LTC3525 - 400mA Micropower Synchronous Step-Up DC/DC Converter with Output Disconnect

LTC3525-3/
LTC3525-3.3/LTC3525-5
400mA Micropower
Synchronous Step-Up DC/DC
Converter with Output Disconnect
Features
Description
Up to 95% Efficiency
Output Disconnect and Inrush Current Limit
Fixed Output Voltages of 3V, 3.3V or 5V
Delivers 65mA at 3V from a 1V Input
Delivers 60mA at 3.3V from a 1V Input,
or 140mA at 3.3V from a 1.8V Input
n Delivers 175mA at 5V from a 3V Input
n Burst Mode® Operation: I = 7µA
Q
n Only Three External Components
nV > V
IN
OUT Operation
n <1µA Shutdown Current
n Antiringing Control
n Short-Circuit and Overtemperature Protection
n Very Low Profile of 1mm
n Tiny 6-Lead SC70 Package
The LTC®3525-3/LTC3525-3.3/LTC3525-5 are high efficiency
synchronous step-up DC/DC converters with output disconnect that can start up with an input as low as 0.85V. They
offer a compact, high efficiency alternative to charge pumps
in single cell or dual cell alkaline or Li-Ion applications. Only
three small external components are required. The LTC3525
is offered in fixed output voltages of 3V, 3.3V or 5V.
n
n
n
n
n
The device includes a 0.5Ω N-channel MOSFET switch and
a 0.8Ω P-channel synchronous rectifier. Peak switch current
ranges from 150mA to 400mA, depending on load, providing
enhanced efficiency. Quiescent current is an ultralow 7µA,
maximizing battery life in portable applications.
Other features include <1µA shutdown current, antiringing control and thermal shutdown. The LTC3525 is
available in a tiny 6-Lead SC70 package.
Applications
n
n
n
n
List of LTC3525 Options
MP3 Players
Portable Instruments
Glucose Meters
Digital Cameras
L, LT, LTC, LTM, Burst Mode, Linear Technology and the Linear logo are registered trademarks
and ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners. Patents pending.
PART NAME
INPUT START-UP
VOLTAGE
OUTPUT
VOLTAGE
VOUT STATUS IN
SHUTDOWN MODE
LTC3525-3
LTC3525-3.3
0.85V
3V
Output Disconnect
0.85V
3.3V
Output Disconnect
LTC3525-5
LTC3525D-3.3
0.85V
5V
Output Disconnect
0.85V
3.3V
LTC3525L-3
0.7V
3V
Pass Through Mode
Output Disconnect
LTC3525-3.3 Efficiency and Power
Loss vs Load Current
Typical Application
L1*
10µH
100
100
90
OFF ON
1µF
SW
SHDN
VOUT
GND
GND
VOUT
3.3V
60mA
10µF
3525 TA01
*MURATA LQH32CN100K53
EFFICIENCY (%)
VIN
70
10
EFFICIENCY
60
1
POWER LOSS
50
40
0.1
VIN = 3V
VIN = 2.4V
VIN = 1.2V
30
20
0.01
POWER LOSS (mW)
80
LTC3525-3.3
VIN
1V TO 1.6V
0.1
1
10
LOAD (mA)
100
0.01
1000
LT3525 • TA02
3525fc
For more information www.linear.com/LTC3525
1
LTC3525-3/
LTC3525-3.3/LTC3525-5
Absolute Maximum Ratings
(Note 1)
Pin Configuration
VIN, VOUT Voltage......................................... – 0.3V to 6V
SW Voltage.................................................. – 0.3V to 6V
SW Voltage < 100ns..................................... –0.3V to 7V
SHDN Voltage.............................................. –0.3V to 6V
Operating Junction Temperature Range
(Notes 2, 5)............................................. –40°C to 125°C
Storage Temperature Range................... –65°C to 125°C
Lead Temperature (Soldering, 10 sec).................... 300°C
TOP VIEW
SHDN 1
6 SW
GND 2
5 GND
VIN 3
4 VOUT
SC6 PACKAGE
6-LEAD PLASTIC SC70
TJMAX = 125°C
θJA = 256°C/W IN FREE AIR, θJA = 150°C/W ON BOARD OVER GROUND PLANE
Order Information
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC3525ESC6-3#PBF
LTC3525ESC6-3#TRPBF
LCDR
6-Lead Plastic SC70
–40°C to 85°C
LTC3525ISC6-3#PBF
LTC3525ISC6-3#TRPBF
LCDR
6-Lead Plastic SC70
–40°C to 125°C
LTC3525ESC6-3.3#PBF
LTC3525ESC6-3.3#TRPBF
LBTG
6-Lead Plastic SC70
–40°C to 85°C
LTC3525ISC6-3.3#PBF
LTC3525ISC6-3.3#TRPBF
LBTG
6-Lead Plastic SC70
–40°C to 125°C
