LTC3521 1A Buck-Boost DC/DC and Dual 600mA Buck DC/DC Converters Features Description Three High Efficiency DC/DC Converters: Buck-Boost (VOUT: 1.8V to 5.25V, IOUT: 1A) Dual Buck (VOUT: 0.6V to VIN, IOUT: 600mA) n 1.8V to 5.5V Input Voltage Range n Pin-Selectable Burst Mode® Operation n 30µA Total Quiescent Current in Burst Mode Operation n Independent Power Good Indicator Outputs n Integrated Soft-Start n Thermal and Overcurrent Protection n<2µA Current in Shutdown n Small 4mm × 4mm QFN and Thermally Enhanced TSSOP Packages The LTC®3521 combines a 1A buck-boost DC/DC converter and dual 600mA synchronous buck DC/DC converters. The 1.1MHz switching frequency minimizes the solution footprint while maintaining high efficiency. All three converters feature soft-start and internal compensation to minimize the solution footprint and simplify the design process. n The buck converters are current mode controlled and utilize an internal synchronous rectifier to improve efficiency. The buck converters support 100% duty cycle operation to extend battery life. If the PWM pin is held low, the buck converters automatically transition from Burst Mode operation to PWM mode at high loads. With the PWM pin held high, the buck converters remain in low noise, 1.1MHz PWM mode. Applications n n n n n The buck-boost converter features continuous conduction operation to maximize efficiency and minimize noise. At light loads, the buck-boost converter can be operated in Burst Mode operation to improve efficiency and reduce no-load standby current. Bar Code Readers Medical Instruments Handy Terminals PDAs, Handheld PCs GPS Receivers L, LT, LTC, LTM, Linear Technology, Burst Mode and the Linear logo are registered trademarks and PowerPath is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U. S. Patents, including 6404251, 6166527. The LTC3521 provides a <2μA shutdown mode, overtemperature shutdown and current limit protection on all converters. The LTC3521 is available in a 24-pin 0.75mm × 4mm × 4mm QFN package, and a 20-pin thermally enhanced TSSOP package. Typical Application VOUT1 3.3V 800mA (1A, VIN > 3.0V) + Li-Ion 4.7µF 4.7µH PVIN1 VIN PVIN2 SW2 SW1A 4.7µH 137k SW1B FB2 VOUT1 22µF 1.0M 221k OFF BURST 68.1k LTC3521 ON PWM VOUT2 1.8V 10µF 600mA FB1 SW3 SHDN1 FB3 SHDN2 SHDN3 PGOOD1 PWM PGOOD2 PGND1A PGOOD3 PGND1B GND PGND2 4.7µH 100k VOUT3 1.2V 10µF 600mA 100k 3521 TA01a EFFICIENCY (%) VIN 2.4V TO 4.2V 100 98 96 94 92 90 88 86 84 82 80 78 76 74 72 70 2.4 Efficiency vs VIN VOUT1 = 3.3V IOUT = 500mA VOUT3 = 1.2V IOUT = 200mA VOUT2 = 1.8V IOUT = 200mA 4.4 3.4 VIN (V) 5.4 3521 TA01b 3521fb For more information www.linear.com/LTC3521 1 LTC3521 Absolute Maximum Ratings (Note 1) PVIN1, PVIN2, VIN Voltage.............................. –0.3V to 6V SW1A, SW1B, SW2, SW3 Voltage DC............................................................. –0.3V to 6V Pulsed < 100ns.............................................–1V to 7V Voltage, All Other Pins.................................. –0.3V to 6V Operating Junction Temperature Range (Notes 2, 5)............................................. –40°C to 125°C Storage Temperature Range................... –65°C to 150°C Pin Configuration SW2 PGND1A 20 PVIN2 24 23 22 21 20 19 FB2 2 19 SW2 SHDN2 3 18 PGND2 PGOOD3 4 17 SW3 PGOOD3 2 PGOOD2 5 16 VOUT1 PGOOD2 3 PGOOD1 6 15 SW1A PGOOD1 4 VIN 7 14 SW1B VIN 5 GND 8 13 PVIN1 GND 6 PWM 9 12 SHDN1 FB1 10 11 SHDN3 SHDN2 1 17 SW3 16 VOUT1 25 PGND1A 15 SW1A 14 SW1B PGND1B 9 10 11 12 PVIN1 8 SHDN1 7 FB1 13 NC SHDN3 FE PACKAGE 20-LEAD PLASTIC TSSOP TJMAX = 150°C, θJA = 40°C/W (NOTE 4) UNDERSIDE METAL INTERNALLY CONNECTED TO V – (PCB CONNECTION OPTIONAL) EXPOSED PAD (PIN 21) IS PGND1A AND MUST BE SOLDERED TO PCB GROUND 18 PGND2 PWM 21 PGND1A NC 1 FB3 FB3 FB2 PVIN2 TOP VIEW TOP VIEW UF PACKAGE 24-LEAD (4mm × 4mm) PLASTIC QFN TJMAX = 125°C, θJA = 37°C/W EXPOSED PAD (PIN 25) IS PGND1A AND MUST BE SOLDERED TO PCB GROUND Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3521EFE#PBF LTC3521EFE#TRPBF LTC3521FE 20-Lead Plastic TSSOP –40°C to 125°C LTC3521IFE#PBF LTC3521IFE#TRPBF LTC3521FE 20-Lead Plastic TSSOP –40°C to 125°C LTC3521EUF#PBF LTC3521EUF#TRPBF 3521 24-Lead (4mm × 4mm) Plastic QFN –40°C to 125°C LTC3521IUF#PBF LTC3521IUF#TRPBF 3521 24-Lead (4mm × 4mm) Plastic QFN –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 2 3521fb For more information www.linear.com/LTC3521 LTC3521 Electrical Characteristics The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C (Note 2). VIN, PVIN1, PVIN2 = 3.6V, VOUT1 = 3.3V, unless otherwise noted. PARAMETER CONDITIONS MIN Input Voltage l Quiescent Current—Shutdown VSHDN1 = VSHDN2 = VSHDN3 = 0V (Note 6) Burst Mode Quiescent Current VFB1 = 0.66V, VFB2 = 0.66V, VFB3 = 0.66V, VPWM = 0V TYP 1.8 0.01 l MAX 5.5 V 2 µA 30 Oscillator Frequency l 0.85 SHDN1, SHDN2, SHDN3, PWM Input High Voltage l 1.4 SHDN1, SHDN2, SHDN3, PWM Input Low Voltage l 1.1 UNITS µA 1.35 MHz V 0.4 V Power Good Outputs Low Voltage IPGOOD1 = IPGOOD2 = IPGOOD3 = 1mA 0.1 0.2 V Power Good Outputs Leakage Current VPGOOD1 = VPGOOD2 = VPGOOD3 = 5.5V 0.1 10 µA Buck Converters PMOS Switch Resistance 0.205 Ω NMOS Switch Resistance 0.170 Ω NMOS Switch Leakage Current VSW2 = VSW3 = 5.5V, VIN = 5.5V 0.1 PMOS Switch Leakage Current VSW2 = VSW3 = 0V, VIN = 5.5V Feedback Voltage (Note 4) Feedback Input Current VFB2 = VFB3 = 0.6V PMOS Current Limit (Note 3) l 750 Maximum Duty Cycle VFB2 = VFB3 = 0.55V l 100 Minimum Duty Cycle VFB2 = VFB3 = 0.66V l PGOOD Threshold VFB2,3 Falling Power Good Hysteresis VFB2,3 Returning Good l 0.585 –12 5 µA 0.1 10 µA 0.6 0.612 V 1 50 nA 1050 mA % –9 0 % –6 % 2 % Buck-Boost Converter Output Voltage l 1.8 5.25 V PMOS Switch Resistance 0.110 Ω NMOS Switch Resistance 0.085 Ω NMOS Switch Leakage Current VSW1A = VSW1B = 5.5V, VIN = 5.5V 0.1 5 µA PMOS Switch Leakage Current VSW1A = VSW1B = 0V, VIN = 5.5V 0.1 10 µA Feedback Voltage (Note 4) l 0.585 0.6 0.612 V 1 50 nA l 1.65 2.1 A 375 mA 94 % Feedback Input Current VFB1 = 0.6V Average Current Limit (Note 3) Reverse Current Limit (Note 3) Maximum Duty Cycle VFB1 = 0.55V l Minimum Duty Cycle VFB1 = 0.66V l PGOOD Threshold VFB1 Falling Power Good Hysteresis VFB1 Returning Good Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3521 is tested under pulsed load conditions such that TJ ≈ TA. The LTC3521E is guaranteed to meet performance specifica- 85 0 –12 –9 3 –6 % % % tions from 0°C to 85°C. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3521I is guaranteed over the full –40°C to 125°C operating junction temperature range. The maximum ambient temperature is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. 3521fb For more information www.linear.com/LTC3521 3 LTC3521 Electrical Characteristics Note 3: Current measurements are performed when the LTC3521 is not switching. The current limit values in operation will be somewhat higher due to the propagation delay of the comparators. Note 4: The LTC3521 is tested in a proprietary test mode that connects each FB pin to the output of the respective error amplifier. Note 5: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. Note 6: Shutdown current is measured on the VIN pin and does not include PMOS switch leakage. Typical Performance Characteristics Buck-Boost Efficiency vs Load Current, Li-Ion to 3.3V 100 VIN = 2.7V VIN = 4.2V 90 Buck Efficiency vs Load Current, Li-Ion to 2.5V 140 PWM MODE 100 80 50 Burst Mode 40 OPERATION 60 30 40 20 0 0.1 1 100 10 LOAD CURRENT (mA) 70 VIN = 2.7V VIN = 4.2V EFFICIENCY (%) 60 60 40 Burst Mode POWER LOSS 20 0 0.1 4 40 20 10 1 100 10 LOAD CURRENT (mA) 0 1000 100 10 LOAD CURRENT (mA) 3521 G02 60 50 120 80 30 20 Buck Burst Mode Current Threshold vs VIN 100 50 1 3521 G01 140 PWM MODE 40 Burst Mode POWER LOSS 0 0.1 0 1000 POWER LOSS (mW) Burst Mode OPERATION 60 40 10 LOAD CURRENT (mA) 90 80 50 20 0 1000 120 100 60 Buck Efficiency vs Load Current, Li-Ion to 1.8V 100 Burst Mode OPERATION 30 20 Burst Mode POWER LOSS 10 EFFICIENCY (%) 60 140 PWM MODE POWER LOSS (mW) 70 POWER LOSS (mW) EFFICIENCY (%) 80 100 70 VIN = 3.6V VIN = 4.2V 90 120 80 80 TA = 25°C, unless otherwise noted. VOUT = 1.2V 40 30 20 10 0 1.5 VOUT = 1.8V VOUT = 2.5V 2 3521 G03 2.5 3 3.5 VIN (V) 4 4.5 5 5.5 3521 G04 3521fb For more information www.linear.com/LTC3521 LTC3521 Typical Performance Characteristics Buck-Boost Switches RDS(ON) vs Temperature Buck Switches RDS(ON) vs Temperature 350 160 VIN = 3.6V 140 VOUT1 = 3.3V 0.8 NMOS (SWITCHES B AND C) 60 0.6 PMOS CHANGE FROM 25°C (%) RDS(ON) (mΩ) NMOS 200 150 100 40 50 20 0 –40 –20 0 20 40 60 80 100 120 0 20 40 60 80 100 120 CHANGE IN FEEDBACK VOLTAGE FROM 25°C (%) 2.0 CHANGE FROM VIN = 3.6V (%) 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 3.3 3.8 4.3 4.8 5.3 0.1 0 –0.1 –0.2 –0.3 –0.4 –0.5 –40 –20 0 20 40 60 80 100 120 29 27 3.3 3.8 0 –0.1 –0.2 –0.3 –0.4 –0.5 –50 Buck-Boost Maximum Load Current vs VIN, Burst Mode Operation –25 0 4.3 4.8 5.3 VIN (V) VOUT = 3V 50 75 100 60 VOUT = 5V 50 40 30 20 0 1.8 125 3521 G10 L = 4.7µH 1300 70 VOUT = 3.3V 1100 900 VOUT = 5V 700 500 300 2.3 2.8 3.3 3.8 4.3 4.8 5.3 VIN (V) 3521 G11 25 Buck-Boost Maximum Load Current vs VIN, PWM Mode 1500 80 10 2.8 0.1 TEMPERATURE (°C) LOAD CURRENT (mA) MAXIMUM LOAD CURRENT (mA) QUIESCENT CURRENT (µA) 90 ALL THREE CONVERTERS ENABLED 2.3 0.2 3521 G09 Burst Mode Quiescent Current vs VIN 31 90 110 3521 G07 TEMPERATURE (°C) 3521 G08 25 1.8 –0.6 Buck Feedback Voltage vs Temperature 0.2 VIN (V) 33 –0.4 Buck-Boost Feedback Voltage vs Temperature Switching Frequency vs VIN 2.8 0 –0.2 3521 G06 3521 G05 2.3 0.2 –1.0 –50 –30 –10 10 30 50 70 TEMPERATURE (°C) TEMPERATURE (°C) TEMPERATURE (°C) –2.0 1.8 0.4 –0.8 0 –40 –20 CHANGE IN FEEDBACK VOLTAGE FROM 25°C (%) RDS(ON) (mΩ) 1.0 VIN = 3.6V 250 100 80 Switching Frequency vs Temperature 300 PMOS (SWITCHES A AND D) 120 TA = 25°C, unless otherwise noted. 100 1.8 2.3 2.8 3.3 3.8 VIN (V) 4.3 4.8 5.3 3521 G13 3521 G12 3521fb For more information www.linear.com/LTC3521 5 LTC3521 Typical Performance Characteristics QUIESCENT CURRENT (µA) 60 TA = 25°C, unless otherwise noted. Buck-Boost Load Step, 0mA to 750mA No Load Quiescent Current vs VIN VOUT 100mV/DIV 55 VIN = 3.6V, VOUT = 3.3V L = 4.7µH COUT = 22µF 50 INDUCTOR CURRENT 500mA/DIV 45 3521 G15 100µs/DIV 40 1.8 2.3 2.8 3.3 3.8 4.3 4.8 VIN (V) Buck-Boost Burst Mode Operation to PWM Transition INDUCTOR CURRENT 200mA/DIV VOUT 20mV/DIV VOUT 100mV/DIV VOUT 100mV/DIV INDUCTOR CURRENT 200mA/DIV INDUCTOR CURRENT 200mA/DIV Buck Current Limit vs Temperature 3350 1150 2050 2000 CURRENT LIMIT (mA) 1100 2100 CURRENT LIMIT (mA) CURRENT LIMIT (mA) 3521 G18 100µs/DIV L = 4.7µH COUT = 10µF VIN = 3.6V VOUT = 1.8V Buck-Boost Peak Current Limit vs Temperature 2150 3300 3250 1050 1000 950 –25 0 25 50 75 TEMPERATURE (°C) 6 3521 G17 100µs/DIV L = 4.7µH COUT = 10µF VIN = 3.6V VOUT = 1.8V Buck-Boost Current Limit vs Temperature 1950 –50 Buck Load Step, Burst Mode, 10mA to 400mA Buck Load Step, PWM Mode, 10mA to 400mA 3521 G16 50µs/DIV L = 4.7µH COUT = 22µF VIN = 3.6V VOUT = 3.3V 5.3 3521 G14 100 125 3521 G19 3200 –50 –25 0 25 50 75 TEMPERATURE (°C) 100 125 3521 G20 900 –50 –25 0 25 50 75 TEMPERATURE (°C) 100 125 3521 G21 3521fb For more information www.linear.com/LTC3521 LTC3521 Pin Functions (FE/UF Packages) FB3 (Pin 1/Pin 23): Feedback Voltage for the Buck Converter Derived from a Resistor Divider Connected to the Buck VOUT3 Output Voltage. The buck output voltage is given by the following equation, where R1 is a resistor between FB3 and ground, and R2 is a resistor between FB3 and the buck output voltage: ⎛ R2 ⎞ VOUT3 = 0.6V ⎜1+ ⎟ ⎝ R1 ⎠ FB2 (Pin 2/Pin 24): Feedback Voltage for the Buck Converter Derived from a Resistor Divider Connected to the Buck VOUT2 Output Voltage. The buck output voltage is given by the following equation, where R1 is a resistor between FB2 and ground, and R2 is a resistor between FB2 and the buck output voltage: ⎛ R2 ⎞ VOUT2 = 0.6V ⎜1+ ⎟ ⎝ R1 ⎠ SHDN2 (Pin 3/Pin 1): Forcing this pin above 1.4V enables the buck converter output at SW2. Forcing this pin below 0.4V disables the buck converter. This pin cannot be left floating. PGOOD3 (Pin 4/Pin 2): This pin is an open-drain output which pulls low under any of the following conditions: VOUT3 buck output voltage is out of regulation, the part is in overtemperature shutdown, the part is in undervoltage lockout, or the SHDN3 pin is pulled low. PGOOD2 (Pin 5/Pin 3): This pin is an open-drain output which pulls low under any of the following conditions: VOUT2 buck output voltage is out of regulation, the part is in overtemperature shutdown, the part is in undervoltage lockout, or the SHDN2 pin is pulled low. PGOOD1 (Pin 6/Pin 4): This pin is an open-drain output which pulls low under any of the following conditions: VOUT1 buck-boost output voltage is out of regulation, the part is in overtemperature shutdown, the