AD2S1210-EP Data Sheet

Variable Resolution, 10-Bit to 16-Bit R/D
Converter with Reference Oscillator
AD2S1210-EP
FEATURES
APPLICATIONS
DC and ac servo motor control
Encoder emulation
Electric power steering
Electric vehicles
Integrated starter generators/alternators
Automotive motion sensing and control
GENERAL DESCRIPTION
The AD2S1210-EP is a complete 10-bit to 16-bit resolution
tracking resolver-to-digital converter, integrating an on-board
programmable sinusoidal oscillator that provides sine wave
excitation for resolvers.
The converter accepts 3.15 V p-p ± 27% input signals, in the range
of 2 kHz to 20 kHz on the sine and cosine inputs. A Type II
servo loop is employed to track the inputs and convert the input
sine and cosine information into a digital representation of the
input angle and velocity. The maximum tracking rate is 3125 rps.
Full details about this enhanced product, including theory of
operation, registers details, and applications information, are
available in the AD2S1210 data sheet, which should be
concluded in conjunction with this data sheet.
FUNCTIONAL BLOCK DIAGRAM
REFERENCE
OSCILLATOR
(DAC)
EXCITATION
OUTPUTS
REFERENCE
PINS
CRYSTAL
VOLTAGE
REFERENCE
INTERNAL
CLOCK
GENERATOR
SYNTHETIC
REFERENCE
AD2S1210-EP
ADC
INPUTS
FROM
RESOLVER
TYPE II
TRACKING LOOP
FAULT
DETECTION
FAULT
DETECTION
OUTPUTS
ADC
POSITION
REGISTER
ENCODER
EMULATION
OUTPUTS
ENCODER
EMULATION
VELOCITY
REGISTER
CONFIGURATION
REGISTER
DATA I/O
MULTIPLEXER
DATA BUS OUTPUT
DATA I/O
RESET
09154-001
Complete monolithic resolver-to-digital converter
3125 rps maximum tracking rate (10-bit resolution)
±2.5 arc minutes of accuracy
10-/12-/14-/16-bit resolution, set by user
Parallel and serial 10-bit to 16-bit data ports
Absolute position and velocity outputs
System fault detection
Programmable fault detection thresholds
Differential inputs
Incremental encoder emulation
Programmable sinusoidal oscillator on board
Compatible with DSP and SPI interface standards
5 V supply with 2.3 V to 5 V logic interface
Support defense and aerospace applications (AQEC)
Military temperature range ( −55°C to +125°C)
Controlled manufacturing baseline
One assembly/test site
One fabrication site
Enhanced product change notification
Qualification data available upon request
Figure 1.
PRODUCT HIGHLIGHTS
1.
2.
3.
4.
5.
6.
Ratiometric tracking conversion. The Type II tracking loop
provides continuous output position data without
conversion delay. It also provides noise immunity and
tolerance of harmonic distortion on the reference and
input signals.
System fault detection. A fault detection circuit can sense
loss of resolver signals, out-of-range input signals, input
signal mismatch, or loss of position tracking. The fault
detection threshold levels can be individually programmed
by the user for optimization within a particular application.
Input signal range. The sine and cosine inputs can accept
differential input voltages of 3.15 V p-p ± 27%.
Programmable excitation frequency. Excitation frequency
is easily programmable to a number of standard frequencies
between 2 kHz and 20 kHz.
Triple format position data. Absolute 10-bit to 16-bit angular
position data is accessed via either a 16-bit parallel port or a
4-wire serial interface. Incremental encoder emulation is in
standard A-quad-B format with direction output available.
Digital velocity output. 10-bit to 16-bit signed digital
velocity accessed via either a 16-bit parallel port or a 4-wire
serial interface.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
www.analog.com
Tel: 781.329.4700
Fax: 781.461.3113
©2010 Analog Devices, Inc. All rights reserved.
