PDF Data Sheet Rev. D

System Ready, 20-Bit, ±2LSB INL,
Voltage Output DAC
AD5790
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAM
VCC
VDD
VREFP
A1
IOVCC
6.8kΩ 6.8kΩ
R1
RFB
RFB
INV
SDIN
INPUT
SHIFT
REGISTER
AND
CONTROL
LOGIC
SCLK
SYNC
SDO
20
DAC
REG
20
20-BIT
DAC
VOUT
6kΩ
LDAC
CLR
POWER-ON-RESET
AND CLEAR LOGIC
RESET
DGND
VSS
AD5790
VREFN
AGND
10239-001
Single 20-bit voltage output DAC, ±2 LSB INL
8 nV/√Hz output noise spectral density
0.1 LSB long-term linearity error stability
±0.018 ppm/°C gain error temperature coefficient
2.5 µs output voltage settling time
3.5 nV-sec midscale glitch impulse
Integrated precision reference buffers
Operating temperature range: −40°C to +125°C
4 mm × 5 mm LFCSP package
Wide power supply range of up to ±16.5 V
35 MHz Schmitt-triggered digital interface
1.8 V compatible digital interface
Figure 1.
APPLICATIONS
Table 1. Related Devices
Medical instrumentation
Test and measurement
Industrial control
Scientific and aerospace instrumentation
Data acquisition systems
Digital gain and offset adjustment
Power supply control
Part No.
AD5791
AD5780
AD5781
AD5760
AD5541A/AD5542A
Description
20-bit, 1 LSB accurate DAC
18-bit, ±1 LSB INL, voltage output DAC ,
buffered reference inputs
18-bit, ±1 LSB INL, voltage Output DAC ,
unbuffered reference inputs
16-bit, ±0.5 LSB INL, voltage Output DAC
16-bit, 1 LSB accurate 5 V DAC
GENERAL DESCRIPTION
The AD5790 1 is a single 20-bit, unbuffered voltage-output DAC
that operates from a bipolar supply of up to 33 V. The AD5790
accepts a positive reference input in the range of 5 V to VDD −
2.5 V and a negative reference input in the range of VSS + 2.5 V
to 0 V. The AD5790 offers a relative accuracy specification of
±2 LSB maximum range, and operation is guaranteed monotonic with a −1 LSB to +3 LSB DNL specification.
The part uses a versatile 3-wire serial interface that operates at
clock rates of up to 35 MHz and is compatible with standard
SPI, QSPI™, MICROWIRE™, and DSP interface standards.
Reference buffers are also provided on chip. The part incorporates a power-on reset circuit that ensures the DAC output
powers up to 0 V in a known output impedance state and
remains in this state until a valid write to the device takes place.
The part provides a disable feature that places the output in a
defined load state. The part provides an output clamp feature
that places the output in a defined load state.
1
PRODUCT HIGHLIGHTS
1.
2.
3.
4.
5.
20-bit resolution.
Wide power supply range of up to ±16.5 V.
−40°C to +125°C operating temperature range.
Low 8 nV/√Hz noise.
Low ±0.018 ppm/°C gain error temperature coefficient.
COMPANION PRODUCTS
Output Amplifier Buffer: AD8675, ADA4898-1, ADA4004-1
External Reference: ADR445, ADR4550
DC-to-DC Design Tool: ADIsimPower™
Additional companion products on the AD5790 product page
Protected by U.S. Patent No. 7,884,747 and 8,089,380.
Rev. D
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
©2011-2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
AD5790
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
DAC Architecture....................................................................... 18
Applications ....................................................................................... 1
Serial Interface ............................................................................ 18
Functional Block Diagram .............................................................. 1
Standalone Operation ................................................................ 19
General Description ......................................................................... 1
Hardware Control Pins .............................................................. 19
Product Highlights ........................................................................... 1
On-Chip Registers ...................................................................... 19
Companion Products ....................................................................... 1
AD5790 Features ............................................................................ 23
Revision History ............................................................................... 2
Power-On to 0 V ......................................................................... 23
Specifications..................................................................................... 3
Configuring the AD5790 .......................................................... 23
Timing Characteristics ................................................................ 5
DAC Output State ...................................................................... 23
Absolute Maximum Ratings ............................................................ 7
Output Amplifier Configuration.............................................. 23
ESD Caution .................................................................................. 7
Applications Information .............................................................. 25
Pin Configuration and Function Descriptions ............................. 8
Typical Operating Circuit ......................................................... 25
Typical Performance Characteristics ............................................. 9
Evaluation Board ........................................................................ 26
Terminology .................................................................................... 17
Outline Dimensions ....................................................................... 27
Theory of Operation ...................................................................... 18
Ordering Guide .......................................................................... 27
REVISION HISTORY
7/13—Rev. C to Rev. D
Changes to t1 Test Conditions/Comments and Endnote 2 ......... 5
Deleted Figure 4 ................................................................................ 7
Changes to Pin 11 Description ....................................................... 8
Deleted Daisy-Chain Operation Section ..................................... 19
7/12—Rev. B to Rev. C
Changes to Companion Products Section and to Endnote 1 ..... 1
Changes to Terminology Section.................................................. 18
Changes to Figure 53 ...................................................................... 24
Added Figure 55.............................................................................. 26
2/12—Rev. A to Rev. B
Deleted Linearity Compensation Section ................................... 24
12/11—Rev. 0 to Rev. A
Changes to Table 1 ............................................................................ 1
