EURO QUARTZ HDK3261 DIFFERENTIAL LVDS OSCILLATORS 13.50MHz to 200.0MHz 3.2 x 2.5 x 1.0mm 6 pad SMD DESCRIPTION Femtosecond integrated phase jitter (200fs typical) Superior phase noise (-144dBc/Hz at 100kHz) High performance and low price Supply voltage 2.5 or 3.3 Volts OUTLINE & DIMENSIONS SPECIFICATION Frequency Range: Output Logic Phase Noise: Frequency Stability: Operating Temp Range Commercial: Industrial: Input Voltage: Output Voltage High '1': Low '0': Integrated Phase Noise: 13.5MHz to 200.0MHz Differential LVDS square wave Output Swing: Load: 350mV minimum (Vdd = 2.5V) 50Ω into Vcc-2V Rise/Fall Times: 0.3ns typical, 0.5ns typical. Duty Cycle: Current Consumption: Enable/Disable (Pad 1) Enable: 50±10% 30mA typical, 50mA maximum -10° to +70°C -40° to +85°C +2.5V±5% or +3.3VDC±5% 1.43V typ., 1.6V max., (RL = 100Ω) 0.9V min., 1.1V typ., (RL = 101Ω) 0.2ps typical, 0.5ps maximum No connection or min. 70% Vdd is applied to pad 1. 30% Vdd max. applied to pad 1. Output: internal pull-up. Oscillation enable time is 2ms max. 10ms max. ±3ppm per year max., ±2ppm thereafter. At T amb +25°C Disable: Start-up Time: Ageing: ABSOLUTE MAXIMUM RATINGS ( Supply Voltage: Vss -0.5V min., 5.0V max. Input Voltage: Vss -0.5V min., Vdd +0.5V max. Input Voltage: Vss -0.5V min., Vdd +0.5V max. ENVIRONMENTAL PERFORMANCE SPECIFICATION 'Green' Requirements: ) MSL Level: Storage Temperature Range: Humidity: Hermetic Seal: Solderability: Reflow: Vibration: Shock: TYPICAL PHASE NOISE (156.250MHz) Offset 10Hz 100Hz 1kHz 10kHz 100kHz 1MHz 10MHz ESD Protection: Contact pad surface finish: dBc/Hz -75 -120 -135 Weight per unit: -90 -142 25 50 100 25 50 100 Temperature Range Order Code °C -10 to +70 -10 to +70 -10 to +70 -40 to +85 -40 to +85 -40 to +85 -155 PART NUMBERS STABILITY OVER TEMPERATURE RANGE Stability ±ppm -147 RoHS 6/6 (2002-95/EC) and WEEE (2002/96/EC) Compliant Level 1 per IPC/JEDEC J-STD-020D.1 -55°C to +125°C 85% RH, 85°, 48 hours Leak rate 2*10-8 Atm-cm3/sec. max. MIL-STD-202F Method 208E 260°C for 10sec. max., 2 times max. MIL-STD-202F Method 204, 35g 50 to 2000Hz MIL-STD-202F Method 213B test condition E, 1000g, ½ sine 2kV max. Human body model Gold (Au) (0.3~1.0µm) on Nickel (N) (1.27~8.89µm) 160mg typical A B C D E F HDK5361 oscillator part numbers are derived as follows: Example: 25HDK5361-A-156.250 25 HDK5361 - A - 156.250 Supply Voltage 25 = 2.5VDC 3 = 3.3VDC Series Designation Temperature Stability Code A~F (See table) Frequency EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 [email protected] www.euroquartz.co.uk