AD2S1210-EP
TABLE OF CONTENTS
Features .............................................................................................. 1
Absolute Maximum Ratings ............................................................7
Applications ....................................................................................... 1
ESD Caution...................................................................................7
Functional Block Diagram .............................................................. 1
Pin Configuration and Function Descriptions..............................8
Product Highlights ........................................................................... 1
Typical Performance Characteristics ........................................... 10
Revision History ............................................................................... 2
Outline Dimensions ....................................................................... 14
Specifications..................................................................................... 3
Ordering Guide .......................................................................... 14
Timing Specifications .................................................................. 5
REVISION HISTORY
6/10—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
AD2S1210-EP
SPECIFICATIONS
AVDD = DVDD = 5.0 V ± 5%, CLKIN = 8.192 MHz ± 25%, EXC, EXC frequency = 10 kHz to 20 kHz (10-bit); 6 kHz to 20 kHz (12-bit);
3 kHz to 12 kHz (14-bit); 2 kHz to 10 kHz (16-bit); TA = TMIN to TMAX; unless otherwise noted. 1
Table 1.
Parameter
SINE, COSINE INPUTS2
Voltage Amplitude
Input Bias Current
Input Impedance
Phase Lock Range
Common-Mode Rejection
ANGULAR ACCURACY3
Angular Accuracy
Resolution
Linearity INL
10-bit
12-bit
14-bit
16-bit
Linearity DNL
Repeatability
VELOCITY OUTPUT
Velocity Accuracy4
10-bit
12-bit
14-bit
16-bit
Resolution5
DYNAMNIC PERFORMANCE
Bandwidth
10-bit
12-bit
14-bit
16-bit
Min
Typ
Max
Unit
Conditions/Comments
2.3
3.15
4.0
V p-p
8.25
µA
kΩ
Degrees
arc sec/V
Sinusoidal waveforms, differential SIN to SINLO,
COS to COSLO
VIN = 4.0 V p-p, CLKIN = 8.192 MHz
VIN = 4.0 V p-p, CLKIN = 8.192 MHz
Sine/cosine vs. EXC output, Control Register D3 = 0
10 Hz to 1 MHz, Control Register D4 = 0
arc min
Bits
No missing codes
485
−44
+44
±20
±2.5 + 1 LSB
10, 12, 14, 16
±1
±2
±4
±16
±0.9
LSB
LSB
LSB
LSB
LSB
LSB
±2
±2
±4
±16
LSB
LSB
LSB
LSB
Bits
6600
5400
2800
2200
1500
1200
350
275
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
3125
2500
1250
1000
625
500
156.25
125
rps
±1
9, 11, 13, 15
2000
2900
900
1200
400
600
100
125
Tracking Rate
10-bit
12-bit
14-bit
16-bit
Acceleration Error
10-bit
12-bit
14-bit
16-bit
±7 + 1 LSB
30
30
30
30
rps
rps
rps
arc min
arc min
arc min
arc min
Rev. 0 | Page 3 of 16
Zero acceleration
Zero acceleration
Zero acceleration
Zero acceleration
CLKIN = 8.192 MHz
CLKIN = 8.192 MHz
CLKIN = 8.192 MHz
CLKIN = 8.192 MHz
CLKIN = 10.24 MHz
CLKIN = 8.192 MHz
CLKIN = 10.24 MHz
CLKIN = 8.192 MHz
CLKIN = 10.24 MHz
CLKIN = 8.192 MHz
CLKIN = 10.24 MHz
