PDF Data Sheet Rev. 0

FEATURES
FUNCTIONAL BLOCK DIAGRAM
AVDD1 AVDD2 AVDD3 AVDD1_SR DVDD DRVDD
SPIVDD
(1.25V) (2.5V) (3.3V)
(1.25V) (1.25V) (1.25V) (1.8V TO 3.3V)
BUFFER
Rev. 0
DDC
FD
4
SERDOUT0±
SERDOUT1±
SERDOUT2±
SERDOUT3±
CONTROL
REGISTERS
V_1P0
FAST
DETECT
÷2
÷4
÷8
AGND
SYSREF±
SPI CONTROL
AD9690
DRGND DGND SDIO SCLK CSB
PDWN/
STBY
12834-001
CLK+
CLK–
SYNCINB±
JESD204B
SUBCLASS 1
CONTROL
CLOCK
GENERATION
Figure 1.
PRODUCT HIGHLIGHTS
1.
2.
3.
APPLICATIONS
Communications
Multiband, multimode digital receivers
3G/4G, TD-SCDMA, W-CDMA, GSM, LTE
General-purpose software radios
Ultrawideband satellite receivers
Instrumentation
Radars
Signals intelligence (SIGINT)
DOCSIS 3.0 CMTS upstream receive paths
HFC digital reverse path receivers
Wideband digital predistortion
ADC 14
CORE
VIN+
VIN–
FAST
DETECT
JESD204B (Subclass 1) coded serial digital outputs
2.0 W total power at 1 GSPS (default settings)
1.5 W total power at 500 MSPS (default settings)
SFDR = 85 dBFS at 340 MHz, 80 dBFS at 985 MHz
SNR = 65.3 dBFS at 340 MHz (AIN = −1.0 dBFS),
60.5 dBFS at 985 MHz
ENOB = 10.8 bits at 10 MHz
DNL = ±0.5 LSB
INL = ±2.5 LSB
Noise density = −154 dBFS/Hz at 1 GSPS
1.25 V, 2.5 V, and 3.3 V dc supply operation
No missing codes
Internal ADC voltage reference
Flexible input range
AD9690-1000: 1.46 V p-p to 1.94 V p-p (1.70 V p-p nominal)
AD9690-500: 1.46 V p-p to 2.06 V p-p (2.06 V p-p nominal)
Programmable termination impedance
400 Ω, 200 Ω, 100 Ω, and 50 Ω differential
2 GHz usable analog input full power bandwidth
Amplitude detect bits for efficient AGC implementation
2 integrated wideband digital processors
12-bit NCO, up to 4 cascaded half-band filters
Differential clock input
Integer clock divide by 1, 2, 4, or 8
Flexible JESD204B lane configurations
Small signal dither
JESD204B
HIGH SPEED SERIALIZER +
Tx OUTPUTS
Data Sheet
14-Bit, 1 GSPS/500 MSPS JESD204B,
Analog-to-Digital Converter
AD9690
4.
5.
6.
Wide full power bandwidth supports IF sampling of signals
up to 2 GHz.
Buffered inputs with programmable input termination eases
filter design and implementation.
Two integrated wideband decimation filters and numerically
controlled oscillator (NCO) blocks supporting multiband
receivers.
Flexible serial port interface (SPI) controls various product
features and functions to meet specific system requirements.
Programmable fast overrange detection.
9 mm × 9 mm, 64-lead LFCSP.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
©2015 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD9690
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
DDC NCO Plus Mixer Loss and SFDR ................................... 41
Applications ....................................................................................... 1
Numerically Controlled Oscillator .......................................... 41
Functional Block Diagram .............................................................. 1
FIR Filters ........................................................................................ 43
Product Highlights ........................................................................... 1
General Description ................................................................... 43
Revision History ............................................................................... 2
Half-Band Filters ........................................................................ 44
General Description ......................................................................... 3
DDC Gain Stage ......................................................................... 46
Specifications..................................................................................... 4
DDC Complex—Real Conversion ........................................... 46
DC Specifications ......................................................................... 4
DDC Example Configurations ................................................. 47
AC Specifications.......................................................................... 5
Digital Outputs ............................................................................... 48
Digital Specifications ................................................................... 6
Introduction to the JESD204B Interface ................................. 48
Switching Specifications .............................................................. 7
JESD204B Overview .................................................................. 48
Timing Specifications .................................................................. 8
Functional Overview ................................................................. 49
Absolute Maximum Ratings .......................................................... 10
JESD204B Link Establishment ................................................. 49
Thermal Characteristics ............................................................ 10
Physical Layer (Driver) Outputs .............................................. 51
ESD Caution ................................................................................ 10
JESD204B Tx Converter Mapping ........................................... 53
Pin Configuration and Function Descriptions ........................... 11
Configuring the JESD204B Link .............................................. 54
Typical Performance Characteristics ........................................... 13
Multichip Synchronization............................................................ 56
AD9690-1000 .............................................................................. 13
SYSREF± Setup/Hold Window Monitor ................................. 58
AD9690-500 ................................................................................ 17
Test Modes ....................................................................................... 60
Equivalent Circuits ......................................................................... 21
ADC Test Modes ........................................................................ 60
Theory of Operation ...................................................................... 23
JESD204B Block Test Modes .................................................... 61
ADC Architecture ...................................................................... 23
Serial Port Interface ........................................................................ 63
Analog Input Considerations.................................................... 23
Configuration Using the SPI ..................................................... 63
Voltage Reference ....................................................................... 27
Hardware Interface ..................................................................... 63
Clock Input Considerations ...................................................... 28
SPI Accessible Features .............................................................. 63
ADC Overrange and Fast Detect .................................................. 30
Memory Map .................................................................................. 64
ADC Overrange .......................................................................... 30
Reading the Memory Map Register Table............................... 64
Fast Threshold Detection (FD)................................................. 30
Memory Map Register Table ..................................................... 65
Signal Monitor ................................................................................ 31
Applications Information .............................................................. 76
SPORT Over JESD204B ............................................................. 31
Power Supply Recommendations............................................. 76
Digital Downconverter (DDC) ..................................................... 34
Exposed Pad Thermal Heat Slug Recommendations ............ 76
DDC I/Q Input Selection .......................................................... 34
AVDD1_SR (Pin 57) and AGND (Pin 56 and Pin 60) .............. 76
DDC I/Q Output Selection ....................................................... 34
Outline Dimensions ....................................................................... 77
DDC General Description ........................................................ 34
Ordering Guide .......................................................................... 77
Frequency Translation ................................................................... 40
General Description ................................................................... 40
REVISION HISTORY
1/15—Revision 0: Initial Version
Rev. 0 | Page 2 of 77
Data Sheet
AD9690
GENERAL DESCRIPTION
The AD9690 is a 14-bit, 1 GSPS/500 MSPS analog-to-digital
converter (ADC). The device has an on-chip buffer and sampleand-hold circuit designed for low power, small size, and ease of
use. This device is designed for sampling wide bandwidth
analog signals of up to 2 GHz. The AD9690 is optimized for
wide input bandwidth, high sampling rate, excellent linearity,
and low power in a small package.
function in the communications receiver. The programmable
threshold detector allows monitoring of the incoming signal
power using the fast detect output bits of the ADC. If the input
signal level exceeds the programmable threshold, the fast detect
indicator goes high. Because this threshold indicator has low
latency, the user can quickly turn down the system gain to avoid
an overrange condition at the ADC input.
The ADC core features a multistage, differential pipelined
architecture with integrated output error correction logic. The
ADC features wide bandwidth inputs supporting a variety of
user-selectable input ranges. An integrated voltage reference
eases design considerations.
Users can configure the Subclass 1 JESD204B-based high speed
serialized output in a variety of one-, two-, or four-lane configurations, depending on the DDC configuration and the
acceptable lane rate of the receiving logic device. Multiple device
synchronization is supported through the SYSREF± and
SYNCINB± input pins.
The analog input and clock signals are differential inputs. The
ADC data output is internally connected to two digital downconverters (DDCs). Each DDC consists of four cascaded signal
processing stages: a 12-bit frequency translator (NCO), and four
half-band decimation filters.
In addition to the DDC blocks, the AD9690 has several
functions that simplify the automatic gain control (AGC)
The AD9690 has flexible power-down options that allow
significant power savings when desired. All of these features can
be programmed using a 1.8 V to 3.3 V capable 3-wire SPI.
The AD9690 is available in a Pb-free, 64-lead LFCSP and is
specified over the −40°C to +85°C industrial temperature range.
This product is protected by a U.S. patent.
Rev. 0 | Page 3 of 77
AD9690
Data Sheet
SPECIFICATIONS
DC SPECIFICATIONS
AVDD1 = 1.25 V, AVDD2 = 2.5 V, AVDD3 = 3.3 V, AVDD1_SR = 1.25 V, DVDD = 1.25 V, DRVDD = 1.25 V, SPIVDD = 1.8 V, specified
maximum sampling rate for each speed grade, AIN = −1.0 dBFS, clock divider = 2, default SPI settings, TA = 25°C, unless otherwise noted.
Table 1.
Parameter
RESOLUTION
ACCURACY
No Missing Codes
Offset Error
Gain Error
Differential Nonlinearity (DNL)
Integral Nonlinearity (INL)
TEMPERATURE DRIFT
Offset Error
Gain Error
INTERNAL VOLTAGE REFERENCE
Voltage
INPUT-REFERRED NOISE
VREF = 1.0 V
ANALOG INPUTS
Differential Input Voltage Range (Programmable)
Common-Mode Voltage (VCM)
Differential Input Capacitance
Analog Input Full Power Bandwidth
POWER SUPPLY
AVDD1
AVDD2
AVDD3
AVDD1_SR
DVDD
DRVDD
SPIVDD
IAVDD1
IAVDD2
IAVDD3
IAVDD1_SR
IDVDD1
IDRVDD1
ISPIVDD
POWER CONSUMPTION
Total Power Dissipation (Including Output Drivers)1
Power-Down Dissipation
Standby2
Temperature
Full
Min
14
Full
Full
Full
Full
Full
−0.3
−6
−0.6
−4.5
AD9690-500
Typ
Max
Guaranteed
0
+0.3
0
+6
±0.5
+0.7
±2.5
+5.0
Min
14
−0.31
−6
−0.7
−5.7
AD9690-1000
Typ
Max
Guaranteed
0
+0.31
0
+6
±0.5
+0.8
±2.5
+6.9
Unit
Bits
% FSR
% FSR
LSB
LSB
25°C
25°C
−9
±25
−14
±13.8
ppm/°C
ppm/°C
Full
1.0
1.0
V
25°C
2.06
2.63
LSB rms
Full
25°C
25°C
25°C
1.46
2.06
2.05
1.5
2
2.06
1.46
1.70
2.05
1.5
2
1.94
V p-p
V
pF
GHz
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
1.22
2.44
3.2
1.22
1.22
1.22
1.7
1.25
2.5
3.3
1.25
1.25
1.25
1.8
245
279
61
16
73
109
5
1.28
2.56
3.4
1.28
1.28
1.28
3.4
286
343
75
18
107
181
6
1.22
2.44
3.2
1.22
1.22
1.22
1.7
1.25
2.5
3.3
1.25
1.25
1.25
1.8
370
370
83
15
129
147
5
1.28
2.56
3.4
1.28
1.28
1.28
3.4
409
456
100
18
159
175
6
V
V
V
V
V
V
V
mA
mA
mA
mA
mA
mA
mA
Full
Full
Full
1.5
600
900
2.0
700
1100
W
mW
mW
Default mode. No DDCs used. 500 MSPS is L = 2, M = 1, and F = 1; 1000 MSPS is L = 4, M = 1, and F = 1. Power dissipation on DRVDD changes with lane rate and
number of lanes used. Care must be taken to ensure that the serial line rate for a given configuration is within the supported range of 3.125 Gbps to 12.5 Gbps.
2
Can be controlled by the SPI.
1
Rev. 0 | Page 4 of 77
Data Sheet
AD9690
AC SPECIFICATIONS
AVDD1 = 1.25 V, AVDD2 = 2.5 V, AVDD3 = 3.3 V, AVDD1_SR = 1.25 V, DVDD = 1.25 V, DRVDD = 1.25 V, SPIVDD = 1.8 V, specified
maximum sampling rate for each speed grade, AIN = −1.0 dBFS, clock divider = 2, default SPI settings, TA = 25°C, unless otherwise noted.
Table 2.
Parameter1
ANALOG INPUT FULL SCALE
NOISE DENSITY2
SIGNAL-TO-NOISE RATIO (SNR)3
fIN = 10 MHz
fIN = 170 MHz
fIN = 340 MHz
fIN = 450 MHz
fIN = 765 MHz
fIN = 985 MHz
fIN = 1950 MHz
SNR AND DISTORTION RATIO (SINAD)3
fIN = 10 MHz
fIN = 170 MHz
fIN = 340 MHz
fIN = 450 MHz
fIN = 765 MHz
fIN = 985 MHz
fIN = 1950 MHz
EFFECTIVE NUMBER OF BITS (ENOB)
fIN = 10 MHz
fIN = 170 MHz
fIN = 340 MHz
fIN = 450 MHz
fIN = 765 MHz
fIN = 985 MHz
fIN = 1950 MHz
SPURIOUS-FREE DYNAMIC RANGE (SFDR)3
fIN = 10 MHz
fIN = 170 MHz
fIN = 340 MHz
fIN = 450 MHz
fIN = 765 MHz
fIN = 985 MHz
fIN = 1950 MHz
WORST HARMONIC, SECOND OR THIRD3
fIN = 10 MHz
fIN = 170 MHz
fIN = 340 MHz
fIN = 450 MHz
fIN = 765 MHz
fIN = 985 MHz
fIN = 1950 MHz
Temperature
Full
Full
25°C
Full
25°C
25°C
25°C
25°C
25°C
25°C
Full
25°C
25°C
25°C
25°C
25°C
25°C
Full
25°C
25°C
25°C
25°C
25°C
25°C
Full
25°C
25°C
25°C
25°C
25°C
25°C
Full
25°C
25°C
25°C
25°C
25°C
Rev. 0 | Page 5 of 77
AD9690-500
Min Typ
Max
2.06
−153
67.8
66.6
10.8
80
69.2
69.0
68.6
68.0
64.4
63.8
60.5
65.1
69.0
68.8
68.4
67.9
64.2
63.6
60.3
65.0
11.2
11.1
11.1
11.0
10.4
10.3
9.7
10.5
83
88
83
81
80
75
70
−83
−88
−83
−81
−80
−75
−70
AD9690-1000
Min Typ
Max
1.7
−154
75
−75
Unit
V p-p
dBFS/Hz
67.2
66.6
65.3
64.0
61.5
60.5
57.0
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
67.1
66.4
65.2
63.8
62.1
61.1
56.0
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
10.8
10.7
10.5
10.3
10.0
9.8
9.0
Bits
Bits
Bits
Bits
Bits
Bits
Bits
88
85
85
82
82
80
68
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
−88
−85
−85
−82
−82
−80
−68
−75
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
AD9690
Parameter1
WORST OTHER, EXCLUDING SECOND OR THIRD HARMONIC3
fIN = 10 MHz
fIN = 170 MHz
fIN = 340 MHz
fIN = 450 MHz
fIN = 765 MHz
fIN = 985 MHz
fIN = 1950 MHz
TWO-TONE INTERMODULATION DISTORTION (IMD),
AIN1 AND AIN2 = −7 dBFS
fIN1 = 185 MHz, fIN2 = 188 MHz
fIN1 = 338 MHz, fIN2 = 341 MHz
FULL POWER BANDWIDTH4
Data Sheet
Temperature
AD9690-500
Min Typ
Max
25°C
Full
25°C
25°C
25°C
25°C
25°C
−95
−95
−93
−93
−88
−89
−84
25°C
25°C
25°C
−88
−88
2
AD9690-1000
Min Typ
Max
−82
−95
−94
−88
−86
−81
−82
−75
Unit
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
dBFS
−81
−87
−88
2
dBFS
dBFS
GHz
See the AN-835 Application Note, Understanding High Speed ADC Testing and Evaluation, for definitions and for details on how these tests were completed.
Noise density is measured at a low analog input frequency (30 MHz).
See Table 10 for the recommended settings for full-scale voltage and buffer current.
4
Measured with the circuit shown in Figure 64.
1
2
3
DIGITAL SPECIFICATIONS
AVDD1 = 1.25 V, AVDD2 = 2.5 V, AVDD3 = 3.3 V, AVDD1_SR = 1.25 V, DVDD = 1.25 V, DRVDD = 1.25 V, SPIVDD = 1.8 V, specified
maximum sampling rate for each speed grade, AIN = −1.0 dBFS, clock divider = 2, default SPI settings, TA = 25°C, unless otherwise noted.
Table 3.
Parameter
CLOCK INPUTS (CLK+, CLK−)
Logic Compliance
Differential Input Voltage
Input Common-Mode Voltage
Input Resistance (Differential)
Input Capacitance
SYSREF INPUTS (SYSREF+, SYSREF−)
Logic Compliance
Differential Input Voltage
Input Common-Mode Voltage
Input Resistance (Differential)
Input Capacitance (Differential)
LOGIC INPUTS (SDI, SCLK, CSB, PDWN/STBY)
Logic Compliance
Logic 1 Voltage
Logic 0 Voltage
Input Resistance
LOGIC OUTPUT (SDIO)
Logic Compliance
Logic 1 Voltage (IOH = 800 µA)
Logic 0 Voltage (IOL = 50 µA)
SYNCIN INPUT (SYNCINB+/SYNCINB−)
Logic Compliance
Differential Input Voltage
Input Common-Mode Voltage
Input Resistance (Differential)
Input Capacitance
Temperature
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Full
Min
600
Rev. 0 | Page 6 of 77
LVDS/LVPECL
1200
0.85
35
Max
Unit
1800
mV p-p
V
kΩ
pF
2.5
400
0.6
LVDS/LVPECL
1200
0.85
35
1800
2.0
2.5
0
Full
Full
Full
Full
Full
Full
Full
Full
Typ
400
0.6
mV p-p
V
kΩ
pF
CMOS
0.8 × SPIVDD
0.2 × SPIVDD
30
V
V
kΩ
CMOS
0.8 × SPIVDD
0.2 × SPIVDD
V
V
LVDS/LVPECL/CMOS
1200
1800
0.85
2.0
35
2.5
mV p-p
V
kΩ
pF
Data Sheet
AD9690
Parameter
LOGIC OUTPUT (FD)
Logic Compliance
Logic 1 Voltage
Logic 0 Voltage
Input Resistance
DIGITAL OUTPUTS (SERDOUTx±, x = 0 TO 3)
Logic Compliance
Differential Output Voltage
Output Common-Mode Voltage (VCM)
AC Coupled
Short-Circuit Current (IDSHORT)
Differential Return Loss (RLDIFF)1
Common-Mode Return Loss (RLCM)1
Differential Termination Impedance
1
Temperature
Min
Typ
Max
Full
Full
Full
Full
0.8
0
CMOS
SPIVDD
0
30
Unit
V
V
kΩ
Full
Full
360
CML
770
mV p-p
25°C
25°C
25°C
25°C
Full
0
−100
8
6
80
1.8
+100
V
mA
dB
dB
Ω
100
120
Differential and common-mode return loss is measured from 100 MHz to 0.75 MHz × baud rate.
SWITCHING SPECIFICATIONS
AVDD1 = 1.25 V, AVDD2 = 2.5 V, AVDD3 = 3.3 V, AVDD1_SR = 1.25 V, DVDD = 1.25 V, DRVDD = 1.25 V, SPIVDD = 1.8 V, specified
maximum sampling rate for each speed grade, AIN = −1.0 dBFS, default SPI settings, TA = 25°C, unless otherwise noted.
Table 4.
Parameter
CLOCK
Clock Rate (at CLK+/CLK− Pins)
Maximum Sample Rate1
Minimum Sample Rate2
Clock Pulse Width High
Clock Pulse Width Low
OUTPUT PARAMETERS
Unit Interval (UI)3
Rise Time (tR) (20% to 80% into 100 Ω Load)
Fall Time (tF) (20% to 80% into 100 Ω Load)
PLL Lock Time
Data Rate (NRZ)4
LATENCY5
Pipeline Latency
Fast Detect Latency
Wake-Up Time6
Standby
Power-Down
APERTURE
Aperture Delay (tA)
Aperture Uncertainty (Jitter, tj)
Out-of-range Recovery Time
AD9690-500
Typ
Max
Temperature
Min
Full
Full
Full
Full
Full
0.3
500
300
1000
1000
Full
25°C
25°C
25°C
25°C
80
24
24
3.125
4
200
32
32
2
5
Full
Full
55
25°C
25°C
1
Full
Full
Full
530
55
1
AD9690-1000
Min
Typ
Max
Unit
0.3
1000
300
500
500
GHz
MSPS
MSPS
ps
ps
80
24
24
12.5
3.125
4
100
32
32
2
10
The maximum sample rate is the clock rate after the divider.
The minimum sample rate operates at 300 MSPS with L = 2 or L = 1.
Baud rate = 1/UI. A subset of this range can be supported.
4
Default L = 4. This number can be changed based on the sample rate and decimation ratio.
5
No DDCs used. L = 2, M = 1, F = 1.
6
Wake-up time is defined as the time required to return to normal operation from power-down mode.
3
Rev. 0 | Page 7 of 77
Clock cycles
Clock cycles
4
ms
ms
1
4
2
28
55
28
1
12.5
ps
ps
ps
ms
Gbps
530
55
1
ps
fs rms
Clock Cycles
AD9690
Data Sheet
TIMING SPECIFICATIONS
Table 5.
Parameter
CLK+ to SYSREF+ TIMING REQUIREMENTS
tSU_SR
tH_SR
SPI TIMING REQUIREMENTS
tDS
tDH
tCLK
tS
tH
tHIGH
tLOW
tEN_SDIO
Test Conditions/Comments
See Figure 3
Device clock to SYSREF+ setup time
Device clock to SYSREF+ hold time
See Figure 4
Setup time between the data and the rising edge of SCLK
Hold time between the data and the rising edge of SCLK
Period of the SCLK
Setup time between CSB and SCLK
Hold time between CSB and SCLK
Minimum period that SCLK must be in a logic high state
Minimum period that SCLK must be in a logic low state
Time required for the SDIO pin to switch from an input to an
output relative to the SCLK falling edge (not shown in Figure 4)
Time required for the SDIO pin to switch from an output to an
input relative to the SCLK rising edge (not shown in Figure 4)
tDIS_SDIO
Min
Typ
117
−96
Max
Unit
ps
ps
2
2
40
2
2
10
10
10
ns
ns
ns
ns
ns
ns
ns
ns
10
ns
Timing Diagrams
APERTURE
DELAY
ANALOG
INPUT
SIGNAL
SAMPLE N
N – 54
N+1
N – 55
N – 53
N – 52
N–1
N – 51
CLK–
CLK+
CLK–
CLK+
SERDOUT0–
A
B
C
D
E
F
G
H
I
J
A
B
C
D
E
F
G
H
I
J
A
B
C
D
E
F
G
H
I
J
CONVERTER0 MSB
A
B
C
D
E
F
G
H
I
J
A
B
C
D
E
F
G
H
I
J
A
B
C
D
E
F
G
H
I
J
CONVERTER0 LSB
SERDOUT0+
SERDOUT1–
SAMPLE N – 55
ENCODED INTO 1
8-BIT/10-BIT SYMBOL
SAMPLE N – 54
ENCODED INTO 1
8-BIT/10-BIT SYMBOL
12834-002
SERDOUT1+
SAMPLE N – 53
ENCODED INTO 1
8-BIT/10-BIT SYMBOL
Figure 2. Data Output Timing (Full Bandwidth Mode; L = 2; M = 1; F = 1)
CLK–
CLK+
tSU_SR
tH_SR
12834-003
SYSREF–
SYSREF+
Figure 3. SYSREF± Setup and Hold Timing
Rev. 0 | Page 8 of 77
Data Sheet
AD9690
tHIGH
tDS
tS
tACCESS
tCLK
tDH
tH
tLOW
CSB
SDIO DON’T CARE
DON’T CARE
R/W
A14
A13
A12
A11
A10
A9
A8
A7
D5
Figure 4. Serial Port Interface Timing Diagram
Rev. 0 | Page 9 of 77
D4
D3
D2
D1
D0
DON’T CARE
12834-004
SCLK DON’T CARE
AD9690
Data Sheet
ABSOLUTE MAXIMUM RATINGS
THERMAL CHARACTERISTICS
Table 6.
Parameter
Electrical
AVDD1 to AGND
AVDD1_SR to AGND
AVDD2 to AGND
AVDD3 to AGND
DVDD to DGND
DRVDD to DRGND
SPIVDD to AGND
AGND to DRGND
VIN± to AGND
SCLK, SDIO, CSB to AGND
PDWN/STBY to AGND
Environmental
Operating Temperature Range
Junction Temperature Range
Storage Temperature Range
(Ambient)
Rating
1.32 V
1.32 V
2.75 V
3.63 V
1.32 V
1.32 V
3.63 V
−0.3 V to +0.3 V
3.2 V
−0.3 V to SPIVDD + 0.3 V
−0.3 V to SPIVDD + 0.3 V
−40°C to +85°C
−40°C to +115°C
−65°C to +150°C
Typical θJA, θJB, and θJC are specified vs. the number of printed
circuit board (PCB) layers in different airflow velocities (in m/sec).
Airflow increases heat dissipation effectively reducing θJA and
θJB. In addition, metal in direct contact with the package leads
and exposed pad from metal traces, through holes, ground, and
power planes, reduces θJA. Thermal performance for actual
applications requires careful inspection of the conditions in
an application. The use of appropriate thermal management
techniques is recommended to ensure that the maximum
junction temperature does not exceed the limits shown in Table 6.
Table 7. Thermal Resistance Values
PCB
Type
JEDEC
2s2p
Board
Airflow
Velocity
(m/sec)
0.0
1.0
2.5
ΨJB
6.31, 3
5.91, 3
5.71, 3
θJC_TOP
4.71, 4
N/A5
N/A5
θJC_BOT
1.21, 4
Per JEDEC 51-7, plus JEDEC 51-5 2s2p test board.
Per JEDEC JESD51-2 (still air) or JEDEC JESD51-6 (moving air).
3
Per JEDEC JESD51-8 (still air).
4
Per MIL-STD 883, Method 1012.1.
5
N/A means not applicable.
