ordered separately VSPC Control unit must be used with remote alert models PG 38. 16 Qty. 1 1 1 Order No. 1070230000 1105700000 1070470000 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SPC VSPC 1CL PW – arrester / plug-in elements Ordering data Without signaling contact/function indicatorType Order No. EX Version Type Order No. Note VSPC 1CL PW 24 V VSPC 1CL PW 24V 0.5A 8951510000 VSPC 1CL PW 24V EX 8953610000 17 VARITECTOR SSC 4 CL and CL FG Imax 5kA Two-stage surge protection with screw connection for instrumentation, control and automation technology •Surge protection in terminal-block format •Modular width of just 6.2 mm •Space-saving design: 1 analogue signal •Torx slotted screw connection •Version with non-earthed PE connection for avoiding potential differences •Usable in accordance with installations standard IEC 62305 •Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE • IEC EX/ATEX versions available Technical data 1 2 General data Nominal current IN at 25 °C Rated discharge current IN (8 / 20 µs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8 / 20 µs) wire-wire / wire-PE / GND-PE Response time wire-wire / wire-PE / GND-PE Volume resistivity per path Discharge current Itotal Rated discharge current Iimp (10 / 350 µs) Surge strength Max. continuous voltage Overstressed fault mode Requirement category acc. to IEC 61643-21 Rel. humidity Degree of protection Ambient temperature (operational) Storage temperature Approvals Clampable conductor Connection Stripping length Tightening torque range Solid / stranded Flexible / flexible with ferrule 3 4 TS protected unprotected VSSC4 CL 3 1 2 4 TS protected unprotected 500 mA 2.5 kA / 2.5 kA / 5 kA / 5 kA / ≤ 1 ns / ≤ 100 ns / 1.8 Ω ± 10% 10 kA 1 kA 4 kV / 2 kA, 10 repetitions 1 A / 1 s, 5 repetitions Mode 2 C1; C2; C3; D1 5%…96% RH IP20 -40 °C…+70 °C -40 °C…+80 °C UL, CSA pending Torx screw (T15) / slot (0.8 x 4.0) 7 mm 0.5 … 0.8 Nm 0.5 … 6 mm² / 0.5 … 4 mm² 0.5 … 2.5 mm² Dimensions Length x Width x Height mm Note: end plate AP VSSC4: 1063120000 VSSC4 CL FG This is a graphical representation only. 76 x 6.2 x 58.5 Applications 1 Load current I [A] Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SSC 4AN 0.8 0.6 0.4 0.4 0.2 0 -40 0 15 42.5 Ambient temperature T [°C] 18 70 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SSC 4AN PRODUCT SELECTION VARITECTOR SSC 4 CL and CL FG Ordering data Rated voltage UN Max. continuous voltage UC Voltage GND-PE Capacitance Gas discharge tube Supressordiode UP Limiting frequency (-3 dB) at load resistance Protection level at IN wire-wire / wire-PE / GND-PE 1 kV / µs wire-wire / wire-PE / GND-PE Ordering data Type Order No. Note Ordering data Rated voltage UN Max. continuous voltage UC Voltage GND-PE Capacitance Gas discharge tube Supressordiode UP Limiting frequency (-3 dB) at load resistance Protection level at IN wire-wire / wire-PE / GND-PE 1 kV / µs wire-wire / wire-PE / GND-PE Ordering data Type Order No. EX Version Type Order No. Note VSSC4 CL 12 V DC 0.5 A VSSC4 CL FG 12 V DC 0.5 A VSSC4 CL 24 V UC 0.5 A 12 V DC 15 V DC 4 nF 90 V 16 V 250 kHz 12 V DC 15 V DC > 500 V 4 nF 90 V 16 V 250 kHz 24 V AC / 34 V DC 30 V AC / 42 V DC 650 pF 90 V 43V 1.5 MHz 35 V / 600 V / 30 V / 600 V / - 35 V / 1500 V / 30 V / 1500 V / - 90 V / 600 V / 70 V / 600 V / - VSSC4 CL 12VDC 0.5A 1063720000 VSSC4 CL FG 12VDC 0.5A 1063760000 VSSC4 CL 24VUC 0.5A 1063730000 VSSC4 CL FG 24 V UC 0.5 A VSSC4 CL 48 V UC 0.5 A VSSC4 CL FG 48 V UC 0.5 A 24 V AC / 34 V DC 30 V AC / 42 V DC > 500 V / 300 mA (EX Version) 650 pF 90 V 43V 1.5 MHz 48 V AC / 68 V DC 60 V AC / 85 V DC 450 pF 150 V 91 V 2.2 MHz 48 V AC / 68 V DC 60 V AC / 85 V DC > 500 V / 300 mA (EX Version) 450 pF 150 V 91 V 2.2 MHz 90 V / 1500 V / 70 V / 1500 V / - 200 V / 600 V / 150 V / 600 V / - 200 V / 1500 V / 150 V / 1500 V / - VSSC4 CL FG 24VUC 0.5A 1063770000 VSSC4 CL FG 24VUC EX 1063810000 VSSC4 CL 48VUC 0.5A 1063740000 VSSC4 CL FG 48VUC 0.5A 1063780000 VSSC4 CL FG 48VUC EX 1063820000 19 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SSC 6AN VSSC 6AN CL and TR CL – protection for analogue signals (CL) with disconnect lever (TR) Imax 5kA Two stage surge protection with screw connection for instrumentation, control and automation technology • Surge protection in terminal block format • Modular width of just 6.2 mm • Space saving design: 1 analogue signal • Torx® slotted screw connection • Can be used to comply with the IEC 62305 installation standard and the IEC 61643-1/-22 standards • Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE Similar to illustration Similar to illustration Similar to illustration Similar to illustration Technical data 1 4 2 5 3 6 TS UNPROTECTED PROTECTED VSSC 6 CL 1 4 2 5 3 6 TS UNPROTECTED General data Nominal current Dielectric strength at FG against PE Volume resistivity Overstressed fault mode Requirement category IEC 61643-21 Standards Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp (10/350 μs) wire-wire / wire-PE / GND-PE Storage temperature Ambient temperature (operational) Humidity Degree of protection Flammability class Connection data Connection Tightening torque Conductor cross section, flexible, ferrule (DIN 46228-1), max. Conductor cross section, flexible, ferrule (DIN 46228-1), min. Conductor cross section, solid, max. Conductor cross section, solid, min. Conductor cross section, stranded, Rated connection, max. Conductor cross section, stranded, Rated connection, min. Stripping length Mounting rail Dimensions Length x width x height 500 mA (see derating curve) – 1.8 Ω ± 10 % Mode 2 C2; C3; D1 IEC 61643-21 2.5 kA 50 A 0.5 kA 2.5 kA / 2.5 kA / – 5 kA / 5 kA / – – / 0.5 kA / – -40 °C...+80 °C -40 °C...