Evaluation Board User Guide UG-058 One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com Setting Up the Evaluation Board for the ADCLK914 The ADCLK914 data sheet should be used in conjunction with this user guide. The data sheet contains full technical details about the specifications and operation of the device. PACKAGE LIST Evaluation board with component installed Applicable documents (schematic, layout, and so on) GENERAL DESCRIPTION This user guide describes how to set up and use the evaluation board for the ADCLK914. The same printed circuit board (PCB) is used to evaluate three other devices in addition to the ADCLK914 (the ADCLK905, ADCLK907, and ADCLK925). The ADCLK914 clock buffer is very fast, making it important to use adequate high bandwidth instruments to evaluate it. To that end, the evaluation board is fabricated using a high quality dielectric material between layers to maintain high signal integrity. Transmission line paths are kept as close to 50 Ω as possible. 08543-001 DIGITAL PICTURE OF THE EVALUATION BOARD Figure 1. ADCLK914/ADCLK905/ADCLK907/ADCLK925 Evaluation Board Please see the last page for an important warning and disclaimers. Rev. 0 | Page 1 of 8 UG-058 Evaluation Board User Guide TABLE OF CONTENTS Package List ....................................................................................... 1 Recommended Board Setup ........................................................3 General Description ......................................................................... 1 Clock Input Configuration ..........................................................4 Digital Picture of the Evaluation Board ......................................... 1 Evaluation Board Schematics and Artwork ...............................5 Revision History ............................................................................... 2 ESD Caution...................................................................................7 REVISION HISTORY 9/09—Revision 0: Initial Version Rev. 0 | Page 2 of 8 Evaluation Board User Guide UG-058 RECOMMENDED BOARD SETUP The recommended setup for the evaluation board is shown in Figure 2. Note that there is no output termination on the evaluation board. HVDS termination is accomplished via the 50 Ω input of the oscilloscope. In this case, VCC is set to GND and VEE is set to −3.3 V. This also meets the requirement for VCC − VEE = 3.3 V. Table 1. Basic Equipment Required Quantity 1 1 1 4 Description Single power supply Signal source High bandwidth oscilloscope Matched high speed cables POWER SUPPLY GND VCC –3.3V GND VEE OSCILLOSCOPE D Q ADCLK914 CLOCK SOURCE 50Ω EVALUATION BOARD D Q 50Ω VREF VT NOTES 1. FOR DC-COUPLED INPUTS, DISCONNECT VREF AND VT. 2. FOR AC-COUPLED INPUTS, CONNECT VREF AND VT. Figure 2. Recommended Setup for Device Evaluation Rev. 0 | Page 3 of 8 08543-002 OPTIONAL AC OR DC COUPLING UG-058 Evaluation Board User Guide CLOCK INPUT CONFIGURATION It is recommended that the clock source be ac-coupled and that VREF and VT be tied together. For single-ended operation, ac-couple the unused input to ground with a 0.1 μF capacitor. For more information about input configurations, refer to the data sheet for the ADCLK914. Figure 3 is the block diagram for the ADCLK914. 50Ω 50Ω 50Ω 50Ω Q D Q D Connection Connect to GND Connect to GND Connect to −3.3 V Connect to GND Short TP5 and TP6 for input ac coupling, else no connection Short TP5 and TP6 for input ac coupling, else no connection No connection No connection Rev. 0 | Page 4 of 8 ADCLK914 VT Table 2. Jumper Connections Jumper TP1 (GND) TP2 (VCC) TP3 (VEE) TP4 (GND) TP5 (VREF1) TP6 (VT1) TP7 (VT2) TP8 (VREF2) VCC VREF VEE Figure 3. ADCLK914 1:1 Clock/Data Buffer 08543-003 The clock inputs of the ADCLK914 on the evaluation board are dc-coupled to the SMA connectors. Therefore, the user must ac-couple the clock source, or the clock source must supply the appropriate dc common-mode voltage with adequate input swing. AP LA NE D2 J1 AP LANE A PLANE BLACK TP3 V EE ORANGE 2.2uF TP4 C24 GND D2 0.1uF C21 0.1uF C22 0.1uF C23 C27 A PLANE J10 J7 AP LA NE AP LANE CAL_2 matched lengths 0.1uF C20 0 Ohm resistors are NOT to be installed. Solder bridges will be completed by end user if desired. A PLANE 0.1uF C19 4 3 LFCSP16-3X3 ADCLK914 AP LA NE 0.01uF C45 0.01uF C44 matched length x2 D2 D2 D1 C25 2 2.2uF D1 0.1uF C18 0.1uF 0 C12 R1 C11 0 16 C10 0.1uF VREF 2 6 C26 0.1uF VEE 7 V T1 V T2 14 VEE 0.1uF C14 5 R2 C15 15 VREF 1 0.1uF C9 13 0.1uF PAD 9 Q2 VEE 10 Q2 Q1 11 12 C2 0.1uF VCC C13 8 0.1uF C1 0.1uF Q1 0.1uF D1 C16 0.1uF A PLANE AP LA NE J9 matched lengths C3 1 0.1uF J2 0.1uF C4 J8 C5 VCC C8 D1 0.1uF AP LA NE Q2 A PLA NE J3 Q2 AP LA NE J6 Q1 A PLANE A PLANE V CC TP2 RED GND BLACK AP LANE TP1 Jumpers are NOT to be installed. Solder bridges will be completed by end user if desired. V T2 A PLA NE J4 C6 J5 J12 Q1 JP1 JP4 JP3 JP2 A PLANE 0.1uF C38 A PLANE 0.1uF C41 AP LA NE 0.1uF 0.1uF 0.1uF VREF1 V REF 2 AP LA NE A PLA NE C37 V T1 V REF 2 V T2 V T1 TP5 YELLOW YELLOW TP7 TP6 TP8 C36 V REF 1 0.1uF matched length x2 C7 C39 C40 C28 C32 0.1uF 0.1uF C29 0.1uF C33 C42 C30 C34 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF C43 C31 C35 WHITE 0.1uF JP8 JP7 JP6 JP5 WHITE 0.1uF 0.1uF CAL_1 0.1uF Rev. 0 | Page 5 of 8 0.1uF Figure 4. ADCLK914 Evaluation Board Schematic V REF 1 08543-004 J11 Evaluation Board User Guide UG-058 EVALUATION BOARD SCHEMATICS AND ARTWORK C17 08543-007 Evaluation Board User Guide 08543-005 UG-058 08543-008 Figure 7. VREF and VT Plane Layers 08543-006 Figure 5. Top Trace Layer Figure 6. Ground Plane Layer Figure 8. VCC and VEE Power Plane Layer Rev. 0 | Page 6 of 8 UG-058 08543-009 08543-010 Evaluation Board User Guide Figure 9. Second Ground Plane Layer Figure 10. Bottom Trace Layer ESD CAUTION Rev. 0 | Page 7 of 8 UG-058 Evaluation Board User Guide NOTES Evaluation boards are only intended for device evaluation and not for production purposes. Evaluation boards are supplied “as is” and without warranties of any kind, express, implied, or statutory including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. No license is granted by implication or otherwise under any patents or other intellectual property by application or use of evaluation boards. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Analog Devices reserves the right to change devices or specifications at any time without notice. Trademarks and registered trademarks are the property of their respective owners. Evaluation boards are not authorized to be used in life support devices or systems. ©2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG08543-0-9/09(0) Rev. 0 | Page 8 of 8