1
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
θJA
17.81, 2
15.61, 2
15.01, 2
2
ESD CAUTION
Rev. 0 | Page 10 of 77
Unit
°C/W
°C/W
°C/W
Data Sheet
AD9690
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
AVDD1
AVDD2
AVDD2
AVDD1
AGND
SYSREF–
SYSREF+
AVDD1_SR
AGND
AVDD1
CLK–
CLK+
AVDD1
AVDD2
AVDD2
AVDD1
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
AD9690
TOP VIEW
(Not to Scale)
AVDD1
AVDD1
AVDD2
AVDD3
DNC
DNC
AVDD3
AVDD2
AVDD2
AVDD2
SPIVDD
CSB
SCLK
SDIO
DVDD
DGND
NOTES
1. EXPOSED PAD. THE EXPOSED THERMAL PAD ON THE BOTTOM OF THE
PACKAGE PROVIDES THE GROUND REFENCE FOR AVDDx. THIS EXPOSED
PAD MUST BE CONNECTED TO GROUND FOR PROPER OPERATION.
2. DNC = DO NOT CONNECT.
12834-005
FD_A
DRGND
DRVDD
SYNCINB–
SYNCINB+
SERDOUT0–
SERDOUT0+
SERDOUT1–
SERDOUT1+
SERDOUT2–
SERDOUT2+
SERDOUT3–
SERDOUT3+
DRVDD
DRGND
DNC
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AVDD1
AVDD1
AVDD2
AVDD3
VIN–A
VIN+A
AVDD3
AVDD2
AVDD2
AVDD2
AVDD2
V_1P0
SPIVDD
PDWN/STBY
DVDD
DGND
Figure 5. Pin Configuration (Top View)
Table 8. Pin Function Descriptions
Pin No.
Power Supplies
0
Mnemonic
Type
Description
EPAD
Ground
1, 2, 47, 48, 49, 52, 55, 61, 64
3, 8, 9, 10, 11, 39, 40, 41,
46, 50, 51, 62, 63
4, 7, 42, 45
13, 38
15, 34
16, 33
18, 31
19, 30
56, 60
57
Analog
5, 6
12
AVDD1
AVDD2
Supply
Supply
Exposed Pad. The exposed thermal pad on the bottom of the
package provides the ground reference for AVDDx. This
exposed pad must be connected to ground for proper
operation.
Analog Power Supply (1.25 V Nominal).
Analog Power Supply (2.5 V Nominal).
AVDD3
SPIVDD
DVDD
DGND
DRGND
DRVDD
AGND1
AVDD1_SR1
Supply
Supply
Supply
Ground
Ground
Supply
Ground
Supply
Analog Power Supply (3.3 V Nominal).
Digital Power Supply for SPI (1.8 V to 3.3 V).
Digital Power Supply (1.25 V Nominal).
Ground Reference for DVDD.
Ground Reference for DRVDD.
Digital Driver Power Supply (1.25 V Nominal).
Ground Reference for SYSREF±.
Analog Power Supply for SYSREF± (1.25 V Nominal).
VIN−, VIN+
V_1P0
Input
Input/DNC
DNC
CLK+, CLK−
DNC
Input
ADC Analog Input Complement/True.
1.0 V Reference Voltage Input/Do Not Connect. This pin is
configurable through the SPI as a no connect or an input. Do
not connect this pin if using the internal reference. Requires a
1.0 V reference voltage input if using an external voltage
reference source.
Do Not Connect.
Clock Input True/Complement.
44, 43
53, 54
Rev. 0 | Page 11 of 77
AD9690
Pin No.
CMOS Outputs
17
32
Digital Inputs
20, 21
58, 59
Data Outputs
22, 23
24, 25
26, 27
28, 29
Device Under Test (DUT)
Controls
14
35
36
37
1
Data Sheet
Mnemonic
Type
Description
FD
DNC
Output
DNC
Fast Detect Output.
Do Not Connect.
SYNCINB−, SYNCINB+
SYSREF+, SYSREF−
Input
Input
Active Low JESD204B LVDS Sync Input True/Complement.
Active High JESD204B LVDS System Reference Input
True/Complement.
SERDOUT0−, SERDOUT0+
SERDOUT1−, SERDOUT1+
SERDOUT2−, SERDOUT2+
SERDOUT3−, SERDOUT3+
Output
Output
Output
Output
Lane 0 Output Data Complement/True.
Lane 1 Output Data Complement/True.
Lane 2 Output Data Complement/True.
Lane 3 Output Data Complement/True.
PDWN/STBY
Input
SDIO
SCLK
CSB
Input/Output
Input
Input
Power-Down Input (Active High). The operation of this pin
depends on the SPI mode and can be configured as powerdown or standby.
SPI Serial Data Input/Output.
SPI Serial Clock.
SPI Chip Select (Active Low).
To ensure proper ADC operation, connect AVDD1_SR and AGND separately from the AVDD1 and EPAD connection. For more information, refer to the Applications
Information section.
Rev. 0 | Page 12 of 77
Data Sheet
AD9690
TYPICAL PERFORMANCE CHARACTERISTICS
AD9690-1000
AVDD1 = 1.25 V, AVDD1_SR = 1.25 V, AVDD2 = 2.5 V, AVDD3 = 3.3 V, DVDD = 1.25 V, DRVDD = 1.25 V, SPIVDD = 1.8 V, 1.7 V p-p
full-scale differential input, AIN = −1.0 dBFS, default SPI settings, clock divider = 2, TA = 25°C, 128k FFT sample, unless otherwise noted.
See Table 10 for recommended settings.
AIN = –1dBFS
SNR = 67.2dBFS
ENOB = 10.8 BITS
SFDR = 88dBFS
BUFFER CONTROL 1 = 1.5×
–10
–30
AMPLITUDE (dBFS)
–50
–70
–90
–50
–70
–90
0
100
200
300
400
500
FREQUENCY (MHz)
–130
12834-006
–130
0
500
AIN = –1dBFS
SNR = 61.5dBFS
ENOB = 10.1 BITS
SFDR = 82dBFS
BUFFER CONTROL 1 = 6.0×
–20
AMPLITUDE (dBFS)
–50
–70
–90
–40
–60
–80
–100
0
100
200
300
400
500
FREQUENCY (MHz)
–120
12834-007
–130
0
300
400
500
Figure 10. Single-Tone FFT with fIN = 765.3 MHz
0
AIN = –1dBFS
SNR = 65.3dBFS
ENOB = 10.5 BITS
SFDR = 85dBFS
BUFFER CONTROL 1 = 3.0×
AIN = –1dBFS
SNR = 60.5dBFS
ENOB = 9.9 BITS
SFDR = 80dBFS
BUFFER CONTROL 1 = 6.0×
–20
AMPLITUDE (dBFS)
–30
200
FREQUENCY (MHz)
Figure 7. Single-Tone FFT with fIN = 170.3 MHz
–10
100
12834-010
AMPLITUDE (dBFS)
400
0
–110
–50
–70
–90
–110
–40
–60
–80
–100
–130
0
100
200
300
400
FREQUENCY (MHz)
500
12834-008
AMPLITUDE (dBFS)
300
Figure 9. Single-Tone FFT with fIN = 450.3 MHz
AIN = –1dBFS
SNR = 66.6dBFS
ENOB = 10.7 BITS
SFDR = 85dBFS
BUFFER CONTROL 1 = 3.0×
–30
200
FREQUENCY (MHz)
Figure 6. Single-Tone FFT with fIN = 10.3 MHz
–10
100
12834-009
–110
–110
Figure 8. Single-Tone FFT with fIN = 340.3 MHz
–120
0
100
200
300
400
FREQUENCY (MHz)
Figure 11. Single-Tone FFT with fIN = 985.3 MHz
Rev. 0 | Page 13 of 77
500
12834-011
AMPLITUDE (dBFS)
–30
AIN = –1dBFS
SNR = 64.0dBFS
ENOB = 10.3 BITS
SFDR = 82dBFS
BUFFER CONTROL 1 = 3.0×
–10
AD9690
Data Sheet
0
90
85
SFDR (dBFS)
–40
SNR/SFDR (dBFS)
AMPLITUDE (dBFS)
AIN = –1dBFS
SNR = 59.8BFS
ENOB = 9.6 BITS
–20 SFDR = 79dBFS
BUFFER CONTROL 1 = 8.0×
–60
–80
80
75
70
SNR (dBFS)
–100
0
100
200
300
400
500
FREQUENCY (MHz)
60
700
12834-012
–120
800
850
900
950
1000
1050
1100
SAMPLE RATE (MHz)
Figure 15. SNR/SFDR vs. Sample Rate (fS), fIN = 170.3 MHz; Buffer Control 1
(0x018) = 3.0×
Figure 12. Single-Tone FFT with fIN = 1293.3 MHz
0
AIN = –1dBFS
SNR = 57.7dBFS
ENOB = 9.2 BITS
–20 SFDR = 70dBFS
BUFFER CONTROL 1 = 8.0×
90
85
80
–40
SNR/SFDR (dBFS)
AMPLITUDE (dBFS)
750
12834-015
65
–60
–80
75
70
65
0
100
200
300
400
500
FREQUENCY (MHz)
12834-013
–120
Figure 13. Single-Tone FFT with fIN = 1725.3 MHz
1.5× SFDR (dBFS)
1.5× SNR (dBFS)
3.0× SFDR (dBFS)
3.0× SNR (dBFS)
50
10.3
63.3
100.3 170.3 225.3 302.3 341.3 403.3 453.3 502.3
ANALOG INPUT FREQUENCY (MHz)
Figure 16. SNR/SFDR vs. Analog Input Frequency (fIN); fIN < 500 MHz;
Buffer Control 1 (0x018) = 1.5× and 3.0×
0
100
AIN = –1dBFS
SNR = 57dBFS
ENOB = 9.1 BITS
–20 SFDR = 68dBFS
BUFFER CONTROL 1 = 8.0×
90
SNR/SFDR (dBFS)
–40
–60
–80
80
70
60
–120
0
100
200
300
400
FREQUENCY (MHz)
500
50
476.8
4.0× SFDR
4.0× SNRFS
6.0× SFDR
6.0× SNRFS
554.4
593.2
670.8
748.4
826.0
903.6
981.2
ANALOG INPUT FREQUENCY (MHz)
Figure 14. Single-Tone FFT with fIN = 1950.3 MHz
Figure 17. SNR/SFDR vs. Analog Input Frequency (fIN);
500 MHz < fIN < 1 GHz;
Buffer Control1 (0x018) = 4.0× and 6.0×
Rev. 0 | Page 14 of 77
12834-017
–100
12834-014
AMPLITUDE (dBFS)
55
12834-016
60
–100
Data Sheet
AD9690
100
0
–20
AMPLITUDE (dBFS)
90
80
SFDR
70
–40
–60
–80
SNR
60
50
978.5
1065.0
1142.4
1220.0
1297.3
1374.8
1452.2
–120
ANALOG INPUT FREQUENCY (MHz)
0
100
200
300
Figure 18. SNR/SFDR vs. fIN; 1 GHz < fIN < 1.5 GHz;
Buffer Control 1 (0x018) = 6.0×
20
SFDR (dBc)
SFDR (dBFS)
IMD3 (dBc)
IMD3 (dBFS)
0
SFDR/IMD3 (dBc AND dBFS)
90
80
SFDR
70
60
1701.6
1889.7
1795.6
ANALOG INPUT FREQUENCY (MHz)
–80
–100
INPUT AMPLITUDE (dBFS)
Figure 19. SNR/SFDR vs. fIN; 1.5 GHz < fIN < 2 GHz;
Buffer Control 1 (0x018) = 7.5×
Figure 22. Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN) with
fIN1 = 184 MHz and fIN2 = 187 MHz
0
20
AIN1 AND AIN2 = –7dBFS
SFDR = 87dBFS
IMD2 = 93dBFS
IMD3 = 87dBFS
BUFFER CONTROL 1 = 3.0×
SFDR (dBc)
SFDR (dBFS)
IMD3 (dBc)
IMD3 (dBFS)
0
SNR/SFDR (dBc AND dBFS)
–20
–60
–140
–90 –84 –78 –72 –66 –60 –54 –48 –42 –36 –30 –24 –18 –12 –6
12834-019
1607.4
–40
–120
SNR
50
1513.3
–20
12834-022
SNR/SFDR (dBFS)
500
Figure 21. Two-Tone FFT; fIN1 = 338 MHz, fIN2 = 341 MHz
100
–40
–60
–80
–20
–40
–60
–80
–100
–100
–120
0
100
200
300
400
FREQUENCY (MHz)
500
–140
–90 –84 –78 –72 –66 –60 –54 –48 –42 –36 –30 –24 –18 –12 –6
INPUT AMPLITUDE (dBFS)
Figure 23. Two-Tone IMD3/SFDR vs. Input Amplitude (AIN) with
fIN1 = 338 MHz and fIN2 = 341 MHz
Figure 20. Two-Tone FFT; fIN1 = 184 MHz, fIN2 = 187 MHz
Rev. 0 | Page 15 of 77
12834-023
–120
12834-020
AMPLITUDE (dBFS)
400
FREQUENCY (MHz)
12834-021
–100
12834-018
SNR/SFDR (dBFS)
AIN1 AND AIN2 = –7dBFS
SFDR = 88dBFS
IMD2 = 93dBFS
IMD3 = 88dBFS
BUFFER CONTROL 1 = 4.5×
AD9690
Data Sheet
0.6
110
100
90
0.4
80
0.2
60
DNL (LSB)
SNR/SFDR (dB)
70
50
40
30
0
–0.2
20
10
0
INPUT AMPLITUDE (dBFS)
–0.6
12834-024
–20
–90 –84 –78 –72 –66 –60 –54 –48 –42 –36 –30 –24 –18 –12 –6
0
2000
4000
6000
8000
10000
12000
14000
16000
OUTPUT CODE
12834-027
–0.4
SFDR (dBFS)
SFDR (dBc)
SNR (dBFS)
SNR (dBc)
0
–10
Figure 27. DNL, fIN = 15 MHz
Figure 24. SNR/SFDR vs. Analog Input Level, fIN = 170.3 MHz
100
25000
2.63 LSB rms
20000
SFDR
NUMBER OF HITS
80
70
SNR
15000
10000
60
5000
0
10
20
30
40
50
60
70
80
90
TEMPERATURE (°C)
0
12834-025
50
–50 –40 –30 –20 –10
N–6 N–5 N–4 N–3 N–2 N–1
N
N+1 N+2 N+3 N+4 N+5 N+6
CODE
Figure 25. SNR/SFDR vs. Temperature, fIN = 170.3 MHz
12834-028
SNR/SFDR (dBFS)
90
Figure 28. Input-Referred Noise Histogram
2.15
3
2.10
POWER DISSIPATION (W)
2
0
–1
L = 2, M = 1, F = 1
L = 4, M = 1, F = 1
2.00
1.95
1.90
1.85
1.80
–2
–3
0
2000
4000
6000
8000
10000
12000
OUTPUT CODE
14000
16000
Figure 26. INL, fIN = 10.3 MHz
1.70
700
750
800
850
900
950
1000
1050
SAMPLE RATE (MHz)
Figure 29. Power Dissipation vs. Sample Rate (fS)
Rev. 0 | Page 16 of 77
1100
12834-029
1.75
12834-026
INL (LSB)
1
2.05
Data Sheet
AD9690
AD9690-500
AVDD1 = 1.25 V, AVDD1_SR = 1.25 V, AVDD2 = 2.5 V, AVDD3 = 3.3 V, DVDD = 1.25 V, DRVDD = 1.25 V, SPIVDD = 1.8 V, 2.06 V p-p
full-scale differential input, AIN = −1.0 dBFS, default SPI settings, clock divider = 2, TA = 25°C, 128k FFT sample, unless otherwise noted.
See Table 10 for recommended settings.
0
0
AIN = −1dBFS
SNR = 68.9dBFS
ENOB = 10.9 BITS
SFDR = 83dBFS
BUFFER CONTROL 1 = 2.0×
–20
–20
–40
–40
AMPLITUDE (dBFS)
–60
–80
–100
–60
–80
–100
–120
0
25
50
75
100
125
150
175
200
225
250
FREQUENCY (MHz)
–140
12834-030
–140
0
150
175
200
225
250
–40
AMPLITUDE (dBFS)
–60
–80
–120
–60
–80
–100
–120
0
25
50
75
100
125
150
175
200
225
250
FREQUENCY (MHz)
–140
12834-031
–140
0
75
100
125
150
175
200
225
250
Figure 34. Single-Tone FFT with fIN = 765.3 MHz
0
AIN = −1dBFS
SNR = 68.5dBFS
ENOB = 10.9 BITS
SFDR = 83dBFS
BUFFER CONTROL 1 = 4.5×
–20
50
FREQUENCY (MHz)
Figure 31. Single-Tone FFT with fIN = 170.3 MHz
0
25
12834-034
AMPLITUDE (dBFS)
125
AIN = −1dBFS
SNR = 64.7dBFS
ENOB = 10.4 BITS
SFDR = 80dBFS
BUFFER CONTROL 1 = 5.0×
–20
–100
AIN = −1dBFS
SNR = 64.0dBFS
ENOB = 10.3 BITS
SFDR = 76dBFS
BUFFER CONTROL 1 = 5.0×
–20
–40
–40
AMPLITUDE (dBFS)
AMPLITUDE (dBFS)
100
0
–40
–60
–80
–100
–120
–60
–80
–100
–120
0
25
50
75
100
125
150
175
200
225
FREQUENCY (MHz)
250
12834-032
–140
75
Figure 33. Single-Tone FFT with fIN = 450.3 MHz
AIN = −1dBFS
SNR = 68.9dBFS
ENOB = 11 BITS
SFDR = 88dBFS
BUFFER CONTROL 1 = 2.0×
–20
50
FREQUENCY (MHz)
Figure 30. Single-Tone FFT with fIN = 10.3 MHz
0
25
12834-033
–120
Figure 32. Single-Tone FFT with fIN = 340.3 MHz
–140
0
25
50
75
100
125
150
175
200
225
FREQUENCY (MHz)
Figure 35. Single-Tone FFT with fIN = 985.3 MHz
Rev. 0 | Page 17 of 77
250
12834-035
AMPLITUDE (dBFS)
AIN = −1dBFS
SNR = 67.8dBFS
ENOB = 10.8 BITS
SFDR = 83dBFS
BUFFER CONTROL 1 = 4.5×
AD9690
Data Sheet
95
0
AIN = −1dBFS
SNR = 63.0dBFS
ENOB = 10.0 BITS
SFDR = 69dBFS
BUFFER CONTROL 1 = 8.0×
90
SNR/SFDR (dBFS)
–80
80
75
–100
70
–120
65
0
25
50
75
100
125
175
150
200
225
250
FREQUENCY (MHz)
SNR
60
300 320 340 360 380 400 420 440 460 480 500 530 550
12834-036
AMPLITUDE (dBFS)
–60
–140
SAMPLE FREQUENCY (MHz)
Figure 39. SNR/SFDR vs. fS, fIN = 170.3 MHz; Buffer Control 1 = 2.0×
Figure 36. Single-Tone FFT with fIN = 1310.3 MHz
100
0
AIN = −1dBFS
SNR = 61.5dBFS
ENOB = 9.8 BITS
SFDR = 69dBFS
BUFFER CONTROL 1 = 8.0×
–20
90
SNR/SFDR (dBFS)
–40
AMPLITUDE (dBFS)
SFDR
85
–40
12834-039
–20
–60
–80
80
70
–100
60
0
25
50
75
100
125
150
175
200
225
250
FREQUENCY (MHz)
50
10.3
12834-037
–140
95.3
150.3
180.3
240.3
301.3
340.7
390.3
450.3
ANALOG INPUT FREQUENCY (MHz)
Figure 40. SNR/SFDR vs. fIN; fIN < 500 MHz;
Buffer Control 1 (0x018) = 2.0× and 4.5×
Figure 37. Single-Tone FFT with fIN = 1710.3 MHz
100
0
AIN = −1dBFS
SNR = 60.8dBFS
ENOB = 9.6 BITS
SFDR = 68dBFS
BUFFER CONTROL 1 = 8.0×
–20
90
SNR/SFDR (dBFS)
–40
–60
–80
–100
80
70
60
50
450.3
–140
0
25
50
75
100
125
150
175
200
FREQUENCY (MHz)
225
250
4.0× SNR
4.0× SFDR
8.0× SNR
8.0× SFDR
480.3
510.3
515.3
610.3
765.3
810.3
985.3
ANALOG INPUT FREQUENCY (MHz)
Figure 41. SNR/SFDR vs. fIN; 500 MHz < fIN < 1 GHz;
Buffer Control 1 (0x018) = 4.0× and 8.0×
Figure 38. Single-Tone FFT with fIN = 1950.3 MHz
Rev. 0 | Page 18 of 77
1010.3
12834-041
–120
12834-038
AMPLITUDE (dBFS)
2.0× SNR
2.0× SFDR
4.5× SNR
4.5× SFDR
12834-040
–120
Data Sheet
80
0
7.0× SNR
7.0× SFDR
8.0× SNR
8.0× SFDR
70
65
60
1950.3
–80
–120
–90 –84 –78 –72 –66 –60 –54 –48 –42 –36 –30 –24 –18 –12
INPUT AMPLITUDE (dBFS)
Figure 42. SNR/SFDR vs. fIN; 1 GHz < fIN < 2 GHz;
Buffer Control 1 (0x018) = 7.0× and 8.0×
0
Figure 45. Two-Tone SFDR/IMD3 vs. Input Amplitude (AIN) with
fIN1 = 184 MHz and fIN2 = 187 MHz
0
AIN1 AND AIN2 = –7dBFS
SFDR = 88dBFS
IMD2 = 94dBFS
IMD3 = 88dBFS
BUFFER CONTROL 1 = 2.0×
SFDR (dBc)
SFDR (dBFS)
IMD3 (dBc)
IMD3 (dBFS)
–20
SFDR/IMD3 (dBc AND dBFS)
–20
–40
–60
–80
–100
–40
–60
–80
50
100
150
200
250
FREQUENCY (MHz)
–120
–90
12834-043
0
–72
–63
–54
–45
–36
100
SNR/SFDR (dBc AND dBFS)
90
–40
–60
–80
–100
80
70
60
50
40
30
20
10
SFDR (dBFS)
SNR (dBFS)
SFDR (dBc)
SNR (dBc)
0
100
150
200
FREQUENCY (MHz)
250
12834-044
–10
50
–9
110
AIN1 AND AIN2 = –7dBFS
SFDR = 88dBFS
IMD2 = 88dBFS
IMD3 = 89dBFS
BUFFER CONTROL 1 = 4.5×
0
–18
Figure 46. Two-Tone IMD3/SFDR vs. Input Amplitude (AIN) with
fIN1 = 338 MHz and fIN2 = 341 MHz
0
–120
–27
AMPLITUDE (dBFS)
Figure 43. Two-Tone FFT; fIN1 = 184 MHz, fIN2 = 187 MHz
–20
–81
12834-046
–100
Figure 44. Two-Tone FFT; fIN1 = 338 MHz, fIN2 = 341 MHz
–20
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
INPUT AMPLITUDE (dBFS)
Figure 47. SNR/SFDR vs. Analog Input Level, fIN = 170.3 MHz
Rev. 0 | Page 19 of 77
12834-047
AMPLITUDE (dBFS)
–60
12834-045
1205.3
1810.3
1410.3
1600.3
ANALOG INPUT FREQUENCY (MHz)
12834-042
50
1010.3
AMPLITUDE (dBFS)
–40
–100
55
–120
SFDR (dBc)
SFDR (dBFS)
IMD3 (dBc)
IMD3 (dBFS)
–20
SFDR/IMD3 (dBc AND dBFS)
75
SNR/SFDR (dBFS)
AD9690
AD9690
Data Sheet
900000
95
2.06 LSB RMS
800000
SFDR
700000
NUMBER OF HITS
SNR/SFDR (dBFS)
90
85
80
75
600000
500000
400000
300000
200000
SNR
70
10
35
60
85
TEMPERATURE (°C)
0
12834-051
–15
12834-048
65
–40
N – 10
N–9
N–8
N–7
N–6
N–5
N–4
N–3
N–2
N–1
N
N+1
N+2
N+3
N+4
N+5
N+6
N+7
N+8
N+9
N + 10
100000
OUTPUT CODE
Figure 48. SNR/SFDR vs. Temperature, fIN = 170.3 MHz
Figure 51. Input-Referred Noise Histogram
3.0
1.55
2.5
L = 1, M = 1, F = 2
L = 2, M = 1, F = 2
1.50
2.0
1.45
POWER (W)
INL (LSB)
1.5
1.0
0.5
0
–0.5
1.40
1.35
1.30
–1.0
0
2000
4000
6000
8000
10000
12000
14000
16000
OUTPUT CODE
1.20
300 320 340 360 380 400 420 440 460 480 500 520 540
12834-049
–2.0
SAMPLE RATE (MHz)
Figure 49. INL, fIN = 10.3 MHz
Figure 52. Power Dissipation vs. fS
0.8
0.6
DNL (LSB)
0.4
0.2
0
–0.2
–0.4
–0.8
0
2000
4000
6000
8000
10000
12000
OUTPUT CODE
14000
16000
12834-050
–0.6
Figure 50. DNL, fIN = 15 MHz
Rev. 0 | Page 20 of 77
12834-052
1.25
–1.5
Data Sheet
AD9690
EQUIVALENT CIRCUITS
AVDD3
AVDD3
AVDD3
3pF 1.5pF
200Ω
EMPHASIS/SWING
CONTROL (SPI)
VCM
BUFFER
200Ω
DRVDD
AVDD3
AVDD3
DATA+
SERDOUTx+
x = 0, 1, 2, 3
VIN–
DRGND
OUTPUT
DRIVER
DATA–
12834-053
AIN
CONTROL
(SPI)
3pF 1.5pF
SERDOUTx–
x = 0, 1, 2, 3
DRGND
Figure 53. Analog Inputs
Figure 56. Digital Outputs
AVDD1
DVDD
25Ω
CLK+
SYNCINB+
1kΩ
DGND
AVDD1
20kΩ
LEVEL
TRANSLATOR
25Ω
CLK–
DRVDD
20kΩ
VCM = 0.85V
12834-054
DVDD
20kΩ
SYNCINB–
VCM = 0.85V
20kΩ
VCM
1kΩ
12834-057
67Ω
28Ω
10pF
200Ω
400Ω
SYNCINB± PIN
CONTROL (SPI)
DGND
Figure 54. Clock Inputs
Figure 57. SYNCINB± Inputs
AVDD1_SR
SYSREF+
1kΩ
SPIVDD
20kΩ
LEVEL
TRANSLATOR
AVDD1_SR
ESD
PROTECTED
VCM = 0.85V
20kΩ
SCLK
SPIVDD
1kΩ
30kΩ
1kΩ
Figure 55. SYSREF± Inputs
ESD
PROTECTED
12834-058
12834-055
SYSREF–
12834-056
67Ω
200Ω
28Ω
VIN+
Figure 58. SCLK Input
Rev. 0 | Page 21 of 77
AD9690
Data Sheet
SPIVDD
ESD
PROTECTED
30kΩ
1kΩ
CSB
30kΩ
1kΩ
PDWN/
STBY
ESD
PROTECTED
12834-059
ESD
PROTECTED
Figure 59. CSB Input
PDWN
CONTROL (SPI)
Figure 62. PDWN/STBY Input
SPIVDD
ESD
PROTECTED
AVDD2
SDO
ESD
PROTECTED
SPIVDD
1kΩ
SDIO
12834-062
ESD
PROTECTED
SPIVDD
SDI
V_1P0
ESD
PROTECTED
12834-060
ESD
PROTECTED
V_1P0 PIN
CONTROL (SPI)
Figure 63. V_1P0 Input/Output
Figure 60. SDIO Input
SPIVDD
ESD
PROTECTED
FD
FD
JESD LMFC
JESD SYNC~
TEMPERATURE DIODE
FD PIN CONTROL (SPI)
12834-061
ESD
PROTECTED
Figure 61. FD Outputs
Rev. 0 | Page 22 of 77
12834-063
30kΩ
Data Sheet
AD9690
THEORY OF OPERATION
The AD9690 has one analog input channel and two JESD204B
output lane pairs. The ADC is designed to sample wide bandwidth
analog signals of up to 2 GHz. The AD9690 is optimized for wide
input bandwidth, high sampling rate, excellent linearity, and
low power in a small package.
