IA-XS-2W

IA-XS-2W Series
FIXED INPUT,ISOLATED&REGULATED Dual Output DC/DC Converters
SELECTION GUIDE
Input
FEATURES
RoHS compliant
◆
Efficiency up to 86%
◆
SIP Package
◆
Wide temperature performance at full
◆
2 Watt load,-40°C to 85°C
UL 94V-0 package material
◆
Output
Switching
Frequency
(KHz,Typ)
Nominal
Range
Max
Min
IA0503XS-2W
5
4.75-5.25
±3.3
±150
±15
69
100
IA0505XS-2W
5
4.75-5.25
±5
±200
±20
70
55
IA0509XS-2W
5
4.75-5.25
±9
±100
±10
62
67
IA0512XS-2W
5
4.75-5.25
±12
±83
±9
64
67
IA0515XS-2W
5
4.75-5.25
±15
±67
±7
65
200
IA1205XS-2W
12
11.4-12.6
±5
±150
±15
70
83
IA1209XS-2W
12
11.4-12.6
±9
±100
±10
63
91
IA1212XS-2W
12
11.4-12.6
±12
±83
±9
65
91
IA1215XS-2W
12
11.4-12.6
±15
±67
±7
68
200
IA2405XS-2W
24
22.8-25.2
±5
±150
±15
70
83
IA2409XS-2W
24
22.8-25.2
±9
±100
±10
63
100
IA2412XS-2W
24
22.8-25.2
±12
±83
±9
67
200
IA2415XS-2W
24
22.8-25.2
±15
±67
±7
69
91
Voltage(VDC)
Current
Efficiency
(%,Typ)
Voltage
(VDC)
Order code
No heatsink required
◆
Small Footprint
◆
Industry standard pinout
◆
Power sharing on output
◆
1KVDC isolation
◆
3.3V,5V,9V,12V and 15V output
◆
ISOLATION SPECIFICATIONS
Internal SMD construction
◆
No external components required
◆
MTTF up to 1.5 million hours
◆
Parameter
Test conditions
Min.
Isolation test voltage
Flash tested for 1 minute and 1mA max
1000
Typ.
Max.
Units
VDC
Isolation resistance
Test at Viso=500VDC
1000
MΩ
MODEL SELECTION
IA①05②05③X④ S⑤-2W⑥
①Product Series
③Output Voltage
⑤SIP Package
②Input Voltage
④Fixed Input
⑥Rated Power
APPLICATIONS
The IA_XS-2W series are specially
designed for applications where a group of
polar power supplies are isolated from the
input power supply in a distributed power
supply system on a circuit board.
These products apply to:
1) where the voltage of the input power supply
is fixed (voltage variation ≤±5%);
2) where isolation is necessary between input
and output (isolation voltage ≤1000VDC);
3) where the regulation of the output voltage
and the output ripple noise are demanded.
OUTPUT SPECIFICATIONS
Parameter
Test conditions
Output power
Min
Typ.
0.2
Max.
Units
2
W
Line regulation
For Vin change of ±5%
±0.25
%
Load regulation
10% to 100% full load
±1
%
Output voltage accuracy
100% full load
±3
%
Temperature drift
100% full load
0.03
%/°C
Output Ripple*
20MHz Bandwidth
20
30
MV p-p
Output Noise*
20MHz Bandwidth
75
150
MV p-p
* Test ripple and noise by "parallel cable" method. See detailed operation instructions at Testing of Power
Converter section, application notes.
MICRODC RESERVES THE COPYRIGHT
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 1 of 2
IA-XS-2W Series
TEMPERATURE CHARACTERISTICS
Parameter
Conditions
Recommended circuit
Min.
Typ.
Storage humidity range
Operating temperature
Storage temperature
Lead temperature
Max.
Units
95
%
-40
80
°C
-55
125
°C
30
°C
300
°C
1.5mm from case for 10 seconds
Temp.rise at full load
20
Cooling
To get an extreme low ripple,an "LC" filtering network
may be connected to the input and output ends of the
DC/DC converter, which may produce a more significant
filtering effect.It should also be noted that the inductance
and the frequency of the "LC" filtering network should be
staggered with the DC/DC frequency to avoid mutual
interference (see figure 1).
Free air convection
Case material
Plastic(UL94-V0)
05V output
Continuous
Short circuit protection
Others*
1
MTBF
S
3500
K hours
Weight
5.2
g
*Supply voltage must be discontinued at the end of short circuit duration.
In some circuits which are sensitive to noise and ripple,
a filtering capacitor may be added to the DC/DC output
end and input end to reduce the noise and ripple.
However, the capacitance of the output filter capacitor
must be proper. If the capacitance is too big, a startup
problem might arise. For every channel of output,
provided the safe and reliable operation is ensured, the
greatest capacitance of its filter capacitor sees the
EXTERNAL CAPACITOR TABLE (see Table 1).
TYPICAL CHARACTERISTICS
Temperature Derating Graph
EXTERNAL CAPACITOR TABLE (TABLE 1)
Cin
Vout
Vin
(VDC)
5
Cout
(VDC)
±5
(μF)
4.7
2.2
12
2.2
±9
24
0.47
±12
1
-
-
±15
0.47
It's not recommend to connect any external capacitor in
the application field with less than 0.5 watt output.
OUTLINE DIMENSIONS & PIN CONNECTIONS
SIZE Graph
Input Over-voltage Protection Circuit
RECOMMENDED FOOTPRINT
Top view,grid:2.54mm(0.1inch)
diameter:1.00mm(0.039inch)
The simplest device for input over-voltage protection is
a linear voltage regulator with overheat protection that is
connected to the input end in series (Figure 2).
FOOTPRINT DETAILS
Pin
Note:
Unit:mm(inch)
Pin section:0.50*0.3mm(0.020*0.012inch)
Pin section tolerances:±0.10mm(±0.004inch)
General tolerances:±0.25mm(±0.010inch)
(μF)
4.7
Function
1
VIN
2
GND
7
+V0
9
-V0
10
0V
When the environment temperature is higher than 71℃,
the product output power should be less then 60% of the
rated power.
No parallel connection or plug and play
play.
Use dual output simultaneously, forbid opening output
pin (0V) to use as single output.
All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise
specified.Another 24V products, please inquire Our technical department!
Requirement on output load
To ensure this module can operate efficiently and reliably, During operation, the minimum output load is
not less than 10% of the full load, and that this product should never be operated under no load! If the
actual output power is very small, please connect a resistor with proper resistance at the output end in
parallel to increase the load.or use our company's products with a lower rated output power (IA_XS-1W
series).
RoHS COMPLIANT INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
E-mail:[email protected]
Website:http://www.microdc.cn
REACH COMPLIANT INFORMATION
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 2