LTC3525ESC6-5#PBF
LTC3525ESC6-5#TRPBF
LBWT
6-Lead Plastic SC70
–40°C to 85°C
LTC3525ISC6-5#PBF
LTC3525ISC6-5#TRPBF
LBWT
6-Lead Plastic SC70
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
2
3525fc
For more information www.linear.com/LTC3525
LTC3525-3/
LTC3525-3.3/LTC3525-5
Electrical characteristics
(LTC3525-3)
The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at
TA = 25°C. VIN = 1.2V, VSHDN = 1.2V, VOUT = 3V unless otherwise noted. (Note 2)
PARAMETER
CONDITIONS
MIN
TYP
0.85
1
V
2.91
3.00
3.09
V
Input Start-Up Voltage
MAX
UNITS
Output Voltage
(Note 6)
Quiescent Current, VOUT
SHDN = VIN (Note 4)
7
15
µA
Quiescent Current, VIN
SHDN = VIN (Note 4)
0.5
3
µA
Quiescent Current, VIN – Shutdown
SHDN = 0V, VOUT = 0V
Not Including Switch Leakage
0.1
1
µA
NMOS Switch Leakage Current
VIN = VOUT = VSW = 5V, SHDN = 0V
0.1
1
µA
PMOS Switch Leakage Current
VIN = VSW = 5V, VOUT = 0V, SHDN = 0V
0.1
3
µA
NMOS Switch On-Resistance
(Note 3)
0.6
Ω
PMOS Switch On-Resistance
(Note 3)
0.9
Ω
A
l
Peak Current Limit
0.4
0.45
SHDN Threshold Voltage
0.4
0.6
1
V
0.01
1
µA
SHDN Input Current
VSHDN = VIN or VOUT
Electrical characteristics
(LTC3525-3.3)
The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at
TA = 25°C. VIN = 1.2V, VSHDN = 1.2V, VOUT = 3.3V unless otherwise noted. (Note 2)
PARAMETER
CONDITIONS
MIN
Input Start-Up Voltage
3.20
TYP
MAX
0.85
1
UNITS
V
3.30
3.40
V
Output Voltage
(Note 6)
Quiescent Current, VOUT
SHDN = VIN (Note 4)
7
15
µA
Quiescent Current, VIN
SHDN = VIN (Note 4)
0.5
3
µA
Quiescent Current, VIN – Shutdown
SHDN = 0V, VOUT = 0V
Not Including Switch Leakage
0.1
1
µA
NMOS Switch Leakage Current
VIN = VOUT = VSW = 5V, SHDN = 0V
0.1
1
µA
PMOS Switch Leakage Current
VIN = VSW = 5V, VOUT = 0V, SHDN = 0V
0.1
3
µA
NMOS Switch On-Resistance
(Note 3)
0.5
Ω
PMOS Switch On-Resistance
(Note 3)
0.8
Ω
0.45
A
Peak Current Limit
0.4
SHDN Threshold Voltage
SHDN Input Current
l
0.4
VSHDN = VIN or VOUT
0.6
1
V
0.01
1
µA
3525fc
For more information www.linear.com/LTC3525
3
LTC3525-3/
LTC3525-3.3/LTC3525-5
(LTC3525-5)
The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at
TA = 25°C. VIN = 2.4V, VSHDN = 2.4V, VOUT = 5V unless otherwise noted. (Note 2)
PARAMETER
CONDITIONS
MIN
Input Start-Up Voltage
4.85
TYP
MAX
0.85
1
UNITS
V
5.00
5.15
V
Output Voltage
(Note 6)
Quiescent Current, VOUT
SHDN = VIN (Note 4)
8
18
µA
Quiescent Current, VIN
SHDN = VIN (Note 4)
1.5
5
µA
Quiescent Current, VIN – Shutdown
SHDN = 0V, VOUT = 0V
Not Including Switch Leakage
0.1
1
µA
NMOS Switch Leakage Current
VIN = VOUT = VSW = 5V, SHDN = 0V
0.1
1
µA
PMOS Switch Leakage Current
VIN = VSW = 5V, VOUT = 0V, SHDN = 0V
0.1
3
µA
NMOS Switch On-Resistance
(Note 3)
0.4
Ω
PMOS Switch On-Resistance
(Note 3)
0.7
Ω
0.5
A
l
Peak Current Limit
0.4
SHDN Threshold Voltage
SHDN Input Current
0.4
VSHDN = VIN or VOUT
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC3525 is tested under pulsed load conditions such that
TJ ≈ TA. The LTC3525E is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 85°C operating
junction temperature range are assured by design, characterization and
correlation with statistical process controls. The LTC3525I is guaranteed
over the –40°C to 125°C operating junction temperature range. Note that
the maximum ambient temperature consistent with these specifications
is determined by specific operating conditions in conjunction with board
layout, the rated package thermal impedance and other environmental
4
0.6
1
V
0.01
1
µA
factors. TJ is calculated from the ambient temperature TA and power
dissipation PD according to the following formula:
TJ = TA + (PD • 150°C/W)
Note 3: Specification is guaranteed by design and not 100% tested in
production.