CLKIN = 8.192 MHz
At 50,000 rps,2 CLKIN = 8.192 MHz
At 10,000 rps,2 CLKIN = 8.192 MHz
At 2500 rps,2 CLKIN = 8.192 MHz
At 125 rps,2 CLKIN = 8.192 MHz
AD2S1210-EP
Parameter
Settling Time 10° Step Input
10-bit
12-bit
14-bit
16-bit
Settling Time 179° Step Input
10-bit
12-bit
14-bit
16-bit
EXC, EXC OUTPUTS
Voltage
Min
Center Voltage
Frequency
EXC/EXC DC Mismatch
EXC/EXC AC Mismatch
THD
VOLTAGE REFERENCE
REFOUT
Drift
PSRR
CLKIN, XTALOUT6
VIL Voltage Input Low
VIH Voltage Input High
LOGIC INPUTS
VIL Voltage Input Low
VIH Voltage Input High
Typ
Max
Unit
Conditions/Comments
0.6
2.2
6.5
27.5
0.9
3.3
9.8
48
ms
ms
ms
ms
To settle to within ±2 LSB, CLKIN = 8.192 MHz
To settle to within ±2 LSB, CLKIN = 8.192 MHz
To settle to within ±2 LSB, CLKIN = 8.192 MHz
To settle to within ±2 LSB, CLKIN = 8.192 MHz
1.5
4.75
10.5
45
2.4
6.1
15.2
68
ms
ms
ms
ms
To settle to within ±2 LSB, CLKIN = 8.192 MHz
To settle to within ±2 LSB, CLKIN = 8.192 MHz
To settle to within ±2 LSB, CLKIN = 8.192 MHz
To settle to within ±2 LSB, CLKIN = 8.192 MHz
3.2
3.6
4.0
V p-p
Load ±100 µA, typical differential output
(EXC to EXC) = 7.2 V p-p
2.40
2
2.47
2.53
20
30
132
V
kHz
mV
mV
dB
−58
2.40
IOZH High Level Three-State Leakage
IOZL Low Level Three-State Leakage
POWER REQUIREMENTS
AVDD
DVDD
VDRIVE
POWER SUPPLY
IAVDD
IDVDD
IOVDD
2.53
V
ppm/°C
dB
0.8
V
V
0.8
0.7
VDRIVE = 2.7 V to 5.25 V
VDRIVE = 2.3 V to 2.7 V
VDRIVE = 2.7 V to 5.25 V
VDRIVE = 2.3 V to 2.7 V
10
V
V
V
V
µA
80
µA
RES0, RES1, RD, WR/FSYNC, A0, A1, and RESET pins
2.0
2.0
1.7
IIL Low Level Input Current (NonPull-Up)
IIL Low Level Input Current (Pull-Up)
IIH High Level Input Current
LOGIC OUTPUTS
VOL Voltage Output Low
VOH Voltage Output High
2.47
100
−60
−10
±IOUT = 100 µA
µA
0.4
10
V
V
V
µA
µA
5.25
5.25
5.25
V
V
V
12
35
2
mA
mA
mA
2.4
2.0
−10
4.75
4.75
2.3
First five harmonics
1
VDRIVE = 2.3 V to 5.25 V
VDRIVE = 2.7 V to 5.25 V
VDRIVE = 2.3 V to 2.7 V
Temperature range is as follows: –55°C to +125°C.
The voltages SIN, SINLO, COS, and COSLO, relative to AGND, must always be between 0.15 V and AVDD − 0.2 V.
All specifications within the angular accuracy parameter are tested at constant velocity, that is, zero acceleration.
4
The velocity accuracy specification includes velocity offset and dynamic ripple.
5
For example, when RES0 = 0 and RES1 = 1, the position output has a resolution of 12 bits. The velocity output has a resolution of 11 bits with the MSB indicating the
direction of rotation. In this example, with a CLKIN frequency of 8.192 MHz, the velocity LSB is 0.488 rps, that is, 1000 rps/(211).
6
The clock frequency of the AD2S1210-EP can be supplied with a crystal, an oscillator, or directly from a DSP/microprocessor digital output. When using a single-ended
clock signal directly from the DSP/microprocessor, the XTALOUT pin should remain open circuit and the logic levels outlined under the logic inputs parameter in Table 1 apply.
2
3
Rev. 0 | Page 4 of 16
AD2S1210-EP
TIMING SPECIFICATIONS
AVDD = DVDD = 5.0 V ± 5%, TA = TMIN to TMAX, unless otherwise noted.1
Table 2.