part is in undervoltage lockout, the buck-boost converter is in current limit, or the SHDN1 pin is pulled low. See the Operation section of this data sheet for details on the functionality of this pin in PWM mode. VIN (Pin 7/Pin 5): Low Current Power Supply Connection Used to Power the Internal Circuitry of the LTC3521. This pin should be bypassed by a 4.7µF, or larger, ceramic capacitor. The bypass capacitor should be placed as close to the pin as possible and should have a short return path to ground. Pins VIN , PVIN1, and PVIN2 must be connected together in the application circuit. GND (Pin 8/Pin 6): Small Signal Ground. This pin is used as a ground reference for the internal circuitry of the LTC3521. PWM (Pin 9/Pin 7): Logic Input Used to Choose Between Burst Mode Operation and PWM Mode for All Three Converters. This pin cannot be left floating. PWM = Low: Burst Mode operation is enabled on all three converters. The buck converters will operate in Burst Mode operation at light current but will automatically transition to PWM operation at high currents. The buck converters can supply maximum output current (600mA) in this mode. The buck-boost converter will operate in variable frequency mode and can only supply a reduced load current (typically 50mA). PWM = High: All three converters are forced into PWM mode operation. The buck converters will remain at constant-frequency operation until their minimum ontime is reached. The buck-boost converter will remain in PWM mode at all load currents. FB1 (Pin 10/Pin 8): Feedback Voltage for the Buck-Boost Converter Derived from a Resistor Divider on the BuckBoost Output Voltage. The buck-boost output voltage is given by the following equation, where R1 is a resistor between FB1 and ground, and R2 is a resistor between FB1 and the buck output voltage: ⎛ R2 ⎞ VOUT1 = 0.6V ⎜1+ ⎟ ⎝ R1 ⎠ SHDN3 (Pin 11/Pin 9): Forcing this pin above 1.4V enables the buck converter output at SW3. Forcing this pin below 0.4V disables the buck converter. This pin cannot be left floating. SHDN1 (Pin 12/Pin 10): Forcing this pin above 1.4V enables the buck-boost converter. Forcing this pin below 0.4V disables the buck-boost converter. This pin cannot be left floating. 3521fb For more information www.linear.com/LTC3521 7 LTC3521 Pin Functions (FE/UF Packages) PVIN1 (Pin 13/Pin 11): High current power supply connection used to supply switch A of the buck-boost converter. This pin should be bypassed by a 4.7µF, or larger, ceramic cap. The bypass capacitor should be placed as close to the pin as possible and should have a short return path to ground. Pins VIN, PVIN1, and PVIN2 must be connected together in the application circuit. NC (Pin 13, UF Package Only): No Internal Connection. SW1B (Pin 14/Pin 14): Buck-Boost Switch Node. This pin must be connected to one side of the buck-boost inductor. SW1A (Pin 15/Pin 15): Buck-Boost Switch Node. This pin must be connected to one side of the buck-boost inductor. VOUT1 (Pin 16/Pin 16): Buck-Boost Output Voltage Node. This pin should be connected to a low ESR ceramic capacitor. The capacitor should be placed as close to the IC as possible and should have a short return to ground. SW3 (Pin 17/Pin 17): Buck converter Switch Node. This pin must be connected to the opposite side of the inductor connected to VOUT3. 8 PGND2 (Pin 18/Pin 18): High Current Ground Connection for Both Buck Converters. The PCB trace connecting this pin to ground should be made as short and wide as possible. SW2 (Pin 19/Pin 20): Buck Converter Switch Node. This pin must be connected to the opposite side of the inductor connected to VOUT2. NC (Pin 19, UF Package Only): No Internal Connection. PVIN2 (Pin 20/Pin 22): High Current Power Supply Connection Used to Supply the Buck Converter Power Switches. This pin should be bypassed by a 10µF or larger ceramic cap. The bypass capacitor should be placed as close to the pin as possible and should have a short return path to ground. Pins VIN, PVIN1, and PVIN2 must be connected together in the application circuit. PGND1A (Exposed Pad Pin 21/Pin 21, Exposed Pad Pin 25): High Current Ground Connection for the BuckBoost Switch B. The PCB trace connecting this pin to ground should be made as short and wide as possible. PGND1B (Pin 12, UF Package Only): High Current Ground Connection for the Buck-Boost Switch C. The PCB trace connecting this pin to ground should be made as short and wide as possible. 3521fb For more information www.linear.com/LTC3521 LTC3521 11 (UF Package) 15 PVIN1 14 SW1A 16 SW1B VOUT1 D A INTERNAL VCC 5 B VIN C + – REVERSE ILIMIT 0.375A IZERO 0A + – 22 PGOOD1 + – PWM FB1 0.6V SOFT-START RAMP SHDN1 SHDN3 SHDN2 PVIN2 PVIN2 4 PVOUT BUCK-BOOST PWM LOGIC GATE DRIVES 1 – 2.1A PGND1A PGND1B 7 FILTER FORWARD + ILIMIT 0.546V + + – Block Diagram PVIN2 OSCILLATOR 8 10 9 UVLO SW2 GATE DRIVES PGND2 0A + – BUCK PWM LOGIC BUCK PWM LOGIC ZERO CROSSING 1.05A + – ILIMIT 0.60V –gm + + 17 PGND2 0A 1.05A + SLOPE COMPENSATION + – gm + – 1.2V 0.6V SOFT-START RAMP PGOOD2 + – 3 + – ILIMIT SLOPE COMPENSATION FB2 + – ZERO CROSSING + 24 SW3 GATE DRIVES 0.546V 0.25V + + – 20 FB3 0.60V 23 SOFT-START RAMP BANDGAP REFERENCE AND OT SHUTDOWN 0.546V 0.546V GND PGND1A PGND1B PGND2 6 21 12 18 – + PGOOD3 2 3521 BD 3521fb For more information www.linear.com/LTC3521 9 LTC3521 Operation The LTC3521 combines dual synchronous buck DC/DC converters and a 4-switch buck-boost DC/DC converter in a 4mm × 4mm QFN package and a 20-pin thermally enhanced TSSOP package. The buck-boost converter utilizes a proprietary switching algorithm which allows its output voltage to be regulated above, below or equal to the input voltage. The buck converters provide a high efficiency lower voltage output and support 100% duty cycle operation to extend battery life. In Burst Mode operation, the total quiescent current for the LTC3521 is reduced to 30μA. All three converters are synchronized to the same internal 1.1MHz oscillator. Buck Converter Operation PWM Mode Operation When the PWM pin is held high, the LTC3521 buck converters use a constant-frequency, current mode control architecture. Both the main (P-channel MOSFET) and synchronous rectifier (N-channel MOSFET) switches are internal. At the start of each oscillator cycle, the P-channel switch is turned on and remains on until the current waveform with superimposed slope compensation ramp exceeds the error amplifier