Note 4: Current Measurements are performed when the LTC3525 is not
switching.
Note 5: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is active.
Continuous operation above the specified maximum operating junction
temperature may impair device reliability.
Note 6: Consult LTC Marketing for other output voltage options.
3525fc
For more information www.linear.com/LTC3525
LTC3525-3/
LTC3525-3.3/LTC3525-5
Typical Performance Characteristics TA = 25°C unless otherwise noted.
Maximum Output Current vs VIN
(for VOUT to Drop 2.5%)
300
Maximum Startup Load vs VIN
(Resistive Load)
LTC3525-3.3
250
No-Load Input Current vs VIN
45
LTC3525-5
200
40
35
LOAD (mA)
LTC3525-3
LTC3525-5
150
150
LTC3525-3.3
IIN (µA)
200
IOUT (mA)
50
250
100
100
30
25
LTC3525-5
20
15
50
50
LTC3525-3
10
LTC3525-3.3
5
0
0.5
1.0
1.5
2.0
2.5 3.0
VIN (V)
4.0
3.5
0
4.5
0.5
1.5
2.0
VIN (V)
1.0
2.5
3525 G01
100
100
POWER LOSS
50
40
0.1
100
0.1
1
10
LOAD (mA)
0.01
1000
100
EFFICIENCY
70
60
POWER LOSS
40
0.1
20
0.01
0.1
1
10
LOAD (mA)
60
10
50
POWER LOSS
40
CHANGE IN VOUT (%)
1.0
COUT = 22µF
20
10
0
0.01
0.1
0
COUT = 10µF
–1.0
LTC3525-5 Load Regulation
1.5
1.5
1.0
1.0
COUT = 22µF
0
–0.5
COUT = 10µF
–1.0
0.5
–1.0
–1.5
–2.0
–2.0
20
30 40 50
LOAD (mA)
60
70
80
3525 G06
–2.5
0
20
40
60
80 100 120 140 160 180
LOAD (mA)
3525 G07
COUT = 10µF
–0.5
–2.0
10
COUT = 22µF
0
–1.5
0
VIN = 1.2V
2.0
–1.5
–2.5
1
10
LOAD (mA)
VIN = 3.6V 0.1
VIN = 2.4V
VIN = 1.2V
0.01
100
1000
3525 G05
2.5
0.5
1
30
VIN = 2.4V
2.0
1.5
–0.5
EFFICIENCY
LTC3525-3.3 Load Regulation
2.5
VIN = 1.2V
0.5
0.01
1000
100
100
70
3525 G04
LTC3525-3.3 Load Regulation
2.0
4.5
1000
80
VIN = 3V
VIN = 2.4V
VIN = 1.2V
3525 G24
2.5
1
50
30
VIN = 2.4V
VIN = 1.2V
20
0.01
10
CHANGE IN VOUT (%)
30
80
EFFICIENCY (%)
1
4.0
POWER LOSS (mW)
60
3.5
90
POWER LOSS (mW)
EFFICIENCY
70
POWER LOSS (mW)
EFFICIENCY (%)
100
90
10
2.5 3.0
VIN (V)
LTC3525-5 Efficiency and Power
Loss vs Load
EFFICIENCY (%)
90
80
2.0
3525 G03
LTC3525-3.3 Efficiency and Power
Loss vs Load
100
1.5
3525 G02
LTC3525-3 Efficiency and Power
Loss vs Load
CHANGE IN VOUT (%)
0
1.0
3.0
–2.5
0
10
20
30
40
LOAD (mA)
50
60
3525 G08
3525fc
For more information www.linear.com/LTC3525
5
LTC3525-3/
LTC3525-3.3/LTC3525-5
Typical Performance Characteristics TA = 25°C unless otherwise noted.