The ADC core features a multistage, differential pipelined
architecture with integrated output error correction logic. The
ADC features a wide bandwidth input supporting a variety of
user-selectable input ranges. An integrated voltage reference
eases design considerations.
The AD9690 has several functions that simplify the AGC
function in a communications receiver. The programmable
threshold detector allows monitoring of the incoming signal
power using the fast detect output bit of the ADC. If the input
signal level exceeds the programmable threshold, the fast detect
indicator goes high. Because this threshold indicator has low
latency, the user can quickly turn down the system gain to avoid
an overrange condition at the ADC input.
The Subclass 1 JESD204B-based high speed serialized output data
rate can be configured in one-lane (L = 1), two-lane (L = 2), and
four-lane (L = 4) configurations, depending on the sample rate
and the decimation ratio. Multiple device synchronization is
supported through the SYSREF± and SYNCINB± input pins.
ADC ARCHITECTURE
The architecture of the AD9690 consists of an input buffered
pipelined ADC. The input buffer is designed to provide a
termination impedance to the analog input signal. This
termination impedance can be changed using the SPI to meet
the termination needs of the driver/amplifier. The default
termination value is set to 400 Ω. The equivalent circuit diagram of
the analog input termination is shown in Figure 53. The input
buffer is optimized for high linearity, low noise, and low power.
The input buffer provides a linear high input impedance (for
ease of drive) and reduces kickback from the ADC. The buffer
is optimized for high linearity, low noise, and low power. The
quantized outputs from each stage are combined into a final
14-bit result in the digital correction logic. The pipelined
architecture permits the first stage to operate with a new input
sample; at the same time, the remaining stages operate with the
preceding samples. Sampling occurs on the rising edge of the clock.
ANALOG INPUT CONSIDERATIONS
The analog input to the AD9690 is a differential buffer. The
internal common-mode voltage of the buffer is 2.05 V. The
clock signal alternately switches the input circuit between
sample mode and hold mode. When the input circuit is switched
into sample mode, the signal source must be capable of charging
the sample capacitors and settling within one-half of a clock cycle.
A small resistor, in series with each input, can help reduce the peak
transient current injected from the output stage of the driving
source. In addition, low Q inductors or ferrite beads can be placed
on each leg of the input to reduce high differential capacitance at
the analog inputs and, thus, achieve the maximum bandwidth of
the ADC. Such use of low Q inductors or ferrite beads is required
when driving the converter front end at high IF frequencies.
Either a differential capacitor or two single-ended capacitors
can be placed on the inputs to provide a matching passive network.
This ultimately creates a low-pass filter at the input, which limits
unwanted broadband noise. For more information, refer to the
AN-742 Application Note, the AN-827 Application Note, and
the Analog Dialogue article “Transformer-Coupled Front-End
for Wideband A/D Converters” (Volume 39, April 2005). In
general, the precise values depend on the application.
For best dynamic performance, the source impedances driving
VIN+ and VIN− must be matched such that common-mode
settling errors are symmetrical. These errors are reduced by the
common-mode rejection of the ADC. An internal reference
buffer creates a differential reference that defines the span of the
ADC core.
Maximum SNR performance is achieved by setting the ADC
to the largest span in a differential configuration. In the case
of the AD9690, the available span is programmable through
the SPI port from 1.46 V p-p to 2.06 V p-p differential, with
1.70 V p-p differential being the default for the AD9690-1000
and 2.06 V p-p differential being the default for the AD9690-500.
Differential Input Configurations
There are several ways to drive the AD9690, either actively or
passively. However, optimum performance is achieved by
driving the analog input differentially.
For applications where SNR and SFDR are key parameters,
differential transformer coupling is the recommended input
configuration (see Figure 64 and Table 9) because the noise
performance of most amplifiers is not adequate to achieve the
true performance of the AD9690.
For low to midrange frequencies, a double balun or double
transformer network (see Figure 64 and Table 9) is recommended
for optimum performance of the AD9690. For higher frequencies
in the second or third Nyquist zones, it is better to remove some
of the front-end passive components to ensure wideband operation
(see Figure 64 and Table 9).
Rev. 0 | Page 23 of 77
AD9690
Data Sheet
0.1µF
R1
R3
R2
C1
ADC
C2
R2
R1
0.1µF
0.1µF
R3
C1
12834-064
BALUN
NOTES
1. SEE TABLE 9 FOR COMPONENT VALUES.
Figure 64. Differential Transformer-Coupled Configuration for the AD9690
Table 9. Differential Transformer-Coupled Input Configuration Component Values
Device
AD9690-500
Frequency Range
DC to 250 MHz
250 MHz to 2 GHz
DC to 500 MHz
500 MHz to 2 GHz
AD9690-1000
Transformer
ETC1-1-13
BAL-0006/BAL-0006SMG
ECT1-1-13/BAL-0006SMG
BAL-0006/BAL-0006SMG
Input Common Mode
The analog inputs of the AD9690 are internally biased to the
common mode as shown in Figure 65. The common-mode
buffer has a limited range in that the performance suffers greatly
if the common-mode voltage drops by more than 100 mV.
Therefore, in dc-coupled applications, set the common-mode
voltage to 2.05 V, ±100 mV to ensure proper ADC operation.
The full-scale voltage setting must be at a 1.7 V p-p differential
if running in a dc-coupled application.
Analog Input Buffer Controls and SFDR Optimization
The AD9690 input buffer offers flexible controls for the analog
inputs, such as input termination, buffer current, and input fullscale adjustment. All the available controls are shown in Figure 65.
R1 (Ω)
10
10
25
25
R2 (Ω)
50
50
25
25
R3 (Ω)
10
10
10
0
C1 (pF)
4
4
4
Open
C2 (pF)
2
2
2
Open
Input Buffer Control Registers (0x018, 0x019, 0x01A,
0x935, 0x934, 0x11A)
The input buffer has many registers that set the bias currents and
other settings for operation at different frequencies. These bias
currents and settings can be changed to suit the input frequency
range of operation. Register 0x018 controls the buffer bias current
to help with the kickback from the ADC core. This setting can be
scaled from a low setting of 1.0× to a high setting of 8.5×. The
default setting is 3.0× for the AD9690-1000, and 2.0× for the
AD9690-500. These settings are sufficient for operation in the first
Nyquist zone for the products. When the input buffer current in
Register 0x018 is set, the amount of current required by the
AVDD3 supply changes. This relationship is shown in Figure 66.
For a complete list of buffer current settings, see Table 36.
AVDD3
300
AVDD3
AD9690-500
AD9690-1000
250
VCM
BUFFER
200Ω
67Ω
28Ω
200Ω
400Ω
10pF
200
AVDD3
3pF 1.5pF
IAVDD3 (mA)
200Ω
67Ω
200Ω
28Ω
VIN+
150
100
AVDD3
AVDD3
50
AIN CONTROL
SPI REGISTERS
(0x008, 0x015,
0x016, 0x018,
0x019, 0x01A,
0x11A, 0x934,
0x935)
0
1.5×
2.5×
3.5×
4.5×
5.5×
6.5×
7.5×
8.5×
BUFFER CONTROL 1 SETTING
12834-065
3pF 1.5pF
Figure 65. Analog Input Controls
Using the 0x018, 0x019, 0x01A, 0x11A, 0x934, and 0x935 registers,
the buffer behavior on each channel can be adjusted to optimize the
SFDR over various input frequencies and bandwidths of interest.
12834-066
VIN–
Figure 66. IAVDD3 vs. Buffer Control 1 Setting in Register 0x018
The 0x019, 0x01A, 0x11A, and 0x935 registers offer secondary
bias controls for the input buffer for frequencies >500 MHz.
Register 0x934 can be used to reduce input capacitance to achieve
wider signal bandwidth but may result in slightly lower linearity
and noise performance. These register settings do not impact the
AVDD3 power as much as Register 0x018 does. For frequencies
<500 MHz, it is recommended to use the default settings for
these registers.
Rev. 0 | Page 24 of 77
Data Sheet
AD9690
Table 10 shows the recommended values for the buffer current
control registers for various speed grades.
80
75
Register 0x11A is used when sampling in higher Nyquist zones
(>500 MHz for the AD9690-1000). This setting enables the ADC
sampling network to optimize the sampling and settling times
internal to the ADC for high frequency operation. For frequencies
greater than 500 MHz, it is recommended to operate the ADC core
at a 1.46 V full-scale setting irrespective of the speed grade. This
setting offers better SFDR without any significant penalty in SNR.
SFDR (dBFS)
70
4.5×
5.5×
6.5×
7.5×
8.5×
1607.4
1701.5
1795.6
12834-069
40
1513.4
1889.8
ANALOG INPUT FREQUENCY (MHz)
Figure 69. Buffer Current Sweeps, AD9690-1000 (SFDR vs. IBUFF);
1500 MHz < fIN < 2000 MHz; Front-End Network Shown in Figure 64
85
In certain high frequency applications, the SFDR can be improved
by reducing the full-scale setting, as shown in Table 10.
80
At high frequencies, the performance of the ADC core is limited
by jitter. The SFDR can be improved by backing off of the full
scale level. Figure 70 shows the SFDR and SNR vs. full-scale input
level at different high frequencies for the AD9690-1000.
75
70
65
80
60
1.5×
3.0×
4.5×
160
210
260
310
360
410
460
ANALOG INPUT FREQUENCY (MHz)
Figure 67. Buffer Current Sweeps, AD9690-1000 (SFDR vs. IBUFF);
fIN < 500 MHz; Front-End Network Shown in Figure 64
85
SFDR (dBFS)
75
110
12834-067
60
1.65GHz
1.52GHz
1.76GHz
1.95GHz
1.9GHz
75
70
70
65
65
4.0×
5.0×
6.0×
80
80
60
75
1.52GHz
1.65GHz
1.76GHz
1.9GHz
1.95GHz
SNR (dBc)
SFDR (dBFS)
55
45
90
50
10
60
50
Figure 67, Figure 68, and Figure 69 show the SFDR vs. analog
input frequency for various buffer settings for the AD9690-1000.
The recommended settings shown in Table 10 were used to take
the data while changing the contents of Register 0x018 only.
55
65
60
55
–3
65
–2
INPUT LEVEL (dBFS)
55
–1
12834-070
SFDR (dBFS)
70
60
Figure 70. SNR/SFDR vs. Analog Input Level vs. Input Frequencies, AD9690-1000
55
Figure 71, Figure 72, and Figure 73 show the SFDR vs. analog
input frequency for various buffer settings for the AD9690-500.
The recommended settings shown in Table 10 were used to take
the data while changing the contents of Register 0x018 only.
50
40
503.4
677.6
851.9
1026.2
1200.5
ANALOG INPUT FREQUENCY (MHz)
1374.8
12834-068
45
Figure 68. Buffer Current Sweeps, AD9690-1000 (SFDR vs. IBUFF);
500 MHz < fIN < 1500 MHz; Front-End Network Shown in Figure 64
Rev. 0 | Page 25 of 77
AD9690
Data Sheet
95
100
4.0×
5.0×
6.0×
7.0×
8.0×
90
90
80
SFDR (dBFS)
SFDR (dBFS)
85
80
70
60
75
50
480.3
510.3
515.3
610.3
765.3
810.3
985.3
ANALOG INPUT FREQUENCY (MHz)
30
10.3
12834-071
65
450.3
40
1.0×
1.5×
2.0×
3.0×
4.5×
95.3
150.3
180.3
240.3
301.3
340.7
390.3
450.3
ANALOG INPUT FREQUENCY (MHz)
Figure 71. Buffer Current Sweeps, AD9690-500 (SFDR vs. IBUFF);
450 MHz < fIN < 1000 MHz; Front-End Network Shown in Figure 64
12834-073
70
Figure 73. SFDR vs. fIN; Buffer Control 1 (0x018) = 1.0×, 1.5×, 2.0×, 3.0×, or 4.5×
80
75
SFDR (dBFS)
70
65
60
55
50
40
1010.3
4.0×
5.0×
6.0×
7.0×
8.0×
1205.3
1410.3
1600.3
1810.3
1950.3
ANALOG INPUT FREQUENCY (MHz)
12834-072
45
Figure 72. Buffer Current Sweeps, AD9690-500 (SFDR vs. IBUFF);
1 GHz < fIN < 2GHz; Front-End Network Shown in Figure 64
Table 10. Recommended Register Settings for SFDR Optimization at Different Input Frequencies
Product
AD9690500
AD96901000
1
2
Frequency
DC to
250 MHz
250 MHz to
500 MHz
500 MHz to
1 GHz
1 GHz to
2 GHz
DC to
150 MHz
DC to
500 MHz
500 MHz to
1 GHz
1 GHz to
2 GHz
Buffer
Control 1
(0x018)
0x20
Buffer
Control 2
(0x019)
0x60
Buffer
Control 3
(0x01A)
0x0A
Buffer
Control 4
(0x11A)
0x00
Buffer
Control 5
(0x935)
0x04
Input
Full-Scale
Range
(0x025)
0x0C
Input
Full-Scale
Control
(0x030)
0x04
Input
Termination
(0x016)1
0x0C/0x1C/…
Input
Capacitance
(0x934)
0x1F
0x70
0x60
0x0A
0x00
0x04
0x0C
0x04
0x0C/0x1C/…
0x1F
0x80
0x40
0x08
0x00
0x00
0x08
0x18
0x0C/0x1C/…
0xF0
0x40
0x08
0x00
0x00
0x08
0x18
0x0C/0x1C/…
0x10
0x50
0x09
0x00
0x04
0x0A
0x18
0x0E/0x1E/…
0x1F or
0x002
0x1F or
0x001
0x1F
0x40
0x50
0x09
0x00
0x04
0x0A
0x18
0x0E/0x1E/…
0x1F
0xA0
0x60
0x09
0x20
0x00
0x08
0x18
0x0E/0x1E/…
0xD0
0x70
0x09
0x20
0x00
0x08
0x18
0x0E/0x1E/…
0x1F or
0x001
0x1F or
0x001
The input termination can be changed to accommodate the application with little or no impact to ac performance.
The input capacitance can be set to 1.5 pF to achieve wider input bandwidth but results in slightly lower ac performance.
Rev. 0 | Page 26 of 77
Data Sheet
AD9690
Absolute Maximum Input Swing
The absolute maximum input swing allowed at the inputs of the
AD9690 is 4.3 V p-p differential. Signals operating near or at
this level can cause permanent damage to the ADC.
VOLTAGE REFERENCE
A stable and accurate 1.0 V voltage reference is built into the
AD9690. This internal 1.0 V reference is used to set the fullscale input range of the ADC. The full-scale input range can
be adjusted via the ADC Function Register 0x025. For more
information on adjusting the input swing, see Table 36. Figure 74
shows the block diagram of the internal 1.0 V reference controls.
the reference voltage. For more information on adjusting the
full-scale level of the AD9690, refer to the Memory Map Register
Table section.
The use of an external reference may be necessary, in some
applications, to enhance the gain accuracy of the ADC or
improve thermal drift characteristics. Figure 75 shows the
typical drift characteristics of the internal 1.0 V reference.
1.0010
1.0009
1.0008
V_1P0 VOLTAGE (V)
1.0007
VIN+
VIN–
ADC
CORE
FULL-SCALE
VOLTAGE
ADJUST
1.0003
1.0002
1.0001
1.0000
V_1P0
0.9998
–50
90
Figure 75. Typical V_1P0 Drift
12834-074
V_1P0 PIN
CONTROL SPI
REGISTER
(0x025, 0x02,
AND 0x024)
Figure 74. Internal Reference Configuration and Controls
The SPI Register 0x024 enables the user to either use this internal
1.0 V reference, or to provide an external 1.0 V reference. When
using an external voltage reference, provide a 1.0 V reference.
The full-scale adjustment is made using the SPI, irrespective of
1
NC
2
GND SET 5
3
VIN
The external reference has to be a stable 1.0 V reference. The
ADR130 is a good option for providing the 1.0 V reference.
Figure 76 shows how the ADR130 can be used to provide the
external 1.0 V reference to the AD9690. The grayed out areas
show unused blocks within the AD9690 while using the
ADR130 to provide the external reference.
INTERNAL
V_1P0
GENERATOR
ADR130
0.1µF
25
0
TEMPERATURE (°C)
12834-075
0.9999
INPUT FULL-SCALE
RANGE ADJUST
SPI REGISTER
(0x025, 0x02,
AND 0x024)
INPUT
1.0004
FULL-SCALE
VOLTAGE
ADJUST
NC 6
VOUT 4
V_1P0
0.1µF
FULL-SCALE
CONTROL
Figure 76. External Reference Using ADR130
Rev. 0 | Page 27 of 77
12834-076
INTERNAL
V_1P0
GENERATOR
1.0006
1.0005
AD9690
Data Sheet
CLOCK INPUT CONSIDERATIONS
Input Clock Divider
For optimum performance, drive the AD9690 sample clock
inputs (CLK+ and CLK−) with a differential signal. This signal
is typically ac-coupled to the CLK+ and CLK− pins via a
transformer or clock drivers. These pins are biased internally
and require no additional biasing.
The AD9690 contains an input clock divider with the ability to
divide the Nyquist input clock by 1, 2, 4, and 8. The divider
ratios can be selected using Register 0x10B. This is shown in
Figure 80.
Figure 77 shows a preferred method for clocking the AD9690.
The low jitter clock source is converted from a single-ended
signal to a differential signal using an RF transformer.
0.1µF
1:1Z
CLK+
CLK+
100Ω
CLK–
CLK–
÷2
0.1µF
÷4
÷8
Figure 77. Transformer-Coupled Differential Clock
Another option is to ac couple a differential CML or LVDS
signal to the sample clock input pins, as shown in Figure 78 and
Figure 79.
3.3V
71Ω
10pF
33Ω
33Ω
Z0 = 50Ω
0.1µF
CLK+
Z0 = 50Ω
0.1µF
0.1µF
CLK+
0.1µF
CLK+
100Ω
CLK–
CLOCK INPUT
50Ω1
150Ω
LVDS
DRIVER
50Ω1
Clock Fine Delay Adjust
ADC
CLK–
0.1µF
RESISTORS ARE OPTIONAL.
12834-079
0.1µF
The AD9690 clock divider can be synchronized using the external
SYSREF± input. A valid SYSREF± causes the clock divider to
reset to a programmable state. This synchronization feature
allows multiple devices to have their clock dividers aligned to
guarantee simultaneous input sampling.
The input clock divider inside the AD9690 provides phase delay
in increments of ½ the input clock cycle. Register 0x10C can be
programmed to enable this delay independently for each channel.
Changing this register does not affect the stability of the
JESD204B link.
Figure 78. Differential CML Sample Clock
CLOCK INPUT
Figure 80. Clock Divider Circuit
Input Clock Divider ½ Period Delay Adjust
12834-078
ADC
CLK–
REG 0x10B
12834-080
50Ω
ADC
12834-077
CLOCK
INPUT
The maximum frequency at the CLK± inputs is 4 GHz. This is
the limit of the divider. In applications where the clock input is
a multiple of the sample clock, care must be taken to program
the appropriate divider ratio into the clock divider before applying
the clock signal. This ensures that the current transients during
device startup are controlled.
Figure 79. Differential LVDS Sample Clock
Clock Duty Cycle Considerations
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals. As a result, these ADCs may
be sensitive to clock duty cycle. Commonly, a 5% tolerance is
required on the clock duty cycle to maintain dynamic performance
characteristics. In applications where the clock duty cycle cannot
be guaranteed to be 50%, a higher multiple frequency clock can be
supplied to the device. The AD9690 can be clocked at 2 GHz with
the internal clock divider set to 2. The output of the divider offers
a 50% duty cycle, high slew rate (fast edge) clock signal to the
internal ADC. See the Memory Map section for more details on
using this feature.
The AD9690 sampling edge instant can be adjusted by writing to
Register 0x117 and Register 0x118. Setting Bit 0 of Register 0x117
enables the feature, and Bits[7:0] of Register 0x118 set the value
of the delay. This value can be programmed individually for
each channel. The clock delay can be adjusted from −151.7 ps
to +150 ps in ~1.7 ps increments. The clock delay adjust takes
effect immediately when it is enabled via SPI writes. Enabling
the clock fine delay adjust in Register 0x117 causes a datapath
reset. However, the contents of Register 0x118 can be changed
without affecting the stability of the JESD204B link.
Clock Jitter Considerations
High speed, high resolution ADCs are sensitive to the quality
of the clock input. The degradation in SNR at a given input
frequency (fA) due only to aperture jitter (tJ) can be calculated by
SNR = 20 × log 10 (2 × π × fA × tJ)
In this equation, the rms aperture jitter represents the root
mean square of all jitter sources, including the clock input,
analog input signal, and ADC aperture jitter specifications. IF
undersampling applications are particularly sensitive to jitter
(see Figure 81).
Rev. 0 | Page 28 of 77
Data Sheet
AD9690
In standby mode, the JESD204B link is not disrupted and
transmits zeroes for all converter samples. This can be changed
using Register 0x571, Bit 7 to select /K/ characters.
130
12.5fS
25fS
50fS
100fS
200fS
400fS
800fS
SNR (dB)
100
90
Temperature Diode
The AD9690 contains a diode-based temperature sensor for
measuring the temperature of the die. This diode can output a
voltage and serve as a coarse temperature sensor to monitor the
internal die temperature.
80
70
60
50
30
10
100
1000
10000
ANALOG INPUT FREQUENCY (MHz)
12834-081
40
Figure 81. Ideal SNR vs. Analog Input Frequency and Jitter
Treat the clock input as an analog signal in cases where aperture
jitter may affect the dynamic range of the AD9690. Separate
power supplies for clock drivers from the ADC output driver
supplies to avoid modulating the clock signal with digital noise.
If the clock is generated from another type of source (by gating,
dividing, or other methods), retime the clock by the original clock
at the last step. Refer to the AN-501 Application Note and the
AN-756 Application Note for more in-depth information about
jitter performance as it relates to ADCs.
Power-Down/Standby Mode
The temperature diode voltage can be output to the FD pin
using the SPI. Use Register 0x028, Bit 0 to enable or disable the
diode. Configure the FD pin to output the diode voltage by
programming Register 0x040[2:0]. See Table 36 for more
information.
The voltage response of the temperature diode (SPIVDD =
1.8 V) is shown in Figure 82.
0.90
0.85
The AD9690 has a PDWN/STBY pin which can be used to
configure the device in power-down or standby mode. The
default operation is PDWN. The PDWN/STBY pin is a logic
high pin. When in power-down mode, the JESD204B link is
disrupted. The power-down option can also be set via
Register 0x03F and Register 0x040.
Rev. 0 | Page 29 of 77
0.80
0.75
0.70
0.65
0.60
–55 –45 –35 –25 –15 –5
5
15 25 35 45 55 65 75 85 95 105 115 125
TEMPERATURE (°C)
Figure 82. Temperature Diode Voltage vs. Temperature
12834-082
110
DIODE VOLTAGE (V)
120
AD9690
Data Sheet
ADC OVERRANGE AND FAST DETECT
The operation of the upper threshold and lower threshold
registers, along with the dwell time registers, is shown in
Figure 83.
In receiver applications, it is desirable to have a mechanism to
reliably determine when the converter is about to be clipped.
The standard overrange bit in the JESD204B outputs provides
information on the state of the analog input that is of limited
usefulness. Therefore, it is helpful to have a programmable
threshold below full scale that allows time to reduce the gain
before the clip actually occurs. In addition, because input
signals can have significant slew rates, the latency of this
function is of major concern. Highly pipelined converters can
have significant latency. The AD9690 contains fast detect
circuitry to monitor the threshold and assert the FD pin.
The FD indicator is asserted if the input magnitude exceeds the
value programmed in the fast detect upper threshold registers,
located at Register 0x247 and Register 0x248. The selected
threshold register is compared with the signal magnitude at the
output of the ADC. The fast upper threshold detection has a
latency of 28 clock cycles (maximum). The approximate upper
threshold magnitude is defined by
Upper Threshold Magnitude (dBFS) = 20 log (Threshold
Magnitude/213)
ADC OVERRANGE
The ADC overrange indicator is asserted when an overrange is
detected on the input of the ADC. The overrange indicator can
be embedded within the JESD204B link as a control bit (when
CSB > 0). The latency of this overrange indicator matches the
sample latency.