+70 °C 5...96 % RH IP20 V0 Torx® T15 / slot 0.8 x 4 0.5 Nm 4 mm² 0.5 mm² 6 mm² 0.5 mm² 4 mm² 0.5 mm² 10 mm TS35 88.5 x 6.2 x 81 mm PROTECTED VSSC 6 TR CL Derating curve I/A 1 0.8 0.6 0.6 0.6 0.6 0.5 0.4 0.4 0.2 0 -40 ºC 0 ºC 15 ºC 42.5 ºC TU 70 ºC Accessories: Screwdriver: Torx® 9009170000, slotted 9008340000; test plug: PS 2.3 0180400000; EMC SET: 1067470000; marker: WS 10/6 1818400000, DEK 6 0468560000, SNAPMARK 1805880000; end plate: 1063110000 This is a graphical representation only. 20 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SSC 6AN PRODUCT SELECTION VSSC 6 CL and TR CL Technical data Rated voltage AC/DC Max. continuous voltage UC (AC) / (DC) Signal transmission properties (-3 dB) Pulse reset capacity Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/µs, typ. Protection level on output side unsym., input 1 kV/µs, typ. Ordering data Type Order No. Note Technical data Rated voltage AC/DC Max. continuous voltage UC (AC) / (DC) Signal transmission properties (-3 dB) Pulse reset capacity Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/µs, typ. Protection level on output side unsym., input 1 kV/µs, typ. Disconnect lever Testing option Ordering data Type Order No. Note CL 12 V DC CL 24 V UC CL 48 V UC 12 V DC 15 V DC ≤ 700 kHz ≤ 20 ms ≤ 1600 V 35 V / 900 V / - 24 V AC / 34 V DC 30 V AC / 42 V DC ≤ 700 kHz ≤ 170 ms ≤ 1650 V 90 V / 900 V / - 48 V AC / 68 V DC 200 V / 770 V / - 30 V 70 V 70 V 900 V 900 V 770 V VSSC6 CL 12Vdc 0.5A 1064150000 VSSC6 CL 24Vuc 0.5A 1064170000 VSSC6 CL 48Vuc 0.5A 1064190000 TR CL 12 V DC TR CL 24 V UC TR CL 48 V UC 12 V DC 15 V DC ≤ 700 kHz ≤ 20 ms ≤ 1600 V 35 V / 900 V / - 24 V AC/ 34 V DC 90 V / 900 V / - 48 V AC / 68 V DC 60 V AC / 85 V DC ≤ 700 kHz ≤ 150 ms ≤ 1510 V 200 V / 770 V / - 30 V 70 V 150 V 900 V 900 V 770 V Yes Functional screw with test plug receptacle connection 1, 2, 4, 5 Yes Functional screw with test plug receptacle connection 1, 2, 4, 5 Yes Functional screw with test plug receptacle connection 1, 2, 4, 5 VSSC6 TR CL 12Vdc 0.5A 1064220000 VSSC6 TR CL 24Vuc 0.5A 1064230000 VSSC6 TR CL 48Vuc 0.5A 1064240000 30 V AC/ 42 V DC ≤ 700 kHz ≤ 170 ms ≤ 1650 V 60 V AC / 85 V DC ≤ 700 kHz ≤ 150 ms ≤ 1510 V 21 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SSC 6AN VSSC 6AN CLFG and TR CLFG – protection for analogue signals (CL) with floating ground (FG) with and without disconnect lever (TR) Imax 5kA Two stage surge protection with screw connection for instrumentation, control and automation technology • Surge protection in terminal-block format • Modular width of just 6.2 mm • Space saving design: 1 analogue signal • Torx® slotted screw connection • Can be used to comply with the IEC 62305 installation standard and the IEC 61643-1/-22 applications standards. • Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE • Version with floating ground PE connection used to avoid differences in voltage potential • IEC EX/ATEX versions available 1 4 2 5 3 6 TS UNPROTECTED PROTECTED VSSC 6 CLFG 1 4 2 5 3 6 TS UNPROTECTED Similar to illustration Similar to illustration Similar to illustration Technical data General data Nominal current Dielectric strength at FG against PE Volume resistivity Overstressed fault mode Requirement category acc. to IEC 61643-21 Standards Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp (10/350 μs) wire-wire / wire-PE / GND-PE Storage temperature Ambient temperature (operational) Humidity Degree of protection Flammability class Connection data Connection Tightening torque Conductor cross section, flexible, ferrule (DIN 46228-1), max. Conductor cross section, flexible, ferrule (DIN 46228-1), min. Conductor cross section, solid, max. Conductor cross section, solid, min. Conductor cross section, stranded, Rated connection, max. Conductor cross section, stranded, Rated connection, min. Stripping length Mounting rail Dimensions Length x width x height 500 mA (see derating curve) ≥ 500 V / 300 mA (EX Version) 1.8 Ω ± 10 % Mode 2 C2; C3; D1 IEC 61643-21 2.5 kA 50 A 0.5 kA 2.5 kA / 2.5 kA / – 5 kA / 5 kA / – – / 0.5 kA / – -40 °C...+80 °C -40 °C...+70 °C 5...96 % RH IP20 V0 Torx® screw T15 / slot 0.8 x 4 0.5 Nm 4 mm² 0.5 mm² 6 mm² 0.5 mm² 4 mm² 0.5 mm² 10 mm TS35 88.5 x 6.2 x 81 mm PROTECTED VSSC 6 TR CLFG Derating curve I/A 1 0.8 0.6 0.6 0.6 0.6 0.5 0.4 0.4 0.2 0 -40 ºC 0 ºC 15 ºC 42.5 ºC TU 70 ºC Accessories: Screwdriver: Torx® 9009170000, slotted 9008340000; test plug: PS 2.3 0180400000; EMC SET: 1067470000; marker: WS 10/6 1818400000, DEK 6 0468560000, SNAPMARK 1805880000; end plate: 1063110000 This is a graphical representation only. 22 Analogue / Current Loop Protection Analogue / Current Loop Protection | VARITECTOR SSC 6AN PRODUCT SELECTION VSSC 6AN CLFG and TR CLFG Technical data Rated voltage AC/DC Max. continuous voltage UC (AC) / (DC) Signal transmission properties (-3 dB) Pulse reset capacity Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym. Input 1 kV/µs, typ. Protection level on output side unsym., Input 1 kV/µs, typ. Ordering data Type Order No. Note Technical data Rated voltage AC/DC Max. continuous voltage UC (AC) / (DC) Signal transmission properties (-3 dB) Pulse reset capacity Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym. Input 1 kV/µs, typ. Protection level on output side unsym., Input 1 kV/µs, typ. Disconnect lever Testing option Ordering data Type Order No. EX Version Type Order No. Note CLFG 12 V DC CLFG 24 V UC CLFG 48 V UC 12 V DC 15 V DC ≤ 700 kHz ≤ 20 ms ≤ 35 V 35 V / 1600 V / 800 V 24 V AC/ 34 V DC 30 V AC / 42 V DC ≤ 700 kHz ≤ 20 ms ≤ 85 V 90 V / 1632 V / 800 V 48 V AC / 68 V DC 60 V AC / 85 V DC ≤ 700 kHz ≤ 20 ms ≤ 90 V 200 V / 1510 V / 800 V 30 V 70 V 150 V 1600 V 1632 V 1510 V VSSC6 CLFG 12VDC 0.5A 1064260000 VSSC6 CL FG24VUC 0.5A 1064270000 VSSC6 CLFG 48VUC 0.5A 1064280000 TR CLFG 12 V DC TR CLFG 24 V UC TR CLFG 48 V UC 12 V DC 15 V DC ≤ 700 kHz ≤ 20 ms ≤ 35 V 35 V / 1600 V / 800 V 24 V AC / 34 V DC 30 V AC / 42 V DC ≤ 700 kHz ≤ 20 ms ≤ 85 V 90 V / 1632 V / 800 V 48 V AC / 68 V DC 60 V AC / 85 V dc ≤ 700 kHz ≤ 20 ms ≤ 90 V 200 V / 1510 V / 800 V 30 V 70 V 150 V 1600 V 1632 V 1510 V yes Functional screw with test plug receptacle connection 1, 2, 4, 5 yes Functional