LTC3525-5 Load Regulation
VIN = 2.4V
2.0
1.5
1.5
1.0
1.0
0.5
COUT = 22µF
0
–0.5
–1.0
COUT = 10µF
0.5
COUT = 22µF
0
COUT = 10µF
–0.5
–1.0
900
800
700
–2.0
–2.0
400
40
60
80 100
LOAD (mA)
120
–2.5
140
0
50
100
LOAD (mA)
150
3525 G09
0.30
30
0.20
15
10
COUT = 22µF
5
0
0.1
1
LOAD (mA)
2.5 3.0
VIN (V)
3.5
4.5
100
0.10
–0.00
–0.10
–0.20
80
60
40
20
–0.40
–50
–25
0
25
50
75
TEMPERATURE (oC)
100
125
0
1.0
1.5
2.0
3525 G13
2.5 3.0
VIN (V)
3.5
4.0
4.5
3525 G14
3525 G12
LTC3525-3.3 Input Current and
VOUT at Start-Up
VIN = 1.2V
LTC3525-3.3 Output Voltage
Ripple
IOUT
5mA
IOUT
40mA
VOUT
1V/DIV
50mV/DIV
IOUT
80mA
INPUT
CURRENT
100mA/DIV
500µs/DIV
6
4.0
120
–0.30
10
2.0
Startup Delay Coming Out of
Shutdown
SWITCHING DELAY (µs)
35
CHANGE IN VOUT (%)
0.40
COUT = 10µF
1.5
3525 G11
VOUT Variation vs Temperature
(Normalized to 25°C)
40
20
300
1.0
200
3525 G10
Light Load Burst Frequency
vs Load
25
LTC3525-3.3
600
500
20
LTC3525-5
1000
–1.5
0
L = 10µH
1100
–1.5
–2.5
BURST FREQUENCY (kHz)
Switching Frequency vs VIN
1200
VIN = 3.6V
2.0
CHANGE IN VOUT (%)
CHANGE IN VOUT (%)
2.5
FREQUENCY (kHz)
LTC3525-5 Load Regulation
2.5
3525 G15
VIN = 1.2V
COUT = 10µF
50µs/DIV
3525 G16
3525fc
For more information www.linear.com/LTC3525
LTC3525-3/
LTC3525-3.3/LTC3525-5
Typical Performance Characteristics TA = 25°C unless otherwise noted.
LTC3525-3.3 Output Voltage
Ripple
LTC3525-3.3 Output Voltage
Ripple
IOUT
5mA
IOUT
5mA
IOUT
40mA
50mV/DIV
IOUT
100mA
IOUT
80mA
VIN = 1.2V
COUT = 22µF
3525 G17
50µs/DIV
VIN = 2.4V
COUT = 22µF
3525 G18
50µs/DIV
LTC3525-5 Output Voltage Ripple
LTC3525-5 Output Voltage Ripple
IOUT
20mA
IOUT
5mA
IOUT
50mA
50mV/DIV
IOUT
100mA
50mV/DIV
IOUT
200mA
IOUT
150mA
VIN = 2.4V
COUT = 22µF
50µs/DIV
3525 G19
LTC3525-3.3 50mA Load Step
Response
OUTPUT
RIPPLE
50mV/DIV
LOAD
CURRENT
20mA/DIV
LOAD
CURRENT
50mA/DIV
500µs/DIV
VIN = 3.6V
COUT = 22µF
3525 G21
3525 G20
50µs/DIV
LTC3525-3.3 100mA Load Step
Response
OUTPUT
RIPPLE
50mV/DIV
VIN = 1.2V
COUT = 22µF
50mV/DIV
IOUT
190mA
LTC3525-5 100mA Load Step
Response
OUTPUT
RIPPLE
50mV/DIV
LOAD
CURRENT
50mA/DIV
VIN = 2.4V
COUT = 22µF
500µs/DIV
3525 G22
VIN = 3.6V
COUT = 22µF
500µs/DIV
3525 G23
3525fc
For more information www.linear.com/LTC3525
7
LTC3525-3/
LTC3525-3.3/LTC3525-5
Pin Functions
SHDN (Pin 1): Logic-Controlled Shutdown Input. Connect to a voltage >1V to enable the LTC3525. Connect to
a voltage <0.4V to disable the LTC3525.
GND (Pins 2, 5): Ground.
VIN (Pin 3): Input Voltage. The LTC3525 is powered from
VIN until VOUT exceeds VIN. Once VOUT is greater than (VIN
+ 0.2V typical), it is powered from VOUT. Place a ceramic
bypass capacitor from VIN to GND. A minimum value of
1µF is recommended.
8
VOUT (Pin 4): Output Voltage Sense and the Output of the
Synchronous Rectifier. Connect the output filter capacitor
from VOUT to GND, close to the IC. A minimum value of
10µF ceramic is recommended. Use 22µF for reduced
output ripple. The output disconnect feature disconnects
VOUT from VIN when SHDN is <0.4V.
