med 00002267 1454337951 jauch mems oscillator

THE SPECIALISTS
FOR FREQUENCY CONTROL AND BATTERY TECHNOLOGY
MEMS TIMING
MEMS OSCILLATORS
0,6mm
1,5 mm
0,8 mm
NEW AT JAUCH:
TEMPERATURE COMPENSATED MEMS OSCILLATORS
EASY TO USE:
JUST CONNECT VDC, FEED MULTIPLE CLOCK RECEIVERS
VDC
+
μC
RF-SOC
GND
32.768 kHz
clock
JSO15 TR
HIGHEST ACCURACY FOR RTC APPLICATIONS
Product Features
Applications
Additional Services
n
Temperature compensated MEMS oscillator (TCMO)
n
Output frequency 32.768 kHz
n
Best temperature stability ±5 ppm
n
Temperature range -40°C ~ +85°C
n
Variable supply voltage range 1.5 Volt ~ 3.63 Volt
n
CSP 1.5 x 0.8 x 0.6 (chip scale package)
n
High shock and vibration resistance
n
Extremely high reliability
n
Highly accurate Real Time Clocks (RTC)
n
Smart Meters / Automated Meter Reading (AMR)
n
Wearables / Activity Trackers / Smart Watches
n
Mobile Medical Instruments
n
Health and Wellness Monitors
n
Tablets / Mobile Phones
n
Samples of JSO15 TR typically available from stock
n
Free samples shipped without delivery charge within 48 hours
n
Technical customer support by field application engineers
NEW AT JAUCH: MEMS OSCILLATORS
EASY TO CONFIGURE: CHECK OUT OUR WEBSITE
JSO LC SERIES
LOW POWER FOR VERSATILE APPLICATIONS
Product Features
Drop-in Replacement
for the Following Packages
n
Silicon MEMS resonator based oscillators
n
Frequency range 1 MHz ~ 137 MHz
n
Best temperature stability ±20 ppm
n
Widest temperature range - 55°C ~ +125°C
n
Supply voltage range 1.8 Volt ~ 3.3 Volt
n
Compatible to all standard oscillator packages and pad layouts
n
50,000 G shock and 70 G vibration resistance
n
Extremely high reliability
n
2016 (2.0 x 1.6 x 0.75 mm)
n
2520 (2.5 x 2.0 x 0.75 mm)
n
3225 (3.2 x 2.5 x 0.75 mm)
n
5032 (5.0 x 3.2 x 0.75 mm)
n
7050 (7.5 x 5.0 x 0.90 mm)
n
Local configuration center in Germany
n
Technical customer support by field application engineers
n
Free samples shipped without delivery charge within 48 hours
Additional Services
MEMS-TCXO · JSO TR · 32.768kHz
n wide supply voltage range 1.5 V ~ 3.63 V
n very low supply current
n ultra-stable 32.768 kHz clock source
n ultra-small CSP package 1.5 x 0.8 mm
n very short start-up time
n can replace tuning fork crystals
actual size
General Data
Table 1: Frequency Stability Code
type
JSO15B1TR
stability code / temp. code
supply voltage VDC
1.5 V ~ 3.63 V
including frequency tolerance*
±22 ppm ±13 ppm ±10 ppm
current consumption typ.
1.2 µA (rail-to-rail mode, no load, VDC = 1.8 V)
excluding frequency tolerance**
±20 ppm ±10 ppm
output frequency
32.768 kHz
0°C ~ +70°C
T0
O
O
O
frequency stability vs. temp.
±10 ppm ~ ±22 ppm (see table 1)
-40°C ~ +85°C
T1
O
O
O
frequency stability vs. voltage
±0.75 ppm at 1.8 V ±0.18 V
O available
±1.5 ppm at 1.5 V ~ 3.63 V
* includes tolerance at 25°C and frequency stability in operating temp. range.
** frequency stability in operating temp. range, frequency tolerance excluded.
aging
at +25°C
±1 ppm first year
temperature
operating
0°C ~ +70°C / -40°C ~ +85°C
storage
-50°C ~ +125°C
low level max.
0.1 x VDC
output
D
K
F
±5 ppm
Table 2: Current Consumption typ. (for max. add 40%)
high level min. 0.9 x VDC
supply current at load
none
load max.
15 pF
at startup (150 ms max.)
30.0
µA
current max.
1.0 µA
during temp. compensation*
6.0
µA
rise & fall time 200 ns max. (15 pF, 10 <-> 90 %)
5 pF
10 pF
15 pF
unit
VRR = 1.80 V, compensation inactive
1.2
1.5
1.8
2.1
µA
50 ns max. (5 pF, 10 <-> 90 %)
VRR = 2.50 V, compensation inactive
1.3
1.7
2.0
2.5
µA
start-up time max.
400 ms
VRR = 3.30 V, compensation inactive
1.4
1.9
2.5
3.0
µA
power supply ramp max.
100 ms
* repetitive temp. compensation consuming 6 µA for 10 ms, repeating every 350 ms
period jitter RMS typ.
35 ns
More information about the features of the JSO TR 32.768 kHz TCXO can be found here.
#3
#4
ø 0.25
(3)
ø 0.35
(4)
ø 0.315±0.015
#1
#2
#2
top view
side view
#1
bottom view
Packing Note / Marking
#4
#1
#3
0.41
1.00
(2)
(1)
1.00
(2)
0.41
#3
0.60 max.
#4
0.04
1.54±0.02
0.84±0.02
Dimensions
(1) polymer coating thickness
(2) basic spacing between centers
(3) non-solder mask defined pads
(4) soldermask opening diameter
pin connection
#1: GND
#2: output
#3: VDC
#4: GND
#2
pad layout
in mm
Pin Connection
QTY < 1K pcs. ➝ cut tape
QTY 1K/3K ➝ tape and reel
Marking: identifier for pin 1
#4
#3
#1
#2
# 4: GND
# 3: VDC
# 1: GND
# 2: output
RoHS
2011/65/EC
RoHS compliant
Pb free
REACH compliant
Conflict mineral free
Jauch MEMS – Uses SiTime’s MEMS First™ technology
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
081214
MEMS-TCXO · JSO TR · 32.768kHz
Order Information
Example:
O 0.032768 – JSO 15 B1 T R – F – 1V3 – T0 – R R – D
DC coupling
D = DC
O = Oscillator
frequency
output
R R = rail-to-rail
JSO = Jauch Silicon Oscillator
temperature range
T0 = 0°C ~ +70°C
T1 = -40°C ~ +85°C
see table 1
package
15 = 1.5 x 0.8 mm CSP
version/revision
supply voltage
1V3 = variable supply voltage 1.5 V ~ 3.63 V
f unction/feature
T = TCXO
frequency stability
F = ±5 ppm
K = ±10 ppm
D = ±20 ppm
see table 1
usage
R = for RTC (real time clock)
Note
Standard type O 0.032768-JSO15B1TR-F-1V3-T1-RR-D typically available from stock
Frequency stability (table 1): F = ±5 ppm
Operating temperature range: T1 = -40°C ~ +85°C
Supply voltage:
1V3 = 1.5 V ~ 3.63 V variable
Taping Specification
8.4 +1.5/-0
4.0±0.1
0.96±0.03
ø 0.18 min.
ø 180.5
ø 60
8.3 max.
1.5 min.
ø 13
0.2±0.02
ø 21
2.0±0.05
1.66±0.03
ø 1.55±0.05
5.25±0.1
4.0±0.1
1.75±0.1
120°
0.63±0.3
Direction of feed
up to 3000 pcs per reel
in mm
Reflow Soldering Profile
temperature (°C)
260
200
10 s max.
260 °C max.
220 ±5 °C
180 ±5 °C
150
100
60 ~180 s
60 s max.
50
time (s)
note: parts are also suitable for soldering systems with lead (Pb) content.
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
MEMS-Oscillator · JSO LC series · 1.8 V
actual sizes
2016
2520
3225
5032
7050
General Data
Table 1: Frequency Stability Code
type
JSOxxCxLC 1.8 V
stability code /
frequency range
1.0 ~ 110.0 MHz (temp. range T0 ~ T8)
temp. code*
115.0 ~ 137.0 MHz (temp. range T0 ~ T1)
-20°C ~ +70°C
frequency stability over all
±20 ppm ~ ±50 ppm (see table 1)
-40°C ~ +85°C
current consumption
see table 2
supply voltage VDC
temperature
operating
B
G
C
D
±50 ppm
±30 ppm
±25 ppm
±20 ppm
T0
O
O
O
O
T1
O
O
O
O
-40°C ~ +105°C
T2
O
O
O
O
1.8 V ± 10%
-40°C ~ +125°C
T3
O
O
O
O
T0 = -20°C ~ +70°C
-55°C ~ +125°C
T8
O
O
O
T1 = -40°C ~ +85°C
O available
T2 = -40°C ~ +105°C
* includes stability at 25°C, operating temp. range, supply voltage change,
shock and vibration, aging 1st year.
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
output
storage
-55°C ~ +150°C
logic
HCMOS/LVCMOS
Table 2: Current Consumption typ. (for max. add 30%)
rise & fall time 4.2 ns max. at 15 pF / 6.8 ns max. at 30 pF (see table 4)
load max.
n configured to customer’s specification
n extended shock & vibration resistance
n very fast delivery service
n 500 million hours MTBF
n low power oscillator with
HCMOS/LVCMOS output
n compatible to industry standard
packages 2016 – 7050
30 pF max. recommended (≤ 74.0 MHz)
15 pF max. recommended (> 74.0 MHz)
other load capacitances possible, see supplementary document
current max.
2 mA
low level max.
0.1 x VDC
high level min. 0.9 x VDC
standby function (e/d)
stop (S), tristate-only (T) or none (N), see table 3
output enable time max.
5 ms (S) / 150 ns (T)
output disable time max.
150 ns
start-up time max.
5 ms
standby current max.
2 µA (for stop (S), see table 3)
phase jitter 12 kHz ~ 20 MHz
< 3.0 ps RMS
symmetry at 0.5 x VDC
45% ~ 55% (standard)
current at load
5 pF
15 pF
30 pF
60 pF
unit
output disabled
3.5
3.5
3.5
3.5
mA
1.0 ~ 19.9 MHz
3.6
3.9
4.4
5.5
mA
20.0 ~ 29.9 MHz
4.2
4.5
5.4
6.5
mA
30.0 ~ 49.9 MHz
4.5
5.1
6.5
50.0 ~ 79.9 MHz
4.9
6.3
mA
80.0 ~ 110.0 MHz
5.7
7.6
mA
115.0 ~ 137.0 MHz
(8.0)
(13.0)
mA
mA
note: current at default edge control setting “D”, also refer to table 4.
Table 3: Configurable Standby Function Options (e/d)
note: some frequencies can’t be configured, see table 5.
pin #1 (e/d control)
option
functionality
low “0” (VIL ≤ 0.2 VDC)
S = Stop
output weakly pulled down, oscillator in sleep mode
T = TriState
output high impedance, oscillator operates
N = None
oscillator output active
high “1” (VIH ≥ 0.8 VDC)
all
oscillator output active
open*
all
oscillator output active
* a pull up resistor is recommended in EMI stressed circuit environments.
Packing Note / Marking
Pin Connection
QTY < 250 pcs. ➝ cut tape
QTY 250/500/1K/3K pcs. ➝ tape and reel
Marking: lot code only
#4
#3
#1
#2
# 4: VDC
# 3: output
# 1: e/d
# 2: GND
note: a capacitor of 0.1 µF between VDC and GND is recommended.
RoHS
2011/65/EC
RoHS compliant
Pb free
REACH compliant
Conflict mineral free
Jauch MEMS – Uses SiTime’s MEMS First™ technology
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
081214
MEMS-Oscillator · JSO LC series · 1.8 V
Table 4: Max. Rise & Fall Time vs. Load Capacitance
CL
5 pF
edge control
15 pF
30 pF
5 pF
at 10% ~ 90% of VDC (ns)
15 pF
30 pF
at 20% ~ 80% of VDC (ns)
Table 5: Non-Configurable Frequencies
operating temperature option
operating temperature option
T2 − (-40°C ~ +105°C)
T8 − (-55°C ~ +125°C)
D = 0*
1.8
4.2
6.8
1.2
2.8
4.8
T3 − (-40°C ~ +125°C)
1
2.2
5.0
7.6
1.4
3.4
5.2
from (MHz)
to (MHz)
from (MHz)
to (MHz)
2
2.4
5.6
8.8
1.6
3.8
6.0
61.223
61.674
61.223
61.974
3
2.8
6.0
10.0
1.8
4.2
6.8
69.796
70.485
69.240
70.827
4
4.8
9.8
17.0
3.4
6.6
11.6
79.063
79.162
78.715
79.561
5
6.6
12.6
21.0
4.4
8.6
15.0
81.428
82.232
80.160
80.174
6
10.0
18.0
32.0
6.6
12.0
22.0
91.834
92.155
80.780
82.632
7
18.0
34.0
62.0
12.4
24.0
44.0
94.249
94.430
91.834
95.474
94.875
94.994
96.192
96.209
97.714
98.679
96.936
99.158
110.0
115.194
110.0
119.342
117.811
118.038
–
–
118.594
118.743
120.239
120.262
122.142
122.705
121.170
121.243
123.022
123.348
121.601
123.948
* default edge control setting “D” at VDC = 1.8 V, please also refer to the
supplementary information on our homepage for typical values and more details.
Order Information
Example:
O 26.123456 – JSO 75 C1 L C – B – 1.8 – T0 – S – D
O = Oscillator
frequency (8 digits), see also table 5
1.0 ~ 110.0 MHz
115.0 ~ 137.0 MHz
JSO = Jauch Silicon Oscillator
package
75 = 7050
53 = 5032
32 = 3225
22 = 2520
21 = 2016
frequency range
C1 = 1.0 ~ 110.0 MHz
C2 = 115.0 ~ 137.0 MHz
function/feature
L = lowpower
output I/F
C = (H)CMOS
edge control
D = default
0 – 7, see table 4
standby function options
S = Stop
T = TriState
N = None
temperature range
T0 = -20°C ~ +70°C
T1 = -40°C ~ +85°C
T2 = -40°C ~ +105°C
supply voltage
3.3 = 3.3 V
3.0 = 3.0 V
2.8 = 2.8 V
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
2.5 = 2.5 V
1.8 = 1.8 V
2V3 = 2.5 V ~ 3.3 V
frequency stability overall
B = ± 50 ppm
C = ± 25 ppm
G = ± 30 ppm
D = ± 20 ppm
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
MEMS-Oscillator · JSO LC series · 2.5 V
actual sizes
2016
2520
3225
5032
7050
n configured to customer’s specification
n extended shock & vibration resistance
n very fast delivery service
n 500 million hours MTBF
n low power oscillator with
HCMOS/LVCMOS output
n compatible to industry standard
packages 2016 – 7050
General Data
Table 1: Frequency Stability Code
type
JSOxxCxLC 2.5 V
stability code /
frequency range
1.0 ~ 110.0 MHz (temp. range T0 ~ T8)
temp. code*
115.0 ~ 137.0 MHz (temp. range T0 ~ T1)
-20°C ~ +70°C
T0
O
O
O
O
frequency stability over all
±20 ppm ~ ±50 ppm (see table 1)
-40°C ~ +85°C
T1
O
O
O
O
current consumption
see table 2
-40°C ~ +105°C
T2
O
O
O
O
supply voltage VDC
2.5 V ± 10%
-40°C ~ +125°C
T3
O
O
O
O
temperature
T0 = -20°C ~ +70°C
-55°C ~ +125°C
T8
O
O
O
T1 = -40°C ~ +85°C
O available
T2 = -40°C ~ +105°C
* includes stability at 25°C, operating temp. range, supply voltage change,
shock and vibration, aging 1st year.
operating
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
output
storage
-55°C ~ +150°C
logic
HCMOS/LVCMOS
30 pF max. recommended (≤ 83.0 MHz)
15 pF max. recommended (> 83.0 MHz)
other load capacitances possible, see supplementary document
current max.
3 mA
low level max.
0.1 x VDC
G
C
D
±50 ppm
±30 ppm
±25 ppm
±20 ppm
Table 2: Current Consumption typ. (for max. add 30%)
rise & fall time 3.0 ns max. at 15 pF / 6.0 ns max. at 30 pF (see table 4)
load max.
B
high level min. 0.9 x VDC
standby function (e/d)
stop (S), tristate-only (T) or none (N), see table 3
output enable time max.
5 ms (S) / 150 ns (T)
output disable time max.
150 ns
start-up time max.
5 ms
standby current max.
3 µA (for stop (S), see table 3)
phase jitter 12 kHz ~ 20 MHz
< 3.0 ps RMS
symmetry at 0.5 x VDC
45% ~ 55% (standard)
current at load
5 pF
15 pF
30 pF
60 pF
unit
output disabled
3.7
3.7
3.7
3.7
mA
1.0 ~ 19.9 MHz
3.8
4.2
5.0
6.4
mA
20.0 ~ 29.9 MHz
4.3
5.0
6.4
9.0
mA
30.0 ~ 49.9 MHz
4.7
5.8
7.8
11.6
mA
50.0 ~ 79.9 MHz
5.6
7.6
10.7
80.0 ~ 110.0 MHz
6.6
9.2
mA
115.0 ~ 137.0 MHz
(8.5)
(13.0)
mA
mA
note: current at default edge control setting “D”, also refer to table 4.
Table 3: Configurable Standby Function Options (e/d)
note: some frequencies can’t be configured, see table 5.
pin #1 (e/d control)
option
functionality
low “0” (VIL ≤ 0.2 VDC)
S = Stop
output weakly pulled down, oscillator in sleep mode
T = TriState
output high impedance, oscillator operates
N = None
oscillator output active
high “1” (VIH ≥ 0.8 VDC)
all
oscillator output active
open*
all
oscillator output active
* a pull up resistor is recommended in EMI stressed circuit environments.
Packing Note / Marking
Pin Connection
QTY < 250 pcs. ➝ cut tape
QTY 250/500/1K/3K pcs. ➝ tape and reel
Marking: lot code only
#4
#3
#1
#2
# 4: VDC
# 3: output
# 1: e/d
# 2: GND
note: a capacitor of 0.1 µF between VDC and GND is recommended.
RoHS
2011/65/EC
RoHS compliant
Pb free
REACH compliant
Conflict mineral free
Jauch MEMS – Uses SiTime’s MEMS First™ technology
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
081214
MEMS-Oscillator · JSO LC series · 2.5 V
Table 4: Max. Rise & Fall Time vs. Load Capacitance
CL
5 pF
edge control
15 pF
30 pF
5 pF
at 10% ~ 90% of VDC (ns)
15 pF
30 pF
at 20% ~ 80% of VDC (ns)
Table 5: Non-Configurable Frequencies
operating temperature option
operating temperature option
T2 − (-40°C ~ +105°C)
T8 − (-55°C ~ +125°C)
0
1.2
2.4
5.2
0.8
1.7
3.4
T3 − (-40°C ~ +125°C)
1
1.4
2.6
5.8
0.9
1.9
3.8
from (MHz)
to (MHz)
from (MHz)
to (MHz)
D = 2*
1.6
3.0
6.0
1.1
2.1
4.0
61.223
61.674
61.223
61.974
3
1.8
4.0
6.6
1.2
2.6
4.6
69.796
70.485
69.240
70.827
4
3.2
6.4
11.0
2.2
4.4
7.8
79.063
79.162
78.715
79.561
5
4.4
8.4
14.6
2.9
5.8
10.4
81.428
82.232
80.160
80.174
6
6.6
12.4
23.0
4.4
8.6
15.2
91.834
92.155
80.780
82.632
7
12.8
25.0
46.0
8.6
16.6
30.0
94.249
94.430
91.834
95.474
94.875
94.994
96.192
96.209
97.714
98.679
96.936
99.158
110.0
115.194
110.0
119.342
117.811
118.038
–
–
118.594
118.743
120.239
120.262
122.142
122.705
121.170
121.243
123.022
123.348
121.601
123.948
* default edge control setting “D” at VDC = 2.5 V, please also refer to the
supplementary information on our homepage for typical values and more details.
Order Information
Example:
O 26.123456 – JSO 75 C1 L C – B – 2.5 – T0 – S – D
O = Oscillator
frequency (8 digits), see also table 5
1.0 ~ 110.0 MHz
115.0 ~ 137.0 MHz
JSO = Jauch Silicon Oscillator
package
75 = 7050
53 = 5032
32 = 3225
22 = 2520
21 = 2016
frequency range
C1 = 1.0 ~ 110.0 MHz
C2 = 115.0 ~ 137.0 MHz
function/feature
L = lowpower
output I/F
C = (H)CMOS
edge control
D = default
0 – 7, see table 4
standby function options
S = Stop
T = TriState
N = None
temperature range
T0 = -20°C ~ +70°C
T1 = -40°C ~ +85°C
T2 = -40°C ~ +105°C
supply voltage
3.3 = 3.3 V
3.0 = 3.0 V
2.8 = 2.8 V
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
2.5 = 2.5 V
1.8 = 1.8 V
2V3 = 2.5 V ~ 3.3 V
frequency stability overall
B = ± 50 ppm
C = ± 25 ppm
G = ± 30 ppm
D = ± 20 ppm
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
MEMS-Oscillator · JSO LC series · 2.8 V
actual sizes
2016
2520
3225
5032
7050
General Data
Table 1: Frequency Stability Code
type
JSOxxCxLC 2.8 V
stability code /
frequency range
1.0 ~ 110.0 MHz (temp. range T0 ~ T8)
temp. code*
115.0 ~ 137.0 MHz (temp. range T0 ~ T1)
-20°C ~ +70°C
frequency stability over all
±20 ppm ~ ±50 ppm (see table 1)
-40°C ~ +85°C
current consumption
see table 2
supply voltage VDC
temperature
operating
B
G
C
D
±50 ppm
±30 ppm
±25 ppm
±20 ppm
T0
O
O
O
O
T1
O
O
O
O
-40°C ~ +105°C
T2
O
O
O
O
2.8 V ± 10%
-40°C ~ +125°C
T3
O
O
O
O
T0 = -20°C ~ +70°C
-55°C ~ +125°C
T8
O
O
O
T1 = -40°C ~ +85°C
O available
T2 = -40°C ~ +105°C
* includes stability at 25°C, operating temp. range, supply voltage change,
shock and vibration, aging 1st year.
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
output
storage
-55°C ~ +150°C
logic
HCMOS/LVCMOS
Table 2: Current Consumption typ. (for max. add 30%)
rise & fall time 2.9 ns max. at 15 pF / 5.7 ns max. at 30 pF (see table 4)
load max.
n configured to customer’s specification
n extended shock & vibration resistance
n very fast delivery service
n 500 million hours MTBF
n low power oscillator with
HCMOS/LVCMOS output
n compatible to industry standard
packages 2016 – 7050
30 pF max. recommended (≤ 88.0 MHz)
15 pF max. recommended (> 88.0 MHz)
other load capacitances possible, see supplementary document
current max.
3 mA
low level max.
0.1 x VDC
high level min. 0.9 x VDC
standby function (e/d)
stop (S), tristate-only (T) or none (N), see table 3
output enable time max.
5 ms (S) / 150 ns (T)
output disable time max.
150 ns
start-up time max.
5 ms
standby current max.
4 µA (for stop (S), see table 3)
phase jitter 12 kHz ~ 20 MHz
< 3.0 ps RMS
symmetry at 0.5 x VDC
45% ~ 55% (standard)
current at load
5 pF
15 pF
30 pF
60 pF
unit
output disabled
3.8
3.8
3.8
3.8
mA
1.0 ~ 19.9 MHz
4.1
4.3
5.2
6.9
mA
20.0 ~ 29.9 MHz
4.4
5.2
6.7
9.8
mA
30.0 ~ 49.9 MHz
4.8
6.2
8.3
12.7
mA
50.0 ~ 79.9 MHz
6.1
8.1
11.7
80.0 ~ 110.0 MHz
7.0
10.0
mA
115.0 ~ 137.0 MHz
(9.0)
(14.0)
mA
mA
note: current at default edge control setting “D”, also refer to table 4.
Table 3: Configurable Standby Function Options (e/d)
note: some frequencies can’t be configured, see table 5.
pin #1 (e/d control)
option
functionality
low “0” (VIL ≤ 0.2 VDC)
S = Stop
output weakly pulled down, oscillator in sleep mode
T = TriState
output high impedance, oscillator operates
N = None
oscillator output active
high “1” (VIH ≥ 0.8 VDC)
all
oscillator output active
open*
all
oscillator output active
* a pull up resistor is recommended in EMI stressed circuit environments.
Packing Note / Marking
Pin Connection
QTY < 250 pcs. ➝ cut tape
QTY 250/500/1K/3K pcs. ➝ tape and reel
Marking: lot code only
#4
#3
#1
#2
# 4: VDC
# 3: output
# 1: e/d
# 2: GND
note: a capacitor of 0.1 µF between VDC and GND is recommended.
RoHS
2011/65/EC
RoHS compliant
Pb free
REACH compliant
Conflict mineral free
Jauch MEMS – Uses SiTime’s MEMS First™ technology
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
081214
MEMS-Oscillator · JSO LC series · 2.8 V
Table 4: Max. Rise & Fall Time vs. Load Capacitance
CL
5 pF
edge control
15 pF
30 pF
5 pF
at 10% ~ 90% of VDC (ns)
15 pF
30 pF
at 20% ~ 80% of VDC (ns)
Table 5: Non-Configurable Frequencies
operating temperature option
operating temperature option
T2 − (-40°C ~ +105°C)
T8 − (-55°C ~ +125°C)
0
1.2
2.2
4.6
0.8
1.6
3.0
T3 − (-40°C ~ +125°C)
1
1.3
2.4
5.2
0.9
1.8
3.5
from (MHz)
to (MHz)
from (MHz)
to (MHz)
D = 2*
1.5
2.9
5.7
1.0
2.0
3.8
61.223
61.674
61.223
61.974
3
1.6
3.6
6.4
1.1
2.4
4.4
69.796
70.485
69.240
70.827
4
3.0
6.2
10.4
2.0
4.2
7.4
79.063
79.162
78.715
79.561
5
4.0
7.6
13.6
2.8
5.4
9.4
81.428
82.232
80.160
80.174
6
5.8
11.6
21.0
4.0
8.0
14.2
91.834
92.155
80.780
82.632
7
12.0
23.0
42.0
8.2
15.2
28.0
94.249
94.430
91.834
95.474
94.875
94.994
96.192
96.209
97.714
98.679
96.936
99.158
110.0
115.194
110.0
119.342
117.811
118.038
–
–
118.594
118.743
120.239
120.262
122.142
122.705
121.170
121.243
123.022
123.348
121.601
123.948
* default edge control setting “D” at VDC = 2.8 V, please also refer to the
supplementary information on our homepage for typical values and more details.
Order Information
Example:
O 26.123456 – JSO 75 C1 L C – B – 2.8 – T0 – S – D
O = Oscillator
frequency (8 digits), see also table 5
1.0 ~ 110.0 MHz
115.0 ~ 137.0 MHz
JSO = Jauch Silicon Oscillator
package
75 = 7050
53 = 5032
32 = 3225
22 = 2520
21 = 2016
frequency range
C1 = 1.0 ~ 110.0 MHz
C2 = 115.0 ~ 137.0 MHz
function/feature
L = lowpower
output I/F
C = (H)CMOS
edge control
D = default
0 – 7, see table 4
standby function options
S = Stop
T = TriState
N = None
temperature range
T0 = -20°C ~ +70°C
T1 = -40°C ~ +85°C
T2 = -40°C ~ +105°C
supply voltage
3.3 = 3.3 V
3.0 = 3.0 V
2.8 = 2.8 V
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
2.5 = 2.5 V
1.8 = 1.8 V
2V3 = 2.5 V ~ 3.3 V
frequency stability overall
B = ± 50 ppm
C = ± 25 ppm
G = ± 30 ppm
D = ± 20 ppm
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
MEMS-Oscillator · JSO LC series · 3.0 V
actual sizes
2016
2520
3225
5032
7050
General Data
Table 1: Frequency Stability Code
type
JSOxxCxLC 3.0 V
stability code /
frequency range
1.0 ~ 110.0 MHz (temp. range T0 ~ T8)
temp. code*
115.0 ~ 137.0 MHz (temp. range T0 ~ T1)
-20°C ~ +70°C
frequency stability over all
±20 ppm ~ ±50 ppm (see table 1)
-40°C ~ +85°C
current consumption
see table 2
supply voltage VDC
temperature
operating
B
G
C
D
±50 ppm
±30 ppm
±25 ppm
±20 ppm
T0
O
O
O
O
T1
O
O
O
O
-40°C ~ +105°C
T2
O
O
O
O
3.0 V ± 10%
-40°C ~ +125°C
T3
O
O
O
O
T0 = -20°C ~ +70°C
-55°C ~ +125°C
T8
O
O
O
T1 = -40°C ~ +85°C
O available
T2 = -40°C ~ +105°C
* includes stability at 25°C, operating temp. range, supply voltage change,
shock and vibration, aging 1st year.
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
output
storage
-55°C ~ +150°C
logic
HCMOS/LVCMOS
Table 2: Current Consumption typ. (for max. add 30%)
rise & fall time 3.3 ns max. at 15 pF / 6.2 ns max. at 30 pF (see table 4)
load max.
n configured to customer’s specification
n extended shock & vibration resistance
n very fast delivery service
n 500 million hours MTBF
n low power oscillator with
HCMOS/LVCMOS output
n compatible to industry standard
packages 2016 – 7050
30 pF max. recommended (≤ 81.0 MHz)
15 pF max. recommended (> 81.0 MHz)
other load capacitances possible, see supplementary document
current max.
4 mA
low level max.
0.1 x VDC
high level min. 0.9 x VDC
standby function (e/d)
stop (S), tristate-only (T) or none (N), see table 3
output enable time max.
5 ms (S) / 150 ns (T)
output disable time max.
150 ns
start-up time max.
5 ms
standby current max.
5 µA (for stop (S), see table 3)
phase jitter 12 kHz ~ 20 MHz
< 3.0 ps RMS
symmetry at 0.5 x VDC
45% ~ 55% (standard)
current at load
5 pF
15 pF
30 pF
60 pF
unit
output disabled
3.9
3.9
3.9
3.9
mA
1.0 ~ 19.9 MHz
4.1
4.5
5.4
7.2
mA
20.0 ~ 29.9 MHz
4.5
5.4
6.9
10.1
mA
30.0 ~ 49.9 MHz
4.9
6.3
8.6
13.2
mA
50.0 ~ 79.9 MHz
6.1
8.4
12.2
mA
80.0 ~ 110.0 MHz
7.3
10.5
15.5
mA
115.0 ~ 137.0 MHz
(9.5)
(14.0)
mA
note: current at default edge control setting “D”, also refer to table 4.
Table 3: Configurable Standby Function Options (e/d)
note: some frequencies can’t be configured, see table 5.
pin #1 (e/d control)
option
functionality
low “0” (VIL ≤ 0.2 VDC)
S = Stop
output weakly pulled down, oscillator in sleep mode
T = TriState
output high impedance, oscillator operates
N = None
oscillator output active
high “1” (VIH ≥ 0.8 VDC)
all
oscillator output active
open*
all
oscillator output active
* a pull up resistor is recommended in EMI stressed circuit environments.
Packing Note / Marking
Pin Connection
QTY < 250 pcs. ➝ cut tape
QTY 250/500/1K/3K pcs. ➝ tape and reel
Marking: lot code only
#4
#3
#1
#2
# 4: VDC
# 3: output
# 1: e/d
# 2: GND
note: a capacitor of 0.1 µF between VDC and GND is recommended.
RoHS
2011/65/EC
RoHS compliant
Pb free
REACH compliant
Conflict mineral free
Jauch MEMS – Uses SiTime’s MEMS First™ technology
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
081214
MEMS-Oscillator · JSO LC series · 3.0 V
Table 4: Max. Rise & Fall Time vs. Load Capacitance
CL
5 pF
edge control
15 pF
30 pF
5 pF
at 10% ~ 90% of VDC (ns)
15 pF
30 pF
at 20% ~ 80% of VDC (ns)
Table 5: Non-Configurable Frequencies
operating temperature option
operating temperature option
T2 − (-40°C ~ +105°C)
T8 − (-55°C ~ +125°C)
0
1.1
2.0
4.2
0.7
1.4
2.8
T3 − (-40°C ~ +125°C)
1
1.2
2.2
4.8
0.8
1.6
3.3
from (MHz)
to (MHz)
from (MHz)
to (MHz)
2
1.3
2.8
5.4
0.9
1.9
3.6
61.223
61.674
61.223
61.974
D = 3*
1.5
3.3
6.2
1.0
2.2
4.0
69.796
70.485
69.240
70.827
4
2.8
5.8
10.0
1.8
4.0
6.8
79.063
79.162
78.715
79.561
5
3.8
7.4
13.0
2.6
5.2
9.0
81.428
82.232
80.160
80.174
6
5.5
11.0
19.0
3.8
7.6
13.4
91.834
92.155
80.780
82.632
7
11.4
22.0
40.0
7.8
14.6
27.0
94.249
94.430
91.834
95.474
94.875
94.994
96.192
96.209
97.714
98.679
96.936
99.158
110.0
115.194
110.0
119.342
117.811
118.038
–
–
118.594
118.743
120.239
120.262
122.142
122.705
121.170
121.243
123.022
123.348
121.601
123.948
* default edge control setting “D” at VDC = 3.0 V, please also refer to the
supplementary information on our homepage for typical values and more details.
Order Information
Example:
O 26.123456 – JSO 75 C1 L C – B – 3.0 – T0 – S – D
O = Oscillator
frequency (8 digits), see also table 5
1.0 ~ 110.0 MHz
115.0 ~ 137.0 MHz
JSO = Jauch Silicon Oscillator
package
75 = 7050
53 = 5032
32 = 3225
22 = 2520
21 = 2016
frequency range
C1 = 1.0 ~ 110.0 MHz
C2 = 115.0 ~ 137.0 MHz
function/feature
L = lowpower
output I/F
C = (H)CMOS
edge control
D = default
0 – 7, see table 4
standby function options
S = Stop
T = TriState
N = None
temperature range
T0 = -20°C ~ +70°C
T1 = -40°C ~ +85°C
T2 = -40°C ~ +105°C
supply voltage
3.3 = 3.3 V
3.0 = 3.0 V
2.8 = 2.8 V
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
2.5 = 2.5 V
1.8 = 1.8 V
2V3 = 2.5 V ~ 3.3 V
frequency stability overall
B = ± 50 ppm
C = ± 25 ppm
G = ± 30 ppm
D = ± 20 ppm
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
MEMS-Oscillator · JSO LC series · 3.3 V
actual sizes
2016
2520
3225
5032
7050
General Data
Table 1: Frequency Stability Code
type
JSOxxCxLC 3.3 V
stability code /
frequency range
1.0 ~ 110.0 MHz (temp. range T0 ~ T8)
temp. code*
115.0 ~ 137.0 MHz (temp. range T0 ~ T1)
-20°C ~ +70°C
frequency stability over all
±20 ppm ~ ±50 ppm (see table 1)
-40°C ~ +85°C
current consumption
see table 2
supply voltage VDC
temperature
operating
B
G
C
D
±50 ppm
±30 ppm
±25 ppm
±20 ppm
T0
O
O
O
O
T1
O
O
O
O
-40°C ~ +105°C
T2
O
O
O
O
3.3 V ± 10%
-40°C ~ +125°C
T3
O
O
O
O
T0 = -20°C ~ +70°C
-55°C ~ +125°C
T8
O
O
O
T1 = -40°C ~ +85°C
O available
T2 = -40°C ~ +105°C
* includes stability at 25°C, operating temp. range, supply voltage change,
shock and vibration, aging 1st year.
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
output
storage
-55°C ~ +150°C
logic
HCMOS/LVCMOS
Table 2: Current Consumption typ. (for max. add 30%)
rise & fall time 3 ns max. at 15 pF / 6 ns max. at 30 pF (see table 4)
load max.
n configured to customer’s specification
n extended shock & vibration resistance
n very fast delivery service
n 500 million hours MTBF
n low power oscillator with
HCMOS/LVCMOS output
n compatible to industry standard
packages 2016 – 7050
30 pF max. recommended (≤ 83.0 MHz)
15 pF max. recommended (> 83.0 MHz)
other load capacitances possible, see supplementary document
current max.
4 mA
low level max.
0.1 x VDC
high level min. 0.9 x VDC
standby function (e/d)
stop (S), tristate-only (T) or none (N), see table 3
output enable time max.
5 ms (S) / 150 ns (T)
output disable time max.
150 ns
start-up time max.
5 ms
standby current max.
5 µA (for stop (S), see table 3)
phase jitter 12 kHz ~ 20 MHz
< 3.0 ps RMS
symmetry at 0.5 x VDC
45% ~ 55% (standard)
current at load
5 pF
15 pF
30 pF
60 pF
unit
output disabled
4.0
4.0
4.0
4.0
mA
1.0 ~ 19.9 MHz
4.0
4.6
5.6
7.6
mA
20.0 ~ 29.9 MHz
4.6
5.7
7.4
10.9
mA
30.0 ~ 49.9 MHz
5.1
6.7
9.2
14.3
mA
50.0 ~ 79.9 MHz
6.4
9.0
13.2
mA
80.0 ~ 110.0 MHz
7.7
11.2
17.0
mA
115.0 ~ 137.0 MHz
(10.0)
(14.5)
mA
note: current at default edge control setting “D”, also refer to table 4.
Table 3: Configurable Standby Function Options (e/d)
note: some frequencies can’t be configured, see table 5.
pin #1 (e/d control)
option
functionality
low “0” (VIL ≤ 0.2 VDC)
S = Stop
output weakly pulled down, oscillator in sleep mode
T = TriState
output high impedance, oscillator operates
N = None
oscillator output active
high “1” (VIH ≥ 0.8 VDC)
all
oscillator output active
open*
all
oscillator output active
* a pull up resistor is recommended in EMI stressed circuit environments.
Packing Note / Marking
Pin Connection
QTY < 250 pcs. ➝ cut tape
QTY 250/500/1K/3K pcs. ➝ tape and reel
Marking: lot code only
#4
#3
#1
#2
# 4: VDC
# 3: output
# 1: e/d
# 2: GND
note: a capacitor of 0.1 µF between VDC and GND is recommended.
RoHS
2011/65/EC
RoHS compliant
Pb free
REACH compliant
Conflict mineral free
Jauch MEMS – Uses SiTime’s MEMS First™ technology
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
081214
MEMS-Oscillator · JSO LC series · 3.3 V
Table 4: Max. Rise & Fall Time vs. Load Capacitance
CL
5 pF
edge control
15 pF
30 pF
5 pF
at 10% ~ 90% of VDC (ns)
15 pF
30 pF
at 20% ~ 80% of VDC (ns)
Table 5: Non-Configurable Frequencies
operating temperature option
operating temperature option
T2 − (-40°C ~ +105°C)
T8 − (-55°C ~ +125°C)
0
1.0
1.7
3.6
0.7
1.2
2.6
T3 − (-40°C ~ +125°C)
1
1.1
1.8
4.4
0.7
1.3
3.0
from (MHz)
to (MHz)
from (MHz)
to (MHz)
2
1.2
2.6
5.0
0.8
1.8
3.3
61.223
61.674
61.223
61.974
D = 3*
1.3
3.0
6.0
0.9
2.0
3.8
69.796
70.485
69.240
70.827
4
2.6
5.4
9.4
1.5
3.8
6.4
79.063
79.162
78.715
79.561
5
3.4
6.6
12.0
2.4
5.0
8.6
81.428
82.232
80.160
80.174
6
5.2
10.0
17.0
3.6
7.0
12.4
91.834
92.155
80.780
82.632
7
10.4
21.0
35.0
7.4
14.0
25.0
94.249
94.430
91.834
95.474
94.875
94.994
96.192
96.209
97.714
98.679
96.936
99.158
110.0
115.194
110.0
119.342
117.811
118.038
–
–
118.594
118.743
120.239
120.262
122.142
122.705
121.170
121.243
123.022
123.348
121.601
123.948
* default edge control setting “D” at VDC = 3.3 V, please also refer to the
supplementary information on our homepage for typical values and more details.
