® ISOCOM LTD IECQ QC 88000-C002 COMPONENT ISSUE 5 SPECIFICATION May 2013 Component Specification For Ceramic Hermetically Sealed High Speed Optocouplers M1077 IECQ IECQ Product Certificate Number E1280/F Up-to-date lists and bibliographical references of IECQ publications may be downloaded from www.iecq.org Further copies of this document may be obtained from: IEC International Electrotechnical Commission Commission Electrotechnique Internationale Box 131, rue de Varembé, CH 1211 Geneva 20, Switzerland For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 1 of 12 QC 88000-C002: 2013 ® ISOCOM LTD FOREWORD The IECQ Quality Assessment System for Electronic Components (IECQ) is composed of those member countries of the International Electrotechnical Commission (IEC) who wish to take part in a harmonized system for electronic components of assessed quality. IECQ is also known in some European member countries as IECQ-CECC. The object of the System is to facilitate international trade by the harmonization of the specifications and quality assessment procedures for electronic components, and by the grant of an internationally recognised Mark, or Certificate of Conformity. The components produced or services provided under the system are thereby acceptable in all member countries without further testing. This Component Specification is based upon the requirements of IECQ 03-3, Annex E (QC 001002-2 Amendment 1, Clause 5.4) and has been prepared by: Isocom Ltd 48 Hutton Close Crowther Industrial Estate Washington Tyne and Wear NE38 0AH United Kingdom Tel: Fax: +44 0191 4166 546 +44 0191 4155 055 and published under the authority of: BSI Group Kitemark Court Davy Avenue Knowlhill Milton Keynes MK5 8PP United Kingdom AMENDMENT RECORD Issue 1 – Changed Page 4 – Amendments 06/07/09 Issue 2 – Changed Pages 3, 4, 5 & 6 – RoHS Compliant & Amendments – 13/07/10 Issue 3 – Changed Page 6 – Added 4/5 pin hybrid outline drawing – 26/5/11 Issue 4 – Changed Page 4, text changed on selection guide, change to drawing for CSM168-2, changed Page 5 changed description of 16 pin DIP, changed text on document footer 30/5/13 REQUIREMENTS The requirements for IECQ Component Specifications as detailed in IECQ 03-3, Annex E (QC 001002-2 Amendment 1, Clause 5.4) are satisfied by the following data sheet. It should note that IECQ are not responsible for manufacturers declarations made in data sheets which fall outside the limits of approved detailed in IECQ certificates. This Component Specification is intended for use with applicable IECQ Assessment Specifications. Eg: QC 88000A0001 For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 2 of 12 QC 88000-C002: 2013 ® ISOCOM LTD Ceramic Hermetically Sealed, Radiation Hard High Speed Optocoupler ■ ■ ■ ■ ■ 4N55 CD850 CH380 CS800/801 CSM168-2 ■ ■ ■ ■ CSM168-4 CSM1800 CSM1801 MC800 Features Applications ▪ Release to IECQ ▪ Military, high reliability system ▪ Hermetically Sealed ▪ Medical instruments ▪ High Density Packaging ▪ Mos, Cmos Applications ▪ 1500V DC withstand Test Voltage ▪ Logic Interfacing ▪ Low Input Requirements ▪ Data Transmission ▪ High Current Transfer Ratio ▪ Power Supply ▪ RoHS Compliant Description These devices are single, dual and quad, hermetically sealed optocouplers. Each channel is composed of an infra-red light emitting diode and a photon detector high speed transistor output. Package styles for these devices include 6 pin, 8 pin, 16 pin flat pack, 6 pin LCC and hybrid 6 pin, with surface mount, butt cut and gull wing options available. Separate connections for the photodiodes and output transistor collectors improve the speed up to a hundred times that of a conventional phototransistor optocoupler by reducing the base-collector capacitance. The same electrical die, assembly processes and materials are used for each channel of each device shown below. Therefore absolute maximum ratings, recommended operating conditions, electrical specifications and performance characteristics are identical for all units. Any exceptions, due to packaging variations and limitations, are as noted. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 3 of 12 QC 88000-C002: 2013 ® ISOCOM LTD Selection Guide Package Styles and Configuration Options 6pin metal Can TO-5 5 pin Hybrid 6 Pad LCC 8 pin DIP 16 pin DIP 16 pin Flat Pack 1 1 1/2 2 2/4 MC800 CH380 CSM1800/01 4N55 CSM168 MC800/L2 CH380/L2 CSM1800/01/L2 4N55/L2 CSM168/L2 MC800/L2S Gold Plate CH380/L2S Gold Plate CSM1800/01/L2S Gold Plate 4N55/L2S Gold Plate Option 20 Option 10 Option 30 Option 60 CSM168/L2S Gold Plate Package Lead Style 1 Channels Common Channel Wiring Isocom Part Numbers and Options Commercial Defense Level Space Level Standard Gold Plate Finish Solder Dipped Butt Cut/Gold Plate Gull Wing/Soldered Crew Cut/Gold Plate CD850 CS800/801 CD850/L2 CS800/801/L2 CD850/L2S CS800/801/L2S Gold Plate Option 20 Option 10 Option 30 Option 60 Functional Diagrams 5 MC800 CH380 CSM1800/01 CD850 4N55 CSM168-2 6 pin TO-5 1 Channel 5 pin Hybrid 1 Channel 6 pad LCC 1 Channel 8 pin DIP 2 Channel 16 pin DIP 2 Channel 16 pin Flat Pack 2 Channel 3 2 7 1 CS800/801 CSM168-4 8 pin DIP 1 Channel 16 pin Flat Pack 4 Channel For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 4 of 12 QC 88000-C002: 2013 ® ISOCOM LTD Outline Drawings 16 pin DIP 16 pin Flat Pack, 2 and 4 Channel NOTE: DIMENSIONS IN MILLIMETERS 6 pin TO-5, 1 Channel 0.040(1.02) 6 LEADS 0.0175 (0.445) 45. 0° 0.32 (8.13) 5 3 0.037 (0.935) 6 7 2 1 0.5 (12.70) 0.022 (5.08) 0.031 (0.787) 0.17 (4.32) For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 5 of 12 QC 88000-C002: 2013 ® ISOCOM LTD 8 pin DIP 1 and 2 Channel 6 Terminal LCC Surface Mount, 1 Channel 1.651 2.286 6.223 0.635 5 6 4 1 3 2 1.27 4.318 CSM1800 2.54 1.67 0.762 0.635 R = .2286 4/5 Terminal Hybrid, 1 Channel 3.5 0.6 4.5 0.13 2.0 0.7 0.13 0.6 +0.2 +0.2 0.6 Device Marking Isocom Part Number XXXXXXX Manufacturer ISOCOM XXXX Date Code (XX year XX week) For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 6 of 12 QC 88000-C002: 2013 ® ISOCOM LTD Hermetic Optocoupler Options Option 10 Description Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial hi-rel product in 8 and 16 pin DIP 20 30 Surface mountable hermetic optocoupler with leads cut and bent for gull wing assembly. This option is available on commercial and hi-rel product in 8 and 16 pin DIP. 60 Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial hi-rel product in 8 and 16 pin DIP For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 7 of 12 QC 88000-C002: 2013 ® ISOCOM LTD Absolute Maximum Ratings Storage Temperature Operating Temperature -65°C to +150°C -55°C to +125°C Input Diode Peak Forward Current Average Forward Current Reverse Voltage Power Dissipation 40mA 20mA 5V 36mW 1 mS duration Derate linearly above 100°C at 1.4W/°C for CH380 and CS800/801 Output Detector Supply Voltage Average Current Peak Current Voltage Power Dissipation -0.5 to 20V 8mA 16mA -0.5 to 20V 40mW 50mW Emitter-Base Reverse Voltage Base Current 3V 5mA VCC IO IO VO For CH380 and CS800/801 Derate linearly above 100°C at 1.4W/°C for CD850, CSM6530 and 4N55 BVEBO IB Single Channel Schematic For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 8 of 12 QC 88000-C002: 2013 ® ISOCOM LTD Electrical Characteristics TA = -55°C to +125°C U.O.S. All typical values at VCC = 5V, TA = 25°C (each channel where appropriate). Parameter Current Transfer Ratio (See notes 1 & 2) Logic Low Output Voltage Logic High Output Current (See note 1) Symbol