SW (Pin 6): Switch Pin. Connect an inductor from this
pin to VIN. An internal antiringing resistor is connected
across SW and VIN after the inductor current has dropped
to zero to minimize EMI.
3525fc
For more information www.linear.com/LTC3525
LTC3525-3/
LTC3525-3.3/LTC3525-5
Block Diagram
SW
VIN
6
3
VOUT
VSEL
VBEST
WELL
SWITCH
VB
4 VOUT
SHUTDOWN
SHUTDOWN GATE DRIVERS
AND
ANTI-CROSS
CONDUCTION
+
–
OFFSET
ADJUST
VREF
VREF
UVLO
+
–
IPK
UVLO
+
IPK
COMPARATOR
START-UP
LOGIC
IVAL
SHUTDOWN
ADJUST
IVALLEY
COMPARATOR
TSD
+
–
THERMAL
SHUTDOWN
–
OFFSET
+
–
SHDN 1
WAKE
INTEGRATOR
FB
VREF
SLEEP
COMPARATOR
ADJUST
5
2
GND
GND
3525 BD
3525fc
For more information www.linear.com/LTC3525
9
LTC3525-3/
LTC3525-3.3/LTC3525-5
Operation
The LTC3525 is a high performance Burst Mode operation
only, synchronous boost converter requiring only three
small external components. Its simplicity and small size
make it a high efficiency alternative to charge pump designs.
It is designed to start up from a single alkaline or nickel
cell, with input voltages as low as 1V, or from two or three
cells (or a Li-Ion battery), with voltages as high as 4.5V.
Once started, VIN can be as low as 0.5V (depending on
load current) and maintain regulation. The output voltage
is preset internally to either 3V, 3.3V or 5V. Peak switch
current is 400mA minimum, providing regulation with load
currents up to 150mA, depending on input voltage.
Synchronous rectification provides high efficiency operation while eliminating the need for an external Schottky
diode. True output disconnect eliminates inrush current
at start-up, and allows VOUT to be disconnected from VIN,
for zero shutdown current.
The output disconnect feature also allows the LTC3525 to
maintain regulation with an input voltage equal to or greater
than VOUT. Note, however, that the synchronous rectifier
is not enabled in this mode resulting in lower efficiency
and reduced output current capability.
The operating quiescent current is only 7µA typical, allowing the converter to maintain high efficiency at extremely
light loads.
Shutdown
The LTC3525 is shut down by pulling SHDN below 0.4V,
and made active by raising it above 1V. Although SHDN can
be driven above VIN or VOUT (up to the absolute maximum
rating) without damage, the LTC3525 has a proprietary test
mode that may be engaged if SHDN is held in the range
of 0.5V to 1V higher than the greater of VIN or VOUT. If
the test mode is engaged, normal PWM switching action
is interrupted, which can cause undesirable operation
in some applications. Therefore, in applications where
SHDN may be driven above VIN, a resistor divider or other
means must be employed to keep the SHDN voltage below
(VIN + 0.4V) to prevent the possibility of the test mode
being engaged. Please refer to Figure 1 for two possible
implementations.
10
LTC3525
VIN
VCNTRL
LTC3525
SHDN
SHDN
3525 F01
R
1M
VCNTRL
ZETEX ZC2811E
1M
R > (VCNTRL/(VIN + 0.4) – 1) MΩ
Figure 1
After the SHDN pin rises, there is a short delay before
switching starts. The delay is 20µs to 120µs, depending
on input voltage (see Typical Performance Characteristics
curve).
Start-Up
A start-up oscillator allows the LTC3525 to start with input
voltages as low as 1V. It remains in start-up mode until
two conditions are met. VOUT must exceed VIN by at least
0.2V typical and either VIN or VOUT must be greater than
1.8V typical.
During start-up, the synchronous rectifier is not enabled,
and the internal P-channel synchronous rectifier acts as
a follower, causing the peak voltage on SW to reach (VIN
+ 1V) typical. This limits inrush current by maintaining
control of the inductor current when VOUT is less than VIN.
To reduce power dissipation in the P-channel synchronous
rectifier when the output is shorted, a foldback feature is
incorporated that reduces the peak inductor current when
VIN is more than 1.7V greater than VOUT.
Normal Operation
Once VOUT has increased more than 0.2V typical above
VIN, and either voltage is above 1.8V, normal operation
begins, with synchronous rectification enabled. In this
mode, the internal N-channel MOSFET connected between SW and GND stays on until the inductor current
reaches a maximum peak value, after which it is turned
off and the P-channel synchronous rectifier is turned
on. It stays on, delivering current to the output, until the
inductor current has dropped below a minimum value at
3525fc
For more information www.linear.com/LTC3525
LTC3525-3/
LTC3525-3.3/LTC3525-5
Operation
which point it turns off and the cycle repeats. When the
output voltage reaches its regulated value both switches
are turned off and the LTC3525 goes to sleep, during
which time the output capacitor supplies current to the
load. Once the output voltage drops approximately 9mV
below the regulation value the IC leaves sleep mode and
switching is resumed.
