EVAL-AD5665R: Evaluation Board for Quad, 16-Bit, I 2 C Interface, Voltage Output DAC PDF

Evaluation Board for Quad, 16-Bit,
I2C Interface, Voltage Output DAC
EVAL-AD5665R
FEATURES
GENERAL DESCRIPTION
Full-featured evaluation board for the AD5665R
2 DAC footprints to allow evaluation of both package options
EVAL-AD5665REBZ1 is populated with the
AD5665RBRUZ-2 TSSOP package
EVAL-AD5665REBZ2 is populated with the
AD5665RBCPZ LFCSP package
On-board reference
On-board ADC for voltage readback
Various link options
Direct hookup to USB port of PC
PC software for control of DACs
This data sheet describes the evaluation board for the AD5665R
quad, 16-bit DAC. The AD5665R operates from a single 2.7 V
to 5.5 V supply. The part incorporates an internal 1.25 V or 2.5
V on-chip reference to give an output voltage span of 2.5 V or
5 V, respectively. The on-chip reference is off at power-up,
allowing for the use of an external reference (the AD780 on this
evaluation board). The part must be written to after power-up
to turn on the internal reference.
Complete specifications for the AD5665R can be found in the
AD5665R data sheet available from Analog Devices, Inc., and
should be consulted in conjunction with this data sheet when
using the evaluation board.
This board can also be used to evaluate the AD5665 part. Full
data on the AD5665 can be found in the AD5665 data sheet
available from Analog Devices.
The evaluation board interfaces to the USB port of an IBM®compatible PC. Software is available with the evaluation board,
allowing the user to easily program the AD5665R.
FUNCTIONAL BLOCK DIAGRAM
POWER SUPPLY INPUTS
EXT REF IN/
INT REF OUT
3V VOLTAGE
REFERENCE
USB CONNECTOR
SMB CONNECTORS
VREF
VOUTA
VOUTB
CONTROLLER
AD5665R
I/O
ADG728
8:1 MUX
ADC
CY7C68013
07305-001
VOUTD
Figure 1.
Rev. 0
Evaluation boards are only intended for device evaluation and not for production purposes.
Evaluation boards are supplied “as is” and without warranties of any kind, express, implied, or
statutory including, but not limited to, any implied warranty of merchantability or fitness for a
particular purpose. No license is granted by implication or otherwise under any patents or other
intellectual property by application or use of evaluation boards. Information furnished by Analog
Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result
from its use. Analog Devices reserves the right to change devices or specifications at any time
without notice. Trademarks and registered trademarks are the property of their respective owners.
Evaluation boards are not authorized to be used in life support devices or systems.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
www.analog.com
Tel: 781.329.4700
Fax: 781.461.3113
©2008 Analog Devices, Inc. All rights reserved.
EVAL-AD5665R
TABLE OF CONTENTS
Features .............................................................................................. 1 Installing the Software ..................................................................5 General Description ......................................................................... 1 Software Operation .......................................................................5 Functional Block Diagram .............................................................. 1 Evaluation Board Schematics and Artwork ...................................8 Revision History ............................................................................... 2 Ordering Information .................................................................... 12 Evaluation Board Hardware ............................................................ 3 Bill of Materials ........................................................................... 12 Power Supplies .............................................................................. 3 Ordering Guide .......................................................................... 12 Link Options ................................................................................. 3 ESD Caution................................................................................ 12 Evaluation Board Software .............................................................. 5 REVISION HISTORY
1/08—Revision 0: Initial Version
Rev. 0 | Page 2 of 2
EVAL-AD5665R
EVALUATION BOARD HARDWARE
POWER SUPPLIES
To power the EVAL-AD5665REBZ, supply the voltage (2.7 V to
5.5 V) between the AVDD and AGND inputs for the analog
supply of the AD5665R (J6). Alternatively, placing Link 6 in
Position B powers the analog circuitry from the USB port
(default setting). This powers all devices with 3.3 V supply.
Both AGND and DGND inputs are provided on the board. The
AGND and DGND planes are connected at one location close
to the AD5665R. To avoid ground loop problems, it is recommended not to connect AGND and DGND elsewhere in the
system.
Each supply is decoupled to the relevant ground plane with
10 μF and 0.1 μF capacitors. Each device supply pin is also
decoupled with a 10 μF and 0.1 μF capacitor pair to the relevant
ground plane.
LINK OPTIONS
A number of link and switch options on the evaluation board
should be set for the required operating setup before using the
board. The functions of these link options are described in
detail in Table 2. The default setup is for control by the PC via
the USB port and for evaluating the part in standard/fast mode
with an external 3 V reference, the AD780. The default link
options are listed in Table 1.
Table 1. Link Options Setup for PC Control (Default)
Link No.
