AD5292: Evaluation Board for the 10-Bit, Serial Input, High Voltage Digital Potentiometer (EVAL-AD5292EBZ) PDF

Evaluation Board for the 10-Bit, Serial
Input, High Voltage Digital Potentiometer
EVAL-AD5292EBZ
FEATURES
GENERAL DESCRIPTION
Full-featured evaluation board for the AD5292
Wiper buffer
4-wire ohm measurement capability
Various link options
Direct hookup to USB port of PC
PC software for control of digipot
20-times programmable
1% resistance precision
This data sheet describes the evaluation board for evaluating
the AD5292 digital potentiometer. This device is a singlechannel, 1024-position digital potentiometer with less than ±1%
end-to-end resistor tolerance error and 20-times programmable
(20 TP) memory. The AD5292 is capable of operating at high
voltages, supporting both dual supply ±10.5 V to ±15 V and
single supply 21 V to 30 V operation.
The AD5292 part uses a versatile 3-wire serial interface that
operates at clock rates of up to 50 MHz and is compatible
with standard SPI, QSPI™, MICROWIRE™, and DSP interface
standards.
PACKAGE CONTENTS
AD5292 evaluation board
AD5292 device
3 V voltage regulator (ADP3303)
Buffer (AD8510)
CD, including
Self-installing software that allows control of the digipot
and exercise of all functions of the device
Electronic version of the device data sheet
Electronic version of the EVAL-AD5292EBZ data sheet
The AD5292 evaluation board incorporates, for the logic
voltage levels, an internal power supply from the USB and
allows an external power supply. The logic voltage levels operate
from single 2.7 V to 5.5 V supplies. The board can operate in
single and dual supply modes and incorporates an output
buffer.
Complete specifications for the AD5292 part can be found in
the AD5292 data sheet available from Analog Devices, Inc., and
should be consulted in conjunction with this data sheet when
using the evaluation board
FUNCTIONAL BLOCK DIAGRAM
DIGITAL POWER SUPPLY
+5V
EXTERNAL ANALOG
POWER SUPPLY
EXT.
VDD
VLOGIC
SPI INTERFACE
RDY
RESET
CONTROLLER
CY7C68013
EEPROM
AD5292
GND
VSS
A
W
B
BUFFER
SMB CONNECTORS
POSITIVE ANALOG
POWER SUPPLY
SMB CONNECTORS
NEGATIVE ANALOG
POWER SUPPLY
08257-001
USB CONNECTORS
+3.3V
Figure 1.
Rev. 0
Evaluation boards are only intended for device evaluation and not for production purposes.
Evaluation boards are supplied “as is” and without warranties of any kind, express, implied, or
statutory including, but not limited to, any implied warranty of merchantability or fitness for a
particular purpose. No license is granted by implication or otherwise under any patents or other
intellectual property by application or use of evaluation boards. Information furnished by Analog
Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result
from its use. Analog Devices reserves the right to change devices or specifications at any time
without notice. Trademarks and registered trademarks are the property of their respective owners.
Evaluation boards are not authorized to be used in life support devices or systems.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
www.analog.com
Tel: 781.329.4700
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
EVAL-AD5292EBZ
TABLE OF CONTENTS
Features .............................................................................................. 1 Installing the Software ..................................................................4 Package Contents .............................................................................. 1 Running the Software ...................................................................4 General Description ......................................................................... 1 Software Operation .......................................................................5 Functional Block Diagram .............................................................. 1 Evalution Board Schematics and Artwork .....................................6 Revision History ............................................................................... 2 Ordering Information .................................................................... 10 Evaluation Board Hardware ............................................................ 3 Bill of Materials ........................................................................... 10 Power Supplies .............................................................................. 3 Ordering Guide .......................................................................... 10 Link Options ................................................................................. 3 ESD Caution................................................................................ 10 Evaluation Board Software .............................................................. 4 REVISION HISTORY
06/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
EVAL-AD5292EBZ
EVALUATION BOARD HARDWARE
POWER SUPPLIES
LINK OPTIONS
The EVAL-AD5292EBZ needs one digital supply and up to two
analog supplies to operate. The digital supply is provided on the
board, or it is possible to use an external supply by placing Link 8
in Position B and connecting a power supply in J4 (see Table 3).
The analog supplies must be provided by the user through
connectors J1, J2 and J3, which are VDD, GND, and VSS, respectively, as shown in Table 1.
