Standard Products Preliminary RadHard-by-Design RHD5903 Quad Operational Amplifier Differential Outputs with Enable www.aeroflex.com/RHDseries March 4, 2014 FEATURES Single power supply operation (3.3V to 5.0V) or dual power supply operation (±1.65 to ±2.5V) Radiation performance - Total dose: >1Mrad(Si); Dose rate = 50 - 300 rads(Si)/s - ELDRS Immune - SEL Immune >100 MeV-cm2/mg - Neutron Displacement Damage >1014 neutrons/cm2 Differential Outputs Rail-to-Rail output range Enable pin to Enable/Disable amplifiers in pairs. Short Circuit Tolerant Full military temperature range Designed for aerospace and high reliability space applications Packaging – Hermetic ceramic SOIC - 20-pin, 0.30"W x 0.50" L x 0.12"Ht SOIC - Typical Weight 1.6 grams Aeroflex Plainview’s Radiation Hardness Assurance Plan is DLA Certified to MIL-PRF-38534, Appendix G. GENERAL DESCRIPTION Aeroflex’s RHD5903 is a radiation hardened, single supply, differential output, quad operational amplifier with enable in a 20-pin SOIC package. The RHD5903 design uses specific circuit topology and layout methods to mitigate total ionizing dose effects and single event latchup. These characteristics make the RHD5903 especially suited for the harsh environment encountered in Deep Space missions. It is guaranteed operational from -55°C to +125°C. Available screened in accordance with MIL-PRF-38534 Class K, the RHD5903 is ideal for demanding military and space applications. ORGANIZATION AND APPLICATION The RHD5903 amplifiers are capable of rail-to-rail outputs. Performance characteristics listed are for general purpose operational 5V CMOS amplifier applications. The amplifiers will drive substantial resistive or capacitive loads and are unity gain stable under normal conditions. Resistive loads in the low kohm range can be handled without gain derating and capacitive loads of several nF can be tolerated. CMOS device drive has a negative temperature coefficient and the devices are therefore inherently tolerant to momentary shorts, although on chip thermal shutdown is not provided. All inputs and outputs are diode protected. The devices will not latch with SEU events to above 100 MeV-cm2/mg. Total dose degradation is minimal to above 1Mrad(Si). Displacement damage environments to neutron fluence equivalents in the mid 1014 neutrons per cm2 range are readily tolerated. There is no sensitivity to low-dose rate (ELDRS) effects. SEU effects are application dependent. The RHD5903 is configured with enable/disable control. Pairs of amplifiers are put in a power-down condition with their outputs in a high impedance state. Several useful operational amplifier configurations are supported where more than one amplifier can feed an output with others disabled. SCD5903 Rev B VCC +IN_A 4 -IN_A 3 EN_AB +IN_B -IN_B +IN_C -IN_C -IN_D 2 +OUT_A 1 -OUT_A A 10 8 6 7 B 9 15 14 EN_CD +IN_D 5 +OUT_B -OUT_B 18 20 -OUT_D +OUT_A 2 19 +OUT_D -IN_A 3 18 -IN_D +IN_A 4 17 +IN_D VCC 5 16 VEE 15 +IN_C RHD5903 +OUT_C +IN_B 6 12 -OUT_C -IN_B 7 14 -IN_C 19 +OUT_D +OUT_B 8 13 +OUT_C 20 -OUT_D -OUT_B 9 12 -OUT_C EN_AB 10 11 EN_CD 11 D 1 13 C 17 -OUT_A 16 VEE FIGURE 1: BLOCK DIAGRAM 20-Pin SOIC Notes: 1. Package and Lid are electrically isolated from signal pads. 2. It is recommended that the Lid be grounded to prevent any ESD or static buildup. 3. EN_AB enables amplifiers A & B. EN_CD enables amplifiers C & D. Pin Signal Name FIGURE 2: PACKAGE PIN-OUT Definition 1 - OUT_A Negative Output of Amplifier A. 2 + OUT_A Positive Output of Amplifier A. 3 -IN_A Inverting input of Amplifier A. 4 +IN_A Non-Inverting input of Amplifier A. 5 VCC + Voltage Supply. 6 +IN_B Non-Inverting input of Amplifier B. 7 -IN_B Inverting input of Amplifier B. 8 + OUT_B Positive Output of Amplifier B. 9 - OUT_B Negative Output of Amplifier B. 10 EN_AB A Logic Low will disable Amplifiers A & B so that the outputs are high impedance. 11 EN_CD A Logic Low will disable Amplifiers C & D so that the outputs are high impedance. 12 - OUT_C Negative Output of Amplifier C. 13 + OUT_C Positive Output of Amplifier C. 14 -IN_C Inverting input of Amplifier C. 15 +IN_C Non-Inverting input of Amplifier C. 16 VEE - Voltage Supply. 