The FD indicators are not cleared until the signal drops below
the lower threshold for the programmed dwell time. The lower
threshold is programmed in the fast detect lower threshold
registers, located at Register 0x249 and Register 0x24A. The fast
detect lower threshold register is a 13-bit register that is compared
with the signal magnitude at the output of the ADC. This
comparison is subject to the ADC pipeline latency, but is
accurate in terms of converter resolution. The lower threshold
magnitude is defined by
The AD9690 also records any overrange condition in any of the
eight virtual converters. For more information on the virtual
converters, refer to Figure 88. The overrange status of each virtual
converter is registered as a sticky bit in Register 0x563. The
contents of Register 0x563 can be cleared using Register 0x562,
by toggling the bits corresponding to the virtual converter to set
and reset position.
Lower Threshold Magnitude (dBFS) = 20 log (Threshold
Magnitude/213)
For example, to set an upper threshold of −6 dBFS, write 0xFFF
to Register 0x247 and Register 0x248. To set a lower threshold
of −10 dBFS, write 0xA1D to Register 0x249 and Register 0x24A.
FAST THRESHOLD DETECTION (FD)
The FD bit is immediately set whenever the absolute value of
the input signal exceeds the programmable upper threshold
level. The FD bit is only cleared when the absolute value of the
input signal drops below the lower threshold level for greater
than the programmable dwell time. This feature provides
hysteresis and prevents the FD bit from excessively toggling.
The dwell time can be programmed from 1 to 65,535 sample
clock cycles by placing the desired value in the fast detect dwell
time registers, located at Register 0x24B and Register 0x24C.
See the Memory Map section (Register 0x040, and Register 0x245
to Register 0x24C in Table 36) for more details.
UPPER THRESHOLD
DWELL TIME
LOWER THRESHOLD
DWELL TIME
FD
Figure 83. Threshold Settings for FD Signals
Rev. 0 | Page 30 of 77
TIMER COMPLETES BEFORE
SIGNAL RISES ABOVE
LOWER THRESHOLD
12834-083
MIDSCALE
TIMER RESET BY
RISE ABOVE
LOWER
THRESHOLD
Data Sheet
AD9690
SIGNAL MONITOR
The signal monitor block provides additional information about
the signal being digitized by the ADC. The signal monitor
computes the peak magnitude of the digitized signal. This
information can be used to drive an AGC loop to optimize the
range of the ADC in the presence of real-world signals.
The results of the signal monitor block can be obtained either
by reading back the internal values from the SPI port or by
embedding the signal monitoring information into the
JESD204B interface as special control bits. A 24-bit
programmable period controls the duration of the
measurement. Figure 84 shows the simplified block diagram
of the signal monitor block.
FROM
MEMORY
MAP
SIGNAL MONITOR
PERIOD REGISTER
(SMPR)
0x271, 0x272, 0x273
DOWN
COUNTER
When the monitor period timer reaches a count of 1, the 13-bit
peak level value is transferred to the signal monitor holding
register, which can be read through the memory map or output
through the SPORT over the JESD204B interface. The monitor
period timer is reloaded with the value in the SMPR, and the
countdown is restarted. In addition, the magnitude of the first
input sample is updated in the magnitude storage register, and
the comparison and update procedure, as explained previously,
continues.
IS
COUNT = 1?
LOAD
MAGNITUDE
STORAGE
REGISTER
LOAD
LOAD
SIGNAL
MONITOR
HOLDING
REGISTER
SPORT OVER JESD204B
TO SPORT OVER
JESD204B AND
MEMORY MAP
12834-084
CLEAR
FROM
INPUT
COMPARE
A>B
Figure 84. Signal Monitor Block
The peak detector captures the largest signal within the
observation period. The detector only observes the magnitude
of the signal. The resolution of the peak detector is a 13-bit
value, and the observation period is 24 bits and represents
converter output samples. The peak magnitude can be derived
by using the following equation:
Peak Magnitude (dBFS) = 20log(Peak Detector Value/213)
The magnitude of the input port signal is monitored over a
programmable time period, which is determined by the signal
monitor period register (SMPR). The peak detector function is
enabled by setting Bit 1 of Register 0x270 in the signal monitor
control register. The 24-bit SMPR must be programmed before
activating this mode.
After enabling peak detection mode, the value in the SMPR is
loaded into a monitor period timer, which decrements at the
decimated clock rate. The magnitude of the input signal is
compared with the value in the internal magnitude storage
register (not accessible to the user), and the greater of the two
is updated as the current peak level. The initial value of the
magnitude storage register is set to the current ADC input signal
magnitude. This comparison continues until the monitor period
timer reaches a count of 1.
The signal monitor data can also be serialized and sent over the
JESD204B interface as control bits. These control bits must be
deserialized from the samples to reconstruct the statistical data.
The signal control monitor function is enabled by setting Bits[1:0]
of Register 0x279 and Bit 1 of Register 0x27A. Figure 85 shows
two different example configurations for the signal monitor
control bit locations inside the JESD204B samples. A maximum
of three control bits can be inserted into the JESD204B samples;
however, only one control bit is required for the signal monitor.
Control bits are inserted from MSB to LSB. If only one control bit
is to be inserted (CS = 1), only the most significant control bit is
used (see Example Configuration 1 and Example Configuration 2
in Figure 85). To select the SPORT over JESD204B option,
program Register 0x559, Register 0x55A, and Register 0x58F.
See Table 36 for more information on setting these bits.
Figure 86 shows the 25-bit frame data that encapsulates the
peak detector value. The frame data is transmitted MSB first
with five 5-bit subframes. Each subframe contains a start bit
that can be used by a receiver to validate the deserialized data.
Figure 87 shows the SPORT over JESD204B signal monitor data
with a monitor period timer set to 80 samples.
Rev. 0 | Page 31 of 77
AD9690
Data Sheet
16-BIT JESD204B SAMPLE SIZE (N' = 16)
EXAMPLE
CONFIGURATION 1
(N' = 16, N = 15, CS = 1)
1-BIT
CONTROL
BIT
(CS = 1)
15-BIT CONVERTER RESOLUTION (N = 15)
15
S[14]
X
14
S[13]
X
13
S[12]
X
12
S[11]
X
11
10
S[10]
X
9
S[9]
X
8
S[8]
X
7
S[7]
X
6
S[6]
X
5
S[5]
X
S[4]
X
4
S[3]
X
3
S[2]
X
2
S[1]
X
1
0
S[0]
X
CTRL
[BIT 2]
X
SERIALIZED SIGNAL MONITOR
FRAME DATA
16-BIT JESD204B SAMPLE SIZE (N' = 16)
14-BIT CONVERTER RESOLUTION (N = 14)
15
S[13]
X
14
S[12]
X
13
S[11]
X
12
S[10]
X
11
10
S[9]
X
9
S[8]
X
8
S[7]
X
7
S[6]
X
6
S[5]
X
5
S[4]
X
S[3]
X
4
S[2]
X
3
S[1]
X
2
1
0
S[0]
X
CTRL
[BIT 2]
X
TAIL
X
SERIALIZED SIGNAL MONITOR
FRAME DATA
Figure 85. Signal Monitor Control Bit Locations
5-BIT SUB-FRAMES
5-BIT IDLE
SUB-FRAME
(OPTIONAL)
25-BIT
FRAME
IDLE
1
IDLE
1
IDLE
1
IDLE
1
IDLE
1
5-BIT IDENTIFIER START
0
SUB-FRAME
ID[3]
0
ID[2]
0
ID[1]
0
ID[0]
1
5-BIT DATA
MSB
SUB-FRAME
START
0
P[12]
P[11]
P[10]
P[9]
5-BIT DATA
SUB-FRAME
START
0
P[8]
P[7]
P[6]
P5]
5-BIT DATA
SUB-FRAME
START
0
P[4]
P[3]
P[2]
P1]
5-BIT DATA
LSB
SUB-FRAME
START
0
P[0]
0
0
0
P[] = PEAK MAGNITUDE VALUE
12834-086
EXAMPLE
CONFIGURATION 2
(N' = 16, N = 14, CS = 1)
Figure 86. SPORT over JESD204B Signal Monitor Frame Data
Rev. 0 | Page 32 of 77
12834-085
1
CONTROL
1 TAIL
BIT
BIT
(CS = 1)
Data Sheet
AD9690
SMPR = 80 SAMPLES (0x271 = 0x50; 0x272 = 0x00; 0x273 = 0x00)
80 SAMPLE PERIOD
PAYLOAD #3
25-BIT FRAME (N)
IDENT.
DATA
MSB
DATA
DATA
DATA
LSB
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
80 SAMPLE PERIOD
PAYLOAD #3
25-BIT FRAME (N + 1)
IDENT.
DATA
MSB
DATA
DATA
DATA
LSB
IDLE
IDLE
IDLE
IDLE
IDLE
80 SAMPLE PERIOD
IDENT.
DATA
MSB
DATA
DATA
DATA
LSB
IDLE
IDLE
IDLE
IDLE
IDLE
Figure 87. SPORT over JESD204B Signal Monitor Example with Period = 80 Samples
Rev. 0 | Page 33 of 77
12834-087
PAYLOAD #3
25-BIT FRAME (N + 2)
AD9690
Data Sheet
DIGITAL DOWNCONVERTER (DDC)
The AD9690 includes two digital downconverters (DDC 0 and
DDC 1) that provide filtering and reduce the output data rate.
This digital processing section includes an NCO, a half-band
decimating filter, an FIR filter, a gain stage, and a complex-real
conversion stage. Each of these processing blocks has control lines
that allow it to be independently enabled and disabled to provide
the desired processing function. The digital downconverter can
be configured to output either real data or complex output data.
DDC GENERAL DESCRIPTION
DDC I/Q INPUT SELECTION
The frequency translation stage consists of a 12-bit complex
NCO and quadrature mixers that can be used for frequency
translation of both real or complex input signals. This stage
shifts a portion of the available digital spectrum down to
baseband.
The two DDC blocks are used to extract a portion of the full
digital spectrum captured by the ADC(s). They are intended for
IF sampling or oversampled baseband radios requiring wide
bandwidth input signals.
Each DDC block contains the following signal processing stages:
Frequency Translation Stage (Optional)
The AD9690 has one ADC channel and two DDC channels.
Each DDC channel has two input ports that can be paired to
support real inputs through the I/Q crossbar mux.
The inputs to each DDC are controlled by the DDC input
selection registers (Register 0x311, and Register 0x331). See
Table 36 for information on how to configure the DDCs.
Filtering Stage
After shifting down to baseband, the filtering stage decimates
the frequency spectrum using a chain of up to four half-band
low-pass filters for rate conversion. The decimation process
lowers the output data rate, which in turn reduces the output
interface rate.
DDC I/Q OUTPUT SELECTION
Each DDC channel has two output ports that can be paired to
support both real or complex outputs. For real output signals,
only the DDC Output Port I is used (the DDC Output Port Q is
invalid). For complex I/Q output signals, both DDC Output
Port I and DDC Output Port Q are used.
Gain Stage (Optional)
Due to losses associated with mixing a real input signal down to
baseband, the gain stage compensates by adding an additional 0
dB or 6 dB of gain.
The I/Q outputs to each DDC channel are controlled by the
DDC complex to real enable bit (Bit 3) in the DDC control
registers (Register 0x310, and Register 0x330).
Complex to Real Conversion Stage (Optional)
When real outputs are necessary, the complex to real conversion
stage converts the complex outputs back to real by performing
an fS/4 mixing operation plus a filter to remove the complex
component of the signal.
The Chip Q ignore bit (Bit 5) in the chip application mode
register (Register 0x200) controls the chip output muxing of all
the DDC channels. When all DDC channels use real outputs,
this bit must be set high to ignore all DDC Q output ports.
When any of the DDC channels are set to use complex I/Q
outputs, the user must clear this bit to use both DDC Output
Port I and DDC Output Port Q. For more information, refer to
Figure 96.
Figure 88 shows the detailed block diagram of the DDCs
implemented in the AD9690.
COMPLEX TO REAL
CONVERSION
(OPTIONAL)
COMPLEX TO REAL
CONVERSION
(OPTIONAL)
Q CONVERTER 1
REAL/Q Q
HB1 FIR
DCM = 2
HB2 FIR
DCM = BYPASS OR 2
I
HB3 FIR
DCM = BYPASS OR 2
DDC 1
REAL/I
Q CONVERTER 3
12834-088
SYSREF±
REAL/I
CONVERTER 2
OUTPUT INTERFACE
GAIN = 0dB
OR 6dB
REAL/I
CONVERTER 0
SYSREF±
NCO
+
MIXER
(OPTIONAL)
SYSREF
GAIN = 0dB
OR 6dB
HB1 FIR
DCM = 2
HB2 FIR
DCM = BYPASS OR 2
REAL/Q Q
HB3 FIR
DCM = BYPASS OR 2
NCO
+
MIXER
(OPTIONAL)
HB4 FIR
DCM = BYPASS OR 2
ADC
SAMPLING
AT fS
I/Q CROSSBAR MUX
REAL
I
HB4 FIR
DCM = BYPASS OR 2
DDC 0
REAL/I
SYNCHRONIZATION
CONTROL CIRCUITS
Figure 88. DDC Detailed Block Diagram
Rev. 0 | Page 34 of 77
Data Sheet
AD9690
Figure 89 shows an example usage of one of the two DDC
blocks with a real input signal and four half-band filters (HB4,
HB3, HB2, and HB1). It shows both complex (decimate by 16)
and real (decimate by 8) output options.
the chip decimation ratio sample rate. Whenever the NCO
frequency is set or changed, the DDC soft reset must be issued.
If the DDC soft reset is not issued, the output may potentially
show amplitude variations.
When DDCs have different decimation ratios, the chip
decimation ratio (Register 0x201) must be set to the lowest
decimation ratio of all the DDC blocks. In this scenario,
samples of higher decimation ratio DDCs are repeated to match
Table 11, Table 12, Table 13, Table 14, and Table 15 show the
DDC samples when the chip decimation ratio is set to 1, 2, 4, 8,
or 16, respectively.
Rev. 0 | Page 35 of 77
AD9690
Data Sheet
ADC
ADC
SAMPLING
AT fS
REAL
REAL INPUT—SAMPLED AT fS
BANDWIDTH OF
INTEREST IMAGE
–fS/2
–fS/3
–fS/4
REAL
BANDWIDTH OF
INTEREST
fS/32
–fS/32
DC
–fS/16
fS/16
–fS/8
FREQUENCY TRANSLATION STAGE (OPTIONAL)
DIGITAL MIXER + NCO FOR fS/3 TUNING, THE FREQUENCY
TUNING WORD = ROUND ((fS/3)/fS × 4096) = +1365 (0x555)
fS/8
fS/4
fS/3
fS/2
I
NCO TUNES CENTER OF
BANDWIDTH OF INTEREST
TO BASEBAND
cos(ωt)
REAL
12-BIT
NCO
90°
0°
–sin(ωt)
Q
DIGITAL FILTER
RESPONSE
–fS/2
–fS/3
–fS/4
fS/32
–fS/32
DC
–fS/16
fS/16
–fS/8
BANDWIDTH OF
INTEREST IMAGE
(–6dB LOSS DUE TO
NCO + MIXER)
BANDWIDTH OF INTEREST
(–6dB LOSS DUE TO
NCO + MIXER)
fS/8
fS/4
fS/3
fS/2
FILTERING STAGE
HB4 FIR
4 DIGITAL HALF-BAND FILTERS
(HB4 + HB3 + HB2 + HB1)
I
HALFBAND
FILTER
Q
HALFBAND
FILTER
HB3 FIR
2
HALFBAND
FILTER
2
HALFBAND
FILTER
HB4 FIR
HB2 FIR
2
HALFBAND
FILTER
2
HALFBAND
FILTER
HB3 FIR
HB1 FIR
2
HB2 FIR
HALFBAND
FILTER
I
HB1 FIR
2
HALFBAND
FILTER
Q
6dB GAIN TO
COMPENSATE FOR
NCO + MIXER LOSS
COMPLEX (I/Q) OUTPUTS
GAIN STAGE (OPTIONAL)
DIGITAL FILTER
RESPONSE
I
GAIN STAGE (OPTIONAL)
Q
0dB OR 6dB GAIN
COMPLEX TO REAL
CONVERSION STAGE (OPTIONAL)
fS/4 MIXING + COMPLEX FILTER TO REMOVE Q
–fS/32
fS/32
DC
–fS/16
fS/16
–fS/8
I
REAL (I) OUTPUTS
+6dB
+6dB
fS/8
2
+6dB
2
+6dB
I
Q
–fS/32
fS/32
DC
–fS/16
fS/16
DOWNSAMPLE BY 2
I
DECIMATE BY 8
Q
DECIMATE BY 16
0dB OR 6dB GAIN
Q
COMPLEX REAL/I
TO
REAL
–fS/8
–fS/32
fS/32
DC
–fS/16
fS/16
fS/8
Figure 89. DDC Theory of Operation Example (Real Input—Decimate by 16)
Rev. 0 | Page 36 of 77
12834-089
6dB GAIN TO
COMPENSATE FOR
NCO + MIXER LOSS
Data Sheet
AD9690
Table 11. DDC Samples, Chip Decimation Ratio = 1
HB1 FIR
(DCM1 = 1)
N
N+1
N+2
N+3
N+4
N+5
N+6
N+7
N+8
N+9
N + 10
N + 11
N + 12
N + 13
N + 14
N + 15
N + 16
N + 17
N + 18
N + 19
N + 20
N + 21
N + 22
N + 23
N + 24
N + 25
N + 26
N + 27
N + 28
N + 29
N + 30
N + 31
1
Real (I) Output (Complex to Real Enabled)
HB2 FIR +
HB3 FIR + HB2
HB4 FIR + HB3 FIR +
HB1 FIR
FIR + HB1 FIR
HB2 FIR + HB1 FIR
(DCM1 = 2)
(DCM1 = 4)
(DCM1 = 8)
N
N
N
N+1
N+1
N+1
N
N
N
N+1
N+1
N+1
N+2
N
N
N+3
N+1
N+1
N+2
N
N
N+3
N+1
N+1
N+4
N+2
N
N+5
N+3
N+1
N+4
N+2
N
N+5
N+3
N+1
N+6
N+2
N
N+7
N+3
N+1
N+6
N+2
N
N+7
N+3
N+1
N+8
N+4
N+2
N+9
N+5
N+3
N+8
N+4
N+2
N+9
N+5
N+3
N + 10
N+4
N+2
N + 11
N+5
N+3
N + 10
N+4
N+2
N + 11
N+5
N+3
N + 12
N+6
N+2
N + 13
N+7
N+3
N + 12
N+6
N+2
N + 13
N+7
N+3
N + 14
N+6
N+2
N + 15
N+7
N+3
N + 14
N+6
N+2
N + 15
N+7
N+3
Complex (I/Q) Outputs (Complex to Real Disabled)
HB1 FIR
(DCM1 = 2)
N
N+1
N
N+1
N+2
N+3
N+2
N+3
N+4
N+5
N+4
N+5
N+6
N+7
N+6
N+7
N+8
N+9
N+8
N+9
N + 10
N + 11
N + 10
N + 11
N + 12
N + 13
N + 12
N + 13
N + 14
N + 15
N + 14
N + 15
DCM = decimation.
Rev. 0 | Page 37 of 77
HB2 FIR +
HB1 FIR
(DCM1 = 4)
N
N+1
N
N+1
N
N+1
N
N+1
N+2
N+3
N+2
N+3
N+2
N+3
N+2
N+3
N+4
N+5
N+4
N+5
N+4
N+5
N+4
N+5
N+6
N+7
N+6
N+7
N+6
N+7
N+6
N+7
HB3 FIR + HB2
FIR + HB1 FIR
(DCM1 = 8)
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N+2
N+3
N+2
N+3
N+2
N+3
N+2
N+3
N+2
N+3
N+2
N+3
N+2
N+3
N+2
N+3
HB4 FIR + HB3 FIR +
HB2 FIR + HB1 FIR
(DCM1 = 16)
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
N
N+1
AD9690
Data Sheet
Table 12. DDC Samples, Chip Decimation Ratio = 2
Real (I) Output (Complex to Real Enabled)
HB4 FIR +
HB3 FIR +
HB3 FIR +
HB2 FIR +
HB2 FIR +
HB2 FIR +
HB1 FIR
HB1 FIR
HB1 FIR
(DCM1 = 2)
(DCM1 = 4)
(DCM1 = 8)
N
N
N
N+1
N+1
N+1
N
N
N+2
N+1
N+1
N+3
N
+
2
N
N+4
N
+
3
N+1
N+5
N+2
N
N+6
N+3
N+1
N+7
N+4
N+2
N+8
N+5
N+3
N+9
N+4
N+2
N + 10
N+5
N+3
N + 11
N+6
N+2
N + 12
N+7
N+3
N + 13
N+6
N+2
N + 14
N+7
N+3
N + 15
1
Complex (I/Q) Outputs (Complex to Real Disabled)
HB4 FIR +
HB3 FIR +
HB3 FIR +
HB2 FIR +
HB2 FIR +
HB2 FIR +
HB1 FIR
HB1 FIR
HB1 FIR
HB1 FIR
(DCM1 = 2)
(DCM1 = 4)
(DCM1 = 8)
(DCM1 = 16)
N
N
N
N
N+1
N+1
N+1
N+1
N+2
N
N
N
N+3
N+1
N+1
N+1
N+4
N+2
N
N
N+5
N+3
N+1
N+1
N+6
N+2
N
N
N+7
N+3
N+1
N+1
N+8
N+4
N+2
N
N+9
N+5
N+3
N+1
N + 10
N+4
N+2
N
N + 11
N+5
N+3
N+1
N + 12
N+6
N+2
N
N + 13
N+7
N+3
N+1
N + 14
N+6
N+2
N
N + 15
N+7
N+3
N+1
DCM = decimation.
Table 13. DDC Samples, Chip Decimation Ratio = 4
Real (I) Output (Complex to Real Enabled)
HB4 FIR + HB3 FIR +
HB3 FIR + HB2 FIR +
HB2 FIR + HB1 FIR
HB1 FIR (DCM1 = 4)
(DCM1 = 8)
N
N
N+1
N+1
N
N+2
N+1
N+3
N+2
N+4
N+3
N+5
N+2
N+6
N+3
N+7
1
Complex (I/Q) Outputs (Complex to Real Disabled)
HB4 FIR + HB3 FIR +
HB2 FIR + HB1 FIR
HB3 FIR + HB2 FIR +
HB2 FIR + HB1 FIR
(DCM1 = 4)
HB1 FIR (DCM1 = 8)
(DCM1 = 16)
N
N
N
N+1
N+1
N+1
N+2
N
N
N+3
N+1
N+1
N+4
N+2
N
N+5
N+3
N+1
N+6
N+2
N
N+7
N+3
N+1
DCM = decimation.
Table 14. DDC Samples, Chip Decimation Ratio = 8
Real (I) Output (Complex to Real Enabled)
HB4 FIR + HB3 FIR + HB2 FIR + HB1 FIR (DCM1 = 8)
N
N+1
N+2
N+3
N+4
N+5
N+6
N+7
1
Complex (I/Q) Outputs (Complex to Real Disabled)
HB3 FIR + HB2 FIR + HB1 FIR
HB4 FIR + HB3 FIR + HB2 FIR +
(DCM1 = 8)
HB1 FIR (DCM1 = 16)
N
N
N+1
N+1
N+2
N
N+3
N+1
N+4
N+2
N+5
N+3
N+6
N+2
N+7
N+3
DCM = decimation.
Rev. 0 | Page 38 of 77
Data Sheet
AD9690
Table 15. DDC Samples, Chip Decimation Ratio = 16
Real (I) Output (Complex to Real Enabled)
HB4 FIR + HB3 FIR + HB2 FIR + HB1 FIR (DCM1 = 16)
Not applicable
Not applicable
Not applicable
Not applicable
1
Complex (I/Q) Outputs (Complex to Real Disabled)
HB4 FIR + HB3 FIR + HB2 FIR + HB1 FIR (DCM1 = 16)
N
N+1
N+2
N+3
DCM = decimation.
If the chip decimation ratio is set to decimate by 4, DDC 0 is set to use HB2 + HB1 filters (complex outputs decimate by 4), and DDC 1 is
set to use HB4 + HB3 + HB2 + HB1 filters (real outputs decimate by 8), then DDC 1 repeats its output data two times for every one
DDC 0 output. The resulting output samples are shown in Table 16.
Table 16. DDC Output Samples when Chip DCM1 = 4, DDC 0 DCM1 = 4 (Complex), and DDC 1 DCM1 = 8 (Real)
DDC Input Samples
N
N+1
N+2
N+3
N+4
N+5
N+6
N+7
N+8
N+9
N + 10
N + 11
N + 12
N + 13
N + 14
N + 15
1
Output Port I
I0 [N]
DDC 0
Output Port Q
Q0 [N]
Output Port I
I1 [N]
DDC 1
Output Port Q
Not applicable
I0 [N + 1]
Q0 [N + 1]
I1 [N + 1]
Not applicable
I0 [N + 2]
Q0 [N + 2]
I1 [N]
Not applicable
I0 [N + 3]
Q0 [N + 3]
I1 [N + 1]
Not applicable
DCM = decimation.
Rev. 0 | Page 39 of 77
AD9690
Data Sheet
FREQUENCY TRANSLATION
GENERAL DESCRIPTION
Variable IF Mode
Frequency translation is accomplished by using a 12-bit
complex NCO along with a digital quadrature mixer. The
frequency translation translates either a real or complex input
signal from an intermediate frequency (IF) to a baseband
complex digital output (carrier frequency = 0 Hz).
NCO and mixers are enabled. NCO output frequency can be
used to digitally tune the IF frequency.
0 Hz IF (ZIF) Mode
Mixers are bypassed and the NCO disabled.
fS/4 Hz IF Mode
The frequency translation stage of each DDC can be controlled
individually and supports four different IF modes using Bits[5:4] of
the DDC control registers (Register 0x310, and Register 0x330).
These IF modes are
Test Mode
Input samples are forced to 0.999 to positive full scale. NCO is
enabled. This test mode allows the NCOs to directly drive the
decimation filters.
Variable IF mode
0 Hz IF (ZIF) mode
fS/4 Hz IF mode
Test mode
Figure 90 and Figure 91 show examples of the frequency
translation stage for both real and complex inputs.