A number of link and switch options are incorporated into the
evaluation board and should be set to the required operating
setup before using the board. The functions of these link
options are described in detail in Table 3. Table 2 describes the
positions of the links to control the evaluation board by the PC
via the USB port using the AD5292 in single-supply mode with
the wiper buffer connected.
All supplies are decoupled to ground with 10 μF tantalum and
0.1 μF ceramic capacitors.
Table 2. Link Options Setup for PC Control (Default)
Table 1. Maximum and Minimum Voltages Connectors
Connector No.
J1
J2
J3
J4
Voltage
Analog positive power supply, VDD, as follows:
21 V to 30 V single-supply operation
10.5 V to15 V dual-supply operation
Analog GND
Analog negative power supply, VSS, as follows:
0 V single-supply operation
−10.5 V to −15 V dual-supply operation
Digital power supply from 2.7 V to 5 V
Link No.
LK2
LK4
LK5
LK6
LK7
LK8
LK9
Options
Inserted
Inserted
Inserted
Inserted
Inserted
A
B
Table 3. Link Functions
Link No.
LK1
LK2
LK3
LK4 1
LK5
LK6
LK7 1
LK8
LK9
1
Option
Connects Terminal A of the digipot to VDD.
Connects Terminal W of the digipot to the buffer.
Connects Terminal B of the digipot as follows:
LK3 A—VSS
LK3 B—GND
Connects the negative power supply of the buffer to GND.
Connects the positive power supply of the buffer to VDD.
Allows feedback in the buffer.
Connects the negative power supply of the buffer to VSS.
Selects the digital power supply as follows:
LK8 A—5 V (from USB)
LK8 B—3.3 V (from ADP3303)
LK8 C—external supply from J4 connector
Selects whether the AD5292 evaluation board is controlled by the PC via the USB port or by an external source via the
SMB connectors, as follows:
LK9 A—SMB connectors
LK 9 B—USB port
In single supply-power operation, it is recommended to connect LK4 and LK7.
Rev. 0 | Page 3 of 12
EVAL-AD5292EBZ
EVALUATION BOARD SOFTWARE
INSTALLING THE SOFTWARE
RUNNING THE SOFTWARE
The AD5292 evaluation kit includes self-installing software on a
CD-ROM. The software is compatible with Microsoft® Windows®
2000 and Windows XP.
1.
2.
2.
3.
4.
Start the Windows operating system and insert the
CD-ROM
The installation software must open automatically. If it
does not, run the setup.exe file from the CD.
After installation is completed, power up the evaluation
board as described in the Power Supplies section. Plug the
AD5292 evaluation board into the PC using the USB cable
that is included in the box.
After the software detects the evaluation board, proceed
through any dialog boxes that appear to finalize the
installation.
Figure 2. Error Message
3.
To uninstall the program, click Start, Control Panel, Add
or Remove Programs, AD5292.
The main window of the AD5292 evaluation board
software opens, as shown in Figure 3.
08257-003
1.
08257-002
The software should be installed before the evaluation board
is connected to the USB port of the PC. This ensures that the
board is correctly recognized when connected to the PC.
To run the program, click Start, All Programs, ADI,
AD5292 Eval Board, AD5292 Evaluation Board.
If the PC is not connected to the board via the USB port, a
message box advises you, as shown in Figure 1. Check the
cable between the PC and the board, and click Retry. If the
cable is connected, exit the program and try to reinstall it.
Figure 3. AD5292 Evaluation Board Main Window
Rev. 0 | Page 4 of 12
EVAL-AD5292EBZ
•
SOFTWARE OPERATION
The main window is divided in three sections, as follows:
READ shows the actual value of the RDAC or the value of
the selected 20-TP memory location. These values are
displayed in the resistor, as shown in Figure 4, and are
updated when you read from or write to the part.
08257-005
•
Save Value To 20-TP—saves into the 20-TP memory
the value that is shown in the display (see Figure 5).
It is necessary to click Write To Part to write to the
part.
08257-004
Figure 5. Save Value to 20-TP Option (the Display Is in Hex Format)
Figure 4. Resistor Figure: Left Position, Resistance
from A to W; Right Position, Resistance from W to B
•
WRITE has the following options:
• RDAC—changes the RDAC register contents. The
value is in hex format.
• Control Register—updates the control register
contents.
•
Note that, if the enable program is disabled or the
display value is different from the RDAC register,
Write To Part does not appear (to prevent errors).