Parameter
fCLKIN
Description
Frequency of clock input
tCK
Clock period (tCK = 1/fCLKIN)
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
t12
A0 and A1 setup time before RD/CS low
Delay CS falling edge to WR/FSYNC rising edge
Address/data setup time during a write cycle
Address/data hold time during a write cycle
Delay WR/FSYNC rising edge to CS rising edge
Delay CS rising edge to CS falling edge
Delay between writing address and writing data
A0 and A1 hold time after WR/FSYNC rising edge
Delay between successive write cycles
Delay between rising edge of WR/FSYNC and falling edge of RD
Delay CS falling edge to RD falling edge
Enable delay RD low to data valid in configuration mode
VDRIVE = 4.5 V to 5.25 V
VDRIVE = 2.7 V to 3.6 V
VDRIVE = 2.3 V to 2.7 V
RD rising edge to CS rising edge
Disable delay RD high to data high-Z
Disable delay CS high to data high-Z
Delay between rising edge of RD and falling edge of WR/FSYNC
SAMPLE pulse width
Delay from SAMPLE before RD/CS low
Hold time RD before RD low
Enable delay RD/CS low to data valid
VDRIVE = 4.5 V to 5.25 V
VDRIVE = 2.7 V to 3.6 V
VDRIVE = 2.3 V to 2.7 V
RD pulse width
A0 and A1 set time to data valid when RD/CS low
VDRIVE = 4.5 V to 5.25 V
VDRIVE = 2.7 V to 3.6 V
VDRIVE = 2.3 V to 2.7 V
Delay WR/FSYNC falling edge to SCLK rising edge
Delay WR/FSYNC falling edge to SDO release from high-Z
VDRIVE = 4.5 V to 5.25 V
VDRIVE = 2.7 V to 3.6 V
VDRIVE = 2.3 V to 2.7 V
Delay SCLK rising edge to DBx valid
VDRIVE = 4.5 V to 5.25 V
VDRIVE = 2.7 V to 3.6 V
VDRIVE = 2.3 V to 2.7 V
SCLK high time
SCLK low time
SDI setup time prior to SCLK falling edge
SDI hold time after SCLK falling edge
t13
t14A
t14B
t15
t16
t17
t18
t19
t20
t21
t22
t23
t24
t25
t26
t27
t28
Rev. 0 | Page 5 of 16
Limit at TMIN, TMAX
6.144
10.24
98
163
2
22
3
2
2
10
2 × tCK + 20
2
6 × tCK + 20
2
2
Unit
MHz min
MHz max
ns min
ns max
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
37
25
30
2
16
16
2
2 × tCK + 20
6 × tCK + 20
2
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
17
21
33
6
ns min
ns min
ns min
ns min
36
37
29
3
ns min
ns min
ns min
ns min
16
26
29
ns min
ns min
ns min
24
18
32
0.4 × tSCLK
0.4 × tSCLK
3
2
ns min
ns min
ns min
ns min
ns min
ns min
ns min
AD2S1210-EP
Parameter
t29
t30
t31
t32
t33
t34
fSCLK
1
2
Description
Delay WR/FSYNC rising edge to SDO high-Z
Delay from SAMPLE before WR/FSYNC falling edge
Delay CS falling edge to WR/FSYNC falling edge in normal mode
A0 and A1 setup time before WR/FSYNC falling edge
A0 and A1 hold time after WR/FSYNC falling edge2
In normal mode, A0 = 0, A1 = 0/1
In configuration mode, A0 = 1, A1 = 1
Delay WR/FSYNC rising edge to WR/FSYNC falling edge
Frequency of SCLK input
VDRIVE = 4.5 V to 5.25 V
VDRIVE = 2.7 V to 3.6 V
VDRIVE = 2.3 V to 2.7 V
Limit at TMIN, TMAX
15
6 × tCK + 20 ns
2
2
Unit
ns min
ns min
ns min
ns min
24 × tCK + 5 ns
8 × tCK + 5 ns
10
ns min
ns min
ns min
20
25
15
MHz
MHz
MHz
Temperature range is as follows: –55°C to +125°C.
A0 and A1 should remain constant for the duration of the serial readback. This may require 24 clock periods to read back the 8-bit fault information in addition to the
16 bits of position/velocity data. If the fault information is not required, A0/A1 may be released after 16 clock cycles.