Changes to Table 2 ............................................................................ 4
Changes to Figure 48 ...................................................................... 17
Changes to DAC Register Section ................................................ 21
Changes to Table 11 ........................................................................ 22
Updated Outline Dimensions ....................................................... 28
11/11—Revision 0: Initial Version
Rev. D | Page 2 of 28
Data Sheet
AD5790
SPECIFICATIONS
VDD = 12.5 V to 16.5 V, VSS = −16.5 V to −12.5 V, VREFP = 10 V, VREFN = −10 V, VCC = 2.7 V to +5.5 V, IOVCC = 1.71 V to 5.5 V,
RL = unloaded, CL = unloaded, TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter
STATIC PERFORMANCE 2
Resolution
Integral Nonlinearity Error (Relative
Accuracy)
Differential Nonlinearity Error
Long-Term Linearity Error Stability 3
Full-Scale Error
Full-Scale Error Temperature Coefficient
Zero-Scale Error
Zero-Scale Error Temperature Coefficient
Gain Error
Gain Error Temperature Coefficient
R1, RFB Matching
OUTPUT CHARACTERISTICS
Output Voltage Range
Output Voltage Settling Time
Output Noise Spectral Density
Output Voltage Noise
Midscale Glitch Impulse4
MSB Segment Glitch Impulse4
Min
20
−2
−3
−4
−1
−1
−12
−22
−40
−9
−12
−22
−19
−40
−82
−8
−13
−22
−19
−35
−68
−9
−15
−22
B Version 1
Typ
Max
±1.2
+2
±1.2
±1.2
+3
+4
+2
+3
0.1
±3.8
±2.7
±1.8
±3.8
±2.7
±1.8
±0.026
±1.3
±0.7
±0.9
±1.3
±0.7
±0.9
±0.025
±2.3
±1.9
±0.9
±2.3
±2.9
±0.9
±0.018
0.015
VREFN
+12
+22
+40
+9
+12
+22
+19
+40
+82
+8
+13
+22
+19
+35
+68
+9
+15
+22
VREFP
Unit
Test Conditions/Comments
Bits
LSB
VREFP = +10 V, VREFN = −10 V, TA = 0°C to 105°C
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
ppm/°C
LSB
LSB
LSB
LSB
LSB
LSB
ppm/°C
ppm FSR
ppm FSR
ppm FSR
ppm FSR
ppm FSR
ppm FSR
ppm/°C
%
2.5
V
µs
3.5
8
8
1.1
14
3.5
4
14
3.5
4
µs
nV/√Hz
nV/√Hz
µV p-p
nV-sec
nV-sec
nV-sec
nV-sec
nV-sec
nV-sec
Rev. D | Page 3 of 28
VREFP = +10 V, VREFN = −10 V, TA =−40°C to +105°C
VREFx = ±10 V, +10 V, and +5 V
VREFP = +10 V, VREFN = −10 V, TA = 0°C to 105°C
VREFx = ±10 V, +10 V, and +5 V
After 750 hours at TA = 135°C
VREFP = +10 V, VREFN = −10 V
VREFP = 10 V, VREFN = 0 V
VREFP = 5 V, VREFN = 0 V
VREFP = +10 V, VREFN = −10 V, TA = 0°C to 105°C
VREFP = 10 V, VREFN = 0 V, TA = 0°C to 105°C
VREFP = 5 V, VREFN = 0 V, TA = 0°C to 105°C
VREFP = +10 V, VREFN = −10 V
VREFP = +10 V, VREFN = −10 V
VREFP = 10 V, VREFN = 0 V
VREFP = 5 V, VREFN = 0 V
VREFP = +10 V, VREFN = −10 V, TA = 0°C to 105°C
VREFP = 10 V, VREFN = 0 V, TA = 0°C to 105°C
VREFP = 5 V, VREFN = 0 V, TA = 0°C to 105°C
VREFP = +10 V, VREFN = −10 V
VREFP = +10 V, VREFN = −10 V
VREFP = 10 V, VREFN = 0 V
VREFP = 5 V, VREFN = 0 V
VREFP = +10 V, VREFN = −10 V, TA = 0°C to 105°C
VREFP = 10 V, VREFN = 0 V, TA = 0°C to 105°C
VREFP = 5 V, VREFN = 0 V, TA = 0°C to 105°C
VREFP = +10 V, VREFN = −10 V
10 V step to 0.02%, using the ADA4898-1 buffer
in unity-gain mode
500 code step to ±1 LSB 4
At 1 kHz, DAC code = midscale
At 10 kHz, DAC code = midscale
DAC code = midscale, 0.1 Hz to 10 Hz bandwidth
VREFP = +10 V, VREFN = −10 V
VREFP = 10 V, VREFN = 0 V
VREFP = 5 V, VREFN = 0 V
VREFP = +10 V, VREFN = −10 V, see Figure 42
VREFP = 10 V, VREFN = 0 V, see Figure 43
VREFP = 5 V, VREFN = 0 V, see Figure 44
AD5790
Parameter
Output Enabled Glitch Impulse
Digital Feedthrough
DC Output Impedance (Normal Mode)
DC Output Impedance (Output
Clamped to Ground)
REFERENCE INPUTS
VREFP Input Range
VREFN Input Range
Input Bias Current
Input Capacitance
LOGIC INPUTS
Input Current 5
Input Low Voltage, VIL
Input High Voltage, VIH
Pin Capacitance
LOGIC OUTPUT (SDO)
Output Low Voltage, VOL
Output High Voltage, VOH
High Impedance Leakage Current
High Impedance Output Capacitance
POWER REQUIREMENTS
VDD
VSS
VCC
IOVCC
IDD
ISS
ICC
IOICC
DC Power Supply Rejection Ratio
AC Power Supply Rejection Ratio
Data Sheet
Min
5
VSS + 2.5
−20
−4
B Version 1
Typ
Max
57
0.27
3.4
6
−0.63
−0.63
1
−1
VDD − 2.5
0
+20
+4
Unit
nV-sec
nV-sec
kΩ
kΩ
V
V
nA
pF
+1
0.3 × IOVCC
µA
V
V
pF
0.4
V
V
µA
pF
0.7 × IOVCC
5
IOVCC − 0.5
±1
3
Test Conditions/Comments
On removal of output ground clamp
TA = 0°C to 105°C
VREFP, VREFN
IOVCC = 1.71 V to 5.5 V
IOVCC = 1.71 V to 5.5 V
IOVCC = 1.71 V to 5.5 V, sinking 1 mA
IOVCC = 1.71 V to 5.5 V, sourcing 1 mA
All digital inputs at DGND or IOVCC
7.5
VDD − 33
2.7
1.71
10.3
−10
600
52
±7.5
±1.5
90
90
VSS + 33
−2.5
5.5
5.5
14
−14
900
140
V
V
V
V
mA
mA
µA
µA
µV/V
µV/V
dB
dB
IOVCC ≤ VCC
SDO disabled
∆VDD ± 10%, VSS = −15 V
∆VSS ± 10%, VDD = 15 V
∆VDD ± 200 mV, 50 Hz/60 Hz, VSS = −15 V
∆VSS ± 200 mV, 50 Hz/60 Hz, VDD = 15 V
Temperature range: −40°C to +125°C, typical conditions: TA = +25°C, VDD = +15 V, VSS = −15 V, VREFP = +10 V, VREFN = −10 V.
Performance characterized with the AD8675ARZ output buffer.
3
Linearity error refers to both INL error and DNL error, either parameter can be expected to drift by the amount specified after the length of time specified.
4
The AD5790 is configured in unity-gain mode with a low-pass RC filter on the output. R = 300 Ω, C = 143 pF (total capacitance seen by the output buffer, lead
capacitance, and so forth).
5
Current flowing in an individual logic pin.
1
2
Rev. D | Page 4 of 28
Data Sheet
AD5790
TIMING CHARACTERISTICS
VCC = 2.7 V to 5.5 V; all specifications TMIN to TMAX, unless otherwise noted.
Table 3.
Parameter
t1 2
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
t12
t13
t14
t15
t16
t17
t18
t19
t20
t21
t22
1
2
Limit 1
IOVCC = 1.71 V to 3.3 V
IOVCC = 3.3 V to 5.5 V
40
28
92
60
15
10
9
5
5
5
2
2
48
40
8
6
9
7
12
7
13
10
20
16
14
11
130
130
130
130
50
50
140
140
0
0
65
60
62
45
0
0
35
35
150
150
Unit
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns min
ns typ
ns typ
ns min
ns typ
ns min
ns max
ns max
ns min
ns typ
ns typ
Test Conditions/Comments
SCLK cycle time
SCLK cycle time (readback mode)
SCLK high time
SCLK low time
SYNC to SCLK falling edge setup time
SCLK falling edge to SYNC rising edge hold time
Minimum SYNC high time
SYNC rising edge to next SCLK falling edge ignore
Data setup time
Data hold time
LDAC falling edge to SYNC falling edge
SYNC rising edge to LDAC falling edge
LDAC pulse width low
LDAC falling edge to output response time
SYNC rising edge to output response time (LDAC tied low)
CLR pulse width low
CLR pulse activation time
SYNC falling edge to first SCLK rising edge
SYNC rising edge to SDO tristate (CL = 50 pF)
SCLK rising edge to SDO valid (CL = 50 pF)
SYNC rising edge to SCLK rising edge ignore
RESET pulse width low
RESET pulse activation time
All input signals are specified with tR = tF = 1 ns/V (10% to 90% of IOVCC) and timed from a voltage level of (VIL + VIH)/2.
Maximum SCLK frequency is 35 MHz for write mode and 16 MHz for readback mode.