output. At this point, the synchronous rectifier is turned on and remains on until the inductor current falls to zero or a new switching cycle is initiated. As a result, the buck converters operate with discontinuous inductor current at light loads, which improves efficiency. At extremely light loads, the minimum on-time of the main switch will be reached and the buck converters will begin turning off for multiple cycles in order to maintain regulation. Burst Mode Operation When the PWM pin is forced low, the buck converters will automatically transition between Burst Mode operation at sufficiently light loads (below approximately 15mA) and PWM mode at heavier loads. Burst Mode entry is determined by the peak inductor current. Therefore, the load current at which Burst Mode operation will be entered depends on the input voltage, the output voltage and the inductor value. Typical curves for Burst Mode entry threshold are provided in the Typical Performance Characteristics section of this data sheet. In dropout and near dropout conditions, Burst Mode operation is disabled. 10 Dropout Operation As the input voltage decreases to a value approaching the output regulation voltage, the duty cycle increases toward the maximum on-time. Further reduction of the supply voltage will force the main switch to remain on for more than one cycle until 100% duty cycle operation is reached where the main switch remains on continuously. In this dropout state, the output will be determined by the input voltage less the resistive voltage drop across the main switch and series resistance of the inductor. Slope Compensation Current mode control requires the use of slope compensation to prevent subharmonic oscillations in the inductor current at high duty cycle operation. This is accomplished internally on the LTC3521 through the addition of a compensating ramp to the current sense signal. In some current mode ICs, current limiting is performed by clamping the error amplifier voltage to a fixed maximum. This leads to a reduced output current capability at low step-down ratios. In contrast, the LTC3521 performs current limiting prior to addition of the slope compensation ramp and therefore achieves a peak inductor current limit that is independent of duty cycle. Short-Circuit Protection When the output is shorted to ground, the error amplifier will saturate high and the P-channel MOSFET switch will turn on at the start of each cycle and remain on until the current limit trips. During this minimum on-time, the inductor current will increase rapidly and will decrease very slowly during the remainder of the period due to the very small reverse voltage produced by a hard output short. To eliminate the possibility of inductor current runaway in this situation, the buck converter switching frequency is reduced to 250kHz when the voltage on the buck FB pin falls below 0.25V. The buck soft-start circuit is reset when the buck FB pin falls below 0.25V to provide a smooth restart once the short-circuit condition at the output voltage is no longer present. Additionally, the PMOS current limit is decreased from 1050mA to 700mA when the voltage on the buck FB pin falls below 0.25V. 3521fb For more information www.linear.com/LTC3521 LTC3521 Operation Soft-Start Buck-Boost Converter Operation The buck converters have an internal voltage mode soft-start circuit with a nominal duration of 800μs. The converters remain in regulation during soft-start and will therefore respond to output load transients which occur during this time. In addition, the output voltage rise time has minimal dependency on the size of the output capacitor or load current. PWM Mode Operation When the PWM pin is held high, the LTC3521 buck-boost converter operates in a constant-frequency PWM mode with voltage mode control. A proprietary switching algorithm allows the converter to switch between buck, buckboost and boost modes without discontinuity in inductor current or loop characteristics. The switch topology for the buck-boost converter is shown in Figure 1. Error Amplifier and Compensation When the input voltage is significantly greater than the output voltage, the buck-boost converter operates in buck mode. Switch D turns on continuously and switch C remains off. Switches A and B are pulse width modulated to produce the required duty cycle to support the output regulation voltage. As the input voltage decreases, switch A remains on for a larger portion of the switching cycle. When the duty cycle reaches approximately 85%, the switch pair AC begins turning on for a small fraction of the switching period. As the input voltage decreases further, the AC switch pair remains on for longer durations and the duration of the BD phase decreases proportionally. As the input voltage drops below the output voltage, the AC phase will eventually increase to the point that there is no longer any BD phase. At this point, switch A remains on continuously while switch pair CD is pulse width modulated to obtain the desired output voltage. At this point, the converter is operating solely in boost mode. The LTC3521 buck converters utilize an internal transconductance error amplifier. Compensation of the feedback loop is performed internally to reduce the size of the application circuit and simplify the design process. The compensation network has been designed to allow use of a wide range of output capacitors while simultaneously ensuring rapid response to load transients. PGOOD Comparators The PGOOD2 and PGOOD3 pins are open-drain outputs which indicate the status of the buck converters. If the buck output voltage falls 9% below the regulation voltage, the respective PGOOD open-drain output will pull low. The output voltage must rise 2% above the falling threshold before the pull-down will turn off. In addition, there is a 60μs typical deglitching delay in the flag in order to prevent false trips due to voltage transients on load steps. The respective PGOOD output will also pull low during overtemperature shutdown, undervoltage lockout or if the respective buck converter SHDN pin is pulled low to indicate these fault conditions. This switching algorithm provides a seamless transition between operating modes and eliminates discontinuities in average inductor current, inductor current ripple and loop transfer function throughout all three operational L PVIN1 A SW1A B LTC3521 PGND1A SW1B D