LK1 to LK4
LK5
LK6
LK7
LK8
LK9
LK10
LK11
LK12
LK13
LK14
LK15
LK16
Option
Inserted
B
B
A
A
A
Removed
B
B
A
A
A
Inserted
Table 2. Link Functions
Link No.
LK1 to LK4
LK5
LK6
LK7
LK8
LK9
LK10
LK11
LK12
Function
These links connect the VOUTA to VOUTD pins of the AD5665R to the input pins of ADG728 demultiplexer to monitor the
DAC output value using the on-board AD7992 ADC.
This link selects the AVDD power supply source for the analog circuitry.
Position A selects J6 as the AVDD analog circuitry power supply source.
Position B selects the 3.3 V power supply source as the AVDD analog circuitry power supply source (see LK6).
This link selects the DVDD supply source for the digital circuitry.
Position A selects J7 as the digital circuitry power supply source.
Position B selects the 3.3 V USB as the digital circuitry power supply source.
This link selects whether the AD5665R evaluation board is controlled by the PC via the USB port or by an external source
via the SMB connectors J1 to J12.
Position A selects control by the PC via the USB port.
Position B selects control by an external source via the SMB connectors J1 to J4.
This link sets the RESET pin on the ADG728.
Position A allows normal operation of the switch.
Position B resets the switch.
This link selects the AVDD power supply source for the AD780 reference.
Position A selects J6-3 as the AD780 power supply source.
Position B selects the 5 V USB supply voltage as the AD780 power supply source.
This link connects a 0.1 μF capacitor to AGND on the VREFOUT pin. It is recommended to connect this when using the
internal reference.
This link selects the reference source.
Position A selects the internal reference as the reference source. The part must be written to via software to turn on the
internal reference.
Position B selects the on-board AD780 3 V reference as the reference source.
This link selects whether the part power-on resets to zero-scale or midscale.
Position A ensures that the part power-on resets to midscale.
Position B ensures that the part power-on resets to zero-scale.
Rev. 0 | Page 3 of 3
EVAL-AD5665R
Link No.
LK13
LK14
LK15
LK16
Function
This link selects the DAC voltage source.
Position A selects the AVDD analog circuitry power supply source.
Position B selects the on-board AD780 3 V reference as the power supply source.
This link allows the user to hardwire the ADDR1 pin to set the two LSBs (A1, A0) of the 7-bit address. 00011A1A0
(10-lead LFCSP); 001A3A2A1A0 (14-lead TSSOP).
Position A connects the pin to AVDD; therefore, two LSBs are 00.
Position B connects the pin to GND; therefore, two LSBs are 11.
No connection; therefore, two LSBs are 10.
This link allows the user to hardwire the ADDR2 pin to set the bits (A3, A2) of the 7- bit address. 001A3A2A1A0
(14-lead TSSOP only).
Position A connects the pin to AVDD; therefore, two bits are 00.
Position B connects the pin to GND; therefore, two bits are 11.
No connection; therefore, two bits are 10.
This link connects the OP_SEL pin of the AD780 reference to ground, selecting a 3 V output. Leaving no connect gives a
2.5 V output.
Rev. 0 | Page 4 of 4
EVAL-AD5665R
EVALUATION BOARD SOFTWARE
INSTALLING THE SOFTWARE
3.
The AD5665R evaluation kit includes self-installing software
on CD-ROM. The software is compatible with Microsoft®
Windows® 2000 and Windows XP.
Select the part number of the device on the evaluation
board and click OK.
4.
The main window of AD5665R evaluation software opens,
as shown in Figure 3. The data programmed into the 24-bit
input shift register is displayed. You can select the command
bits, the address bits, and the data bits by clicking the
appropriate option button under each section.
The software should be installed before connecting the evaluation board to the PC’s USB port. This ensures that the board is
correctly recognized when connected to the PC.
1.
Start the Windows operating system and insert the CD-ROM.
2.
The installation software should launch automatically. If it
does not, run the setup.exe file directly from the CD.
3.
4.
1.
After installation from the CD-ROM is complete, power up
the AD5665R evaluation board as described in the Power
Supplies section. Connect the board to the PC’s USB port
using the supplied cable.
To select a command to program the part, click the
appropriate option button under the Command Bits
section. For example, to program all DAC outputs with full
scale, click Write to and Update DAC channel n.
2.
Next, click All DACs in the Address Bits section.
3.
Once the software detects the evaluation board, proceed
through any dialog boxes that appear to finalize the
installation.
Then, in the Data Bits section, enter the data in the Hex
Value or Voltage box.
4.
To execute, click Write to Part. You must click Write to
Part to execute all writes to the part.
SOFTWARE OPERATION
2.
From the Analog Devices menu, click Start > All
Programs > Analog Devices > AD5665R > AD5665R
Evaluation Software.
