3 4 2 1 REVISIONS REV B matched length x2 CAL_1 J11 DESCRIPTION INITIAL RELEASE VREF1 J12 DATE APPROVED 2007-08-08 NAME TP5 YELLOW 0.1uF C36 0.1uF D C9 0.1uF APLANE C37 0.1uF C38 C39 0.1uF C10 C11 APLANE 0.1uF C12 D 0.1uF APLANE 0.1uF VREF1 0 R1 APLANE J4 0.1uF C43 0.1uF C42 0.1uF VT1 Q2 PAD TP6 WHITE C 0.1uF C31 APLANE C30 C16 0.1uF 0.1uF APLANE 0.1uF VCC_13 0.1uF C41 13 VEE_14 C40 APLANE APLANE TP7 0.1uF WHITE C35 0.1uF 0.1uF C34 VT2 C32 C15 by end user if desired. 0.1uF C26 Solder bridges will be completed Q2 0.1uF C33 R2 0 Ohm resistors are NOT to be installed. J3 0 5 APLANE VEE YELLOW APLANE 0.1uF C29 VT2 APLANE Q2 9 APLANE 0.1uF C D2 VCC_8 D2 Q2 10 TP8 Q1 8 4 Q1 J6 matched lengths LFCSP16-3X3 C13 J7 D2 6 D2 11 J5 0.1uF 3 VREF2 J1 APLANE Q1 ADCLK9XX matched lengths APLANE Q1 12 C28 D1 VEE_7 2 D1 D1 7 J2 C14 D1 0.1uF 1 VREF1 J8 14 15 VT1 16 VREF2 APLANE J10 J9 matched length x2 CAL_2 APLANE APLANE B APLANE B Jumpers are NOT to be installed. Solder bridges will be completed by end user if desired. VT2 JP1 JP5 JP2 JP6 JP3 VT1 VREF2 JP7 JP4 TP3 TP4 BLACK VEE VCC ORANGE C44 RED TP1 GND 0.1uF C7 0.1uF 0.1uF C5 0.1uF C4 C3 0.1uF 0.1uF C2 C1 0.1uF C1 2.2uF PART NO DESCRIPTION HIGHEST REF DES USED 0.01uF TOLERANCES FRACTIONS +-1/32 MATERIAL APLANE REF DES UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES DECIMALS .XX +-.010 .XXX +-.005 C45 APLANE ANGLES +-2 APPROVAL DATE 7910 Triad Center Dr. GREENSBORO, NC 27409 TITLE ADCLK905/907/914/925 CUSTOMER EVALUATION BOARD CHECKED: APPROVED BY: MFG ENGINEER: DO NOT SCALE 2 ANALOG DEVICES DESIGNED BY: FINISH 3 NOTES SCHEMATIC DRAWN BY: REF DES NOT USED 4 JP8 BLACK APLANE C25 0.1uF C17 0.1uF 0.1uF C18 0.1uF C19 0.1uF C20 C21 0.1uF 0.1uF C22 C23 0.1uF C24 2.2uF C27 A TP2 0.01uF APLANE 0.1uF C6 GND VREF1 FSCM NO SIZE D DRAWING NUMBER REV 02-000000 SCALE NONE 1 SHEET C OF 1 1 A