VOUT1 C PGND1B 3521 F01 Figure 1. Buck-Boost Switch Topology 3521fb For more information www.linear.com/LTC3521 11 LTC3521 Operation modes. These advantages result in increased efficiency and stability in comparison to the traditional 4-switch buck-boost converter. this case, the increased bandwidth created by decreasing R2 is used to counteract the reduced converter bandwidth caused by the large output capacitor. Error Amplifier and Compensation Current Limit Operation The buck-boost converter utilizes a voltage mode error amplifier with an internal compensation network as shown in Figure 2. The buck-boost converter has two current limit circuits. The primary current limit is an average current limit circuit which injects an amount of current into the feedback node which is proportional to the extent that the switch A current exceeds the current limit value. Due to the high gain of this loop, the injected current forces the error amplifier output to decrease until the average current through switch A decreases approximately to the current limit value. The average current limit utilizes the error amplifier in an active state and thereby provides a smooth recovery with little overshoot once the current limit fault condition is removed. Since the current limit is based on the average current through switch A, the peak inductor current in current limit will have a dependency on the duty cycle (i.e., on the input and output voltages in the overcurrent condition). LTC3521 PVOUT + – 0.6V FB1 VOUT R2 R1 GND 3521 F02 Figure 2. Buck-Boost Error Amplifier and Compensation Notice that resistor R2 of the external resistor divider network plays an integral role in determining the frequency response of the compensation network. The ratio of R2 to R1 must be set to program the desired output voltage but this still allows the value of R2 to be adjusted to optimize the transient response of the converter. Increasing the value of R2 generally leads to greater stability at the expense of reduced transient response speed. Increasing the value of R2 can yield substantial transient response improvement in cases where the phase margin has been reduced due to the use of a small value output capacitor or a large inductance (particularly with large boost step-up ratios). Conversely, decreasing the value of R2 increases the loop bandwidth which can improve the speed of the converter’s transient response. This can be useful in improving the transient response if a large valued output capacitor is utilized. In 12 The speed of the average current limit circuit is limited by the dynamics of the error amplifier. On a hard output short, it would be possible for the inductor current to increase substantially beyond current limit before the average current limit circuit would react. For this reason, there is a second current limit circuit which turns off switch A if the current ever exceeds approximately 165% of the average current limit value. This provides additional protection in the case of an instantaneous hard output short. Reverse Current Limit The reverse current comparator on switch D monitors the inductor current entering PVOUT. When this current exceeds 375mA (typical), switch D will be turned off for the remainder of the switching cycle. 3521fb For more information www.linear.com/LTC3521 LTC3521 Operation Burst Mode Operation With the PWM pin held low, the buck-boost converter operates utilizing a variable frequency switching algorithm designed to improve efficiency at light load and reduce the standby current at zero load. In Burst Mode operation, the inductor is charged with fixed peak amplitude current pulses. These current pulses are repeated as often as necessary to maintain the output regulation voltage. The maximum output current which can be supplied in Burst Mode operation is dependent upon the input and output voltage as given by the following formula: IOUT(MAX),BURST = 0.1• VIN ( A) VIN + VOUT In Burst Mode operation, the error amplifier is not used but is instead placed in a low current standby mode to reduce supply current and improve light load efficiency. Soft-Start The buck-boost converter has an internal voltage mode soft-start circuit with a nominal duration of 600μs. The converter remains in regulation during soft-start and will therefore respond to output load transients that occur during this time. In addition, the output voltage rise time has minimal dependency on the size of the output capacitor or load. During soft-start, the buck-boost converter is forced into PWM operation regardless of the state of the PWM pin. PGOOD Comparator The PGOOD1 pin is an open-drain output which indicates the status of the buck-boost converter. In Burst Mode operation (PWM = Low), the PGOOD1 open-drain output will pull low when the feedback voltage falls 9% below the regulation voltage. There is approximately 3% hysteresis in this threshold when the output voltage is returning good. In addition, there is a 60μs typical deglitching delay to prevent false trips due to short duration voltage transients in response to load steps. In PWM mode, operation of the PGOOD1 comparator is complicated by the fact that the feedback pin voltage is driven to the reference voltage independent of the output voltage through the action of the voltage mode error amplifier. Since the soft-start is voltage mode, the feedback voltage will track the output voltage correctly during soft-start, and the PGOOD1 output will correctly indicate the point at which the buck-boost attains regulation at the end of soft-start. Therefore, the PGOOD1 output can be utilized for sequencing purposes. Once in regulation, the feedback voltage will no longer track the output voltage, and the PGOOD1 pin will not directly respond to a loss of regulation in the output. However, the only means by which a loss of regulation can occur is if the current limit has been reached, thereby preventing the buck-boost converter from delivering the required output current. In such cases, the occurrence of current limit will cause the PGOOD1 flag to fall indicating a fault state. There can be cases, however, when the buck-boost converter is continuously in current limit, causing the PGOOD1 output to pull low, while the output voltage still remains slightly above the PGOOD1 comparator trip point. The PGOOD1 output also pulls low during overtemperature shutdown, undervoltage lockout or if the SHDN1 pin is pulled low. Common Functions Thermal Shutdown If the die temperature exceeds 150°C, all three converters will be disabled. All power devices will be turned off and all switch nodes will be high impedance. The soft-start circuits for all three converters are reset during thermal shutdown to provide a smooth recovery once the overtemperature condition is eliminated. All three converters will restart (if enabled) when the die temperature drops to approximately 140°C. Undervoltage Lockout If the supply voltage decreases below 1.7V (typical) then all three converters will be disabled and all power devices will be turned off. The soft-start circuits for all three converters are reset during undervoltage lockout to provide a smooth restart once the input voltage rises above the undervoltage lockout threshold. 