Rev. 0 | Page 6 of 16
AD2S1210-EP
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
AVDD to AGND, DGND
DVDD to AGND, DGND
VDRIVE to AGND, DGND
AVDD to DVDD
AGND to DGND
Analog Input Voltage to AGND
Digital Input Voltage to DGND
Digital Output Voltage to DGND
Analog Output Voltage Swing
Input Current to Any Pin Except Supplies 1
Operating Temperature Range (Ambient)
EP Grade
Storage Temperature Range
θJA Thermal Impedance 2
θJC Thermal Impedance2
RoHS-Compliant Temperature, Soldering
Reflow
ESD
1
2
Rating
−0.3 V to +7.0 V
−0.3 V to +7.0 V
−0.3 V to AVDD
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to AVDD + 0.3 V
±10 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
−55°C to +125°C
−65°C to +150°C
54°C/W
15°C/W
260(−5/+0)oC
2 kV HBM
Transient currents of up to 100 mA do not cause latch-up.
JEDEC 2S2P standard board.
Rev. 0 | Page 7 of 16
AD2S1210-EP
EXC
A0
AGND
EXC
SINLO
SIN
COSLO
AVDD
REFBYP
COS
RES0
REFOUT
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
48 47 46 45 44 43 42 41 40 39 38 37
RES1 1
36
PIN 1
CS 2
A1
35
DOS
RD 3
34
LOT
WR/FSYNC 4
33
RESET
DGND 5
32
DIR
31
NM
AD2S1210-EP
DVDD 6
TOP VIEW
(Not to Scale)
CLKIN 7
30
B
XTALOUT 8
29
A
SOE 9
28
DB0
27
DB1
DB15/SDO 11
26
DB2
DB14/SDI 12
25
DB3
SAMPLE 10
09154-002
DB5
DB4
DB7
DB6
DB8
DGND
DB9
VDRIVE
DB11
DB10
DB12
DB13/SCLK
13 14 15 16 17 18 19 20 21 22 23 24
Figure 2. Pin Configuration
Table 4. Pin Function Descriptions
Pin
No.
1
Mnemonic
RES1
2
3
CS
RD
4
WR/FSYNC
5, 19
DGND
6
DVDD
7
CLKIN
8
XTALOUT
9
SOE
10
SAMPLE
11
DB15/SDO
12
DB14/SDI
Description
Resolution Select 1. Logic input. RES1 in conjunction with RES0 allows the resolution of the AD2S1210-EP to be
programmed.
Chip Select. Active low logic input. The device is enabled when CS is held low.
Edge-Triggered Logic Input. When the SOE pin is high, this pin acts as a frame synchronization signal and output
enable for the parallel data outputs, DB15 to DB0. The output buffer is enabled when CS and RD are held low. When
the SOE pin is low, the RD pin should be held high.
Edge-Triggered Logic Input. When the SOE pin is high, this pin acts as a frame synchronization signal and input
enable for the parallel data inputs, DB7 to DB0. The input buffer is enabled when CS and WR/FSYNC are held low.
When the SOE pin is low, the WR/FSYNC pin acts as a frame synchronization signal and enable for the serial data bus.
Digital Ground. These pins are ground reference points for digital circuitry on the AD2S1210-EP. Refer all digital input
signals to this DGND voltage. Both of these pins can be connected to the AGND plane of a system. The DGND and
AGND voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis.
Digital Supply Voltage, 4.75 V to 5.25 V. This is the supply voltage for all digital circuitry on the AD2S1210-EP. The AVDD and
DVDD voltages should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient
basis.
Clock Input. A crystal or oscillator can be used at the CLKIN and XTALOUT pins to supply the required clock frequency of
the AD2S1210-EP. Alternatively, a single-ended clock can be applied to the CLKIN pin. The input frequency of the
AD2S1210-EP is specified from 6.144 MHz to 10.24 MHz.
Crystal Output. When using a crystal or oscillator to supply the clock frequency to the AD2S1210-EP, apply the crystal
across the CLKIN and XTALOUT pins. When using a single-ended clock source, the XTALOUT pin should be
considered a no connect pin.
Serial Output Enable. Logic input. This pin enables either the parallel or serial interface. The serial interface is selected
by holding the SOE pin low, and the parallel interface is selected by holding the SOE pin high.
Sample Result. Logic input. Data is transferred from the position and velocity integrators to the position and velocity
registers after a high-to-low transition on the SAMPLE signal. The fault register is also updated after a high-to-low
transition on the SAMPLE signal.