NCO FREQUENCY TUNING WORD (FTW) SELECTION
12-BIT NCO FTW = MIXING FREQUENCY/ADC SAMPLE RATE × 4096
I
ADC + DIGITAL MIXER + NCO
REAL INPUT—SAMPLED AT fS
REAL
ADC
SAMPLING
AT fS
cos(ωt)
REAL
12-BIT
NCO
90°
0°
COMPLEX
–sin(ωt)
Q
BANDWIDTH OF
INTEREST
BANDWIDTH OF
INTEREST IMAGE
–fS/2
–fS/3
–fS/4
–fS/8
–fS/32
fS/32
DC
–fS/16
fS/16
fS/8
fS/4
fS/3
fS/2
–6dB LOSS DUE TO
NCO + MIXER
12-BIT NCO FTW =
ROUND ((fS/3)/fS × 4096) = +1365 (0x555)
POSITIVE FTW VALUES
–fS/32
DC
fS/32
12-BIT NCO FTW =
ROUND ((fS/3)/fS × 4096) = –1365 (0xAAB)
–fS/32
NEGATIVE FTW VALUES
DC
fS/32
Figure 90. DDC NCO Frequency Tuning Word Selection—Real Inputs
Rev. 0 | Page 40 of 77
12834-090
•
•
•
•
Mixers and NCO are enabled in special down mixing by fS/4
mode to save power.
Data Sheet
AD9690
NCO FREQUENCY TUNING WORD (FTW) SELECTION
12-BIT NCO FTW = MIXING FREQUENCY/ADC SAMPLE RATE × 4096
QUADRATURE ANALOG MIXER +
2 ADCs + QUADRATURE DIGITAL REAL
MIXER + NCO
COMPLEX INPUT—SAMPLED AT fS
QUADRATURE MIXER
ADC
SAMPLING
AT fS
+
I
I
I
Q
Q
90°
PHASE
12-BIT
NCO
90°
0°
Q
Q
ADC
SAMPLING
AT fS
Q
Q
I
I
–
–sin(ωt)
I
I
+
COMPLEX
Q
+
BANDWIDTH OF
INTEREST
IMAGE DUE TO
ANALOG I/Q
MISMATCH
–fS/3
–fS/4
fS/32
–fS/32
–fS/16
fS/16
DC
–fS/8
fS/8
fS/4
fS/3
fS/2
12-BIT NCO FTW =
ROUND ((fS/3)/fS × 4096) = +1365 (0x555)
POSITIVE FTW VALUES
fS/32
–fS/32
12834-091
–fS/2
DC
Figure 91. DDC NCO Frequency Tuning Word Selection—Complex Inputs
DDC NCO PLUS MIXER LOSS AND SFDR
Setting Up the NCO FTW and POW
When mixing a real input signal down to baseband, 6 dB of loss
is introduced in the signal due to filtering of the negative image.
An additional 0.05 dB of loss is introduced by the NCO. The
total loss of a real input signal mixed down to baseband is 6.05 dB.
For this reason, it is recommended that the user compensate for
this loss by enabling the additional 6 dB of gain in the gain stage
of the DDC to recenter the dynamic range of the signal within
the full scale of the output bits.
The NCO frequency value is given by the 12-bit twos
complement number entered in the NCO FTW. Frequencies
between −fS/2 and fS/2 (fS/2 excluded) are represented using the
following frequency words:
When mixing a complex input signal down to baseband, the
maximum value each I/Q sample can reach is 1.414 × full scale
after it passes through the complex mixer. To avoid overrange
of the I/Q samples and to keep the data bitwidths aligned with
real mixing, 3.06 dB of loss (0.707 × full scale) is introduced in
the mixer for complex signals. An additional 0.05 dB of loss is
introduced by the NCO. The total loss of a complex input signal
mixed down to baseband is −3.11 dB.
The worst case spurious signal from the NCO is greater than
102 dBc SFDR for all output frequencies.
NUMERICALLY CONTROLLED OSCILLATOR
The AD9690 has a 12-bit NCO for each DDC that enables the
frequency translation process. The NCO allows the input
spectrum to be tuned to dc, where it can be effectively filtered
by the subsequent filter blocks to prevent aliasing. The NCO
can be set up by providing a frequency tuning word (FTW) and
a phase offset word (POW).
•
•
•
0x800 represents a frequency of –fS/2.
0x000 represents dc (frequency is 0 Hz).
0x7FF represents a frequency of +fS/2 – fS/212.
The NCO frequency tuning word can be calculated using the
following equation:

Mod( f C , f S ) 

NCO _ FTW = round 212

fS


where:
NCO_FTW is a 12-bit twos complement number representing
the NCO FTW.
fS is the AD9690 sampling frequency (clock rate) in Hz.
fC is the desired carrier frequency in Hz.
Mod( ) is a remainder function. For example, Mod(110,100) =
10, and for negative numbers, Mod(–32, 10) = –2.
round( ) is a rounding function. For example, round(3.6) = 4,
and for negative numbers, round(–3.4)= –3.
Note that this equation applies to the aliasing of signals in the
digital domain (that is, aliasing introduced when digitizing
analog signals).
Rev. 0 | Page 41 of 77
AD9690
Data Sheet
For example, if the ADC sampling frequency (fS) is 1250 MSPS
and the carrier frequency (fC) is 416.667 MHz,
 Mod(416.667,1250 
NCO _ FTW = round 212
 = 1365 MHz
1250


Two methods can be used to synchronize multiple PAWs within
the chip:
•
This, in turn, converts to 0x555 in the 12-bit twos complement
representation for NCO_FTW. The actual carrier frequency can
be calculated based on the following equation:
f C − actual =
•
NCO _ FTW × f S
= 416.56 MHz
212
A 12-bit POW is available for each NCO to create a known phase
relationship between multiple AD9690 chips or individual DDC
channels inside one AD9690.
The following procedure must be followed to update the FTW
and/or POW registers to ensure proper operation of the NCO:
•
•
•
Write to the FTW registers for all the DDCs.
Write to the POW registers for all the DDCs.
Synchronize the NCOs either through the DDC soft reset
bit accessible through the SPI, or through the assertion of
the SYSREF± pin.
Note that the NCOs must be synchronized either through SPI
or through the SYSREF± pin after all writes to the FTW or POW
registers have completed. This synchronization is necessary to
ensure the proper operation of the NCO.
NCO Synchronization
Each NCO contains a separate phase accumulator word (PAW)
that determines the instantaneous phase of the NCO. The initial
reset value of each PAW is determined by the POW described
in the Setting Up the NCO FTW and POW section. The phase
increment value of each PAW is determined by the FTW.
Using the SPI. The DDC NCO soft reset bit in the DDC
synchronization control register (Register 0x300, Bit 4)
can be used to reset all the PAWs in the chip. This is
accomplished by toggling the DDC NCO soft reset bit.
This method can only be used to synchronize DDC
channels within the same AD9690 chip.
Using the SYSREF± pin. When the SYSREF± pin is enabled
in the SYSREF± control registers (Register 0x120 and
Register 0x121), and the DDC synchronization is enabled
in Bits[1:0] in the DDC synchronization control register
(Register 0x300), any subsequent SYSREF± event resets all
the PAWs in the chip. This method can be used to synchronize
DDC channels within the same AD9690 chip, or DDC
channels within separate AD9690 chips.
Mixer
The NCO is accompanied by a mixer, whose operation is
similar to an analog quadrature mixer. The mixer performs the
downconversion of input signals (real or complex) by using the
NCO frequency as a local oscillator. For real input signals, this
mixer performs a real mixer operation (with two multipliers).
For complex input signals, the mixer performs a complex mixer
operation (with four multipliers and two adders). The mixer
adjusts its operation based on the input signal (real or complex)
provided to each individual channel. The selection of real or
complex inputs can be controlled individually for each DDC
block by using Bit 7 of the DDC control register (Register 0x310,
and Register 0x330).
Rev. 0 | Page 42 of 77
Data Sheet
AD9690
FIR FILTERS
GENERAL DESCRIPTION
Table 17 shows the different bandwidth options by including
different half-band filters. In all cases, the DDC filtering stage of
the AD9690 provides less than −0.001 dB of pass-band ripple
and >100 dB of stop-band alias rejection.
There are four sets of decimate-by-2, low-pass, half-band, finite
impulse response (FIR) filters (HB1 FIR, HB2 FIR, HB3 FIR,
and HB4 FIR shown in Figure 88). These filters follow the
frequency translation stage. After the carrier of interest is tuned
down to dc (carrier frequency = 0 Hz), these filters efficiently lower
the sample rate while providing sufficient alias rejection from
unwanted adjacent carriers around the bandwidth of interest.
Table 18 shows the amount of stop-band alias rejection for
multiple pass-band ripple/cutoff points. The decimation ratio of
the filtering stage of each DDC can be controlled individually
through Bits[1:0] of the DDC control registers (0x310, and
0x330).
HB1 FIR is always enabled and cannot be bypassed. The HB2,
HB3, and HB4 FIR filters are optional and can be bypassed for
higher output sample rates.
Table 17. DDC Filter Characteristics
ADC
Sample
Rate
(MSPS)
1000
500
1
Half-Band
Filter
Selection
HB1
Real Output
Output
Sample
Decimation Rate
Ratio
(MSPS)
1
1000
Complex (I/Q) Output
Output
Sample
Decimation Rate
Ratio
(MSPS)
2
500 (I) +
500 (Q)
4
250 (I) +
250 (Q)
8
125 (I) +
125 (Q)
16
62.5 (I) +
62.5 (Q)
HB1 + HB2
2
500
HB1 + HB2
+ HB3
HB1 + HB2
+ HB3 +
HB4
HB1
4
250
8
125
1
500
2
HB1 + HB2
2
250
4
HB1 + HB2
+ HB3
HB1 + HB2
+ HB3 +
HB4
4
125
8
8
62.5
16
250 (I) +
250 (Q)
125 (I) +
125 (Q)
62.5 (I) +
62.5 (Q)
31.25 (I)
+ 31.25
(Q)
Alias
Protected
Bandwidth
(MHz)
385.0
Ideal SNR
Improvement
(dB)1
1
192.5
4
96.3
7
48.1
10
192.5
1
96.3
4
48.1
7
24.1
10
PassBand
Ripple
(dB)
<−0.001
Ideal SNR improvement due to oversampling and filtering = 10log(bandwidth/(fS/2)).
Table 18. DDC Filter Alias Rejection
Alias
Rejection
(dB)
>100
90
85
63.3
25
19.3
10.7
1
Pass-Band Ripple/
Cutoff Point (dB)
<−0.001
<−0.001
<−0.001
<−0.006
−0.5
−1.0
−3.0
Alias Protected Bandwidth for
Real (I) Outputs1
<38.5% × fOUT
<38.7% × fOUT
<38.9% × fOUT
<40% × fOUT
44.4% × fOUT
45.6% × fOUT
48% × fOUT
fOUT is the ADC input sample rate fS/DDC decimation ratio.
Rev. 0 | Page 43 of 77
Alias Protected Bandwidth for
Complex (I/Q) Outputs1
<77% × fOUT
<77.4% × fOUT
<77.8% × fOUT
<80% × fOUT
88.8% × fOUT
91.2% × fOUT
96% × fOUT
Alias
Rejection
(dB)
>100
AD9690
Data Sheet
HALF-BAND FILTERS
Table 20. HB3 Filter Coefficients
The AD9690 offers four half-band filters to enable digital signal
processing of the ADC converted data. The HB1 FIR is always
enabled and cannot be bypassed. The HB2, HB3, and HB4 FIR
filters are optional and can be bypassed for higher output
sample rates.
HB3 Coefficient
Number
C1, C11
C2, C10
C3, C9
C4, C8
C5, C7
C6
Table 19. HB4 Filter Coefficients
HB4 Coefficient
Number
C1, C11
C2, C10
C3, C9
C4, C8
C5, C7
C6
Normalized
Coefficient
0.006042
0
−0.049316
0
0.293273
0.500000
Decimal Coefficient
(15-Bit)
99
0
−808
0
4805
8192
0
0
–20
–40
–60
–80
–100
–120
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
NORMALIZED FREQUENCY (× π RAD/SAMPLE)
Figure 93. HB3 Filter Response
HB2 Filter
The third decimate-by-2, half-band, low-pass FIR filter (HB2)
uses a 19-tap, symmetrical, fixed coefficient filter implementation
that is optimized for low power consumption. The HB2 filter is
only used when complex outputs (decimate by 4, 8, or 16) or
real outputs (decimate by 2, 4, or 8) are enabled; otherwise, the
filter is bypassed.
–20
MAGNITUDE (dB)
Decimal Coefficient
(18-Bit)
859
0
−6661
0
38,570
65,536
12834-093
The first decimate-by-2, half-band, low-pass FIR filter (HB4) uses
an 11-tap, symmetrical, fixed-coefficient filter implementation,
optimized for low power consumption. The HB4 filter is only used
when complex outputs (decimate by 16) or real outputs (decimate
by 8) are enabled; otherwise, the filter is bypassed. Table 19 and
Figure 92 show the coefficients and response of the HB4 filter.
MAGNITUDE (dB)
HB4 Filter
Normalized
Coefficient
0.006554
0
−0.050819
0
0.294266
0.500000
–40
–60
–80
Table 21 and Figure 94 show the coefficients and response of
the HB2 filter.
–100
Table 21. HB2 Filter Coefficients
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
NORMALIZED FREQUENCY (× π RAD/SAMPLE)
12834-092
–120
Figure 92. HB4 Filter Response
HB3 Filter
The second decimate-by-2, half-band, low-pass, FIR filter (HB3)
uses an 11-tap, symmetrical, fixed coefficient filter implementation,
optimized for low power consumption. The HB3 filter is only used
when complex outputs (decimate by 8 or 16) or real outputs
(decimate by 4 or 8) are enabled, otherwise, the filter is bypassed.
Table 20 and Figure 93 show the coefficients and response of
the HB3 filter.
HB2 Coefficient
Number
C1, C19
C2, C18
C3, C17
C4, C16
C5, C15
C6, C14
C7, C13
C8, C12
C9, C11
C10
Rev. 0 | Page 44 of 77
Normalized
Coefficient
0.000614
0
−0.005066
0
0.022179
0
−0.073517
0
0.305786
0.500000
Decimal Coefficient
(19-Bit)
161
0
−1328
0
5814
0
−19,272
0
80,160
131,072
Data Sheet
AD9690
Table 22. HB1 Filter Coefficients
0
MAGNITUDE (dB)
–20
–40
–60
–80
–100
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
NORMALIZED FREQUENCY (× π RAD/SAMPLE)
12834-094
–120
Figure 94. HB2 Filter Response
HB1 Filter
The fourth and final decimate-by-2, half-band, low-pass FIR
filter (HB1) uses a 55-tap, symmetrical, fixed coefficient filter
implementation, optimized for low power consumption. The
HB1 filter is always enabled and cannot be bypassed. Table 22
and Figure 95 show the coefficients and response of the HB1
filter.
0
–40
–60
–80
–100
–120
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
NORMALIZED FREQUENCY (× π RAD/SAMPLE)
12834-095
MAGNITUDE (dB)
–20
HB1 Coefficient
Number
C1, C55
C2, C54
C3, C53
C4, C52
C5, C51
C6, C50
C7, C49
C8, C48
C9, C47
C10, C46
C11, C45
C12, C44
C13, C43
C14, C42
C15, C41
C16, C40
C17, C39
C18, C38
C19, C37
C20, C36
C21, C35
C22, C34
C23, C33
C24, C32
C25, C31
C26, C30
C27, C29
C28
Figure 95. HB1 Filter Response
Rev. 0 | Page 45 of 77
Normalized
Coefficient
−0.000023
0
0.000097
0
−0.000288
0
0.000696
0
−0.0014725
0
0.002827
0
−0.005039
0
0.008491
0
−0.013717
0
0.021591
0
−0.033833
0
0.054806
0
−0.100557
0
0.316421
0.500000
Decimal Coefficient
(21-Bit)
−24
0
102
0
−302
0
730
0
−1544
0
2964
0
−5284
0
8903
0
−14,383
0
22,640
0
−35,476
0
57,468
0
−105,442
0
331,792
524,288
AD9690
Data Sheet
DDC GAIN STAGE
DDC COMPLEX—REAL CONVERSION
Each DDC contains an independently controlled gain stage.
The gain is selectable as either 0 dB or 6 dB. When mixing a real
input signal down to baseband, it is recommended that the user
enable the 6 dB of gain to recenter the dynamic range of the
signal within the full scale of the output bits.
Each DDC contains an independently controlled complex to
real conversion block. The complex to real conversion block
reuses the last filter (HB1 FIR) in the filtering stage, along with
an fS/4 complex mixer to upconvert the signal.
After up converting the signal, the Q portion of the complex
mixer is no longer needed and is dropped.
When mixing a complex input signal down to baseband, the
mixer has already recentered the dynamic range of the signal
within the full scale of the output bits and no additional gain is
necessary. However, the optional 6 dB gain can be used to
compensate for low signal strengths. The downsample by 2
portion of the HB1 FIR filter is bypassed when using the
complex to real conversion stage (see Figure 96).
HB1 FIR
Figure 96 shows a simplified block diagram of the complex to
real conversion.
GAIN STAGE
COMPLEX TO
REAL ENABLE
LOW-PASS
FILTER
I
2
0dB
OR
6dB
I
0 I/REAL
1
COMPLEX TO REAL CONVERSION
0dB
OR
6dB
I
cos(ωt)
+
REAL
90°
fS/4
0°
–
sin(ωt)
LOW-PASS
FILTER
2
Q
0dB
OR
6dB
Q
Q
12834-096
Q
0dB
OR
6dB
HB1 FIR
Figure 96. Complex to Real Conversion Block
Rev. 0 | Page 46 of 77
Data Sheet
AD9690
DDC EXAMPLE CONFIGURATIONS
Table 23 describes the register settings for multiple DDC example configurations.
Table 23. DDC Example Configurations
Chip
Application
Layer
One DDC
Chip
Decimation
Ratio
2
DDC
Input
Type
Real
DDC
Output
Type
Complex
Bandwidth
per DDC1
38.5% × fS
No. of Virtual
Converters
Required
2
Two DDCs
4
Real
Real
9.63% × fS
2
Two DDCs
4
Real
Complex
19.25% × fS
4
Two DDCs
8
Real
Real
4.81% × fS
2
1
2
Register Settings2
Register 0x200 = 0x01 (one DDC; I/Q selected)
Register 0x201 = 0x01 (chip decimate by 2)
Register 0x310 = 0x83 (complex mixer; 0 dB gain; variable IF;
complex outputs; HB1 filter)
Register 0x311 = 0x00 (default)
Register 0x331 = 0x00 (default)
Register 0x314, Register 0x315, Register x0320, Register 0x321 =
FTW and POW set as required by application for DDC 0
Register 0x200 = 0x22 (two DDCs; I only selected)
Register 0x201 = 0x02 (chip decimate by 4)
Register 0x310, Register 0x330 = 0x49 (real mixer; 6 dB gain;
variable IF; real output; HB3 + HB2 + HB1 filters)
Register 0x311 = 0x00 (default)
Register 0x331 = 0x00 (default)
Register 0x314, Register 0x315, Register 0x320, Register 0x321 =
FTW and POW set as required by application for DDC 0
Register 0x334, Register 0x335, Register 0x340, Register 0x341 =
FTW and POW set as required by application for DDC 1
Register 0x200 = 0x02 (two DDCs; I/Q selected)
Register 0x201 = 0x02 (chip decimate by 4)
Register 0x310, Register 0x330 = 0x40 (real mixer; 6 dB gain;
variable IF; complex output; HB2+HB1 filters)
Register 0x311 = 0x00 (default)
Register 0x331 = 0x00 (default)
Register 0x314, Register 0x315, Register 0x320, Register 0x321 =
FTW and POW set as required by application for DDC 0
Register 0x334, Register 0x335, Register 0x340, Register 0x341 =
FTW and POW set as required by application for DDC 1
Register 0x200 = 0x22 (two DDCs; I only selected)
Register 0x201 = 0x03 (chip decimate by 8)
Register 0x310, Register 0x330 = 0x4A (real mixer; 6 dB gain;
variable IF; real output; HB4+HB3+HB2+HB1 filters)
Register 0x311 = 0x00 (default)
Register 0x331 = 0x00 (default)
Register 0x314, Register 0x315, Register 0x320, Register 0x321 =
FTW and POW set as required by application for DDC 0
Register 0x334, Register 0x335, Register 0x340, Register 0x341 =
FTW and POW set as required by application for DDC 1
fS is the ADC sample rate. Bandwidths listed are <−0.001 dB of pass-band ripple and >100 dB of stop-band alias rejection.
The NCOs must be synchronized either through the SPI or through the SYSREF± pin after all writes to the FTW or POW registers have completed, to ensure the proper
operation of the NCO. See the NCO Synchronization section for more information.
Rev. 0 | Page 47 of 77
AD9690
Data Sheet
DIGITAL OUTPUTS
INTRODUCTION TO THE JESD204B INTERFACE
•
The AD9690 digital outputs are designed to the JEDEC
standard JESD204B, serial interface for data converters.
JESD204B is a protocol to link the AD9690 to a digital
processing device over a serial interface with lane rates of up to
12.5 Gbps. The benefits of the JESD204B interface over LVDS
include a reduction in required board area for data interface
routing, and an ability to enable smaller packages for converter
and logic devices.
•
•
•
•
JESD204B OVERVIEW
The JESD204B data transmit block assembles the parallel data
from the ADC into frames and uses 8-bit/10-bit encoding as
well as optional scrambling to form serial output data. Lane
synchronization is supported through the use of special control
characters during the initial establishment of the link. Additional
control characters are embedded in the data stream to maintain
synchronization thereafter. A JESD204B receiver is required to
complete the serial link. For additional details on the JESD204B
interface, refer to the JESD204B standard.
The AD9690 JESD204B data transmit block maps one physical
ADC or up to four virtual converters (when DDCs are enabled)
over a link. A link can be configured to use one, two, or four
JESD204B lanes. The JESD204B specification refers to a number
of parameters to define the link, and these parameters must match
between the JESD204B transmitter (the AD9690 output) and
the JESD204B receiver (the logic device input).
The JESD204B link is described according to the following
parameters:
•
•
•
•
L is the number of lanes/converter device (lanes/link)
(AD9690 value = 1, 2, or 4)
M is the number of converters/converter device (virtual
converters/link) (AD9690 value = 1, 2, or 4)
F is the octets/frame (AD9690 value = 1, 2, 4, 8, or 16)
N΄ is the number of bits per sample (JESD204B word size)
(AD9690 value = 8 or 16)
N is the converter resolution (AD9690 value = 7 to 16)
Figure 97 shows a simplified block diagram of the AD9690
JESD204B link. By default, the AD9690-500 is configured to use
one converter and two lanes, while the AD9690-1000 is
configured to use one converter and four lanes. The AD9690
allows other configurations via a quick configuration register in
the SPI register map, along with additional customizable options.
By default in the AD9690, the 14-bit converter word from each
converter is broken into two octets (eight bits of data). Bit 13
(MSB) through Bit 6 are in the first octet. The second octet
contains Bit 5 through Bit 0 (LSB) and two tail bits. The tail bits
can be configured as zeroes or a pseudorandom number
sequence. The tail bits can also be replaced with control bits
indicating overrange, SYSREF±, or fast detect output.
The two resulting octets can be scrambled. Scrambling is
optional; however, it is recommended to avoid spectral peaks
when transmitting similar digital data patterns. The scrambler
uses a self-synchronizing, polynomial-based algorithm defined
by the equation 1 + x14 + x15. The descrambler in the receiver is
a self-synchronizing version of the scrambler polynomial.
The two octets are then encoded with an 8-bit/10-bit encoder.
The 8-bit/10-bit encoder works by taking eight bits of data (an
octet) and encoding them into a 10-bit symbol. Figure 98 shows
how the 14-bit data is taken from the ADC, how the tail bits are
added, how the two octets are scrambled, and how the octets are
encoded into two 10-bit symbols. Figure 98 illustrates the default
data format when using the C2 control bit.
CONVERTER 0
CONVERTER
INPUT
ADC
MUX/
FORMAT
(SPI
REG 0x561,
REG 0x564)
JESD204B LINK
CONTROL
(L.M.F)
(SPI REG 0x570)
LANE MUX
AND MAPPING
(SPI
REG 0x5B0,
REG 0x5B2,
REG 0x5B3,
REG 0x5B5,
REG 0x5B6)
SERDOUT0–,
SERDOUT0+
SERDOUT1–,
SERDOUT1+
SERDOUT2–,
SERDOUT2+
SERDOUT3–,
SERDOUT3+
12834-097
•
CS is the number of control bits/sample
(AD9690 value = 0, 1, 2, or 3)
K is the number of frames per multiframe
(AD9690 value = 4, 8, 12, 16, 20, 24, 28, or 32 )
S is the samples transmitted/single converter/frame cycle
(AD9690 value = set automatically based on L, M, F, and N΄)
HD is the high density mode (AD9690 = set automatically
based on L, M, F, and N΄)
CF is the number of control words/frame clock
cycle/converter device (AD9690 value = 0)
SYSREF±
SYNCINB±
Figure 97. Transmit Link Simplified Block Diagram Showing Full Bandwidth Mode (Register 0x200 = 0x00)
Rev. 0 | Page 48 of 77
Data Sheet
AD9690
JESD204B
INTERFACE
TEST PATTERN
(REG 0x573,
REG 0x551 TO
REG 0x558)
JESD204B
LONG TRANSPORT
TEST PATTERN
REG 0x571[5]
SERIALIZER
SCRAMBLER
1 + x14 + x15
MSB A13
A12
A11
A10
A9
A8
A6
LSB A7
A5
A4
A3
A2
A1
A0
C2
T
MSB S7
S6
S5
S4
S3
S2
S1
LSB S0
S7
S6
S5
S4
S3
S2
S1
S0
8-BIT/10-BIT
ENCODER
a b
a b c d e f g h i j
SERDOUT0±
SERDOUT1±
i j a b
SYMBOL0
i j
SYMBOL1
a b c d e f g h i j
12834-098
TAIL BITS
0x571[6]
(OPTIONAL)
OCTET 1
JESD204B SAMPLE
CONSTRUCTION
MSB A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
LSB A0
OCTET 1
OCTET 0
FRAME
CONSTRUCTION
OCTET 0
ADC TEST PATTERNS
(RE0x550,
REG 0x551 TO
REG 0x558)
ADC
JESD204B DATA
LINK LAYER TEST
PATTERNS
REG 0x574[2:0]
C2
CONTROL BITS C1
C0
Figure 98. ADC Output Data Path Showing Data Framing
TRANSPORT
LAYER
SAMPLE
CONSTRUCTION
FRAME
CONSTRUCTION
SCRAMBLER
ALIGNMENT
CHARACTER
GENERATION
8-BIT/10-BIT
ENCODER
PHYSICAL
LAYER
CROSSBAR
MUX
SERIALIZER
Tx
OUTPUT
12834-099
PROCESSED
SAMPLES
FROM ADC
DATA LINK
LAYER
SYSREF±
SYNCINB±
Figure 99. Data Flow
FUNCTIONAL OVERVIEW
Physical Layer
The block diagram in Figure 99 shows the flow of data through
the JESD204B hardware from the sample input to the physical
output. The processing can be divided into layers that are
derived from the open source initiative (OSI) model widely
used to describe the abstraction layers of communications
systems. These layers are the transport layer, data link layer,
and physical layer (serializer and output driver).