3521fb For more information www.linear.com/LTC3521 13 LTC3521 Applications Information The basic LTC3521 application circuit is shown as the Typical Application on the front page of this data sheet. The external component selection is determined by the desired output voltages, output currents and ripple voltage requirements of each particular application. Basic guidelines and considerations for the design process are provided in this section. Table 1 depicts the recommended inductance for several common output voltages. Table 1. Buck Recommended Inductance OUTPUT VOLTAGE MINIMUM INDUCTANCE MAXIMUM INDUCTANCE 0.6V 1.5μH 2.2μH 1.2V 2.2μH 4.7μH Buck Inductor Selection 1.8V 3.3μH 6.8μH The choice of buck inductor value influences both the efficiency and the magnitude of the output voltage ripple. Larger inductance values will reduce inductor current ripple and lead to lower output voltage ripple. For a fixed DC resistance, a larger value inductor will yield higher efficiency by lowering the peak current closer to the average. However, a larger inductor within the same family will generally have a greater series resistance, thereby offsetting this efficiency advantage. 2.5V 4.7μH 8.2μH Given a desired peak-to-peak current ripple, ΔIL, the required inductance can be calculated via the following expression, where f represents the switching frequency in MHz: ⎛ V ⎞ 1 L= VOUT ⎜1– OUT ⎟ (µH) fΔIL VIN ⎠ ⎝ A reasonable choice for ripple current is ΔIL = 240mA which represents 40% of the maximum 600mA load current. The DC current rating of the inductor should be at least equal to the maximum load current, plus half the ripple current, in order to prevent core saturation and loss of efficiency during operation. To optimize efficiency, the inductor should have a low series resistance. In particularly space-restricted applications, it may be advantageous to use a much smaller value inductor at the expense of larger ripple current. In such cases, the converter will operate in discontinuous conduction for a wider range of output loads and efficiency will be reduced. In addition, there is a minimum inductor value required to maintain stability of the current loop (given the fixed internal slope compensation). Specifically, if the buck converter is going to be utilized at duty cycles over 40%, the inductance value must be at least LMIN , as given by the following equation: Buck Output Capacitor Selection A low ESR output capacitor should be utilized at the buck output in order to minimize voltage ripple. Multilayer ceramic capacitors are an excellent choice as they have low ESR and are available in small footprints. In addition to controlling the ripple magnitude, the value of the output capacitor also sets the loop crossover frequency and can, therefore, impact loop stability. There is both a minimum and maximum capacitance value required to ensure stability of the loop. If the output capacitance is too small, the loop crossover frequency will increase to the point where the switching delay and the high frequency parasitic poles of the error amplifier will degrade the phase margin. In addition, the wider bandwidth produced by a small output capacitor will make the loop more susceptible to switching noise. At the other extreme, if the output capacitor is too large, the crossover frequency can decrease too far below the compensation zero and lead to a degraded phase margin. Table 2 provides a guideline for the range of allowable values of low ESR output capacitors. Larger value output capacitors can be accommodated provided they have sufficient ESR to stabilize the loop. Table 2. Buck Output Capacitor Range VOUT CMIN CMAX 0.6V 15μF 300μF 0.8V 15μF 230μF 1.2V 10μF 150μF 1.8V 10μF 90μF 2.7V 10μF 70μF 3.3V 6.8μF 50μF LMIN = 2.5 • VOUT (µH) 14 3521fb For more information www.linear.com/LTC3521 LTC3521 applications information Buck Input Capacitor Selection Buck-Boost Output Voltage Programming The PVIN2 pin provides current to the buck converter power switch and is the supply pin for the IC’s internal circuitry. It is recommended that a low ESR ceramic capacitor with a value of at least 4.7µF be used to bypass this pin. The capacitor should be placed as close to the pin as possible and have a short return to ground. The buck-boost output voltage is set by a resistive divider according to the following formula: ⎛ R2 ⎞ VOUT1 = 0.6V ⎜1+ ⎟ ⎝ R1 ⎠ Buck Output Voltage Programming The output voltage is set by a resistive divider, according to the following formula: ⎛ R2 ⎞ VOUT2,3 = 0.6V ⎜1+ ⎟ ⎝ R1 ⎠ The external divider is connected to the output, as shown in Figure 3. It is recommended that a feedforward capacitor, CFF , be placed in parallel with resistor R2 to improve the noise immunity of the feedback node. Table 3 provides the recommended resistor and feedforward capacitor combinations for common output voltage options. Table 3. Buck Resistor Divider Values VOUT R1 R2 CFF 0.6V – 0 – 0.8V 200k 69.8k 22pF 1.0V 118k 80.6k 22pF 1.2V 100k 102k 22pF 1.5V 78.7k 121k 22pF 1.8V 68.1k 137k 22pF 2.7V 63.4k 226k 33pF 3.3V 60.4k 274k 33pF Buck-Boost Inductor Selection To achieve high efficiency, a low ESR inductor should be utilized for the buck-boost converter. The inductor must have a saturation rating greater than the worst case average inductor current plus half the ripple current. The peak-to-peak inductor current ripple will be larger in buck and boost mode than in the buck-boost region. The peak-to-peak inductor current ripple for each mode can 0.6V ≤ VOUT3 ≤ 5.25V 0.6V ≤ VOUT2 ≤ 5.25V R2 1.8V ≤ VOUT1 ≤ 5.25V