TE Analog Devices Welcomes Hittite Microwave Corporation O B SO LE NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com TE O B SO LE THIS PAGE INTENTIONALLY LEFT BLANK HMC665LP4 / 665LP4E v00.0508 Features The HMC665LP4 / HMC665LP4E is ideal for: High Input IP3: +23 dBm • Cellular/3G & WiMAX/LTE/4G Infrastructure Low Input LO Drive: -3 to +6 dBm • Base Stations & Repeaters High LO to RF Isolation: 36 dB • Broadband & Fixed Wireless High Conversion Gain: 10 dB • Access Points Ideal for Upconversion or Downconversion • Test & Measurement Equipment 24 Lead 4x4mm SMT Package: 16mm2 Functional Diagram General Description TE Typical Applications LE The HMC665LP4E is a highly integrated converter IC that operates from 0.7 to 1.2 GHz for both up-conversion and downconversion applications. The HMC665LP4E incorporates a high dynamic range, passive doublebalanced mixer core with integrated LO and IF amplifiers, making it ideal for compact transceiver applications in GSM, WCDMA, TD-SCDMA, WiBro and WiMAX. This versatile converter RFIC operates with a low LO input power level of only -3 dBm, provides up to 10 dB conversion gain, and exhibits +23 dBm Input IP3 in downconversion mode. This RFIC provides up to 11 dB conversion gain in upconverter mode. Specific evaluation boards are available for both upconverter and downconverter modes. B SO Mixers - HIGH IP3 - SMT 10 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz O Electrical Specifications, TA = +25° C, LO = 0 dBm, VccLO= VddIF = +5V Parameter Min. Frequency Range, RF, LO Frequency Range, IF Conversion Gain 7 Noise Figure (SSB) LO to RF Isolation 32 Typ. Max. Units 0.7 - 1.2 GHz 250 - 450 MHz 10 dB 10 dB 36 dB LO to IF Isolation 1 dB IP3 (Input) 23 dBm 1 dB Compression (Input) 10 dBm LO Drive Input Level (Typical) -3 to +6 Supply Current (IddIF + IccLO) 150 dBm 200 mA *Unless otherwise noted, all measurements performed as a downconverter and configured as shown in the downconverter mode application circuit, IF=250 MHz 10 - 1 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Downconversion Plots Conversion Gain vs. LO Drive, IF = 450 MHz 10 10 5 0 -5 700 900 1100 1300 +25C +85C -40C 700 900 1100 1300 1500 5 0 -5 +25C +85C -40C -10 -15 -20 500 1500 O Input IP2 vs. LO Drive, IF = 450 MHz 700 90 80 80 70 70 60 700 900 RF FREQUENCY (MHz) 60 50 -3 dBm 0 dBm +3 dBm +6 dBm 40 1100 Input IP2 vs. Temperature, IF = 450 MHz 90 50 900 FREQUENCY (MHz) IP2 (dBm) IP2 (dBm) 1300 10 FREQUENCY (MHz) 30 500 1500 LE B SO CONVERSION GAIN (dB) -20 500 1300 15 10 -15 1100 20 15 -10 900 Conversion Gain vs. Temperature, IF = 450 MHz 20 -5 700 FREQUENCY (MHz) Conversion Gain vs. Temperature, IF = 250 MHz 0 -5 -15 500 1500 FREQUENCY (MHz) 5 LO= -3 dBm LO= 0 dBm LO= 3 dBm LO= 6 dBm -10 -10 -15 500 0 TE LO= -3 dBm LO= 0 dBm LO= 3 dBm LO= 6 dBm 10 5 Mixers - HIGH IP3 - SMT 15 CONVERSION GAIN (dB) 15 CONVERSION GAIN (dB) CONVERSION GAIN (dB) Conversion Gain vs. LO Drive, IF = 250 MHz +25C +85C -40C 40 1100 1300 30 500 700 900 1100 1300 RF FREQUENCY (MHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 - 2 HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Downconversion Plots Input IP3 vs. Temperature, IF = 450 MHz 30 25 25 20 20 IP3 (dBm) 30 15 -3 dBm 0 dBm +3 dBm +6 dBm 5 700 900 1100 0 500 1300 900 1100 1300 Isolation vs. Frequency LE Input P1dB vs. Temperature, IF = 350 MHz 10 16 B SO 10 +25C +85C -40C 700 900 1100 ISOLATION (dB) 0 13 4 500 700 RF FREQUENCY (MHz) RF FREQUENCY (MHz) 7 +25C +85C -40C 10 5 0 500 15 TE 10 P1dB (dBm) Mixers - HIGH IP3 - SMT 10 IP3 (dBm) Input IP3 vs. LO Drive, IF = 450 MHz -10 RF to IF LO to RF LO