TI TRSF23243CDGGRG4

TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
FEATURES
•
•
•
•
•
•
•
•
•
•
•
Single-Chip and Single-Supply Interface for
Two IBM PC/AT Serial Ports
Meets or Exceeds the Requirements of
TIA/EIA-232-F and ITU v.28 Standards
Operates With 3-V to 5.5-V VCC Supply
Always-Active Noninverting Receiver Output
(ROUT2) Per Port
Operates Up To 250 kbit/s
Low Standby Current . . . 1 μA Typical
External Capacitors . . . 4 × 0.22 μF
Accepts 5-V Logic Input With 3.3-V Supply
Allows for Flexible Power Down of Either
Serial Port
Serial-Mouse Driveability
RS-232 Bus-Pin ESD Protection Exceeds
±15 kV Using Human-Body Model (HBM)
APPLICATIONS
•
•
•
•
•
Battery-Powered Systems
Notebooks
Laptops
Palmtop PCs
Hand-Held Equipment
DESCRIPTION/ORDERING INFORMATION
The TRSF23243 consists of two ports, each containing three line drivers and five line receivers, and a dual
charge-pump circuit with ±15-kV ESD protection pin to pin (serial-port connection pins, including GND). This
device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous
communication controller and the serial-port connector. This combination of drivers and receivers matches that
needed for two typical serial ports used in an IBM PC/AT, or compatible. The charge pump and four small
external capacitors allow operation from a single 3-V to 5.5-V supply. In addition, this device includes an
always-active noninverting output (ROUT2) per port, which allows applications using the ring indicator to
transmit data while the device is powered down. The device operates at data signaling rates up to 250 kbit/s and
a maximum of 30-V/μs driver output slew-rate.
ORDERING INFORMATION
TA
0°C to 70°C
PACKAGE
SSOP – DL
TSSOP – DGG
–40°C to 85°C
SSOP – DL
TSSOP – DGG
(1)
(2)
(1) (2)
ORDERABLE PART NUMBER
Tube of 25
TRSF23243CDL
Reel of 1000
TRSF23243CDLR
Reel of 2000
TRSF23243CDGGR
Tube of 25
TRSF23243IDL
Reel of 1000
TRSF23243IDLR
Reel of 2000
TRSF23243IDGGR
TOP-SIDE MARKING
TRSF23243C
TRSF23243C
TRSF23243I
TRSF23243I
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007, Texas Instruments Incorporated
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
DESCRIPTION/ORDERING INFORMATION (CONTINUED)
Flexible control options for power management are available when either or both serial ports are inactive. The
auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of
operation, if the device does not sense a valid RS-232 signal, the driver outputs of its respective port are
disabled. If FORCEOFF is set low, both drivers and receivers (except ROUT2) are shut off, and the supply
current is reduced to 1 μA. Disconnecting the serial port or turning off the peripheral drivers causes the
auto-powerdown condition to occur.
Auto-powerdown can be disabled when FORCEON and FORCEOFF are high and should be done when driving
a serial mouse. With auto-powerdown enabled, the RS-232 port is activated automatically when a valid signal is
applied to any respective receiver input. The INV output is used to notify the user if an RS-232 signal is present
at any receiver input. INV is high (valid data) if any receiver input voltage is greater than 2.7 V or less than –2.7
V or has been between –0.3 V and 0.3 V for less than 30 μs. INV is low (invalid data) if all receiver input
voltages are between –0.3 V and 0.3 V for more than 30 μs. Refer to Figure 5 for receiver input levels.
