GBU8J~GUB8M(GBU)2014.11_X 02

'hϴ:
d,Zh
'hϴD
ϴDW^'>^^W^^/sdZ/'Zd/&/ZͲϲϬϬΕϭϬϬϬsŽůƚƐ
'h Package
FEATURES
*%8
* Ideal for printed circuit board
* Surge overload rating: 180 Amperes peak
* Moisture Sensitivity Level 1
MECHANICAL DATA
* Case: Molded plastic
* UL listed the recognized component directory, file #E195711
* Epoxy: Device has UL flammability classification 94V-O
* Mounting position: Any
* Teminals:Solder plated, solderable per MIL-STD-750,Method 2026.
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25℃ ambient temperature unless otherwise specified.
Single phase half wave, 60Hz, resistive of inductive load.
For capacitive load, derate current by 20%
CHARACTERISTICS
SYMBOL
Mark Code
GBU8J
GBU8K
GBU8M
UNIT
GBU8J
GBU8K
GBU8M
UNIT
1000
Volts
Maximum Recurrent Peak Reverse Voltage
VRRM
600
800
Maximum RMS Voltage
VRMS
420
560
700
Volts
VDC
600
800
1000
Volts
Maximum DC Blocking Voltage
Maximum Average Forward TC=60℃
Rectified Output Current at TA=25℃ (see Fig.1)
Peak Forward Surge Current 8.3 ms single half sine-wave
I(AV)
8.0
3.0
Amps
IFSM
180
Amps
I2t
134.4
A2sec
RΘJA
20
RΘJC
4
Typical Junction Capacitance (Note 1)
CJ
94
PF
Operating Temperature Range
TJ
-55 to +150
℃
TSTG
-55 to +150
℃
VF
1.1
Volts
superimposed on rated load (JEDEC method)
Rating for fusing (t<8.3ms)
Typical Thermal Resistance (Note 2)
(Note 3)
Storage Temperature Range
Forward Voltage Range at 8.0A DC
Maximum Average Reverse Current at
@TA=25℃
Rated DC Blocking Voltage
@TA=125℃
IR
5.0
500
℃/W
μAmps
NOTES :1. Measured at 1 MHz and applied reverse voltage of 4.0 volts.
2. Device mounted in free air,no heatsink,P.C.B at 0.375"(9.5MM) lead length with 0.5 x 0.5"(12 x 12MM) copper pads.
3. Device mounted on a 2.6 x 1.4' x 0.06' tjick (6.5 x 3.5 x 0.15 cm) AL plate.
2014.11
www.willas.com.tw
Rev.X02
P1
'hϴ:
d,Zh
'hϴD
ϴDW^'>^^W^^/sdZ/'Zd/&/ZͲϲϬϬΕϭϬϬϬsŽůƚƐ
'h Package
RATING AND CHARACTERISTICS CURVES
Average Forw ard Output Current (A)
8.0
250
6.0
4.0
2.0
0
PCB Mounting, TA
25
0
50
75
125
100
200
150
100
50
0
150
Number of Cycles at 60 Hz
Figure 1. Derating Curve Output Rectified Current
Figure 2. Maximum Non-Repetitive Peak Forward Surge
Current Per Diode
1000
Junction Capacitance (pF)
10
1
0.1
0.01
Tj = 25 °C
Pulse Width = 300 µs
1 % Duty Cycle
0.4
0.6
0.8
1.0
1.2
1.4
Tj = 25 °C
f = 1.0 MHz
Vsig = 50 mVp-p
100
50 - 400 V
600 - 1000 V
10
1.6
0.1
Figure 5. Typical Junction Capacitance Per Diode
Transient Thermal Impedance (°C/W)
Instantaneous Reverse Current (µA)
100
Tj = 150 °C
100
Tj = 125 °C
10
1
600 - 1000 V
0.01
Tj = 25 °C
0
20
40
60
80
10
1
0.1
0.01
100
0.1
1
10
100
t - Heating Time (s)
Percent of Rated Peak Reverse Voltage (%)
Figure 4. Typical Reverse Leakage Characteristics Per Diode
2014.11
100
Reverse Voltage (V)
Figure 3. Typical Forward Characteristics Per Diode
0.1
10
1
Instantaneous Forward Voltage (V)
500
100
10
1
Temperature (°C)
100
Instantaneous Forward Current (A)
Tj = 150 °C
8.3 ms Single Half Sine-Wave
Peak Forward Surge Current (A)
Heatsink Mounting, TC
Figure 6. Typical Transient Thermal Impedance Per Diode
www.willas.com.tw
Rev.X02
P2
'hϴ:
d,Zh
'hϴD
ϴDW^'>^^W^^/sdZ/'Zd/&/ZͲϲϬϬΕϭϬϬϬsŽůƚƐ
'h Package
Outline Drawing
GBU
.143(3.65)
.130(3.30)
.880(22.3)
.850(21.6)
.160(4.10)
.140(3.50)
.075
.740(18.8)
(1.90)R
.720(18.3)
.310(7.90)
.290(7.40)
.085(2.16)
.065(1.65)
.108(2.75)
.057(1.46)
.101(2.56)
.075(1.90)
.093(2.35)
.065(1.65)
.716(18.2)
.685(17.4)
.025(0.64)
.050(1.28)
.031(0.80)
.190(4.83)
.210(5.33)
Dimensions in inches and (millimeters)
2014.11
www.willas.com.tw
.018(0.46)
Rev G
Rev.X02
P3
ϴDW^'>^^W^^/sdZ/'Zd/&/ZͲϲϬϬΕϭϬϬϬsŽůƚƐ
'h Package
'hϴ:
d,Zh
'hϴD
Ordering Information:
Device PN
Part Number - (1)G(2)-WS
Packing
Tube Packing:20pcs/Tube; 1000pcs/Box
Note: 1. Packing code: Empty is Tube Packing
2. RoHS product for packing code suffix ”G”, Halogen free product for packing code suffix "H" .
***Disclaimer***
WILLAS reserves the right to make changes without notice to any product
specification herein, to make corrections, modifications, enhancements or other
changes. WILLAS or anyone on its behalf assumes no responsibility or liability
for any errors or inaccuracies. Data sheet specifications and its information
contained are intended to provide a product description only. "Typical" parameters
which may be included on WILLAS data sheets and/ or specifications can
and do vary in different applications and actual performance may vary over time.
WILLAS does not assume any liability arising out of the application or
use of any product or circuit.
WILLAS products are not designed, intended or authorized for use in medical,
life-saving implant or other applications intended for life-sustaining or other related
applications where a failure or malfunction of component or circuitry may directly
or indirectly cause injury or threaten a life without expressed written approval
of WILLAS. Customers using or selling WILLAS components for use in
such applications do so at their own risk and shall agree to fully indemnify WILLAS
Inc and its subsidiaries harmless against all claims, damages and expenditures.
2014.11
www.willas.com.tw
Rev.X02
P4