• Reset (software)—sends a reset by software. It is
necessary to click Write To Part to send the
command.
REGISTER shows the value of the control register.
There are also three buttons that allow the following functions:
•
•
•
Rev. 0 | Page 5 of 12
Power-down/Power-up—powers the part down and up.
When the button is clicked, the power-up/-down bit
toggles automatically.
Reset—sends a reset by hardware.
EXIT—closes the program (it does not reset the part).
EVAL-AD5292EBZ
EVALUTION BOARD SCHEMATICS AND ARTWORK
U1
AD5292
EXT_CAP
VDD
VSS
VLOGIC
08257-006
Figure 6. Schematic of the AD5292 Circuitry
Rev. 0 | Page 6 of 12
EVAL-AD5292EBZ
SHIELD
08257-007
Figure 7. Schematic of the Controller Circuitry
Rev. 0 | Page 7 of 12
08257-008
EVAL-AD5292EBZ
08257-009
Figure 8. Component Placement Drawing
Figure 9. Component Side PCB Drawing
Rev. 0 | Page 8 of 12
08257-010
EVAL-AD5292EBZ
Figure 10. Solder Side PCB Drawing
Rev. 0 | Page 9 of 12
EVAL-AD5292EBZ
ORDERING INFORMATION
BILL OF MATERIALS
Table 4.
Qty
25
1
3
4
2
1
2
1
1
1
1
1
7
1
1
4
1
2
1
1
16
1
2
1
1
1
1
1
1
Reference Designator
C1 to C3, C5, C7, C10, C12, C14 to C23,
C25 to C30, C34
C4
C13, C24, C33
C6, C8, C9, C11
C31, C32
D1
DGND, AGND
J1
J2
J3
J4
J5
LK1 to LK7
LK8
LK9
R1, R2, R8, R9
R4
R5, R6
R7
R15
T1 to T8, TP-VOUT, VDD, VLOGIC, VSS,
W, A, 3V3, B
U1
U2, U3
U4
U5
U6
U7
Y1
Supplier1/Number
FEC 1288255
Capacitor, 1 μF, 16 V, 0805, SMD
Capacitor, 10 μF, 10 V, tantalum, SMD
Capacitor, 10 μF, 35 V, dielectric tantalum
Capacitor, 12 pF, 50 V, 0603, SMD
LED, SMD green
Testpoint, black
Banana-red, socket, 4 mm
Banana-black, socket, 4 mm
Banana-red, socket, 4 mm
Connector\power, 2-way, PCB
USB-MINI-B
Jumper and socket
Jumper-3 and socket, 36-pin strip
Jumper2\SIP3 and socket
Resistor, 2.2 kΩ
Resistor, 1 kΩ, 0603
Resistor, 100 kΩ, 0603
Resistor, 10 kΩ. 0603
Resistor, 0 Ω, 0603
Testpoint, red, PCB
FEC 952-7710
FEC 197-130
FEC 970-8570
FEC 721-979
FEC 5790852
FEC 8731128
FEC 1101127
FEC 1101128
FEC 1101130
FEC 151789
FEC 56579-0576
FEC 1022247 and FEC 150-411
FEC 148-535 and FEC150-411
FEC 1022248 and FEC 150410
FEC 9330810
FEC 9330380
FEC 9330402
FEC 9330399
FEC 9331662
FEC 8731144
AD5292
ADG774
AD8510
ADP3303-3.3
CY7C68013-CSP microcontroller, 15 kB
24LC01, EEPROM, 64 k, SOIC8
XTAL1-CSM-8A, crystal, 24.0 MHz, 12 pF, SMD
Analog Devices
Analog Devices
Analog Devices
Analog Devices
FEC 1269133
FEC 9758070
Digi-Key XC1009CT-ND
FEC refers to Farnell Electronic Component Distributors; Digi-Key refers to Digi-Key Corporation.
ESD CAUTION
ORDERING GUIDE
Model
EVAL-AD5292EBZ1
1
Description
Capacitor, 0.1 μF, 50 V, 0603, SMD
Package
Evaluation Board
Z = RoHS Compliant Part.
Rev. 0 | Page 10 of 12
EVAL-AD5292EBZ
NOTES
Rev. 0 | Page 11 of 12
EVAL-AD5292EBZ
NOTES
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
EB08257-0-6/09(0)
Rev. 0 | Page 12 of 12