Rev. D | Page 5 of 28
AD5790
Data Sheet
t7
t1
SCLK
1
2
24
t3
t6
t2
t4
t5
SYNC
t9
t8
SDIN
DB23
DB0
t10
t12
t11
LDAC
t13
VOUT
t14
VOUT
t15
CLR
t16
VOUT
t21
RESET
10239-002
t22
VOUT
Figure 2. Write Mode Timing Diagram
t1
t17
SCLK
1
2
24
t3
t6
t20
t7
1
2
24
t2
t5
t4
t5
t17
SYNC
SDIN
t9
DB23
DB0
INPUT WORD SPECIFIES
REGISTER TO BE READ
NOP CONDITION
t18
t19
DB23
SDO
REGISTER CONTENTS CLOCKED OUT
Figure 3. Readback Mode Timing Diagram
Rev. D | Page 6 of 28
DB0
10239-003
t8
Data Sheet
AD5790
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Transient currents of up to 100 mA do not cause SCR latch-up.
Table 4.
Parameter
VDD to AGND
VSS to AGND
VDD to VSS
VCC to DGND
IOVCC to DGND
Digital Inputs to DGND
VOUT to AGND
VREFP to AGND
VREFN to AGND
DGND to AGND
Operating Temperature Range, TA
Industrial
Storage Temperature Range
Maximum Junction Temperature,
TJ max
Power Dissipation
LFCSP Package
θJA Thermal Impedance
Lead Temperature
Soldering
ESD (Human Body Model)
Rating
−0.3 V to +34 V
−34 V to +0.3 V
−0.3 V to +34 V
−0.3 V to +7 V
−0.3 V to VCC + 3 V or +7 V
(whichever is less)
−0.3 V to IOVCC + 0.3 V or
+7 V (whichever is less)
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
VSS − 0.3 V to + 0.3 V
−0.3 V to +0.3 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
This device is a high performance integrated circuit with an
ESD rating of <1.6 kV, and it is ESD sensitive. Proper
precautions must be taken for handling and assembly.
ESD CAUTION
−40°C to +125°C
−65°C to +150°C
150°C
(TJ max − TA)/θJA
31.0°C/W
JEDEC industry standard
J-STD-020
1.6 kV
Rev. D | Page 7 of 28
AD5790
Data Sheet
24
23
22
21
20
INV
DNC
DNC
DNC
RFB
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
AD5790
TOP VIEW
(Not to Scale)
19
18
17
16
15
14
13
AGND
VSS
VSS
VREFN
DGND
SYNC
SCLK
NOTES
1. DNC = DO NOT CONNECT. DO NOT CONNECT TO THIS PIN.
2. NEGATIVE ANALOG SUPPLY CONNECTION (VSS).
A VOLTAGE IN THE RANGE OF –16.5 V TO –2.5 V
CAN BE CONNECTED. VSS SHOULD BE DECOUPLED
TO AGND. THE PADDLE CAN BE LEFT ELECTRICALLY
UNCONNECTED PROVIDED THAT A SUPPLY
CONNECTION IS MADE AT THE VSS PINS. IT IS
RECOMMENDED THAT THE PADDLE BE THERMALLY
CONNECTED TO A COPPER PLANE FOR ENHANCED
THERMAL PERFORMANCE.
10239-005
VCC 8
IOVCC 9
DNC 10
SDO 11
SDIN 12
VOUT 1
VREFP 2
VDD 3
RESET 4
VDD 5
CLR 6
LDAC 7
Figure 4. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2
3, 5
Mnemonic
VOUT
VREFP
VDD
4
6
RESET
CLR
7
LDAC
8
9
VCC
IOVCC
10, 21, 22, 23
11
12
DNC
SDO
SDIN
13
SCLK
14
SYNC
15
16
17, 18
DGND
VREFN
VSS
19
20
24
EPAD
AGND
RFB
INV
VSS
Description
Analog Output Voltage.
Positive Reference Voltage Input. A voltage in the range of 5 V to VDD − 2.5 V can be connected.
Positive Analog Supply Connection. A voltage in the range of 7.5 V to 16.5 V can be connected. VDD must be
decoupled to AGND.
Active Low Reset. Asserting this pin returns the AD5790 to its power-on status.
Active Low Input. Asserting this pin sets the DAC register to a user defined value (see Table 12) and updates the
DAC output. The output value depends on the DAC register coding that is being used, either binary or twos
complement.
Active Low Load DAC Logic Input. This is used to update the DAC register and, consequently, the analog output.
When tied permanently low, the output is updated on the rising edge of SYNC. If LDAC is held high during the
write cycle, the input register is updated, but the output update is held off until the falling edge of LDAC. The
LDAC pin should not be left unconnected.
Digital Supply. Voltage range is from 2.7 V to 5.5 V. VCC should be decoupled to DGND.
Digital Interface Supply. Digital threshold levels are referenced to the voltage applied to this pin. Voltage range is
from 1.71 V to 5.5 V
Do Not Connect. Do not connect to these pins.
Serial Data Output. Data is clocked out on the rising edge of the serial clock input.
Serial Data Input. This device has a 24-bit input shift register. Data is clocked into the register on the falling edge
of the serial clock input.
Serial Clock Input. Data is clocked into the input shift register on the falling edge of the serial clock input. Data
can be transferred at rates of up to 35 MHz.
Level-Triggered Control Input (Active Low). This is the frame synchronization signal for the input data. When
SYNC goes low, it enables the input shift register, and data is then transferred in on the falling edges of the
following clocks. The DAC is updated on the rising edge of SYNC.
Ground Reference Pin for Digital Circuitry.
Negative Reference Voltage Input.
Negative Analog Supply Connection. A voltage in the range of −16.5 V to −2.5 V can be connected. VSS must be
decoupled to AGND.
Ground Reference Pin for Analog Circuitry.
Feedback Connection for External Amplifier. See the AD5790 Features section for further details.
Inverting Input Connection for External Amplifier. See the AD5790 Features section for further details.
Negative Analog Supply Connection (VSS). A voltage in the range of −16.5 V to −2.5 V can be connected. VSS must
be decoupled to AGND. The paddle can be left electrically unconnected provided that a supply connection is
made at the VSS pins. It is recommended that the paddle be thermally connected to a copper plane for enhanced
thermal performance.