The LTC3525 has been designed for low output voltage
ripple. The output voltage ripple is typically only 20mV
peak-to-peak at light load and 60mV peak-to-peak at
full load using the minimum recommended 10µF output
capacitor for the LTC3525-3.3 and a 22µF capacitor for
the LTC3525-5 (due to the capacitor’s DC bias effect). An
antiring circuit damps any oscillation at the switch node
when the inductor current falls to zero.
from 150mA to 400mA. Figure 2 shows an example of
how the inductor current changes as the load increases.
Please note that output capacitor values greater than 47µF
will result in higher peak currents than necessary at light
load. This will lower the light load efficiency.
The valley of the inductor current is automatically adjusted
as well, to maintain a relatively constant inductor ripple
current. This keeps the switching frequency relatively
constant.
The maximum average load current that can be supported
is given by:
IO(MAX ) =
0.3 • VIN • η
Amps
VO
Power Adjust Feature
where η is the efficiency (see Typical Performance Characteristics).
The LTC3525 incorporates a feature that maximizes
efficiency at light load while providing increased power
capability at heavy load by adjusting the peak and valley
of the inductor current as a function of load. Lowering the
peak inductor current to 150mA at light load optimizes
efficiency by reducing conduction losses in the internal
MOSFET switches. As the load increases, the peak inductor
current is automatically increased to a maximum of 400mA.
At intermediate loads, the peak inductor current may vary
The “burst” frequency (how often the LTC3525 delivers
a burst of current pulses to the load) is determined by
the internal hysteresis (output voltage ripple), the load
current and the amount of output capacitance. All Burst
Mode operation or hysteretic converters will enter the
audible frequency range when the load is light enough.
However, due to the low peak inductor current at light
load, circuits using the LTC3525 do not typically generate
any audible noise.
INDUCTOR
CURRENT
100mA/DIV
LOAD
CURRENT
50mA/DIV
10µs/DIV
3525 F02
Figure 2. Inductor Current Changing as a Function of Load
3525fc
For more information www.linear.com/LTC3525
11
LTC3525-3/
LTC3525-3.3/LTC3525-5
Operation
Component Selection
Inductor values between 4.7µH and 15µH are recommended. In most applications 10µH will yield the best
compromise between size and efficiency. The inductor
should be a low loss ferrite design and must be rated for
peak currents of at least 400mA without saturating. Inductors with lower DC resistance will improve efficiency. Note
that the inductor value does not have a significant effect
on ripple current, so while lower values will increase the
operating frequency, they do not reduce output voltage
ripple.
Some recommended inductor examples are Murata
LQH32C and Coilcraft LPO4812, LPO3310, DO3314,
DS1608 and MSS4020.
A ceramic input bypass capacitor should be located as
close as possible to the VIN and GND pins of the IC. A
minimum value of 1µF is recommended. If the battery is
more than a few inches away, a bulk tantalum decoupling
cap of at least 10µF is recommended on VIN.
The output capacitor should also be a ceramic, located close
to the VOUT and GND pins. A minimum value of 10µF is
recommended. Increasing the value of the output capacitor
to 22µF will result in lower output ripple. Higher capacitor
values will only offer a small reduction in output ripple,
while reducing light load efficiency by causing the peak
inductor current to increase above its minimum value of
150mA. The input and output capacitors should be X5R
or X7R types, not Y5V.