screw with test plug receptacle connection 1, 2, 4, 5 yes Functional screw with test plug receptacle connection 1, 2, 4, 5 VSSC6 TR CLFG 12Vdc0.5 1064300000 VSSC6TR CLFG 24VUC 0.5A 1064310000 VSSC6TR CLFG 24VUC EX 1066490000 VSSC6 TR CLFG 48VUC 0.5A 1064320000 23 VSPC 2SL – Protection for two binary signals Imax 10kA •Optional monitoring function with status indicator and alert function •Pluggable arrester (plug-in / disconnect interruption-free and impedance neutral) •Testable with V-TEST instrument •Version with non-earthed PE connection for avoiding potential differences •Usable in accordance with installations standard IEC 62305 •Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE • IEC EX/ATEX versions available Technical data GND 11 12 7 8 9 10 GND 3 4 TS 5 6 1 2 unprotected protected Complete module, direct earthing 11 GND 12 7 8 9 10 GND OK FAULT X2 X1 3 4 TS 5 6 1 for all VSPC 2SL Dielectric strength with FG against PE Volume resistivity per path Overstressed fault mode Requirement category acc. to IEC 61643-21 Surge strength C1 Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp. (10/350 μs) wire-wire / wire-PE / GND-PE Type of connection Storage temperature Ambient temperature (operational) Rel. humidity Degree of protection > 500 V / 250 mA (EX Version) 4.7 Ω Mode 2 C1; C2; C3; D1 < 1 kA / 8/20 µs 5 kA / 8/20 µs 100 A / 10/1000 µs 2.5 kA 10/350 µs 2.5 kA / 2.5 kA / 2.5 kA 10 kA / 10 kA / 10kA 2.5 kA / 2.5 kA / 2.5 kA Pluggable in VSPC BASE -40 °C…+80 °C -40 °C…+70 °C 5 %…96 % RH IP20 2 unprotected protected Complete module, direct earthing, with remote alert 11 GND 12 7 8 9 10 GND 0.4 3 4 TS 5 6 1 2 0.35 0.3 unprotected Current [mA] Binary Digital Signal Protection Binary Digital Signal Protection | VARITECTOR SPC protected Complete module, indirect earthing 11 12 7 GND 8 9 0.2 0.15 0.1 10 GND OK FAULT 3 0.25 4 TS 0.05 0 0 5 6 1 unprotected X2 X1 2 protected Complete module, indirect earthing, with remote alert 10 20 30 40 50 60 70 80 90 100 Ambient temperature [°C] Dimensions of complete module (arrester + base element) Length x Width x Height mm Note Without telecomm. contact With telecomm. contact (R) 90 x 17.8 x 69 98 x 17.8 x 69 This is a graphical representation only. Base elements / base to arresters Ordering data for base Type Base element, direct earthing Base element, indirect earthing via spark gap (FG, floating ground) Base element, direct earthing with remote alert Base element, indirect earthing with remote alert EX Base element, indirect earthing via spark gap (FG, floating ground) Note: The basis elements are to be ordered separately VSPC Control unit must be used with remote alert models PG 38. 24 Qty. 1 1 1 1 1 Order No. 8924720000 8924280000 8951770000 8951780000 8951830000 Binary Digital Signal Protection Binary Digital Signal Protection | VARITECTOR SPC VSPC 2SL – arrester / plug-in elements Ordering data Rated voltage UN Max. continuous voltage UC Signaling contact Optical function indicator (VSPC R) Transmission test (-3dB) Impulse reset tested Residual voltage Up wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/μs, typ. input 8/20 μs, typ. Protection level on output side unsym., input 1 kV/μs, typ. input 8/20 μs, typ. Rated current Ordering data Without signaling contact/function indicatorType Order No. With signaling contact/function indicator Type Order No. EX Version Type Order No. Note Ordering data Rated voltage UN Max. continuous voltage UC Signaling contact Optical function indicator (VSPC R) Transmission test (-3dB) Impulse reset tested Residual voltage Up wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/μs, typ. input 8/20 μs, typ. Protection level on output side unsym., input 1 kV/μs, typ. input 8/20 μs, typ. Rated current Ordering data Without signaling contact/function indicatorType Order No. With signaling contact/function indicator Type Order No. EX Version Type Order No. Note VSPC 2SL 5 V DC VSPC 2SL 12 V DC VSPC 2SL 12 V AC VSPC 2SL 24 V DC 5 V DC 6.4 V DC UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 750 KHz 20 ms acc. to IEC61643-21 < 25 V 25 V / 25 V / 25 V 12 V DC 15 V DC UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 750 KHz 20 ms acc. to IEC61643-21 < 50 V 45 V / 50 V / 50 V 12 V AC / 16 V DC 13,2 V AC / 18 V DC no green = OK; red = arrester faulty, replace 750 KHz 20 ms acc. to IEC61643-21 < 50 V 55 V / 50 V / 50 V 24 V DC 28 V DC UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 750 KHz 30 ms acc. to IEC61643-21 < 60 V 80 V / 60 V / 60 V < 25 V < 25 V < 45 V < 45 V < 55 V < 55 V < 80 V < 80 V < 12 V < 25 V 300 mA < 25 V < 50 V 300 mA < 30 V < 50 V 300 mA < 40 V < 60 V 300 mA VSPC 2SL 5VDC 0.5A 8924210000 VSPC 2SL 5VDC 0.5A R 8951610000 VSPC 2SL 12VDC 0.5A 8924230000 VSPC 2SL 12VDC 0.5A R 8951620000 VSPC 2SL 12VDC EX 8953620000 VSPC 2SL 12VAC 0.5A 8924250000 VSPC 2SL 24VDC 0.5A 8924330000 VSPC 2SL 24VDC 0.5A R 8951630000 VSPC 2SL 24VDC EX 8953670000 VSPC 2SL 12VAC EX 8953630000 VSPC 2SL 24 V AC VSPC 2SL 48 V AC 24 V AC / 34 V DC 28 V AC / 39 V DC UN 250 V AC 0,1 A 1CO at VSPC R with VSPC CONTROL UNIT 48 V AC / 68 V DC 60 V AC / 85 V DC no green = OK; red = arrester faulty, replace green = OK; red = arrester faulty, replace 750 KHz 60 ms acc. to IEC61643-21 < 60 V 80 V / 60 V / 60 V 750 KHz 60 ms acc. to IEC61643-21 < 125 V 80 V / 125 V / 125 V < 110 V < 80 V < 210 V < 80 V < 60 V < 60 V 300 mA < 85 V < 125 V 250 mA VSPC 2SL 24VAC 0.5A 8924350000 VSPC 2SL 24VAC 0.5A R 8951640000 VSPC 2SL 48VAC 0.5A 8924370000 VSPC 2SL 48VAC EX 8953640000 25 VSPC 4SL – Protection for four binary signals Imax 10kA •Optional monitoring function with status indicator and alert function •Pluggable arrester (plug-in / disconnect interruption-free and impedance neutral) •Testable with V-TEST instrument •Space-saving design for four binary signals with signaling contact, without additional space requirements •Version with non-earthed PE connection for avoiding