ISOCOM LTD ® PART NUMBER CSM100/101/L2S COMPONENT ISSUE 2 SPECIFICATION June 2014 Component Specification For Ceramic Hermetically Sealed, Radiation Hard Transistor Optocouplers M1077 IECQ 1077/M Further copies of this document may be obtained from: ISOCOM LIMITED WASHINGTON, UK NE38 0AH www.isocom.uk.com For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 1 of 12 ISOCOM LTD ® Ceramic Hermetically Sealed, Radiation Hard Transistor Optocouplers ■ CSM100/101 ■ CSM100/101/L2 ■ CSM100/101/L2S Features Applications ▪ Released to European Standard and Complies to Mil Std ▪ Space Radiation Equipment ▪ Military, high reliability system ▪ Total Ionizing Dose Tested to 150KRad(si) ▪ Medical instruments ▪ Displacement Damage to 1 MEV x 10¹² ▪ Logic Interfacing ▪ High Isolation Voltage 1000vdc ▪ Mos, Cmos Applications ▪ 4 Pin LCC Package ▪ Data Transmission ▪ Low Input Requirements ▪ Power Supply ▪ High Current Transfer Ratio ▪ Modems High Speed Switching Hermetically Sealed Description These devices are single, hermetically sealed optically coupled isolators. Each channel is composed of a infra-red emitting diode and a silicon phototransistor. The CSM100 series is being used in environments encounted by space applications. It is manufactured to meet the JANS standard in conjunction with MIL-PRF-19500 procedures (please see next page for all other applicable specifications). Package styles for this device include 4 Pin LCC Package with surface mount, solder dip option available. Therefore absolute maximum ratings, recommended operating conditions, electrical specifications and performance characteristics are identical for all units. Any exceptions, due to packaging variations and limitations, are as noted. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 2 of 12 ISOCOM LTD ® Standards The following specifications have been complied with in the manufacturing of this product: Military Compliance Specifications MIL-PRF-19500 – General Specification for Discrete Semiconductor Devices IECQ – M1077 Military Compliance Standards MIL-STD-202 – Test Method Standard Electronic and Electrical Component Parts MIL-STD-883 – Test Method Standard Microcircuits MIL-STD-750 – Test Methods for Semiconductor Devices ISO 9001:2008 – Manufacturing of Optocouplers and Optoelectronic components. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 3 of 12 ISOCOM LTD ® Selection Guide Package Styles and Configuration Options Package Lead Style Channels Common Channel Wiring Isocom Part Number and Options Commercial Defense Screen Level Space Screen Level Standard Gold Plate Finish Solder Dipped 4 pin LCC 1 CSM100/101 CSM100/101/L2 CSM100/101/L2S Gold Plate Option 20 Functional Diagrams CSM100 CSM101 4 pin LCC 1 Channel 4 pin LCC 1 Channel Device Marking ISOCOM XXXXXXX XXXX For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 4 of 12 Manufacturer Isocom Part Number Date Code (XX year XX week) ISOCOM LTD ® Outline Drawings C A K L B I Lid grounding stripe J D H 0.2286 R E G F Inches SYMBOL A B C D E F G H I J K L MIN. 0.215 0.145 0.061 0.045 0.032 0.072 0.032 0.022 0.010 0.029 0.036 0.011 Millimetres MAX. 0.225 0.155 0.075 0.055 0.048 0.088 0.048 0.028 0.024 0.044 0.044 0.019 MIN. 5.46 3.68 1.55 1.14 0.81 1.83 0.81 0.56 0.25 0.74 0.91 0.28 For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 5 of 12 MAX. 5.71 3.94 1.91 1.40 1.22 2.24 1.22 0.71 0.61 1.12 1.12 0.48 ISOCOM LTD ® Absolute Maximum Ratings TA = 25°C U.O.S. Storage Temperature Operating Temperature Lead Soldering Temperature Input-to-Output Isolation Voltage -65°C to +150°C -55°C to +125°C 260°C 1.6mm from case for 10S 1000VDC Input Diode Forward DC Current 40mA Reverse DC Voltage Peak forward Current Power Dissipation 2V 1.0mA 60mW DC at (or below) +65°C Derates linearly to +125°C free air temperature at the rate of 0.67mA/°C. Pw1µS, PRR<300pps 10µS ms Derates linearly above 65°C at 1.0W/°C Output Transistor Collector-Emitter Voltage Emitter-Collector Voltage Collector Current Power Dissipation 40V 5V 50mA 300mW BVCEO BVECO Derates linearly above 25°C at 3.0W/°C Coupled Device Input to Output Isolation Voltage Power Dissipation SolderingTemperature,Soldering Iron 1000V 360mW 260,5 SolderingTemperature,Vapour Phase 220,40 ESD Classification Class 2 °C,s This part shall not be re-soldered until 3 minutes have elapsed. °C,s This part shall not be re-soldered until 3 minutes have elapsed. Class 2 with minimum critical path voltage of 4,000 to 15,999V. MIL-STD-883 Recommended Operating Conditions Characteristics Symbol Supply Voltage Operating Temperature VCE TOP Maximum Range 5.0 to 20 -55 to 125 Unit V O C For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 6 of 12 Comments ISOCOM LTD ® Electrical Characteristics Input Diode Electrical Characteristics TA = 25°C U.O.S. Parameter Forward Voltage Symbol VF Reverse Current IR Test Conditions IF = 10mA IF = 10mA -55°C IF = 10mA +125°C VR = 2.0V Min 1.3 1.3 1.1 - Type - Max 1.6 1.8 1.6 100 Units V V V µA 70 100 - V 7 9 - V - 7 10 100 100 150 µA µA µA 200 200 100 350 100 300 - - - - 0.22 % % % % % % V 1000 - 105 - 20.0 Vdc Ω µS - - 20.0 µS - - 5.0 µS - - 5.0 µS 200 200 100 100 66 66 160 160 40 40 250 250 - - % % % % % % % % % % % % Output Detector Electrical Characteristics Collector-Emitter Breakdown Voltage Emitter-Collector Breakdown Voltage Collector–Emitter Leakage Current V(BR)CEO V(BR)ECO ICEO IC = 1mA IE = 0.1mA VCE = 20v, IF = 0 VCE = 20v IF = 0, -55°C VCE = 20v, IF = 0, +125°C Coupled Electrical Characteristics DC Current Transfer Ratio IC/IF Collector-Emitter Saturation Voltage Isolation Voltage Input to Output Resistance Rise Time VCE (Sat) V in-out R in-out tr Fall Time tf Propagation Delay H-L tPHL Propagation Delay L-H tPLH DC Current Transfer Ratio IC (note 2) (note 2) IF = 1.0mA, VCE = 1V IF = 3.0mA, VCE = 1V IF = 15.0mA, VCE = 1V IF = 10.0mA, VCE = 5V (Note 1) IF = 15.0mA, VCE = 5V (Note 1) IF = 1.0mA, VCE = 15V IC =10.0mA IF = 20mA T = 5s (Note 2) VIO = 500V (Note 2) RL = 100Ohms Vcc = 10V IF = 10mA RL = 100Ohms Vcc = 10V IF = 10mA RL = 100Ohms Vcc = 10V IF = 10mA RL = 100Ohms Vcc = 10V IF = 10mA IF = 1.0mA, VCE = 1V, TA = 125°C IF = 1.0mA, VCE = 1V, TA = -55°C IF = 3.0mA, VCE = 1V, TA = 125°C IF = 3.0mA, VCE = 1V, TA = -55°C IF = 15.0mA, VCE = 1V, TA = 125°C IF = 15.0mA, VCE = 1V, TA = -55°C IF = 10.0mA, VCE = 5V; TA =125°C IF = 10.0mA, VCE = 5V, TA = -55°C IF = 15.0mA, VCE = 5V, TA = 125°C IF = 15.0mA, VCE = 5V, TA = -55°C IF = 1.0mA, VCE = 15V, TA = 125°C IF = 1.0mA, VCE = 15V, TA = -55°C Notes: 1) Sample and hold pulse shall not be longer than 0.1 seconds. Duty cycle shall be 10. 