Rev. D | Page 8 of 28
Data Sheet
AD5790
TYPICAL PERFORMANCE CHARACTERISTICS
AD8675 OUTPUT BUFFER
TA = 25°C
1.25
2.0
AD8675 OUTPUT BUFFER
TA = 25°C
1.5
0.75
1.0
INL (LSB)
INL (LSB)
0.5
0.25
–0.25
0
–0.5
–1.0
–0.75
–1.5
0
200000
400000
600000
800000
DAC CODE
1000000
–3.0
1200000
Figure 5. Integral Nonlinearity Error vs. DAC Code, ±10 V Span
2.5
0
200000
400000
600000
800000
1000000
1200000
DAC CODE
Figure 8. Integral Nonlinearity Error vs. DAC Code, 5 V Span, ×2 Gain Mode
2.0
AD8675 OUTPUT BUFFER
TA = 25°C
2.0
VREFP = +5V
VREFN = 0V
VDD = +15V
VSS = –15V
–2.5
10239-009
–1.75
–2.0
10239-006
–1.25
VREFP = +10V
VREFN = –10V
VDD = +15V
VSS = –15V
AD8675 OUTPUT BUFFER
TA = 25°C
1.5
1.5
1.0
DNL (LSB)
INL (LSB)
1.0
0.5
0
0.5
0
–0.5
–0.5
–1.0
0
200000
400000
800000
600000
DAC CODE
1000000
1200000
–1.5
10239-007
–2.0
VREFP = +10V
VREFN = –10V
VDD = +15V
VSS = –15V
–1.0
0
200000
400000
600000
800000
1000000
1200000
DAC CODE
10239-010
VREFP = +10V
VREFN = 0V
VDD = +15V
VSS = –15V
–1.5
Figure 9. Differential Nonlinearity Error vs. DAC Code, ±10 V Span
Figure 6. Integral Nonlinearity Error vs. DAC Code, 10 V Span
2.0
2.0
AD8675 OUTPUT BUFFER
TA = 25°C
AD8675 OUTPUT BUFFER
TA = 25°C
1.5
1.5
1.0
1.0
DNL (LSB)
0
–0.5
–1.0
0.5
0
–0.5
–2.0
VREFP = +5V
VREFN = 0V
VDD = +15V
VSS = –15V
–2.5
–3.0
0
200000
400000
600000
800000
1000000
1200000
DAC CODE
VREFP = +10V
VREFN = 0V
VDD = +15V
VSS = –15V
–1.0
–1.5
0
200000
400000
600000
800000
1000000
1200000
DAC CODE
Figure 10. Differential Nonlinearity Error vs. DAC Code, 10 V Span
Figure 7. Integral Nonlinearity Error vs. DAC Code, 5 V Span
Rev. D | Page 9 of 28
10239-011
–1.5
10239-008
INL (LSB)
0.5
AD5790
3.0
Data Sheet
AD8675 OUTPUT BUFFER
TA = 25°C
2.5
1.4
DNL ERROR (LSB)
1.0
0.5
0
1.0
0.8
0.6
0.4
VDD = +15V
VSS = –15V
AD8675 OUTPUT BUFFER
0.2
–0.5
0
400000
600000
800000
1000000
–0.2
–40
10239-012
200000
0
1200000
DAC CODE
–20
0
20
40
60
80
100
TEMPERATURE (°C)
10239-015
DNL (LSB)
1.5
Figure 14. Differential Nonlinearity Error vs. Temperature
Figure 11. Differential Nonlinearity Error vs. DAC Code, 5 V Span
1.5
2.5
AD8675 OUTPUT BUFFER
TA = 25°C
VREFP = +5V
VREFN = 0V
VDD = +15V
VSS = –15V
2.0
INL MAX
1.0
INL ERROR (LSB)
1.5
DNL (LSB)
±10V SPAN MIN DNL
+10V SPAN MIN DNL
+5V SPAN MIN DNL
1.2
2.0
–1.0
±10V SPAN MAX DNL
+10V SPAN MAX DNL
+5V SPAN MAX DNL
1.6
VREFP = +5V
VREFN = 0V
VDD = +15V
VSS = –15V
1.0
0.5
0.5
0
TA = 25°C
VREFP = +10V
VREFN = –10V
AD8675 OUTPUT BUFFER
–0.5
0
–1.0
0
200000
400000
600000
800000
1000000
–1.5
12.5
10239-013
1200000
DAC CODE
Figure 12. Differential Nonlinearity Error vs. DAC Code, 5 V Span, ×2 Gain
Mode
±10V SPAN MAX INL
+10V SPAN MAX INL
+5V SPAN MAX INL
2.0
14.0
14.5
15.0
15.5
16.0
16.5
VDD/|VSS| (V)
Figure 15. Integral Nonlinearity Error vs. Supply Voltage, ±10 V Span
±10V SPAN MIN INL
+10V SPAN MIN INL
+5V SPAN MIN INL
INL MAX
1.3
0.8
INL ERROR (LSB)
1.5
1.0
0.5
VDD = +15V
VSS = –15V
AD8675 OUTPUT BUFFER
0.3 TA = 25°C
VREFP = 5V
VREFN = 0V
–0.2 AD8675 OUTPUT BUFFER
–0.7
–0.5
–1.2
–1.0
–1.7
–1.5
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
100
10239-014
INL ERROR (LSB)
13.5
1.8
2.5
0
13.0
–2.2
7.5
INL MIN
8.5
9.5
10.5
11.5
12.5
13.5
14.5
15.5
16.5
VDD/|VSS| (V)
Figure 16. Integral Nonlinearity Error vs. Supply Voltage, 5 V Span
Figure 13. Integral Nonlinearity Error vs. Temperature
Rev. D | Page 10 of 28
10239-017
–1.0
10239-016
INL MIN
–0.5
Data Sheet
AD5790
1.4
11
TA = 25°C
VREFP = 5V
9 VREFN = 0V
AD8675 OUTPUT BUFFER
DNL MAX
ZERO-SCALE ERROR (LSB)
DNL ERROR (LSB)
1.0
0.8
0.6
TA = 25°C
VREFP = +10V
VREFN = –10V
AD8675 OUTPUT BUFFER
0.4
0.2
DNL MIN
–0.2
12.5
13.0
13.5
14.0
14.5
15.0
5
3
1
–1
–3
15.5
16.0
16.5
VDD/|VSS| (V)
–5
7.5
10239-018
0
7
8.5
9.5
11.5
10.5
12.5
Figure 17. Differential Nonlinearity Error vs. Supply Voltage, ±10 V Span
1.2
–0.4
1.0
–0.6
MIDSCALE ERROR (LSB)
DNL ERROR (LSB)
15.5
16.5
–0.2
TA = 25°C
VREFP = +10V
VREFN = –10V
AD8675 OUTPUT BUFFER
DNL MAX
0.8
0.4
14.5
Figure 20. Zero-Scale Error vs. Supply Voltage, 5 V Span
1.4
0.6
13.5
VDD/|VSS| (V)
10239-021
1.2
TA = 25°C
VREFP = 5V
VREFN = 0V
AD8675 OUTPUT BUFFER
0.2
–0.8
–1.0
–1.2
–1.4
–1.6
DNL MIN
0
9.5
10.5
11.5
12.5
13.5
14.5
15.5
16.5
VDD/|VSS| (V)
–2.0
12.5
13.5
14.0
14.5
10
6
MIDSCALE ERROR (LSB)
–0.5
–1.0
16.0
16.5
TA = 25°C
VREFP = 5V
VREFN = 0V
AD8675 OUTPUT BUFFER
8
0
15.5
Figure 21. Midscale Error vs. Supply Voltage, ±10 V Span
TA = 25°C
VREFP = +10V
1.0 VREFN = –10V
AD8675 OUTPUT BUFFER
0.5
15.0
VDD/|VSS| (V)
Figure 18. Differential Nonlinearity Error vs. Supply Voltage, 5 V Span
4
2
0
–2
–4
–6
–1.5
13.0
13.5
14.0
14.5
15.0
15.5
16.0
16.5
VDD/|VSS| (V)
Figure 19. Zero-Scale Error vs. Supply Voltage, ±10 V Span
–10
7.5
8.5
9.5
10.5
11.5
12.5
13.5
14.5
15.5
VDD/|VSS| (V)
Figure 22. Midscale Error vs. Supply Voltage, 5 V Span
Rev. D | Page 11 of 28
16.5
10239-023
–8
–2.0
12.5
10239-020
ZERO-SCALE ERROR (LSB)
13.0
10239-022
8.5
10239-019
–0.2
7.5
–1.8
AD5790
Data Sheet
2.0
6.0
5.8
5.6
1.4
GAIN ERROR (LSB)
1.2
1.0
0.8
0.6
0.4
5.4
5.2
5.0
4.8
4.6
4.4
TA = 25°C
V
= 5V
4.2 VREFP = 0V
REFN
AD8675 OUTPUT BUFFER
4.0
7.5
8.5
9.5
10.5 11.5
0
12.5
13.0
13.5
14.0
14.5
15.0
15.5
16.0
16.5
VDD/|VSS| (V)
10239-024
0.2
13.5
14.5
15.5
16.5
Figure 26. Gain Error vs. Supply Voltage, 5 V Span
Figure 23. Full-Scale Error vs. Supply Voltage, ±10 V Span
1.25
8
TA = 25°C
V
= 5V
6 VREFP = 0V
REFN
AD8675 OUTPUT BUFFER
4
INL MAX
0.75
2
0.25 T = 25°C
A
VDD = +15V
VSS = –15V
AD8675 OUTPUT BUFFER
–0.25
INL ERROR (LSB)
FULL-SCALE ERROR (LSB)
12.5
VDD/|VSS| (V)
10239-027
FULL-SCALE ERROR (LSB)
TA = 25°C
V
= +10V
1.8 VREFP = –10V
REFN
AD8675 OUTPUT BUFFER
1.6
0
–2
–4
–0.75
–6
INL MIN
–8
–1.25
8.5