FUNCTION TABLES
ABC
Each Driver (1)
(Each Port)
INPUTS
DIN
(1)
FORCEON
FORCEOFF
VALID RIN
RS-232 LEVEL
OUTPUT
DOUT
DRIVER STATUS
X
X
L
X
Z
Powered off
L
H
H
X
H
H
H
H
X
L
Normal operation with
auto-powerdown disabled
L
L
H
Yes
H
H
L
H
Yes
L
L
L
H
No
Z
H
L
H
No
Z
Normal operation with
auto-powerdown enabled
Powered off by
auto-powerdown feature
H = high level, L = low level, X = irrelevant, Z = high impedance
Each Receiver (1)
(Each Port)
INPUTS
RIN2
RIN1,
RIN3–RIN5
L
H
FORCEOFF
ROUT2
ROUT
X
L
X
L
Z
X
L
X
H
Z
L
L
H
Yes
L
H
L
H
H
Yes
L
L
H
L
H
Yes
H
H
H
H
H
Yes
H
L
Open
Open
H
No
L
H
(1)
2
OUTPUTS
VALID RIN
RS-232 LEVEL
H = high level, L = low level, X = irrelevant,
Z = high impedance (off),
Open = input disconnected or connected driver off
Submit Documentation Feedback
RECEIVER STATUS
Powered off while
ROUT2 is active
Normal operation with
auto-powerdown
disabled/enabled
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
LOGIC DIAGRAM (POSITIVE LOGIC)
RIN5A
RIN4A
RIN3A
RIN2A
RIN1A
1
48
2
47
3
46
4
45
5
44
43
INVA
DOUT3A
DOUT2A
DOUT1A
6
ROUT4A
ROUT3A
ROUT2A
ROUT1A
ROUT2A
Auto-Powerdown
7
42
8
41
9
40
39
FORCEOFFA
ROUT5A
DIN3A
DIN2A
DIN1A
FORCEON
10
Charge
Pump
FORCEOFFB
DOUT1B
DOUT2B
DOUT3B
INVB
15
16
33
17
32
18
31
19
RIN2B
RIN3B
RIN4B
RIN5B
DIN2B
DIN3B
Auto-Powerdown
30
RIN1B
DIN1B
20
29
21
28
22
27
23
26
24
25
Submit Documentation Feedback
ROUT2B
ROUT1B
ROUT2B
ROUT3B
ROUT4B
ROUT5B
3
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
Timing
Figure 1 shows how the two independent serial ports can be enabled or disabled. As shown by the logic states,
depending on the FORCEOFF, FORCEON, and receiver input levels, either port can be powered down.
Intermediate receiver input levels indicate a 0-V input. Also, it is assumed a pulldown resistor to ground is used
for the receiver outputs. The INV pin goes low when its respective receiver input does not supply a valid RS-232
level. For simplicity, voltage levels, timing differences, and input/output edge rates are not shown.
FORCEOFFA
FORCEOFFB
FORCEON
0V
RIN2A
0V
RIN2B
DINA
DINB
ROUT2A
ROUT2A
ROUT2B
ROUT2B
DOUTA
0V
DOUTB
0V
INVA
INVB
A
B
C
A.
Ports A and B manually powered off.
B.
Port A manually powered off, port B in normal operation with auto-powerdown enabled.
C.
Port B powered off by auto-powerdown, port A in normal operation with auto-powerdown enabled.
D.
Port A in normal operation with auto-powerdown disabled, port B manually powered off.
E.
Ports A and B in normal operation with auto-powerdown disabled
Figure 1. Timing Diagram
4
D
Submit Documentation Feedback
E
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
Absolute Maximum Ratings
(1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCC
Supply voltage range (2)
–0.3
6
V
V+
Positive-output supply voltage range (2)
–0.3
7
V
0.3
–7
V
13
V
V–
Negative-output supply voltage range
V+ – V–
Supply voltage difference (2)
(2)
VI
Input voltage range
VO
Output voltage range
θJA
Package thermal impedance (3) (4)
TJ
Operating virtual junction temperature
Tstg
Storage temperature range
(1)
(2)
(3)
(4)
Driver (FORCEOFF, FORCEON)
–0.3
6
Receiver
–25
25
Driver
Receiver (INV)
–13.2
13.2
–0.3
VCC + 0.3
DGG package
70
DL package
63
–65
UNIT
V
V
°C/W
150
°C
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to network GND.
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions (1)
See Figure 7
VCC = 3.3 V
Supply voltage
VCC = 5 V
VIH
Driver and control
high-level input voltage
DIN, FORCEOFF, FORCEON
VIL
Driver and control
low-level input voltage
DIN, FORCEOFF, FORCEON
Driver and control input voltage
DIN, FORCEOFF, FORCEON
VI
TA
(1)
VCC = 3.3 V
VCC = 5 V
NOM
MAX
3
3.3
3.6
4.5
5
5.5
UNIT
V
2
V
2.4
0.8
Receiver input voltage
TRSF23243C
Operating free-air temperature
MIN
TRSF23243I
0
5.5
–25
25
0
70
–40
85
V
V
°C
Test conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 7)
PARAMETER
II
ICC
(1)
(2)
Input leakage
current
Supply current
(TA = 25°C)
TEST CONDITIONS
FORCEOFF, FORCEON
MIN
TYP (2) MAX
UNIT
±0.01
±1
μA
0.6
2
mA
Auto-powerdown disabled
No load,
FORCEOFF and FORCEON at VCC
Powered off
No load, FORCEOFF at GND
1
20
Auto-powerdown enabled
No load, FORCEOFF at VCC,
FORCEON at GND,
All RIN are open or grounded
1
20
μA
Test conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Submit Documentation Feedback
5
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
DRIVER SECTION
Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 7)
PARAMETER
TEST CONDITIONS
MIN
TYP (2)
MAX
UNIT
VOH
High-level output
voltage
All DOUT at RL = 3 kΩ to GND
5
5.4
V
VOL
Low-level output
voltage
All DOUT at RL = 3 kΩ to GND
–5
–5.4
V
VO
Output voltage
(mouse driveability)
DIN1 = DIN2 = GND, DIN3 = VCC,
3-kΩ to GND at DOUT3, DOUT1 = DOUT2 = –2.5 mA
±5
IIH
High-level input current VI = VCC
±0.01
±1
μA
IIL
Low-level input current
VI at GND
±0.01
±1
μA
IOS
Short-circuit output
current (3)
VCC = 3.6 V
VO = 0 V
VCC = 5.5 V
VO = 0 V
±35
±60
mA
ro
Output resistance
VCC, V+, and V– = 0 V,
VO = ±2 V
IOZ
(1)
(2)
(3)
Output leakage current FORCEOFF = GND,
V
300
Ω
10M
VO = ±12 V,
VCC = 3 V to 3.6 V
±25
VO = ±10 V,
VCC = 4.5 V to 5.5 V
±25
μA
Test conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one
output should be shorted at a time.