Data Bit 15/Serial Data Output Bus. When the SOE pin is high, this pin acts as DB15, a three-state data output pin
controlled by CS and RD. When the SOE pin is low, this pin acts as SDO, the serial data output bus controlled by CS and
WR/FSYNC. The bits are clocked out on the rising edge of SCLK.
Data Bit 14/Serial Data Input Bus. When the SOE pin is high, this pin acts as DB14, a three-state data output pin controlled
by CS and RD. When the SOE pin is low, this pin acts as SDI, the serial data input bus controlled by CS and WR/FSYNC. The
bits are clocked in on the falling edge of SCLK.
Rev. 0 | Page 8 of 16
AD2S1210-EP
Pin
No.
13
Mnemonic
DB13/SCLK
14 to
17
18
DB12 to
DB9
VDRIVE
20
21 to
28
29
DB8
DB7 to DB0
30
B
31
NM
32
DIR
33
RESET
34
35
LOT
DOS
36
37
38
A1
A0
EXC
39
EXC
40
AGND
41
42
43
SIN
SINLO
AVDD
44
45
46
47
48
COSLO
COS
REFBYP
REFOUT
RES0
A
Description
Data Bit 13/Serial Clock. In parallel mode, this pin acts as DB13, a three-state data output pin controlled by CS and RD. In
serial mode, this pin acts as the serial clock input.
Data Bit 12 to Data Bit 9. Three-state data output pins controlled by CS and RD.
Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the interface operates.
Decouple this pin to DGND. The voltage range on this pin is 2.3 V to 5.25 V and may be different from the voltage
range at AVDD and DVDD but should never exceed either by more than 0.3 V.
Data Bit 8. Three-state data output pin controlled by CS and RD.
Data Bit 7 to Data Bit 0. Three-state data input/output pins controlled by CS, RD, and WR/FSYNC.
Incremental Encoder Emulation Output A. Logic output. This output is free running and is valid if the resolver format
input signals applied to the converter are valid.
Incremental Encoder Emulation Output B. Logic output. This output is free running and is valid if the resolver format
input signals applied to the converter are valid.
North Marker Incremental Encoder Emulation Output. Logic output. This output is free running and is valid if the
resolver format input signals applied to the converter are valid.
Direction. Logic output. This output is used in conjunction with the incremental encoder emulation outputs. The DIR
output indicates the direction of the input rotation and is high for increasing angular rotation.
Reset. Logic input. The AD2S1210-EP requires an external reset signal to hold the RESET input low until VDD is within
the specified operating range of 4.75 V to 5.25 V.
Loss of Tracking. Logic output. Loss of tracking (LOT) is indicated by a logic low on the LOT pin and is not latched.
Degradation of Signal. Logic output. Degradation of signal (DOS) is detected when either resolver input (sine or cosine)
exceeds the specified DOS sine/cosine threshold or when an amplitude mismatch occurs between the sine and
cosine input voltages. DOS is indicated by a logic low on the DOS pin.
Mode Select 1. Logic input. A1 in conjunction with A0 allows the mode of the AD2S1210-EP to be selected.
Mode Select 0. Logic input. A0 in conjunction with A1 allows the mode of the AD2S1210-EP to be selected.
Excitation Frequency. Analog output. An on-board oscillator provides the sinusoidal excitation signal (EXC) and its
complement signal (EXC) to the resolver. The frequency of this reference signal is programmable via the excitation
frequency register.
Excitation Frequency Complement. Analog output. An on-board oscillator provides the sinusoidal excitation signal
(EXC) and its complement signal (EXC) to the resolver. The frequency of this reference signal is programmable via the
excitation frequency register.
Analog Ground. This pin is the ground reference points for analog circuitry on the AD2S1210-EP. Refer all analog
input signals and any external reference signal to this AGND voltage. Connect the AGND pin to the AGND plane of a
system. The AGND and DGND voltages should ideally be at the same potential and must not be more than 0.3 V
apart, even on a transient basis.
Positive Analog Input of Differential SIN/SINLO Pair. The input range is 2.3 V p-p to 4.0 V p-p.
Negative Analog Input of Differential SIN/SINLO Pair. The input range is 2.3 V p-p to 4.0 V p-p.
