HMC468 Data Sheet PDF

Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC468LP3 / 468LP3E
v03.1107
1 dB LSB GaAs MMIC 3-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 6 GHz
ATTENUATORS - SMT
5
Typical Applications
Features
The HMC468LP3 / HMC468LP3E is ideal for:
1 dB LSB Steps to 7 dB
• Cellular; UMTS/3G Infrastructure
High IP3: +50 dBm
• Fixed Wireless & WLL
± 0.25 dB Typical Bit Error
• Microwave Radio & VSAT
Single Control Line Per Bit
Single +5V Supply
• Test Equipment
16 Lead 3x3mm SMT Package: 9mm2
Included in the HMC-DK004 Designer’s Kit
Functional Diagram
General Description
The HMC468LP3 & HMC468LP3E are broadband
3-bit GaAs IC digital attenuators in low cost leadless
surface mount packages. Covering DC to 6.0 GHz,
the insertion loss is less than 1 dB typical up to 4
GHz. The attenuator bit values are 1 (LSB), 2 and 4
dB for a total attenuation of 7 dB. Attenuation accuracy is excellent at ±0.4 dB typical step error with an
IIP3 of +50 dBm. Three control voltage inputs, toggled
between 0 and +5V, are used to select each attenuation state. A single Vdd bias of +5V is required.
Electrical Specifi cations, TA = +25° C, With Vdd = +5V & Vctl = 0/+5V
Parameter
Frequency (GHz)
Typ.
Max.
Units
DC - 2.5 GHz
2.5 - 4.5 GHz
4.5 - 6.0 GHz
0.7
0.9
1.3
1.0
1.3
1.8
dB
dB
dB
DC - 6 GHz
7
dB
DC - 4 GHz
4.0 - 6.0 GHz
20
15
dB
dB
DC - 2.5 GHz
2.5 - 6.0 GHz
2.5 - 6.0 GHz
± 0.2 + 2% of Atten. Setting Max.
± 0.3 + 3% of Atten. Setting Max.
± 0.4 + 4% of Atten. Setting Max.
dB
dB
dB
Input Power for 0.1 dB Compression
0.25 - 6.0 GHz
20
dBm
Input Third Order Intercept Point
(Two-Tone Input Power= 0 dBm Each Tone)
0.25 - 6.0 GHz
50
dBm
110
135
ns
ns
Insertion Loss
Attenuation Range
Return Loss (RF1 & RF2, All Atten. States)
Attenuation Accuracy:
(Referenced to Insertion Loss)
Switching Characteristics
All States
1 - 4 dB States
5 - 7 dB States
Min.
DC - 6 GHz
tRISE, tFALL (10/90% RF)
tON, tOFF (50% CTL to 10/90% RF)
* Bypass capacitor connecting ACG1, ACG2 & ACG3 to RF ground required per pin description herein.