Switching Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 7)
PARAMETER
Maximum data rate
tsk(p)
Pulse skew
SR(tr)
Slew rate,
transition region
(see Figure 2)
(1)
(2)
(3)
6
(3)
TEST CONDITIONS
RL = 3 kΩ,
One DOUT switching
CL = 1000 pF,
See Figure 2
CL = 150 pF to 2500 pF,
RL = 3 kΩ to 7 kΩ,
VCC = 3.3 V,
RL = 3 kΩ to 7 kΩ
MIN TYP (2) MAX
UNIT
250
kbit/s
See Figure 2
100
ns
CL = 150 pF to 1000 pF
6
30
CL = 150 pF to 2500 pF
4
30
Test conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
Submit Documentation Feedback
V/μs
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
RECEIVER SECTION
Electrical Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 7)
PARAMETER
VOH
High-level output voltage
IOH = –1 mA
VOL
Low-level output voltage
IOL = 1.6 mA
TYP (2)
VCC – 0.6
VCC – 0.1
MAX
V
1.6
2.4
VCC = 5 V
1.9
2.4
Positive-going input threshold voltage
VIT–
Negative-going input threshold voltage
Vhys
Input hysteresis (VIT+ – VIT–)
IOZ
Output leakage current (except ROUT2B)
FORCEOFF = 0 V
rI
Input resistance
VI = ±3 V to ±25 V
UNIT
0.4
VCC = 3.3 V
VIT+
(1)
(2)
MIN
TEST CONDITIONS
VCC = 3.3 V
0.6
1.1
VCC = 5 V
0.8
1.4
V
V
V
0.5
3
V
±0.05
±10
μA
5
7
kΩ
Test conditions are C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Switching Characteristics (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 3)
PARAMETER
TEST CONDITIONS
TYP (2) UNIT
tPLH
Propagation delay time, low- to high-level
output
CL = 150 pF,
See Figure 4
150
ns
tPHL
Propagation delay time, high- to low-level
output
CL = 150 pF,
See Figure 4
150
ns
ten
Output enable time
CL = 150 pF,
See Figure 5
RL = 3 kΩ,
200
ns
tdis
Output disable time
CL = 150 pF,
See Figure 5
RL = 3 kΩ,
200
ns
50
ns
tsk(p)
(1)
(2)
(3)
Pulse skew
(3)
See Figure 4
Test conditions are C1–C4 = 0.22 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
Submit Documentation Feedback
7
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
AUTO-POWERDOWN SECTION
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
TEST CONDITIONS
MIN
VT+(valid)
Receiver input threshold for
INV high-level output voltage
FORCEON = GND,
FORCEOFF = VCC
VT(valid)
Receiver input threshold for
INV high-level output voltage
FORCEON = GND,
FORCEOFF = VCC
–2.7
VT(invalid)
Receiver input threshold for
INV low-level output voltage
FORCEON = GND,
FORCEOFF = VCC
–0.3
VOH
INV high-level output voltage
IOH = –1 mA,
FORCEOFF = VCC
FORCEON = GND,
VOL
INV low-level output voltage
IOL = 1.6 mA,
FORCEOFF = VCC
FORCEON = GND,
MAX
UNIT
2.7
V
V
0.3
V
VCC – 0.6
V
0.4
V
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
UNIT
tvalid
Propagation delay time, low- to high-level output
1
μs
tinvalid
Propagation delay time, high- to low-level output
30
μs
ten
Supply enable time
100
μs
(1)
8
TYP (1)
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Submit Documentation Feedback
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
PARAMETER MEASUREMENT INFORMATION
50 Ω
SR(tr) =
A.
CL includes probe and jig capacitance.
B.
The pulse generator has the following characteristics: PRR = 250 kbits/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤
10 ns.
Figure 2. Driver Slew Rate
50 Ω
A.
CL includes probe and jig capacitance.
B.