Analog Supply Voltage, 4.75 V to 5.25 V. This pin is the supply voltage for all analog circuitry on the AD2S1210-EP. The
AVDD and DVDD voltages ideally should be at the same potential and must not be more than 0.3 V apart, even on a
transient basis.
Negative Analog Input of Differential COS/COSLO Pair. The input range is 2.3 V p-p to 4.0 V p-p.
Positive Analog Input of Differential COS/COSLO Pair. The input range is 2.3 V p-p to 4.0 V p-p.
Reference Bypass. Connect reference decoupling capacitors at this pin. Typical recommended values are 10 µF and 0.01 µF.
Voltage Reference Output.
Resolution Select 0. Logic input. RES0 in conjunction with RES1 allows the resolution of the AD2S1210-EP to be
programmed.
Rev. 0 | Page 9 of 16
AD2S1210-EP
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, AVDD = DVDD = VDRIVE = 5 V, SIN/SINLO = 3.15 V p-p, COS/COSLO = 3.15 V p-p, CLKIN = 8.192 MHz, unless otherwise noted.
5000
9000
4500
8000
4000
7000
HITS PER CODE
HITS PER CODE
3500
6000
5000
4000
3000
2500
2000
1500
3000
1000
2000
8199
09154-003
8198
8197
8196
8195
8194
8193
8192
8191
8190
8189
8188
8186
8187
8185
8184
8183
8182
8181
CODE
CODE
Figure 3. Typical 16-Bit Angular Accuracy Histogram Of Codes,
10,000 Samples
09154-006
0
1000
8178
8179
8180
8181
8182
8183
8184
8185
8186
8187
8188
8189
8190
8191
8192
8193
8194
8195
8196
8197
8198
8199
8200
8201
500
Figure 6. Typical 12-Bit Angular Accuracy Histogram of Codes,
10,000 Samples, Hysteresis Disabled
8000
12000
7000
10000
8000
HITS PER CODE
HITS PER CODE
6000
5000
4000
3000
6000
4000
2000
CODE
0
510
09154-004
8199
8198
8197
8196
8195
8194
8193
8192
8191
8190
8189
8188
8187
8186
8185
8184
8183
8182
8181
0
Figure 4. Typical 14-Bit Angular Accuracy Histogram of Codes,
10,000 Samples, Hysteresis Disabled
511
512
CODES
513
514
09154-017
2000
1000
Figure 7. Typical 12-Bit Angular Accuracy Histogram of Codes,
10,000 Samples, Hysteresis Enabled
12000
1400
10000
1200
HITS PER CODE
6000
4000
800
600
400
2000
200
2047
2048
CODES
2049
2050
0
CODE
Figure 5. Typical 14-Bit Angular Accuracy Histogram of Codes,
10,000 Samples, Hysteresis Enabled
Figure 8. Typical 10-Bit Angular Accuracy Histogram of Codes,
10,000 Samples, Hysteresis Disabled
Rev. 0 | Page 10 of 16
09154-018
2046
8176
8177
8178
8179
8180
8181
8182
8183
8184
8185
8186
8187
8188
8189
8190
8191
8192
8193
8194
8195
8196
8197
8198
8199
8200
0
09154-005
HITS PER CODE
1000
8000
AD2S1210-EP
20
12000
18
16
14
8000
ANGLE (Degrees)
HITS PER CODE
10000
6000
4000
12
10
8
6
4
2000
128
CODES
129
130
0
0
20
18
18
16
16
14
14
ANGLE (Degrees)
20
12
10
8
4
2
2
8
12
16
20
24
TIME (ms)
28
32
36
40
0
200
14
175
ANGLE (Degrees)
225
16
12
10
8
50
2
25
0
5
6
TIME (ms)
7
8
0.75
1.00 1.25 1.50
TIME (ms)
1.75
2.00
2.25
2.50
100
75
4
0.50
125
4
3
0.25
150
6
9
10
0
09154-009
ANGLE (Degrees)
250
18
2
5.00