The AD5665R evaluation software also allows programming of
the power-down DAC bits, the clear code register bits, and the
LDAC register bits by clicking the corresponding option button
under the Command Bits section and then clicking Write to
Part. You can also set the register bits for the required mode of
operation. Consult the AD5665R data sheet for details.
For older PCs, click Start > Programs > Analog Devices >
AD5665R > AD5665R Evaluation Software.
ADC
The device selection window opens, as shown in
Figure 2.
The voltage output on each DAC channel is monitored using
the on-board ADC. To read the output voltage, click the Sample
button in the ADC section (upper right portion of the window).
07305-002
1.
Command Bits
Figure 2. Device Selection Window
Rev. 0 | Page 5 of 5
07305-003
EVAL-AD5665R
Figure 3. AD5665R Evaluation Software Main Window
Rev. 0 | Page 6 of 6
EVAL-AD5665R
Reference Setup
07305-004
The AD5665R internal reference is turned off at power-up by
default, allowing the use of an external reference. To turn on (or
turn off) the internal reference, click Internal Reference Setup
in the Command Bits section. This allows you to program the
bit in the reference setup register for the required mode of
operation, as shown in Figure 4. Then click Write to Part.
Figure 4. AD5665R Evaluation Software Main Window, Reference Setup
Rev. 0 | Page 7 of 7
EVAL-AD5665R
EVALUATION BOARD SCHEMATICS AND ARTWORK
07305-005
Figure 5. Schematic of Controller Circuitry
Rev. 0 | Page 8 of 8
EVAL-AD5665R
07305-006
Figure 6. Schematic of AD5665R Circuitry
Rev. 0 | Page 9 of 9
07305-007
EVAL-AD5665R
07305-008
Figure 7. Component Placement Drawing
Figure 8. Component Side PCB Drawing
Rev. 0 | Page 10 of 10
07305-009
EVAL-AD5665R
Figure 9. Solder Side PCB Drawing
Rev. 0 | Page 11 of 11
EVAL-AD5665R
ORDERING INFORMATION
BILL OF MATERIALS
Table 3.
Qty
1
1
1
1
1
1
1
1
1
1
9
1
1
1
1
1
5
1
2
24
1
2
4
1
4
1
2
2
1
1
6
10
19
Reference Designator
U1
U2
U4
U5
U6
U7
U8
U9
U10
Y1
VOUTA to VOUTD; J1 to J3, J11, J12
J10
J6
J7
D1
L1
C1, C4, C5, C18, C35
C11
C26, C27
C2, C3, C6 ,C7, C8, C9, C12, ,C17, C19 to
C23, C25, C28 to C34, C36, C37, C39
C24
C10, C38
C13 to C16
R1
R2 to R5
R6
R7, R8
R11, R12
R10
R9
LK1 to LK4, LK10, LK16
LK5 to LK9, LK11 to LK15
T1 to T4, T7 to T21
Description
AD5665RBRUZ-2
ADG774BRQ
AD780ARZ
AD7992BRMZ-1
ADG728BRU
ADP3303AR-3.3
CY7C68013-CSP
24LC01
AD5665RBCPZ
24 MHz crystal
Gold 50 Ω SMB jack
USB Mini B
Power connectors
Power connectors
LED
Bead
10 μF 10 V tantalum capacitor (TAJ-B package)
1 μF 10 V tantalum capacitor (TAJ-B package)
22 pF (0603 package)
0.1 μF (0603 package)
Supplier/Number
Analog Devices
Analog Devices
Analog Devices
Analog Devices
Analog Devices
Analog Devices
Embassy CY7C68013-56LFC
FEC 975-8070
Analog Devices
FEC 569-872
FEC 1019324
FEC 476-8309
FEC 963-3972
FEC 963-2980
FEC 515-620
FEC 9526862
FEC 197-130
FEC 1135234
FEC 722-005
FEC 9632972
2.2 μF (0603 package)
1 μF (0603 package)
0805 package (not inserted)
1.5 Ω
Wire-wrap pin (not inserted)
1 kΩ (0603 package)
100 kΩ (0603 package)
2.2 kΩ(0603 package)
10 kΩ (0603 package)
0 Ω (0603 package)
Header (2 × 1 pin)
Header (3 × 1 pin)
Test point
FEC 9632972
FEC 9632972
ORDERING GUIDE
Model
EVAL-AD5665REBZ1 1
EVAL-AD5665REBZ21
1
ESD CAUTION
Description
TSSOP Evaluation Board, Populated with
AD5665RBRUZ-2
LFCSP Evaluation Board, Populated with
AD5665RBCPZ
Z = RoHS Compliant Part.
©2008 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
EB07305-0-1/08(0)
Rev. 0 | Page 12 of 12
FEC 758-267
FEC 911-239
FEC 911 471
FEC 911-276
FEC 911-355
FEC 772-227
FEC 511-705
FEC 511-717
FEC 873-1144