R2 R2 FB2 R1 The external divider is connected to the output, as shown in Figure 4. The buck-boost converter utilizes voltage mode control and the value of R2 plays an integral role in the dynamics of the feedback loop. In general, a larger value for R2 will increase stability and reduce the speed of the transient response. A smaller value of R2 will reduce stability but increase the transient response speed. A good starting point is to choose R2 = 1MΩ, then calculate the required value of R1 to set the desired output voltage according to the above formula. If a large output capacitor is used, the bandwidth of the converter is reduced. In such cases R2 can be reduced to improve the transient response. If a large inductor or small output capacitor is utilized, the loop will be less stable and the phase margin can be improved by increasing the value of R2. FB1 FB3 LTC3521 LTC3521 R1 R1 GND GND 3521 F04 3521 F03 Figure 3. Setting the Buck Output Voltage Figure 4. Setting the Buck-Boost Output Voltage 3521fb For more information www.linear.com/LTC3521 15 LTC3521 applications information be calculated from the following formulas, where f is the frequency in MHz and L is the inductance in μH: ΔIL,P-P,BUCK = 1 VOUT ( VIN – VOUT ) • fL VIN ΔIL,P-P,BOOST = 1 VIN ( VOUT – VIN ) • fL VOUT In addition to affecting output current ripple, the size of the inductor can also affect the stability of the feedback loop. In boost mode, the converter transfer function has a right half plane zero at a frequency that is inversely proportional to the value of the inductor. As a result, a large inductor can move this zero to a frequency that is low enough to degrade the phase margin of the feedback loop. It is recommended that the chosen inductor value be less than 10μH if the buck-boost converter is to be used in the boost region. Buck-Boost Output Capacitor Selection A low ESR output capacitor should be utilized at the buckboost converter output in order to minimize output voltage ripple. Multilayer ceramic capacitors are an excellent choice as they have low ESR and are available in small footprints. The capacitor should be chosen large enough to reduce the output voltage ripple to acceptable levels. Neglecting the capacitor ESR and ESL, the peak-to-peak output voltage ripple can be calculated by the following formulas, where f is the frequency in MHz, COUT is the capacitance in μF, L is the inductance in μH and ILOAD is the output current in amps: I (V – V ) ΔVP-P,BOOST = LOAD OUT IN COUT • VOUT • f ΔVP-P,BUCK = 1 8 • L • COUT • f2 (V – V ) V • IN OUT OUT VIN Since the output current is discontinuous in boost mode, the ripple in this mode will generally be much larger than the magnitude of the ripple in buck mode. In addition to controlling the ripple magnitude, the value of the output capacitor also affects the location of the resonant frequency in the open loop converter transfer function. If the output capacitor is too small, the bandwidth of the converter will extend high enough to degrade the phase margin. To prevent this from happening, it is recommended that a minimum value of 10μF be used for the buck-boost output capacitor. Buck-Boost Input Capacitor Selection The supply current to the buck-boost converter is provided by the PVIN1 pin. It is recommended that a low ESR ceramic capacitor with a value of at least 4.7μF be located as close to this pin as possible. Inductor Style and Core Material Different inductor core materials and styles have an impact on the size and price of an inductor at any given peak current rating. Toroid or shielded pot cores in ferrite or permalloy materials are small and reduce emissions, but generally cost more than powdered iron core inductors with similar electrical characteristics. The choice of inductor style depends upon the price, sizing, and EMI requirements of a particular application. Table 4 provides a sampling of inductors that are well suited to many LTC3521 application circuits. Table 4. Representative Surface Mount Inductors MANUFACTURER PART NUMBER DCR HEIGHT Taiyo Yuden NP03SB4R7M 4.7μH 1.2A 0.047Ω 1.8mm NP03SB6R8M 6.8μH 1A 0.084Ω 1.8mm Coilcraft MSS7341-502NL 5μH 2.3A 0.024Ω 4.1mm DT1608C-472ML 4.7µH 1.2A 0.085Ω 2.92mm 5µH 2.4A 0.026Ω 3mm 2mm CooperBussmann SD7030-5R0-R SD20-6R2-R 6.2µH 1.12A 0.072Ω Sumida CDR6D23MNNP-4R2 4.2µH 2.6A 0.052Ω 2.5mm 1A 0.081Ω 1.8mm CDRH4D16FB/ND6R8N 16 MAX VALUE CURRENT 6.8µH 3521fb For more information www.linear.com/LTC3521 LTC3521 applications information Capacitor Vendor Information PCB Layout Considerations Both the input and output capacitors used with the LTC3521 must be low ESR and designed to handle the large AC currents generated by switching converters. The vendors in Table 5 provide capacitors that are well suited to LTC3521 application circuits. The LTC3521 switches large currents at high frequencies. Special care should be given to the PCB layout to ensure stable, noise-free operation. Figure 5 depicts the recommended PCB layout to be utilized for the LTC3521. A few key guidelines follow: Table 5. Capacitor Vendor Information 1.All circulating high current paths should be kept as short as possible. This can be accomplished by keeping the routes to all bold components in Figure 5 as short and as wide as possible. Capacitor ground connections should via down to the ground plane in the shortest route possible. The bypass capacitors on PVIN1 and PVIN2 should be placed as close to the IC as possible and should have the shortest possible paths to ground. MANUFACTURER WEB SITE REPRESENTATIVE PART NUMBERS Taiyo Yuden www.t-yuden.com JMK212BJ106K 10μF, 6.3V TDK www.component. tdk.com C2012X5R0J106K 10μF, 6.3V Murata www.murata.com GRM21BR60J106K 10μF, 6.3V JMK212BJ226K 22μF, 6.3V GRM32ER61C226K 22μF, 16V AVX www.avxcorp.com SM055C106KHN480 10μF Minimizing solution size is usually a priority. Please be aware that ceramic capacitors can exhibit a significant reduction in effective capacitance when a bias is applied. The capacitors exhibiting the highest reduction are those packaged in the smallest case size. 2.The small-signal ground pad (GND) should have a single point connection to the power ground. A convenient way to achieve this is to short the pin directly to the Exposed Pad as shown in Figure 5. 3.The components shown in bold, and their connections, should all be placed over a complete ground plane. 