MF-XD-1W5 Series 1.5 Watt,Regulated Output &Isolation Voltage 3000VDC DIP24 Package DC/DC Converter Technical Data Input Parameter Conditions Data 4.5~5.5V 10.8~13.2V 21.6~26.4V 25.2~30.8V 43.2~52.8V Uin DC Input Voltage fsw Switching Frequency 20KHZ typ η Efficiency 50% Input Filter Π-Filter FEATURES 1.5 WATTS REGULATED OUTPUT POWER ◆ LOW OUTPUT RIPPLE & NOISE ◆ PI TYPE INPUT FILTER Technical Data Output 3000VDC ISOLATION VOLTAGE Parameter ◆ ◆ Conditions Data Uout Output Voltages HIGH EFFICIENCY UP TO 78% △Uout Output Voltages Accuracy STANDARD 24 PIN DIP PACKAGE △UNF/△UHF Ripple&Noise 20 MHz BW 50mVpp max Line Regulation Uin=min/max.Iout=max ±0.3% Load Regulation Iout=25~100% ±0.5% ◆ ◆ Input π-Filter ◆ 50 mV Ripple&Noise ◆ Pover Short Circuit Protection ε Temperature Coefficient Plastic Case Metal Case MODEL SELECTION See table ±4% max Short-term TA= -25~+71℃ ＞71~95℃ ＞71~100℃ ±0.02%/℃ linear to 0% lout linear to 0% lout Conditions Data ① ② ③ ④ ⑤ ⑥ MF 05 12 -X D -1W5(125) ①Product Series ②Input Voltage ③Output Voltage ④Fixed Input ⑤DIP24 Package Style ⑥Rated Power(Output current) Technical Data Parameter APPLICATIONS The DC-DC converter MF-XD-1W5 supplies 1.5 watts max.25 different input/output configurations are available with an isolation voltage of 3000VDC Special features are low ripple&noise and wide temperature range. Uisol p/s Isolation(prim./sec.) 3.0 KVDC Risol Isolation Resistance 109Ω Ck Isolation Capacity 30pF To Operating Temperature Case Temperature Plastic Metal -25~+71℃ Case 95℃ max 100℃ max Uisol=3KVDC, DIP 24 Black plastic non-conductive Conditions Data Technical Data Parameter Cooling Dimensions Weight MICRODC RESERVES THE COPYRIGHT http://www.microdc.cn Natural convection DIP 24 31.8X20.3X10.2 mm 12,5g 1. All data measured at nominal nominal input voltage,full load ambient temperature of 20 ℃ (unless otherwise specified). 2.Technical data subject to change. Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 1 of 2 MF-XD-1W5 Series Type Input Input Current Output Output code V NL mA FL mA V mA MF0505XD-1W5 5 100 MF0512XD-1W5 5 110 620 5 300 550 12 MF0515XD-1W5 5 125 110 550 15 MF1205XD-1W5 100 12 40 260 5 300 MF1212XD-1W5 12 40 215 12 125 MF1215XD-1W5 12 40 215 15 100 MF2405XD-1W5 24 20 130 5 300 MF2412XD-1W5 24 20 115 12 125 MF2415XD-1W5 24 20 115 15 100 MF2805XD-1W5 28 20 110 5 300 MF2812XD-1W5 28 20 100 12 125 MF2815XD-1W5 28 20 100 15 100 MF4805XD-1W5 48 15 65 5 300 MF4812XD-1W5 48 15 60 12 125 MF4815XD-1W5 48 15 60 15 100 DIP24 Case Note: Unit:mm[inch] Pin diameter tolerances:±0.10mm[±0.004inch] General tolerances: ±0.25mm[±0.010inch] Dimensions and Pinning PIN Dual PIN Dual 1 +Vin 14 No Pin 2 +Vin 15 No Pin 3 +Vin 16 No Pin 4 No Pin 17 +Test Point 5 No Pin 20 No Pin 9 No Pin 21 No Pin 10 No Pin 22 -Vin 11 No Pin 23 -Vin 12 -Vout 24 -Vin 13 +Vout RECOMMENDED FOOTPRINT http://www.microdc.cn TUBE OUTLINE DIMENSIONS Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 2 of 2