Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC550 / 550E v01.1010 Typical Applications Features The HMC550 / HMC550E is ideal for: Failsafe Operation - “On” When Unpowered • RFID & Electronic Toll Collection (ETC) Wide Vdd Range: 1.2V to 5V • Tags, Handsets & Portables Very Low On State Current: 200 nA • ISM, WLAN, WiMAX & WiBro Low Insertion Loss: 0.7 dB • Automotive Telematics High IP3: +52 dBm • Test Equipment Compact SOT26 SMT Package Functional Diagram General Description The HMC550 and HMC550E are low-cost SPST Failsafe switches in 6-lead SOT26 plastic packages for use in switching applications which require low insertion loss and very low current consumption. With 0.7 dB typical loss, these devices can control signals from DC to 6 GHz and are especially suited for IF and RF applications including RFID, ISM, automotive and battery powered tags and portables. RF1 and RF2 are reflective opens when “Off”. The switch requires a minimal amount of DC current in the “On” state, and offers compatibility with CMOS and some TTL logic families. The failsafe topology results in the switch being normally “On”, i.e. low insertion loss from RF1 to RF2, when no DC bias is applied. 14 Switches - SPST - SMT GaAs MMIC SPST FAILSAFE SWITCH, DC - 6 GHz Electrical Specifications TA = +25° C, Vdd = +3.3 Vdc, Vctl = 0/+3.3 Vdc (Unless Otherwise Stated), 50 Ohm System Parameter Frequency Insertion Loss DC - 6.0 GHz Isolation DC - 2.0 GHz DC - 6.0 GHz Return Loss Min. 15 8 DC - 6.0 GHz Input Power for 0.1 dB Compression Vctl = 0/+3.3V 0.5 - 6.0 GHz Input Third Order Intercept (Two-tone Input Power = +17 dBm Each Tone) Vctl = 0/+3.3V 0.5 - 6.0 GHz Switching Characteristics 23 Typ. Max. Units 0.7 0.9 dB 25 12 dB dB 20 dB 27 dBm 52 dBm 40 50 ns ns DC - 6.0 GHz tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) TA = +25° C, Vctl & Vdd Unpowered 14 - 1 Insertion Loss DC - 6.0 GHz 0.7 Return Loss DC - 6.0 GHz 20 dB Input Power for 0.1 dB Compression 0.5 - 6.0 GHz 27 dBm Input Third Order Intercept (Two-tone Input Power = +17 dBm Each Tone) 0.5 - 0.6 GHz 52 dBm 23 0.9 dB For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC550 / 550E v01.1010 GaAs MMIC SPST FAILSAFE SWITCH, DC - 6 GHz Insertion Loss Return Loss 0 -5 -0.5 RETURN LOSS (dB) -1 +25C +85C -40C -1.5 -2 +25C +85C -40C -10 -15 -20 -25 -2.5 -30 0 1 2 3 4 5 6 7 8 0 1 2 FREQUENCY (GHz) Isolation 4 5 6 7 8 14 Input IP3 vs. Temperature 0 60 -10 55 INPUT IP3 (dBm) -20 -30 -40 +25C +85C -40C -50 50 45 +25C +85C -40C 40 35 -60 -70 30 0 1 2 3 4 5 6 7 8 0 1 2 FREQUENCY (GHz) 3 4 5 6 FREQUENCY (GHz) Input P0.1dB vs. Temperature 35 30 INPUT P0.1dB (dBm) ISOLATION (dB) 3 FREQUENCY (GHz) 25 Switches - SPST - SMT INSERTION LOSS (dB) 0 20 15 +25C +85C -40C 10 5 0 0 1 2 3 4 5 6 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 14 - 2 HMC550 / 550E v01.1010 GaAs MMIC SPST FAILSAFE SWITCH, DC - 6 GHz Insertion Loss, Power Off Return Loss, Power Off 0 -5 -0.5 RETURN LOSS (dB) INSERTION LOSS (dB) 0 -1 -1.5 -2 -10 -15 -20 -25 -2.5 -30 0 1 2 3 4 5 6 7 8 0 1 2 FREQUENCY (GHz) Input P0.1dB, Power Off 4 5 6 7 8 Input IP3, Power Off 35 60 30 55 25 INPUT IP3 (dBm) INPUT P0.1dB (dBm) Switches - SPST - SMT 14 3 FREQUENCY (GHz) 20 15 10 50 45 40 35 5 0 30 0 1 2 3 4 5 6 0 1 2 FREQUENCY (GHz) 3 4 5 6 FREQUENCY (GHz) Operating Conditions Vdd & Vctl = 0 Vdc to +5 Vdc; Vctl_max = Vdd + 0.2 Vdc; Idd & Ictl = 0.1 µA, Typical Conditions Vdd - Vctl ≥ + 1.2 Vdc -0.2 Vdc < Vdd - Vctl < +0.4 Vdc RF1 - RF2 OFF ON Examples of Typical Operating Conditions - Idd & Ictl = 0.1 µA, Typical 14 - 3 Vdd (V) 0 (Unpowered) Vctl (V) 0 (Unpowered) 0 1.2 > 0.8 < 1.0 2.2 > 1.8 < 2.1 3.3 > 2.9 < 3.8 5.0 > 4.6 RF1 - RF2 ON OFF ON OFF ON OFF ON OFF ON For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC550 / 550E v01.1010 GaAs MMIC SPST FAILSAFE SWITCH, DC - 6 GHz Absolute Maximum Ratings RF Input Power (Vctl = 0/+3.3V) +34 dBm Supply Voltage (Vdd) +12 Vdc Control Voltage Range (Vctl) -0.2 to +(Vdd + 0.2) Vdc Hot Switch Power Level (Vctl = 0/+3.3V) +35 dBm Channel Temperature 150 °C Continuous Pdiss (T= 85 °C) (derate 6.67 mW/ °C above 85°C) 433 mW Thermal Resistance 150 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS DC blocks are required at ports RF1 and RF2. Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC550 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] H550 HMC550E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] 550E Switches - SPST - SMT 14 Package Marking [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 14 - 4 HMC550 / 550E v01.1010 GaAs MMIC SPST FAILSAFE SWITCH, DC - 6 GHz Pin Descriptions Switches - SPST - SMT 14 14 - 5 Pin Number Function Description 1, 3 RF1, RF2 These pins are DC coupled and matched to 50 Ohms. Blocking capacitors are required. 2, 5 GND These pins must be connected to RF ground. 4 Vdd Supply Voltage 6 Vctl See truth and control voltage tables. Interface Schematic Typical Application Circuit Note: 1. DC Blocking capacitors are required for each RF port as shown. Capacitor value determines lowest frequency of operation. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC550 / 550E v01.1010 GaAs MMIC SPST FAILSAFE SWITCH, DC - 6 GHz Evaluation PCB List of Materials for Evaluation PCB 109266 [1] Item Description J1 - J2 PCB Mount SMA RF Connector J3 - J5 DC Pin C1 1,000 pF Capacitor, 0402 Pkg. C2 - C3 100 pF capacitor, 0402 Pkg. R1, R2 100 Ohm Resistor, 0402 Pkg. U1 HMC550 / HMC550E SPST Switch PCB [2] 108436 Evaluation PCB The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 Ohm impedance and the package ground leads should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. Switches - SPST - SMT 14 [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 14 - 6