to IF -20 -30 -40 500 1300 700 900 1100 1300 1500 1700 FREQUENCY (MHz) RF FREQUENCY (MHz) Upconversion Plots Conversion Gain vs. LO Drive, IF = 450 MHz 15 15 10 10 CONVERSION GAIN (dB) CONVERSION GAIN (dB) O Conversion Gain vs. LO Drive, IF = 250 MHz 5 0 LO= -3 dBm LO= 0 dBm LO= 3 dBm LO= 6 dBm -5 825 1000 FREQUENCY (MHz) 10 - 3 0 LO= -3 dBm LO= 0 dBm LO= 3 dBm LO= 6 dBm -5 -10 -10 -15 650 5 1175 1350 -15 650 825 1000 1175 1350 FREQUENCY (MHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Input IP3 vs. LO Drive, IF = 450 MHz 20 80 15 10 70 60 50 LO = -3 dBm LO = 0 dBm LO = 3 dBm LO = 6 dBm 30 650 800 950 -5 1100 -15 650 1250 LE -15 Conversion Gain Return Loss B SO -20 RETURN LOSS (dB) -5 -10 300 400 500 600 -10 -15 -20 RF LO -25 -30 0 0.5 MxN Spurious @ IF Port 1 2 4 2.5 3 nLO Spur at RF Port 0 1 2 3 4 LO Freq. (GHz) 1 2 3 4 xx 3 21 29 58 0.5 31 32 32 39 7 0 33 52 59 0.6 28 23 32 47 66 56 50 65 84 0.7 30 21 30 44 91 84 73 77 91 0.8 37 21 32 47 91 91 91 91 91 0.9 38 23 37 53 1.0 35 24 40 43 1.2 34 27 33 55 1.4 35 32 33 58 1.6 36 38 46 62.6 O 3 2 Harmonics of LO nLO 1 1.5 FREQUENCY (MHz) IF FREQUENCY (MHz) 0 1250 -5 0 mRF 1100 0 5 RESPONSE (dB) 950 Return Loss 10 -35 200 800 RF FREQUENCY (MHz) IF Bandwidth -30 -3 dBm 0 dBm +3 dBm +6 dBm -10 RF FREQUENCY (MHz) -25 0 TE 40 10 5 All values in dBc below IF power level (1RF - 1LO) Absolute Maximum Ratings RF / MIX IF Input (VddIF = +5V) +22 dBm LO Input (VccLO = +5V) +10 dBm IFIN +15 dBm VccLO +7 Vdc VddIF +8 Vdc Junction Temperature 150 °C Continuous Pdiss (T = 85°C) (derate 14.9 mW/°C above 85°C) 0.97 W Thermal Resistance (junction to ground paddle) Storage Temperature Operating Temperature Mixers - HIGH IP3 - SMT 90 IP3 (dBm) IP2 (dBm) Input IP2 vs. LO Drive, IF = 450 MHz LO = 0 dBm Values in dBc below input LO level measured at RF port. Typical Supply Current VddIF + VccLO IddIF + IccLO 67.2 °C/W +4.5 130 mA -65 to +150°C +5.0 150 mA -40 to +85°C +5.5 165 mA For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 - 4 HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Typical Performance Cascade Analysis HMC665LP4E Downconverter Mode (RF Input = 700 to 1200 MHz, IF Output = 250 to 450 MHz, LO = Low Side or High Side) Component Level NF (dB) OIP3 (dBm) Mixer w/ LO Amplifier -8.0 8.5 15.0 7.0 IF Amplifier 18.0 1.0 37.5 21.0 150.0 Description 10 HMC665LP4E OP1dB (dBm) Cumulative MCM Performance Gain (dB) Cumulative MCM Performance +5V Current (mA) Gain (dB) NF (dB) OIP3 (dBm) IIP3 (dBm) OP1dB (dBm) 57.0 -8.0 8.5 15.0 23.0 7.0 16.0 93.0 10.0 9.4 31.7 21.7 19.5 10.5 10.0 9.4 31.7 21.7 19.5 10.5 IP1dB (dBm) TE Typical Performance Cascade Analysis HMC665LP4E Upconverter Mode (RF Output = 700 to 1200 MHz, IF Input = 250 to 450 MHz, LO = Low Side or High Side) Component Level IF Amplifier 18.0 1.0 38 Mixer w/ LO Amplifier -7.5 8.5 21 HMC665LP4E Cumulative MCM Performance NF (dB) OIP3 (dBm) OP1dB (dBm) +5V Current (mA) Gain (dB) 21.0 93.0 18.0 NF (dB) 7.0 1.0 Cumulative MCM Performance OIP3 (dBm) IIP3 (dBm) OP1dB (dBm) IP1dB (dBm) 38 20 21.0 4.0 57.0 10.0 1.3 20.5 10 7.0 -3.0 150.0 10.0 1.3 20.5 10 7.0 -3.0 LE Description Gain (dB) * IF image rejection filter is not included in the released eval boards. B SO Outline Drawing ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS O Mixers - HIGH IP3 - SMT * RF image rejection filter is not included in the released eval boards. NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. 