Optical Camera Link Cable Assembly for Base/Medium Configurations FOCLB Series FEATURES Breaks limit of standard Camera Link transmission distance and enables 100 m transmission without repeater/extender Same electrical interface connectors as metal cables Includes Optical-Electrical conversion functions inside of electrical connectors at both ends Optical fiber/metal hybrid cable enables PoCL and camera control Flexible and easy to use GENERAL SPECIFICATIONS Parameters Descriptions Configuration Base Configuration (1~3 tap), Medium Configuration (3~6 tap) Camera Clock Rate 20 ~ 85 MHz Transmission Length Max 100 m. For longer distance, please contact us. (Note 1) Cable Type Standard / High Flex Cycles Electrical Connector MDR Straight Plug / SDR Straight Plug / SDR Right-angled Plug (Camera-side only) Power Supply Voltage +12 V DC Power Supply Type PoCL Power Supply (Note 2) / External Power Supply Flex Life (Slide Bending) More than 10M cycles (R=50 mm) for high flex cycles cable only. Power Consumption 0.88 W (Typ.) Note 1: Maximum transmission distance for PoCL is 30 m. Please consult us for the detail. Note 2: PoCL type cable can be used for Medium side port of Camera and Grabber board if both Medium side port of them support PoCL power supply. Please consult us for the detail. SYSTEM CONFIGURATION EXAMPLES Base Configuration (Non-PoCL) +12 V Power Supply Base Cable FOCLB Series Non-PoCL Camera Power Supply for Camera Grabber Board for Base Base Configuration (PoCL) Base Cable FOCLB Series PoCL Camera Grabber Board for PoCL Medium Configuration (Non-PoCL) +12 V Power Supply グラバボード Base Cable FOCLB Series Medium Config. Camera Base Cable FOCLB Series Power Supply for Camera Grabber Board for Medium (Non-PoCL) CONNECTOR DIMENSIONS MDR Straight Plug SDR Straight Plug [unit: mm] BLOCK DIAGRAM (Example for Non-PoCL) Grabber-board Side Connector Camera Side Connector X Image Signals E/O P/S X Clock O/E Optical Fiber MCU Serial Communication Camera Ctrl (CC1~4) S/P X Image Signals X Clock MCU Serial Communication Camera Ctrl (CC1~4) Optical Fiber & Metal Hybrid Cable GND GND GND Test Method Slide Bending (w/ Cable Track) Test Conditions Stroke Length: 350 mm Bend Radius: 50 mm Traveling Speed: 72 times/min D Optical Loss (dB) DUT High Flex Cycles Cable (FOCLB Series) 3.0 2.0 1.0 0.0 -1.0 -2.0 -3.0 Resistance (W) FLEX TEST RESULTS (High Flex Cycles cable) 8.0 Upper Limit Optical Fiber (Change of Optical Loss, Initial=0dB) Lower Limit 0 Measured Parameters Change of optical loss and resistance +12 V (External Power Supply) 6.0 1,000 2,000 3,000 4,000 5,000 x 10,000 Cycles 6,000 Metal Wire (Control Signal) 4.0 Metal Wire (Power Supply) 2.0 0.0 0 1,000 2,000 3,000 4,000 x 10,000 Cycles 5,000 6,000 ORDERING INFORMATION [Length] 01, 03, 05, 07, 10, 15, 20, 30, 40, 50, 60, 70, 80, 90, A0 (=100m) [Camera-side connector] MDR: M SDR: S Straight: S Right-angle (camera-side only): R [Right-angle Orientation] [Configuration] 14-26 pin side (Down): D 1-13 pin side (Up): U Base: B FOCLBN－20S－SPRD3－MP FOCLBP－20D－MPS －SP [Power Supply] Non-PoCL: N PoCL (Note 3): P Plug (male): P [Cable] Standard: S High Flex Cycles: D For N, select side where wires for power supply are fitted. Plug (male): P MDR: M SDR: S [Grabber-side Connector] Standard (Wires on Grabber-side): blank Wires on Camera-side: 3 Note 3: PoCL type cable can be used for Medium side port of Camera and Grabber board, if both Medium side port of them support PoCL power supply. Fujikura Ltd. Datacom Products Department 1-5-1, Kiba, Koto-ku, Tokyo 135-8512, Japan Phone: +81-3-5606-1473 Fax: +81-3-5606-1598 E-mail: www.fujikura.co.jp June, 2013 CC93-11-13-0054(1) Contents are subjected to change without notice. Copyright © 2013 Fujikura Ltd. All right reserved.