potential differences •Usable in accordance with installations standard IEC 62305 •Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE • IEC EX/ATEX versions available Technical data GND 11 12 7 8 9 10 GND 3 4 TS 5 6 1 2 unprotected protected Complete module, direct earthing 11 GND 12 7 8 9 10 GND OK FAULT 3 X2 X1 4 TS 5 for all VSPC 4SL Volume resistivity per path Overstressed fault mode Requirement category acc. to IEC 61643-21 Surge strength C1 Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp. (10/350 μs) wire-wire / wire-PE / GND-PE Type of connection Storage temperature Ambient temperature (operational) Rel. humidity Degree of protection 4.7 Ω Mode 2 C1; C2; C3; D1 < 1 kA / 8/20 µs 5 kA / 8/20 µs 100 A / 10/1000 µs 2.5 kA 10/350 µs 2.5 kA / 2.5 kA / 2.5 kA 10 kA / 10 kA / 10 kA 2.5 kA / 2.5 kA / 2.5 kA Pluggable in VSPC BASE -40 °C … +80 °C -40 °C … +70 °C 5 % … 96 % RH IP20 6 1 2 unprotected protected Complete module, direct earthing, with remote alert 11 GND 12 7 8 9 10 GND 3 4 0.4 TS 5 6 1 2 0.35 0.3 unprotected Current [mA] Binary Digital Signal Protection Binary Digital Signal Protection | VARITECTOR SPC protected Complete module, indirect earthing 11 GND 12 0.25 0.2 0.15 0.1 7 8 9 10 GND 0.05 X2 X1 0 OK FAULT 3 4 TS 5 6 1 2 unprotected protected Complete module, indirect earthing, with remote alert 0 10 20 30 40 50 60 70 80 90 100 Ambient temperature [°C] Dimensions of complete module (arrester + base element) Length x Width x Height mm Note Without telecomm. contact With telecomm. contact (R) 90 x 17.8 x 69 98 x 17.8 x 69 This is a graphical representation only. Base elements / base to arresters Ordering data for base Type Base element, direct earthing Base element, indirect earthing via spark gap (FG, floating ground) Base element, direct earthing with remote alert Base element, indirect earthing with remote alert EX Base element, indirect earthing via spark gap (FG, floating ground) Note: The basis elements are to be ordered separately VSPC Control unit must be used with remote alert models PG 38. 26 Qty. 1 1 1 1 1 Order No. 8924700000 8924260000 8951750000 8951760000 8951840000 Binary Digital Signal Protection Binary Digital Signal Protection | VARITECTOR SPC VSPC 4SL – arrester / plug-in elements Ordering data Rated voltage UN Max. continuous voltage UC Signaling contact Optical function indicator (VSPC R) Transmission test (-3dB) Impulse reset tested Residual voltage Up wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/μs, typ. input 8/20 μs, typ. Protection level on output side unsym., input 1 kV/μs, typ. input 8/20 μs, typ. Rated current Ordering data Without signaling contact/function indicatorType Order No. With signaling contact/function indicator Type Order No. EX Version Type Order No. Note Ordering data Rated voltage UN Max. continuous voltage UC Signaling contact Optical function indicator (VSPC R) Transmission test (-3dB) Impulse reset tested Residual voltage Up wire-wire / wire-PE / GND-PE Protection level on output side sym., input 1 kV/μs, typ. input 8/20 μs, typ. Protection level on output side unsym., input 1 kV/μs, typ. input 8/20 μs, typ. Rated current Ordering data Without signaling contact/function indicatorType Order No. With signaling contact/function indicator Type Order No. EX Version Type Order No. Note VSPC 4SL 5 V DC VSPC 4SL 12 V DC VSPC 4SL 12 V AC VSPC 4SL 24 V DC 5 V DC 6.4 V DC UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 730 KHz 20 ms acc. to IEC61643-21 < 25 V 25 V / 25 V / 25 V 12 V DC 15 V DC UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 750 KHz 20 ms acc. to IEC61643-21 < 35 V 45 V / 20 V / 450 V 12 V AC / 16 V DC 13.2 V AC / 18 V DC no 24 V DC green = OK; red = arrester faulty, replace 750 KHz 20 ms acc. to IEC61643-21 < 50 V 55 V / 50 V / 50 V < 25 V < 25 V < 45 V < 45 V < 55 V < 55 V < 80 V < 80 V < 12 V < 25 V 350 mA < 25 V < 50 V 300 mA < 30 V < 50 V 300 mA < 40 V < 60 V VSPC 4SL 5VDC 0.5A 8924200000 VSPC 4SL 5VDC 0.5A R 8951570000 VSPC 4SL 12VDC 0.5A 8924220000 VSPC 4SL 12VDC 0.5A R 8951580000 VSPC 4SL 12VDC EX 1161170000 VSPC 4SL 12VAC 0.5A 8924240000 28 V DC UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 750 KHz 30 ms acc. to IEC61643-21 < 60 V 80 V / 60 V / 60 V 300 mA VSPC 4SL 24VDC 0.5A 8924320000 VSPC 4SL 24VDC 0.5A R 8951590000 VSPC 4SL 24VDC EX 1161190000 VSPC 4SL 12VAC EX 1161150000 VSPC 4SL 24 V AC VSPC 4SL 48 V AC 24 V AC / 34 V DC 28 V AC / 39 V DC UN 250 V AC 0.1 A 1CO at VSPC R with VSPC CONTROL UNIT 48 V AC / 68 V DC 60 V AC / 85 V DC no green = OK; red = arrester faulty, replace green = OK; red = arrester faulty, replace 750 KHz 40 ms acc. to IEC61643-21 < 60 V 80 V / 60 V / 60 V 750 KHz 60 ms acc. to IEC61643-21 < 125 V 80 V / 125 V / 125 V < 110 V < 80 V < 210 V < 80 V < 60 V < 60 V 300 mA < 85 V < 125 V 250 mA VSPC 4SL 24VAC 0.5A 8924340000 VSPC 4SL 24VAC 0.5A R 8951600000 VSPC 4SL 24VAC EX 1161180000 VSPC 4SL 48VAC 0.5A 8924360000 27 VARITECTOR SSC 4 SL and SL FG Imax 10kA Two-stage surge protection with screw connection for instrumentation, control and automation technology •Surge protection in terminal-block format •Modular width of just 6.2 mm •Space-saving design: 1 binary signal •Torx slotted screw connection •Version with non-earthed PE connection for avoiding potential differences •Usable in accordance with installations standard IEC 62305 •Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE • IEC EX/ATEX versions available Technical data 1 2 General data Nominal current IN at 25 °C Rated discharge current IN (8 / 20 µs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8 / 20 µs) wire-wire / wire-PE / GND-PE Response time wire-wire / wire-PE / GND-PE Volume resistivity per path Discharge current Itotal Rated discharge current Iimp (10 / 350 µs) Surge strength Max. continuous voltage Overstressed fault mode Requirement category acc. to IEC 61643-21 Rel. humidity Degree of protection Ambient temperature (operational) Storage temperature Approvals Clampable conductor Connection Stripping length Tightening torque range Solid / stranded Flexible / flexible with ferrule 3 4 TS unprotected protected VSSC4 SL 3 1 2 4 TS protected unprotected 500 mA / 300 mA (EX Version) - / 2.5 kA / - / 10 kA / - / ≤ 2 ns / ≤ 100 ns 1.8 Ω ± 10% 10 kA 1 kA 4 kV / 2 kA, 10 repetitions 1 A / 1 s, 5 repetitions Mode 2 C1; C2; C3; D1 5%…96% RH IP20 -40 °C…+70 °C -40 °C…+80 °C UL, CSA pending Torx screw (T15) / slot (0.8 x 4.0) 7 mm 0.5 … 0.8 Nm 0.5 … 6 mm² / 0.5 … 4 mm² 0.5 … 2.5 mm² Dimensions Length x Width x Height mm Note: end plate AP VSSC4: 1063120000 VSSC SL FG This is a graphical representation only. 76 x 6.2 x 58.5 Applications 1 Load current I [A] Binary Digital Signal Protection Binary Digital Signal Protection | VARITECTOR SSC 4AN 0.8 0.6 0.4 0.4 0.2 0 -40 0 15 42.5 Ambient temperature T [°C] 28 70 Binary Digital Signal Protection Binary Digital Signal Protection | VARITECTOR SSC 4AN PRODUCT SELECTION VARITECTOR SSC 4 SL and SL FG Ordering data Rated voltage UN Max. continuous voltage UC Voltage GND-PE Capacitance Gas discharge tube Supressordiode UP Limiting frequency (-3 dB) at load resistance Protection level at IN wire-wire / wire-PE / GND-PE 1 kV / µs wire-wire / wire-PE / GND-PE Ordering data Type Order No. Note Ordering data Rated voltage UN Max. continuous voltage UC Voltage GND-PE Capacitance Gas discharge tube Supressordiode UP Limiting frequency (-3 dB) at load resistance Protection level at IN wire-wire / wire-PE / GND-PE 1 kV / µs wire-wire / wire-PE / GND-PE Ordering data Type Order No. EX Version Type Order No. Note VSSC4 SL 12 V DC 0.5 A VSSC4 SL FG 12 V DC 0.5 A VSSC4 SL 24 V UC 0.5 A 12 V DC 15 V DC 4 nF 90 V 16 V 250 KHz 12 V DC 15 V DC > 500 V 4 nF 90 V 16 V 250 KHz 24 V AC / 34 V DC 30 V AC / 42 V DC 650 pF 90 V 43 V 1.5 MHz - / 35 V / - / 30 V / - - / 35 V / 1400 V - / 30 V / 1400 V - / 90 V / - / 70 V / - VSSC4 SL 12VDC 0.5A 1063830000 VSSC4 SL FG 12VDC 0.5A 1063880000 VSSC4 SL 24VUC 0.5A 1063840000 VSSC4 SL FG 24 V UC 0.5 A VSSC4 SL 48 V UC 0.5 A VSSC4 SL FG 48 V UC 0.5 A 24 V AC / 34 V DC 30 V AC / 42 V DC > 500 V 650 pF 90 V 43 V 1.5 MHz 48 V AC / 68 V DC 60 V AC / 85 V DC 450 pF 150 V 91 V 2.2 MHz 48 V AC / 68 V DC 60 V AC / 85 V DC > 500 V 450 pF 150 V 91 V 2.2 MHz - / 90 V / 1400 V - / 70 V / 1400 V - / 200 V / - / 150 V / - - / 200 V / 1200 V - / 150 V / 1200 V VSSC4 SL FG 24VUC 0.5A 1063890000 VSSC4 SL FG 24VUC EX 1063930000 VSSC4 SL 48VUC 0.5A 1063860000 VSSC4 SL FG 48VUC 0.5A 1063910000 VSSC4 SL FG 48VUC EX 1063940000 29 Binary Digital Signal Protection Binary Digital Signal Protection | VARITECTOR SSC 6AN VSSC 6AN SL and TR SL – protection for binary signals (SL) with disconnect lever (TR) and indicator (LD) Imax 10kA Two-stage surge protection with screw connection for instrumentation, control and automation technology •Surge protection in terminal-block format •Modular width of just 6.2 mm •Space saving design: 2 binary signals •Torx® slotted screw connection •Can be used to comply with the IEC 62305 installation standard and the IEC 61643-1/-22 applications standards •Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE Similar to illustration Similar to illustration Similar to illustration Technical data 1 4 3 6 2 5 TS UNPROTECTED PROTECTED VSSC 6 SLLD 1 4 3 6 2 General data Nominal current Dielectric strength at FG against PE Volume resistivity Overstressed fault mode Requirement category acc. to IEC 61643-21 Standards Surge strength C2 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp (10/350 μs) wire-wire / wire-PE / GND-PE Storage temperature Ambient temperature (operational) Humidity Degree of protection Flammability class Connection data Connection Tightening torque Conductor cross section, flexible, ferrule (DIN 46228-1), max. Conductor cross section, flexible, ferrule (DIN 46228-1), min. Conductor cross section, solid, max. Conductor cross section, solid, min. Conductor cross section, stranded, Rated connection, max. Conductor cross section, stranded, Rated connection, min. Stripping length Mounting rail Dimensions Length x width x height 500 mA (see derating curve) – 1.8 Ω ± 10 % Mode 2 C2; C3; D1 IEC 61643-21 2.5 kA 1 kA – / 2.5 kA / – – / 10 kA / – – / 1 kA / – -40 °C...+80 °C -40 °C...+70 °C 5...96 % RH IP20 V0 Torx® screw T15 / slot 0.8 x 4 0.5 Nm 4 mm² 0.5 mm² 6 mm² 0.5 mm² 4 mm² 0.5 mm² 10 mm TS35 88.5 x 6.1 x 81 mm 5 TS UNPROTECTED PROTECTED VSSC 6 TR SLLD Derating curve I/A 1 0.8 0.6 0.6 0.6 0.6 0.5 0.4 0.4 0.2 0 -40 ºC 0 ºC This is a graphical representation only. 30 15 ºC 42.5 ºC TU 70 ºC Accessories: Screwdriver: Torx® 9009170000, slotted 9008340000; test plug: PS 2.3 0180400000; EMC SET: 1067470000; marker: WS 10/6 1818400000, DEK 6 0468560000, SNAPMARK 1805880000; end plate: 1063110000 Binary Digital Signal Protection Binary Digital Signal Protection | VARITECTOR SSC 6AN PRODUCT SELECTION VSSC 6AN SL and TR SL Technical data Rated voltage AC/DC Max. continuous voltage UC (AC) / (DC) Signal transmission properties (-3 dB) Pulse reset capacity Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym. Input 1 kV/µs, typ. Protection level on output side unsym., Input 1 kV/µs, typ. Surge strength C3 Status indicator Ordering data Type Order No. Note Technical data Rated voltage AC/DC Max. continuous voltage UC (AC) / (DC) Signal transmission properties (-3 dB) Pulse reset capacity Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym. Input 1 kV/µs, typ. Protection level on output side unsym., Input 1 kV/µs, typ. Surge strength C3 Disconnect lever Testing option Status indicator Ordering data Type Order No. Note SL LD 12 V DC SL LD 24 V UC SL LD 48 V UC 12 V DC 15 V DC ≤ 700 kHz ≤ 30 ms ≤ 40 V - / 74 V / - 24 V AC / 34 V DC 30 V AC / 42 V DC ≤ 700 kHz ≤ 30 ms ≤ 100 V - / 110 V / - 48 V AC/ 68 V DC 60 V AC / 85 V DC ≤ 700 kHz ≤ 30 ms ≤ 220 V - / 175 V / - - - - 74 V 10 A Yes 110 V 50 A Yes 