10 - 5 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Package Information Package Body Material Lead Finish MSL Rating HMC665LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC665LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] H665 XXXX H665 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX TE Pin Descriptions Function 3 RF This pin is DC coupled and matched to 50 Ohms. 7 IFIN This pin is matched to 50 Ohms with a 56nH inductor to ground. See Application Circuit. 9 CAP AC ground. An external capacitor of 0.01 µF to ground is required for low frequency bypassing. See application circuit for further details. Interface Schematic B SO N/C Description No connection. These pins may be connected to RF ground. Performance will not be affected. LE Pin Number 1, 2, 4, 5, 6, 8, 11, 14, 15, 19, 20, 22 - 24 MIXIF 12 IFOUT This pin is AC coupled and matched to 50 Ohms. 13 VddIF Power supply for IF amplifier. Choke inductor and bypass capacitor are required. See application circuit. O 10 This pin is DC coupled. For applications not requiring operation to DC, this port should be DC blocked externally using a series capacitor whose value has been chosen to pass the necessary IF frequency range. For operation to DC, this pin must not source/sink more than 18 mA of current or part non-function and possible part failure will result. 16 MIXLO This pin is DC coupled and matched to 50 Ohms. An off chip DC blocking capacitor is required. 17 GND Backside of package has exposed metal ground paddle that must also be connected to ground. 18 VccLO Power supply and RF Output of the LO amplifier. Three external bypass capacitors are recommended for optimum performance, as illustrated in the application circuit. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 Mixers - HIGH IP3 - SMT Part Number 10 - 6 HMC665LP4 / 665LP4E v00.0508 Pin Descriptions (Continued) Pin Number Function Description 21 LO This pin is DC coupled and matched to 50 Ohms. An off chip DC blocking capacitor is required. See application circuit. 10 Interface Schematic LE TE Evaluation PCB - Upconverter Mode B SO Mixers - HIGH IP3 - SMT GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz O List of Materials for Evaluation PCB 122009 [1] Item Description J1 - J3 PCB Mount SMA RF Connector J4 2mm DC Header C1, C2, C3 100 pF Chip Capacitor, 0402 Pkg. C4, C6 1000 pF Chip Capacitor, 0603 Pkg. C5, C7 2.2 µF Capacitor, Tantalum C8 0.01 µF Chip Capacitor, 0402 Pkg. L1, L2 56 nH Chip Inductor, 0402 Pkg. L3 36 nH Chip Inductor, 0603 Pkg. R1, R3, R4 0 Ohm Resistor, 0402 Pkg. R5 24 Ohm Resistor, 1210 Pkg. U1 HMC665LP4(E) - Mixer PCB [2] 119242 Evaluation Board The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR 10 - 7 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Evaluation PCB - Downconverter Mode Mixers - HIGH IP3 - SMT B SO LE TE 10 List of Materials for Evaluation PCB 122010 [1] Item PCB Mount SMA RF Connector O J1 - J3 Description J4 2mm DC Header C1, C2, C3 100 pF Chip Capacitor, 0402 Pkg. C4, C6 1000 pF Chip Capacitor, 0603 Pkg. C5, C7 2.2 µF Capacitor, Tantalum C8 0.01 µF Chip Capacitor, 0402 Pkg. L1, L2 56 nH Chip Inductor, 0402 Pkg. L3 36 nH Chip Inductor, 0603 Pkg. R2, R3, R4 0 Ohm Resistor, 0402 Pkg. R5 24 Ohm Resistor, 1210 Pkg. U1 HMC665LP4(E) - Mixer PCB [2] 119242 Evaluation Board The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 - 8 HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Application Circuit - Upconverter Mode TE LE B SO O Mixers - HIGH IP3 - SMT 10 10 - 9 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC665LP4 / 665LP4E v00.0508 GaAs MMIC MIXER w/ INTEGRATED IF & LO AMPLIFIER, 0.7 - 1.2 GHz Application Circuit - Downconverter Mode Mixers - HIGH IP3 - SMT O B SO LE TE 10 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 - 10