Table 1. Inductor Vendor Information
SUPPLIER
PHONE
FAX
WEBSITE
Murata
Coilcraft
USA: (814) 237-1431
USA: (814) 238-0490
www.murata.com
(847) 639-6400
(847) 639-1469
www.coilcraft.com
Sumida
USA: (847) 956-0666
USA: (847) 956-0702
www.sumida.com
Taiyo Yuden
(408) 573-4150
(408) 573-4159
www.t-yuden.com
TOKO
(847) 297-0070
(847) 699-7864
www.toko.co.jp/products/en
TDK
(847) 699-2299
(847) 803-6296
www.tdk.com
Würth
(605) 886-4385
(605) 886-4486
www.we-online.com
FAX
WEBSITE
Table 2. Capacitor Vendor Information
SUPPLIER
PHONE
Murata
USA: (814) 237-1431
USA: (814) 238-0490
www.murata.com
Taiyo Yuden
(408) 573-4150
(408) 573-4159
www.t-yuden.com
TDK
(847) 803-6100
(847) 803-6296
www.component.tdk.com
AVX
(803) 448-9411
(803) 448-1943
www.avxcorp.com
SHDN
SHDN
SW
LTC3525
VIN
GND
GND
VIN
VOUT
VOUT
3525 F03
Figure 3. Recommended Component Placement
12
3525fc
For more information www.linear.com/LTC3525
LTC3525-3/
LTC3525-3.3/LTC3525-5
Typical Applications
Single Alkaline or NiMH to 3.3V Converter with 1mm Profile
Single Cell to 3V Converter Using 1mm High Monolithic Inductor
6.8µH*
6.8µH*
1V TO 1.6V
3
1
+
2
1µF
LTC3525-3
VIN
SW
SHDN
VOUT
GND
GND
1V TO 1.6V
6
VOUT
3V
65mA
4
5
VIN
1
+
2
10µF
4V
1µF
3525 TA03
*COILCRAFT XPL2010-682ML
LTC3525-3.3
3
SHDN
VOUT
GND
GND
+
+
1
2
1µF
SW
SHDN
VOUT
GND
GND
*TOKO DFE322512C 1277AS-H-100M
5
10µF**
6.3V
3525 TA04
10µH*
LTC3525-3.3
VIN
VOUT
3.3V
60mA
4
Li-Ion to 5V
10µH*
3
6
*COILCRAFT LPO3310-682MXD
**MURATA GRM219R60J106KE191D
2-Alkaline or NiMH to 3.3V
1.8V TO 3.2V
SW
3V TO 4.2V
6
VOUT
3.3V
140mA
4
5
10µF
3525 TA05
+
3
OFF ON
1
2
Li-Ion
1µF
*TAIYO YUDEN NRH3012T100MN
LTC3525-5
VIN
SW
SHDN
VOUT
GND
GND
6
VOUT
5V
175mA
4
5
10µF
3525 TA06
3525fc
For more information www.linear.com/LTC3525
13
LTC3525-3/
LTC3525-3.3/LTC3525-5
Package Description
SC6 Package
6-Lead Plastic SC70
(Reference LTC DWG # 05-08-1638 Rev B)
0.47
MAX
0.65
REF
1.80 – 2.20
(NOTE 4)
1.00 REF
INDEX AREA
(NOTE 6)
1.80 – 2.40 1.15 – 1.35
(NOTE 4)
2.8 BSC 1.8 REF
PIN 1
RECOMMENDED SOLDER PAD LAYOUT
PER IPC CALCULATOR
0.10 – 0.40
0.65 BSC
0.15 – 0.30
6 PLCS (NOTE 3)
0.80 – 1.00
1.00 MAX
0.00 – 0.10
REF
GAUGE PLANE
0.15 BSC
0.26 – 0.46
0.10 – 0.18
(NOTE 3)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
14
SC6 SC70 1205 REV B
5. MOLD FLASH SHALL NOT EXCEED 0.254mm
6. DETAILS OF THE PIN 1 IDENTIFIER ARE OPTIONAL,
BUT MUST BE LOCATED WITHIN THE INDEX AREA
7. EIAJ PACKAGE REFERENCE IS EIAJ SC-70
8. JEDEC PACKAGE REFERENCE IS MO-203 VARIATION AB
3525fc
For more information www.linear.com/LTC3525
LTC3525-3/
LTC3525-3.3/LTC3525-5
Revision History
(Revision history begins at Rev B)
REV
DATE
DESCRIPTION
PAGE NUMBER
B
09/10
Updated “Shutdown” section
8
C
04/15
Changed input starting voltage from 1V to 0.85V
1
Added table to reference other LTC3525 family parts
1
Changed Operating Temperature Range to Operating Junction Temperature Range and changed the Operating
Junction Temperature Range from 85°C to 125°C in the Absolute Maximum Ratings section
2
Updated Order Information table
Changed Operating Temperature Range to Operating Junction Temperature Range and added Note 2 to the Electrical
Characteristics section
2
3, 4
Updated Note 2 for addition of I Grade
4
Updated VOUT Variation vs Temperature curve
6
Updated Inductor Vendor Information in Table 1
12
Updated Inductor Information
13
Updated title and inductor vendor in the Typical Application section
16
Modified Related Parts table
16
3525fc
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection
of its circuits
as described
herein will not infringe on existing patent rights.
