PQ-17 Analog Diode Phase Shifter Data Sheet Revision Date: 12/19/2015 The most important thing we build is trust DESCRIPTION: An Analog Phase Shifter continuously changes the phase of a microwave signal by varying a DC voltage. Since the DC voltage applied to the diode is reverse bias, the current drain is negligible (typically less than 10uA). A balanced stripline configuration keeps the VSWR and amplitude ripple to a minimum for all values of phase. SPECIFICATIONS: Parameter Specification Unit of Measure 0.25 – 0.5 GHz Phase Shift 360 Degrees Insertion Loss (Max) 4.5 dB Amplitude Ripple (Max) 1.25 ±dB VSWR (Max) 2.0:1 Ratio Frequency Range (min) Outline A’ B’ C’ D’ E’ F’ G’ 10 7.75 2.50 N/A 2.30 7.25 0.75 4PLCS OUTLINE DRAWING: FEATURES: `A' • Octave bands up to 18 GHz • Fast Phase response as low as 10 nS • RF power operation 5 mW peak/CW, RF power survival 100 mW peak/CW • Bias connection using pin or connector options • Custom configurations available `E' .25 .40 BIAS PIN `H' SURFACE BIAS GND GROUND `D' RF `B' RF `F' .125 DIA THRU `G' MTG HOLES .10 .38 2 PLS `C' OUTLINE CASE STYLE PQ Revised Date: 12/19/2015 (732) 460-0212 www.cobham.com/CSCS 1 PQ-17 Analog Diode Phase Shifter NOTES: ELECTRICAL SPECIFICATION: 1. Monotonicity is Guaranteed. Control: 2. The Phase shift varies with frequency at any voltage setting. This variation, referenced to 0° at logic 0 for each frequency, is approximately ±15% for octave models, 10% for models with 25% bandwidth, and ±7.5% for models with 10% bandwidth. 3. A Connector, (SMA Female) is available in place of the bias pin at no extra charge. This will be placed at the center of the surface marked “H” on the drawing. This is the .38 x “A” surface. If a SMA Female is desired, add the suffix “C” to the model number (e.g., PQ-45C) 4. Linearization models available, call for outline and details. 0 to 10 V Typ ENVIRONMENTAL SPECIFICATIONS*: MIL-E-5400, MIL-STD-202, MIL-E-16400 Operating Temp: -40°C to +71°C Storage Temp: -65°C to +150°C Humidity: MIL-STD-202F, M103, Cond B Shock: MIL-STD-202F, M213, Cond B Altitude: MIL-STD-202F, M105, Cond B Vibration: MIL-STD-202F, M204, Cond B Thermal Shock: MIL-STD-202F, M107, Cond A * Compliant by design, verification optional MECHANICAL SPECIFICATIONS: Case Style: PQ Outline CUSTOM OPTIONS – Connectors: SMA Female per MIL-C-39012 • Gray epoxy paint per MIL-C-22750 Bias & Control Pins: ø0.02” x 0.15” long • Video transient suppression Mounting: ø0.10” through holes (4) places • Phase and amplitude tracking • Other frequency ranges available from 1 MHz to 26 GHz • Available without SMA connectors for drop-in applications • High rel screening SCREENING: Internal Visual per MIL-STD-883, Method 2017 Temperature Cycle: -65 °C to +100 °C, 10 cycles Hermetically-sealed units are fine and gross leak checked per MIL-STD-883, Method 1014. CONTACT THE FACTORY Optional High-Rel screening available upon request. Contact the factory to discuss your screening requirements. ISO 9001:2008 and AS9100 certified For further information please contact: Aeroflex Control Components, DBA Cobham Signal & Control Solutions (CSCS) reserves the right to make changes to any products and services herein at any time without notice. Consult CSCS or an authorized sales representative to verify that the information in this data sheet is current before using this product. CSCS does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by CSCS; nor does the purchase, lease, or use of a product or service from CSCS convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual rights of CSCS or of third parties. Cobham Signal & Control Solutions 40 Industrial Way East Eatontown , NJ 07724 [USA] Phone: (732) 460-0212 Fax: (732) 460-0214 [email protected] Copyright 2015, Cobham Signal & Control Solutions. All rights reserved. Revised Date: 12/19/2015 (732) 460-0212 www.cobham.com/CSCS 2