5 - 138
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC468LP3 / 468LP3E
v03.1107
1 dB LSB GaAs MMIC 3-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 6 GHz
(Only Major States are Shown)
0
-0.5
-5
RETURN LOSS (dB)
INSERTION LOSS (dB)
0
-1
-1.5
+25 C
+85 C
-40 C
-2
-2.5
IL
1 dB
2 dB
4 dB
7 dB
-10
-15
-20
-25
-30
-3
-35
0
1
2
3
4
5
0
6
1
FREQUENCY (GHz)
2
3
4
5
6
FREQUENCY (GHz)
Normalized Attenuation
Bit Error vs. Attenuation State
0
1
-2
0.6
BIT ERROR (dB)
NORMALIZED ATTENUATION (dB)
(Only Major States are Shown)
-4
-6
-8
1 dB
2 dB
0.2
-0.2
80 MHz
500 MHz
1 GHz
2 GHz
-0.6
4 dB
7 dB
-10
3 GHz
4 GHz
5 GHz
6 GHz
-1
0
1
2
3
4
5
6
1
2
FREQUENCY (GHz)
3
4
5
6
7
5
6
ATTENUATION STATE (dB)
Bit Error vs. Frequency
Relative Phase vs. Frequency
(Only Major States are Shown)
(Only Major States are Shown)
1
20
15
RELATIVE PHASE (deg)
0.6
BIT ERROR (dB)
ATTENUATORS - SMT
5
Return Loss RF1, RF2
Insertion Loss
0.2
-0.2
1 dB
2 dB
4 dB
7 dB
-0.6
1 dB
2 dB
4 dB
7 dB
10
5
0
-5
-1
-10
0
1
2
3
4
FREQUENCY (GHz)
5
6
0
1
2
3
4
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 139
HMC468LP3 / 468LP3E
v03.1107
1 dB LSB GaAs MMIC 3-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 6 GHz
5
Worst Case Step Error
Between Successive Attenuation States
Truth Table
Control Voltage Input
0.6
STEP ERROR (dB)
ATTENUATORS - SMT
1
0.2
-0.2
-0.6
Attenuation Setting
RF1 - RF2
V1
4 dB
V2
2 dB
V3
1 dB
High
High
High
High
High
Low
1 dB
High
Low
High
2 dB
Low
High
High
4 dB
Low
Low
Low
7 dB
Reference I.L.
Any combination of the above states will provide an attenuation
approximately equal to the sum of the bits selected.
-1
0
1
2
3
4
5
6
FREQUENCY (GHz)
Bias Voltage & Current
Vdd Range= +5.0 Vdc ± 10%
Vdd
(Vdc)
Idd (Typ.)
(mA)
Idd (Max.)
(mA)
+5.0
1.05
1.8
TTL/CMOS Control Voltages
5 - 140
State
Bias Condition
Low
0 to 0.8 Vdc @ -5 uA Typ.
High
+2.0 to +5.0 Vdc @ 40 uA Typ.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC468LP3 / 468LP3E
v03.1107
1 dB LSB GaAs MMIC 3-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 6 GHz
Control Voltage (V1 to V3)
-0.5 Vdc to Vdd +1 Vdc
Bias Voltage (Vdd)
+7 Vdc
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
RF Input Power
+30 dBm
ESD Sensitivity (HBM)
Class 1A
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
ATTENUATORS - SMT
5
Absolute Maximum Ratings
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC468LP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC468LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
468
XXXX
[2]
468
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 141
HMC468LP3 / 468LP3E
v03.1107
1 dB LSB GaAs MMIC 3-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 6 GHz
ATTENUATORS - SMT
5
Pin Descriptions
Pin Number
Function
Description
1, 3, 4, 8,
9, 10, 12
N/C
These pins should be connected to PCB
RF ground to maximize performance.
2, 11
RF1, RF2
This pin is DC coupled and matched to 50 Ohm.
Blocking capacitors are required
13 - 15
V1 - V3
See truth table and control voltage table.
5-7
ACG1 - ACG3
External capacitor to ground is required.
Select value for lowest frequency of operation.
Place capacitor as close to pins as possible.
16
Vdd
Supply Voltage
GND
Package bottom has an exposed metal paddle
that must be connected to RF/DC ground.
Interface Schematic
Application Circuit
5 - 142
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC468LP3 / 468LP3E
v03.1107
1 dB LSB GaAs MMIC 3-BIT DIGITAL
POSITIVE CONTROL ATTENUATOR, DC - 6 GHz
5
ATTENUATORS - SMT
Evaluation PCB
List of Materials for Evaluation PCB 107302 [1]
Item
Description
J1 - J2
PCB Mount SMA Connector
J3 - J7
DC Pin
C1
1000 pF Capacitor, 0603 Pkg.
C2, C3
100 pF Capacitor, 0402 Pkg.
C4
3300 pF Capacitor, 0603 Pkg.
U1
HMC468LP3 / HMC468LP3E
Digital Attenuator
PCB [2]
107300 Evaluation PCB
The circuit board used in the final application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and exposed paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 143