Figure 13. Typical 10-Bit 10° Step Response
20
1
4.50
0
Figure 10. Typical 16-Bit 10° Step Response
0
4.00
8
4
4
3.50
10
6
0
1.50 2.00 2.50 3.00
TIME (ms)
12
6
0
1.00
Figure 12. Typical 12-Bit 10° Step Response
09154-010
ANGLE (Degrees)
Figure 9. Typical 10-Bit Angular Accuracy Histogram of Codes,
10,000 Samples, Hysteresis Enabled
0.50
09154-007
127
0
Figure 11. Typical 14-Bit 10° Step Response
8
16
24
32
40
48
TIME (ms)
56
64
Figure 14. Typical 16-Bit 179° Step Response
Rev. 0 | Page 11 of 16
72
80
09154-014
126
09154-038
0
09154-008
2
20
5
18
0
–5
14
–10
MAGNITUDE (dB)
16
10
8
14-BIT
–15
–25
–30
4
–35
2
–40
0
0.25
0.50
0.75
1.00 1.25 1.50
TIME (ms)
1.75
2.00 2.25
2.50
12-BIT
–20
6
0
10-BIT
16-BIT
–45
1
Figure 15. Typical 14-Bit 179° Step Response
10
100
1k
FREQUENCY (Hz)
10k
100k
09154-015
12
09154-013
ANGLE (Degrees)
AD2S1210-EP
Figure 18. Typical System Magnitude Response
250
0
225
–20
200
–40
175
–60
150
–80
100
–120
–140
50
–160
25
–180
0
1
2
3
4
5
6
TIME (ms)
7
8
9
10
16-BIT
–200
1
10
100
1k
FREQUENCY (Hz)
10k
100k
Figure 19. Typical System Phase Response
Figure 16. Typical 12-Bit 179° Step Response
10
225
9
200
8
TRACKING ERROR (Degrees)
250
175
150
125
100
75
50
25
7
6
5
4
3
2
0
1
2
3
4
TIME (ms)
5
0
0
Figure 17. Typical 10-Bit 179° Step Response
500
1000
1500
ACCELERATION (rps2)
2000
2500
Figure 20. Typical 16-Bit Tracking Error vs. Acceleration
Rev. 0 | Page 12 of 16
09154-022
1
0
09154-011
ANGLE (Degrees)
12-BIT
–100
75
0
14-BIT
09154-016
PHASE (dB)
125
09154-012
ANGLE (Degrees)
10-BIT
10
10
9
9
8
8
TRACKING ERROR (Degrees)
7
6
5
4
3
2
1
6
5
4
3
2
0
5000 10000 15000 20000 25000 30000 35000 40000 45000
ACCELERATION (rps2)
09154-021
1
0
Figure 21. Typical 14-Bit Tracking Error vs. Acceleration
9
8
7
6
5
4
3
2
0
20000
60000
100000
ACCELERATION (rps2)
140000
180000
09154-020
1
0
0
0
200000
400000
600000
800000
ACCELERATION (rps2)
1000000
Figure 23. Typical 10-Bit Tracking Error vs. Acceleration
10
TRACKING ERROR (Degrees)
7
Figure 22. Typical 12-Bit Tracking Error vs. Acceleration
Rev. 0 | Page 13 of 16
09154-019
TRACKING ERROR (Degrees)
AD2S1210-EP
AD2S1210-EP
OUTLINE DIMENSIONS
0.75
0.60
0.45
9.20
9.00 SQ
8.80
1.60
MAX
37
48
36
1
PIN 1
0.20
0.09
7°
3.5°
0°
0.08
COPLANARITY
SEATING
PLANE
(PINS DOWN)
25
12
13
VIEW A
0.50
BSC
LEAD PITCH
VIEW A
24
0.27
0.22
0.17
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BBC
051706-A
0.15
0.05
7.20
7.00 SQ
6.80
TOP VIEW
1.45
1.40
1.35
Figure 24. 48-Lead Low Profile Quad Flat Package [LQFP]
(ST-48)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD2S1210SST-EP-RL7
Temperature Range
−55°C to +125°C
Package Description
48-Lead LQFP
Rev. 0 | Page 14 of 16
Package Option
ST-48
AD2S1210-EP
NOTES
Rev. 0 | Page 15 of 16
AD2S1210-EP
NOTES
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09154-0-6/10(0)
Rev. 0 | Page 16 of 16