TE Analog Devices Welcomes Hittite Microwave Corporation O B SO LE NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com TE O B SO LE THIS PAGE INTENTIONALLY LEFT BLANK HMC467LP3 / 467LP3E v01.0705 2 dB LSB GaAs MMIC 2-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 6 GHz ATTENUATORS - SMT 5 Typical Applications Features The HMC467LP3 / HMC467LP3E is ideal for: 2 dB LSB Steps to 6 dB • Cellular; UMTS/3G Infrastructure High IP3: +50 dBm • Fixed Wireless & WLL ± 0.2 dB Typical Bit Error • Microwave Radio & VSAT Single Control Line Per Bit Single +5V Supply TE • Test Equipment 3x3 mm SMT Package General Description Functional Diagram B SO LE The HMC467LP3 & HMC467LP3E are broadband 2-bit GaAs IC digital attenuators in low cost leadless surface mount packages. Covering DC to 6.0 GHz, the insertion loss is less than 0.7 dB typical. The attenuator bit values are 2 (LSB) and 4 dB for a total attenuation of 6 dB. Attenuation accuracy is excellent at ± 0.2 dB typical step error with an IIP3 of +50 dBm. Two control voltage inputs, toggled between 0 and +5V, are used to select each attenuation state. A single Vdd bias of +5V is required. Electrical Specifi cations, TA = +25° C, With Vdd = +5V & Vctl = 0/+5V* Frequency (GHz) O Parameter DC - 2.5 GHz 2.5 - 6.0 GHz Insertion Loss Attenuation Range Min. Typ. Max. Units 0.5 0.8 0.8 1.2 dB dB DC - 6 GHz 6 dB DC - 2.5 GHz 2.5 - 6.0 GHz 20 15 dB dB DC - 6 GHz ± 0.2 + 2% of Atten. Setting Max. ± 0.4 + 2% of Atten. Setting Max. dB dB Input Power for 0.1 dB Compression 0.25 - 6.0 GHz 22 dBm Input Third Order Intercept Point (Two-Tone Input Power= 0 dBm Each Tone) 0.25 - 6.0 GHz 50 dBm 135 155 ns ns Return Loss (RF1 & RF2, All Atten. States) Attenuation Accuracy: (Referenced to Insertion Loss) Switching Characteristics 2 dB State 4, 6 dB States DC - 6 GHz tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) * Bypass capacitor connecting ACG1 & ACG2 to RF ground required per pin description herein. 5 - 132 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC467LP3 / 467LP3E v01.0705 2 dB LSB GaAs MMIC 2-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 6 GHz (Only Major States are Shown) 0 0 -0.5 -5 -1 -1.5 -2 +25 C +85 C -40 C -2.5 -10 -15 -20 -25 -3 -30 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 Normalized Attenuation (Only Major States are Shown) 5.5 6 Bit Error vs. Attenuation State 0 1 0.8 -2 -4 -6 SO BIT ERROR (dB) 0.6 2 dB 4 dB 6 dB -8 -10 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 0.4 0.2 0 -0.2 -0.4 80 MHz 500 MHz 1 GHz 2 GHz -0.6 -0.8 B 3 GHz 4 GHz 5 GHz 6 GHz -1 6 2 4 FREQUENCY (GHz) 6 ATTENUATION STATE (dB) Bit Error vs. Frequency Relative Phase vs. Frequency (Only Major States are Shown) (Only Major States are Shown) 20 O 1 15 RELATIVE PHASE (deg) 0.6 BIT ERROR (dB) 5 FREQUENCY (GHz) LE FREQUENCY (GHz) NORMALIZED ATTENUATION (dB) IL 2 dB 4 dB 6 dB TE RETURN LOSS (dB) INSERTION LOSS (dB) Insertion Loss ATTENUATORS - SMT 5 Return Loss RF1, RF2 0.2 -0.2 2 dB 4 dB 6 dB -0.6 10 5 0 2 dB 4 dB 6 dB -5 -1 -10 0 1 2 3 4 FREQUENCY (GHz) 5 6 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 133 HMC467LP3 / 467LP3E v01.0705 2 dB LSB GaAs MMIC 2-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 6 GHz 5 Worst Case Step Error Between Successive Attenuation States Truth Table Control Voltage Input 2 dB 4 dB 6 dB STEP ERROR (dB) 0.6 0.2 -0.2 Attenuation Setting RF1 - RF2 V1 4 dB V2 2 dB High High Reference I.L. High Low 2 dB Low High 4 dB TE ATTENUATORS - SMT 1 Low -0.6 6 dB Max. Atten. Low Any combination of the above states will provide an attenuation approximately equal to the sum of the bits selected. -1 0 1 2 3 4 FREQUENCY (GHz) 5 6 Bias Voltage & Current LE Vdd Range= +5.0 Vdc ± 10% Vdd (Vdc) Idd (Typ.) (mA) Idd (Max.) (mA) +5.0 0.7 1.2 State Bias Condition Low 0 to 0.8 Vdc @ -5 uA Typ. High +2.0 to +5.0 Vdc @ 40 uA Typ. O B SO TTL/CMOS Control Voltages 5 - 134 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC467LP3 / 467LP3E v01.0705 2 dB LSB GaAs MMIC 2-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 6 GHz -0.5 Vdc to Vdd +1 Vdc Bias Voltage (Vdd) +7.0 Vdc Staorage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C RF Input Power +30 dBm ESD Sensitivity (HBM) Class 1A TE Control Voltage (V1, V2) ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS O B SO LE Outline Drawing ATTENUATORS - SMT 5 Absolute Maximum Ratings NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC467LP3 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC467LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] 467 XXXX [2] 467 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 135 HMC467LP3 / 467LP3E v01.0705 2 dB LSB GaAs MMIC 2-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 6 GHz 5 Function Description 1, 2, 4, 9 - 12, 14, 15 N/C These pins should be connected to PCB RF ground to maximize performance. 3 Vdd Supply Voltage 5, 8 V2, V1 See truth table and control voltage table. 6, 7 ACG1, ACG2 External capacitor to ground is required. Select value for lowest frequency of operation. Place capacitor as close to pins as possible. 13, 16 RF2, RF1 These pins are DC coupled and matched to 50 Ohm. Blocking capacitors are required. GND Package bottom has an exposed metal paddle that must be connected to RF/DC ground. Interface Schematic LE TE Pin Number SO ATTENUATORS - SMT Pin Descriptions O B Application Circuit 5 - 136 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC467LP3 / 467LP3E v01.0705 2 dB LSB GaAs MMIC 2-BIT DIGITAL POSITIVE CONTROL ATTENUATOR, DC - 6 GHz TE LE B SO ATTENUATORS - SMT 5 Evaluation PCB List of Materials for Evaluation PCB 107008 Description O Item J1 - J2 PCB Mount SMA Connector J3 - J7 DC Pin C1, C2 1000 pF Capacitor, 0402 Pkg. C3 1000 pF Capacitor, 0603 Pkg. C4 3300 pF Capacitor, 0603 Pkg. U1 HMC467LP3 / HMC467LP3E Digital Attenuator PCB [2] 106980 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB [1] The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [2] Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 137