PDF Data Sheet

Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC441LP3 / 441LP3E
v05.0812
LINEAR & POWER AMPLIFIERS - SMT
GaAs pHEMT MMIC MEDIUM
POWER AMPLIFIER, 6.5 - 13.5 GHz
Typical Applications
Features
The HMC441LP3 / HMC441LP3E is a medium PA for:
Gain: 14 dB
• Point-to-Point Radios
Saturated Power: +20 dBm @ 20% PAE
• Point-to-Multi-Point Radios
Single Supply Voltage:
+5V w/ Optional Gate Bias
• VSAT
50 Ohm Matched Input/Output
• LO Driver for HMC Mixers
16 Lead 3x3mm SMT Package: 9mm2
• Military EW & ECM
Functional Diagram
General Description
The HMC441LP3 & HMC441LP3E are broadband
GaAs PHEMT MMIC Medium Power Amplifiers which
operate between 6.5 and 13.5 GHz. The leadless
plastic QFN surface mount packaged amplifier
provides 14 dB of gain, +20 dBm saturated power
at 20% PAE from a +5V supply voltage. An optional
gate bias is provided to allow adjustment of gain,
RF output power, and DC power dissipation. This
50 Ohm matched amplifier does not require any
external components making it an ideal linear gain
block or driver for HMC SMT mixers.
Vgg1, Vgg2: Optional Gate Bias
Electrical Specifications, TA = +25° C, Vdd = 5V, Vgg1 = Vgg2 = Open
Parameter
Min.
Frequency Range
Gain
10
Gain Variation Over Temperature
12
0.025
15
18
26
29
5.0
90
10
0.025
14
26
dB
0.025
dB/ °C
dB
13
dB
17
dBm
19.5
dBm
29
dBm
4.75
115
Units
GHz
14
4.5
90
Max.
13
0.02
20
115
Typ.
11.0 - 13.5
15
26
Supply Current (Idd)
Min.
15
16
Noise Figure
Max.
14
0.02
18.5
23
Typ.
8.0 - 11.0
12
13
Saturated Output Power (Psat)
1
Min.
12
Output Return Loss
Output Third Order Intercept (IP3)
Max.
13
0.02
Input Return Loss
Output Power for 1 dB Compression (P1dB)
Typ.
6.5 - 8.0
90
dB
115
mA
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC441LP3 / 441LP3E
v05.0812
GaAs pHEMT MMIC MEDIUM
POWER AMPLIFIER, 6.5 - 13.5 GHz
Broadband Gain & Return Loss
Gain vs. Temperature
15
16
5
S21
S11
S22
0
GAIN (dB)
RESPONSE (dB)
10
-5
12
+25 C
+85 C
-40 C
8
-10
-15
4
-20
-25
0
4
5
6
7
8
9
10
11
12
13
14
15
6
16
7
8
FREQUENCY (GHz)
Input Return Loss vs. Temperature
11
12
13
14
0
+25 C
+85 C
-40 C
+25 C
+85 C
-40 C
-5
RETURN LOSS (dB)
-5
RETURN LOSS (dB)
10
Output Return Loss vs. Temperature
0
-10
-15
-20
-10
-15
-20
-25
-25
6
7
8
9
10
11
12
13
14
6
7
8
FREQUENCY (GHz)
9
10
11
12
13
14
12
13
14
FREQUENCY (GHz)
P1dB vs. Temperature
Psat vs. Temperature
24
24
20
20
16
16
Psat (dB)
P1dB (dB)
9
FREQUENCY (GHz)
LINEAR & POWER AMPLIFIERS - SMT
20
20
12
+25 C
+85 C
8
+25 C
+85 C
-40 C
12
8
-40 C
4
4
6
7
8
9
10
11
FREQUENCY (GHz)
12
13
14
6
7
8
9
10
11
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
2
HMC441LP3 / 441LP3E
v05.0812
GaAs pHEMT MMIC MEDIUM
POWER AMPLIFIER, 6.5 - 13.5 GHz
Power Compression @ 10 GHz
Output IP3 vs. Temperature
36
Pout
Gain
PAE
18
32
16
14
IP3 (dBm)
Pout (dBm), GAIN (dB), PAE (%)
20
12
10
8
28
24
6
+25 C
+85 C
-40 C
20
4
2
0
-10
16
-6
-2
2
6
6
10
7
8
12
13
14
210
35
32
30
GAIN (dB), P1dB (dBm), Psat (dBm)
GAIN (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
11
Gain, Power & Idd
vs. Gate Voltage @ 10 GHz
Gain, Power & Output IP3
vs. Supply Voltage @ 10 GHz
28
26
Gain
P1dB
Psat
IP3
24
22
20
18
16
14
12
30
Gain
P1dB
