Data Sheet

EURO QUARTZ
HPK5761 PECL OSCILLATORS
13.50MHz to 200.0MHz
7 x 5 x 1.8mm 6 pad SMD
DESCRIPTION
Femtosecond integrated phase jitter (200fs typical)
Ultra-low phase noise -138dBc/Hz at 10kHz
High performance with surprisingly low price
Supply voltage 2.5 or 3.3 Volts
OUTLINE & DIMENSIONS
SPECIFICATION
Frequency Range:
Output Logic
Phase Noise:
Frequency Stability:
Operating Temp Range
Commercial:
Industrial:
Input Voltage:
Output Voltage
HIGH '1':
LOW '0':
Output Swing:
Load:
Rise/Fall Times:
Duty Cycle:
Current Consumption:
Start-up Time:
Integrated Phase Jitter:
Ageing:
Packaging:
13.5MHz to 200.0MHz
Differential LVPECL square wave
-10° to +70°C
-40° to +85°C
+2.5V ±5% or +3.3VDC ±5%
Vcc -1.025V min., Vcc -0.95V typ.,
Vcc -0.88V max., 50Ω to Vdd-2V.
Vcc -1.810V min., Vcc -1.70V typ.,
Vcc -1.621V max., 50Ω to Vdd -2V.
(RL = 50Ω to Vcc -2.0V)
400mV minimum (VDD = +3.3V)
200mV minimum (VDD = +2.5V)
50Ω into Vcc-2V or Thevenin
equivalent. Terminating resistors
required on all outputs.
0.3ns typical, 0.5ns maximum.
(from 20% Vdd to 80% Vdd)
50±5% (measured at 50% waveform)
30mA typical, 50mA maximum
3ms typ., 10ms max.
0.2ps typical; 0.5ps maximum
for 156.250MHz (12kHz to 20MHz)
±3ppm per year max., ±2ppm
thereafter. At T amb +25°C
16mm tape, 8.0mm pitch. 180mm
dia. reel, 1000 pieces per reel.
Note: HPK5761 shown above; HPK5762 has Pad 2 = Enable/Disable
and Pad 1 No Connection.
ENABLE/DISABLE (TRISTATE) FUNCTION
The Enable/Disable function may be on Pad 1 or Pad 2
STABILITY OVER TEMPERATURE RANGE*
HPK5761 = Enable/Disable control on Pad 1
HPK5762 = Enable/Disable control on Pad 2
Stability
±ppm
25
50
100
25
50
100
NO
Differential and Complimentary outputs enabled.
CONNECTION
DISABLE
ENABLE
Both outputs are disabled (high impedance) when
Control Pad is taken below 0.45*Vcc referenced to
Ground (threshold). Oscillator is always ON. Only
the buffer stage is disabled.
Both outputs are enabled when Control Pad is
taken above 0.45*Vcc referenced to Ground
(threshold). Enable time 10ns +1 period of output
frequency maximum.
Temperature Range Order Code
°C
-10 to +70
-10 to +70
-10 to +70
-40 to +85
-40 to +85
-40 to +85
A
B
C
D
E
F
* Custom frequency stability is available; e.g. for +/-20 ppm over
-10 to +60°C use 'C' for custom, I.e. C20.
ABSOLUTE MAXIMUM RATINGS
(
TYPICAL PHASE NOISE (125.0MHz)
Offset
10Hz 100Hz
1kHz
10kHz 100kHz 1MHz 10MHz
dBc/Hz
-70
-128
-140
-105
-145
-147
-152
Supply Voltage:
Input Voltage:
Input Voltage:
)
Vss -0.5V min., 5.0V max.
Vss -0.5V min., Vcc +0.5V max.
Vss -0.5V min., Vcc +0.5V max.
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 [email protected] www.euroquartz.co.uk
EURO QUARTZ
HPK5761 PECL OSCILLATORS
13.50MHz to 200.0MHz
7 x 5 x 1.8mm 6 pad SMD
ENVIRONMENTAL PERFORMANCE SPECIFICATION
MSL Level:
Storage Temperature Range:
Humidity:
Hermetic Seal:
Solderability:
Reflow:
Vibration:
Shock:
ESD Protection:
Contact pad surface finish:
Weight per unit:
Level 1 per IPC/JEDEC J-STD-020D.1
-55°C to +125°C
85% RH, 85°, 48 hours
Leak rate 2*10-8 Atm-cm3/sec. max.
MIL-STD-202F Method 208E
260°C for 10sec. max., 2 times max.
MIL-STD-202F Method 204, 35g
50 to 2000Hz
MIL-STD-202F Method 213B
test condition E, 1000g, ½ sine
2kV max. Human body model
Gold (Au) (0.3~1.0µm) on Nickel (N)
(1.27~8.89µm)
180mg typical
PART NUMBERS
HPK5761 oscillator part numbers are derived as follows:
Example:
25HPK5761-A-155.520
25 HPK5761 - A - 155.520
Supply Voltage
25 = 2.5VDC
3 = 3.3VDC
Series Designation
Enable/Disable on Pad 1 = HPK5761
Enable/Disable on Pad 2 = HPK5762
Temperature Stability Code
A~F (See table)
Frequency
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 [email protected] www.euroquartz.co.uk