Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Typical Applications Features The HMC607G7 is ideal for: • Telecom Infrastructure High Isolation: 55 dB @ 2 GHz 42 dB @ 6 GHz • Microwave Radio & VSAT Low Insertion Loss: 1.9 dB Typical @ 6 GHz • Military Radios, Radar & ECM Non-Reflective Design • Space Systems Hermetic Surface Mount Package • Test Instrumentation Higher Performance Drop-In Replacement for: Skyworks AS406M2-10 Functional Diagram 10 General Description SWITCHES - SMT The HMC607G7 is a broadband high isolation non-reflective GaAs MESFET SPDT switch in a hermetic surface mount package. Covering DC to 6 GHz, the switch features >55 dB isolation up to 2 GHz and >42 dB isolation up to 6 GHz. The switch operates using complementary negative control voltage logic lines of -5/0V and requires no bias supply. Electrical Specifi cations, TA = +25° C, With 0/-5V Control, 50 Ohm System Parameter 10 - 372 Frequency Insertion Loss DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz Isolation DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz Min. 50 41 37 Typ. Max. Units 1.3 1.4 1.9 1.6 1.7 2.3 dB dB dB 55 46 42 dB dB dB Return Loss “On State” DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz 20 17 13 dB dB dB Return Loss RF1, RF2 “Off State” DC - 2.0 GHz DC - 4.0 GHz DC - 6.0 GHz 13 13 13 dB dB dB 27 dBm Input Power for 1 dB Compression 0.5 - 6.0 GHz 23 Input Third Order Intercept (Two-Tone Input Power= +7 dBm Each Tone, 1 MHz Tone Separation) 0.5 - 6.0 GHz 47 dBm Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) DC - 6.0 GHz 3 6 ns ns For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Insertion Loss Isolation 0 -1 RF1 RF2 -20 ISOLATION (dB) -2 +25 C +85 C -40 C -3 -40 -60 -4 -5 -80 0 1 2 3 4 5 6 0 7 1 2 FREQUENCY (GHz) Return Loss 4 5 6 7 10 0.1 and 1 dB Input Compression Point 35 0 COMPRESSION POINT (dBm) RFC RF1, RF2 on RF1, RF2 off -5 -10 -15 -20 1 dB Compression Point 0.1 dB Compression Point 30 25 20 15 -25 0 1 2 3 4 5 6 7 0 1 2 FREQUENCY (GHz) 3 4 5 FREQUENCY (GHz) 6 7 Input Third Order Intercept Point 60 55 50 IP3 (dBm) RETURN LOSS (dB) 3 FREQUENCY (GHz) SWITCHES - SMT INSERTION LOSS (dB) 0 45 40 +25 C +85 C -40 C 35 30 0 1 2 3 4 5 FREQUENCY (GHz) 6 7 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 373 HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Absolute Maximum Ratings Control Voltages RF Input Power (A, A, B, B = 0/-5V) (0.5 - 6 GHz) +30 dBm (@ +50 °C) Control Voltage Range (A, A, B, B) +1.0V to -7.5 Vdc Channel Temperature 150 °C Thermal Resistance (RTH) (junction to lead) 94 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C State Bias Condition Low 0 to -0.2V @ 10 uA Max. High -5V @ 10 uA Typ. to -7V @ 45 uA Typ. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Truth Table Control Input SWITCHES - SMT 10 10 - 374 B B Signal Path State A A RFC to RF1 RFC to RF2 OFF Low High Low High ON High Low High Low OFF ON High Low Low High OFF OFF Low High High Low ON ON Caution: Do not “Hot Switch” power levels greater than +27 dBm (A, A, B, B = 0/-5V). Suggested Driver Circuit for Single Line Control For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Outline Drawing SWITCHES - SMT 10 NOTES: 1. PACKAGE BODY MATERIAL: WHITE ALUMINA 92% 2. CONDUCTOR TRACES MATERIAL: THICK FILM TUNGSTEN. 3. LEAD, BASE, COVER MATERIAL: KOVAR™. 4. PLATING: ELECTROLYTIC GOLD 50 MICROINCHES MIN, OVER ELECTROLYTIC NICKEL 50 MICROINCHES MIN. 5. ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]. 6. TOLERANCES: .±005 [0.13] UNLESS OTHERWISE SPECIFIED. 7. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Pin Descriptions Pin Number Function Description 1, 2, 3 RF2, RFC, RF1 This pin is DC coupled and matched to 50 Ohm. Blocking capacitors are required if RF line potential is not equal to 0V. 4 B 5 B 6 A 7 A Interface Schematic See truth table and control voltage table. GND Package bottom must also be connected to PCB RF ground. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 375 HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Evaluation PCB SWITCHES - SMT 10 List of Materials for Evaluation PBC 116577 [1] Item Description J1 - J3 PCB Mount SMA RF Connector J4 - J8 DC Pin R1 - R4 100 Ohm Resistor, 0402 Pkg. U1 HMC607G7 SPDT Switch PCB [2] 116575 Evaluation PCB [1] Reference this number when ordering complete evaluation PCB The circuit board used in the final application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. [2] Circuit Board Material: Rogers 4350 10 - 376 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC607G7 v00.0307 GaAs MMIC SMT HIGH ISOLATION SPDT SWITCH, DC - 6 GHz Notes: SWITCHES - SMT 10 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 377