For more
information
www.linear.com/LTC3525
15
LTC3525-3/
LTC3525-3.3/LTC3525-5
Typical Application
3.3V TO 5V Converter with 1.2mm Profile
10µH*
3
3.3V
1
2
1µF
LTC3525-5
VIN
SW
SHDN
VOUT
GND
GND
*SUMIDA 252012CDMCQDS-100MC
**MURATA GRM21BR60J226ME39L
6
VOUT
5V
200mA
4
5
22µF**
6.3V
3525 TA07
Related Parts
PART NUMBER
DESCRIPTION
COMMENTS
LTC1751-3.3/
LTC1751-5
100mA, 800kHz, Micropower, Regulated Charge Pump
DC/DC Converters
VIN: 2.5V to 5.5V, VOUT(MAX) = 3.3V/5V, IQ = 20µA,
ISD < 1µA, MS8 Package
LTC3200-5
100mA, 2MHz, Regulated 5V Charge Pump
VIN: 2.7V to 4.5V, VOUT(MAX) = 5V, IQ = 2mA,
ISD < 1µA, ThinSOT Package
LTC3400/LTC3400B
600mA (ISW), 1.2MHz, Synchronous Step-Up DC/DC Converter
92% Efficiency, VIN: 0.5V to 5V, VOUT(MAX) = 5V,
IQ = 19µA/300µA, ISD < 1µA, ThinSOT Package
LTC3401
1A (ISW), 3MHz, Synchronous Step-Up DC/DC Converter
97% Efficiency, VIN: 0.5V to 5V, VOUT(MAX) = 5.5V,
IQ = 38µA, ISD < 1µA, MS Package
LTC3402
2A (ISW), 3MHz, Synchronous Step-Up DC/DC Converter
97% Efficiency, VIN: 0.5V to 5V, VOUT(MAX) = 5.5V,
IQ = 38µA, ISD < 1µA, MS Package
LTC3421
3A (ISW), 3MHz, Synchronous Step-Up DC/DC Converter
with Output Disconnect
95% Efficiency, VIN: 0.5V to 4.5V, VOUT(MAX) = 5.25V,
IQ = 12µA, ISD < 1µA, QFN-24 Package
LTC3425
5A (ISW), 8MHz, 4-Phase Synchronous Step-Up DC/DC Converter 95% Efficiency, VIN: 0.5V to 4.5V, VOUT(MAX) = 5.25V,
with Output Disconnect
IQ = 12µA, ISD < 1µA, QFN-32 Package
LTC3429/LTC3429B
600mA, 500kHz Single/Dual Cell Micropower Synchronous
Boost Converter with Output Disconnect
95% Efficiency, VIN: 1V to 4.5V, VOUT(MAX) = 5V,
IQ = 20µA, ISD < 1µA, SC70 Package
LTC3458
1.4A (ISW), 1.5MHz, Synchronous Step-Up DC/DC Converter
with Output Disconnect
VIN: 1.5V to 6V, VOUT(MAX) = 7.5V, ISD < 1µA,
3mm × 4mm DFN Package
LTC3458L
1.7A (ISW), 1.5MHz, Synchronous Step-Up DC/DC Converter
with Output Disconnect
VIN: 1.5V to 6V, VOUT(MAX) = 6V, ISD < 1µA,
3mm × 4mm DFN Package
LTC3459
60mA, 10V Micropower Synchronous Boost Converter
95% Efficiency, VIN: 1.5V to 6V, VOUT(MAX) = 10V, IQ = 10µA, ISD
< 1µA, ThinSOT Package
LT3464
85mA (ISW), High Efficiency Step-Up DC/DC Converter
with Integrated Schottky and PNP Disconnect
VIN: 2.3V to 10V, VOUT(MAX) = 34V, IQ = 25µA,
ISD < 1µA, ThinSOT Package
LTC3528/LTC3528B
1A, 1MHz Synchronous Step-Up DC/DC Converter with Output
Disconnect
94% Efficiency, VIN Start-Up Voltage: 700mV, VOUT(MAX) = 5.25V,
IQ = 12 µA, ISD < 1µA, 2mm × 3mm DFN Package
LTC3529
1.5A, 1.5MHz, Synchronous Step-Up DC/DC Converter
95% Efficiency, VIN: 1.8V to 5.25V, VOUT(MAX) = 5.15V,
ISD < 1µA, 2mm × 3mm DFN Package
LTC3539/LTC3539-2
2A, 1MHz/2MHz Synchronous Step-Up DC/DC Converter
94% Efficiency, VIN Start-Up Voltage: 700mV, VOUT(MAX) = 5.25V,
IQ = 12µA, ISD < 1µA, 2mm × 3mm DFN Package
16
3525fc
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
For more information www.linear.com/LTC3525
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com/LTC3525
LT 0415 REV C • PRINTED IN USA
 LINEAR TECHNOLOGY CORPORATION 2005