9.5
10.5
11.5
12.5
13.5
14.5
15.5
16.5
VDD/|VSS| (V)
–1.75
5.0
10239-025
–12
7.5
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
Figure 27. Integral Nonlinearity Error vs. Reference Voltage
1.15
TA = 25°C
VREFP = +10V
VREFN = –10V
AD8675 OUTPUT BUFFER
INL MAX
DNL ERROR (LSB)
0.95
0.5
0
0.75
0.55 TA = 25°C
VDD = +15V
VSS = –15V
AD8675
OUTPUT BUFFER
0.35
0.15
INL MIN
–0.5
–1.0
12.5
13.0
13.5
14.0
14.5
15.0
15.5
16.0
VDD/|VSS| (V)
16.5
Figure 25. Gain Error vs. Supply Voltage, ±10 V Span
–0.25
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
VREFP /|VREFN | (V)
Figure 28. Differential Nonlinearity Error vs. Reference Voltage
Rev. D | Page 12 of 28
10239-029
–0.05
10239-026
GAIN ERROR (LSB)
1.0
6.0
VREFP /|VREFN | (V)
Figure 24. Full-Scale Error vs. Supply Voltage, 5 V Span
1.5
5.5
10239-028
–10
Data Sheet
AD5790
–4.0
–4.5
–0.7
–0.9
–5.0
–5.5
–6.0
–1.1
–6.5
–1.3
–7.0
–1.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
VREFP /|VREFN | (V)
TA = 25°C
VDD = +15V
VSS = –15V
AD8675 OUTPUT BUFFER
–7.5
5.0
7.0
7.5
8.5
8.0
9.0
9.5
10.0
Figure 32. Gain Error vs. Reference Voltage
7.0
TA = 25°C
VREFP = +15V
VREFN = –15V
AD8675 OUTPUT BUFFER
6.5
FULL-SCALE ERROR (LSB)
MIDSCALE ERROR (LSB)
–1.5
6.5
VREFP /|VREFN | (V)
Figure 29. Zero-Scale Error vs. Reference Voltage
–1.0
6.0
5.5
10239-033
GAIN ERROR (LSB)
–0.5
10239-030
ZERO-SCALE ERROR (LSB)
TA = 25°C
–0.1 V = +15V
DD
VSS = –15V
AD8675 OUTPUT BUFFER
–0.3
–2.0
–2.5
VDD = +15V
VSS = –15V
AD8675 OUTPUT BUFFER
6.0
5.5
5.0
4.5
4.0
–3.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
VREFP /|VREFN | (V)
3.0
–40
10239-031
–3.5
5.0
20
40
60
80
100
Figure 33. Full-Scale Error vs. Temperature
6.5
3
VDD = +15V
VSS = –15V
AD8675
OUTPUT BUFFER
2
TA = 25°C
VDD = +15V
VSS = –15V
AD8675 OUTPUT BUFFER
MIDSCALE ERROR (LSB)
5.5
5.0
4.5
±10V SPAN
+10V SPAN
+5V SPAN
1
0
–1
–2
–3
4.0
3.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
VREFP /|VREFN | (V)
10.0
Figure 31. Full-Scale Error vs. Reference Voltage
–5
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
Figure 34. Midscale Error vs. Temperature
Rev. D | Page 13 of 28
100
10239-035
–4
10239-032
FULL-SCALE ERROR (LSB)
0
TEMPERATURE (°C)
Figure 30. Midscale Error vs. Reference Voltage
6.0
–20
10239-034
±10V SPAN
+10V SPAN
+5V SPAN
3.5
AD5790
Data Sheet
0.010
5
±10V SPAN
+10V SPAN
+5V SPAN
0.008
IDD
0.006
1
0.004
–1
IDD/ISS (mA)
–3
–5
0.002
0
–0.002
–0.004
–7
–0.006
–9
20
40
80
60
100
TEMPERATURE (°C)
–0.010
–20
VDD = +15V
VSS = –15V
AD8675 OUTPUT BUFFER
–6
0
VOUT (V)
2
–8
–4
–12
–6
–14
–8
0
20
40
60
80
100
TEMPERATURE (°C)
–10
–1
TA = 25°C
800
700
20
0
1
2
3
4
5
4
5
Figure 39. Rising Full-Scale Voltage Step
6
IOVCC = 5V, LOGIC VOLTAGE
INCREASING
IOVCC = 5V, LOGIC VOLTAGE
DECREASING
IOVCC = 3V, LOGIC VOLTAGE
INCREASING
IOVCC = 3V, LOGIC VOLTAGE
DECREASING
4
2
0
VOUT (V)
600
15
TIME (µs)
Figure 36. Gain Error vs. Temperature
900
10
–2
–10
–20
0
5
VDD/VSS (V)
4
–4
–16
–40
–5
6
±10V SPAN
+10V SPAN
+5V SPAN
10239-037
GAIN ERROR (LSB)
–2
–10
Figure 38. Power Supply Currents vs. Power Supply Voltages
Figure 35. Zero-Scale Error vs. Temperature
0
–15
10239-039
0
10239-040
–20
10239-036
–11
–40
500
400
–2
–4
300
–6
200
–8
100
0
0
1
2
3
4
LOGIC INPUT VOLTAGE (V)
5
6
10239-038
IOICC (µA)
ISS
–0.008
–10
–1
0
1
2
3
TIME (µs)
Figure 40. Falling Full-Scale Voltage Step
Figure 37. IOICC vs. Logic Input Voltage
Rev. D | Page 14 of 28
10239-041
ZERO-SCALE ERROR (LSB)
VDD = +15V
VSS = –15V
3 AD8675 OUTPUT BUFFER
Data Sheet
AD5790
6
10
9
5
OUTPUT GLITCH (nV-sec)
8
6
5
4
3
VREFP = +10V
VREFN = –10V
RC LOW-PASS FILTER
UNITY GAIN MODE
ADA4898-1
0
–1
0
1
2
3
4
4
3
2
1
5
TIME (µs)
0
CODE
Figure 41. 500 Code Step Settling Time
Figure 44. 6 MSB Segment Glitch Energy for 5 V VREF
55
NEGATIVE
POSITIVE
VREFP = +10V
VREFN = –10V
UNITY GAIN MODE
ADA4898-1
20 RC LOW-PASS FILTER
±10V SPAN
+10V SPAN
+5V SPAN
45
POSITIVE CODE
CHANGE
NEGATIVE CODE
CHANGE
VREFP = +10V
VREFN = –10V
RC LOW-PASS FILTER
UNITY GAIN MODE
ADA4898-1
35
OUTPUT GLITCH (mV)
OUTPUT GLITCH (nV-sec)
25
10239-045
1
10239-042
2
NEGATIVE
POSITIVE
16384
65536
114688
163840
212992
262144
311296
360448
409600
458752
507904
557056
606208
655360
704512
753664
802816
851968
901120
950272
999424
VOUT (mV)
7
VREFP = 5V
VREFN = 0V
UNITY GAIN MODE
ADA4898-1
RC LOW-PASS FILTER
15
10
25
15
5
–5
5
–25
CODE
1
3
2
TIME (µs)
Figure 42. 6 MSB Segment Glitch Energy for ±10 V VREF
Figure 45. Midscale Peak-to-Peak Glitch for ±10 V
800
4.0
OUTPUT VOLTAGE (nV)
VREFP = 10V
VREFN = 0V
UNITY
GAIN MODE
3.5
ADA4898-1
RC LOW-PASS FILTER
3.0
NEGATIVE
POSITIVE
2.5
2.0
1.5
TA = 25°C
VDD = +15V
600 VSS = –15V
VREFP = +10V
VREFN = –10V
400
MIDSCALE CODE LOADED
OUTPUT UNBUFFERED
AD8676 REFERENCE BUFFERS
200
0
–200
1.0
–600
0
10239-044
CODE
0
Figure 43. 6 MSB Segment Glitch Energy for 10 V VREF
1
2
3
4
5
6
TIME (Seconds)
7
8
9
10
Figure 46. Voltage Output Noise, 0.1 Hz to 10 Hz Bandwidth
Rev. D | Page 15 of 28
10239-047
–400
0.5
16384
65536
114688
163840
212992
262144
311296
360448
409600
458752
507904
557056
606208
655360
704512
753664
802816
851968
901120
950272
999424
OUTPUT GLITCH (nV-sec)
0
1
10239-043
16384
49152
81920
114688
147456
180224
212992
245760
278528
311296
344064
376832
409600
442368
475136
507904
540672
573440
606208
638976
671744
704512
737280
770048
802816
835584
868352
901120
933888
966656
999424
1032192
0
10239-047
–15
AD5790
Data Sheet
200
VDD = +15V
VSS = –15V
VREFP = +10V
VREFN = –10V
VDD = +15V
VSS = –15V
VREFP = +10V
VREFN = –10V
UNITY GAIN
ADA4898-1
180
OUTPUT VOLTAGE (mV)
160
10
140
120
100
80
60
40
20
1
10
100
1k
FREQUENCY (Hz)
10k
Figure 47. Noise Spectral Density vs. Frequency
–20
0
1
2