The pulse generator has the following characteristics: PRR = 250 kbits/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤
10 ns.
Figure 3. Driver Pulse Skew
3 V or 0 V
FORCEON
50 Ω
A.
CL includes probe and jig capacitance.
B.
The pulse generator has the following characteristics: PRR = 250 kbits/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤
10 ns.
Figure 4. Receiver Propagation Delay Times
Submit Documentation Feedback
9
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
PARAMETER MEASUREMENT INFORMATION (continued)
FORCEOFF
50 Ω
A.
CL includes probe and jig capacitance.
B.
The pulse generator has the following characteristics: PRR = 250 kbits/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤
10 ns.
C.
tPLZ and tPHZ are the same as tdis.
D.
tPZL and tPZH are the same as ten.
Figure 5. Receiver Enable and Disable Times
10
Submit Documentation Feedback
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
PARAMETER MEASUREMENT INFORMATION (continued)
2.7 V
2.7 V
0V
Receiver
Input
50 Ω
INV
Output
AutoPowerdown
tinvalid
tvalid
50% V CC
50% V CC
DIN
0V
ten
V+
≈V+
0.3 V
VCC
0V
0.3 V
Supply
Voltages
FORCEOFF
-3 V
VCC
INV
CL = 30 pF
(see Note A)
FORCEON
0V
-2.7 V
-2.7 V
ROUT
Generator
(see Note B)
3V
DOUT
V-
≈V-
Valid RS-232 Level, INV High
2.7 V
Indeterminate
0.3 V
0V
If Signal Remains Within This Region
for More Than 30 µs, INV is Low (see Note C)
-0.3 V
Indeterminate
-2.7 V
Valid RS-232 Level, INV High
A.
CL includes probe and jig capacitance.
B.
The pulse generator has the following characteristics: PRR = 250 kbits/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤
10 ns.
Figure 6. INV Propagation Delay Times and Supply Enabling Times
Submit Documentation Feedback
11
TRSF23243
3-V TO 5.5-V DUAL RS-232 PORT
www.ti.com
SLLS855 – AUGUST 2007
APPLICATION INFORMATION
C1+
12
+
C2
11
-
38
V-
GND
C1-
RIN2
RIN3
RIN4
RIN5
DOUT1
RS-232 Outputs
VCC
+
RIN1
RS-232 Inputs
C2-
DOUT2
5 (20)
37
14
13, 34
+ (see Note A)
C3
+
C1
+ CBYPASS
- = 0.1 µF
35
39
FORCEON
4 (21)
AutoPowerdown
C4
-
V+
C2+
36
3 (22)
2 (23)
10 (15)
FORCEOFF
1 (24)
6 (19)
9 (16)
43 (30)
8 (17)
44 (29)
INV
ROUT2
ROUT1
5 kΩ
DOUT3
7 (18)
45 (28)
ROUT2
5 kΩ
DIN3
42 (31)
Logic Outputs
46 (27)
ROUT3
5 kΩ
Logic Inputs
DIN2
41 (32)
47 (26)
ROUT4
5 kΩ
DIN1
40 (33)
48 (25)
ROUT5
5 kΩ
VCC vs CAPACITOR VALUES
VCC
C1
C2, C3, and C4
3.3 V ± 0.3 V
5 V ± 0.5 V
3 V to 5.5 V
0.22 µF
0.047 µF
0.22 µF
0.22 µF
0.33 µF
1 µF
A.
C3 can be connected to VCC or GND.
B.
Resistor values shown are nominal.
C.
Numbers in parentheses are for B section.
Figure 7. Typical Operating Circuit and Capacitor Values
12
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
28-Aug-2010
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
TRSF23243CDGGR
ACTIVE
TSSOP
DGG
48
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
TRSF23243CDGGRG4
ACTIVE
TSSOP
DGG
48
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
TRSF23243CDLR
ACTIVE
SSOP
DL
48
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
TRSF23243CDLRG4
ACTIVE
SSOP
DL
48
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TRSF23243CDGGR
TSSOP
DGG
48
2000
330.0
24.4
8.6
15.8
1.8
12.0
24.0
Q1
TRSF23243CDLR
SSOP
DL
48
1000
330.0
32.4
11.35
16.2
3.1
16.0
32.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TRSF23243CDGGR
TSSOP
DGG
48
2000
367.0
367.0
45.0
TRSF23243CDLR
SSOP
DL
48
1000
367.0
367.0
55.0
Pack Materials-Page 2
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUARY 1998
DGG (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0,27
0,17
0,50
48
0,08 M
25
6,20
6,00
8,30
7,90
0,15 NOM
Gage Plane
1
0,25
24
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
48
56
64
A MAX
12,60
14,10
17,10
A MIN
12,40
13,90
16,90
DIM
4040078 / F 12/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated