IR3M92N4

IR3M92N4
IR3M92N4
Application note
Contents
1.
2.
3.
4.
5.
6.
6.1
6.2
6.3
6.4
7.
7.1
7.2
7.3
7.4
7.5
7.6
7.7
8.
8.1
8.2
8.3
8.4
9.
9.1
9.2
9.3
9.4
9.5
10.
10.1
10.2
10.3
10.4
10.5
11.
General description
Pin assignment and Package outline
Pin description
Absolute maximum ratings
Electrical characteristics
Operation mode description
Critical Current Mode operation
Power factor improvement operation
Quasi-resonant operation
Constant Current Output Operation
Block description inside the IC
Start up circuit (VCC)
Switching circuit (OUT)
ON timing detecting circuit (VSE)
Peak current detecting circuit (ISE)
Multiplier (FL1)
Error amplifier circuit (FL2)
Mode detection circuit (FUNC)
Setting operation mode
Flyback mode
Non-insulated mode (step up)
Non-insulated mode (step down)
PWM Dimmer function
Protection Function
Soft start function
Over temperature protection
VCC under voltage lock-out
Output over voltage lock-out
FET over current protection
External circuit example
Transformer
FET
Snubber circuit
Filter circuit
Output capacitor
Notes on Contents
Sheet No.: OP13026EN
Attachment-1
IR3M92N4
1. General description
IR3M92N4 is a controller IC of LED Lighting power supply.
Operation mode is Critical Current Mode. It can enable high power factor by controlling ON period constant,
and enable high efficiency and low EMI by quasi-resonant operation.
Either insulated or non-insulated circuit is capable in accordance with the purpose.
Insulated circuit uses flyback converter method, and is able to control in high power factor and high accuracy.
Non-insulated circuit uses step up or step down converter method with transformer, and is able to control
in high power factor, high accuracy and high efficiency. In comparison with insulated circuit, non-insulated
circuit can smaller the size and lower the price of the power system by decreasing external components.
2. Pin assignment and Package outline
①
②
③
④
⑤
⑥
⑦
⑧
OUT
GND
ISE
VSE
FL1
FL2
FUNC
VCC
Sheet No.: OP13026EN
Attachment-1
IR3M92N4
3. Pin description
Pin name
Pin description
1. OUT
Gate drive for the external switching MOSFET
2. GND
Ground pin
3. ISE
Current sense of the primary winding
4. VSE
Voltage sense of the auxiliary winding
5. FL1
The input pin of error amplifier.
6. FL2
The output pin of error amplifier.
7. FUNC
Mode detection pin
8. VCC
Power supply pin
4. Absolute maximum ratings
Absolute maximum ratings are values or ranges which can cause permanent damage.
Please do not exceed this range even when start up or shut down.
Ta=25°C
Parameter
Symbol
Rating
Unit
Applied terminal
Power Supply Voltage
Vcc
-0.3 ~ 28.0
V
VCC
Input Terminal Voltage
VI1
-0.3 ~ 6.0
V
ISE, VSE, FL1,FL2,FUNC
Output Terminal Voltage
VO1
-0.3 ~ 28.0
V
OUT
Operating Temperature
TOPR
-30 ~ 100
°C
Storage Temperature
TSTG
-40 ~ 150
°C
Sheet No.: OP13026EN
Attachment-2
IR3M92N4
5. Electrical characteristics
Parameter
Unless otherwise specified, condition shall be GND=ISE=VSE=0V, VCC=12V, Ta=25°C
Symbol
Min. Typ.
Max. Unit
Conditions
VCC section
VCC Input Voltage
VCC1
10
12
18
V
VCC Startup Current
ICC1
―
30
80
uA
VCC Operating supply current
ICC2
―
1.0
2.0
mA
VCC Turn on threshold
Vst
15.5
18.0
20.0
V
VCC Turn off threshold
Vuvlo
5.0
6.0
7.5
V
Output Low Resistance
RL
―
―
15
Ω
OUT - 0.1V
Output High Current
IOH
40
―
―
mA
OUT < 8V
fosc
135
210
300
kHz
FL2=2.5V
Reference Voltage
VREF
2.94
3.00
3.06
V
Feedback Voltage
VFB
873
900
927
mV
Transconductance
Gm
―
43
―
uA/V
FL2 Operating range
Vfl2
0.5
―
4.0
V
VVSE
0.2
0.3
0.4
V
Threshold Voltage of
Flyback mode
VFLY
3.2
―
4.5
V
Threshold Voltage of
StepDown mode
VStepD
1.45
―
2.85
V
Threshold Voltage of
Stanby mode
Vstby
―
―
0.8
V
Threshold High Voltage of PWM
VPWMH
1.45
―
4.50
V
Threshold Low Voltage of PWM
VPWML
―
―
0.8
V
IFUNC
8.7
10.0
12.5
uA
VOCP_FLY
1.45
1.60
1.75
V
FL2=2.5V
VOCP_StepD
0.65
0.80
0.95
V
FL2=2.5V
Minimum Off Time in OCP
tmin
40
70
120
us
Leading edge blanking time
tleb1
―
200
―
ns
Threshold Voltage of VSE
VOVP_VSE
1.9
2.1
2.3
V
Threshold Voltage of VCC
VOVP_VCC
22
23
24
V
Leading edge blanking time
tleb2
―
600
―
ns
TSD
135
150
165
°C
VCC=Startup voltage - 0.1V
Gate driver section
Oscillator section
Frequency
Error Amplifier Section
(※)
VSE=1V,ISE=0.3V,FL2=2.5V
FL1=0.9V
Zero Cross Detect Section
VSE Threshold Voltage
FL2=2.5V
FUNC section
FUNC Bias Current
Over Current Protection Section
Threshold Voltage of Flyback
Threshold Voltage of StepDown
Over Voltage Protection Section
Over Temperature Protection Section
Threshold Temperature
Junction temperature, (※)
(※) It is secured by the design and the test is not done.
Sheet No.: OP13026EN
Attachment-3
IR3M92N4
6. Operation mode description
6.1 Critical Current Mode operation
When using insulated flyback converter method, this IC will operate in Critical Current Mode by detecting
the timing when the secondary inductor’s current becomes 0mA, and turn on the FET.
When using non-insulated step up converter, step down converter, or choke coil method, this IC will
operate in Critical Current Mode by detecting the timing when the primary inductor’s current becomes 0mA,
and turn on the FET.
Primary current
Secondary current
None current
FET
ON
OFF
ON
OFF
Fig.1　Critical Current Mode operation
Sheet No.: OP13026EN
Attachment-4
IR3M92N4
6.2 Power factor improvement operation
ON period will become almost constant by error amplifier controlling.
Since ON period is constant, peak current of inductor will vary in proportion with input voltage.
Therefore input current varies in accordance with input voltage, and the power factor will improve.
di(t) = v(t)* dt／L ---- Peak current of inductor is proportional with input voltage, when ON period is the same.
Primary current
ＶＩＮ（ＡＣ）
ＩＩＮ（ＡＣ）
ON
FET
OFF
Fig.2 Improvement of power factor by constant ON time operation.
6.3 Quasi-resonant operation
This IC will drive the FET by Critical Current Mode, which detect the timing when the current of inductor
becomes 0mA and turn on the FET.
When it is not Critical Current Mode, as shown in figure 3, after releasing all the energy of inductor the
inductance of primary transformer and the parasitic capacitance will cause ringing at the drain of FET,
and spread EMI around the circuit.
When it is Critical Current Mode, the VSE terminal monitors the timing when inductor release all the
energy and turn on FET almost at the bottom point of ringing waveform, which is called quasi-resonant
operation. Therefore it can minimize the noise of EMI to spread around the circuit.
FET ON
FET OFF
FET ON
FET OFF
Ringing period
Fig.3 Waveform of FET drain (Not Critical Current Mode)
FET OFF
FET ON
FET OFF
FET ON
FET OFF
Fig.4 Waveform of FET drain (Critical Current Mode)
Sheet No.: OP13026EN
Attachment-5
IR3M92N4
6.4 Constant Current Output Operation
When it is insulated flyback converter, constant current output is enabled only by using primary
current control, without using feedback of secondary (LED) current by Photo coupler.
As shown in figure 4, the average amount of output current (Iout) can be expressed by using peak
current of secondary current (Ipk2) and the period secondary current flows (Tres).
Iout = 1 / 2 * Ipk2 * Tres / Tc
(1)
Peak current of primary and secondary current has relation with the ratio of primary and secondary winding.
Ipk2 = Np / Ns * Ipk1
(2)
(Np=primary winding turns, Ns=secondary winding turns)
Tres/Tc can be detected by using auxiliary winding which is set in primary transformer.
Iout = 1 / 2 * Np / Ns * Ipk1 * Tres / Tc
(3)
Constant current output can be obtained also in non-insulated step up circuit.
In this circuit Ipk2=Ipk1, and will be expressed as shown below.
Iout = 1 / 2 * Ipk1 * Tres / Tc
(4)
Ｉｐｋ１
Primary current
Ｉｐｋ２
Ｉｏｕｔ
Secondary current
Ｔｒｅｓ
Ｔｃ
Ｉｏｕｔ＝１／２＊Ｉｐｋ２＊Ｔｒｅｓ／Ｔｃ
Fig.5　Constant current output control
In case of non-insulated step down method as well as step up method, Ipk2=Ipk1.
If you set Tres/Tc=1, the average amount of output current (Iout) can be expressed as below.
Please refer to figure.6
Iout = 1 / 2 * Ipk1
(5)
Ｉｐｋ１=Ipk2
Ｉｏｕｔ
Primary current
(Secondary current)
Ｉｏｕｔ＝１／２＊Ｉｐｋ1
Fig.6 Constant current output control
Sheet No.: OP13026EN
Attachment-6
IR3M92N4
7. Block description inside the IC
7.1 Start up circuit (VCC)
FET starts switching when VCC reaches up to start up voltage Vstart=Typ.18V.
After turning on AC voltage, current is supplied to Cvcc from VIN through Rstart, and VCC voltage rises.
Tstart, which is the time for VCC to reach start up voltage can be expressed as shown below.
Tstart = Cvcc * Vstart / ( I1 - I2 )
(6)
I2 is current consumed in IC. I1 is current supplied from VIN through Rstart. I1 can be expressed as
shown below.
I1 = ( VIN - VCC ) / Rstart
Equation (10) can be expressed as shown below, using the equation above.
Tstart = Cvcc * Vstart / (( VIN - VCC ) / Rstart - I2 )
(7)
And the loss at Rstart is expressed as shown below.
Rstart Loss = ( VIN - VCC ) ^ 2 / Rstart
(8)
When, Vstart=18V, VCC=18V, I2=30uA, C2=10uF, Rstart=300kΩ, VIN=100V
T = 10uF * 20V / (( 100V - 20V ) / 300kΩ - 30uA )
= 0.85s
Rstart Loss = ( 100 - 17.8 ) ^ 2 / 300kΩ
= 23mW
Rstart should be smaller to speed up start-up sequence, but it has demerit of larger loss.
ＢＤ
VIN
L1
Ｄ３
Ｒｓｔａｒｔ
Ｃ２
Ｒ１３
Ｃ４
Ｌｐ
Ｌｓ
Ｒ２０
Ｃｏｕｔ
LED
Ｄ４
Ｉ１＝（ＶＩＮ－ＶＣＣ)／Ｒｓｔａｒｔ
FET
Leak current before start-up
Ｉ２＝30uA（typ）
Ｃｖｃｃ
Ｒｃｓ
VCC
5V
Regulator
Start-up timel ＝
ＣＶｃｃ＊Ｖｓｔａｒｔ／（（ＶＩＮ－ＶＣＣ）／ＲＳｔａｒｔ―Ｉ２）
+
-
+
ＳｔａｒｔＵｐ
18V
ＵＶＬＯ
6V
Fig.7 Start-up time
Sheet No.: OP13026EN
Attachment-7
IR3M92N4
The capacitor connected to VCC must be a sufficient value, since it must keep VCC over UVLO voltage until
feedback voltage from auxiliary winding (VAUX) reaches up to UVLO voltage (6V (Typ.)),
UVLO6V < VCC = ( VAUX - VD2 ) = ( Na / Ns ) * ( VLED - VD3 )
(9)
where VD2 is voltage drop of diode D2, and VD3 is voltage drop of diode D3.
ＶＤ３
ＢＤ
Ｎａ／Ｎｓ
VIN
ＶＬＥＤ
Ｄ３
L1
C２
Rｓｔａｒｔ
Ｒ１３
C４
Ｌｐ
ＶＤ２
Ｒ３
Ｃｖｃｃ
Ｄ２
Ｌｓ
Ｒ２０
Ｃｏｕｔ
ＬＥＤ
Ｄ４
AUX
ＶＡＵＸ FET
Ｒｏｖｐ１
Ｌａ
Ｒｃｓ
Ｒｏｖｐ２
VCC
5V
Regulator
+
-
+
ＳｔａｒｔＵｐ
18V
ＵＶＬＯ
6V
Fig.8 VCC power supply circuit from auxiliary winding
Sheet No.: OP13026EN
Attachment-8
IR3M92N4
7.2 Switching circuit (OUT)
Connect the Gate of FET to OUT terminal.
When VSE goes down to 0.3V or less, FET turns on after 200ns (Typ.) delay time. The period FET is
on is the sum of the time in accordance with output voltage (FL2) of error amplifier (EAMP) and
200ns (Typ.) delay time.
ＢＤ
VIN
Ｄ３
L1
Rｓｔａｒｔ
C２
Ｒ１３
C４
Ｌｐ
Ｃｖｃｃ
Ｒ２０
Ｃｏｕｔ
ＬＥＤ
Ｄ４
VCC
VCC
5V
Regulator
Ｌｓ
3V
Regulator
DRV
Turn on ＦＥＴ
OUT
FET
Turn off ＦＥＴ
OCP
+
-
AMP
ISE
+
-
Ｒｃｓ
1.6V
Peak Hold
Voltage of FL2 set
ON period
5V
VCC
+
200ns
Ramp up
Ｄ２
Ｒｏｖｐ１
Ibias
Delay
Ｒ３
Detect VSE goes
down below 0.3V.
Q
S
R
VSE
+
Ｌａ
Ｒｏｖｐ２
2.66pF
0.3V
EAMP
+
Multiplier
OVP
+
2.1V
0.9V
Logic signal
Analog signal
FL2
CFL2
GND
FL1
CFL1
Fig.9 FET switching circuit (OUT)
FET ON timing = 200ns after VSE terminal goes down to 0.3V.
FET ON period = period in accordance with FL2 + delay time 200ns.
※The period in accordance with FL2 can be referred in “7.6 Error Amplifier (FL2)”.
Sheet No.: OP13026EN
Attachment-9
IR3M92N4
7.3 ON timing detecting circuit (VSE)
When FET turns off, the drain voltage of FET rises, and voltage in accordance with the winding turns ratio
arise at secondary and auxiliary windings. Since current of LED starts to flow when secondary winding
voltage goes up to VLED + VD3, the voltage of auxiliary winding can be expressed as
( VLED + VD3 ) * Na / Np
When secondary current goes down to 0mA, the voltage of secondary winding and auxiliary winding
decreases. VSE terminal has two purpose. First to detect the voltage decrease of auxiliary winding, to indicate
the next ON timing. And second to measure the period that current flows at secondary winding (Tres).
When VSE goes down to 0.3V or less, after 600ns (Typ.) period of leading edge blanking from the FET OFF
timing, FET turns on. Leading edge blanking period is made to mask the period until the VSE voltage
stabilizes after FET off.
Actually there is error time (ΔT). After secondary winding current becomes 0mA, VSE terminal voltage
starts decrease. The period between the starting timing of VSE decrease and the timing VSE terminal
crossing down to 0.3V is error time (ΔT). Therefore error occurs in output current control.
Iout = 1 / 2 * Np / Ns * Ipk1* ( Tres + ΔT ) / Tc
( 10 )
OUT
Primary curent
Secondary current
ΔT
Error of Tres
Tres
Ｔｃ
VSE
0.3V
ＬＥＢ（ＶＳＥ）
600ns
600ns
Fig.10 VSE waveform
Sheet No.: OP13026EN
Attachment-10
IR3M92N4
When FET turns ON, voltage arise in secondary and auxiliary winding in accordance with primary winding
voltage and winding turns ratio. Negative voltage of - VIN * Ns / Np arise at auxiliary winding.
When there is no prevention, negative voltage of - VIN * Ns / Np * Rovp2 / ( Rovp1 + Rovp2 ) arise
at VSE terminal. But there is a function to reduce the negative voltage near GND level by shorting VSE
and GND with a switch inside the IC.
At either of the condition shown below, VSE and GND shorting switch turns on.
1. OUT = Hi
2. Leading Edge Blanking (LED) = Lo and VSE < 0.3.
At the condition shown below, VSE and GND shorting switch turns off.
1. OUT = Lo and VSE > 0.3V
ＶＩＮ
Short VSE-GND by SW and minimize the negative voltage of VSE
ON：ＯＵＴ＝Ｈｉ　ｏｒ　（ＶＳＥ＜０．３Ｖ　＆　ＬＥＢ＝Ｌｏ）
OFF：ＯＵＴ＝Ｌｏ　＆　ＶＳＥ＞０．３Ｖ
ＶＣＣ
Ｒ３
Ｄ２
ＶＩＮ Ｌｐ
ーＶＩＮ＊Ｎａ／Ｎｐ
Ｌｓ
ーＶＩＮ＊Ｎｓ／Ｎｐ
Ｒｏｖｐ１
Turn ON FET
ＶＳＥ
+
ＦＥＴ
Ｒｏｖｐ２
Ｌｏｇｉｃ
０．３Ｖ
Ｌａ
ＯＵＴ
ＳＷ（ＶＳＥ－ＧＮＤ）
Ｒｃｓ
ーＶＩＮ＊Ｎａ／Ｎｐ＊Ｒｏｖｐ２／（Ｒｏｖｐ１＋Ｒｏｖｐ２）
Fig.11 VSE-GND short SW
ＯＵＴ
２００ｎｓ
ＶＳＥ
２００ｎｓ
0.3V
ＬＥＢ（ＶＳＥ）
600ns
ＳＷ（ＶＳＥ－ＧＮＤ）
OFF
600ns
ON
OFF
ON
Fig.12 Waveform of VSE – GND short SW
Sheet No.: OP13026EN
Attachment-11
IR3M92N4
7.4 Peak current detecting circuit (ISE)
ISE terminal is made to detect peak current of primary winding current when FET is ON.
ISE terminal is connected to the source of FET, and current detecting resistor Rcs is connected between
the source of FET and GND. The period ISE terminal detects the peak current starts from the timing 200ns
before OUT turns off, and end at the timing OUT turns off. It holds the peak amount during the period
FET is OFF.
Ｌｐ
FET
AMP(x3)
ISE
+
Peak Hold
circuit output
Ｒｃｓ
Sampling
Fig.13 Peak detecting circuit of primary current
OUT
Primary current（ISE）
Sampling period
200ns
200ns
Peak Hold
circuit output
Fig.14 Peak detecting waveform of primary current
Sheet No.: OP13026EN
Attachment-12
IR3M92N4
7.5 Multiplier (FL1)
FL1 is an output of a Multiplier and is also input of Error Amplifier (EAMP).
The peak hold circuit output VHOLD = Ipk1 * Rcs is divided to Tres / Tc at multiplier.
VFL1 = Ipk1 * Rcs * Tres / Tc
( 11 )
When VFL1 < Vref, EAMP increase the output, and then FET ON period increase, Ipk1 increase,
and VFL1 get close to Vref.
When VFL1 > Vref, EAMP decrease the output, and then FET ON period decrease, Ipk1 decrease,
and VFL1 get close to Vref.
Therefore error amplifier (EAMP) controls VFL1 to get close to Vref.
VFL1 = Vref = Ipk1 * Rcs * Tres / Tc
Iout = 1 / 2 * Np / Ns * Ipk1 * Tres / Tc
= 1 / 2 * Np / Ns * Vref / Rcs
( 12 )
The equation above means that the three constant (Np, Ns, Rcs) set the output current (Iout).
Ｌｐ
FET
AMP
ＶＨＯＬＤ＝3*(Ｉｐｋ１＊Ｒｃｓ)
ISE
+
-
Ｒｃｓ
ＶＳＥ
EAMP
Ｉｐｋ１＊Ｒｃｓ＊Ｔｒｅｓ／Ｔｃ
+
Multiplier
+
Ｒｏｖｐ１
Ｌａ
Ｒｏｖｐ２
Ｄｕｔｙ＝Ｔｒｅｓ／ＴＣ 0.3V
ＶＲＥＦ＝0.9V
FL1
CFL1
Fig.15 Multiplier (FL1)
When it is non-insulated step up circuit, the equation will be as shown below, since Np=Ns=1.
Iout = 1 / 2 * Vref / Rcs
( 13 )
If CFL1 is a rather large value, the stable control is obtained.
But if CFL1 is too large, the overshoot of FL2 at start up will be large, and overshoot of output
current will be large.
Recommended value : 0.1uF≦CFL1≦0.47uF, CFL1≦CFL2
Sheet No.: OP13026EN
Attachment-13
IR3M92N4
7.6 Error amplifier circuit (FL2)
FL2 is an output of error amplifier (EAMP).
The voltage of FL2 terminal sets FET ON period. As shown in Fig. 18, ON period is as shown below.
ON period = 2.66pF * VFL2 / ibias
( 14 )
Variation range of VFL2 is 0.5V to 4.5V, and on period is 0.66us to 6.00us at Ibias=2uA.
Voltage of FL2 sets FET ON period.
ON period = 2.66pF * VFL2 / Ibias
+
5V
ibias
Ramp up from FET
ON timing
2.66pF
EAMP
Voltage range of FL2
0.5V – 4.5V
+
0.9V
FL1
FL2
CFL1
CFL2
Fig.16 FET ON period control by error amplifier
FET on period
6.00us
0.66us
control range
0.5V
4.5V
FL2 (voltage)
Fig.17 Relation between FL2 voltage and FET on period
As FL2 output is clamped on the maximum voltage 4.5V, on period increases no more. This limits
input AC currents when power supply voltage falls rapidly, which is brownout function.
Please decide CFL2 to make ON period constant relative to AC cycle.
If CFL2 is a rather large value, the stable control is obtained.
If CFL2 is too large, the time until LED current starts to flow will be long, when starting up.
Sheet No.: OP13026EN
Attachment-14
IR3M92N4
7.7 Mode detection circuit (FUNC)
Operational mode can be detected by FUNC pin.
FUNC pin becomes flyback mode above 3.2V.
Since the pull-up of the FUNC pin by constant current of 10uA, it becomes the flyback mode
by making a pin open.
When you use it as step down mode, please connect 200kohm between a pin and GND.
Although the resistance connected permits the accuracy of less than 5% of variation,
and less than 100 ppm/°C of temperature characteristics, it recommends the accuracy of less
than 1% of variation, and less than 100 ppm/°C of temperature characteristics.
When you use it as stanby mode, please set a terminal as GND.
* Step down operation is unidentified.
FUNC pin
Setting
Operation mode
4.5V＞FUNC＞3.2V
2.85V＞FUNC＞1.45V
0.8V＞FUNC
open
200kΩ
GND
Flyback
Stepdown
stanby
(※) It is necessary to input the voltage beyond 1.3V into the return from standby mode at FUNC terminal.
10uA
+
-
FUNCTION
S Q FlyBack
R
mode
3V
+
Stanby
mode
1V/1.3V
Mode detection time
Fig.18　Mode detection by FUNCTION pin
Sheet No.: OP13026EN
Attachment-15
IR3M92N4
8. Setting operation mode
It is possible to set various operation mode by setting terminals as below table.
Either insulated or non-insulated circuit is capable.
Insulated circuit uses flyback converter method. Non-insulated circuit uses step up or step down converter
method with transformer, Furthermore it can realize non-insulated choke coil method, and is able to make
thin power supply module without transformer, which is suitable for tube type LED lighting.
insulated / non-insulated
Mode
insulated
Terminal setting
FL1 pin
FL2 pin
FUNC pin
Flyback
0.1 ~ 1uF
0.2 ~ 2uF
OPEN
non-insulated
Stepup
0.1 ~ 1uF
0.2 ~ 2uF
OPEN
non-insulated
Stepdown
0.1 ~ 1uF
0.2 ~ 2uF
200kΩ
insulated / non-insulated
stanby
―
―
0V
※A step-up system is unidentified.
Sheet No.: OP13026EN
Attachment-16
IR3M92N4
8.1 Flyback mode
Fig. 19 shows circuit diagram of insulated flyback mode.
ＡＣ
～
Ｃ１
ＢＤ
ＶＩＮ
Ｌ１
Ｒｓｔａｒｔ
C２
Ｄ３
Ｒ２０
Ｒ１３
C４
Ｌｐ
Ｃｏｕｔ
Ｌｓ
ＬＥＤ
Ｄ４
ＶＣＣ
Ｒ３
Ｄ２
ＡＵＸ
ＯＵＴ
ＦＥＴ
Ｒｏｖｐ１
Ｃｖｃｃ
Ｌａ
ＶＳＥ
ＩＳＥ
Ｒｏｖｐ２
Ｒｃｓ
Fig.19　ＦＬＹＢＡＣＫ
8.2 Non-insulated mode (transformer : step up)
Fig. 20 shows circuit diagram of non-insulated step up mode with transformer. Snubber circuit is not
necessary and there is no loss of Lp leakage inductance in this mode compared to in flyback method.
※A step-up system is unidentified.
ＡＣ
～
Ｃ１
ＢＤ
ＶＩＮ
Ｌ１
Ｄ３
Ｒ２０
Ｒｓｔａｒｔ
C２
Ｃｏｕｔ
Ｌｐ
ＶＣＣ
Ｒ３
Ｄ２
ＡＵＸ
ＯＵＴ
ＬＥＤ
ＦＥＴ
Ｒｏｖｐ１
Ｃｖｃｃ
Ｌａ
ＶＳＥ
ＩＳＥ
Ｒｏｖｐ２
Ｒｃｓ
Fig.20 Step-up（non-insulated)
8.3 Non-insulated mode (transformer : step down)
Fig. 21 shows circuit diagram of non-insulated step-down mode with transformer. Peak current of LED
can be reduced in this mode compared to in step up mode.
ＡＣ
～
Ｃ１
ＢＤ
ＶＩＮ
Ｌ１
Ｄ３
Ｒ２０
Ｒｓｔａｒｔ
C２
ＶＣＣ
Ｒ３
Ｄ２
ＡＵＸ
Ｃｏｕｔ
ＬＥＤ
Ｌｐ
ＯＵＴ
ＦＥＴ
Ｒｏｖｐ１
Ｃｖｃｃ
ＶＳＥ
Ｌａ
Ｒｏｖｐ２
ＩＳＥ
Ｒｃｓ
Fig.21 step-down(non-insulated)
Sheet No.: OP13026EN
Attachment-17
IR3M92N4
8.4 PWM Dimmer function
LED current can be adjusted according to Duty of PWM pulse input to FUNC pin.
Please input a PWM signal after the mode judging of the 7.7th clause of operation.
In example fly back operation, High of a PWM signal is inputted after a judgment of operation by
3.2 V < FUNC < 4.5V.
Normal operation is carried out when a PWM pulse is in a high state (1.45V to 4.5V).
Switching operation is stopped when a PWM pulse is in a low state (under 0.8V).
FUNC pin setting (@1kHz)
Dimming result
Out pin : switching
4.5V ＞ FUNC ＞ 1.45V
Out pin : OFF (※2)
0.8V ＞ FUNC
(※2) In FUNC < 0.8V, the value of FL1 and FL2 is kept and the switching-on pulse is kept constant.
When a PWM function is used, please use it after are satisfactory or checking enough with the system,
since sound may occur with a transformer, a coil, etc.
AC
H : More than 2.0V
PWM
(@1kHz)
L : Less than 1.0V
OUT
（FET gate)
PWM
OUT
（FET gate)
ISE
（FET current)
2 5 W P W M
D i m m e r ＠ 1 ｋ H ｚ
1 0 0 . 0 %
9 0 . 0 %
7 0 . 0 %
6 0 . 0 %
A C 1 0 0 V
5 0 . 0 %
A C 2 3 0 V
I o
r a t i o ( ％ )
8 0 . 0 %
4 0 . 0 %
3 0 . 0 %
2 0 . 0 %
1 0 . 0 %
0 . 0 %
0
10
20
30
40
50
D u t y
60
( % )
70
80
90
100
@ 1 k H Z
Sheet No.: OP13026EN
Attachment-18
IR3M92N4
9. Protection Function
9.1 Soft start function
At start up, switching operation is performed in soft start sequence. On time and off time shown at below
table are repeated in turns until condition of StartupOK.
On timing : ISE=0.6V or Ton(Max.)=6us
Off period : Critical Current Mode operation, Toff (Min.)=12 us or more
Condition of Startup OK : VSE > 0.8V.
At stepdown mode soft start condition is as below.
On timing : ISE=0.3V or Ton(Max.)=6us
Off period : Critical Current Mode operation, Toff (Min.)=12 us or more
Condition of Startup OK : VSE > 0.8V
Mode
Soft start
Startup OK judge
Flyback
ON : ISE = 0.6V, Ton(max) = 6us
OFF : Critical Current Mode operation, Toff(min) = 12us
VSE = 0.8V
Stepdown
ON : ISE = 0.3V, Ton(max) = 6us
OFF : Critical Current Mode operation, Toff(min) = 12us
VSE = 0.8V
Toff > 12us
OUT
ISE = 0.6V
or Ton=6us
ISE
STARTUPOK detectin
VSE >0.8V
VSE
FET ON detection voltage
VSE < 20mV
Fig.22 Softstart
Sheet No.: OP13026EN
Attachment-19
IR3M92N4
9.2 Over temperature protection
When junction temperature of this IC exceeds 150°C, over temperature protection (OHP) starts to operate
and following operation is performed.
・IC shut down (OUT is Lo, shut down 3V regulator inside the IC).
・Discharge capacitor connected to FL2 (CFL2).
・Discharge capacitor connected to VCC (Cvcc).
・When VCC goes down to UVLO (Typ.6V) or less, discharge of Cvcc stops.
Fig.23 shows the fail safe circuit .
ＢＤ
VIN
Ｄ３
L1
Rｓｔａｒｔ
C２
Ｒ１３
C４
Ｌｐ
Ｃｖｃｃ
Ｌｓ
Ｒ２０
Ｃｏｕｔ
ＬＥＤ
Ｄ４
VCC
VCC
5V
Regulator
3V
Regulator
②ＯＨＰ
Fail Safe
Logic
+
-
２００ｎｓ
23V：OVP_VCC
18V：Startup
6V：UVLO
5V
VCC discharg
+
-
AMP
ＬＥＢ
①OVP_VCC&VSE
VCC discharge until VCC
reach UVLO voltage
DRV
OUT turn off
Ｒｃｓ
Peak Hold
２Ｒ
VCC
+
FET
ISE
+
-
1.6V
③OCP
(OFF time > 60us）
OUT
Ｒ３
Ｄ２
Ｒ
Ｒｏｖｐ１
2uA
Delay
3kΩ
２００ｎｓ
Q
S
R
VSE
+
Ｌａ
Ｒｏｖｐ２
2.66pF
0.3V
EAMP
+
Multiplier
FL2 discharge
1kΩ
0.9V
FL2
CFL2
GND
+
-
ＬＥＢ
OVP_VSE
FL1
CFL1
６００ｎｓ
2.1V
Logic signal
Analog signal
Fig.23　FailSafe
Sheet No.: OP13026EN
Attachment-20
IR3M92N4
9.3 VCC under voltage lock-out
IC operation stops when VCC voltage goes down to Typ.6V or less, caused by VCC voltage lowering or
short between VCC and GND.
IC operation restarts when VCC voltage goes up to Typ.18V or more (start up voltage).
ＳｔａｒｔＵｐ
（18Ｖ）
Current supplies from VIN
and VCC arise
ＶＣＣ
Start operation
ＵＶＬＯ
（6V）
Stop operation
Leak of IC
（30uA)
ＯＵＴ
Fig.24 UVLO detection sequence
9.4 Output over voltage lock-out
When over voltage error is detected, following operation is performed.
・IC shut down (OUT is Lo, shut down 3V regulator inside the IC).
・Discharge capacitor connected to FL2 (CFL2).
・Discharge capacitor connected to VCC (Cvcc).
・When VCC goes down to UVLO (Typ.6V) or less, discharge of Cvcc stops.
The fail safe circuit is as shown in Fig. 23.
Over voltage protection is masked at Leading edge blanking (LEB) period, that is 600ns (Typ.)
from the timing OUT becomes Lo (Fig. 25).
Over voltage protection is detected by VOVP_VSE ≧ 2.1V (Typ.) (15), and VOVP_VCC ≧ 22.7 (Typ.) (16).
 Ns / Na * ( R o v1p R o v2p) / R o v2p*VO
VO
V _PV S E
VO
V _PV C C
 Ns / Na * VO
V _PV C C
V _PV S E
( 15 )
( 16 )
※Vovp_vse is over voltage threshold voltage for VSE. Vovp_VCC is over voltage threshold voltage for VCC.
OVP is not
detected because
it is LEB period
ＯＵＴ
Shut down
2.1V
ＶＳＥ
ＬＥＢ（ＶＳＥ）
ＶＣＣ
ＯＶＰ(VSE)
detection
６００ｎｓ
６００ｎｓ
22.7V
ＯＶＰ(VCC)
detection
Fig.25　ＯＶＰ detection
Sheet No.: OP13026EN
Attachment-21
IR3M92N4
9.5 FET over current protection
The IC observe FET ON current, and when ISE goes up to over current threshold voltage (Vocp) or more,
over current error is detected and following operation is performed.
・OUT turns Lo and stops switching.
・IC do not shut down.
・OFF period will be more than 67us (Typ.).
The voltage of ISE terminal at over-current detection is as follows.
Mode
over-current detection volgate
Flyback
ISE ≦1.6V(Typ.)
Step-down
ISE ≦0.8V(Typ.)
Over current protection is masked at leading edge blanking (LEB) period, that is 200ns (Typ.) from the
timing OUT becomes Hi (Fig. 26).
When OCP is detected, OFF period is set to be 67us (Typ.).
200ns
ＯＵＴ
OCP is not
detected because
it is LEB period
OFF period more than 67us
ＯＣＰ is
detected
ＩＳＥ
200ns
200ns
200ns
ＬＥＢ（ＩＳＥ）
Fig.26 OCP detection
Sheet No.: OP13026EN
Attachment-22
IR3M92N4
10. External circuit example
10.1 Transformer
First you must fix the input condition of AC power source
VAC : 85V (Min.) ~ 265V (Max.)
Fix inductance of primary winding of transformer (Lp) to make ON period 6 us at the condition VAC (Min.).
Lp = VAC (Min.) * Ton / Ip
( 17 )
When duty is 50%, since AC input current is IAC = Ip / 4, Ip can be expressed as below
Ip = 4 * Pin / VAC (Min.)
( 18 )
IAC = Ip / 4
( 19 )
Ip
Ip
IAC = Io/4
OnDuty = 50%
Fig.27
Pin and Pout can be expressed as below, using conversion efficiency η
Pin = Pout / η
( 20 )
When VAC (Min.) = 85V, Ton = 6us, Pout = 6.4W, and efficiency η = 85%
Pin = 6.4W / 85% = 7.43W
Ip = 4 * 7.43W / 85V = 0.35A
Lp = 85V * 6us / 0.35A = 1.37m2H
・Primary widing
Np = VAC (Min.) * Ton (Max.) / (Ae * BT)
( 21 )
Use the larger amount between
Vin (Min.) * Ton (Max.) or Vin (Max.) * Ton (Min.)
Ae is the effective area of the core in transformer.
BT is saturation flux density.
Use EE15 core (Ae = 15mm2), calculate using saturation flux density BT = 320mT
Np = 85V * √2 * 6us / (15mm2 * 320mT)
= 150.3
Set Np more than the value above.
・Ns (Secondary winding turns)
Ns = Np * Vout / VAC (Min.)
( 22 )
When Np = 150, Vout = 35.5V, VAC (Min.) = 85V
Ns = 150 * 35.5V / 85V = 62.6
Therefore Ns = 63
・Na (Auxiliary widing turns)
Make VCC voltage more than 16V.
Na = Ns * VCC / Vout
( 23 )
=63 * 16V / 35.5V = 28.4
Therefore Na = 28
Sheet No.: OP13026EN
Attachment-23
IR3M92N4
・Winding form
Voltage change of primary winding make an effect on auxiliary winding, in accordance with magnetic
coupling strength of primary winding and auxiliary winding.
It is able to weaken magnetic coupling by changing winding form, and weaken the effect on auxiliary winding.
Winding in whole
(in same intervals)
Winding in center
Winding on one side
Strength of coupling
Fig.27 Strengh of coupling between primary winding and
auxiliary winding for each winding form of auxiliary winding.
10.2 FET
Please use FET with a sufficient margin against primary winding peak current, and drain voltage rising
at FET OFF.
When the gate of FET change from Hi to Lo, negative surge is applied to the source of FET.
Because there is parasitic capacitance between the gate and the source of FET.
OUT
FET
ＯＵＴ：Ｈｉ→Ｌｏ
Leak occurs and
malfunction
occurs.
AMP
+
-
Negative surge occurs
ISE
Ｒｃｓ
Peak Hold
C13 conpensate charge
corresponding to negative surge
Fig.28 Counter measure against negative surge
Sheet No.: OP13026EN
Attachment-24
IR3M92N4
10.3 Snubber circuit
When using insulated flyback circuit, you must consume the energy of leakage inductance caused
by imperfect magnetic coupling of transformer at the primary winding.
Inductance of imperfect
magnetic coupling
Ｌｌ
Ｄ３
The energy is
C４
consumed at
snubber circuit
Ｒ１３
Ｌｐ
Ｌｓ
Ｒ２０
Ｃｏｕｔ
ＬＥＤ
Ｄ４
Fig.29 Snubber circuit
Appropriate value of C4 and R13 is set to keep voltage jumping of the drain at low level.
ＯＵＴ
Primary current
Ｌｌ
Inductance of imperfect
magnetic coupling
Secondary
current
Ｄ３
C４
Secondary current
Current of snubber circuit
Ｒ１３
Ｌｐ
Current of
snubber circuit
Ｄ４
Current of leakage inductance flows in to
snubber circuit and the drain voltage rises.
Ｌｓ
Ｒ２０
Ｃｏｕｔ
ＬＥＤ
ISE
Ｒｃｓ
Primary
current
Drain voltage rising
Drain of FET
Fig.30 Drain voltage rising caused by leakage inductance
Sheet No.: OP13026EN
Attachment-25
IR3M92N4
10.4 Filter circuit
The value of L1 and C2 is set by EMI observation. The cut off frequency of low pass filter made
by L1 and C1 is as shown below.
fc = 1 / ( 2π √( L1 * C2 ))
( 24 )
C１
ＢＤ
L1
C２
Fig.31 LC filter
10.5 Output capacitor
A large value of output capacitor (Cout) is needed to keep output current ripple at low level.
At the condition of power factor more than 0.9, the output ripple is approximately as shown below.
Output ripple rate = Iout / 3 * Cout ^ - 0.9
( 25 )
Where Iout is output current
Ｉｏｕｔ＝1 8 0 mA、Ｖｏｕｔ＝3 5 .5 V、PF> 0 .9
Ｉｏｕｔ＝7 0 0 mA、Ｖｏｕｔ＝3 5 .5 V、PF> 0 .9
1000%
1000%
計算値
実測値
リップル
リップル
計算値
実測値
100%
10%
100%
10%
10
100
1000
Cout(uF)
10
100
1000
Cout(uF)
10000
11 Notes on Contents
1) Block Diagrams
Some of the functional blocks, circuits, or constants in the block diagram may be omitted or
simplified for explanatory purposes.
2) Equivalent Circuits
The equivalent circuit diagrams may be simplified or some parts of them may be omitted for
explanatory purposes.
3) Timing Charts
Timing charts may be simplified for explanatory purposes.
4) Application Circuits
The application circuits shown in this document are provided for reference purposes only.
Thorough evaluation is required, especially at the mass production design stage.
Sharp does not grant any license to any industrial property rights by providing these examples
of application circuits.
Sheet No.: OP13026EN
Attachment-26