The physical layer consists of the high speed circuitry clocked at
the serial clock rate. In this layer, parallel data is converted into
one, two, or four lanes of high speed differential serial data.
Transport Layer
The transport layer handles packing the data (consisting of
samples and optional control bits) into JESD204B frames that
are mapped to 8-bit octets. These octets are sent to the data link
layer. The transport layer mapping is controlled by rules derived
from the link parameters. Tail bits are added to fill gaps where
required. The following equation can be used to determine the
number of tail bits within a sample (JESD204B word):
T = N΄ – N – CS
Data Link Layer
The data link layer is responsible for the low level functions
of passing data across the link. These include optionally
scrambling the data, inserting control characters for multichip
synchronization/lane alignment/monitoring, and encoding
8-bit octets into 10-bit symbols. The data link layer is also
responsible for sending the initial lane alignment sequence
(ILAS), which contains the link configuration data used by the
receiver to verify the settings in the transport layer.
JESD204B LINK ESTABLISHMENT
The AD9690 JESD204B transmitter (Tx) interface operates in
Subclass 1 as defined in the JEDEC Standard 204B (July 2011
specification). The link establishment process is divided into the
following steps: code group synchronization and SYNCINB±,
initial lane alignment sequence, and user data and error correction.
Code Group Synchronization (CGS) and SYNCINB±
The CGS is the process by which the JESD204B receiver finds
the boundaries between the 10-bit symbols in the stream of
data. During the CGS phase, the JESD204B transmit block
transmits /K28.5/ characters. The receiver must locate /K28.5/
characters in its input data stream using clock and data recovery
(CDR) techniques.
The receiver issues a synchronization request by asserting the
SYNCINB± pin of the AD9690 low. The JESD204B Tx then begins
sending /K/ characters. Once the receiver has synchronized, it waits
for the correct reception of at least four consecutive /K/ symbols. It
then deasserts SYNCINB±. The AD9690 then transmits an ILAS
on the following local multiframe clock (LMFC) boundary.
For more information on the code group synchronization
phase, refer to the JEDEC Standard JESD204B, July 2011,
Section 5.3.3.1.
The SYNCINB± pin operation can also be controlled by the
SPI. The SYNCINB± signal is a differential dc-coupled LVDS
Rev. 0 | Page 49 of 77
AD9690
Data Sheet
User Data and Error Detection
mode signal by default, but it can also be driven single-ended.
For more information on configuring the SYNCINB± pin
operation, refer to Register 0x572.
The SYNCINB± pins can also be configured to run in CMOS
(single-ended) mode, by setting Bit[4] in Register 0x572. When
running SYNCINB± in CMOS mode, connect the CMOS
SYNCINB signal to Pin 21 (SYNCINB+) and leave Pin 20
(SYNCINB−) floating.
Initial Lane Alignment Sequence (ILAS)
The ILAS phase follows the CGS phase and begins on the next
LMFC boundary. The ILAS consists of four multiframes, with
an /R/ character marking the beginning and an /A/ character
marking the end. The ILAS begins by sending an /R/ character
followed by 0 to 255 ramp data for one multiframe. On the
second multiframe, the link configuration data is sent, starting
with the third character. The second character is a /Q/ character
to confirm that the link configuration data will follow. All
undefined data slots are filled with ramp data. The ILAS
sequence is never scrambled.
The ILAS sequence construction is shown in Figure 100. The
four multiframes include the following:
•
•
•
Multiframe 1. Begins with an /R/ character (/K28.0/) and
ends with an /A/ character (/K28.3/).
Multiframe 2. Begins with an /R/ character followed by a
/Q/ (/K28.4/) character, followed by link configuration
parameters over 14 configuration octets (see Table 24) and
ends with an /A/ character. Many of the parameter values
are of the value – 1 notation.
Multiframe 3. Begins with an /R/ character (/K28.0/) and
ends with an /A/ character (/K28.3/).
Multiframe 4. Begins with an /R/ character (/K28.0/) and
ends with an /A/ character (/K28.3/).
K K R D
D A R Q C
C D
For scrambled data, any 0xFC character at the end of a frame
is replaced by an /F/, and any 0x7C character at the end of a
multiframe is replaced with an /A/. The JESD204B receiver (Rx)
checks for /F/ and /A/ characters in the received data stream
and verifies that they only occur in the expected locations. If an
unexpected /F/ or /A/ character is found, the receiver handles
the situation by using dynamic realignment or asserting the
SYNCINB± signal for more than four frames to initiate a
resynchronization. For unscrambled data, if the final character
of two subsequent frames is equal, the second character is
replaced with an /F/ if it is at the end of a frame, and an /A/ if it
is at the end of a multiframe.
Insertion of alignment characters can be modified using SPI.
The frame alignment character insertion (FACI) is enabled by
default. More information on the link controls is available in the
Memory Map section, Register 0x571.
8-Bit/10-Bit Encoder
The 8-bit/10-bit encoder converts 8-bit octets into 10-bit symbols
and inserts control characters into the stream when needed.
The control characters used in JESD204B are shown in Table 24.
The 8-bit/10-bit encoding ensures that the signal is dc balanced by
using the same number of ones and zeroes across multiple symbols.
The 8-bit/10-bit interface has options that can be controlled via
the SPI. These operations include bypass and invert. These options
are troubleshooting tools for the verification of the digital front
end (DFE). Refer to the Memory Map section, Register 0x572[2:1]
for information on configuring the 8-bit/10-bit encoder.
D A R D
D A R D
D A D
END OF
MULTIFRAME
START OF
ILAS
START OF
USER DATA
START OF LINK
CONFIGURATION DATA
Figure 100. Initial Lane Alignment Sequence
Rev. 0 | Page 50 of 77
12834-100
•
After the initial lane alignment sequence is complete, the user
data is sent. Normally, within a frame, all characters are considered
user data. However, to monitor the frame clock and multiframe
clock synchronization, there is a mechanism for replacing
characters with /F/ or /A/ alignment characters when the data
meets certain conditions. These conditions are different for
unscrambled and scrambled data. The scrambling operation is
enabled by default, but it may be disabled using the SPI.
Data Sheet
AD9690
Table 24. AD9690 Control Characters used in JESD204B
Abbreviation
/R/
/A/
/Q/
/K/
/F/
1
Control Symbol
/K28.0/
/K28.3/
/K28.4/
/K28.5/
/K28.7/
8-Bit Value
000 11100
011 11100
100 11100
101 11100
111 11100
10-Bit Value,
RD1 = −1
001111 0100
001111 0011
001111 0100
001111 1010
001111 1000
10-Bit Value,
RD1 = +1
110000 1011
110000 1100
110000 1101
110000 0101
110000 0111
Description
Start of multiframe
Lane alignment
Start of link configuration data
Group synchronization
Frame alignment
RD = running disparity.
PHYSICAL LAYER (DRIVER) OUTPUTS
Digital Outputs, Timing, and Controls
The AD9690 physical layer consists of drivers that are defined in
the JEDEC Standard JESD204B, July 2011. The differential digital
outputs are powered up by default. The drivers use a dynamic
100 Ω internal termination to reduce unwanted reflections.
Place a 100 Ω differential termination resistor at each receiver
input to result in a nominal 300 mV p-p swing at the receiver
(see Figure 101). Alternatively, single-ended 50 Ω termination
can be used. When single-ended termination is used, the termination voltage is DRVDD/2. Otherwise, 0.1 µF ac coupling
capacitors can be used to terminate to any single-ended voltage.
VRXCM
DRVDD
0.1µF
50Ω
100Ω
DIFFERENTIAL
TRACE PAIR
50Ω
SERDOUTx+
100Ω
OR
RECEIVER
SERDOUTx–
OUTPUT SWING = 300mV p-p
VCM = VRXCM
12834-101
0.1µF
Figure 101. AC-Coupled Digital Output Termination Example
The AD9690 digital outputs can interface with custom ASICs
and FPGA receivers, providing superior switching performance
in noisy environments. Single point-to-point network topologies
are recommended with a single differential 100 Ω termination
resistor placed as close to the receiver inputs as possible. The
common mode of the digital output automatically biases itself
to half the DRVDD supply of 1.2 V (VCM = 0.6 V). See Figure 102
for dc coupling the outputs to the receiver logic.
DRVDD
100Ω
DIFFERENTIAL
TRACE PAIR
If there is no far-end receiver termination, or if there is poor
differential trace routing, timing errors can result. To avoid such
timing errors, it is recommended that the trace length be less
than six inches, and that the differential output traces be close
together and at equal lengths.
Figure 103 to Figure 108 show an example of the digital output
data eye, time interval error (TIE) jitter histogram, and bathtub
curve for one AD9690 lane running at 10 Gbps and 6 Gbps,
respectively. The format of the output data is twos complement
by default. To change the output data format, see the Memory
Map section (Register 0x561 in Table 36).
De-Emphasis
De-emphasis enables the receiver eye diagram mask to be met
in conditions where the interconnect insertion loss does not
meet the JESD204B specification. Use the de-emphasis feature
only when the receiver is unable to recover the clock due to
excessive insertion loss. Under normal conditions, it is disabled
to conserve power. Additionally, enabling and setting too high a
de-emphasis value on a short link can cause the receiver eye
diagram to fail. Use the de-emphasis setting with caution because it
can increase electromagnetic interference (EMI). See the
Memory Map section (Register 0x5C1 to Register 0x5C5 in
Table 36) for more details.
Phase-Locked Loop
The phase-locked loop (PLL) is used to generate the serializer
clock, which operates at the JESD204B lane rate. The status of
the PLL lock can be checked in the PLL locked status bit
(Register 0x56F, Bit 7). This read only bit lets the user know if
the PLL has achieved a lock for the specific setup. The JESD204B
lane rate control, Bit 4 of Register 0x56E, must be set to
correspond with the lane rate.
SERDOUTx+
100Ω
RECEIVER
OUTPUT SWING = 300mV p-p
VCM = DRVDD/2
12834-102
SERDOUTx–
Figure 102. DC-Coupled Digital Output Termination Example
Rev. 0 | Page 51 of 77
AD9690
Data Sheet
400
400
300
300
200
VOLTAGE (mV)
VOLTAGE (mV)
200
100
0
Tx EYE
MASK
–100
100
0
Tx EYE
MASK
–100
–200
–200
–300
–300
–400
–80
–60
–40
–20
0
20
40
60
80
TIME (ps)
–150
–100
–50
0
50
100
150
TIME (ps)
Figure 103. Digital Outputs Data Eye, External 100 Ω Terminations
at 10 Gbps
12834-106
–100
12834-103
–400
Figure 106. Digital Outputs Data Eye, External 100 Ω Terminations
at 6 Gbps
8000
12000
7000
10000
6000
4000
HITS
HITS
8000
6000
4000
3000
4000
2000
2000
–2
0
2
4
6
TIME (ps)
Figure 104. Digital Outputs Histogram, External 100 Ω Terminations
at 10 Gbps
1–2
1–2
1–4
1–4
1–6
1–6
BER
1
1–8
1–10
1–12
1–12
1–14
1–14
–0.3
–0.2
–0.1
0
UI
0.1
0.2
0.3
0.4
0.5
–1
1
0
2
3
4
1–8
1–10
–0.4
–2
Figure 107. Digital Outputs Histogram, External 100 Ω Terminations
at 6 Gbps
1
1–16
–0.5
–3
TIME (ps)
1–16
–0.5
12834-105
BER
0
–4
Figure 105. Digital Outputs Bathtub Curve, External 100 Ω Terminations
at 10 Gbps
–0.4
–0.3
–0.2
–0.1
0
UI
0.1
0.2
0.3
0.4
0.5
12834-108
–4
12834-104
0
12834-107
1000
Figure 108. Digital Outputs Bathtub Curve, External 100 Ω Terminations
at 6 Gbps
Rev. 0 | Page 52 of 77
Data Sheet
AD9690
JESD204B Tx CONVERTER MAPPING
Figure 109 shows a block diagram of the two scenarios
described for I/Q transport layer mapping.
To support the different chip operating modes, the AD9690
design treats each sample stream (real or I/Q) as originating
from separate virtual converters. The I/Q samples are always
mapped in pairs with the I samples mapped to the first virtual
converter and the Q samples mapped to the second virtual
converter. With this transport layer mapping, the number of
virtual converters are the same whether
DIGITAL DOWNCONVERSION
M=2
I
CONVERTER 0
REAL
ADC
REAL
DIGITAL
DOWN
CONVERSION
JESD204B
Tx
L LANES
JESD204B
Tx
L LANES
Q
CONVERTER 1
I/Q ANALOG MIXING
M=2
I
REAL
Σ
ADC
I
CONVERTER 0
90°
PHASE
Q
ADC
Q
CONVERTER 1
Figure 109. I/Q Transport Layer Mapping
REAL/I
REAL/Q
REAL
ADC
SAMPLING
AT fS
I/Q
CROSSBAR
MUX
REAL/I
REAL/Q
DDC 0
I
I
Q
Q
DDC 1
I
I
Q
Q
REAL/I
CONVERTER 0
Q
CONVERTER 1
REAL/I
CONVERTER 2
Q
CONVERTER 3
Figure 110. DDCs and Virtual Converter Mapping
Rev. 0 | Page 53 of 77
OUTPUT
INTERFACE
12834-110
•
A single real converter is used along with a digital
downconverter block producing I/Q outputs, or
An analog downconversion is used with two real
converters producing I/Q outputs.
12834-109
•
The JESD204B Tx block for AD9690 supports up to four DDC
blocks. Each DDC block outputs either two sample streams (I/Q)
for the complex data components (real + imaginary), or one
sample stream for real (I) data. The JESD204B interface can be
configured to use up to four virtual converters depending on the
DDC configuration. Figure 110 shows the virtual converters and
their relationship to the DDC outputs when complex outputs
are used. Table 25 shows the virtual converter mapping for each
chip operating mode when channel swapping is disabled.
AD9690
Data Sheet
Table 25. Virtual Converter Mapping
Number of
Virtual
Converters
Supported
1
1
2
Chip
Operating
Mode
(0x200,
Bits[1:0])
Full
bandwidth
mode (0x0)
One DDC
mode (0x1)
One DDC
mode (0x1)
Two DDC
mode (0x2)
2
4
Two DDC
mode (0x2)
Chip Q
Ignore
(0x200,
Bit 5)
Real (0x0)
Real
(I only)
(0x1)
Complex
(I/Q) (0x0)
Real
(I Only)
(0x1)
Complex
(I/Q) (0x0)
Virtual Converter Mapping
0
ADC
samples
1
Unused
2
Unused
3
Unused
4
Unused
5
Unused
6
Unused
7
Unused
DDC 0 I
samples
Unused
Unused
Unused
Unused
Unused
Unused
Unused
DDC 0 I
samples
DDC 0 I
samples
DDC 0 Q
samples
DDC 1 I
samples
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
DDC 0 I
samples
DDC 0 Q
samples
DDC 1 I
samples
DDC 1 Q
samples
Unused
Unused
Unused
Unused
CONFIGURING THE JESD204B LINK
The AD9690 has one JESD204B link. The device offers an easy
way to set up the JESD204B link through the JESD04B quick
configuration register (Register 0x570). The serial outputs
(SERDOUT0± to SERDOUT3±) are considered to be part of
one JESD204B link. The basic parameters that determine the
link setup are
•
•
•
Number of lanes per link (L)
Number of converters per link (M)
Number of octets per frame (F)
If the internal DDCs are used for on-chip digital processing, M
represents the number of virtual converters. The virtual
converter mapping setup is shown in Figure 110.
The maximum lane rate allowed by the JESD204B specification
is 12.5 Gbps. The lane line rate is related to the JESD204B
parameters using the following equation:
10
M × N '×  × f OUT
 8 
Lane Line Rate =
L
The decimation ratio (DCM) is the parameter programmed in
Register 0x201.
The following steps can be used to configure the output:
1.
2.
3.
4.
5.
6.
If the lane line rate calculated is less than 6.25 Gbps, select the
low line rate option. This is done by programming a value of
0x10 to Register 0x56E.
Table 26 and Table 27 show the JESD204B output
configurations supported for both N΄ = 16 and N΄ = 8 for a
given number of virtual converters. Care must be taken to
ensure that the serial line rate for a given configuration is within
the supported range of 3.125 Gbps to 12.5 Gbps.
where:
f OUT =
Power down the link.
Select quick configuration options.
Configure detailed options
Set output lane mapping (optional).
Set additional driver configuration options (optional).
Power up the link.
f ADC _ CLOCK
Decimation Ratio
Rev. 0 | Page 54 of 77
Data Sheet
AD9690
Table 26. JESD204B Output Configurations for N΄=16
Number of Virtual
Converters
Supported (Same
Value as M)
1
2
4
JESD204B Quick
Configuration
(0x570)
0x01
0x40
0x41
0x80
0x81
0x0A
0x49
0x88
0x89
0x13
0x52
0x91
JESD204B Transport Layer Settings2
JESD204B Serial
Line Rate1
20 × fOUT
10 × fOUT
10 × fOUT
5 × fOUT
5 × fOUT
40 × fOUT
20 × fOUT
10 × fOUT
10 × fOUT
80 × fOUT
40 × fOUT
20 × fOUT
L
1
2
2
4
4
1
2
4
4
1
2
4
M
1
1
1
1
1
2
2
2
2
4
4
4
F
2
1
2
1
2
4
2
1
2
8
4
2
S
1
1
2
2
4
1
1
1
2
1
1
1
HD
0
1
0
1
0
0
0
1
0
0
0
0
N
8 to 16
8 to 16
8 to 16
8 to 16
8 to 16
8 to 16
8 to 16
8 to 16
8 to 16
8 to 16
8 to 16
8 to 16
N΄
16
16
16
16
16
16
16
16
16
16
16
16
CS
0 to 3
0 to 3
0 to 3
0 to 3
0 to 3
0 to 3
0 to 3
0 to 3
0 to 3
0 to 3
0 to 3
0 to 3
K3
Only valid K
values that
are divisible
by 4 are
supported
fOUT = output sample rate = ADC sample rate/chip decimation ratio. The JESD204B serial line rate must be ≥3125 Mbps and ≤12,500 Mbps; when the serial line rate is
≤12.5 Gbps and ≥ 6.25 Gbps, the low line rate mode must be disabled (set Bit 4 to 0x0 in 0x56E). When the serial line rate is <6.25 Gbps and ≥3.125 Gbps, the low line
rate mode must be enabled (set Bit 4 to 0x1 in 0x56E).
2
JESD204B transport layer descriptions are as described in the JESD204B Overview section.
3
For F = 1, K = 20, 24, 28, and 32. For F = 2, K = 12, 16, 20, 24, 28, and 32. For F = 4, K = 8, 12, 16, 20, 24, 28, and 32. For F = 8 and F = 16, K = 4, 8, 12, 16, 20, 24, 28, and 32.
1
Table 27. JESD204B Output Configurations for N΄=8
Number of Virtual
Converters Supported
(Same Value as M)
1
2
JESD204B Quick
Configuration
(0x570)
0x00
0x01
0x40
0x41
0x42
0x80
0x81
0x09
0x48
0x49
0x88
0x89
0x8A
JESD204B Transport Layer Settings2
Serial Line Rate1
10 × fOUT
10 × fOUT
5 × fOUT
5 × fOUT
5 × fOUT
2.5 × fOUT
2.5 × fOUT
20 × fOUT
10 × fOUT
10 × fOUT
5 × fOUT
5 × fOUT
5 × fOUT
L
1
1
2
2
2
4
4
1
2
2
4
4
4
M
1
1
1
1
1
1
1
2
2
2
2
2
2
F
1
2
1
2
4
1
2
2
1
2
1
2
4
S
1
2
2
4
8
4
8
1
1
2
2
4
8
HD
0
0
0
0
0
0
0
0
0
0
0
0
0
N
7 to 8
7 to 8
7 to 8
7 to 8
7 to 8
7 to 8
7 to 8
7 to 8
7 to 8
7 to 8
7 to 8
7 to 8
7 to 8
N΄
8
8
8
8
8
8
8
8
8
8
8
8
8
CS
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
0 to 1
K3
Only valid K
values which
are divisible
by 4 are
supported
fOUT = output sample rate = ADC sample rate/chip decimation ratio. The JESD204B serial line rate must be ≥3125 Mbps and ≤12,500 Mbps; when the serial line rate is
≤12.5 Gbps and ≥6.25 Gbps, the low line rate mode must be disabled (set Bit 4 to 0x0 in Register 0x56E). When the serial line rate is <6.25 Gbps and ≥3.125 Gbps, the
low line rate mode must be enabled (set Bit 4 to 0x1 in Register 0x56E).
2
JESD204B transport layer descriptions are as described in the JESD204B Overview section.
3
For F = 1, K = 20, 24, 28, and 32. For F = 2, K = 12, 16, 20, 24, 28, and 32. For F = 4, K = 8, 12, 16, 20, 24, 28, and 32. For F = 8 and F = 16, K = 4, 8, 12, 16, 20, 24, 28, and 32.
1
Rev. 0 | Page 55 of 77
AD9690
Data Sheet
MULTICHIP SYNCHRONIZATION
The AD9690 has a SYSREF± input that provides flexible options
for synchronizing the internal blocks. The SYSREF± input is a
source synchronous system reference signal that enables multichip
synchronization. The input clock divider, DDCs, signal monitor
block, and JESD204B link can be synchronized using the SYSREF±
input. For the highest level of timing accuracy, SYSREF± must
meet setup and hold requirements relative to the CLK± input.
The flowchart in Figure 111 describes the internal mechanism
for multichip synchronization in the AD9690. The AD9690
supports several features that aid users in meeting the
requirements set out for capturing a SYSREF± signal. The
SYSREF sample event can be defined as either a synchronous
low to high transition, or a synchronous high to low transition.
Additionally, the AD9690 allows the SYSREF signal to be sampled
using either the rising edge or falling edge of the CLK± input.
The AD9690 also has the ability to ignore a programmable
number (up to 16) of SYSREF± events. The SYSREF± control
options can be selected using Register 0x120 and Register 0x121.
Rev. 0 | Page 56 of 77
Data Sheet
AD9690
START
INCREMENT
SYSREF± IGNORE
COUNTER
NO
NO
RESET
SYSREF± IGNORE
COUNTER
SYSREF±
ENABLED?
(0x120)
NO
NO
SYSREF±
ASSERTED?
YES
UPDATE
SETUP/HOLD
DETECTOR STATUS
(0x128)
YES
SYSREF±
IGNORE
COUNTER
EXPIRED?
(0x121)
YES
ALIGN CLOCK
DIVIDER
PHASE TO
SYSREF
INPUT
CLOCK
DIVIDER
ALIGNMENT
REQUIRED?
YES
YES
NO
SYNCHRONIZATION
MODE?
(0x1FF)
CLOCK
DIVIDER
AUTO ADJUST
ENABLED?
(0x10D)
NO
TIMESTAMP
MODE
SYSREF±
TIMESTAMP
DELAY
(0x123)
INCREMENT
SYSREF±
COUNTER
(0x12A)
CLOCK
DIVIDER
> 1?
(0x10B)
YES
NO
SYSREF±
CONTROL BITS?
(0x559, 0x55A,
0x58F)
YES
SYSREF±
INSERTED
IN JESD204B
CONTROL BITS
NO
RAMP
TEST
MODE
ENABLED?
(0x550)
NORMAL
MODE
YES
SYSREF± RESETS
RAMP TEST
MODE
GENERATOR
BACK TO START
NO
YES
ALIGN PHASE
OF ALL
INTERNAL CLOCKS
(INCLUDING LMFC)
TO SYSREF±
SEND INVALID
8-BIT/10-BIT
CHARACTERS
(ALL 0's)
SYNC~
ASSERTED
NO
SEND K28.5
CHARACTERS
NORMAL
JESD204B
INITIALIZATION
NO
NO
SIGNAL
MONITOR
ALIGNMENT
ENABLED?
(0x26F)
YES
YES
ALIGN SIGNAL
MONITOR
COUNTERS
DDC NCO
ALIGNMENT
ENABLED?
(0x300)
YES
NO
Figure 111. Multichip Synchronization
Rev. 0 | Page 57 of 77
ALIGN DDC
NCO PHASE
ACCUMULATOR
BACK TO START
12834-111
JESD204B
LMFC
ALIGNMENT
REQUIRED?
AD9690
Data Sheet
SYSREF± SETUP/HOLD WINDOW MONITOR
To ensure a valid SYSREF signal capture, the AD9690 has a
SYSREF± setup/hold window monitor. This feature allows the
system designer to determine the location of the SYSREF± signals
relative to the CLK± signals by reading back the amount of
setup/hold margin on the interface through the memory map.
Figure 112 and Figure 113 show the setup and hold status values
for different phases of SYSREF±. The setup detector returns the
status of the SYSREF± signal before the CLK± edge and the
hold detector returns the status of the SYSREF signal after the
CLK± edge. Register 0x128 stores the status of SYSREF± and
lets the user know if the SYSREF± signal is captured by the ADC.
0xF
0xE
0xD
0xC
0xB
0xA
0x9
REG 0x128[3:0] 0x8
0x7
0x6
0x5
0x4
0x3
0x2
0x1
0x0
CLK±
INPUT
VALID
SYSREF±
INPUT
FLIP-FLOP
HOLD (MIN)
FLIP-FLOP
HOLD (MIN)
Figure 112. SYSREF± Setup Detector
Rev. 0 | Page 58 of 77
12834-112
FLIP-FLOP
SETUP (MIN)
Data Sheet
AD9690
REG 0x128[7:4]
0xF
0xE
0xD
0xC
0xB
0xA
0x9
0x8
0x7
0x6
0x5
0x4
0x3
0x2
0x1
0x0
CLK±
INPUT
SYSREF±
INPUT
FLIP-FLOP
SETUP (MIN)
FLIP-FLOP
HOLD (MIN)
FLIP-FLOP
HOLD (MIN)
12834-113
VALID
Figure 113. SYSREF± Hold Detector
Table 28 shows the description of the contents of Register 0x128 and how to interpret them.