175 V 50 A Yes VSSC6 SL LD 12VDC 0.5A 1064340000 VSSC6 SL LD 24VUC 0.5A 1064350000 VSSC6 SL LD 48VUC 0.5A 1064360000 TR SL LD 12 V DC TR SL LD 24 V UC TR SL LD 48 V UC 12 V DC 15 V DC ≤ 700 kHz ≤ 30 ms ≤ 40 V - / 74 V / - 24 V AC / 34 V DC 30 V AC / 42 V DC ≤ 700 kHz ≤ 30 ms ≤ 100 V - / 110 V / - 48 V AC/ 68 V DC 60 V AC / 85 V DC ≤ 700 kHz ≤ 30 ms ≤ 220 V - / 175 V / - - - - 74 V 10 A Yes Functional screw with test plug receptacle connection 1, 2, 4, 5 Yes 110 V 50 A Yes Functional screw with test plug receptacle connection 1, 2, 4, 5 Yes 175 V 50 A Yes Functional screw with test plug receptacle connection 1, 2, 4, 5 Yes VSSC6 TR SL LD12Vdc0.5A 1064380000 VSSC6 TR SL LD 24VUC 0.5A 1064390000 VSSC6 TR SL LD 48VUC 0.5A 1064400000 31 Binary Digital Signal Protection Binary Digital Signal Protection | VARITECTOR SSC 6AN VSSC 6AN SLFG and TR SLFG – protection for binary signals (SL) with floating ground (FG), with and without disconnect lever (TR) and indicator (LD) Two stage surge protection with screw connection for instrumentation, control and automation technology •Surge protection in terminal block format •Modular width of just 6.2 mm •Space saving design: 2 binary signals •Torx® slotted screw connection •Can be used to comply with the IEC 62305 installation standard and the IEC 61643-1/-22 applications standards •Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE •Version with floating ground PE connection used to avoid differences in voltage potential Imax 10kA Similar to illustration Similar to illustration Similar to illustration Similar to illustration Technical data 1 4 3 6 2 General data Dielectric strength at FG against PE Volume resistivity Overstressed fault mode Requirement category acc. to IEC 61643-21 Standards Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp (10/350 μs) wire-wire / wire-PE / GND-PE Storage temperature Ambient temperature (operational) Humidity Degree of protection Flammability class Connection data Connection Tightening torque Conductor cross section, flexible, ferrule (DIN 46228-1), max. Conductor cross section, flexible, ferrule (DIN 46228-1), min. Conductor cross section, solid, max. Conductor cross section, solid, min. Conductor cross section, stranded, Rated connection, max. Conductor cross section, stranded, Rated connection, min. Stripping length Mounting rail Dimensions Length x width x height 5 TS UNPROTECTED PROTECTED VSSC 6 SLFG 1 4 3 6 2 ≥ 500 V 1.8 Ω ± 10 % Mode 2 C2; C3; D1 IEC 61643-21 2.5 kA 10 A; 50 A @ 60 V 1 kA – / 2.5 kA / 2.5 kA – / 10 kA / 10 kA – / 10 kA / – -40 °C...+80 °C -40 °C...+70 °C 5...96 % RH IP20 V0 Torx® screw T15 / slot 0.8 x 4 0.5 Nm 4 mm² 0.5 mm² 6 mm² 0.5 mm² 4 mm² 0.5 mm² 10 mm TS35 88.5 x 6.2 x 81 mm 5 TS UNPROTECTED PROTECTED VSSC 6 TR SLFGLD Derating curve I/A 1 0.8 0.6 0.6 0.6 0.6 0.5 0.4 0.4 0.2 0 -40 ºC 0 ºC This is a graphical representation only. 32 15 ºC 42.5 ºC TU 70 ºC Accessories: Screwdriver: Torx® 9009170000, slotted 9008340000; test plug: PS 2.3 0180400000; EMC SET: 1067470000; marker: WS 10/6 1818400000, DEK 6 0468560000, SNAPMARK 1805880000; end plate: 1063110000 Binary Digital Signal Protection Binary Digital Signal Protection | VARITECTOR SSC 6AN PRODUCT SELECTION VSSC 6AN SLFG and TR SLFG Technical data Rated voltage AC/DC Max. continuous voltage UC (AC) / (DC) Signal transmission properties (-3 dB) Pulse reset capacity Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym. Input 1 kV/µs, typ. Protection level on output side unsym., Input 1 kV/µs, typ. Nominal current Status indicator Ordering data Type Order No. Note Technical data Rated voltage AC/DC Max. continuous voltage UC (AC) / (DC) Signal transmission properties (-3 dB) Pulse reset capacity Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym. Input 1 kV/µs, typ. Protection level on output side unsym., Input 1 kV/µs, typ. Nominal current Disconnect lever Testing option Status indicator Ordering data Type Order No. Note SLFG LD 12 V DC SLFG LD 24 V UC SLFG LD 48 V UC 12 V DC 15 V DC ≤ 700 kHz ≤ 20 ms ≤ 1600 V - / 74 V / 1400 V 24 V AC / 34 V DC 30 V AC / 42 V DC ≤ 700 kHz ≤ 20 ms ≤ 1650 V - / 110 V / 1400 V 48 V AC / 68 V DC 60 V AC / 85 V DC ≤ 700 kHz ≤ 20 ms ≤ 1550 V - / 175 V / 1200 V 30 V 70 V 150 V 74 V 500 mA yes 110 V 200 mA (IEC 61643-21) yes 175 V on request yes VSSC6 SLFG 12VDC 0.5A 1064420000 VSSC6 SLFG 24VUC 0.5A 1064430000 VSSC6 SLFG 48VUC 0.5A 1064440000 TR SLFG LD 12 V DC TR SLFG LD 24 V UC TR SLFG LD 48 V UC 12 V DC 15 V DC ≤ 700 kHz ≤ 20 ms ≤ 1600 V - / 74 V / 1400 V 24 V AC / 34 V DC 30 V AC / 42 V DC ≤ 700 kHz ≤ 20 ms ≤ 1650 V - / 110 V / 1400 V 48 V AC / 68 V DC 60 V AC / 85 V DC ≤ 700 kHz ≤ 20 ms ≤ 1550 V - / 175 V / 1200 V 30 V 70 V 150 V 74 V 500 mA Yes Functional screw with test plug receptacle connection 1, 2, 4, 5 Yes 110 V 200 mA (IEC 61643-21) Yes Functional screw with test plug receptacle connection 1, 2, 4, 5 Yes 175 V on request Yes Functional screw with test plug receptacle connection 1, 2, 4, 5 Yes VSSC6 TR SLFG LD 12VDC 0.5A 1064490000 VSSC6 TR SLFG LD 24VUC 0.5A 1064500000 VSSC6 TR SL FG LD 48VUC 0.5A 1064510000 33 VSPC RS485 Imax 10kA For serial data transmission •Optional monitoring function with status indicator and alert function •Pluggable arrester (plug-in / disconnect interruption-free and impedance neutral) •Low residual voltage •Protection for conducted serial data transmission – RS485 •Testable with V-TEST instrument •Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE Technical data GND 11 12 7 8 9 3 unprotected 10 GND 4 TS 5 6 1 2 protected Complete module, direct earthing 11 GND 12 7 8 9 10 GND OK FAULT 3 unprotected X2 X1 4 TS 5 6 1 2 for all VSPC RS485 Dielectric strength with FG against PE Rated current Volume resistivity per path Overstressed fault mode Requirement category acc. to IEC 61643-21 Surge strength C1 Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp. (10/350 μs) wire-wire / wire-PE / GND-PE Type of connection