3
4
5
TIME (µs)
Figure 48. Glitch Impulse on Removal of Output Clamp
Rev. D | Page 16 of 28
6
10239-048
0
1
0.1
10239-056
NSD (nV/√Hz)
100
Data Sheet
AD5790
TERMINOLOGY
Relative Accuracy
Relative accuracy, or integral nonlinearity (INL), is a measure of
the maximum deviation, in LSB, from a straight line passing
through the endpoints of the DAC transfer function. A typical
INL error vs. code plot is shown in Figure 5.
Differential Nonlinearity (DNL)
Differential nonlinearity is the difference between the measured
change and the ideal 1 LSB change between any two adjacent
codes. A specified differential nonlinearity of ±1 LSB maximum
ensures monotonicity. This DAC is guaranteed monotonic. A
typical DNL error vs. code plot is shown in Figure 9.
Long-Term Linearity Error Stability
Linearity error long-term stability is a measure of the stability of
the linearity of the DAC over a long period of time. It is specified in LSB for a time period of 500 hours and 1000 hours at an
elevated ambient temperature.
Zero-Scale Error
Zero-scale error is a measure of the output error when zero-scale
code (0x00000) is loaded to the DAC register. Ideally, the output
voltage should be VREFN. Zero-scale error is expressed in LSBs.
Zero-Scale Error Temperature Coefficient
Zero-scale error temperature coefficient is a measure of the
change in zero-scale error with a change in temperature. It is
expressed in ppm FSR/°C.
Full-Scale Error
Full-scale error is a measure of the output error when full-scale
code (0xFFFFF) is loaded to the DAC register. Ideally, the
output voltage should be VREFP − 1 LSB. Full-scale error is
expressed in LSBs.
Full-Scale Error Temperature Coefficient
Full-scale error temperature coefficient is a measure of the
change in full-scale error with a change in temperature. It is
expressed in ppm FSR/°C.
Gain Error
Gain error is a measure of the span error of the DAC. It is the
deviation in slope of the DAC transfer characteristic from the
ideal, expressed in ppm of the full-scale range.
Gain Error Temperature Coefficient
Gain error temperature coefficient is a measure of the change
in gain error with a change in temperature. It is expressed in
ppm FSR/°C.
Output Voltage Settling Time
Output voltage settling time is the amount of time it takes for
the output voltage to settle to a specified level for a specified
change in voltage. For fast settling applications, a high speed
buffer amplifier is required to buffer the load from the 3.4 kΩ
output impedance of the AD5790, in which case, it is the
amplifier that determines the settling time.
Digital-to-Analog Glitch Impulse
Digital-to-analog glitch impulse is the impulse injected into the
analog output when the input code in the DAC register changes
state. It is specified as the area of the glitch in nV-s and is
measured when the digital input code is changed by 1 LSB at
the major carry transition. See Figure 48.
Output Enabled Glitch Impulse
Output enabled glitch impulse is the impulse injected into the
analog output when the clamp to ground on the DAC output is
removed. It is specified as the area of the glitch in nV-sec (see
Figure 48).
Digital Feedthrough
Digital feedthrough is a measure of the impulse injected into
the analog output of the DAC from the digital inputs of the
DAC but is measured when the DAC output is not updated. It is
specified in nV-sec and measured with a full-scale code change
on the data bus, that is, from all 0s to all 1s, and vice versa.
Total Harmonic Distortion (THD)
Total harmonic distortion is the ratio of the rms sum of the
harmonics of the DAC output to the fundamental value. Only
the second to fifth harmonics are included.
DC Power Supply Rejection Ratio
DC power supply rejection ratio is a measure of the rejection of
the output voltage to dc changes in the power supplies applied
to the DAC. It is measured for a given dc change in power
supply voltage and is expressed in µV/V.
AC Power Supply Rejection Ratio (AC PSRR)
AC power supply rejection ratio is a measure of the rejection of
the output voltage to ac changes in the power supplies applied
to the DAC. It is measured for a given amplitude and frequency
change in power supply voltage and is expressed in decibels.
Midscale Error
Midscale error is a measure of the output error when midscale
code (0x80000) is loaded to the DAC register. Ideally, the output
voltage should be (VREFP − VREFN)/2 + VREFN. Midscale error is
expressed in LSBs.
Rev. D | Page 17 of 28
AD5790
Data Sheet
THEORY OF OPERATION
R
R
R
VOUT
2R
2R ..................... 2R
2R
2R .......... 2R
S0
S1 ..................... S13
E62
E61.........
E0
VREFP
VREFN
14-BIT R-2R LADDER
DAC ARCHITECTURE
10239-050
The AD5790 is a high accuracy, fast settling, single, 20-bit,
serial input, voltage-output DAC. It operates from a VDD supply
voltage of 7 V to 16.5 V and a VSS supply of −16.5 V to -2.5 V.
Data is written to the AD5790 in a 24-bit word format via a 3-wire
serial interface. The AD5790 incorporates a power-on reset
circuit that ensures the DAC output powers up to 0 V with the
VOUT pin clamped to AGND through a ~6 kΩ internal resistor.
SIX MSBs DECODED INTO
63 EQUAL SEGMENTS
Figure 49. DAC Ladder Structure
The architecture of the AD5790 consists of two matched DAC
sections. A simplified circuit diagram is shown in Figure 49.
The six MSBs of the 20-bit data-word are decoded to drive
63 switches, E0 to E62. Each of these switches connects one of
63 matched resistors to either the buffered VREFP or buffered
VREFN voltage. The remaining 14 bits of the data-word drive
Switches S0 to S13 of a 14-bit voltage mode R-2R ladder
network.