Table 28. SYSREF± Setup/Hold Monitor, Register 0x128
Register 0x128[7:4]
Hold Status
0x0
0x0 to 0x8
0x8
0x8
0x9 to 0xF
0x0
Register 0x128[3:0]
Setup Status
0x0 to 0x7
0x8
0x9 to 0xF
0x0
0x0
0x0
Description
Possible setup error. The smaller this number, the smaller the setup margin.
No setup or hold error (best hold margin).
No setup or hold error (best setup and hold margin).
No setup or hold error (best setup margin).
Possible hold error. The larger this number, the smaller the hold margin.
Possible setup or hold error.
Rev. 0 | Page 59 of 77
AD9690
Data Sheet
TEST MODES
ADC TEST MODES
The AD9690 has various test options that aid in the system level
implementation. The AD9690 has ADC test modes that are
available in Register 0x550. These test modes are described in
Table 29. When an output test mode is enabled, the analog section
of the ADC is disconnected from the digital back-end blocks,
and the test pattern is run through the output formatting block.
Some of the test patterns are subject to output formatting, and
some are not. The PN generators from the PN sequence tests
can be reset by setting Bit 4 or Bit 5 of Register 0x550. These
tests can be performed with or without an analog signal (if
present, the analog signal is ignored); however, they do require
an encode clock. For more information, see the AN-877
Application Note, Interfacing to High Speed ADCs via SPI.
Table 29. ADC Test Modes1
Output Test Mode
Bit Sequence
0000
0001
0010
0011
0100
0101
0110
0111
1000
Pattern Name
Off (default)
Midscale short
+Full-scale short
−Full-scale short
Checkerboard
PN sequence long
PN sequence short
One-/zero-word toggle
User input
Expression
N/A
00 0000 0000 0000
01 1111 1111 1111
10 0000 0000 0000
10 1010 1010 1010
X23 + X18 + 1
X9 + X5 + 1
11 1111 1111 1111
Register 0x551 to
Register 0x558
1111
Ramp Output
(X) % 214
1
Default/
Seed Value
N/A
N/A
N/A
N/A
N/A
0x3AFF
0x0092
N/A
N/A
N/A
N/A means not applicable.
Rev. 0 | Page 60 of 77
Sample (N, N + 1, N + 2, …)
N/A
N/A
N/A
N/A
0x1555, 0x2AAA, 0x1555, 0x2AAA, 0x1555
0x3FD7, 0x0002, 0x26E0, 0x0A3D, 0x1CA6
0x125B, 0x3C9A, 0x2660, 0x0c65, 0x0697
0x0000, 0x3FFF, 0x0000, 0x3FFF, 0x0000
User Pat 1[15:2], User Pat 2[15:2], User Pat 3[15:2],
User Pat 4[15:2], User Pat 1[15:2] … for repeat mode
User Pat 1[15:2], User Pat 2[15:2], User Pat 3[15:2],
User Pat 4[15:2], 0x0000 … for single mode
(X) % 214, (X +1) % 214, (X +2) % 214, (X +3) % 214
Data Sheet
AD9690
JESD204B BLOCK TEST MODES
In addition to the ADC pipeline test modes, the AD9690 also has
flexible test modes in the JESD204B block. These test modes are
listed in Register 0x573 and Register 0x574. These test patterns
can be injected at various points along the output data path. These
test injection points are shown in Figure 98. Table 30 describes
the various test modes available in the JESD204B block. For the
AD9690, a transition from test modes (Register 0x573 ≠ 0x00)
to normal mode (Register 0x573 = 0x00) requires an SPI soft
reset. This is done by writing 0x81 to Register 0x00 (self cleared).
Transport Layer Sample Test Mode
The transport layer samples are implemented in the AD9690 as
defined by section 5.1.6.3 in the JEDEC JESD204B Specification.
These tests are shown in Register 0x571[5]. The test pattern is
equivalent to the raw samples from the ADC.
Interface Test Modes
The interface test modes are described in Register 0x573 Bits[3:0].
These test modes are also explained in Table 30. The interface tests
can be injected at various points along the data. See Figure 98
for more information on the test injection points. Register 0x573
Bits[5:4] show where these tests are injected.
Table 31, Table 32, and Table 33 show examples of some of the
test modes when injected at the JESD Sample Input, PHY 10-bit
Input, and Scrambler 8-bit Input. UP in the tables represent the
user pattern control bits from the customer register map.
Table 30. JESD204B Interface Test Modes
Output Test Mode
Bit Sequence
0000
0001
0010
0011
0100
0101
0110
0111
1000
1110
1111
Pattern Name
Off (default)
Alternating checker board
1/0 word toggle
31-bit PN sequence
23-bit PN sequence
15-bit PN sequence
9-bit PN sequence
7-bit PN sequence
Ramp output
Continuous/repeat user test
Single user test
Expression
Not applicable
0x5555, 0xAAAA, 0x5555, …
0x0000, 0xFFFF, 0x0000, …
X31 + X28 + 1
X23 + X18 + 1
X15 + X14 + 1
X9 + X5 + 1
X7 + X6 + 1
(X) % 216
Register 0x551 to Register 0x558
Register 0x551 to Register 0x558
Default
Not applicable
Not applicable
Not applicable
0x0003AFFF
0x003AFF
0x03AF
0x092
0x07
Ramp size depends on test injection point
User Pat 1 to User Pat 4, then repeat
User Pat 1 to User Pat 4, then zeroes
Table 31. JESD204B Sample Input for M=1, S=2, N'=16 (Register 0x573[5:4]='b00)
Frame
Number
0
0
1
1
2
2
3
3
4
4
Converter
Number
0
0
0
0
0
0
0
0
0
0
Sample
Number
0
1
0
1
0
1
0
1
0
1
Alternating
Checkerboard
0x5555
0x5555
0xAAAA
0xAAAA
0x5555
0x5555
0xAAAA
0xAAAA
0x5555
0x5555
1/0 Word
Toggle
0x0000
0x0000
0xFFFF
0xFFFF
0x0000
0x0000
0xFFFF
0xFFFF
0x0000
0x0000
Ramp
(X) % 216
(X) % 216
(X +1) % 216
(X +1) % 216
(X +2) % 216
(X +2) % 216
(X +3) % 216
(X +3) % 216
(X +4) % 216
(X +4) % 216
Rev. 0 | Page 61 of 77
PN9
0x496F
0x496F
0xC9A9
0xC9A9
0x980C
0x980C
0x651A
0x651A
0x5FD1
0x5FD1
PN23
0xFF5C
0xFF5C
0x0029
0x0029
0xB80A
0xB80A
0x3D72
0x3D72
0x9B26
0x9B26
User Repeat
UP1[15:0]
UP1[15:0]
UP2[15:0]
UP2[15:0]
UP3[15:0]
UP3[15:0]
UP4[15:0]
UP4[15:0]
UP1[15:0]
UP1[15:0]
User Single
UP1[15:0]
UP1[15:0]
UP2[15:0]
UP2[15:0]
UP3[15:0]
UP3[15:0]
UP4[15:0]
UP4[15:0]
0x0000
0x0000
AD9690
Data Sheet
Table 32. Physical Layer 10-bit Input (Register 0x573[5:4]='b01)
10-Bit Symbol
Number
0
1
2
3
4
5
6
7
8
9
10
11
Alternating
Checkerboard
0x155
0x2AA
0x155
0x2AA
0x155
0x2AA
0x155
0x2AA
0x155
0x2AA
0x155
0x2AA
1/0 Word
Toggle
0x000
0x3FF
0x000
0x3FF
0x000
0x3FF
0x000
0x3FF
0x000
0x3FF
0x000
0x3FF
Ramp
(X) % 210
(X + 1) % 210
(X + 2) % 210
(X + 3) % 210
(X + 4) % 210
(X + 5) % 210
(X + 6) % 210
(X + 7) % 210
(X + 8) % 210
(X + 9) % 210
(X + 10) % 210
(X + 11) % 210
PN9
0x125
0x2FC
0x26A
0x198
0x031
0x251
0x297
0x3D1
0x18E
0x2CB
0x0F1
0x3DD
PN23
0x3FD
0x1C0
0x00A
0x1B8
0x028
0x3D7
0x0A6
0x326
0x10F
0x3FD
0x31E
0x008
User Repeat
UP1[15:6]
UP2[15:6]
UP3[15:6]
UP4[15:6]
UP1[15:6]
UP2[15:6]
UP3[15:6]
UP4[15:6]
UP1[15:6]
UP2[15:6]
UP3[15:6]
UP4[15:6]
User Single
UP1[15:6]
UP2[15:6]
UP3[15:6]
UP4[15:6]
0x000
0x000
0x000
0x000
0x000
0x000
0x000
0x000
Table 33. Scrambler 8-bit Input (Register 0x573[5:4]='b10)
8-Bit Octet
Number
0
1
2
3
4
5
6
7
8
9
10
11
Alternating
Checkerboard
0x55
0xAA
0x55
0xAA
0x55
0xAA
0x55
0xAA
0x55
0xAA
0x55
0xAA
1/0 Word
Toggle
0x00
0xFF
0x00
0xFF
0x00
0xFF
0x00
0xFF
0x00
0xFF
0x00
0xFF
Ramp
(X) % 28
(X + 1) % 28
(X + 2) % 28
(X + 3) % 28
(X + 4) % 28
(X + 5) % 28
(X + 6) % 28
(X + 7) % 28
(X + 8) % 28
(X + 9) % 28
(X + 10) % 28
(X + 11) % 28
Data Link Layer Test Modes
The data link layer test modes are implemented in the AD9690
as defined by section 5.3.3.8.2 in the JEDEC JESD204B
Specification. These tests are shown in Register 0x574 Bits[2:0].
PN9
0x49
0x6F
0xC9
0xA9
0x98
0x0C
0x65
0x1A
0x5F
0xD1
0x63
0xAC
PN23
0xFF
0x5C
0x00
0x29
0xB8
0x0A
0x3D
0x72
0x9B
0x26
0x43
0xFF
User Repeat
UP1[15:9]
UP2[15:9]
UP3[15:9]
UP4[15:9]
UP1[15:9]
UP2[15:9]
UP3[15:9]
UP4[15:9]
UP1[15:9]
UP2[15:9]
UP3[15:9]
UP4[15:9]
User Single
UP1[15:9]
UP2[15:9]
UP3[15:9]
UP4[15:9]
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
Test patterns inserted at this point are useful for verifying the
functionality of the data link layer. When the data link layer
test modes are enabled, disable SYNCINB± by writing 0xC0
to Register 0x572.
Rev. 0 | Page 62 of 77
Data Sheet
AD9690
SERIAL PORT INTERFACE
The AD9690 SPI allows the user to configure the converter for
specific functions or operations through a structured register
space provided inside the ADC. The SPI gives the user added
flexibility and customization, depending on the application.
Addresses are accessed via the serial port and can be written to
or read from via the port. Memory is organized into bytes that
can be further divided into fields. These fields are documented
in the Memory Map section. For detailed operational information,
see the Serial Control Interface Standard (Rev. 1.0).
CONFIGURATION USING THE SPI
Three pins define the SPI of the AD9690 ADC: the SCLK pin,
the SDIO pin, and the CSB pin (see Table 34). The SCLK (serial
clock) pin is used to synchronize the read and write data presented
from/to the ADC. The SDIO (serial data input/output) pin is a
dual-purpose pin that allows data to be sent and read from the
internal ADC memory map registers. The CSB (chip select bar)
pin is an active low control that enables or disables the read and
write cycles.
Table 34. Serial Port Interface Pins
Pin
SCLK
SDIO
CSB
Function
Serial clock. The serial shift clock input, which is used to
synchronize serial interface, reads, and writes.
Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
Chip select bar. An active low control that gates the read
and write cycles.
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing. An example of the
serial timing and its definitions can be found in Figure 4 and
Table 5.
Other modes involving CSB are available. The CSB can be held
low indefinitely, which permanently enables the device; this is
called streaming. The CSB can stall high between bytes to allow
additional external timing. When CSB is tied high, SPI functions
are placed in a high impedance mode. This mode turns on any
SPI pin secondary functions.
All data is composed of 8-bit words. The first bit of each individual
byte of serial data indicates whether a read or write command is
issued, which allows the SDIO pin to change direction from an
input to an output.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the SDIO pin to change
direction from an input to an output at the appropriate point in
the serial frame.
Data can be sent in MSB first mode or in LSB first mode. MSB
first is the default on power-up and can be changed via the SPI
port configuration register. For more information about this
and other features, see the Serial Control Interface Standard
(Rev. 1.0).
HARDWARE INTERFACE
The pins described in Table 34 comprise the physical interface
between the user programming device and the serial port of the
AD9690. The SCLK pin and the CSB pin function as inputs
when using the SPI interface. The SDIO pin is bidirectional,
functioning as an input during write phases and as an output
during readback.
The SPI interface is flexible enough to be controlled by either
FPGAs or microcontrollers. One method for SPI configuration
is described in detail in the AN-812 Application Note,
Microcontroller-Based Serial Port Interface (SPI) Boot Circuit.
Do not activate the SPI port during periods when the full
dynamic performance of the converter is required. Because the
SCLK signal, the CSB signal, and the SDIO signal are typically
asynchronous to the ADC clock, noise from these signals can
degrade converter performance. If the on-board SPI bus is
used for other devices, it may be necessary to provide buffers
between this bus and the AD9690 to prevent these signals from
transitioning at the converter inputs during critical sampling
periods.
SPI ACCESSIBLE FEATURES
Table 35 provides a brief description of the general features that
are accessible via the SPI. These features are described in detail
in the Serial Control Interface Standard (Rev. 1.0). The AD9690
device-specific features are described in the Memory Map section.
Table 35. Features Accessible Using the SPI
Feature
Name
Mode
Clock
DDC
Test
Input/Output
Output Mode
SERDES
Output
Setup
Rev. 0 | Page 63 of 77
Description
Allows the user to set either power-down mode or
standby mode.
Allows the user to access the clock divider via
the SPI.
Allows the user to set up decimation filters for
different applications.
Allows the user to set test modes to have known
data on output bits.
Allows the user to set up outputs.
Allows the user to vary SERDES settings such as
swing and emphasis.
AD9690
Data Sheet
MEMORY MAP
READING THE MEMORY MAP REGISTER TABLE
Each row in the memory map register table has eight bit
locations. The memory map is divided into four sections: the
Analog Devices SPI registers (Register 0x000 to Register 0x00D),
the analog input buffer control registers, the ADC function
registers, the DDC function registers, and the digital outputs
and test modes registers.
Table 36 (see the Memory Map Register Table section) documents
the default hexadecimal value for each hexadecimal address shown.
The column with the heading Bit 7 (MSB) is the start of the
default hexadecimal value given. For example, Address 0x561,
the output mode register, has a hexadecimal default value of
0x01, which means that Bit 0 = 1, and the remaining bits are 0s.
This setting is the default output format value, which is twos
complement. For more information on this function and others,
see the Table 36.
Open and Reserved Locations
All address and bit locations that are not included in Table 36
are not currently supported for this device. Write unused bits of
a valid address location with 0s unless the default value is set
otherwise. Writing to these locations is required only when part
of an address location is unassigned (for example, Address 0x561).
If the entire address location is open (for example, Address 0x13),
do not write to this address location.
Default Values
After the AD9690 is reset, critical registers are loaded with
default values. The default values for the registers are given in
the memory map register table, Table 36.
Logic Levels
An explanation of logic level terminology follows:
•
•
•
“Bit is set” is synonymous with “bit is set to Logic 1” or
“writing Logic 1 for the bit.”
“Clear a bit” is synonymous with “bit is set to Logic 0” or
“writing Logic 0 for the bit.”
X denotes a don’t care bit.
SPI Soft Reset
After issuing a soft reset by programming 0x81 to Register 0x000,
the AD9690 requires 5 ms to recover. When programming the
AD9690 for application setup, ensure that an adequate delay is
programmed into the firmware after asserting the soft reset and
before starting the device setup.
Rev. 0 | Page 64 of 77
Data Sheet
AD9690
MEMORY MAP REGISTER TABLE
All address locations that are not included in Table 36 are not currently supported for this device and should not be written.
Table 36. Memory Map Registers
Reg
Addr
Register
Bit 7
(Hex)
Name
(MSB)
Analog Devices SPI Registers
INTERFACE_
Soft reset
0x000
CONFIG_A
(self
clearing)
INTERFACE_
Single
0x001
CONFIG_B
instruction
0x002
DEVICE_
CONFIG
0x003
CHIP_TYPE
0
CHIP_ID (low
1
byte)
CHIP_ID
0x005
0
(high byte)
CHIP_
0x006
GRADE
0x008
Device index
0
0x00A
Scratch pad
0
0x00B
SPI revision
0
Vendor ID
0x00C
0
(low byte)
Vendor ID
0x00D
0
(high byte)
Analog Input Buffer Control Registers
0x015
Analog input
0
0x004
0x016
Input
termination
0x934
Input
capacitance
Buffer
Control 1
0x018
0x019
Buffer
Control 2
0
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
LSB first
0 = MSB
1 = LSB
0
Address
ascension
0
0
Address
ascension
0
0
0
0
0
0
0
Bit 1
Bit 0 (LSB)
Default
Soft reset
LSB first
(self
0 = MSB
clearing)
1 = LSB
Datapath
0
0
soft reset
(self
clearing)
00 = normal operation
0
10 = standby
11 = power-down
011 = high speed ADC
0x03
0x00
0x00
0x00
1
0
0
0
1
0
1
0xD6
0
0
0
0
0
0
0
0x00
X
X
X
X
1010 = 1000 MSPS
0101 = 500 MSPS
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
0
0
0
0
1
0
0
0
1
1
0
1
0
0x01
0x00
0x01
0x56
0
0
0
0
1
0
0
0x04
0
0
0
0
0
0
Input
disable
0 = normal
operation
1 = input
disabled
0x00
1110 = AD9690-1000
1100 = AD9690-500
Analog input differential termination
0000 = 400 Ω (default)
0001 = 200 Ω
0010 = 100 Ω
0110 = 50 Ω
0
0
0000 = 1.0× buffer current
0001 = 1.5× buffer current
0010 = 2.0× buffer current (default for AD9690-500)
0011 = 2.5× buffer current
0100 = 3.0× buffer current (default for AD9690-1000)
0101 = 3.5× buffer current
…
1111 = 8.5× buffer current
0100 = setting 1
0101 = setting 2 (default for AD9690-1000)
0110 = setting 3 (default for AD9690-500)
0111 = setting 4
0x1F = 3 pF to GND (default)
0x00 = 1.5 pF to GND
0100 = AD9690-1000
0010 = AD9690-500
0
Rev. 0 | Page 65 of 77
0
0
0x1F
0x44 for
AD9690
-1000;
0x22 for
AD9690
-500
0
Notes
0x50 for
AD9690
-1000;
0x60 for
AD9690
-500
Read
only
Read
only
Read
only
Read
only
Reserved
Read
only
Read
only
AD9690
Reg
Addr
(Hex)
0x01A
Data Sheet
Register
Name
Buffer
Control 3
Bit 7
(MSB)
0
Bit 6
0
Bit 5
0
Bit 4
0
Bit 3
0x11A
Buffer
Control 4
0
0
0
0
0x935
Buffer
Control 5
0
0
High
frequency
setting
0 = OFF
(default)
1 = ON
0
0
0
0x025
Input fullscale range
0
0
0
0
0x030
Input fullscale control
0
0
0
Full-scale control
See Table 10 for recommended settings
for different frequency bands;
default values:
AD9690-1000 = 110
AD9690-500 = 001
AD9690-500 = 110 (for <1.82 V)
0
0
0
0
0
0
0
0
0
0x00
0
0
0
0
0
0
0
1.0 V
reference
select
0=
internal
1=
external
Diode
selection
0=
no diode
selected
1=
temperature
diode
selected
0
Fast Detect (FD)
000 = Fast Detect output
001 = JESD204B LMFC output
010 = JESD204B internal SYNC~ output
011 = temperature diode
111 = disabled
000 = divide by −1
001 = divide by 2
011 = divide by 4
111 = divide by 8
0x3F
ADC Function Registers
V_1P0
0x024
control
0x028
Temperature
diode
0
0x03F
PDWN/
STBY pin
control
0
0x040
Chip pin
control
0 = PDWN/ 0
STBY
enabled
1=
disabled
PDWN/STBY function
00 = power down
01 = standby
10 = disabled
0x10B
Clock divider
0
0
0
Bit 2
Bit 1
Bit 0 (LSB)
1000 = setting 1
1001 = setting 2 (default for AD9690-1000)
1010 = setting 3 (default for AD9690-500)
0
0
0
Rev. 0 | Page 66 of 77
0
Notes
0x0A for
AD9690
-1000;
0x0C for
AD9690
-500
V p-p
differential;
use in
conjunction with
Reg.
0x030
Used in
conjunction with
Reg.
0x025
0
Low
0
0
Frequency
Operation
0 = off
1 = on
(default)
Full-scale adjust
0000 = 1.94 V
1000 = 1.46 V
1001 = 1.58 V
1010 = 1.70 V (default for AD9690-1000)
1011 = 1.82 V
1100 = 2.06 V (default for AD9690-500)
111 = Reserved
0
0
Default
0x09 for
AD9690
-1000;
0x0A for
AD9690
-500
0
0x00
Used in
conjunction with
Reg.
0x040
0x00
Used in
conjunction with
Reg.
0x040
0x00
Data Sheet
Reg
Addr
(Hex)
0x10C
Register
Name
Clock divider
phase
0x10D
Clock divider
and SYSREF
control
0x117
Clock delay
control
0x118
Clock fine
delay
0x11C
Clock status
0x120
SYSREF±
Control 1
0x121
SYSREF±
Control 2
0x123
SYSREF±
timestamp
delay control
0x128
SYSREF±
Status 1
AD9690
Bit 7
(MSB)
0
Bit 6
0
Bit 5
0
Bit 4
0
Bit 3
Bit 2
Bit 1
Bit 0 (LSB)
Independently controls ADC clock divider phase offset
0000 = 0 input clock cycles delayed
0001 = ½ input clock cycles delayed
0010 = 1 input clock cycles delayed
0011 = 1½ input clock cycles delayed
0100 = 2 input clock cycles delayed
0101 = 2½ input clock cycles delayed
…
1111 = 7½ input clock cycles delayed
Clock divider positive skew
Clock divider negative
Clock
0
0
0
window
skew window
divider auto
00 = no positive skew
00 = no negative skew
phase
01 = 1 device clock of
01 = 1 device clock of
adjust
positive skew
negative skew
0=
10 = 2 device clocks of
10 = 2 device clocks of
disabled
positive skew
negative skew
1 = enabled
11 = 3 device clocks of
11 = 3 device clocks of
positive skew
negative skew
Clock fine
0
0
0
0
0
0
0
delay
adjust
enable
0=
disabled
1=
enabled
Clock fine delay adjust[7:0],
twos complement coded control to adjust the fine sample clock skew in ~1.7 ps steps
≤ −88 = −151.7 ps skew
−87 = −150 ps skew
…
0 = 0 ps skew
…
≥ +87 = +150 ps skew
0 = no
0
0
0
0
0
0
0
input
clock
detected
1 = input
clock
detected
SYSREF± mode select
CLK±
SYSREF±
SYSREF± 0
0
0
00 = disabled
edge
transition
flag
01 = continuous
select
select
reset
10 = N shot
0 = rising
0 = low to
0=
1 = falling
high
normal
1 = high to
operatlow
ion
1 = flags
held in
reset
SYSREF N-shot ignore counter select
0
0
0
0
0000 = next SYSREF± only
0001 = ignore the first SYSREF± transitions
0010 = ignore the first two SYSREF± transitions
…
1111 = ignore the first 16 SYSREF± transitions
SYSREF± timestamp delay, Bits[6:0]
0x00 = no delay
0x01 = 1 clock delay
…
0x7F = 127 clocks delay
SYSREF± hold status, Register 0x128[7:4],
SYSREF± setup status, Register 0x128[3:0],
refer to Table 28
refer to Table 28
Rev. 0 | Page 67 of 77
Default
0x00
Notes
0x00
Clock
divider
must be
>1
0x00
Enabling
the clock
fine
delay
adjust
causes a
datapath
reset
Used in
conjunction
with Reg.
0x0117
0x00
Read
only
0x00
0x00
0x00
Read
only
Mode
select
(Reg
0x120,
Bits [2:1])
must be
N-shot
Ignored
when
Reg.