4.To prevent large circulating currents from disrupting the output voltage sensing, the ground for each resistor divider should be returned directly to the small signal ground pin (GND). 5.Use of vias in the die attach pad will enhance the thermal environment of the converter, especially if the vias extend to a ground plane region on the exposed bottom surface of the PCB. 3521fb For more information www.linear.com/LTC3521 17 LTC3521 applications information KELVIN TO VOUT PAD BUCK VOUT VIA TO GROUND PLANE MINIMIZE TRACE LENGTH NC (19) SW2 (20) PGND1A (9) PVIN2 (22) FB3 (23) FB2 (24) MINIMIZE TRACE LENGTH PGOOD1 (4) SW1A (15) VIN (5) SW1B (14) GND (6) NC (13) DIRECT TIE BACK TO GND PIN KELVIN TO VOUT PAD BUCK VOUT BUCK-BOOST VOUT KELVIN TO VOUT PAD PGND1B (12) VOUT1 (16) PVIN (11) PGOOD2 (3) SHDN1 (10) SW3 (17) SHDN3 (9) PGOOD3 (2) FB1 (8) PGND2 (18) PWM (7) SHDN2 (1) MINIMIZE TRACE LENGTH UNINTERRUPTED GROUND PLANE MUST EXIST UNDER ALL COMPONENTS SHOWN IN BOLD, AND UNDER TRACES CONNECTING TO THOSE COMPONENTS 3521 F05 Figure 5. LTC3521 Recommended PCB Layout 18 3521fb For more information www.linear.com/LTC3521 LTC3521 Typical Application Dual Supercapacitor to 3.3V at 200mA, 1.8V at 50mA and 1.2V at 100mA Backup Power Supply VIN 1.8V TO 5.5V + + VOUT1 3.3V 200mA 1F 1F C4 L1 4.7µF 4.7µH PVIN1 VIN PVIN2 SW2 SW1A L2 4.7µH C1 22µF R2 221k FB2 VOUT1 R1 1.0M LTC3521 OFF BURST ON PWM FB1 SHDN1 SHDN2 SHDN3 SW3 C2 10µF R3 137k SW1B VOUT2 1.8V 50mA R4 68.1k L3 4.7µH VOUT3 1.2V C3 100mA 10µF R5 100k FB3 PGOOD1 PWM PGOOD2 PGOOD3 PGND1A PGND1B GND PGND2 R6 100k 3521 TA02a Converter Output Voltages Efficiency vs VIN 100 VIN 2V/DIV 96 VOUT1 = 3.3V IOUT = 200mA 92 EFFICIENCY (%) VOUT1 2V/DIV VOUT2 2V/DIV VOUT3 2V/DIV 88 VOUT3 = 1.2V IOUT = 100mA 84 80 VOUT2 = 1.8V IOUT = 50mA 76 50µs/DIV 3521 TA02b 72 1.8 2.8 3.8 VIN (V) 4.8 3521 TA02c 3521fb For more information www.linear.com/LTC3521 19 LTC3521 Package Description FE Package 20-Lead Plastic TSSOP (4.4mm) FE Package 20-Lead PlasticLTC TSSOP (Reference DWG(4.4mm) # 05-08-1663 Rev J) (Reference LTC DWG # 05-08-1663 Rev J) Exposed Pad CB Variation Exposed Pad Variation CB 6.40 – 6.60* (.252 – .260) 3.86 (.152) 3.86 (.152) 20 1918 17 16 15 14 13 12 11 6.60 ±0.10 2.74 (.108) 4.50 ±0.10 6.40 2.74 (.252) (.108) BSC SEE NOTE 4 0.45 ±0.05 1.05 ±0.10 0.65 BSC 1 2 3 4 5 6 7 8 9 10 RECOMMENDED SOLDER PAD LAYOUT 4.30 – 4.50* (.169 – .177) 0.09 – 0.20 (.0035 – .0079) 0.25 REF 1.20 (.047) MAX 0° – 8° 0.65 (.0256) BSC 0.50 – 0.75 (.020 – .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 0.195 – 0.30 (.0077 – .0118) TYP 0.05 – 0.15 (.002 – .006) FE20 (CB) TSSOP REV J 1012 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE UF Package UF Package 24-Lead Plastic QFN (4mm × 4mm) 24-Lead Plastic QFN (4mm × 4mm) (ReferenceLTC LTC DWG # 05-08-1697 (Reference DWG # 05-08-1697 Rev B)Rev B) PIN 1 NOTCH R = 0.20 TYP OR 0.35 × 45° CHAMFER BOTTOM VIEW—EXPOSED PAD 4.00 ±0.10 (4 SIDES) 0.70 ±0.05 R = 0.115 TYP 0.75 ±0.05 PIN 1 TOP MARK (NOTE 6) 23 24 0.40 ±0.10 1 2 4.50 ±0.05 2.45 ±0.05 3.10 ±0.05 (4 SIDES) 2.45 ±0.10 (4-SIDES) PACKAGE OUTLINE (UF24) QFN 0105 REV B 0.200 REF 0.25 ±0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 20 0.00 – 0.05 0.25 ±0.05 0.50 BSC NOTE: 1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-X)—TO BE APPROVED 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE, IF PRESENT 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3521fb For more information www.linear.com/LTC3521 LTC3521 Revision History REV DATE DESCRIPTION PAGE NUMBER A 11/10 Addition of PGND1A reflected throughout data sheet Addition of VIN to Typical Applications Revised Note 2 3 Changes to Block Diagram Change to Operation Soft-Start section B 08/13 1, 19, 22 Corrected pin numbers on Block Diagram UF package 9 11, 13 9 3521fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. For more information www.linear.com/LTC3521 21 LTC3521 Typical Application Li-Ion to 3.3V at 800mA, 1.8V at 600mA and 1.2V at 600mA with Sequenced Start-Up VIN 2.4V TO 4.2V + 4.7µF L1 4.7µH Li-Ion L3 4.7µH VOUT3 1.2V 600mA C3 10µF R5 100k R6 100k 499k PVIN1 VIN PVIN2 SW2 SW1A SW1B FB2 SW3 BURST PWM L2 4.7µH C2 10µF R3 137k LTC3521 FB3 VOUT1 PGOOD3 SHDN1 SHDN2 PGOOD1 PGOOD2 PWM SHDN3 PGND1A PGND1B GND PGND2 VOUT2 1.8V 600mA C1 22µF R1 1.0M VOUT1 3.3V 800mA (1A, VIN > 3.0V) OFF SHDN2, 5V/DIV PGOOD2, 5V/DIV PGOOD3, 5V/DIV R2 221k R5 499k VOUT2 2V/DIV VOUT3 2V/DIV VOUT1 2V/DIV R4 68.1k FB1 PGOOD1 Sequenced Start-Up Waveforms 500µs/DIV 3521 TA03b ON 3521 TA03a Related Parts PART NUMBER DESCRIPTION COMMENTS LTC3100 94% Efficiency, VIN: 0.7V to 5V, VOUT(MAX) = 5.25V, IQ = 15µA, 700mA ISW, 1.5MHz, Synchronous Step-Up, 250mA Synchronous Step-Down DC/DC Converter and 100mA LDO ISD < 1µA, 3mm × 3mm QFN-16 Package LTC3101 Wide VIN, Multioutput DC/DC Converter and PowerPath™ Controller, 800mA Buck-Boost, Dual 350mA Buck Converters, 50mA Always-On LDO LTC3409 600mA IOUT, 1.7MHz/2.6MHz, Synchronous Step-Down DC/ 96% Efficiency, VIN: 1.6V to 5.5V, VOUT(MIN) = 0.6V, IQ = 65µA, DC Converter ISD < 1µA, DFN Package LTC3441/LTC3442/ LTC3443 1.2A IOUT, 2MHz, Synchronous Buck-Boost DC/DC Converter 95% Efficiency, VIN: 2.4V to 5.5V, VOUT(MIN): 2.4V to 5.25V, IQ = 50µA, ISD < 1µA, DFN Package LTC3520 1A 2MHz, Synchronous Buck-Boost and 600mA Buck Converter 95% Efficiency, VIN: 2.2V to 5.5V, VOUT(MAX) = 5.25V, IQ = 55µA, ISD < 1µA, 4mm × 4mm QFN-24 Package LTC3522 400mA 2MHz, Synchronous Buck-Boost and 200mA Buck Converter 95% Efficiency, VIN: 2.4V to 5.5V, VOUT(MAX) = 5.25V, IQ = 25µA, ISD < 1µA, 3mm × 3mm QFN-16 Package LTC3531/LTC3531-3/ LTC3531-3.3 200mA IOUT, 1.5MHz, Synchronous Buck-Boost DC/DC Converter 95% Efficiency, VIN: 1.8V to 5.5V, VOUT(MIN): 2V to 5V, IQ = 16µA, ISD < 1µA, ThinSOT and DFN Packages LTC3532 500mA IOUT, 2MHz, Synchronous Buck-Boost DC/DC Converter 95% Efficiency, VIN: 2.4V to 5.5V, VOUT(MIN): 2.4V to 5.25V, IQ = 35µA, ISD < 1µA, MS10 and DFN Packages LTC3547 Dual 300mA IOUT, 2.25MHz, Synchronous Step-Down DC/ DC Converter 95% Efficiency, VIN: 2.5V to 5.5V, VOUT(MIN) = 0.6V, IQ = 40µA, ISD < 1µA, DFN-8 Package 22 Linear Technology Corporation 95% Efficiency, VIN: 1.8V to 5.5V, IQ = 38µA, Standby IQ = 15µA, 4mm × 4mm QFN-24 Package 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTC3521 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com/LTC3521 3521fb LT 0813 REV B • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2010