Order Information
Example:
O 26.123456 – JSO 75 C1 L C – B – 3.3 – T0 – S – D
O = Oscillator
frequency (8 digits), see also table 5
1.0 ~ 110.0 MHz
115.0 ~ 137.0 MHz
JSO = Jauch Silicon Oscillator
package
75 = 7050
53 = 5032
32 = 3225
22 = 2520
21 = 2016
frequency range
C1 = 1.0 ~ 110.0 MHz
C2 = 115.0 ~ 137.0 MHz
function/feature
L = lowpower
output I/F
C = (H)CMOS
edge control
D = default
0 – 7, see table 4
standby function options
S = Stop
T = TriState
N = None
temperature range
T0 = -20°C ~ +70°C
T1 = -40°C ~ +85°C
T2 = -40°C ~ +105°C
supply voltage
3.3 = 3.3 V
3.0 = 3.0 V
2.8 = 2.8 V
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
2.5 = 2.5 V
1.8 = 1.8 V
2V3 = 2.5 V ~ 3.3 V
frequency stability overall
B = ± 50 ppm
C = ± 25 ppm
G = ± 30 ppm
D = ± 20 ppm
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
MEMS-Oscillator · JSO LC series · 2.5 V ~ 3.3 V
actual sizes
2016
2520
3225
5032
7050
General Data
Table 1: Frequency Stability Code
type
JSOxxCxLC 2.5 V ~ 3.3 V
stability code /
frequency range
1.0 ~ 110.0 MHz (temp. range T0 ~ T8)
temp. code*
115.0 ~ 137.0 MHz (temp. range T0 ~ T1)
-20°C ~ +70°C
frequency stability over all
±20 ppm ~ ±50 ppm (see table 1)
-40°C ~ +85°C
current consumption
see table 2
supply voltage VDC
temperature
operating
B
G
C
D
±50 ppm
±30 ppm
±25 ppm
±20 ppm
T0
O
O
O
O
T1
O
O
O
O
-40°C ~ +105°C
T2
O
O
O
O
2.5 V − 10% ~ 3.3 V + 10%
-40°C ~ +125°C
T3
O
O
O
O
T0 = -20°C ~ +70°C
-55°C ~ +125°C
T8
O
O
O
T1 = -40°C ~ +85°C
O available
T2 = -40°C ~ +105°C
* includes stability at 25°C, operating temp. range, supply voltage change,
shock and vibration, aging 1st year.
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
output
storage
-55°C ~ +150°C
logic
HCMOS/LVCMOS
Table 2: Current Consumption typ. (for max. add 30%)
rise & fall time 4.0 ns max. at 15 pF / 6.6 ns max. at 30 pF (see table 4)
load max.
n configured to customer’s specification
n extended shock & vibration resistance
n very fast delivery service
n 500 million hours MTBF
n low power oscillator with
HCMOS/LVCMOS output
n compatible to industry standard
packages 2016 – 7050
30 pF max. recommended (≤ 76.0 MHz)
15 pF max. recommended (> 76.0 MHz)
other load capacitances possible, see supplementary document
current max.
3 mA
low level max.
0.1 x VDC
high level min. 0.9 x VDC
standby function (e/d)
stop (S), tristate-only (T) or none (N), see table 3
output enable time max.
5 ms (S) / 150 ns (T)
output disable time max.
150 ns
start-up time max.
5 ms
standby current max.
3 µA (for stop (S), see table 3)
phase jitter 12 kHz ~ 20 MHz
< 3.0 ps RMS
symmetry at 0.5 x VDC
45% ~ 55% (standard)
current at load
5 pF
15 pF
30 pF
60 pF
unit
output disabled
4.0
4.0
4.0
4.0
mA
1.0 ~ 19.9 MHz
4.0
4.6
5.6
7.6
mA
20.0 ~ 29.9 MHz
4.6
5.7
7.4
10.9
mA
30.0 ~ 49.9 MHz
5.1
6.7
9.2
14.3
mA
50.0 ~ 79.9 MHz
6.4
9.0
13.2
mA
80.0 ~ 110.0 MHz
7.7
11.2
17.0
mA
115.0 ~ 137.0 MHz
(10.0)
(14.5)
mA
note: current at default edge control setting “D”, also refer to table 4.
Table 3: Configurable Standby Function Options (e/d)
note: some frequencies can’t be configured, see table 5.
pin #1 (e/d control)
option
functionality
low “0” (VIL ≤ 0.2 VDC)
S = Stop
output weakly pulled down, oscillator in sleep mode
T = TriState
output high impedance, oscillator operates
N = None
oscillator output active
high “1” (VIH ≥ 0.8 VDC)
all
oscillator output active
open*
all
oscillator output active
* a pull up resistor is recommended in EMI stressed circuit environments.
Packing Note / Marking
Pin Connection
QTY < 250 pcs. ➝ cut tape
QTY 250/500/1K/3K pcs. ➝ tape and reel
Marking: lot code only
#4
#3
#1
#2
# 4: VDC
# 3: output
# 1: e/d
# 2: GND
note: a capacitor of 0.1 µF between VDC and GND is recommended.
RoHS
2011/65/EC
RoHS compliant
Pb free
REACH compliant
Conflict mineral free
Jauch MEMS – Uses SiTime’s MEMS First™ technology
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
081214
MEMS-Oscillator · JSO LC series · 2.5 V ~ 3.3 V
Table 4: Max. Rise & Fall Time vs. Load Capacitance
CL
5 pF
edge control
15 pF
30 pF
5 pF
at 10% ~ 90% of VDC (ns)
15 pF
30 pF
at 20% ~ 80% of VDC (ns)
Table 5: Non-Configurable Frequencies
operating temperature option
operating temperature option
T2 − (-40°C ~ +105°C)
T8 − (-55°C ~ +125°C)
0
1.2
2.4
5.2
0.8
1.7
3.4
T3 − (-40°C ~ +125°C)
1
1.4
2.6
5.8
0.9
1.9
3.8
from (MHz)
to (MHz)
from (MHz)
to (MHz)
2
1.6
3.0
6.0
1.1
2.1
4.0
61.223
61.674
61.223
61.974
D = 3*
1.8
4.0
6.6
1.2
2.6
4.6
69.796
70.485
69.240
70.827
4
3.2
6.4
11.0
2.2
4.4
7.8
79.063
79.162
78.715
79.561
5
4.4
8.4
14.6
2.9
5.8
10.4
81.428
82.232
80.160
80.174
6
6.6
12.4
23.0
4.4
8.6
15.2
91.834
92.155
80.780
82.632
7
12.8
25.0
46.0
8.6
16.6
30.0
94.249
94.430
91.834
95.474
94.875
94.994
96.192
96.209
97.714
98.679
96.936
99.158
110.0
115.194
110.0
119.342
117.811
118.038
–
–
118.594
118.743
120.239
120.262
122.142
122.705
121.170
121.243
123.022
123.348
121.601
123.948
* default edge control setting “D” at VDC = 2.5 V ~ 3.3 V, please also refer to the
supplementary information on our homepage for typical values and more details.