Storage temperature Ambient temperature (operational) Rel. humidity Degree of protection > 500 V 450 mA 2.2 Ω Mode 2 C1; C2; C3; D1 < 1 kA / 8/20 µs 5 kA / 8/20 µs 100 A / 10/1000 µs 2.5 kA 10/350 µs 2.5 kA / 2.5 kA / 2.5 kA 10 kA / 2 x 10 kA / 10 kA 0.2 kA / 2 x 0.2 kA / 0.2 kA Pluggable in VSPC BASE -40 °C…+80 °C -40 °C…+70 °C 5 %…96 % RH IP20 protected Complete module, direct earthing, with remote alert 11 12 7 8 9 10 GND 0.5 GND 0.45 3 unprotected 4 TS 5 6 1 2 0.4 protected Complete module, indirect earthing 11 12 7 8 Current [mA] Other Communication Types Other Communication Types | VARITECTOR SPC 0.35 0.3 0.25 0.2 0.15 0.1 0.05 GND 9 10 GND OK FAULT 3 unprotected TS X2 X1 0 0 5 6 1 2 Complete module, indirect earthing, with remote alert protected 10 20 30 40 50 60 70 80 90 100 Temperature [°C] 4 Dimensions of complete module (arrester + base element) Length x Width x Height mm Note Without telecomm. contact With telecomm. contact (R) 90 x 17.8 x 69 98 x 17.8 x 69 This is a graphical representation only. Base elements / base to arresters Ordering data for base Type Base element, direct earthing Base element, indirect earthing via spark gap (FG, floating ground) Base element, direct earthing with remote alert Base element, indirect earthing with remote alert Note: The basis elements are to be ordered separately VSPC Control unit must be used with remote alert models PG 38. 34 Qty. 1 1 1 1 Order No. 8924710000 8924270000 8951790000 8951800000 Other Communication Types Other Communication Types | VARITECTOR SPC VSPC RS485 – arrester / plug-in elements Ordering data VSPC RS485 2CH Rated voltage (DC) Max. continuous voltage, UC (DC) Signaling contact Optical function indicator (VSPC R) Transmission test (-3dB) Impulse reset tested Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym., Protection level on output side unsym., Ordering data Without signaling contact / Function indicator With signaling contact / Function indicator Note input 1 kV/μs, typ. input 8/20 μs, typ. input 1 kV/μs, typ. input 8/20 μs, typ. Type Order No. Type Order No. 5 V DC 6,4 V DC UN 250 V AC 0,1 A 1CO at VSPC R with VSPC CONTROL UNIT green = OK; red = arrester faulty, replace 4 MHz 20 ms acc. to IEC61643-21 35 V 15 V / 35 V / 500 V < 10 V < 15 V < 10 V < 35 V VSPC RS485 2CH 8924670000 VSPC RS485 2CH R 8951670000 35 Other Communication Types Other Communication Types | VARITECTOR SSC 6AN VSSC 6AN RS485, RS485 DP and RS232 – for interface signals Two-stage surge protection with screw connection for instrumentation, control and automation technology •Surge protection in terminal block format •Modular width of just 6.2 mm •Space saving design •Torx® slotted screw connection •Can be used to comply with the IEC 62305 installation standard and the IEC 61643-1/-22 applications standards •Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE • IEC EX/ATEX versions available Imax 10kA Similar to illustration Similar to illustration Technical data 1 4 3 6 2 5 TS UNPROTECTED PROTECTED 1 4 3 6 2 5 TS UNPROTECTED 500 mA (see derating curve) / 300 mA (EX Version) 1.8 Ω ±10 % Mode 2 C2, C3, D1 IEC 61643-21 2.5 kA 10 A 0.5 kA 2.5 kA / 2.5 kA / – 10 kA / 10 kA / – 1 kA -40 °C...+80 °C -40 °C...+70 °C 5...96 % RH IP20 V0 Torx® screw T15 / slot 0.8 x 4 0.5 Nm 4 mm² 0.5 mm² 6 mm² 0.5 mm² 4 mm² 0.5 mm² 10 mm TS35 88.5 x 6.2 x 81 mm Accessories: Screwdriver: Torx® 9009170000, slotted 9008340000; test plug: PS 2.3 0180400000; EMC SET: 1067470000; marker: WS 10/6 1818400000, DEK 6 0468560000, SNAPMARK 1805880000; end plate: 1063110000 PROTECTED Technical data Derating curve I/A General data Nominal current Volume resistivity Overstressed fault mode Requirement category to IEC 61643-21 Standards Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp (10/350 μs) wire-wire / wire-PE / GND-PE Storage temperature Ambient temperature (operational) Humidity Degree of protection Flammability class Connection data Connection Tightening torque Conductor cross section, flexible, ferrule (DIN 46228-1), max. Conductor cross section, flexible, ferrule (DIN 46228-1), min. Conductor cross section, solid, max. Conductor cross section, solid, min. Conductor cross section, stranded, Rated connection, max. Conductor cross section, stranded, Rated connection, min. Stripping length Mounting rail Dimensions Length x width x height RS485 RS232 12 V DC 15 V DC ≤ 2 MHz ≤ 20 ms ≤ 94 V 35 V / 35 V / - 12 V DC 15 V DC ≤ 2 MHz ≤ 20 ms ≤ 80 V 70 V / 35 V / - 30 V 60 V 94 V 80 V VSSC6 RS485 1064980000 VSSC6 RS485 EX 1065020000 VSSC6 RS232 1064990000 1 0.8 0.6 0.6 0.6 0.6 0.5 0.4 0.4 0.2 0 -40 ºC 0 ºC 15 ºC 42.5 ºC TU 70 ºC Rated voltage AC/DC Max. continuous voltage UC (DC) Signal transmission properties (-3 dB) Pulse reset capacity Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym. Input 1 kV/µs, typ. Protection level on output side unsym., Input 1 kV/µs, typ. This is a graphical representation only. 36 Ordering data Type Order No. EX Version Type Order No. Note VSSC 6AN RTD – for temperature signals Other Communication Types Other Communication Types | VARITECTOR SSC 6AN Imax 10kA Two-stage surge protection with screw connection for instrumentation, control and automation technology •Surge protection in terminal block format •Modular width of just 6.2 mm •Space saving design •Torx® slotted screw connection •Can be used to comply with the IEC 62305 installation standard and the IEC 61643-1/-22 applications standards •Integrated PE contact in base element, safely discharges up to 20 kA (8/20 μs) and 2.5 kA (10/350 μs) to PE • IEC EX/ATEX versions available Similar to illustration Similar to illustration Technical data 1 4 2 5 3 6 TS UNPROTECTED PROTECTED General data Nominal current Dielectric strength at FG against PE Volume resistivity Overstressed fault mode Requirement category acc. to IEC 61643-21 Standards Surge strength C2 Surge strength C3 Surge strength D1 Rated discharge current IN (8/20 μs) wire-wire / wire-PE / GND-PE Rated discharge current Imax (8/20 μs) wire-wire / wire-PE / GND-PE Lightning test current, Iimp (10/350 μs) wire-wire / wire-PE / GND-PE Storage temperature Ambient temperature (operational) Humidity Degree of protection Flammability class Connection data Connection Tightening torque Conductor cross section, flexible, ferrule (DIN 46228-1), max. Conductor cross section, flexible, ferrule (DIN 46228-1), min. Conductor cross section, solid, max. Conductor cross section, solid, min. Conductor cross section, stranded, Rated connection, max. Conductor cross section, stranded, Rated connection, min. Stripping length Mounting rail Dimensions Length x width x height 300 mA – 1.8 Ω ±10 % Mode 2 C2, C3, D1 IEC 61643-21 2.5 kA 8/20 µs, 5 kV 1,2/50 µs 10 A 10/1000 µs 0.5 kA 10/350 µs 2.5 kA / 2.5 kA / – 10 kA / 10 kA / – 1 kA -40 °C...