2) Measurements with inputs shorted together and outputs shorted together. For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 7 of 12 ISOCOM LTD ® Electrical Measurements During and on Completion of Radiation Testing Parameter Input Diode Forward Voltage Input Diode Reverse Current Photo Transistor CollectorEmitter Dark Current Coupled Current Transfer Ratio Collector-Emitter Saturation Voltage Symbol VF Test Conditions IF = 10mA Min 1.3 Max 1.8 Units V IR VR = 2.0V - 100 µA ICEO VCE = 20v, IF = 0 - 100 µA IC IF = 1.0mA, VCE = 1V 200 - % VCE (Sat) IF = 3.0mA, VCE = 1V IF = 15.0mA, VCE = 1V IF = 10.0mA, VCE = 5V (note 1) IF = 15.0mA, VCE = 5V (note 1) IF = 1.0mA, VCE = 15V IC =10.0mA IF = 20mA 100 100 250 100 250 - 0.22 % % % % % V NOTE 1 = Sample and hold pulse shall be not longer than 0.1 seconds. Duty cycle shall be 10 Switching Time For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 8 of 12 ISOCOM LTD ® GROUP TESTING TO MIL-STD 750 GROUP TEST MIL‐STD‐750 Group A SG1 Visual inspection & mechanical dimensions DC static test at 25°C DC static test at 125°C and ‐55°C Dynamic test at 25°C Physical dimensions Solderability Resistance to solvents Thermal Shock Method 2071 SG2 SG3 SG4 Group B SG 1 SG 2 SG 3 SG 4 SG 5 Group C SG 2 Temperature cycling Hermetic seal fine and gross leak Electrical measurement Decap internal visual inspection Bond strength Die shear Intermittent operation life Hermetic seal fine and gross leak Electrical measurement Bond strength Acc. steady‐state operation life Electrical measurement Bond strength Thermal Shock Temperature cycling SG 3 Hermetic seal fine and gross leak Moisture resistance Electrical measurement Mechanical shock Vibration Constant acceleration SG 6 Electrical measurement Steady state operating life Not required as B5 is available on same lot Method 2066 Method 2026 Method 1022 Method 1056 Cond. B, 25 cycles Method 1051, 100 cycles, ‐ 55/+125°C Method 1071, Cond. H (fine), Cond. C (gross) pre and post 2075 Method 2037, Cond. D Method 2017 Method 1037, 1042, Cond D, Tab.5‐5 Method 1071, Cond. H (fine), Cond. C (gross) pre and post Method 2037, Cond. D Method 1027 yes yes yes pre and post Method 2037, Cond. D Method 1056, Cond. B, 25 shocks Method 1051, Cond. C, ‐55/+125°C , 25 cycles (total 45 cycles including screening) Method 1071, Cond. H (fine), Cond. C (gross) Method 1021 pre and post Method 2016, non‐operating, 1500 G, 0.5 ms, 5 blows in each orientation (X1,Y1,Z1) Method 2056 Method 2006, at a peak level of 5000 G pre and post yes yes For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 9 of 12 READ AND RECORD yes yes yes yes yes yes yes ISOCOM LTD ® 100% SCREENING TO MIL-STD 750 TEST MIL-STD-750 Internal Visual 2072 READ AND RECORD? Sealing (Fine Leak) (Gross Leak) Temp Cycling Const. Acceler PIND Radiography Initial Electrical HTRB Interim Electrical Burn-In Final Electrical PDA (Fine Leak) (Gross Leak) 1071, Condition H1 1071, Condition C 1051, Condition B‐55/+125°C, 20 Cycles. 2006, 5000G, Y1 only. 2052, Condition A 2076 125°C, ‐55°C, 25°C 1039 25°C only 1039 125°C, ‐55°C, 25°C Max. 5%, pre/post B1 electrical and delta at RT only 1071, Condition H1 1071, Condition C R&R R&R R&R Calculate & R Solder Dip Fine Leak Gross Leak 1071, Condition H1 1071, Condition C For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 10 of 12 ISOCOM LTD ® For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 11 of 12 ISOCOM LTD ® For sales enquiries, or further information, please contact our sales office at: Isocom Ltd, 48, Hutton Close, Crowther Industrial Estate, Washington, Tyne and Wear, NE38 0AH, UK Tel: +44 0191 4166 546 Fax: +44 0191 4155 055 ©2007 Copyright reserved to Isocom Limited Page 12 of 12