SERIAL INTERFACE
The AD5790 has a 3-wire serial interface (SYNC, SCLK, and
SDIN) that is compatible with SPI, QSPI, and MICROWIRE
interface standards, as well as most DSPs (see Figure 2 for a
timing diagram).
Input Shift Register
The input shift register is 24 bits wide. Data is loaded into the
device MSB first as a 24-bit word under the control of a serial
clock input, SCLK, which can operate at up to 35 MHz. The
input register consists of a R/W bit, three address bits and
20 data bits as shown in Table 6. The timing diagram for this
operation is shown in Figure 2.
Table 6. Input Shift Register Format
MSB
DB23
R/W
LSB
DB22
DB21
Register address
DB20
Table 7. Decoding the Input Shift Register
R/W
X1
0
0
0
0
1
1
1
1
Register Address
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
0
0
1
0
1
0
0
1
1
Description
No operation (NOP). Used in readback operations.
Write to the DAC register.
Write to the control register.
Write to the clearcode register.
Write to the software control register.
Read from the DAC register.
Read from the control register.
Read from the clearcode register.
X is don’t care.
Rev. D | Page 18 of 28
DB19 to DB0
Register data
Data Sheet
AD5790
STANDALONE OPERATION
Synchronous DAC Update
The serial interface works with both a continuous and noncontinuous serial clock. A continuous SCLK source can be used
only if SYNC is held low for the correct number of clock cycles.
In this mode, LDAC is held low while data is being clocked into
the input shift register. The DAC output is updated on the rising
edge of SYNC.
In gated clock mode, a burst clock containing the exact number
of clock cycles must be used, and SYNC must be taken high
after the final clock to latch the data. The first falling edge of
SYNC starts the write cycle. Exactly 24 falling clock edges must
be applied to SCLK before SYNC is brought high again. If
SYNC is brought high before the 24th falling SCLK edge, the
data written is invalid. If more than 24 falling SCLK edges are
applied before SYNC is brought high, the input data is also
invalid.
Asynchronous DAC Update
The input shift register is updated on the rising edge of SYNC.
For another serial transfer to take place, SYNC must be brought
low again. After the end of the serial data transfer, data is
automatically transferred from the input shift register to the
addressed register. When the write cycle is complete, the output
can be updated by taking LDAC low while SYNC is high.
Readback
The contents of all the on-chip registers can be read back via
the SDO pin. Table 7 outlines how the registers are decoded.
After a register has been addressed for a read, the next 24 clock
cycles clock the data out on the SDO pin. The clocks must be
applied while SYNC is low. When SYNC is returned high, the
SDO pin is placed in tristate. For a read of a single register, the
NOP function can be used to clock out the data. Alternatively,
if more than one register is to be read, the data of the first
register to be addressed can be clocked out at the same time
the second register to be read is being addressed. The SDO pin
must be enabled to complete a readback operation. The SDO
pin is enabled by default.
HARDWARE CONTROL PINS
In this mode, LDAC is held high while data is being clocked
into the input shift register. The DAC output is asynchronously
updated by taking LDAC low after SYNC has been taken high.
The update now occurs on the falling edge of LDAC.
Reset Function (RESET)
The AD5790 can be reset to its power-on state by two means:
either by asserting the RESET pin or by using the software reset
control function (see Table 13). If the RESET pin is not used,
hardwire it to IOVCC.
Asynchronous Clear Function (CLR)
The CLR pin is an active low clear that allows the output to
be cleared to a user defined value. The 20-bit clear code value
is programmed to the clearcode register (see Table 12). It is
necessary to maintain CLR low for a minimum amount of time
to complete the operation (see Figure 2).When the CLR signal
is returned high the output remains at the clear value (if LDAC
is high) until a new value is loaded to the DAC register. The
output cannot be updated with a new value while the CLR pin is
low. A clear operation can also be performed by setting the CLR
bit in the software control register (see Table 13).
ON-CHIP REGISTERS
DAC Register
Table 9 outlines how data is written to and read from the DAC
register.
The following equation describes the ideal transfer function of
the DAC:
Load DAC Function (LDAC)
After data has been transferred into the input register of the
DAC, there are two ways to update the DAC register and DAC
output. Depending on the status of both SYNC and LDAC, one
of two update modes is selected: synchronous DAC update or
asynchronous DAC update.
VOUT =
(VREFP − VREFN ) × D
2 20
+ VREFN
where:
VREFN is the negative voltage applied at the VREFN input pin.
VREFP is the positive voltage applied at the VREFP input pin.
D is the 20-bit code programmed to the DAC.
Rev. D | Page 19 of 28
AD5790
Data Sheet
Table 8. Hardware Control Pins Truth Table
LDAC
X1
X1
0
0
1
CLR
X1
X1
0
1
0
1
0
1
0
1
0
1
0
1
RESET
0
1
1
1
1
1
1
1
1
1
1
1
Function
The AD5790 is in reset mode. The device cannot be programmed.
The AD5790 is returned to its power-on state. All registers are set to their default values.
The DAC register is loaded with the clearcode register value and the output is set accordingly.
The output is set according to the DAC register value.
The DAC register is loaded with the clearcode register value and the output is set accordingly.
The output is set according to the DAC register value.
The output remains at the clearcode register value.
The output remains set according to the DAC register value.
The output remains at the clearcode register value.
The DAC register is loaded with the clearcode register value and the output is set accordingly.
The DAC register is loaded with the clearcode register value and the output is set accordingly.
The output remains at the clearcode register value.
The output is set according to the DAC register value.
X is don’t care.
Table 9. DAC Register
MSB
DB23
R/W
DB22
DB21
Register address
DB20
DB19 to DB0
DAC register data
LSB
R/W
0
0
1
20 bits of data
Rev. D | Page 20 of 28
Data Sheet
AD5790
Control Register
is asserted. The output value depends on the DAC coding that is
being used, either binary or twos complement. The default
register value is 0.
The control register controls the mode of operation of the
AD5790.
Clearcode Register
The clearcode register sets the value to which the DAC output is
set when the CLR pin or CLR bit in the software control register
Table 10. Control Register
MSB
DB23
LSB
DB19 to DB11
DB10
R/W
DB22 DB21 DB20
Register address
R/W
0
Reserved
Reserved
1
0
DB9
DB8
DB7
DB6 DB5
DB4
Control register data
0000
SDODIS
BIN/2sC
DB3
DB2
DB1
DB0
DACTRI
OPGND
RBUF
Reserved
Table 11. Control Register Functions
Bit Name
Reserved
RBUF
OPGND
DACTRI
BIN/2sC
SDODIS
R/W
Description
These bits are reserved and should be programmed to zero.
Output amplifier configuration control.
0: the internal amplifier, A1, is powered up and Resistors RFB and R1 are connected in series, as shown in Figure 52. This
allows an external amplifier to be connected in a gain of two configuration. See the AD5790 Features section for further
details.
1: (default) the internal amplifier, A1, is powered down and Resistors RFB and R1 are connected in parallel, as shown in Figure 51,
so that the resistance between the RFB and INV pins is 3.4 kΩ, equal to the resistance of the DAC. This allows the RFB and INV
pins to be used for input bias current compensation for an external unity-gain amplifier. See the AD5790 Features section
for further details.
Output ground clamp control.
0: the DAC output clamp to ground is removed and the DAC is placed in normal mode.
1: (default) the DAC output is clamped to ground through a ~6 kΩ resistance, and the DAC is placed in tristate mode.
Resetting the part puts the DAC in OPGND mode, where the output ground clamp is enabled and the DAC is tristated.
Setting the OPGND bit to 1 in the control register overrules any write to the DACTRI bit.
DAC tristate control.
0: the DAC is in normal operating mode.
1: (default) DAC is in tristate mode.