+80 °C -40 °C...+70 °C 5...96 % RH IP20 V0 Torx® screw T15 / slot 0.8 x 4 0.5 Nm 4 mm² 0.5 mm² 6 mm² 0.5 mm² 4 mm² 0.5 mm² 10 mm TS35 88.5 x 6.2x 81 mm Accessories: Screwdriver: Torx® 9009170000, slotted 9008340000; test plug: PS 2.3 0180400000; EMC SET: 1067470000; marker: WS 10/6 1818400000, DEK 6 0468560000, SNAPMARK 1805880000; end plate: 1063110000 Technical data Rated voltage AC/DC Max. continuous voltage UC (DC) Signal transmission properties (-3 dB) Pulse reset capacity Residual voltage UP wire-wire / wire-PE / GND-PE Protection level on output side sym. Input 1 kV/µs, typ. Protection level on output side unsym., Input 1 kV/µs, typ. This is a graphical representation only. Ordering data Type Order No. EX Version Type Order No. Note RTD 1 V DC 5 V DC ≤ 1 MHz ≤ 20 ms ≤ 126 V 15 V / 15 V / 10 V 10 V VSSC6 RTD 1139710000 VSSC6 RTD EX 1130670000 37 Accessories | VARITECTOR SPC Accessories VSPC CONTROL UNIT 24 V DC •For monitoring up to 10 protective modules •Signaling module for all VSPCs with status indicator •Signaling of cable breaks / signal interruptions •Voltage supply from 18...31 V DC •Potential-free changeover contact •Function indicator (red/green LED) Technical data X2 24 V X1 0V 12 11 14 VSPC CONTROL UNIT X2 X2 X1 X2 X1 X1 nmax = 10 n=2 n=1 VSPC...R VSPC...R VSPC...R Input Rated voltage (DC) Rated current Power rating Output Current loop Monitoring option Signal output Type Max. switching voltage / continuous current Diagnostics Operating status Defect at current loop Wire breakage General data Terminal rail Design, Protection class Type of connection Storage temperature Ambient temperature (operational) Rel. humidity Start-up time after fault correction Dimensions Length x Width x Height mm Note This is a graphical representation only. Application Ordering data 18 V…24 V DC…31 V DC max. 50 mA 1.5 W 8 mA bei < 51 V 1…10 VSPC modules 1 CO contact 250 V / 1 A Green LED Red LED (control unit and defective module) Red/green LED, flashing TS35 Insta-enclosure, IP20 BL / SL -40 °C…+80 °C -40 °C…+70 °C 5 %…96 % RH 60 s 102 x 18 x 71.5 VSPC CONTROL UNIT 24 V DC l ≤ 3 meter Type Order No. Note n x VSPC...R VSPC CONTROL UNIT n ≤ 10 Status indication LED green LED red Function OK FAULT (one/several defect VSPC…R) Wire break in monitoring current loop 38 VSPC CONTROL UNIT 24Vdc 8972270000 Accessories | VARITECTOR SPC AND ACCESSORIES VSPC accessories Accessories V-Test •Instrument for testing the protective functions of series: PU I, PU II and VSPC •Device for realising standard IEC 62305 (periodic testing) •Handy device with integrated battery set for local measurements •Result display via LCD display •Bilingual menu •Including protective bag and power supply •Intuitive user navigation in German and English The V-Test is a compact, portable instrument for the Varitector SPC pluggable surge protection (VSPC series) and surge protection for power distribution, PUI and II series. With this instrument, the Weidmüller surge protection can be tested for protective function in accordance with the required test periods as stipulated by IEC62305 (DIN VDE 185 Part 3). In a backlit display, the measurement result is indicated with „ok“ or „not ok“ for each component. Technical data Ordering data Rated voltage Accumulator set Storage temperature Ambient temperature (operational) Degree of protection Measuring range UL94 flammability class 100...240 V AC 8 NiMH with 2600 mA 0 °C ... 40 °C 0 °C ... 40 °C IP20 U < 1000 V / I = 1 mA V0 General tolerances of measurement range Gas discharge tube Varistor TVS-diode +/- 10% +/- 5% +/- 5% Dimensions Length x Width x Height mm Ordering data Type Order No. Accessories Dimensions Test Plug 2.3mm Torx Screwdriver 0.8x4x100mm Note Note Custom Print Identification System EMC Set Ordering data Type SNAPMARK 1 WS 10/5 VSSC6 Side Labels WS 10/6 VSPC DEK 5/5 Note V-Test 230 x 122 x 65 V-Test 8951860000 0180400000 9008340000 Ordering data Material Qty. 50 144 Order No. 1805880000 1635010000 120 1818410000 200 1609810000 Shield connection: Complete set - cable ties and shield connection Cable ties Shield connection Cable tie tool Type Qty. EMC set 1 EMC tie 100 EMC connector 50 Cable tie tool RT-1 1 Note Order No. 1067470000 1067490000 1067520000 1296000000 39 Weidmüller – Partner in Industrial Connectivity. As experienced experts we support our customers and partners around the world with products, solutions and services in the industrial environment of power, signal and data. We are at home in their industries and markets and know the technological challenges of tomorrow. We are therefore continuously developing innovative, sustainable and useful solutions for their individual needs. Together we set standards in Industrial Connectivity. For all Weidmüller Product Distibutors please visit www.weidmuller.com.au/au/distributors Or contact your preferred supplier below: Weidmüller Pty Ltd (Head Office) 43 Huntingwood Drive, Huntingwood NSW 2148 Phone +61 (0) 2 9671 9999 Fax +61 (0) 2 9671 9900 Email [email protected] www.weidmuller.com.au WAUS Surge Protection 2012-2013