hf(CTR) VOL IOH Logic Low Supply Current (See note 1) ICCL Logic High Supply Current (See note 1) Input Forward Voltage (See note 1) Input Reverse Breakdown (See note 1) Input-Output Insulation Leakage Current (See notes 3 & 9) ICCH Propagation Delay Time to Logic Low at Output (See note 1) tPHL Test Conditions VCC = 4.5V, VO = 0.4V,IF = 16mA, VCC = 4.5V, VO = 0.5V, IF = 16mA VCC = 4.5V, IF = 16mA IO = 1.44mA IF1 = 0, IF2 = 20mA VO = VCC = 18V IF1 = F2 = 20mA, VO = VCC = 15 VCC = 18V, IF1 = IF2 = 20Ma VCC = 18V, IF1 = 20Ma VCC = 15V IF1 = 16Ma IF2 =0 CS801 CD850 CD850 Min 9 15 9 - Type 20 17 0.3 0.3 30 Max - Units % 0.4 0.5 250 µA - 30 200 µA - 0.4 400 10 µA - 1.45 1.9 V V CD850 CSM1800 CS800/1 CH380 CSM1800 CD850 VF VCC = 16VF1 = IF2 =16mA Vcc = 18V, IF = 0mA, IF (other channel) = 20mA IF = 20mA VBR IR = 10µA 3 - - V IIO RH = 45%, TA = 25°C, t = 5S VIO = 1500VDC RH = 45%, TA = 25°C, t = 5S VIO = 500VDC RL = 8.2KΩ, IF = 16mA, VCC = 5V CL = 50pF - - 1.0 µA - 0.4 2.0 µS RL = 1.9K, IF = 16mA, VCC = 5V Propagation Delay Time to Logic High at Output (See note 1) Device tPLH CH380 CD850 CSM1800 - RL = 8.2KΩ, IF = 16mA, VCC = 5V CL = 50pF RL = 1.9K, IF = 16mA, VCC = 5V 2.0 CD850 CSM1800 2.0 6.0 µS 6.0 For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 9 of 12 QC 88000-C002: 2013 ® ISOCOM LTD Typical Characteristics TA = 25°C Parameter Temperature Coefficient of Forward Voltage Input Capacitance Resistance (Input-Output) Capacitance (Input-Output) Input-Input Insulation Leakage Current Capacitance (Input-Input) Transistor DC Current Gain Small Signal Current Transfer Ratio Common Mode Transient Immunity at Logic Low Level Output Common Mode Transient Immunity at Logic High Level Output Bandwidth Symbol VF TA CIN RI-O CI-O II-I CI-I hFE IO IF CML CMH BW Test Conditions IF = 20mA Notes 1 Min - Type -1.9 Max - Units mV/°C f = 1mhz, VF = 0 V1-0 = 500Vdc f = 1MHz 45% Relative Humidity VH = 500Vdc, t = 5S f = 1MHz VO = 5V, IO = 3mA VCC = 5V, VO = 2V 1 1 1&4 5 - 125 1012 1.0 1 - pF Ω pF pA 5 1 1 - 0.6 130 20 - pF % IF = 16mA,RL = 8.2KΩ VCM = 10VP-P VO (max) = 0.8V IF = 0mA,RL = 8.2KΩ VCM = 10VP-P VO (max) = 2.0V RL = 100Ω 1&7 - -1000 - V/µS 1&6 - 1000 - V/µS 8 - 2 - MHz Notes (Apply typically to 16 pin package) 1. Each channel, where appropriate. 2. Current Transfer ratio is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100%. CTR is known to degrade slightly over the unit’s lifetime as a function of input current, temperature, signal duty cycle and system on time. It is recommended that designers allow at least 20-25% guard band for CTR degradation. 3. Measured between pins 1 through 8 shorted together, and pins 9 through 16 shorted together. 4. Measured between each input pair shorted together, and the output pins for that channel shorted together. 5. Measured between pins 3 and 4 shorted together, and pins 7 and 8 shorted together. 6. CMH is the steepest slope (dV/dt) on the leading edge of the common mode pulse, VCM, for which the output will remain in the logic high state (i.e., VO > 2.0V). 7. CML is the steepest slope (dV/dt) on the trailing edge of the common mode pulse, VCM, for which the output will remain in the logic low state (i.e., VO < 0.8V). 8. Bandwidth is the frequency at which the AC output voltage is 3dB below the low frequency asymptote. 9. This is a momentary withstand test, not an operating condition. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 10 of 12 QC 88000-C002: 2013 ® ISOCOM LTD Electrical Characteristics For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 11 of 12 QC 88000-C002: 2013 ® ISOCOM LTD For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, UK, NE38 0AH Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 12 of 12 QC 88000-C002: 2013