Psat
25
180
Idd
150
20
120
15
90
10
60
5
30
0
0
10
3
3.5
4
4.5
5
5.5
-2
-1.8
-1.6
-1.4
-1.2
-1
-0.8
-0.6
-0.4
-0.2
0
Vgg1, Vgg2 Gate Volltage (V)
Reverse Isolation vs. Temperature
Noise Figure vs. Temperature
10
0
+25 C
+85 C
-40 C
-10
ISOLATION (dB)
8
NOISE FIGURE (dB)
10
FREQUENCY (GHz)
Vdd Supply Voltage (V)
6
4
2
+25 C
+85 C
-40 C
-20
-30
-40
0
-50
6
7
8
9
10
11
FREQUENCY (GHz)
3
9
INPUT POWER (dBm)
12
13
14
6
7
8
9
10
11
12
13
14
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
Idd (mA)
LINEAR & POWER AMPLIFIERS - SMT
22
HMC441LP3 / 441LP3E
v05.0812
GaAs pHEMT MMIC MEDIUM
POWER AMPLIFIER, 6.5 - 13.5 GHz
Absolute Maximum Ratings
+6 Vdc
Gate Bias Voltage (Vgg1,Vgg2)
-8 to 0 Vdc
RF Input Power (RFIN)(Vdd = +5 Vdc)
Channel Temperature
Vdd (V)
Idd (mA)
+5.5
92
+15 dBm
+5.0
90
175 °C
+4.5
88
+3.3
83
+3.0
82
Continuous Pdiss (T = 85 °C)
(derate 8.5 mW/°C above 85 °C)
0.76 W
Thermal Resistance
(channel to ground paddle)
118.2 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
Note: Amplifier will operate over full voltage range shown above
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
LINEAR & POWER AMPLIFIERS - SMT
Drain Bias Voltage (Vdd)
Typical Supply Current vs. Vdd
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC441LP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC441LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
441
XXXX
441
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
4
HMC441LP3 / 441LP3E
v05.0812
GaAs pHEMT MMIC MEDIUM
POWER AMPLIFIER, 6.5 - 13.5 GHz
LINEAR & POWER AMPLIFIERS - SMT
Pin Descriptions
5
Pin Number
Function
Description
1, 3-5, 8-10,
12-14, 16
N/C
This pin may be connected to RF/DC ground.
2
RFIN
This pin is AC coupled
and matched to 50 Ohms.
6, 7
Vgg1, Vgg2
Optional gate control for amplifier. If left open, the amplifier
will run at standard current. Negative voltage applied will
reduce current.
11
RFOUT
This pin is AC coupled
and matched to 50 Ohms.
15
Vdd
Power Supply Voltage for the amplifier. An external bypass
capacitor of 100 pF is required.
GND
Package bottom must be connected to RF/DC ground.
Interface Schematic
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC441LP3 / 441LP3E
v05.0812
GaAs pHEMT MMIC MEDIUM
POWER AMPLIFIER, 6.5 - 13.5 GHz
LINEAR & POWER AMPLIFIERS - SMT
Evaluation PCB
List of Materials for Evaluation PCB 106705 [1]
Item
Description
J1 - J2
PCB Mount SMA Connector
J3 - J7
DC Pin
C1
4.7 µF Capacitor, Tantalum
C2 - C4
100 pF Capacitor, 0402 Pkg.
U1
HMC441LP3 / HMC441LP3E Amplifier
PCB [2]
106639 Evaluation PCB, 10 mils
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
The circuit board used in the final application
should use RF circuit design techniques. Signal
lines should have 50 Ohm impedance while the
package ground leads and exposed paddle should
be connected directly to the ground plane similar to
that shown. A sufficient number of via holes should
be used to connect the top and bottom ground
planes. The evaluation board should be mounted
to an appropriate heat sink. The evaluation circuit
board shown is available from Hittite upon request.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
6