Order Information
Example:
O 26.123456 – JSO 75 C1 L C – B – 2V3 – T0 – S – D
O = Oscillator
frequency (8 digits), see also table 5
1.0 ~ 110.0 MHz
115.0 ~ 137.0 MHz
JSO = Jauch Silicon Oscillator
package
75 = 7050
53 = 5032
32 = 3225
22 = 2520
21 = 2016
frequency range
C1 = 1.0 ~ 110.0 MHz
C2 = 115.0 ~ 137.0 MHz
function/feature
L = lowpower
output I/F
C = (H)CMOS
edge control
D = default
0 – 7, see table 4
standby function options
S = Stop
T = TriState
N = None
temperature range
T0 = -20°C ~ +70°C
T1 = -40°C ~ +85°C
T2 = -40°C ~ +105°C
supply voltage
3.3 = 3.3 V
3.0 = 3.0 V
2.8 = 2.8 V
T3 = -40°C ~ +125°C
T8 = -55°C ~ +125°C
2.5 = 2.5 V
1.8 = 1.8 V
2V3 = 2.5 V ~ 3.3 V
frequency stability overall
B = ± 50 ppm
C = ± 25 ppm
G = ± 30 ppm
D = ± 20 ppm
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
MEMS-Oscillator · JSO LC series
Dimensions
#2
#1
#2
1.4
1.4
#1
#4
## 14
#1
#1
side view
bottom view
Pin connection # 1: e/d # 2: GND # 3: output # 4: VDC note: a capacitor of 0.1 µF between VDC and GND is recommended
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
5.08
1.5
0.8
0.8
0.8
0.8
1.0
1.00.8
1.0
1.2
1.0
1.0
1.2
1.2
1.6
1.2
1.2
1.6
1.6
2.0
1.6 1.2
2.0
5.08
1.5
1.6
1.5layout
pad
5.08
2.2
5.08
5.08
2.2
2.0
1.1
2.2 1.9
2.2
2.2
1.5
2.54
2.2
1.1
1.42.54
1.5
2.54
2.2
#1
1.4
1.4
2.54
1.4 layout
2.2
pad
1.6
1.9
1.42.2
2.545.08
3.81
0.7
2.6
#4
#2
2.54
2.2
1.1
1.4
2.2
1.5
5.08
#3
1.0
1.2
1.5
1.9
#1
1.15
1.1 0.7
2.2
1.1
#2
1.9
0.7
0.8
1.9
#4
1.4
top view
0.8
1.2
1.2
0.48
1.2
1.51.2
0.5
1.5
0.7
1.9
1.5
1.1
2.39
#3
0.7
1.1
2.21.4
2.0
5.08
pad layout
2.0
#2
#3
1.1 2.2
1.9
2.2
1.5
0.9
0.9
## 14
1.5
#1
##32 1.15
##14
5.08
# 2 1.15
#1
#3
#4
bottom
view
1.155.08
#2
#1
# 3 1.4 5.08
#4
## 23
0.93
1.1
#2
1.1
3.81
5.08
0.91.9
1.1
3.81
## 23
1.2
0.48
0.48
0.48 0.48 0.48
0.5
0.5
0.5
#4
bottom view
1.9
0.9 1.9
1.9
2.1
0.9
##14
##32
#2
2.39 # 1
0.9
# 3 1.152.39 # 4
#2
#1
# 3 1.152.39 # 4
# 2 1.4
#2
#3
1.5
1.9
0.9 0.9
0.75
1.1
0.8
0.8
#2
#1
1.1
0.8 0.9
#3
0.8
#1
0.9
7.0±0.05
#4
#4
#2
0.90±0.10
0.9
3.2±0.05
#2
0.9
#1
#3
5.0±0.05
#4
#3
1.1
5.0±0.05
#1
1.00
0.75±0.05
0.9
1.1
1.1
2.5
#2
#1
##33 bottom view##44
2.1
0.75
#2
#1
# 3 0.75
#4
2.1 ##11
##22
0.75
# 3 0.9 2.1 # 4
#2
#1
#3
2.1 # 4
0.9
2.39
# 23
# 14
# 3 0.9
#4
#2
2.39 # 1
#2
0.68
0.5
#4
#1
#4
#4
0.5
0.7
0.75±0.05
0.75±0.05
## 14
#1
#3
1.1
#2
#1
#4
#4
#1
0.75±0.05
±0.05
#1
±0.05
#3
##320.68
# 2 1.00
0.68
# 30.751.00
#2
# 30.751.00
2.1
#4
pad
1.5
0.9 layout
1.5
0.65
1.1
0.93
0.93
1.6
1.1
0.93 0.93 0.93
±0.05
1.1
2.0
1.1
3.2±0.05
#4
0.8
3.2
#2
# 30.680.65
1.00
#2
#3
#3
0.68
# 2 1.00
1.5
0.9
2.2
2.0
#1
#1
0.68
# 3 0.65 # 4
# 2 bottom view
#1
1.5
3.81 3.81 3.81
## 23
#3
#4
0.65 # 1
1.1
## 14
#3
#2
#4
1.1
#1
#2
# 4 7.0±0.05 # 3
side view
#4
0.65
1.5
1.1
7.0 x 5.0 x 0.90
JSO75
##23
7.0±0.05
#1
#2
#4
#3
top7.0
view
±0.05
#1
#2
# 4 7.0±0.05 # 3
2.5±0.05
2.6
# 41
#1 #2
2.6
## 14 7.0±0.05## 23
3.2
# 4 5.0±0.05# 3
#1
#2
# 4 5.0±0.05# 3
side view
3.2
5.0 x 3.2 x 0.75
JSO53
5.0±0.055.0±0.05 5.0±0.05 5.0±0.05 5.0±0.053.2
##23
# 41
# 1 5.0±0.05# 2
±0.05
top view
±0.05
# 43.2±0.05# 3
#1
#2
# 43.2±0.05# 3
5.0±0.05
## 14
## 23
#4
#3
# 1 5.0±0.05# 2
side view
±0.05
3.2 x 2.5 x 0.75
JSO32
# 1top view
#2
# 4 # #3 3
3.2±0.05
#1 #2
#4
#3
±0.05
## 113.2 # #2 2
#4 #3
2.6
# 42.5±0.05
#3
#1 #2
±0.05
# 42.5
#3
3.2±0.05
2.0±0.05
2.6
## 41 ##23
# 12.5±0.05
#2
±0.05
2.5 x 2.0 x 0.75
JSO22
# 2.0
4 ±0.05
#3
2.5±0.05
#1 #2
#4 #3
#4 #3
# 12.5±0.05
#2
side view
#3
2.6
# 2.0
4 ±0.05
#3
# 1top #view
2
±0.05
#4 #3
# 2.0
1 ±0.05
#2
±0.05
±0.05
0.90±0.100.90±0.100.90±0.10 0.90±0.10 0.90±0.100.75 0.75 0.75
#4 #3
2.0±0.05
±0.05
±0.05
±0.050.75±0.05 0.75±0.05 0.75
±0.05
0.75±0.050.75±0.05 0.75±0.05 0.75±0.05
0.75
0.75
±0.05 0.75
0.75±0.050.75±0.050.75±0.05 0.75±0.05 0.75
0.75±0.05 0.75±0.05
0.65
±0.05 1.6±0.05
±0.05
1.6±0.05 1.6±0.05
±0.05 1.6
±0.052.0±0.05 2.0±0.05
2.0±0.05 2.01.6
2.0±0.05
±0.052.5±0.05 2.5±0.05
2.5±0.05 2.5
2.5
3.2
2.0±0.05
±0.05
2.0 x 1.6 x 0.75
JSO21
2.2
2.2
pad layout
in mm
ø 1.0±0.1
4.0±0.1
2.25±0.05
ø 1.0±0.1
Direction of feed
1.5 min.
1.1±0.1
2.0±0.1
ø 1.5±0.1
ø 1.5±0.1
ø 1.5±0.1
4.0±0.1
2.7±0.1
ø 1.5±0.1
Direction of feed
Direction of feed
Direction of feed
4.0±0.1
2.7±0.1
ø 1.5±0.1
Direction of feed
1.5 min.
1.5 min.
up to 3000 pcs per reel
ø 1.5±0.1
ø 1.5±0.1
ø 1.5±0.1
8.0±0.1
3.5±0.1
ø 1.5±0.1
8.0±0.1
3.5±0.1
ø 1.5±0.1
4.0±0.1
4.0±0.1
4.0±0.1
2.0±0.1
2.0±0.1
2.0±0.1
4.0±0.1
2.0±0.1
4.0±0.1
2.0±0.1
8.0±0.1
8.0±0.1
8.0±0.1
5.4±0.1
5.4±0.1
5.4±0.1
ø 1.5±0.1
ø 1.5±0.1
ø 1.5±0.1
8.0±0.1
5.4±0.1
ø
1.5±0.1
8.0±0.1
5.4±0.1
ø 1.5±0.1
Direction of feed
Direction of feed
Direction of feed
1.5 min.
0.3±0.05
0.3±0.05
0.3±0.05
0.3±0.05
0.3±0.05
1.3±0.1
1.3±0.1
1.3±0.1
12.4+2.0/-0
12.4+2.0/-0
Ø 180: up to 1000 pcs per reel
ØØ 330:
180: up
up to
to 3000
1000 pcs
pcs per
per reel
reel
330: up
up to
to 1000
3000 pcs
pcs per
per reel
reel
ØØ 180:
Ø 330: up to 3000 pcs per reel
Ø 180: up to 1000 pcs per reel
Ø 330: up to 3000 pcs per reel
+2.0/-0
Ø 180: 16.4
up to 1000 pcs per reel
Ø 330: 16.4
up to+2.0/-0
3000 pcs per reel
16.4+2.0/-0
1.1±0.1
Direction of feed
Direction of feed
1.5 min.
1.1±0.1
Direction of feed
Direction of feed
Direction of feed
Direction of feed
1.1±0.1
1.1±0.1
1.1±0.1
1.5 min.
120°
1.5 min.
1.5 min.
120°
ø 50
3.5±0.1
3.5±0.1
3.5±0.1
0.3±0.05
ø 21 ø 21 ø 21 ø 21
8.0±0.1
8.0±0.1
8.0±0.1
0.3±0.05
ø 21
2.0±0.1
12.4pcs per reel
up to 3000
12.4+2.0/-0
12.4+2.0/-0
120°
120°
120°
1.5 min.
ø 21 ø 21 ø 21 ø 21
4.0±0.1
0.3±0.05
0.3±0.05
0.3±0.05
120°
120°
120°
1.5 min.
ø 21
2.0±0.1
8.4 +1.5/-0
+2.0/-0
12.3 max.
12.3 max.
12.312.3
max.12.3
max.max.