DAC register coding selection.
0: (default) the DAC register uses twos complement coding.
1: the DAC register uses offset binary coding.
SDO pin enable/disable control.
0: (default) the SDO pin is enabled.
1: the SDO pin is disabled (tristate).
Read/write select bit.
0: AD5790 is addressed for a write operation.
1: AD5790 is addressed for a read operation.
Table 12. Clearcode Register
MSB
DB23
R/W
LSB
DB22
DB21
Register address
DB20
DB19 to DB0
Clearcode register data
R/W
0
1
1
20 bits of data
Rev. D | Page 21 of 28
AD5790
Data Sheet
Software Control Register
This is a write only register in which writing a 1 to a particular bit has the same effect as pulsing the corresponding pin low.
Table 13. Software Control Register
MSB
DB23
R/W
DB22
0
1
1
2
LSB
DB21
DB20
Register address
0
0
DB19 to DB3
Reserved
DB2
DB1
Software control register data
Reset
CLR 1
DB0
LDAC 2
The CLR function has no effect when the LDAC pin is low.
The LDAC function has no effect when the CLR pin is low.
Table 14. Software Control Register Functions
Bit Name
LDAC
CLR
Reset
Description
Setting this bit to 1 updates the DAC register and consequently the DAC output.
Setting this bit to 1 sets the DAC register to a user defined value (see Table 12) and updates the DAC output. The output
value depends on the DAC register coding that is being used, either binary or twos complement.
Setting this bit to 1 returns the AD5790 to its power-on state.
Rev. D | Page 22 of 28
Data Sheet
AD5790
AD5790 FEATURES
POWER-ON TO 0 V
Unity-Gain Configuration
The AD5790 contains a power-on reset circuit that, as well as
resetting all registers to their default values, controls the output
voltage during power-up. Upon power-on, the DAC is placed in
tristate (its reference inputs are disconnected), and its output is
clamped to AGND through a ~6 kΩ resistor. The DAC remains
in this state until programmed otherwise via the control register.
This is a useful feature in applications where it is important to
know the state of the DAC output while it is in the process of
powering up.
Figure 50 shows an output amplifier configured for unity gain.
In this configuration, the output spans from VREFN to VREFP.
VREFP
A1
6.8kΩ 6.8kΩ
R1
INV
AD8675
ADA4898-1
ADA4004-1
VOUT
DAC OUTPUT STATE
The DAC output can be placed in one of three states, controlled
by the DACTRI and OPGND bits of the control register, as
shown in Table 15.
Table 15. Output State Truth Table
Output State
Normal operating mode
Output is clamped via ~6 kΩ to AGND
Output is in tristate
Output is clamped via ~6 kΩ to AGND
10239-052
AD5790
After power-on, the AD5790 must be configured to put it into
normal operating mode before programming the output. To do
this, the control register must be programmed. The DAC is
removed from tristate by clearing the DACTRI bit, and the
output clamp is removed by clearing the OPGND bit. At this
point, the output goes to VREFN, unless an alternative value is
first programmed to the DAC register.
VREFN
Figure 50. Output Amplifier in Unity-Gain Configuration
A second unity-gain configuration for the output amplifier is
one that removes an offset from the input bias currents of the
amplifier. It does this by inserting a resistance in the feedback
path of the amplifier that is equal to the output resistance of the
DAC. The DAC output resistance is 3.4 kΩ. By connecting R1
and RFB in parallel, a resistance equal to the DAC resistance is
available on chip. Because the resistors are all on one piece of
silicon, they are temperature coefficient matched. To enable this
mode of operation the RBUF bit of the control register must be
set to Logic 1. Figure 51 shows how the output amplifier is
connected to the AD5790. In this configuration, the output
amplifier is in unity gain and the output spans from VREFN to
VREFP. This unity-gain configuration allows a capacitor to be placed
in the amplifier feedback path to improve dynamic performance.
VREFP
RFB
OUTPUT AMPLIFIER CONFIGURATION
R1
6.8kΩ
There are a number of different ways that an output amplifier
can be connected to the AD5790, depending on the voltage
references applied and the desired output voltage span.
20-BIT
DAC
RFB
6.8kΩ
INV
VOUT
VOUT
AD8675
ADA4898-1
ADA4004-1
AD5790
VREFN
10pF
10239-053
OPGND
0
1
0
1
RFB
VOUT
20-BIT
DAC
CONFIGURING THE AD5790
DACTRI
0
0
1
1
RFB
Figure 51. Output Amplifier in Unity Gain with Amplifier Input Bias Current
Compensation
Rev. D | Page 23 of 28
AD5790
Data Sheet
Gain of Two Configuration (×2 Gain Mode)
VREFP
Rev. D | Page 24 of 28
A1
6.8kΩ 6.8kΩ
R1
20-BIT
DAC
RFB
RFB
INV
10pF
VOUT
VOUT
AD8675
ADA4898-1
ADA4004-1
AD5790
VREFN
Figure 52. Output Amplifier in Gain of Two Configuration
10239-054
Figure 52 shows an output amplifier configured for a gain of
two. The gain is set by the internal matched 6.8 kΩ resistors,
which are exactly twice the DAC resistance, having the effect of
removing an offset from the input bias current of the external
amplifier. In this configuration, the output spans from 2 ×
VREFN − VREFP to VREFP. This configuration is used to generate a
bipolar output span from a single ended reference input with
VREFN = 0 V. For this mode of operation, the RBUF bit of the
control register must be cleared to Logic 0.
Data Sheet
AD5790
APPLICATIONS INFORMATION
TYPICAL OPERATING CIRCUIT
10239-055
Figure 53. Typical Operating Circuit
Rev. D | Page 25 of 28
AD5790
Data Sheet
Figure 53 shows a typical operating circuit for the AD5790
using an AD8675 as an output buffer. Because the output
impedance of the AD5790 is 3.4 kΩ, an output buffer is
required for driving low resistive, high capacitive loads.
EVALUATION BOARD
An evaluation board is available for the AD5790 to aid
designers in evaluating the high performance of the part
with minimum effort. The AD5790 evaluation kit includes
a populated and tested AD5790 printed circuit board (PCB).
The evaluation board interfaces to the USB port of a PC. Software is available with the evaluation board to allow the user to
easily program the AD5790. The software runs on any PC that
has Microsoft® Windows® XP (SP2), or Vista (32-bit or 64-bit),
or Windows 7 installed. The AD5790 user guide, UG-342, is
available, which gives full details on the operation of the
evaluation board.
Rev. D | Page 26 of 28
Data Sheet
AD5790
OUTLINE DIMENSIONS
2.75
2.65
2.50
4.00 BSC
PIN 1
INDICATOR
20
PIN 1
INDICATOR
1
19
0.50
BSC
3.75
3.65
3.50
EXPOSED
PAD
7
13
TOP VIEW
1.00
0.90
0.80
SEATING
PLANE
0.30
0.25
0.20
0.50
0.40
0.30
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
8
12
BOTTOM VIEW
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
04-11-2012-B
5.00 BSC
(Chamfer 0.225)
24
Figure 54. 24-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 5 mm Body, Very Thin Quad
(CP-24-5)
Dimensions shown in millimeters
ORDERING GUIDE
Model1
AD5790BCPZ
AD5790BCPZ-RL7
EVAL-AD5790SDZ
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
INL
±4 LSB
±4 LSB
Z = RoHS Compliant Part.
Rev. D | Page 27 of 28
Package Description
24-Lead LFCSP_VQ
24-Lead LFCSP_VQ
Evaluation Board
Package Option
CP-24-5
CP-24-5
AD5790
Data Sheet
NOTES
©2011-2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10239-0-7/13(D)
Rev. D | Page 28 of 28