Optical Camera Link Cable Assembly for Full Configuration (8bit - 8tap) FOCLF Series FEATURES Full configuration (8bit - 8tap) used with FOCLB series cable assembly (Note 1) Enables 100 m transmission without extender/repeater by transmitting image signals over optical fiber High flex cycles cable available as an option Note 1: This cable alone or two pcs of this cable cannot operate as Full configuration. GENERAL SPECIFICATIONS Parameters Descriptions Configuration Full Configuration (8bit - 8tap) Camera Clock Rate 20 ~ 85 MHz Transmission Length Max 100 m (Note 2) Cable Type Standard / High Flex Cycles Electrical Connector MDR Straight Plug / SDR Straight Plug / SDR Right-angled Plug (Camera-side only) Power Supply Voltage +12 V DC Power Supply Type PoCL Power Supply (Note 3) / External Power Supply Flex Life (Slide Bending) Under testing for high flex cycles cable Power Consumption 1.80 W (Typ.) Note 2: Maximum transmission distance for PoCL is 30 m. Please consult us for the detail. Note 3: PoCL type cable can be used for Full side port of Camera and Grabber board if both Full side port of them support PoCL power supply. Please consult us for the detail. SYSTEM CONFIGURATION EXAMPLES Full Configuration (non-PoCL) +12 V Power Supply Base-side Optical Camera Link Cable Assembly FOCLB Series (Soled separately) +12 V Power Supply Full-side Optical Camera Link Cable Assembly FOCLF Series (This product) Non-PoCL type Full Configuration Camera Power Supply to Camera Full Configuration Grabber Board Full Configuration (Example for Base-side connector of Camera being PoCL) Base-side Optical Camera Link Cable Assembly FOCLB Series (Soled separately) +12 V Power Supply Full-side Optical Camera Link Cable Assembly FOCLF Series (This product) PoCL type Full Configuration Camera Full Configuration Grabber Board CONNECTOR DIMENSIONS MDR Straight Plug SDR Straight Plug [unit: mm] BLOCK DIAGRAM (Example for PoCL Base cable and non-PoCL Full cable) X Image Signals P/S X Clock FOCLB Series E/O Grabber-board Side Connector O/E Optical Fiber MCU Serial Communication Camera Ctrl (CC1~4) +12 V (PoCL) GND S/P X Image Signals X Clock MCU Serial Communication Camera Ctrl (CC1~4) +12 V (PoCL) GND Optical Fiber & Metal Hybrid Cable Base-side Connector Base-side Connector Camera Side Connector Y Image Signals P/S O/E E/O Optical Fiber #1 Optical Fiber & Metal Hybrid Cable Z Image Signals P/S E/O O/E Optical Fiber #2 Y Image Signals Y Clock MCU MCU Y Clock S/P S/P Z Image Signals Z Clock Z Clock GND GND GND Full-side Connector Full-side Connector FOCLF Series +12 V (External Power Supply) ORDERING INFORMATION For full configuration application, both FOCLF cable and FOCLB cable are needed. e.g.) Base-side: FOCLBN-20S-MPS-MP Full-side: FOCLFN-20S-MPS-MP [Length] 01, 03, 05, 07, 10, 15, 20, 30, 40, 50, 60, 70, 80, 90, A0 (=100m) [Camera-side connector] MDR: M SDR: S Straight: S Right-angle (camera-side only): R [Right-angle Orientation] [Configuration] 14-26 pin side (Down): D 1-13 pin side (Up): U Full: F FOCLFN-20S-SPRD3-MP FOCLFP-20D-MPS -SP [Power Supply] Non-PoCL: N PoCL (Note 4): P Plug (male): P [Cable] Standard: S High Flex Cycles: D For N, select side where wires for power supply are fitted. Plug (male): P MDR: M SDR: S [Grabber-side connector] Standard (Wires on Grabber-side): blank Wires on Camera-side: 3 Note 4: PoCL type cable can be used for Full side port of Camera and Grabber board if both Full side port of them support PoCL power supply. Fujikura Ltd. Datacom Products Department 1-5-1, Kiba, Koto-ku, Tokyo 135-8512, Japan Phone: +81-3-5606-1473 Fax: +81-3-5606-1598 E-mail: www.fujikura.co.jp June, 2013 CC93-11-13-0053(1) Contents are subjected to change without notice. Copyright © 2013 Fujikura Ltd. All right reserved.