0x01FF
= 0x00
AD9690
Reg
Addr
(Hex)
0x129
0x12A
0x1FF
Register
Name
SYSREF± and
clock divider
status
Data Sheet
Bit 7
(MSB)
0
Bit 6
0
SYSREF±
counter
Chip sync
mode
0x200
Chip
application
mode
0
0
0x201
Chip
decimation
ratio
0
0
0x228
Customer
offset
Fast detect
(FD) control
0x245
0x247
0x248
0x249
0x24A
0x24B
0
FD upper
threshold
LSB
FD upper
threshold
MSB
FD lower
threshold
LSB
FD lower
threshold
MSB
FD dwell
time LSB
Bit 5
0
Bit 3
Bit 2
Bit 1
Bit 0 (LSB)
Clock divider phase when SYSREF± was captured
0000 = in-phase
0001 = SYSREF± is ½ cycle delayed from clock
0010 = SYSREF± is 1 cycle delayed from clock
0011 = 1½ input clock cycles delayed
0100 = 2 input clock cycles delayed
0101 = 2½ input clock cycles delayed
…
1111 = 7½ input clock cycles delayed
SYSREF counter, Bits[7:0] increments when a SYSREF± is captured
Chip Q
ignore
0=
normal
(I/Q)
1 = ignore
(I – only)
0
0
0
0
Synchronization mode
00 = normal
01 = timestamp
Chip operating mode
00 = full bandwidth
mode
01 = DDC 0 on
10 = DDC 0 and DDC 1
on
Chip decimation ratio select
000 = full sample rate (decimate = 1)
001 = decimate by 2
010 = decimate by 4
011 = decimate by 8
100 = decimate by 16
Offset adjust in LSBs from +127 to −128 (twos complement format)
0
0
Bit 4
0
0
Force value of
Force FD
FD pin if force
pin;
0 = normal pins is true,
this value is
function;
output on FD
1 = force
pin
to value
Fast detect upper threshold, Bits[7:0]
0
0
0
0
0
0
Enable
fast detect
output
0
Fast detect upper threshold, Bits[12:8]
0
Read
only
0x00
0x00
0x00
0x00
0x00
0x00
0x00
Fast detect lower threshold, Bits[12:8]
0x00
Fast detect dwell time, Bits[7:0]
0x00
Fast detect dwell time, Bits[15:8]
0x00
0x24C
FD dwell
time MSB
0x26F
Signal
monitor
synchronization control
0
0
0
0
0
0
0x270
Signal
monitor
control
0
0
0
0
0
0
Rev. 0 | Page 68 of 77
Notes
0x00
Fast detect lower threshold, Bits[7:0]
0
Default
Read
only
Synchronization mode
00 = disabled
01 = continuous
11 = one shot
Peak
detector
0=
disabled
1=
enabled
0
0x00
0x00
Refer to
the
Signal
Monitor
section
Data Sheet
Reg
Addr
(Hex)
0x271
Register
Name
Signal
Monitor
Period
Register 0
AD9690
Bit 7
(MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Signal monitor period, Bits[7:0]
Bit 1
Bit 0 (LSB)
Default
0x80
Notes
In decimated
output
clock
cycles
In decimated
output
clock
cycles
In decimated
output
clock
cycles
0x272
Signal
Monitor
Period
Register 1
Signal monitor period, Bits[15:8]
0x273
Signal
Monitor
Period
Register 2
Signal monitor period, Bits[23:16]
0x274
Signal
monitor
result control
0x275
Signal
Monitor
Result
Register 0
Signal monitor result, Bits[7:0]
When Register 0x0274[0] = 1, result bits [19:7] = peak detector absolute value [12:0]; result bits [6:0] = 0
Read
only
Updated
based on
Reg.
0x274[4]
0x276
Signal
Monitor
Result
Register 1
Signal monitor result, Bits[15:8]
Read
only
Updated
based on
Reg.
0x274[4]
0x277
Signal
Monitor
Result
Register 1
0
Read
only
Updated
based on
Reg.
0x274[4]
0x278
Signal
monitor
period
counter
result
Signal
monitor
SPORT over
JESD204B
control
SPORT over
JESD204B
input
selection
Read
only
Updated
based on
Reg.
0x274[4]
0x279
0x27A
0
0
0
0
0
0
Result
update
1 = update
results (self
clear)
0
0
0x00
0x00
Result
selection
0=
reserved
1 = peak
detector
0
Signal monitor result, Bits[19:16]
Period count result, Bits[7:0]
0
0
0
0
0
0
0
0
0
0
0
0
DDC Function Registers (See the Digital Downconverter (DDC) Section)
DDC synch
DDC NCO
0x300
0
0
0
control
soft reset
0 = normal
operation
1 = reset
0
Rev. 0 | Page 69 of 77
0
00 = reserved
11 = enable
Peak
detector
0=
disabled
1=
enabled
0
Synchronization mode
(triggered by SYSREF±)
00 = disabled
01 = continuous
11 = 1-shot
0x01
0x00
0x00
AD9690
Reg
Addr
(Hex)
0x310
Data Sheet
Register
Name
DDC 0
control
Bit 7
(MSB)
Mixer
select
0 = real
mixer
1=
complex
mixer
Bit 6
Gain
select
0 = 0 dB
gain
1 = 6 dB
gain
0x311
DDC 0 input
selection
0
0
0x314
DDC 0
frequency
LSB
DDC0
frequency
MSB
DDC 0 phase
LSB
DDC 0 phase
MSB
DDC 0
output test
mode
selection
0x315
0x320
0x321
0x327
X
X
X
X
0
0
DDC 1
control
Mixer
select
0 = real
mixer
1=
complex
mixer
Gain
select
0 = 0 dB
gain
1 = 6 dB
gain
0x331
DDC 1 input
selection
0
0
0x334
DDC 1
frequency
LSB
DDC 1
frequency
MSB
DDC 1 phase
LSB
DDC 1 phase
MSB
DDC 1
output test
mode
selection
0x340
0x341
0x347
Bit 3
Complex
to real
enable
0=
disabled
1=
enabled
Bit 2
0
Bit 1
Bit 0 (LSB)
Decimation rate select
(complex—real disabled)
11 = decimate by 2
00 = decimate by 4
01 = decimate by 8
10 = decimate by 16
(complex—real enabled)
11 = decimate by 1
00 = decimate by 2
01 = decimate by 4
10 = decimate by 8
0
0
0
0
DDC 0 NCO frequency value, Bits[7:0]
twos complement
0x330
0x335
Bit 5
Bit 4
IF (intermediate
frequency) mode
00 = variable IF mode
(mixers and NCO
enabled)
01 = 0 Hz IF mode (mixer
bypassed, NCO disabled)
10 = fADC/4 Hz IF mode
(fADC/4 down-mixing
mode)
11 = test mode (mixer
inputs forced to +FS,
NCO enabled)
0
0
X
X
DDC 0 NCO frequency value, Bits[11:8]
twos complement
DDC 0 NCO phase value, Bits[7:0]
twos complement
DDC 0 NCO phase value, Bits[11:8]
X
X
twos complement
I output
0
0
0
0
0
test mode
enable
0=
disabled
1=
enabled
IF (intermediate
Decimation rate select
Complex
0
frequency) mode
(complex—real disabled)
to real
00 = variable IF mode
11 = decimate by 2
enable
(mixers and NCO
00 = decimate by 4
0=
enabled)
01 = decimate by 8
disabled
01 = 0 Hz IF mode(mixer
10 = decimate by 16
1=
bypassed, NCO disabled) enabled
(complex—real enabled)
10 = fADC/4 Hz IF mode
11 = decimate by 1
00 = decimate by 2
(fADC/4 downmixing
01 = decimate by 4
mode)
10 = decimate by 8
11 = test mode (mixer
inputs forced to +FS,
NCO enabled)
0
0
0
0
0
0
DDC 1 NCO frequency value, Bits[7:0]
twos complement
X
X
X
X
X
X
0
0
0
X
DDC 1 NCO frequency value, Bits[11:8]
twos complement
DDC 1 NCO phase value, Bits[7:0]
twos complement
DDC 1 NCO phase value, Bits[11:8]
X
twos complement
I output
0
0
0
0
test mode
enable
0=
disabled
1=
enabled
Rev. 0 | Page 70 of 77
Default
0x00
Notes
0x00
Refer to
the DDC
section
0x00
0x00
0x00
0x00
0x00
Refer to
the DDC
section
0x00
0x00
Refer to
the DDC
section
0x00
0x00
0x00
0x00
0x00
Refer to
the DDC
section
Data Sheet
AD9690
Reg
Addr
Register
Bit 7
(Hex)
Name
(MSB)
Digital Outputs and Test Modes
ADC test
User
0x550
modes
pattern
selection
0 = continuous
repeat
1 = single
pattern
Bit 6
Bit 5
Bit 4
0
Reset PN
long gen
0 = long
PN enable
1 = long
PN reset
Reset PN
short gen
0 = short
PN enable
1 = short
PN reset
Bit 3
Bit 2
Bit 1
Bit 0 (LSB)
Test mode selection
0000 = off, normal operation
0001 = midscale short
0010 = positive full-scale
0011 = negative full-scale
0100 = alternating checker board
0101 = PN sequence, long
0110 = PN sequence, short
0111 = 1/0 word toggle
1000 = the user pattern test mode (used with
Register 0x0550, Bit 7 and user pattern 1, 2, 3, 4
registers)
1111 = ramp output
0
0
0
Default
0x00
0x551
User Pattern
1 LSB
0
0
0
0
0
0x552
User Pattern
1 MSB
0
0
0
0
0
0
0
0
0x00
0x553
User Pattern
2 LSB
0
0
0
0
0
0
0
0
0x00
0x554
User Pattern
2 MSB
0
0
0
0
0
0
0
0
0x00
0x555
User Pattern
3 LSB
0
0
0
0
0
0
0
0
0x00
0x556
User Pattern
3 MSB
0
0
0
0
0
0
0
0
0x00
0x557
User Pattern
4 LSB
0
0
0
0
0
0
0
0
0x00
0x558
User Pattern
4 MSB
0
0
0
0
0
0
0
0
0x00
0x559
Output Mode
Control 1
0
0x55A
Output Mode
Control 2
0
Converter control Bit 1 selection
000 = tie low (1’b0)
001 = overrange bit
011 = fast detect (FD) bit
101 = SYSREF±
Only used when CS (Register 0x58F)
= 2 or 3
0
0
0
0x00
0
Converter control Bit 0 selection
000 = tie low (1’b0)
001 = overrange bit
011 = fast detect (FD) bit
101 = SYSREF±
Only used when CS (Register 0x58F) = 3
0x00
0
Converter control Bit 2 selection
000 = tie low (1’b0)
001 = overrange bit
011 = fast detect (FD) bit
101 = SYSREF
Used when CS (Register 0x58F) = 1, 2, or 3
0x00
Rev. 0 | Page 71 of 77
Notes
Used
with Reg.
0x550
and Reg.
0x573
Used
with Reg.
0x550
and Reg.
0x573
Used
with Reg.
0x550
and Reg.
0x573
Used
with Reg.
0x550
and Reg.
0x573
Used
with Reg.
0x550
and Reg.
0x573
Used
with Reg.
0x550
and Reg.
0x573
Used
with Reg.
0x550
and Reg.
0x573
Used
with Reg.
0x550
and Reg.
0x573
AD9690
Reg
Addr
(Hex)
0x561
Register
Name
Output
mode
Data Sheet
Bit 7
(MSB)
0
Bit 6
0
Bit 5
0
Bit 4
0
0x562
Output
overrange
(OR) clear
0
0
0
0
0x563
Output OR
status
0
0
0
0
0x56E
JESD204B
lane rate
control
0
0
0
0x56F
JESD204B
PLL lock
status
PLL lock
0 = not
locked
1 = locked
0
0
0x570
JESD204B
quick configuration
0x571
JESD204B
Link Mode
Control 1
0x572
JESD204B
Link Mode
Control 2
0x573
JESD204B
Link Mode
Control 3
0 = serial
lane rate
≥6.25 Gbps
and
≤12.5 Gbps
1 = serial
lane rate
must be ≥
3.125 Gbps
and
≤6.25 Gbps
0
Bit 3
0
Virtual
Converter 3 OR
0 = OR bit
enabled
1 = OR bit
cleared
Virtual
Converter 3 OR
0 = no OR
1 = OR
occurred
0
0
Bit 2
Sample
invert
0 = normal
1 = sample
invert
Virtual
Converter 2
OR
0 = OR bit
enabled
1 = OR bit
cleared
Virtual
Converter 2
OR
0 = no OR
1 = OR
occurred
0
0
Bit 1
Bit 0 (LSB)
Data format select
00 = offset binary
01 = twos complement
Virtual
Converter 1
OR
0 = OR bit
enabled
1 = OR bit
cleared
Virtual
Converter 1
OR
0 = no OR
1 = OR
occurred
0
0
Virtual
Converter
0 OR
0 = OR bit
enabled
1 = OR bit
cleared
Virtual
Converter
0 OR
0 = no OR
1 = OR
occurred
0
0x10
0
0x00
JESD204B quick configuration
L = number of lanes = 2Register 0x570, Bits[7:6]
M = number of converters = 2Register 0x570, Bits[5:3]
F = number of octets/frame = 2 Register 0x570, Bits[2:0]
Standby
mode
0 = all
converter
outputs 0
1 = CGS
(/K28.5/)
Tail bit
(t) PN
0=
disable
1=
enable
T = N΄ −
N − CS
SYNCINB± pin control
00 = normal
10 = ignore SYNCINB±
(force CGS)
11 = ignore SYNCINB±
(force ILAS/user data)
CHKSUM mode
00 = sum of all 8-bit link
config registers
01 = sum of individual
link config fields
10 = checksum set to
zero
Long
transport
layer test
0=
disable
1=
enable
SYNCINB±
pin invert
0 = active
low
1 = active
high
Lane synchronization
0 = disable
FACI uses
/K28.7/
1 = enable
FACI uses
/K28.3/ and
/K28.7/
SYNCINB±
pin type
0=
differential
1 = CMOS
Test injection point
00 = N΄ sample input
01 = 10-bit data at
8-bit/10-bit output
(for PHY testing)
10 = 8-bit data at
scrambler input
ILAS sequence mode
00 = ILAS disabled
01 = ILAS enabled
11 = ILAS always on test
mode
0
FACI
0=
enabled
1=
disabled
Link
control
0 = active
1 = power
down
8-/10-bit
0
bit invert
0=
normal
1 = invert
the abcd
efghij
symbols
JESD204B test mode patterns
0000 = normal operation (test mode disabled)
0001 = alternating checker board
0010 = 1/0 word toggle
0011 = 31-bit PN sequence—X31 + X28 + 1
0100 = 23-bit PN sequence—X23 + X18 + 1
0101 = 15-bit PN sequence—X15 + X14 + 1
0110 = 9-bit PN sequence—X9 + X5 + 1
0111 = 7-bit PN sequence—X7 + X6 + 1
1000 = ramp output
1110 = continuous/repeat user test
1111 = single user test
Rev. 0 | Page 72 of 77
8-bit/10-bit
bypass
0 = normal
1 = bypass
Default
0x01
Notes
0x00
0x00
0x80 for
AD96901000;
0x40 for
AD9690500
0x14
0x00
0x00
Read
only
Read
only
Refer to
Table 26
and
Table 27
Data Sheet
Reg
Addr
(Hex)
0x574
0x578
0x580
0x581
0x583
0x584
0x585
0x586
0x58B
Register
Name
JESD204B
Link Mode
Control 4
JESD204B
LMFC offset
JESD204B
DID config
JESD204B
BID config
JESD204B LID
Config 1
JESD204B LID
Config 2
JESD204B LID
Config 3
JESD204B LID
Config 4
JESD204B
parameters
SCR/L
AD9690
Bit 7
(MSB)
Bit 6
Bit 5
Bit 4
ILAS delay
0000 = transmit ILAS on first LMFC after SYNCINB±
deasserted
0001 = transmit ILAS on second LMFC after
SYNCINB± deasserted
…
1111 = transmit ILAS on 16th LMFC after SYNCINB±
deasserted
0
0
0
Bit 2
Bit 1
Bit 0 (LSB)
Link layer test mode
000 = normal operation (link layer test
mode disabled)
001 = continuous sequence of /D21.5/
characters
100 = modified RPAT test sequence
101 = JSPAT test sequence
110 = JTSPAT test sequence
LMFC phase offset value[4:0]
JESD204B Tx DID value[7:0]
0x00
0
0
0
0
Lane 0 LID value, Bits[4:0]
0x00
0
0
0
Lane 1 LID value, Bits[4:0]
0x01
0
0
0
Lane 2 LID value, Bits[4:0]
0x01
0
0
0
Lane 3 LID value, Bits[4:0]
0x03
JESD204B
scrambling
(SCR)
0=
disabled
1=
enabled
0
0
0
JESD204B Tx BID value, Bits[3:0]
0
Notes
0x00
0
0
JESD204B lanes (L)
00 = 1 lane
01 = 2 lanes
11 = 4 lanes
0x00
0x8X
Read only, see
Register 0x570
JESD204B F
config
0x58D
JESD204B K
config
JESD204B M
config
0
0x58F
JESD204B
CS/N config
0x590
JESD204B N’
config
Number of control bits
(CS) per sample
00 = no control bits
(CS = 0)
01 = 1 control bit (CS =
1); Control Bit 2 only
10 = 2 control bits
(CS = 2); Control Bit 2
and 1 only
11 = 3 control bits
(CS = 3); all control bits
(2, 1, 0)
0
0
0x591
JESD204B S
config
0
0
Default
0x00
0
0x58C
0x58E
Bit 3
0
0
0
Number of octets per frame, F = Register 0x58C[7:0] + 1
0x88
Number of frames per multiframe, K = Register 0x58D[4:0] + 1.
Only values where (F × K) mod 4 = 0 are supported
Number of converters per link[7:0]
0x00 = link connected to one virtual converter (M = 1)
0x01 = link connected to two virtual converters (M = 2)
0x03 = link connected to four virtual converters (M = 4)
0x1F
0
0
Subclass
support
(Subclass V)
0=
Subclass 0
(no deterministic
latency)
1=
Subclass 1
1
Read
only,
see Reg.
0x570
See Reg.
0x570
Read
only
ADC converter resolution (N)
0x0D = 14-bit resolution
0x0F = 16-bit resolution
ADC number of bits per sample (N’)
0x7 = 8 bits
0xF = 16 bits
Samples per converter frame cycle (S)
S value = Register 0x591[4:0] + 1
Rev. 0 | Page 73 of 77
0x2F
Read
only
AD9690
Reg
Addr
(Hex)
0x592
0x5A0
0x5A1
0x5A2
0x5A3
Register
Name
JESD204B HD
and CF config
JESD204B
CHKSUM 0
JESD204B
CHKSUM 1
JESD204B
CHKSUM 2
JESD204B
CHKSUM 3
JESD204B
lane powerdown
Data Sheet
Bit 7
(MSB)
HD value
0=
disabled
1=
enabled
Bit 6
0
Bit 5
0
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0 (LSB)
Control words per frame clock cycle per link (CF)
CF value = Register 0x592, Bits[4:0]
Default
0x80
Notes
Read
only
CHKSUM value for SERDOUT0±, Bits[7:0]
0x81
CHKSUM value for SERDOUT1±, Bits[7:0]
0x82
CHKSUM value for SERDOUT2±, Bits[7:0]
0x82
CHKSUM value for SERDOUT3±, Bits[7:0]
0x84
Read
only
Read
only
Read
only
Read
only
X
SERDOUT2±
0 = on
1 = off
X
0
0x5B2
JESD204B
lane
SERDOUT0±
assign
X
SERDOUT3±
0 = on
1 = off
X
0x5B3
JESD204B
lane
SERDOUT1±
assign
X
X
X
X
0
0x5B5
JESD204B
lane
SERDOUT2±
assign
X
X
X
X
0
0x5B6
JESD204B
lane
SERDOUT3±
assign
X
X
X
X
0
0x5BF
JESD
serializer
drive adjust
0
0
0
0
0x5C1
De-emphasis
select
0
SERDOUT3±
0=
disable
1=
enable
0
SERDOUT2±
0=
disable
1=
enable
0x5B0
1
1
1
0
Rev. 0 | Page 74 of 77
SERDSERD1
OUT0±
OUT1±
0 = on
0 = on
1 = off
1 = off
SERDOUT0± lane assignment
000 = Logical Lane 0
001 = Logical Lane 1
010 = Logical Lane 2
011 = Logical Lane 3
SERDOUT1± lane assignment
000 = Logical Lane 0
001 = Logical Lane 1
010 = Logical Lane 2
011 = Logical Lane 3
SERDOUT2± lane assignment
000 = Logical Lane 0
001 = Logical Lane 1
010 = Logical Lane 2
011 = Logical Lane 3
SERDOUT3± lane assignment
000 = Logical Lane 0
001 = Logical Lane 1
010 = Logical Lane 2
011 = Logical Lane 3
Swing voltage
0000 = 237.5 mV
0001 = 250 mV
0010 = 262.5 mV
0011 = 275 mV
0100 = 287.5 mV
0101 = 300 mV
0110 = 312.5 mV
0111 = 325 mV
1000 = 337.5 mV
1001 = 350 mV
1010 = 362.5 mV
1011 = 375 mV
1100 = 387.5 mV
1101 = 400 mV
1110 = 412.5 mV
1111 = 425 mV
SERDOUT0
SERDOUT1±
0
±
0 = disable
0 = disable
1 = enable
1 = enable
0xAA
0x00
0x11
0x22
0x33
0x00
Data Sheet
Reg
Addr
(Hex)
0x5C2
AD9690
Register
Name
De-emphasis
setting for
SERDOUT0±
Bit 7
(MSB)
0
Bit 6
0
Bit 5
0
Bit 4
0
0x5C3
De-emphasis
setting for
SERDOUT1±
0
0
0
0
0x5C4
De-emphasis
setting for
SERDOUT2±
0
0
0
0
0x5C5
De-emphasis
setting for
SERDOUT3±
0
0
0
0
Bit 3
Rev. 0 | Page 75 of 77
Bit 2
Bit 1
Bit 0 (LSB)
SERDOUT0± de-emphasis settings:
0000 = 0 dB,
0001 = 0.3 dB,
0010 = 0.8 dB,
0011 = 1.4 dB,
0100 = 2.2 dB,
0101 = 3.0 dB,
0110 = 4.0 dB,
0111 = 5.0 dB
SERDOUT1± de-emphasis settings:
0000 = 0 dB,
0001 = 0.3 dB,
0010 = 0.8 dB,
0011 = 1.4 dB,
0100 = 2.2 dB,
0101 = 3.0 dB,
0110 = 4.0 dB,
0111 = 5.0 dB
SERDOUT2± de-emphasis settings:
0000 = 0 dB,
0001 = 0.3 dB,
0010 = 0.8 dB,
0011 = 1.4 dB,
0100 = 2.2 dB,
0101 = 3.0 dB,
0110 = 4.0 dB,
0111 = 5.0 dB
SERDOUT3± de-emphasis settings:
0000 = 0 dB,
0001 = 0.3 dB,
0010 = 0.8 dB,
0011 = 1.4 dB,
0100 = 2.2 dB,
0101 = 3.0 dB,
0110 = 4.0 dB,
0111 = 5.0 dB
Default
0x00
0x00
0x00
0x00
Notes
AD9690
Data Sheet
APPLICATIONS INFORMATION
POWER SUPPLY RECOMMENDATIONS
The AD9690 must be powered by the following seven supplies:
AVDD1 = 1.25 V, AVDD2 = 2.5 V, AVDD3 = 3.3 V, AVDD1_SR =
1.25 V, DVDD = 1.25 V, DRVDD = 1.25 V, and SPIVDD = 1.80 V.
For applications requiring an optimal high power efficiency and
low noise performance, it is recommended that the ADP2164
and ADP2370 switching regulators be used to convert the 3.3 V,
5.0 V, or 12 V input rails to an intermediate rail (1.8 V and 3.8 V).
These intermediate rails are then postregulated by very low
noise, low dropout (LDO) regulators (ADP1741, ADM7172,
and ADP125). Figure 114 shows the recommended power
supply scheme for AD9690.
ADP1741
1.8V
AVDD1
1.25V
plane must have several vias to achieve the lowest possible
resistive thermal path for heat dissipation to flow through the
bottom of the PCB. These vias must be solder filled or plugged.
The number of vias and the fill determine the resulting θJA
measured on the board, as shown in Table 7.
To maximize the coverage and adhesion between the ADC and
PCB, partition the continuous copper plane by overlaying a
silkscreen on the PCB into several uniform sections. This
provides several tie points between the ADC and PCB during
the reflow process, whereas using one continuous plane with no
partitions only guarantees one tie point. See Figure 115 for a
PCB layout example. For detailed information on packaging
and the PCB layout of chip scale packages, see the AN-772
Application Note, A Design and Manufacturing Guide for the
Lead Frame Chip Scale Package (LFCSP).
AVDD1_SR
1.25V
ADP1741
DVDD
1.25V
DRVDD
1.25V
3.6V
ADP125
AVDD3
3.3V
3.3V
ADM7172
OR
ADP1741
AVDD2
2.5V
12834-114
SPIVDD
(1.8V OR 3.3V)
It is not necessary to split all of these power domains in all cases.
The recommended solution shown in Figure 114 provides the
lowest noise, highest efficiency power delivery system for the
AD9690. If only one 1.25 V supply is available, route to AVDD1
first and then tap it off and isolate it with a ferrite bead or a filter
choke, preceded by decoupling capacitors for AVDD1_SR, DVDD,
and DRVDD, in that order. This is shown as the optional path
in Figure 114. The user can employ several different decoupling
capacitors to cover both high and low frequencies. These capacitors
must be located close to the point of entry at the PCB level and
close to the devices, with minimal trace lengths.
EXPOSED PAD THERMAL HEAT SLUG
RECOMMENDATIONS
The exposed pad on the underside of the ADC must be connected
to AGND to achieve the best electrical and thermal performance
of the AD9690. Connect an exposed continuous copper plane
on the PCB to the AD9690 exposed pad, Pin 0. The copper
12834-115
Figure 114. High Efficiency, Low Noise Power Solution for the AD9690
Figure 115. Recommended PCB Layout of Exposed Pad for the AD9690
AVDD1_SR (PIN 57) AND AGND (PIN 56 AND PIN 60)
AVDD1_SR (Pin 57) and AGND (Pin 56 and Pin 60) can be
used to provide a separate power supply node to the SYSREF±
circuits of AD9690. If running in Subclass 1, the AD9690 can
support periodic one-shot or gapped signals. To minimize the
coupling of this supply into the AVDD1 supply node, adequate
supply bypassing is needed.
Rev. 0 | Page 76 of 77
Data Sheet
AD9690
OUTLINE DIMENSIONS
9.10
9.00 SQ
8.90
0.30
0.25
0.18
PIN 1
INDICATOR
49
1
0.50
BSC
EXPOSED
PAD
7.70
7.60 SQ
7.50
33
0.80
0.75
0.70
0.45
0.40
0.35
16
32
17
BOTTOM VIEW
7.50 REF
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.203 REF
PKG-004396
SEATING
PLANE
0.20 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WMMD
02-12-2014-A
TOP VIEW
PIN 1
INDICATOR
64
48
Figure 116. 64-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
9 mm × 9 mm Body, Very Thin Quad
(CP-64-15)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
AD9690BCPZ-1000
AD9690BCPZ-500
AD9690BCPZRL7-1000
AD9690BCPZRL7-500
AD9690-1000EBZ
AD9690-500EBZ
1
2
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
64-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
64-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
64-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
64-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
Evaluation Board for AD9690-10002
Evaluation Board for AD9690-5002
Z = RoHS Compliant Part.
Optimized for full analog input frequency range.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D12834-0-1/15(0)
Rev. 0 | Page 77 of 77
Package Option
CP-64-15
CP-64-15
CP-64-15
CP-64-15