4.0±0.1
1.75±0.11.75±0.11.75±0.1
1.75±0.1
1.75±0.1
2.0±0.1
2.0±0.1
2.0±0.1
7.25±0.17.25±0.17.25±0.1
7.25±0.1
7.25±0.1
4.0±0.1
4.0±0.1
4.0±0.1
8.4 +1.5/-0
up to 3000 pcs per reel
up to 3000 pcs per reel
up to 3000 pcs per reel
1.15 ±0.1
1.15 ±0.1
16.0±0.316.0±0.316.0±0.3
16.0±0.3
16.0±0.3
7.4±0.1 7.4±0.1 7.4±0.1
7.4±0.1
7.4±0.1
7.0 x 5.0 x 0.90
JSO75
0.2±0.05±0.1
1.15
1.15 ±0.1
1.15 ±0.1
Direction of feed
1.75±0.11.75±0.11.75±0.1
1.75±0.1
1.75±0.1
5.3±0.1 5.3±0.1 5.3±0.1
5.3±0.1
5.3±0.1
5.0 x 3.2 x 0.75
JSO53
0.2±0.05
1.5 min.
120°
1.5 min.
1.5 min.
120°
ø 60
2.7±0.1
2.7±0.1
2.7±0.1
8.4pcs per reel
up to 3000
8.4 +1.5/-0
8.4 +1.5/-0
ø 21 ø 21 ø 21 ø 21
4.0±0.1
4.0±0.1
4.0±0.1
0.2±0.05
0.2±0.05
0.2±0.05
120°
120°
120°
ø 21
4.0±0.1
ø 180.5 ø 180.5ø 180.5
ø 180.5
ø 180.5
up to 3000 pcs per reel
+1.5/-0
8.3 max.8.3 max.
8.3 max.
8.3 max.
8.3 max.
2.0±0.1
5.25±0.15.25±0.15.25±0.1
5.25±0.1
5.25±0.1
4.0±0.1
1.75±0.11.75±0.11.75±0.1
1.75±0.1
1.75±0.1
2.0±0.1
2.0±0.1
2.0±0.1
9.25±0.19.25±0.19.25±0.1
9.25±0.1
9.25±0.1
3.8±0.1 3.8±0.1 3.8±0.1
3.8±0.1
3.8±0.1
4.0±0.1
4.0±0.1
4.0±0.1
ø 13 ø 13 ø 13 ø 13
up to 3000 pcs per reel
up to 3000 pcs per reel
up to 3000 pcs per reel
1.1±0.1
Direction of feed
3.2 x 2.5 x 0.75
JSO32
ø 180.5 ø 180.5ø 180.5
ø 180.5
ø 180.5
2.25±0.05
1.5 min.
ø 180.5 ø 180.5ø 180.5
ø 180.5
ø 180.5
4.0±0.1
Direction of feed
Direction of feed
Direction of feed
0.3±0.05±0.1
1.1
1.1±0.1
1.1±0.1
8.4 +1.5/-0
1.5 min.
120°
1.5 min.
1.5 min.
120°
1.3±0.1
1.3±0.1
Direction of feed
Jauch Quartz GmbH • e-mail: [email protected]
full data can be found under: www.jauch.de / www.jauch.co.uk / www.jauch.fr / www.jauchusa.com
All specifications are subject to change without notice
ø 180/330
ø 180/330
ø 180/330
ø 180/330
ø 180/330
2.0±0.1
ø 1.0±0.1
ø 1.0±0.1
ø 1.0±0.1
8.4 +1.5/-0
16.4+2.0/-0
ø 180/330
ø 180/330
ø 180/330
ø 180/330
ø 180/330
2.25±0.05
2.25±0.05
2.25±0.05
1.5 min.
120°
1.5 min.
1.5 min.
120°
ø 60
4.0±0.1
4.0±0.1
4.0±0.1
0.3±0.05
ø 21 ø 21 ø 21 ø 21
4.0±0.1
0.3±0.05
0.3±0.05
0.3±0.05
120°
120°
120°
ø 21
2.0±0.1
8.4pcs per reel
up to 3000
8.4 +1.5/-0
8.4 +1.5/-0
+1.5/-0
8.3 max.8.3 max.
8.3 max.
8.3 max.
8.3 max.
4.0±0.1
5.25±0.15.25±0.15.25±0.1
5.25±0.1
5.25±0.1
2.0±0.1
2.0±0.1
2.0±0.1
1.75±0.11.75±0.11.75±0.1
1.75±0.1
1.75±0.1
2.8±0.1 2.8±0.1 2.8±0.1
2.8±0.1
2.8±0.1
4.0±0.1
4.0±0.1
4.0±0.1
ø 60 ø 60 ø 60 ø 60
up to 3000 pcs per reel
Direction of feed
2.5 x 2.0 x 0.75
JSO22
ø 13
ø 60
1.0±0.1
ø 13 ø 13 ø 13 ø 13
Direction of feed
ø 60 ø 60 ø 60 ø 60
ø 1.0±0.1
ø 13
1.9±0.05
ø 13 ø 13 ø 13 ø 13
4.0±0.1
up to 3000 pcs per reel
up to 3000 pcs per reel
up to 3000 pcs per reel
1.0±0.1
ø 60 ø 60 ø 60 ø 60
ø 1.0±0.1
1.5 min.
ø 13
1.9±0.05
1.5 min.
ø 13 ø 13 ø 13 ø 13
4.0±0.1
Direction of feed
Direction of feed
Direction of feed
0.3±0.05±0.1
1.0
1.0±0.1
1.0±0.1
ø 50 ø 50 ø 50 ø 50
2.0±0.1
ø 1.0±0.1
±0.1
ø 1.0
ø 1.0±0.1
ø 13
1.9±0.05
1.9±0.05
1.9±0.05
ø 13 ø 13 ø 13 ø 13
4.0±0.1
4.0±0.1
4.0±0.1
8.4 +1.5/-0
ø 50 ø 50 ø 50 ø 50
4.0±0.1
0.3±0.05
8.4 +1.5/-0
16.4+2.0/-0
ø 13
2.0±0.1
1.5 min.
120°
1.5 min.
1.5 min.
120°
Ø 180: up to 1000 pcs per reel
330: up
up to
to 1000
3000 pcs
pcs per
per reel
reel
ØØ 180:
ØØ 330:
180: up
up to
to 3000
1000 pcs
pcs per
per reel
reel
Ø 330: up to 3000 pcs in
permm
reel
Ø 180: up to 1000 pcs per reel
Ø 330: up to 3000 pcs per reel
Ø 180: up to 1000 pcs per reel
Ø 330: up to 3000 pcs per reel
ø 50
4.0±0.1
8.4 +1.5/-0
8.4 +1.5/-0
8.4 +1.5/-0
ø 21 ø 21 ø 21 ø 21
2.3±0.1 2.3±0.1 2.3±0.1
2.3±0.1
2.3±0.1
2.0 x 1.6 x 0.75
JSO21
0.3±0.05
0.3±0.05
0.3±0.05
120°
120°
120°
ø 21
2.0±0.1
2.0±0.1
2.0±0.1
±0.1
8.3 max.8.3 max.
8.3 max.
8.3 max.
8.3 max.
4.0±0.1
4.0±0.1
5.25±0.15.25±0.15.25±0.1
5.25±0.1
5.25±0.1
Taping Specification
4.0
1.75±0.11.75±0.11.75±0.1
1.75±0.1
1.75±0.1
MEMS-Oscillator · JSO LC series
PRODUCTS IN TOP QUALITY
QUARTZ CRYSTALS
QUARTZ CRYSTAL OSCILLATORS
MEMS OSCILLATORS
n
Inhouse R & D center
n
Technical customer support by field application engineers
n
Excellent product availability with over 28 million components in stock
n
Standard and customized quartz crystal and MEMS products
n
Worldwide presence expert advice by quartz crystal specialists
GI34 | kms-wirkt.de
RELIABLE SOLUTIONS
FOR ELECTRONIC
APPLICATIONS
Jauch Quartz GmbH
78056 VS -Schwenningen
Germany
www.jauch.de
Jauch Quartz GmbH
4435 Niederdorf
Switzerland
www.jauch.de
n
Consumer electronics
n
Medical applications
n
Industrial applications
n
Telecommunication
n
Avionics, space & military applications
n
Solar technology applications n
Energy saving applications
Jauch Quartz France
92100 Boulogne-Billancourt
France
www.jauch.fr
Jauch Quartz UK Ltd.
Camberley, Surrey, GU15 3YX
United Kingdom
www.jauch.co.uk
Jauch Quartz America, Inc.
Seabeck, WA 98380
USA
www.jauchusa.com