17 +IN_D Non-Inverting input of Amplifier D. 18 -IN_D Inverting input of Amplifier D. 19 + OUT_D Positive Output of Amplifier D. 20 - OUT_D Negative Output of Amplifier D. TABLE 1: PIN-OUT DESCRIPTION SCD5903 Rev B Preliminary 3/4/14 2 Aeroflex Plainview ABSOLUTE MAXIMUM RATINGS Parameter Range Units Case Operating Temperature Range -55 to +125 °C Storage Temperature Range -65 to +150 °C Junction Temperature +150 °C Supply Voltage VCC - VEE +6.0 V VCC +0.4 VEE -0.4 V Lead Temperature (soldering, 10 seconds) 300 °C Thermal Resistance, Junction to Case,jc 7 °C/W 2,000 - 3,999 V 200 mW Input Voltage ESD Rating (per MIL-STD-883, Method 3015, Class 2) Power @ 25°C NOTICE: Stresses above those listed under “Absolute Maximums Rating” may cause permanent damage to the device. These are stress rating only; functional operation beyond the “Operation Conditions” is not recommended and extended exposure beyond the “Operation Conditions” may affect device reliability. RECOMMENDED OPERATING CONDITIONS Symbol Parameter +VCC Power Supply Voltage Vcm Input Common Mode Range Typical Units 3.3 to 5.0 V VCC to VEE + 1.25V V ELECTRICAL PERFORMANCE CHARACTERISTICS (TC = -55°C TO +125°C, +VCC = +5.0V -- UNLESS OTHERWISE SPECIFIED) Parameter Symbol Input Offset Voltage (Differential) 1/ VOS Input Offset Current IOS Input Bias Current 1/ 1/ IB Conditions Min Max Units -6 6 mV TC = +25°C, +125°C -100 100 pA TC = +25°C -100 100 TC = +125°C -1000 1000 pA Input Common Mode Rejection Ratio CMRR 60 dB Power Supply Rejection Ratio (Differential) PSRR 70 dB 4.9 V Output Voltage High VOH ROUT = 3.6KΩ to GND Output Voltage Low VOL ROUT = 3.6KΩ to VCC Short Circuit Output Current 2/ Slew Rate 1/ Open Loop Gain 1/ SCD5903 Rev B Preliminary 3/4/14 0.1 V IO(SINK) VOUT to VCC -100 180 mA IO(SOURCE) VOUT to VEE 120 200 mA SR RL = 8K, Gain = 1 2.0 V/uS AOL No Load 90 dB 3 Aeroflex Plainview ELECTRICAL PERFORMANCE CHARACTERISTICS (continued) (TC = -55°C TO +125°C, +VCC = +5.0V -- UNLESS OTHERWISE SPECIFIED) Parameter Symbol Unity Gain Bandwidth 1/ UGBW Input Voltage - Enable (EN_AB, EN_CD) Input Current - Enable (EN_AB, EN_CD) Quiescent Supply Current Conditions Min Max RL = 10K 5.8 MHz VHI High (Enabled) 3.5 V VLO Low (Disabled) IEN 1/ Units All Amplifiers Enabled, No Load ICCQ All Amplifier Disabled RL = 2K, f = 1.0KHz Channel Separation 2/ Input-Referred Voltage Noise 2/ en 21 Typical @ F = 5 kHz Phase Margin 2/ m TC = +25°C, No Load 1.5 V 10 nA 5 mA 200 uA dB 84 nV/ Hz Deg 30 Notes: 1/ Specification derated to reflect Total Dose exposure to 1 Mrad(Si) @ +25°C. 2/ Not tested. Shall be guaranteed by design, characterization, or correlation to other test parameters. SWITCHING CHARACTERISTICS (TC = -55°C TO +125°C, +VCC = +5.0V -- UNLESS OTHERWISE SPECIFIED) Symbol Parameter Conditions Min Max Units Output Delay (Enabled) tONEN 500 ns Output Delay (Disabled) tOFFEN 100 ns VCC ENABLES (EN_AB or EN_CD) 50% GND tONEN VOUT (VOUT_A&B or VOUT_C&D) VCC HI Z HI Z GND tOFFEN FIGURE 3: RHD5903 SWITCHING DIAGRAM SCD5903 Rev B Preliminary 3/4/14 4 Aeroflex Plainview Note: Package and lid are electrically isolated from signal pads. FIGURE 4: PACKAGE OUTLINE SCD5903 Rev B Preliminary 3/4/14 5 Aeroflex Plainview ORDERING INFORMATION Model DLA SMD # Screening RHD5903-7 - Commercial Flow, +25°C testing only RHD5903 - Military Temperature, -55°C to +125°C Screened in accordance with the individual Test Methods of MIL-STD-883 RHD5903-201-1S 5962-1223701KXC RHD5903-201-2S 5962-1223701KXA RHD5903-901-1S 5962H1223701KXC RHD5903-901-2S 5962H1223701KXA Package 20-pin SOIC Package DLA SMD Pending DLA Radiation Certification Pending EXPORT CONTROL: This product is controlled for export under the International Traffic in Arms Regulations (ITAR). A license from the U.S. Government is required prior to the export of this product from the United States. www.aeroflex.com/HiRel [email protected] Datasheet Definitions: Advanced Preliminary Datasheet Product in Development Shipping Non-Flight Prototypes Shipping QML and Reduced HiRel Aeroflex Plainview, Inc. reserves the right to make changes to any products and services described herein at any time without notice. Consult Aeroflex or an authorized sales representative to verify that the information in this data sheet is current before using this product. Aeroflex does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by Aeroflex; nor does the purchase, lease, or use of a product or service from Aeroflex convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual rights of Aeroflex or of third parties. SCD5903 Rev B Preliminary 3/4/14 6 Our passion for performance is defined by three attributes. Solution-Minded Performance-Driven Customer-Focused